FT1000S
FT1000S ENERGY RECOVERY
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Item # _____________________________________
Quantity ___________________________________
C.S.I. Section 11400
WITH BLOWER DRYER
FLIGHT-TYPE DISHWASHER
STANDARD FEATURES
■ Pumped rinse system (pressure gauge not
required)
■ Water usage 58 gph
■ Digital controls with machine diagnostics
■ Low temperature alert
■ Single point vent location
■ 31" access on prewash and power wash
chambers; 20" access on dual rinse and ASR
chambers
■ Start and stop switches at both ends
■ Doors open indicator
■ Drains open indicator
■ Door interlocks
■ 31⁄2 H.P. prewash, and 5 H.P. power wash pump
motors, all TEFC
■ Capless Auto Clean wash arms
■ Easy to remove stainless steel scrap pans and
baskets
■ 30" wide conveyor belt
■ Dual Rinse
■ Automatic Soil Removal system (ASR)
■ Auto Clean
■ Auto Delime
■ Energy Recovery
■ Front and rear panels
■ Variable speed conveyor
MODEL
❑ FT1000S Energy Recovery with Blower Dryer
Flight-Type Dishwasher
OPTIONS AT EXTRA COST
❑ Electric Tank Heat
❑ Steam Tank Heat
❑ Booster Heater
❑ Electric
❑ Steam
❑ Blower Dryer
❑ Electric
❑ Steam
❑ 6" higher than standard chamber
❑ Multiple conveyor choices
❑ Circuit breakers
❑ Security package
❑ Other options available, consult factory
ACCESSORIES
❑ Flanged feet
❑ Water hammer arrestor/PRV (installed by others)
❑ Drain water tempering kit (installed by others)
❑ Vent connection kit
Specications, Details and Dimensions on Inside and Back.
FT1000S ENERGY RECOVERY WITH BLOWER DRYER FLIGHT-TYPE DISHWASHER
DIRECTION OF OPERATION
❑ Right to Left
❑ Left to Right
• LA Research Report M660004
• Complies with EPA Reduction of Lead in Drinking
Water Act 2014
• Meets requirements of ASSE Standard No. 1004
VOLTAGE
❑ 208/60/3
❑ 240/60/3
❑ 480/60/3
❑ Other voltages available – consult factory
F40393 – FT1000S Energy Recovery with Blower Dryer Flight-Type Dishwasher Page 1 of 12
FT1000S ENERGY RECOVERY
WITH BLOWER DRYER
FLIGHT-TYPE DISHWASHER
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
DESIGN: Fully automatic, ight-type dish machine
consisting of a load section with Automatic Soil
Removal system, power recirculating prewash, power
wash and dual rinse/nal rinse section. Included with
each machine will be exible plastic strip curtains to
control overspray.
CONSTRUCTION: Stainless steel tank and chambers
with No. 3 polish on appearance surfaces. Frame,
legs and feet to be constructed of stainless steel.
Inspection doors to be chamber width.
PUMPS: Recirculating stainless steel pumps with
stainless steel impellers. Pump housing has easy
to remove coverplate for access to impeller. Wash
pumps are self-draining.
MOTORS: Totally enclosed fan cooled (TEFC) design
with overload protection. Pump motors to be 31⁄2 H.P.
for prewash, 5 H.P. for power wash, and conveyor
motor to be 1⁄3 H.P. Available in electrical specications of 208/60/3, 240/60/3 and 480/60/3.
CONTROLS: A stainless steel control center with
electronic digital controls mounted at eye level.
Power “On/Off” and “Start/Stop” switches integrated
into keypad. Digital display indicates door(s) open,
low temperature alert, tanks/nal rinse temperatures,
Auto Clean and Auto Delime instructions and notications, and other pertinent operating data. Additional
“Start/Stop” switches are located at each end of
machine. Conveyor speed button to be included on
the control center to provide for the adjustable speed
conveyor.
FLIGHT-TYPE CONVEYOR: Stainless steel side
links, tie rods and conveyor tracks. Injection molded,
resilient Duraex ight links.
VENT: Indirect vent connection with integral powered
fan.
