HMC Electronics ES1696 User Manual

PRODUCT DESCRIPTION

Flux-Off® No Clean “Plus” Flux Remover is
an extra strength solvent that removes heavy
and encrusted flux deposits. This high
pressure aerosol or bulk liquid penetrates
quickly to remove all types of flux, oxide
particles, dust, grease and oil, then evaporates
quickly leaving no residues.
 Powerful cleaner removes R, RA, RMA,

and No Clean fluxes

 Non-corrosive, safe for metals
 Flammable
 Extra-strength
 Fast drying
 Removes encrusted, baked-on fluxes
 All-Way Spray valve - even sprays upside

down

 Available with BrushClean™ System

TYPICAL APPLICATIONS
Flux-Off

®

No Clean “Plus” Flux Remover

effectively cleans flux residues from:

 Chip Carriers
 Heat Sinks
 Metal Housings and Chassis
 Printed Circuit Boards
 Plugs
 Relays and Contacts
 Sockets
 Surface Mount Device Pads
 Solenoids
 Switches

TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES

Flash Point

-20°F

Evaporation Rate >1
(butyl acetate=1)
Specific Gravity 0.706

Appearance Clear, Colorless Liquid

Odor

Ethereal

Solubility in Water

Negligible

Kauri-Butanol
(KB) Number

86

Shelflife 5 years
RoHS/WEEE

Status

COMPATIBILITY

Flux-Off

®

No Clean “Plus” Flux Remover,
like any cleaner, should be tested on a non­critical area to determine plastics
compatibility prior to use. Not recommended
for ABS, acrylics, polycarbonates,
polystyrenes and PVC.

TDS # 1696

CHEMTRONICS

®

Technical Data Sheet

Flux-Off® No Clean “Plus”

Flux Remover

Documentation Provided By HMC Electronics

33 Springdale Ave. Canton, MA 02021

http://www.hmcelectronics.com

[phone]

Material Compatibility

ABS Non-Compatible
Buna-N Non-Compatible
EPDM Excellent
Graphite Excellent
HDPE Excellent
LDPE Good
Lexan™

Non-Compatible
Neoprene Fair
Noryl®

Non-Compatible
Nylon™ 66

Excellent
Cross-Linked PE Excellent
Polypropylene Excellent
Polystyrene Non-Compatible
PVC Non-Compatible
Silicone Rubber Non-Compatible
Teflon™

Excellent
Viton™

Non-Compatible

USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
Spray 4-6” from surface to clean. Wash parts
from top to bottom, allowing the liquid to
flush away flux residue. Flux-Off

®

No Clean
“Plus” can be used to remove all types of
fluxes in an ultrasonic cleaner.

AVAILABILITY
ES1696 12 oz. Aerosol
ES896B 8 oz. BrushClean™ System
ES196 1 Gal. Liquid

TECHNICAL & APPLICATION
ASSISTANCE

ITW Chemtronics

®

provides a technical
hotline to answer your technical and
application related questions. The toll free
number is: 1-800-TECH-401.

ENVIRONMENTAL IMPACT DATA

ENVIRONMENTAL IMPACT DATA

CFC 0.0% VOC 51%
HCFC-141b
HCFC-225

0.0%

0.0%

HFC

nPB

0.0%

0.0%

CFC, HCFC-225, HCFC-141b, VOC, HFC, and nPB
percentages shown are the content by weight.

NOTE:

This information is believed to be accurate. It is
intended for professional end users having the skills
to evaluate and use the data properly. ITW
CHEMTRONICS® does not guarantee the accuracy
of the data and assumes no liability in connection
with damages incurred while using it.

MANUFACTURED BY:

ITW CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888

REV. B (06/06)

DISTRIBUTED BY:

Documentation Provided By HMC Electronics

33 Springdale Ave. Canton, MA 02021

http://www.hmcelectronics.com

[phone]