Hitachi RAS-S18CPX, RAC-S18CPX Instruction Manual

Instruction manual Page 1~22

To obtain the best performance and ensure years of trouble free use, please read this instruction manual completely.

تﺎﻤﻴﻠﻌﺘﻟا ﺐﻴﺘﻛ٢٢-١ ص

ﻮـﻃ ةﺪﳌ زﺎﻬﳉا لﺎﻤﻌﺘﺳا ﻦﻜﳝ ﻲﻜﻟعﻼﻃﻹا ﺐﺠﻳ ﺐﻄﻋ نوﺪﺑ ﺔﻠﻳ

.اﺪﻴﺟ ﺐﻴﺘﻜﻟا اﺬﻫ ﻰﻠﻋ

SPLIT TYPE

INDOOR UNIT/OUTDOOR UNIT

MODEL

RAS-S18CPX/RAC-S18CPX

INDOOR UNIT

OUTDOOR UNIT

RAC-S18CPX

RAS-S18CPX

RAS/RAC S18CPX(ENG COVER) 10/26/08, 4:59 PM1

Black

– 2 –

!

SAFETY PRECAUTION

●

Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

●

Pay special attention to signs of “ Warning” and “ Caution”. The “Warning” section contains matters which, if not observed strictly, may cause death or serious injury. The “Caution” section contains matters which may result in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

●

The sign indicate the following meanings.

●

Please keep this manual after reading.

WARNING

PRECAUTIONS DURING INSTALLATION

●

Do not reconstruct the unit. Water leakage, fault, short circuit or fire may occur if you reconstruct the unit by yourself.

●

Please ask your sales agent or qualified technician for the installation of your unit. Water leakage, short circuit or fire may occur if you install the unit by yourself.

●

Please use earth line. Do not place the earth line near water or gas pipes, lightning-conductor, or the earth line of telephone. Improper installation of earth line may cause electric shock.

●

A circuit breaker should be installed depending on the mounting site of the unit. Without a circuit breaker, the danger of electric shock exists.

●

Do not install near location where there is flammable gas. The outdoor unit may catch fire if flammable gas leaks around it.

●

Please ensure smooth flow of water when installing the drain hose.

CAUTION

!

PRECAUTIONS DURING OPERATION

●

Avoid an extended period of direct air flow for your health.

W

A R N

I

N

G

!

●

Do not insert a finger, a rod or other objects into the air outlet or inlet. As the fan is rotating at a high speed, it will cause injury. Before cleaning, be sure to stop the operation and turn the breaker OFF.

●

During thunder storm, disconnect and turn off the circuit breaker.

●

Do not use any conductor as fuse wire, this could cause fatal accident.

!

Make sure to connect earth line.

Indicates the instructions that must be followed.

The sign in the figure indicates prohibition.

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

●

Should abnormal situation arises (like burning smell), please stop operating the unit and turn off the circuit breaker. Contact your agent. Fault, short circuit or fire may occur if you continue to operate the unit under abnormal situation.

●

Please contact your agent for maintenance. Improper self maintenance may cause electric shock and fire.

●

Please contact your agent if you need to remove and reinstall the unit. Electric shock or fire may occur if you remove and reinstall the unit yourself improperly.

●

If the supply cord is damaged, it must be replaced by the special cord obtainable at authorized service/parts centers.

W

A R N

I

N

G

!

(EN1) RAS-S18CPX (1-5) 3/4/08, 19:182

Black

– 3 –

ENGLISH

PRECAUTIONS DURING OPERATION

●

Do not attempt to operate the unit with wet hands, this could cause fatal accident.

●

When operating the unit with burning equipments, regularly ventilate the room to avoid oxygen insufficiency.

●

Do not direct the cool air coming out from the air-conditioner panel to face household heating apparatus as this may affect the working of apparatus such as the electric kettle, oven etc.

●

Do not use any aerosol or hair sprays near the indoor unit. This chemical can adhere on heat exchanger fin and blocked the evaporation water flow to drain pan. The water will drop on tangential fan and cause water splashing out from indoor unit.

●

Please ensure that outdoor mounting frame is always stable, firm and without defect. If not, the outdoor unit may collapse and cause danger.

●

Do not splash or direct water to the body of the unit when cleaning it as this may cause short circuit.

