Hitachi RAS-S24HPA, RAC-S24HPA Instruction Manual

– 1 –

ENGLISH

INDOOR UNIT/OUTDOOR UNIT

MODEL

RAS-S24HPA(EG)/RAC-S24HPA(EG)

OUTDOOR UNIT INDOOR UNIT

Instruction manual Page 1~24 To obtain the best performance and ensure years of trouble free use, please read this instruction manual completely.

SPLIT TYPE AIR CONDITIONER

RAS-S24HPA(EG)

RAC-S24HPA(EG)

(EN1) RAS-S24HPA (EG) 1(EN1) RAS-S24HPA (EG) 1 1/15/14 4:40 PM1/15/14 4:40 PM

– 2 –

!

SAFETY PRECAUTION

WARNING

PRECAUTIONS DURING INSTALLATION

●

Do not reconstruct the unit.

Water leakage, fault, short circuit or ﬁ re may occur if you reconstruct

the unit by yourself.

●

Please ask your sales agent or qualiﬁ ed technician for the installation

of your unit. Water leakage, short circuit or ﬁ re may occur if you install the unit by yourself.

●

Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor,

or the earth line of telephone. Improper installation of earth line may cause electric shock.

●

A circuit breaker should be installed depending on the mounting site of

the unit. Without a circuit breaker, the danger of electric shock exists.

●

Do not install the unit near a location where there is ﬂ ammable gas.

The outdoor unit may catch ﬁ re if ﬂ ammable gas leaks around it.

●

Please ensure smooth ﬂ ow of water when installing the drain hose.

CAUTION

!

PRECAUTIONS DURING OPERATION

●

Avoid an extended period of direct air ﬂ ow for your health.

W

A R N

I

N

G

!

●

Do not insert a ﬁ nger, a rod or other objects into the air outlet or inlet. As the fan

is rotating at a high speed, it will cause injury. Before cleaning, be sure to stop the operation and turn the breaker OFF.

●

During thunder storm, disconnect and turn off the circuit breaker.

●

Do not use any conductor as fuse wire, this could cause fatal accident.

!

Make sure to connect earth line.

Indicates the instructions that must be followed.

The sign in the ﬁ gure indicates prohibition.

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

●

Should abnormal situation arises (like burning smell), please stop operating the unit

and turn off the circuit breaker. Contact your agent. Fault, short circuit or ﬁ re may occur if you continue to operate the unit under abnormal situation.

●

Please contact your agent for maintenance. Improper self maintenance may cause

electric shock and ﬁ re.

●

Please contact your agent if you need to remove and reinstall the unit. Electric

shock or ﬁ re may occur if you remove and reinstall the unit yourself improperly.

●

If the supply cord is damaged, it must be replaced by the special cord

obtainable at authorized service/parts centers.

W

A R N

I

N

G

!

●

Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

●

Pay special attention to signs of “ Warning” and “ Caution”. The “Warning” section contains matters which, if not observed strictly, may cause death or serious injury. The “Caution” section contains matters which may result in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

●

The sign indicate the following meanings.

●

Please keep this manual after reading.

(EN1) RAS-S24HPA (EG) 2(EN1) RAS-S24HPA (EG) 2 1/15/14 4:40 PM1/15/14 4:40 PM

– 3 –

ENGLISH

PRECAUTIONS DURING OPERATION

●

Do not attempt to operate the unit with wet hands, this could cause fatal

accident.

●

When operating the unit with burning equipments, regularly ventilate the

room to avoid oxygen insufﬁ ciency.

●

Do not direct the cool air coming out from the air-conditioner panel to face

household heating apparatus as this may affect the working of apparatus such as the electric kettle, oven etc.

●

Do not use any aerosol or hair sprays near the indoor unit. This chemical

can adhere on heat exchanger ﬁ n and blocked the evaporation water ﬂ ow to drain pan. The water will drop on tangential fan and cause water splashing

out from indoor unit.