AUTOMATIC SOIL REMOVAL SYSTEM (ASR):
Two foot section with specialized soil removal wash
arms which removes food soil from the ware before
it reaches the prewash tank. System will pump
food soil from the ASR tank into an external collector located under the load section, minimizing the
need to pre-scrap dishes and reducing detergent
consumption. Operator can easily remove and clean
external collector without interruption of machine
operation.
RECIRCULATING PREWASH SECTION: Prewash
compartment is tted with upper and lower wash
arms. Large removable one piece perforated stainless
steel screen sloped downward to deep stainless steel
scrap basket.
TANK HEAT: Power wash and dual rinse tank water
temperatures are thermostatically controlled. Low
water protection is provided. Specify either electric
or steam heat.
FINAL RINSE: Easily removed nal rinse arms.
ENERGY RECOVERY: Energy Recovery system
operates with a cold water line, capturing energy from
exhaust air, and using it to elevate the temperature
of the water entering the booster heater. The result is
savings – both in hot water and in energy.
CONVEYOR DRIVE UNIT: Powered by a 1⁄3 H.P.
motor. Trip mechanism provided on unload section.
Jam protection is provided by load sensing switch at
drive platform. Conveyor speed adjustment of 4 feet
per minute to 6.3 feet per minute is provided on the
digital display keypad.
DRAINS: Manual, hand-operated, located at each
tank. One manual and automatic master drain to be
used for Auto Clean and Auto Delime.
BLOWER DRYER: Includes (2) 2 H.P. fan motors
with sealed ball bearings and overload protection.
Available in electric or steam heat.
Page 2 of 12 F40393 – FT1000S Energy Recovery with Blower Dryer Flight-Type Dishwasher
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
FT1000S ENERGY RECOVERY
WITH BLOWER DRYER
FLIGHT-TYPE DISHWASHER
No other control
system allows
easier monitoring.
The digital controls are
placed in a convenient
panel that lets operators verify proper operation and
temperatures at a glance. Digital display indicates
the unit is on, and conrms that the doors are
closed. Automatic door interlocks prevent the pump
and conveyor from operating if the doors are open.
Easy-to-read digital display indicates accurate temperatures of the 160°F wash, 160°F dual rinse and
180°F nal rinse — critical for proper HACCP system
record-keeping.
Stainless steel pump is built for long life.
The stainless steel pump housing and impeller offer
greater durability and long life. The pump motor is
totally enclosed and fan cooled (TEFC) to protect it
from water spray during dishroom clean-up.
Scrap baskets
capture food particles
and are easy to clean.
The sloped screens that
carry scraps to the scrap
baskets are steeper, so less
soil gets into the tanks. The basket
opening is larger for easy cleaning and basket
handles have been designed for easy lift-out access.
The load section also features a removable scrap
basket which contains soil that is pumped from the
ASR section. All scrap baskets and strainers are
stainless steel for strength and durability.
The FT1000
Series saves
water and
energy.
The unit has the
lowest water
and energy
consumption in
the industry, yet
provides effective cleaning and sanitizing that meets
NSF International requirements.
This is achieved through
a carefully balanced ratio
of water ow to pressure.
Insulated doors and thermal
layered curtains also reduce
heat loss. The unit’s 58 gallons
per hour rinse ow rate saves
both water and the energy to
heat it.
Variable speed
conveyor offers
increased
throughput.
The conveyor
on the FT1000
Series is wider
so it can handle
more ware.
Result: more volume and versatility, quicker work.
Its speed is servicer adjustable for the type of ware,
soiled condition, or workforce requirements. It runs at
4 - 6.3 feet per minute.
Energy Recovery system
reclaims heat for energy.
The Energy Recovery
system's heat exchanger
captures escaping heat
and steam from the exhaust
air in the dish machine,
and uses it to preheat the
incoming cold water
supply to 120°F before it
enters the booster heater.
In addition to energy
savings, the Energy Recovery system provides a
viable use for this otherwise exhausted heat.
Self-draining wash pumps help keep water clean.
Pumps are self-draining when the machine is shut
down, so there is no residual water left in the pumps.
Installation is quick and easy with modular design,
minimal wiring connections, and single point vent.
Modular design means
the FT1000 installs quickly
and reliably. The control
panel is already in place,
premounted to the dual
rinse/nal rinse section.