●

When operating the unit with the door and windows opened, (the room humidity is always above 80%) and with the air deflector facing down or moving automatically for a long period of time, water will condense on the air deflector and drips down occasionally. This will wet your furniture. Therefore, do not operate under such condition for a long time.

●

If the amount of heat in the room is above the cooling or heating capability of the unit (for example: more people entering the room, using heating equipments and etc.), the preset room temperature cannot be achieved.

●

This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely.

●

Young children should be supervised to ensure that they do not play with the appliance.

●

Do not climb on the outdoor unit or put objects on it.

●

Please switch off the unit and turn off the circuit breaker during cleaning, the high-speed fan inside the unit may cause danger.

●

Turn off the circuit breaker if the unit is not to be operated for a long period.

C A U T

I O N

!

●

The product shall be operated under the manufacturer specification and not for any other intended use.

●

Do not put water container (like vase) on the indoor unit to avoid water dripping into the unit. Dripping water will damage the insulator inside the unit and causes short-circuit.

●

Do not place plants directly under the air flow as it is bad for the plants.

(EN1) RAS-S18CPX (1-5) 3/4/08, 19:183

Black

– 4 –

INDOOR UNIT

NAMES AND FUNCTIONS OF EACH PART

Air filter

To prevent dust from coming into the indoor unit. (Refer page 17)

Front panel

Indoor unit indicators

Light indicator showing the operating condition. (Refer page 5)

Horizontal deflector

●

Vertical deflector

(Air Outlet)

(Refer page 12)

Remote controller

Send out operation signal to the indoor unit. So as to operate the whole unit. (Refer page 6)

OUTDOOR UNIT

Drain pipe

Condensed water drain to outside.

Connecting cord and insulation pipe for piping

Air inlet (Back and Left side)

Air outlet

WIDTH (mm)

1030

750

MODEL

RAS-S18CPX

RAC-S18CPX

HEIGHT (mm)

295

570

DEPTH (mm)

191

280

MODEL NAME AND DIMENSIONS

(EN1) RAS-S18CPX (1-5) 3/4/08, 19:184

Black

– 5 –

ENGLISH

INDOOR UNIT INDICATORS

OPERATION INDICATOR

● This figure shows the opening condition of

front panel. Refer to page 16 in relation to how to open or close the front panel.

OPERATION LAMP

This lamp lights during operation.

TIMER LAMP

This lamp lights when the timer is working.

FILTER LAMP

When the device is operated for a total of about 200 hours, the FILTER lamp lights to indicate that it is time to clean the filter. The lamp goes out when the “ (AUTO SWING)” button is pressed while the device is on “STANDBY MODE”.

TEMPORARY

SWITCH

TEMPORARY

SWITCH

HITACHI

TEMPORARY SWITCH

● Use this switch to start and stop when the remote controller does not work.

● By pressing the temporary switch, the operation is done in automatic mode.

(EN1) RAS-S18CPX (1-5) 3/4/08, 19:185

Black

– 6 –

NAMES AND FUNCTIONS OF REMOTE CONTROL UNIT

REMOTE CONTROLLER

This controls the operation of the indoor unit. The range of control is about 7 meters. If indoor lighting is controlled electronically, the range of control may be shorter. This unit can be fixed on a wall using the fixture provided. Before fixing it, make sure the indoor unit can be controlled from the remote controller.

●

Transmission sign

The transmission sign blinks when a signal is sent.

●

Display

This indicates the room temperature selected, timer status, function and intensity of circulation selected.

●

CIRCULATION button

Use this button to set air circulation in the room or start operation.

●

DEHUMIDIFYING button

Use this button to reduce humidity in the room or start operation.

●

COOLING button

Use this button to set cooling mode in the room or start operation.

●

RESET button

●

STOP button

Press this button to stop operation only.

●

SLEEP button

Use this button to set the sleep timer.

●

FAN SPEED selector

This determines the fan speed. Every time you press this button, the intensity of circulation will change from (AUTO) to (HI) to (MED) to (LOW).

●

AUTO SWING button

Controls the angle of the horizontal air deflector.

●

TEMPERATURE button

Use this button to raise or lower the temperature setting. (Keep pressed, and the value will change more quickly.)

●

OFF-TIMER button Select to turn OFF time.

●

ON-TIMER button Select to turn ON time.

Precautions for Use

●

Do not put the remote controller in the following places.

●

In direct sunlight.

●

In the vicinity of a heater.