●

Please ensure that outdoor mounting frame is always stable, ﬁ rm and

without defect. If not, the outdoor unit may collapse and cause danger.

●

Do not splash or direct water to the body of the unit when cleaning it as

this may cause short circuit.

●

When operating the unit with the door and windows opened, (the room humidity is always above

80%) and with the air deﬂ ector facing down or moving automatically for a long period of time, water will condense on the air deﬂ ector and drips down occasionally. This will wet your furniture. Therefore, do not operate under such condition for a long time.

●

If the amount of heat in the room is above the cooling or heating capability of the unit (for

example: more people entering the room, using heating equipments and etc.), the preset room temperature cannot be achieved.

●

This appliance is not intended for use by young children or inﬁ rm persons unless they have

been adequately supervised by a responsible person to ensure that they can use the appliance safely.

●

Young children should be supervised to ensure that they do not play with the appliance.

●

Do not climb on the outdoor unit or put objects on it.

●

Please switch off the unit and turn off the circuit breaker during cleaning,

the high-speed fan inside the unit may cause danger.

●

Turn off the circuit breaker if the unit is not to be operated for a long period.

C A U T

I O N

!

●

The product shall be operated under the manufacturer speciﬁ cation and

not for any other intended use.

●

Do not put water container (like vase) on the indoor unit to avoid water

dripping into the unit. Dripping water will damage the insulator inside the unit and causes short-circuit.

●

Do not place plants directly under the air ﬂ ow as it is bad for the plants.

(EN1) RAS-S24HPA (EG) 3(EN1) RAS-S24HPA (EG) 3 1/15/14 4:40 PM1/15/14 4:40 PM

– 4 –

INDOOR UNIT

NAMES AND FUNCTIONS OF EACH PART

Air ﬁ lter

To prevent dust from coming into the indoor unit. (Refer page 18)

Front panel

Indoor unit indicators

Light indicator showing the operating condition. (Refer page 5)

Horizontal deﬂ ector

●

Vertical deﬂ ector

(Air Outlet)

(Refer page 13)

Remote controller

Send out operation signal to the indoor unit. So as to operate the whole unit. (Refer page 6)

OUTDOOR UNIT

Drain pipe

Condensed water drain to outside.

Connecting cord and insulation pipe for piping

Air inlet (Back and Left side)

Air outlet

WIDTH (mm)

900

850

MODEL

RAS-S24HPA(EG)

RAC-S24HPA(EG)

HEIGHT (mm)

300

650

DEPTH (mm)

230

298

MODEL NAME AND DIMENSIONS

(EN1) RAS-S24HPA (EG) 4(EN1) RAS-S24HPA (EG) 4 1/15/14 4:40 PM1/15/14 4:40 PM

– 5 –

ENGLISH

INDOOR UNIT INDICATORS

TEMPORARY SWITCH

Use this switch to start and stop when the remote controller does not work.

Normal operation:

● By pressing the temporary switch, the operation is done in previously set operation mode.

● When the operation is done using the temporary switch after the power source is turned off and turn

on again, the operation is done in automatic mode.

Force cooling operation: (For servicing purpose only)

● By pressing and hold the temporary switch for more than 5 second, the unit will enter “Force Cooling

Operation”.

● Press again the temporary switch to cancel the force cooling operation.

● Do not operate in this mode for more than 5 minutes.

*

To be conduct by authorised personel only.

OPERATION INDICATOR

FILTER LAMP

When the device is operated for a total of about 200 hours, the FILTER lamp lights to indicate that it is time to clean the ﬁ lter. The lamp goes out when the “ (AUTO SWING)” button is pressed while the device is on “STANDBY MODE”.

OPERATION LAMP

This lamp lights during operation. The OPERATION LAMP ﬂ ashes in the following cases during heating.

(1) During preheating

For about 2–3 minutes after starting up.

(2) During defrosting

Defrosting will be performed about once every one

hour when frost forms on the heat exchanger of the outdoor unit, for 5–10 minutes each time.