Wiring connections are
minimal, and there is
only a single vent, saving
time and expense. The
control box uses a “single
plane” circuitry design for
easy accessibility during
installation and service.
The FT1000 is ready to
run quickly.
F40393 – FT1000S Energy Recovery with Blower Dryer Flight-Type Dishwasher Page 3 of 12
FT1000S ENERGY RECOVERY
37 1/2"
63 3/8"
FLOOR LINE
7 7/8"3 15/16"
OVER FRAME "A"
62 3/4"
)
6" MINIMUM
ON THE TOP
FLOOR LINE
NOTE: REFER TO LATEST
NO
WITH BLOWER DRYER,
ELECTRIC L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
E1
E2
E3
E4
18 3/4"
E5
E6
E7
E8
P2
P1
P3
V1
P3
V1
E3
E7
5 3/4"
E2
E6
E1
5' 1"
9 15/16"
11 13/16"
25 9/16"
23 3/4"
6" AIR
GAP
25 9/16"
3"
P3
LOAD "B"
124 11/16"
E5
E4
E8
35 7/16" 35 7/16"
60"
52"
44 9/16"
UNLOAD "C"
EXHAUST HOOD
SUPPLIED BY OTHERS
43 5/16"
P2
P1
23 3/4"
55 11/16"
V1
36 1/2"
EDITION OF NATIONAL
ELECTRICAL CODE AND
LOCAL BUILDING CODES
FOR PROPER CLEARANCE
NOTE: STRAINER PANS
REQUIRE 35" TO
BE REMOVED. EXTRA
CLEARANCE SHOULD BE
PROVIDED.
BLOWER/
DRYER
AUX
LOAD
END
6"
35"
ASR
40 3/8"
44 13/16"
SEE NOTE (a)
PRE-
WASH
DIRECTION OF OPERATION
22" HIGH X 29-13/16"
WIDE OPENING WILL
HANDLE 18" X 26" BUN PANS
NOTE: CLEARANCE FROM WALL
24" RECOMMENDED,
WITH DETERGENT DISPENSER
POWER
WASH
RNS
FNL
RNS
MODEL NO.
FT1020S (7.5'-5'-7.5') 20' 4-1/16"
FT1021S (8.5'-5'-7.5') 21' 3-13/16"
FT1022S (9.5'-5'-7.5') 22' 3-21/32"
FT1022S (7.5'-5'-9') 21' 11-13/16"
FT1023S (8.5'-5'-9') 22' 11-9/16"
FT1024S (9.5'-5'-9') 23' 11-13/32"
FT1024S (7.5'-5'-11') 23' 11-7/16"
FT1025S (8.5'-5'-11') 24' 11-3/16"
FT1026S (9.5'-5'-11') 25' 11-1/32"
FT1027S (7.5'-5'-15') 27' 6-3/4"
FT1028S (8.5'-5'-15') 28' 6-1/2"
FT1029S (9.5'-5'-15') 29' 6-11/32"
FT1029S (7.5'-5'-17') 29' 6-5/16"
FT1030S (8.5'-5'-17') 30' 6-1/16"
FT1031S (9.5'-5'-17') 31' 5-29/32"
TE: OVERALL LENGTH OF MACHINE IS DIMENSION "A" + 11 13/16"
UNLOAD
END
36 1/4"
"A""B"
7' 8-1/2"
8' 8-1/4"
9' 8-3/32"
7' 8-1/2"
8' 8-1/4"
9' 8-3/32"
7' 8-1/2"
8' 8-1/4"
9' 8-3/32"
7' 8-1/2"
8' 8-1/4"
9' 8-3/32"
7' 8-1/2"
8' 8-1/4"
9' 8-3/32"
81 7/8"
89 3/8"
SEE NOTE (e
"C"
7' 6-1/2"
7' 6-1/2"
7' 6-1/2"
9' 2-1/4"
9' 2-1/4"
9' 2-1/4"
11' 1-7/8"
11' 1-7/8"
11' 1-7/8"
14' 9-3/16"
14' 9-3/16"
14' 9-3/16"
16' 8-3/4"
16' 8-3/4"
16' 8-3/4"
Page 4 of 12 F40393 – FT1000S Energy Recovery with Blower Dryer Flight-Type Dishwasher
Loading...