●

Handle the remote controller carefully. Do not drop it on the floor, and protect it from water.

●

Once the outdoor unit stops, it will not restart for about 3 minutes (unless you turn the power switch off and on or unplug the power cord and plug it in again). This is to protect the device and does not indicate a failure.

CIRCULATION / START

DEHUMIDIFY / START

COOLING / START

FAN

FAN SPEED LOW MED HI

SLEEP TIMER

STOP

TIMER SELECTOR ON TIMER OFF TIMER

AUTO SWING

(EN2) RAS-S18CPX (6-12) 3/4/08, 19:196

Black

– 7 –

ENGLISH

COOLING OPERATION

Use the device for cooling when the outdoor temperature is 21-52°C. If indoor humidity is very high (over 80%), some dew may form on the air outlet grille of the indoor unit.

Press the button so that the display indicates

(COOL). Cooling operation starts with a beep. The cooling function does not start if the temperature setting is higher than the current room temperature (even though the (OPERATION) lamp lights). The cooling function will start as soon as you set the temperature below the current room temperature.

Set the desired FAN SPEED with the

(FAN SPEED) button

(the display indicates the setting).

(AUTO): The FAN SPEED is HI at first and varies to

MED or LOW automatically when the preset temperature has been reached.

(HI) : Economical as the room will become cool

quickly. (MED) : Fan speed slow.

(LOW) : Fan speed slower.

Set the desired room temperature with the TEMPERATURE button (the display indicates the setting).

The range of 25-28°C is recommended as the room temperature for cooling. If the temperature setting is 27°C, the room temperature will be controlled at around 27°C.

The temperature setting and the actual room temperature may vary somewhat depending on conditions.

Press the

(STOP) button to stop operation.

■ As the settings are stored in memory in the remote controller, you

only have to press the

(COOLING) button next time.

1

2

STOP

3

(EN2) RAS-S18CPX (6-12) 3/4/08, 19:197

Black

– 8 –

DEHUMIDIFYING OPERATION

Use the device for dehumidifying when the room temperature is over 16°C. When it is under 15°C, the dehumidifying function will not work.

■ Dehumidifying Function

When the room temperature is higher than the temperature setting: The device will dehumidify the room, reducing the room temperature to the preset level. When the room temperature is lower than the temperature setting: Dehumidifying will be performed at the temperature setting slightly lower than the current room temperature, regardless of the temperature setting. The function will stop (the indoor unit will stop emitting air) as soon as the room temperature becomes lower than the setting temperature.

■ As the settings are stored in memory in the remote controller, you

only have to press the

(DEHUMIDIFY) button next time.

Set the desired room temperature with the TEMPERATURE button (the display indicates the setting).

The range of 20-26˚C is recommended as the room temperature for dehumidifying.

2

Press the button so that the display indicates

(DEHUMIDIFY). Dehumidifying operation starts with a beep. The FAN SPEED is set at LOW automatically. The FAN SPEED button does not work.

1

Press the (STOP) button to stop operation.

STOP

(EN2) RAS-S18CPX (6-12) 3/4/08, 19:198

Black

– 9 –

ENGLISH

CIRCULATION OPERATION

Press the button so that the display indicates (CIRCULATION). Circulating operation starts with a beep.

Press the FAN SPEED button and select the desired FAN SPEED (the display indicates your choice).

Press the temperature control button to set to the desired temperature.

■ As the settings are stored in memory in the remote controller,

you only have to press the

(CIRCULATION) button next time.

2

1

3

Press the (STOP) button to stop operation.

STOP

■ Circulation Function

● During circulation operation, compressor will not be running and there is no cooling operation with only

indoor fan running.

● When the setting temperature is higher than room temperature, indoor fan will stop running.

(EN2) RAS-S18CPX (6-12) 3/4/08, 19:199

Black

– 10 –

HOW TO SET THE SLEEP TIMER

Press the (SLEEP) button, and the display changes as shown below.

Mode

Sleep timer

Indication

1 hour 2 hours 3 hours 7 hours

Sleep timer off

44 44

1

Sleep Timer: The device will continue working for the designated number of hours and then turn off. Point the signal window of the remote controller toward the indoor unit, and press the SLEEP button. The timer information will be displayed on the remote controller. The TIMER lamp lights with a beep from the indoor unit. When the sleep timer has been set, the display indicates the turn-off time.