TIMER LAMP

This lamp lights when the timer is working.

(EN1) RAS-S24HPA (EG) 5(EN1) RAS-S24HPA (EG) 5 1/15/14 4:40 PM1/15/14 4:40 PM

– 6 –

NAMES AND FUNCTIONS OF REMOTE CONTROL UNIT

REMOTE CONTROLLER

This controls the operation of the indoor unit. The range of control is about 7 meters. If indoor lighting is controlled electronically, the range of control may be shorter. This unit can be ﬁ xed on a wall using the ﬁ xture provided. Before ﬁ xing it, make sure the indoor unit can be controlled from the remote controller.

● Transmission sign

The transmission sign blinks when a signal is sent.

● Display

This indicates the room temperature selected, timer status, function

and intensity of circulation selected.

● HEATING button

Use this button to set heating mode in the room or start operation.

● DEHUMIDIFYING button

Use this button to reduce humidity in the room or start operation.

● COOLING button

Use this button to set cooling mode in the room or start operation.

● RESET button

● SUPER COOLING button

Use this button to set super cooling operation or start operation

(cooling function only).

● STOP button

Press this button to stop operation only.

● PARALLEL SWING button

Controls the angle of the vertical air deﬂ ectors to parallel.

● FAN SPEED selector

This determines the fan speed. Every time you press this button,

the intensity of circulation will change from (AUTO) to (HI) to (MED) to (LOW).

● AUTO SWING button

Controls the angle of the horizontal air deﬂ ector.

● TEMPERATURE button

Use this button to raise or lower the temperature setting. (Keep

pressed, and the value will change more quickly.)

● SLEEP button

Use this button to set the sleep timer.

● ON-TIMER button Select to turn ON time.

Precautions for Use

● Do not put the remote controller in the following places.

● In direct sunlight.

● In the vicinity of a heater.

● Handle the remote controller carefully. Do not drop it on the

ﬂ oor, and protect it from water.

● Once the outdoor unit stops, it will not restart for about 3

minutes (unless you turn the power switch off and on or unplug the power cord and plug it in again).

This is to protect the device and does not indicate a failure.

(EN2) RAS-S24HPA (EG) 6(EN2) RAS-S24HPA (EG) 6 1/15/14 4:40 PM1/15/14 4:40 PM

– 7 –

ENGLISH

HEATING OPERATION

● Use the device for heating when the outdoor temperature is under 21°C.

When it is too warm (over 21°C), the heating function may not work in order to protect the device.

Press the FUNCTION selector so that the display indicates (HEAT).

Set the desired FAN SPEED with the (FAN SPEED) button (the display indicates the setting). (AUTO) : The fan speed is HI at first and varies to

MED or LOW automatically when the preset temperature has been reached.

(HI) : Economical as the room will become warm

quickly.

But you may feel a chill at the beginning.

(MED) : Quiet.

(LOW) : More quiet.

Set the desired room temperature with the TEMPERATURE buttons (the display indicates the setting).

The range of 18-22°C is recommended as the room temperature for heating. If the temperature setting is 20°C, the room temperature will be controlled at around 20°C.

The temperature setting and the actual room temperature may vary somewhat depending on conditions.

Press the (START/STOP) button. Heating operation starts with a beep. Press the button again to stop operation.

■ As the settings are stored in memory in the remote controller, you

only have to press the (START/STOP) button next time.

1

2

3

START

STOP

(EN2) RAS-S24HPA (EG) 7(EN2) RAS-S24HPA (EG) 7 1/15/14 4:40 PM1/15/14 4:40 PM

– 8 –

DEHUMIDIFYING OPERATION

Use the device for dehumidifying when the room temperature is over 16°C. When it is under 15°C, the dehumidifying function will not work.

■ Dehumidifying Function

When the room temperature is higher than the temperature setting: The device will dehumidify the room, reducing the room temperature to the preset level. When the room temperature is lower than the temperature setting: Dehumidifying will be performed at the temperature setting slightly lower than the current room temperature, regardless of the temperature setting. The function will stop (the indoor unit will stop emitting air) as soon as the room temperature becomes lower than the setting temperature.

