Hobart ML-136145, ML-136135 User Manual
I
N
S
T
R
U
C
T
I
O
N
S
MODEL 3813 & 3913 SLICERS
MODELS
3813 Manual Slicer ML-136135
3913 Automatic Slicer ML-136145
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com
FORM 35219 (Oct. 2007)
TABLE OF CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Accessories & Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Product Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Sharpener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Top Knife Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Clean Before Using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Slicing — Model 3813 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Slicing — Model 3913 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cleaning the Knife in Place. . . . . . . . . . . . . . . . . . . . . . . . 8
Using the Knife Removal Tool Accessory . . . . . . . . . . . 10
Reassemble Slicer Parts . . . . . . . . . . . . . . . . . . . . . . . . . 11
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Knife Sharpening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Lubrication — Carriage Slide Rod . . . . . . . . . . . . . . . . . 12
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
© HOBART CORPORATION 2007
– 2 –
Installation, Operation and Care of
MODEL 3813 & 3913 SLICERS
SAVE THESE INSTRUCTIONS
GENERAL
The model 3813 and 3913 slicers are equipped with a 1⁄2 HP motor and are available for single-phase
electrical service. The slicer features the Hobart CleanCut
TM
13" diameter contoured stainless steel
knife. The slicer is furnished with a cord and plug as standard equipment. Other features include:
The No Volt Release feature, standard, requires the slicer to be restarted after a power interruption.
The Gauge Plate Interlock feature, standard, prevents the PRODUCT TRAY (Fig. 1) from being tilted or
removed unless the P
RODUCT TRAY is in the home position (pulled all the way toward you) and the GAUGE
PLATE is closed. Note also that the slicer will not start unless the KNOB on the PRODUCT TRAY SUPPORT
ARM (Fig. 1) is tight.
The Home Start feature, standard, requires the P
RODUCT T RAY (Fig. 1) to be in the home position (pulled
all the way toward you) before the slicer can be started.
The Close-to-Stop feature, standard, turns the slicer off when the GAUGE P LATE is returned to the closed
position by turning the I
NDEX KNOB (Fig. 1) fully clockwise. The slicer also is turned off if the OFF button
is pressed.
The Auto-Shutoff feature, standard, will automatically turn the slicer off if a back-and-forth stroke of
the P
RODUCT TRAY has not been made within 30 seconds.
The Lift Assist feature, standard, allows you to lift and lower the right side of the slicer with little effort
to enable cleaning underneath.
The model 3913 slicer features automatic slicing with a choice of three speeds for the P
The Select-a-Stroke
TM
feature allows you to select the exact stroke length to fit the product being sliced;
RODUCT TRAY.
this can increase the slice rate on items needing a shorter stroke.
ACCESSORIES & OPTIONS
• Fences — Each fence clamps on the P
RODUCT TRAY to limit product movement during slicing.
Two fences are available. The Full Fence is suitable for all products. The End Fence
is for meat or cheese loaves.
Food Chute
•
— Clamps on the PRODUCT TRAY to limit movement of product during slicing (for
tomatoes, onions or similar items).
• Knife — Allows the KNIFE to be removed from the motor hub. After removal, the KNIFE remains
Removal attached to the K
Tool dishwasher. After the removed K
reattach the K
NIFE REMOVAL TOOL while the KNIFE is being cleaned in a sink or
NIFE is cleaned, the KNIFE REMOVAL TOOL is used to
NIFE to the motor hub on the slicer. Refer to pages 10 – 11 for additional
information.
• Deflector — Assists in deflecting sliced product to the platter during slicing. The D
EFLECTOR
(Fig. 16) fits on the DEFLECTOR BRACKET located on the SHARPENER MOUNT.
• 4" Leg Set — Raises the height of the slicer for use on some deli carts. To install: Remove the
slicer feet (two adjacent feet at a time) by unscrewing them. Reinstall the slicer feet
on the bottom of the 4" legs. Install a leg with foot in the two adjacent corners of the
slicer base where the slicer feet were removed. Use the same process for the next
two adjacent feet. There are three alternate corner locations that can be used for the
legs / feet in case the table does not permit use of the standard corners. Assure
proper stability by using only one alternate location for any corner.
– 3 –
INSTALLATION
UNPACKING
Immediately after unpacking the slicer, check for possible shipping damage. If the slicer is found to be
damaged, save the packaging material and contact the carrier within 15 days of delivery.
Prior to installing the slicer, test the electrical service to assure it agrees with the specifications on the
machine data plate. The data plate is located on the left side of the slicer base.
PRODUCT TRAY
The P
RODUCT TRAY (Fig. 1) must be installed.
SHARPENER
GAUGE PLATE
PRODUCT
TRAY
KNOB
SUPPORT
ARM
INDEX
KNOB
To install the PRODUCT TRAY on the slicer,
lower the bottom of the S
UPPORT ARM onto
the CARRIAGE HINGE PINS (Fig. 3). Tilt the
RODUCT T RAY toward the GAUGE P LATE. Press
P
NOB on the SUPPORT ARM, and rotate it in
the K
either direction until the KNOB is against the
UPPORT ARM. Then, turn the KNOB clockwise
S
a quarter turn until snug.
PRODUCT TRAY
TILTED TO THE RIGHT
SUPPORT
ARM
KNOB
Fig. 1
To remove the PRODUCT TRAY, turn the KNOB on the
UPPORT ARM counterclockwise a quarter turn. The
S
NOB is spring-loaded and will pop outward. Tilt the
K
RODUCT TRAY to the right, away from the GAUGE PLATE
P
(Fig. 2). Then hold the PRODUCT TRAY with both hands
and lift upward (Fig. 3).
– 4 –
SUPPORT ARM
Fig. 2
Fig. 3
KNOB
BOTTOM OF
SUPPORT ARM
CARRIAGE
HINGE PIN
Loading...