Cooling

“ ”

and

dehumidifying

“ ”

Explanation of the sleep timer

The device will control the FAN SPEED and room temperature automatically so as to be quiet and good for people’s health. You can set the sleep timer to turn off after 1, 2, 3 or 7 hours. The FAN SPEED and room temperature will be controlled as shown below.

Function Operation

The room temperature will be controlled 2°C above the temperature and the FAN SPEED will be set to LOW setting 60 minutes after the setting of the sleep timer.

Operation with the sleep timer

SLEEP

(EN2) RAS-S18CPX (6-12) 3/4/08, 19:1910

Black

– 11 –

ENGLISH

HOW TO SET THE TIMER

■ ON Timer and OFF Timer are available.

OFF TIME setting

● Select the OFF TIME by pressing the (OFF) Button.

● Setting time will change according to the below sequence

when you press the button.

OFF Timer Reservation

■ Operation stop at setting time

1 2 3 9 10 11 12

1 hour interval

(CANCEL OFF TIMER)

ON TIME setting

● Select the ON TIMER by pressing the (ON)

Button.

● Setting time will change according to the below

sequence.

ON Timer Reservation

1 2 3 9 10 11 12

1 hour interval

(CANCEL ON TIMER)

■ Operation will start for setting temperature at setting time (The starting time may different depend on the room temperature and set temperature).

(EN2) RAS-S18CPX (6-12) 3/4/08, 19:1911

Black

– 12 –

Adjustment of the conditioned air in the upward and downward directions. According to “Dehumidifying” or “Cooling” operation, the horizontal air deflector is automatically set to the proper angle suitable for each operation. The deflector can be swing up and down and also set to the desired angle using the “ (AUTO SWING)” button. (If the angle of the deflector is changed, it will not return to the autoset position after operations start unless the operation mode is switched.)

ADJUSTING THE AIR DEFLECTORS

1

2

Adjustment of the conditioned air to the left and right.

Hold the vertical air deflector as shown in the figure and adjust the conditioned air to the left and right.

● If the “ (AUTO SWING)” button is pressed once,

the horizontal air deflector swings up and down. If the button is pressed again, the deflector stops in its current position. Several seconds (about 6 seconds) may be required before the deflector starts to move.

● In “Cooling” operation, do not keep the horizontal air

deflector swinging for a long time. Some dew may form on the horizontal air deflector and dew may drop.

(EN2) RAS-S18CPX (6-12) 3/4/08, 19:1912

Black

– 13 –

ENGLISH

HOW TO EXCHANGE THE BATTERIES IN THE REMOTE CONTROLLER

1

Remove the cover as shown in the figure and take out the old batteries.

=

2

Install the new batteries. The direction of the batteries should match the marks in the case.

1. Do not use new and old batteries, or different kinds of batteries together.

2. Take out the batteries when you do not use the remote controller for 2 or 3 months.

3. Use high quality and high performance AAA batteries to avoid short operating life and electrolyte leakages

CAUTION

!

When using the remote control, if there is no response from the air conditioner unit and or the remote control has fading and dim displays, the batteries in the remote control device need to be removed and replaced with new ones

(EN3) RAS-S18CPX (13-22) 3/4/08, 19:2013

Black

– 14 –

Suitable Room Temperature Install curtain or blinds

Ventilation Effective Usage Of Timer

Do Not Forget To Clean The Air Filter

Please Adjust Suitable Temperature

For Baby And Children

Warning

Freezing temperature is bad for health and a waste of electric power.

!

It is possible to reduce heat entering the room through windows.

At night, please use the “OFF or ON timer operation mode”, together with your wake up time in the morning. This will enable you to enjoy a comfortable room temperature. Please use the timer effectively.

Dusty air filter will reduce the air volume and the cooling efficiency. To prevent from wasting electric energy, please clean the filter every 2 weeks.

Please pay attention to the room temperature and air flow direction when operating the unit for baby, children and old folks who have difficulty in movement.

Caution

Do not close the room for a long period of time. Occasionally open the door and windows to allow the entrance of fresh air.

!

THE IDEAL WAYS OF OPERATION

(EN3) RAS-S18CPX (13-22) 3/4/08, 19:2014

Black

– 15 –

ENGLISH

FOR USER’S INFORMATION

The Air Conditioner And The Heat Source In The Room

Not Operating For A Long Time

When Lightning Occurs

Caution

If the amount of heat in the room is above the cooling capability of the air conditioner (for example: more people entering the room, using heating equipments and etc.), the preset room temperature cannot be achieved.