■ As the settings are stored in memory in the remote controller, you

only have to press the (DEHUMIDIFY) button next time.

Set the desired room temperature with the TEMPERATURE button (the display indicates the setting).

The range of 20-26˚C is recommended as the

room temperature for dehumidifying.

2

Press the button so that the display indicates

(DEHUMIDIFY). Dehumidifying operation starts with a beep. The FAN SPEED is set at LOW automatically. The FAN SPEED button does not work.

1

Press the (STOP) button to stop operation.

STOP

(EN2) RAS-S24HPA (EG) 8(EN2) RAS-S24HPA (EG) 8 1/15/14 4:40 PM1/15/14 4:40 PM

– 9 –

ENGLISH

COOLING OPERATION

Use the device for cooling when the outdoor temperature is 21-52°C. If indoor humidity is very high (over 80%), some dew may form on the air outlet grille of the indoor unit.

Press the button so that the display indicates

(COOL). Cooling operation starts with a beep. The cooling function does not start if the temperature setting is higher than the current room temperature (even though the

(OPERATION) lamp lights). The cooling function will start as soon as you set the temperature below the current room temperature.

Set the desired FAN SPEED with the

(FAN SPEED) button

(the display indicates the setting).

(AUTO) : The FAN SPEED is HI at ﬁ rst and varies to

MED or LOW automatically when the preset temperature has been reached.

(HI) : Economical as the room will become cool quickly.

(MED) : Fan speed slow.

(LOW) : Fan speed slower.

Set the desired room temperature with the TEMPERATURE button (the display indicates the setting).

The range of 25-28°C is recommended as the room temperature for cooling. If the temperature setting is 27°C, the room temperature will be controlled at around 27°C.

The temperature setting and the actual room temperature may vary somewhat depending on conditions.

Press the (STOP) button to stop operation.

■ As the settings are stored in memory in the remote controller, you

only have to press the (COOLING) button next time.

1

2

STOP

3

(EN2) RAS-S24HPA (EG) 9(EN2) RAS-S24HPA (EG) 9 1/15/14 4:40 PM1/15/14 4:40 PM

– 10 –

SUPER COOLING

Press the button.

● Operation start with a signal received sound “beep”.

● Unit will be forced operate in (COOL) with SUPER HI fan

speed.

Indicator appear during this period while temperature and fan speed setting display remain unchanged. (Operation lamp at indoor unit is blinking).

● Air blow sound will be slightly high due to forced operation.

1

NOTE

(1) ON TIME setting : SUPER COOLING operation will be

a priority over the ON timer operation time.

CANCELLATION of SUPER COOLING Operation

Cancel Condition

Operation mode after cancel

Press or OFF timer time is up

Stop operation

key press

DEHUMIDIFYING operation

Press or

Normal COOLING operation

key press

Press SLEEP operation

HEATING operation

COOLING operation (SLEEP Mode)

(EN2) RAS-S24HPA (EG) 10(EN2) RAS-S24HPA (EG) 10 1/15/14 4:40 PM1/15/14 4:40 PM

– 11 –

ENGLISH

HOW TO SET THE SLEEP TIMER

Press the (SLEEP) button, and the display changes as shown below.

Mode

Sleep timer

Indication

1 hour interval

1 hour 2 hours 11 hours 12 hours

Sleep timer off

44 44

1

Sleep Timer: The device will continue working for the designated number of hours and then turn off. Point the signal window of the remote controller toward the indoor unit, and press the SLEEP button. The timer information will be displayed on the remote controller. The TIMER lamp lights with a beep from the indoor unit. When the sleep timer has been set, the display indicates the turn-off time.

SLEEP

(EN2) RAS-S24HPA (EG) 11(EN2) RAS-S24HPA (EG) 11 1/15/14 4:40 PM1/15/14 4:40 PM

– 12 –

HOW TO SET THE TIMER

■ ON Timer are available.

