HMC Electronics ES1035 User Manual
TDS # 1035
PRODUCT DESCRIPTION
The Flux-Off Rosin formulation is a fast
drying aerosol that quickly and completely
removes R, RMA, RA, and synthetic flux
residue. With it’s low surface tension and
superior wetting properties, Flux-Off
Rosin
removes harmful residues in tight tolerance
areas.
Removes R, RMA, RA, and synthetic flux
residues
Penetrates hard to reach areas
Evaporates quickly
Leaves no residue
Removes oil, grease, ionic and non-ionic
residues
Has low odor
Non-corrosive formulation
Contains no CFCs or HCFCs
TYPICAL APPLICATIONS
Flux-Off
Rosin removes flux residues and
cleans:
Chip Carriers
Heat Sinks
Plugs
Printed Circuit Boards
Relays
Sockets
Surface Mount Device Pads
Switches
CHEMTRONICS
Technical Data Sheet
Flux-Off Rosin Flux Remover
TYPICAL PRODUCT DATA AND PHYSICAL
PROPERTIES
Boiling Point
141F Initial
Solubility in Water
20%
Specific Gravity
0.70
Evaporation Rate (butyl acetate=1) >1
Surface Tension
(dynes/cm @21.6C)
17.3
Flash Point (TCC)
-20.0F
Kauri-Butanol (KB) Number 50
VOC* Content: Aerosol Liquid
CARB 75% 100%
SCAQMD 603 g/L 720 g/L
Federal 75% 100
%
RoHS Compliant
Shelflife Aerosols 5 years
Liquids 2 years after opening
*Volatile Organic Compound (VOC) information is calculated on a
weight basis using the VOC definition of California Air Resources
Board (CARB) Consumer Product Regulations, South Coast Air
Quality Management District (SCAQMD) Rule 102 and the Federal
definition published in 40 CFR 51.100(s).
COMPATIBILITY
Flux-Off Rosin is generally compatible with
most materials used in the electronics
industry. With any cleaning agent
compatibility solvent/component must be
determined on a non-critical area prior to use.
Documentation Provided By HMC Electronics
33 Springdale Ave. Canton, MA 02021
http://www.hmcelectronics.com
(800) 482-4440
Material Compatibility
ABS Good
Buna-N Good
EPDM Poor
Graphite Excellent
HDPE Excellent
Kynar
Fair
LDPE Fair
Lexan
Fair
Neoprene Non-Compatible
Noryl
Good
Nylon 66
Excellent
Cross-Linked PE Excellent
Polypropylene Good
Polystyrene Not recommended
PVC Good
Silicone Rubber Not recommended
Teflon
Excellent
Viton
Excellent
Performance
Product Required for Rosin Removal
(mg solvent used to remove 1 mg rosin flux)
Flux-Off Rosin
101
Conventional Flux Remover
3673
Rosin Removal Rate (mg / in2 sec.)
Flux-Off Rosin
4.0
Conventional Flux Remover
0.3
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
Spray 4-6” from surface to clean. Wash parts from
top to bottom, allowing the liquid to flush away dirt
and dissolved grease. For precise application use
attached extension tube. Product is Flammable - Do
not use near sources of ignition and energized
equipment.
TECHNICAL & APPLICATION
ASSISTANCE
ITW Chemtronics provides a technical hotline to
answer your technical and application related
questions. The toll free number is:
1-800-TECH-401.
AVAILABILITY
ES1035 10 oz. Aerosol
ES1035 10 oz. BrushClean Aerosol
ES835B 5 oz. BrushClean Aerosol
ES135 1 gallon Liquid
ES535 5 gallon Liquid
ES5535 53 gallon Liquid
ENVIRONMENTAL IMPACT DATA
HCFC-141b
HCFC-225
None
None
HFC
nPB
Aerosol -Yes
None
Hydrochlorofluorocarbons (HCFCs) are regulated under the Montreal Protocol
as Class II ozone depleting substances. HCFC-141b is no longer produced in the
US under this legislation. HCFC-225 is planned for production phase-out in
2015. Hydrofluorocarbons (HFCs) are not currently regulated.
EPA has listed n-propyl bromide (nPB) as an acceptable alternative to ozone
depleting substances in metal, precision, and electronics cleaning under Section
612 of the Clean Air Act.
NOTE: This information is believed to be accurate.
It is intended for professional end users having the
skills to evaluate and use the data properly. ITW
CHEMTRONICS
does not guarantee the accuracy
of the data and assumes no liability in connection
with damages incurred while using it.
Chemtronics and Flux-Off are registered trademarks of
ITW Chemtronics. All rights reserved.
All other trademarks herein are trademarks or registered
trademarks of their respective owners.
MANUFACTURED BY:
ITW CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888 REV. B (06/09)
DISTRIBUTED BY:
Documentation Provided By HMC Electronics
33 Springdale Ave. Canton, MA 02021
http://www.hmcelectronics.com
(800) 482-4440
Loading...