!

When the indoor unit is not to be used for a long period of time, please switch off the power from the mains. If the power from mains remains “ON”, the indoor unit still consumes about 8W in the operation control circuit even if it is in “OFF” mode.

Warning

To protect the whole unit during lightning, please stop operating the unit and remove the plug from the socket.

!

OFF

Interference From Electrical Products

Inverter-type fluorescent lamp.

To prevent interference, place at least 1m away.

TV

Caution

To avoid noise interference, please place the indoor unit and its remote controller at least 1m away from electrical products.

!

(EN3) RAS-S18CPX (13-22) 3/4/08, 19:2015

Black

– 16 –

ATTACHING THE AIR CLEANSING FILTERS

1

Open the front panel.

● Pull up the front panel by holding it at both sides

with both hands.

2

Remove the filter.

● Push upward to release the claws and pull out the

filter.

3

4

Attach the filters.

● Attach the filters by ensuring that the surface written

“FRONT” is facing front.

● After attaching the filters, push the front panel at

three arrow portion as shown in figure and close it.

Cleaning and maintenance must be carried out only by qualified service personal. Before cleaning, stop operation and switch off the power supply.

CAUTION

!

CAUTION

NOTE

Claws

(4 places)

Attaching the air cleansing filters to the filter.

● Attach the air cleansing filters to the frame by gently

compress its both sides and release after insertion into filter frame.

Do not bend the air cleansing filter as it may cause damage to the structure.

● In case of removing the air cleansing filters, please follow the above procedures.

● The cooling capacity is slightly weakened and the cooling speed becomes slower when the air

cleansing filters are used. So, set the fan speed to "HIGH" when using it in this condition.

● Air cleansing filters are washable and can be use in 1 year time. Type number for this air cleansing

filter is <SPX-CFH18>. Please use this number for ordering when you want to renew it.

● Do not operate the air conditioner without filter. Dust may enter the air conditioner and fault may occur.

(EN3) RAS-S18CPX (13-22) 3/4/08, 19:2016

Black

– 17 –

ENGLISH

MAINTENANCE

Cleaning and maintenance must be carried out only by qualified service personal. Before cleaning, stop operation and switch off the power supply.

1. AIR FILTER

Clean the air filter, as it removes dust inside the room. In case the air filter is full of dust, the air flow will decrease and the cooling capacity will be reduced. Further, noise may occur. Be sure to clean the filter following the procedure below.

!

CAUTION

1

Open the front panel and remove the filter

● Gently lift and remove the air cleansing filter

from the air filter frame.

2

3

● Re-insert the air cleansing filter to the filter

frame. Set the filter with “FRONT” mark facing front, and slot them into the original state.

● After attaching the filters, push the front panel

at three arrow portions as shown in figure and close it.

!

CAUTION

● Do not wash with hot water at more than 40°C. The filter may shrink.

● When washing it, shake off moisture completely and dry it in the shade; do not expose it directly to

the sun. The filter may shrink.

● Do not use detergent on the air cleansing filter as some detergent may deteriorate the filter electrostatic

performance.

PROCEDURE

Vacuum dust from the air filter and air cleansing filter using vacuum cleaner. If there is too much dust, rinse under running tap water and gently brush it with soft bristle brush. Allow filters to dry in shade.

NOTE:

● Air cleansing filter should be cleaned every month or sooner if noticeable loading occurs. When

used overtime, it may loose its deodorizing function. For maximum performance, it is recommended to replace it every 1 year depending on application requirements.

(EN3) RAS-S18CPX (13-22) 3/4/08, 19:2017

Black

– 18 –

2. Washable Front Panel

● Remove the front panel and wash with clean

water. Wash it with a soft sponge. After using neutral detergent, wash thoroughly with clean water.

● When front panel is not removed, wipe it with

a soft dry cloth. Wipe the remote controller thoroughly with a soft dry cloth.

● Wipe the water thoroughly.

If water remains at indicators or signal receiver of indoor unit, it causes trouble.

Method of removing the front panel. Be sure to hold the front panel with both hands to detach and attach it.

!

CAUTION

● Do not splash or direct water to the body of the unit when cleaning

it as this may cause short circuit.

● Never use hot water (above 40°C), benzine, gasoline, acid, thinner or

a brush, because they will damage the plastic surface and the coating.