ON TIME setting

● Select the ON TIMER by pressing the (ON)

Button.

● Setting time will change according to the below

sequence.

ON Timer Reservation

■ Operation will start for setting temperature at setting time (The starting time may differ depending on the room temperature and set temperature).

(EN2) RAS-S24HPA (EG) 12(EN2) RAS-S24HPA (EG) 12 1/15/14 4:40 PM1/15/14 4:40 PM

– 13 –

ENGLISH

Adjustment of the conditioned air in the upward and downward directions. According to “Dehumidifying” or “Cooling” operation, the horizontal air deﬂ ector is automatically set to the proper angle suitable for each operation. The deﬂ ector can be swing up and down and also set to the desired angle using the “ (AUTO SWING)” button. (If the angle of the deﬂ ector is changed, it will not return to the auto- set position after operations start unless the operation mode is switched.)

ADJUSTING THE AIR DEFLECTORS

1

● If the “ (AUTO SWING)” button is pressed once,

the horizontal air deﬂ ector swings up and down. If the button is pressed again, the deﬂ ector stops in its current position. Several seconds (about 6 seconds) may be required before the deﬂ ector starts to move.

● In “Cooling” operation, do not keep the horizontal air

deﬂ ector swinging for a long time. Some dew may form

on the horizontal air deﬂ ector and dew may drop.

2

Adjustment of the conditioned air in the left and right directions.

● If the “ (PARALLEL SWING)” button is pressed

once, the vertical air deﬂ ectors swing left and right to parallel. If the button is pressed again, the deﬂ ectors stop in their current position. Several second (about 6 seconds) may be required before the deﬂ ectors start to move.

● PARALLEL SWING

(EN2) RAS-S24HPA (EG) 13(EN2) RAS-S24HPA (EG) 13 1/15/14 4:40 PM1/15/14 4:40 PM

– 14 –

HOW TO EXCHANGE THE BATTERIES IN THE REMOTE CONTROLLER

1

Remove the cover as shown in the ﬁ gure and take out the old batteries.

=

2

Install the new batteries. The direction of the batteries should match the marks in the case.

1. Do not use new and old batteries, or different kinds of batteries together.

2. Take out the batteries when you do not use the remote controller for 2 or 3 months.

3. Use high quality and high performance AAA batteries to avoid short operating life and electrolyte leakages

CAUTION

!

When using the remote control, if there is no response from the air conditioner unit and or the remote control has fading and dim displays, the batteries in the remote control device need to be removed and replaced with new ones

(EN3) RAS-S24HPA (EG) 14(EN3) RAS-S24HPA (EG) 14 1/15/14 4:41 PM1/15/14 4:41 PM

– 15 –

ENGLISH

Suitable Room Temperature Install curtain or blinds

Ventilation Effective Usage Of Timer

Do Not Forget To Clean The Air Filter

Please Adjust Suitable Temperature

For Baby And Children

Warning

Freezing temperature is bad for health and a waste of electric power.

!

It is possible to reduce heat entering the room through windows.

At night, please use the “OFF or ON timer operation mode”, together with your wake up time in the morning. This will enable you to enjoy a comfortable room temperature. Please use the timer effectively.

Dusty air ﬁ lter will reduce the air volume and the cooling efﬁ ciency. To prevent from wasting electric energy, please clean the ﬁ lter every 2 weeks.

Please pay attention to the room temperature and air ﬂ ow direction when operating the unit for baby, children and old folks who have difﬁ culty in movement.

Caution

Do not close the room for a long period of time. Occasionally open the door and windows to allow the entrance of fresh air.

!

THE IDEAL WAYS OF OPERATION

(EN3) RAS-S24HPA (EG) 15(EN3) RAS-S24HPA (EG) 15 1/15/14 4:41 PM1/15/14 4:41 PM

– 16 –

FOR USER’S INFORMATION

The Air Conditioner And The Heat Source In The Room

Not Operating For A Long Time

When Lightning Occurs

Caution

If the amount of heat in the room is above the cooling capability of the air conditioner (for example: more people entering the room, using heating equipments and etc.), the preset room temperature cannot be achieved.

