HMC Electronics ES1020 User Manual
PRODUCT DESCRIPTION
Ultrajet® compressed gas duster is a high
pressure duster that cleans electronics
without scratching delicate surfaces. This
duster/ cleaner is nonflammable, residue-free
and won’t scratch delicate surfaces.
Filtered to 0.2 microns
Nonflammable
Leaves no residue
High pressure for contamination control
Nonabrasive
Excellent material compatibility
Penetrates hard to reach areas
Contains no ozone depleting compounds
TYPICAL APPLICATIONS
Ultrajet
®
duster is engineered for all aspects
of electronic equipment maintenance and is
particularly suited for applications involving:
Audio/Video Equipment
Computers and Other Electronic
Equipment
Fax Machines
Laboratory Instruments
Photo Equipment
Printed Circuit Boards
Printers
Surface Mount Devices
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Boiling Point -15.7°F
Vapor Density (air=1)
@ 77°F
3.18
Solubility in Water
@ 77°F F/1 atm
0.10% by weight
Specific Gravity
(water = 1 @77°F)
1.21
Evaporation Rate >1
(butyl acetate=1)
Appearance Clear, Colorless
Liquified Gas
Odor
Slight Ethereal
Surface Tension
(dynes/cm @77°F)
7.8
Flash Point (TCC)
None
Shelflife 5 years
RoHS/WEEE
Status
COMPATIBILITY
Ultrajet
®
is generally compatible with most
materials used in printed circuit board
fabrication, including sensitive plastics and
compounds. As with any duster/cleaner,
compatibility must be determined on a noncritical area prior to use.
TDS # 1020
CHEMTRONICS
®
Technical Data Sheet
Ultrajet
®
Documentation Provided By HMC Electronics
33 Springdale Ave. Canton, MA 02021
http://www.hmcelectronics.com
(800) 482-4440
Material Compatibility
Buna-N Excellent
Graphite Excellent
HDPE Excellent
LDPE Excellent
Lexan™
Excellent
Neoprene Excellent
Cross-Linked PE Excellent
Polyacrylate Excellent
Polystyrene Excellent
PVC Excellent
Silicone Rubber Excellent
Teflon™
Excellent
Viton™
Excellent
PERFORMANCE
Pressure PSIG / Temperature F
200
-
P
150
S
-
I
100
G
-
50
-
0
20 40 60 80 100 120 140
Temperature F
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
No special surface preparation is required
prior to using Ultrajet
®
. Direct high pressure
spray onto the area to be cleaned to remove
dust, dirt and other contaminant. For
optimum performance and pin point control,
use with the attached extension tube.
AVAILABILITY
ES1020 10 oz. Aerosol
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics
®
provides a technical hotline to
answer your technical and application related
questions. The toll free number is:
1-800-TECH-401
.
ENVIRONMENTAL IMPACT DATA
ENVIRONMENTAL IMPACT DATA
CFC 0.0% VOC 0.0%
HCFC 0.0% HFC 100.0%
CL Solv. 0.0% ODP 0.00
CFC, HCFC, CL. SOLV., VOC, and HFC numbers
shown are the content by weight. Ozone depletion
potential (ODP) is determined in accordance with the
Montreal Protocol and U.S. Clean Air Act of 1990. The
ODP of this product is 0.0. It is the sum of the ODP of
the substances that may contribute to the depletion of
stratospheric ozone, based upon the weight of each
substance in the product’s formulation.
NOTE:
This information is believed to be accurate. It is intended
for professional end users having the skills to evaluate
and use the data properly. CHEMTRONICS
®
does not
guarantee the accuracy of the data and assumes no
liability in connection with damages incurred while using
it.
MANUFACTURED BY:
ITW CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888 REV. D(06/06)
DISTRIBUTED BY:
Documentation Provided By HMC Electronics
33 Springdale Ave. Canton, MA 02021
http://www.hmcelectronics.com
(800) 482-4440
Loading...