Removing the Front Panel

Arm

● When the front panel is fully opened with

both hands, push the right arm to the inside to release it, and while closing the front panel slightly, put it out forward.

Attaching the Front Panel

● Move the projections of the left and right

arms into the Flanges in the unit and securely insert them into the holes.

Projection

Hole

Flange

3. MAINTENANCE AT BEGINNING OF LONG OFF PERIOD

● Run the unit by setting the operation mode to

(CIRCULATION), the temperature to 16°C and the fan speed to HI for about half a day on a fine day, and dry the whole of the unit.

● Switch off the power plug.

Air

Blow

(EN3) RAS-S18CPX (13-22) 3/4/08, 19:2018

Black

– 19 –

ENGLISH

1

2

3

REGULAR INSPECTION

PLEASE CHECK THE FOLLOWING POINTS BY QUALIFIED SERVICE PERSONAL EITHER EVERY HALF YEARLY OR YEARLY. CONTACT YOUR SALES AGENT OR SERVICE SHOP.

Is the earth line disconnected or broken?

Is the mounting frame seriously affected by rust and is the outdoor unit tilted or unstable?

Is the plug of power line firmly plugged into the socket? (Please ensure no loose contact between them).

Confirm

Cleaning and maintenance must be carried out only by qualified service personal. Before cleaning, stop operation and switch off the power supply.

!

CAUTION

● Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the earth line of telephone. Improper installation of earth line may cause electric shock.

!

● A circuit breaker should be installed depending on the mounting site of the unit. Without a circuit

breaker, the danger of electric shock exists.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow : Earth Blue : Neutral

Brown : Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

NOTE

If the supply cord is damaged, it must be replaced by the special cord obtainable at authorized service/ parts centers.

(EN3) RAS-S18CPX (13-22) 3/4/08, 19:2019

Black

– 20 –

AFTER SALE SERVICE AND WARRANTY

WHEN ASKING FOR SERVICE, CHECK THE FOLLOWING POINTS.

When it does not operate

● Is the fuse all right?

● Is the voltage extremely high or low?

● Is the circuit breaker “ON”?

● Was the air filter cleaned?

● Does sunlight fall directly on the outdoor unit?

● Is the air flow of the outdoor unit obstructed?

● Are the doors or windows opened, or is there any source of

heat in the room?

● Is the set temperature suitable?

CONDITION CHECK THE FOLLOWING POINTS

Notes

● In quiet or stop operation, the following phenomena may occassionally

occur, but they are not abnormal for the operation. (1) Slight flowing noise of refrigerant in the refrigerating cycle. (2) Slight rubbing noise from the fan casing which is cooled and then

gradually warmed as operation stops.

● The odor will possibly be emitted from the room air conditioner because

the various odor, emitted by smoke, foodstuffs, cosmetics and so on, sticks to it. So the air filter and the evaporator regularly must be cleaned to reduce the odor.

●

Please contact your sales agent immediately if the air conditioner still fails to operate normally after the above inspections. Inform your agent of the model of your unit, production number, date of installation. Please also inform him regarding the fault.

●

Power supply shall be connected at the rated voltage, otherwise the unit will be broken or could not reach the specified capacity.

When it does not cool well When it does not hot well

Please note: On switching on the equipment, particularly when the room light is dimmed, a slight brightness fluctuation may occur. This is of no consequence. The conditions of the local Power Supply Companies are to be observed.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.

NOTE:

(EN3) RAS-S18CPX (13-22) 3/4/08, 19:2020

Black

– 21 –

ENGLISH

MEMO

.....................................................................................................................................................................................

This product conforms with the protection requirements of council directives 89/336/EEC relating to electromagnetic compatibility and 73/23/EEC relating to electrical equipment designed for use within certain voltage limits.

Minimum Maximum

Indoor Dry bulb °C21 32

Wet bulb °C15 23

Outdoor Dry bulb °C21 52

Wet bulb °C15 31

Note

● Avoid to use the room air conditioner for cooling operation when the outside temperature is below

21°C (70°F). The recommended maximum and minimum operating temperatures of the hot and cold sides should be as below:

(EN3) RAS-S18CPX (13-22) 3/4/08, 19:2021

Black

– 22 –

MEMO

.....................................................................................................................................................................................

(EN3) RAS-S18CPX (13-22) 3/4/08, 19:2022

Black