!

When the indoor unit is not to be used for a long period of time, please switch off the power from the mains. If the power from mains remains “ON”, the indoor unit still consumes about 5W in the operation control circuit even if it is in “OFF” mode.

!

Interference From Electrical Products

!

Warning

To protect the whole unit during lightning, please stop operating the unit and remove the plug from the socket.

Caution

To avoid noise interference, please place the indoor unit and its remote controller at least 1m away from electrical products.

(EN3) RAS-S24HPA (EG) 16(EN3) RAS-S24HPA (EG) 16 1/15/14 4:41 PM1/15/14 4:41 PM

– 17 –

ENGLISH

ATTACHING THE AIR CLEANSING FILTERS

1

Open the front panel.

● Pull up the front panel by holding it at both sides

with both hands.

2

Remove the ﬁ lter.

● Push upward to release the claws and pull out the

ﬁ lter.

3

4

Attach the ﬁ lters.

● Attach the ﬁ lters by ensuring that the surface written

“FRONT” is facing front.

● After attaching the ﬁ lters, push the front panel at

three arrow portion as shown in ﬁ gure and close it.

Cleaning and maintenance must be carried out only by qualiﬁ ed service personal. Before cleaning, stop operation and switch off the power supply.

CAUTION

!

CAUTION

NOTE



Claws

(4 places)

Attaching the air cleansing ﬁ lters to the ﬁ lter.

● Attach the air cleansing ﬁ lters to the frame by gently

compress its both sides and release after insertion into ﬁ lter frame.

Do not bend the air cleansing ﬁ lter as it may cause damage to the structure.

● In case of removing the air cleansing ﬁ lters, please follow the above procedures.

● The cooling capacity is slightly weakened and the cooling speed becomes slower when the air

cleansing ﬁ lters are used. So, set the fan speed to "HIGH" when using it in this condition.

● Air cleansing ﬁ lters are not washable. It is recommended to use vacuum to clean it. It can be use

for 1 year time. Type number for this air cleansing ﬁ lter is <SPX-CFH22>. Please use this number for ordering when you want to change it.

● Do not operate the air conditioner without ﬁ lter. Dust may enter the air conditioner and fault may

occur.

(EN3) RAS-S24HPA (EG) 17(EN3) RAS-S24HPA (EG) 17 1/15/14 4:41 PM1/15/14 4:41 PM

– 18 –

MAINTENANCE

Cleaning and maintenance must be carried out only by qualiﬁ ed service personal. Before cleaning, stop operation and switch off the power supply.

1. AIR FILTER

Clean the air ﬁ lter, as it removes dust inside the room. In case the air ﬁ lter is full of dust, the air ﬂ ow will decrease and the cooling capacity will be reduced. Further, noise may occur. Be sure to clean the ﬁ lter following the procedure below.

!

CAUTION

1

Open the front panel and remove the ﬁ lter

● Gently lift and remove the air cleansing ﬁ lter

from the air ﬁ lter frame.

2

3

● Re-insert the air cleansing ﬁ lter to the ﬁ lter

frame. Set the ﬁ lter with “FRONT” mark facing front, and slot them into the original state.

● After attaching the ﬁ lters, push the front panel

at three arrow portions as shown in ﬁ gure and close it.

!

CAUTION

● Do not wash with hot water at more than 40°C. The ﬁ lter may shrink.

● When washing it, shake off moisture completely and dry it in the shade; do not expose it directly

to the sun. The ﬁ lter may shrink.

● Do not use detergent on the air cleansing ﬁ lter as some detergent may deteriorate the ﬁ lter

electrostatic performance.



Vacuum dust from the air ﬁ lter and air cleansing ﬁ lter using vacuum cleaner. If there is too much dust, rinse under running tap water and gently brush it with soft bristle brush. Allow ﬁ lters to dry in shade.

NOTE:

● Air cleansing ﬁ lter should be cleaned every month or sooner if noticeable loading occurs. When

used overtime, it may loose its deodorizing function. For maximum performance, it is recommended to replace it every 1 year depending on application requirements.

(EN3) RAS-S24HPA (EG) 18(EN3) RAS-S24HPA (EG) 18 1/15/14 4:41 PM1/15/14 4:41 PM

– 19 –

ENGLISH

2. Washable Front Panel

● Remove the front panel and wash with clean water.

Wash it with a soft sponge. After using neutral detergent, wash thoroughly with

clean water.

● When front panel is not removed, wipe it with a

soft dry cloth. Wipe the remote controller thoroughly with a soft dry cloth.

● Wipe the water thoroughly.

If water remains at indicators or signal receiver of

indoor unit, it causes trouble.

Method of removing the front panel. Be sure to hold the front panel with both hands

to detach and attach it.

!

CAUTION

● Do not splash or direct water to the body of the unit when cleaning it as

this may cause short circuit.

● Never use hot water (above 40°C), benzine, gasoline, acid, thinner or a

brush, because they will damage the plastic surface and the coating.

Removing the Front Panel

Arm

● When the front panel is fully opened with both

hands, push the right arm to the inside to release it, and while closing the front panel slightly, put it out forward.

Attaching the Front Panel

● Move the projections of the left and right

arms into the Flanges in the unit and securely insert them into the holes.

3. MAINTENANCE AT BEGINNING OF LONG OFF PERIOD

● Run the unit by setting the operation mode to (COOL),

the temperature to 32°C and the fan speed to HI for about half a day on a ﬁ ne day, and dry the whole of the unit.

● Switch off the power plug.

(EN3) RAS-S24HPA (EG) 19(EN3) RAS-S24HPA (EG) 19 1/15/14 4:41 PM1/15/14 4:41 PM

– 20 –

1

2

3

REGULAR INSPECTION

PLEASE CHECK THE FOLLOWING POINTS BY QUALIFIED SERVICE PERSONNEL EITHER EVERY HALF YEARLY OR YEARLY. CONTACT YOUR SALES AGENT OR SERVICE SHOP.

Is the earth line disconnected or broken?

Is the mounting frame seriously affected by rust and is the outdoor unit tilted or unstable?

Is the plug of power line ﬁ rmly plugged into the socket? (Please ensure no loose contact between them).

Cleaning and maintenance must be carried out only by qualiﬁ ed service personnel. Before cleaning, stop operation and switch off the power supply.

!

CAUTION

● Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the earth

line of telephone. Improper installation of earth line may cause electric shock.

!

● A circuit breaker should be installed depending on the mounting site of the unit. Without a circuit

breaker, the danger of electric shock exists.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code: Green-and-yellow : Earth Blue : Neutral Brown : Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

NOTE

If the supply cord is damaged, it must be replaced by the special cord obtainable at authorized service/parts centers.

(EN3) RAS-S24HPA (EG) 20(EN3) RAS-S24HPA (EG) 20 1/15/14 4:41 PM1/15/14 4:41 PM

– 21 –

ENGLISH

AFTER SALE SERVICE AND WARRANTY

WHEN ASKING FOR SERVICE, CHECK THE FOLLOWING POINTS

When it does not operate

● Is the fuse all right?

● Is the voltage extremely high or low?

● Is the circuit breaker “ON”?

● Was the air ﬁ lter cleaned?

● Does sunlight fall directly on the outdoor unit?

● Is the air ﬂ ow of the outdoor unit obstructed?

● Are the doors or windows opened, or is there any source

of heat in the room?

● Is the set temperature suitable?

CONDITION CHECK THE FOLLOWING POINTS

Notes

● In quiet or stop operation, the following phenomena may occassionally

occur, but they are not abnormal for the operation.

(1) Slight ﬂ owing noise of refrigerant in the refrigerating cycle. (2) Slight rubbing noise from the fan casing which is cooled and then

gradually warmed as operation stops.

● The odor will possibly be emitted from the room air conditioner because

the various odor, emitted by smoke, foodstuffs, cosmetics and so on, sticks to it. So the air ﬁ lter and the evaporator regularly must be cleaned to reduce the odor.

● Please contact your sales agent immediately if the air conditioner still fails to operate normally after the above

inspections. Inform your agent of the model of your unit, production number, date of installation. Please also inform him regarding the fault.

● Power supply shall be connected at the rated voltage, otherwise the unit will be broken or could not reach

the speciﬁ ed capacity.

When it does not cool well

Please note: On switching on the equipment, particularly when the room light is dimmed, a slight brightness ﬂ uctuation may occur. This is of no consequence. The conditions of the local Power Supply Companies are to be observed.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualiﬁ ed person in order to avoid a hazard.

NOTE:

(EN3) RAS-S24HPA (EG) 21(EN3) RAS-S24HPA (EG) 21 1/15/14 4:41 PM1/15/14 4:41 PM

– 22 –

This product conforms with the protection requirements of council directives 89/336/EEC relating to electromagnetic compatibility and 73/23/EEC relating to electrical equipment designed for use within certain voltage limits.

MEMO

......................................................................................................................................................................................

Minimum Maximum Minimum Maximum Indoor Dry bulb °C 21 32 20 24 Wet bulb °C 15 23 12 19 Outdoor Dry bulb °C 21 52 2 21

Wet bulb °C 15 31 1 15.5

Note

● Avoid to use the room air conditioner for cooling operation when the outside temperature is below

21°C (70°F).

The recommended maximum and minimum operating temperatures of the hot and cold sides

should be as below:

Cooling Heating

(EN3) RAS-S24HPA (EG) 22(EN3) RAS-S24HPA (EG) 22 1/15/14 4:41 PM1/15/14 4:41 PM

– 23 –

ENGLISH

MEMO

......................................................................................................................................................................................

(EN3) RAS-S24HPA (EG) 23(EN3) RAS-S24HPA (EG) 23 1/15/14 4:41 PM1/15/14 4:41 PM

– 24 –

SPECIFICATIONS

POWER SOURCE

COOLING CAPACITY

TOTAL INPUT

TOTAL AMPS

EER (Btu/hr.watt)

COOLING CAPACITY

TOTAL INPUT

TOTAL AMPS

EER (Btu/hr.watt)

HEATING CAPACITY

TOTAL INPUT

TOTAL AMPS

WEIGHT (kg)

INDOOR UNIT

OUTDOOR UNIT

RAS-S24HPA(EG)

RAC-S24HPA(EG)

1 Ø, 220-(230)-240V, 50Hz

CONDITION: (T3) ROOM AIR TEMP.

29/19°C (DB/WB) OUTSIDE TEMP. 46/24°C (DB/WB)

CONDITION: (T1) ROOM AIR TEMP.

27/19°C (DB/WB) OUTSIDE TEMP. 35/24°C (DB/WB)

CONDITION:

ROOM AIR TEMP.

20/15°C (DB/WB) OUTSIDE TEMP.

7/6°C (DB/WB)

5.68kW

(19,390Btu/hr)

2,880W

12.4A

6.73

7.04kW

(24,020Btu/hr)

2,265-2,400W

10.8-10.5A

10.61-10.01

7.05kW

(24,060Btu/hr)

2,365-2,540

11.4-11.2A

INDOOR

OUTDOOR

REFRIGERANT (R22)

CHARGING

VOLUME

UNIT

PIPES

FLARE COUPLING TYPE

MAXIMUM LENGTH: 15m

11

52

1,640g

MODEL

(EN3) RAS-S24HPA (EG) 24(EN3) RAS-S24HPA (EG) 24 1/15/14 4:41 PM1/15/14 4:41 PM