Instruction
Manual
Hitachi Air Purifi er
with Humidifying Function
Model
EP-A7000
Contents
Before Use
Features / Name of Each Component / Operation
Buttons and Indicators / Accessories
Safety Precautions · · · · · · · · · · · · · · · · · · ·
Cautions on Use · · · · · · · · · · · · · · · · · · · · ·
Preparations for Operation · · · · · · · · · · · · ·
·
Setting Filter in Purifi er · · · · · · · · · · · · · · · · · ·
·
Inserting Batteries into Remote Controller
· Filling Water Tank · · · · · · · · · · · · · · · · · · · · ·
Installation · · · · · · · · · · · · · · · · · · · · · · · · · ·
Operating Air Purifi er
Using Remote Controller · · · · · · · · · · · · · ·
· Starting Operation · · · · · · · · · · · · · · · · · · · ·
· Selecting Operation Mode · · · · · · · · · · · · · · ·
· Switching Airfl ow Rate · · · · · · · · · · · · · · · · ·
·
Max Operation · · · · · · · · · · · · · · · · · · · · · ·
Using Timer · · · · · · · · · · · · · · · · · · · · · · · ·
·
Using the Control on Purifi er · · · · · · · · · · ·
Memory Function / Sensors / Auto Detection
· Memory Function · · · · · · · · · · · · · · · · · · · ·
·
Air Sensor · · · · · · · · · · · · · · · · · · · · · · · · ·
Odor Sensor · · · · · · · · · · · · · · · · · · · · · · · ·
·
· Dust sensor · Humidity Sensor · · · · · · · · · · ·
·
Auto Detection · · · · · · · · · · · · · · · · · · · · · ·
· Adjusting Sensor Sensitivity Setting · · · · · · · · ·
Useful Feature · · · · · · · · · · · · · · · · · · · · · ·
Eco Operation · · · · · · · · · · · · · · · · · · · · · · ·
·
Dimmer Control · · · · · · · · · · · · · · · · · · · · · ·
·
· · · · · · · · ·
· · · · · · ·
· · · · · ·
E-2
E-4
E-7
E-8
E-8
E-9
E-9
E-10
E-10
E-10
E-11
E-12
E-13
E-13
E-14
E-14
E-14
E-14
E-14
E-15
E-15
E-16
E-17
E-17
E-17
Thank you for purchasing a Hitachi air
purifi er.
This air purifi er is for home use only. Do
not use it for any other purpose than air
purifying.
Please read this instruction manual
carefully before use to ensure proper
operation of the unit.
Keep this manual for future reference in
an easily accessible place.
Read the “Safety Precautions” P.E-4,E-6
to ensure proper use.
Cleaning and Maintenance
Cleaning · · · · · · · · · · · · · · · · · · · · · · · · · ·
When the “Clean Humidifying Filter” Indicator Comes On
·
· Water Tank · Humidifying Filter · · · · · · · · · · ·
Replacing Humidifying Filter · · · · · · · · · · · · ·
·
·
Water Tray / Tray Cover · · · · · · · · · · · · · · · · ·
Pre-fi lter · · · · · · · · · · · · · · · · · · · · · · · · · ·
·
·
Purifi er Body · Dust sensor · · · · · · · · · · · · ·
Filter Replacement · · · · · · · · · · · · · · · · · ·
Replacement Interval
·
·
Replacing the Filter · · · · · · · · · · · · · · · · · · ·
Alert Display · · · · · · · · · · · · · · · · · · · · · · ·
Troubleshooting Guide · · · · · · · · · · · · · · ·
Replacement Parts · · · · · · · · · · · · · · · · · ·
Specifi cations · · · · · · · · · · · · · · · · · · · · · ·
· Precautions on Filter Handling
· · · · · ·
· · · · · ·
E-18
E-18
E-19
E-20
E-20
E-21
E-22
E-23
E-23
E-24
E-25
E-25
E-28
E-28
Features / Name of Each Component /
Accessories
Dust sensor P.E-15
Dust sensor is capable of sensing
the dusts in the air such as cigarette
smoke, house dust, pollen, etc.
Deodorizing filter
(Nano power deodorizing filter)
Set this filter to the back
side of the unit.
Humidity sensor P.E-15
Senses humidity.
Filter assembly
(Allergen-free, HEPA filter)
Set this filter to the front side of the
unit.
Pre-filter
Removes large size dust.
Indicator section
P.E-3
Panel
Odor sensor
Senses odor in the air.
P.E-14
Shutter
(air inlet)
Remote controller
Humidifying filter
Purifier
Remote controller pocket
Handle
Water
tank
手前
Tray cover
Water tray
Air outlet
Hand grip
E-2
Filter
Housed inside
the purifi er.
* Be sure to remove
this fi lter from plastic
bag before operating
the purifi er.
Air inlet (around the panel)
No air inlet on the
panel front face.
dust fi lter(x1)
deodorizing fi lter(x1)
Power plug
Power
cord
Provided Accessories
Pre-fi lter
(x1) (x1) (x2) (x1)
Remote controller
“AAA” R03
batteries for
remote controller
Humidifying filter
手前
P.E-OO shows a page with further description.
Operation Buttons and Indicators
Humidity Level
Indicates approx. humidity level in the
room during operation.
Low Moderate High
Orange Orange Orange OrangeGreen
P.E-10, 15
Airflow Level P.E-12
Indicates airflow rate during operation. (Indicator: Green)
Auto
: Airflow rate during auto operation
: Indicates eco operation is active.
When airflow rate is switched using the
airflow button on the remote controller, the
selected airflow rate is indicated.
: Silent
: Med
: Strong or Max (blinking)
Operation Mode P.E-11
Shows the operation mode.
Air Purify, Pollen, Strong
Deodorization
Indicator: Green
Humidify, Skin Moisturize
Indicator: Orange
Clean Humidifying
Filter
Shows the time to
clean the humidifying
filter. (Indicator: Red)
P.E-18
On/Off Button
Use this button to start or stop operation and to switch the operation mode.
Air Sensor
Level of air contamination detected by the
dust sensor and odor sensor is shown by
how the indicator is lit. (Indicator: Green)
P.E-14
P.E-14
Features / Name of Each Component / Operation Buttons and Indicators / Accessories
Infrared Remote Receiver
Receives remote control
signal.
Timer
The indicator is lit when
4-hour timer is set.
(Indicator: Green)
P.E-13
Remote Controller
Point the remote controller at the infrared receiver on the purifier when you operate.
The remote controllable distance is approx. 6m maximum when pointing the remote
controller squarely to the receiver.
On/Off Button P.E-10
Press this button to start or
stop operation.
eco Button
Press this button to start or
stop eco operation.
Max button P.E-13
Press this button to start
max operation.
Note
P.E-17
The remote control may not work in a room where inverter lighting apparatus or electronic quick
start lighting apparatus is used, or when the infrared receiver is exposed to direct sunlight.
If you operate the remote controller not pointing straight to the front face of the purifier, the sensitivity
will be reduced. Operate the controller from the place in front of the purifier whenever possible.
Airflow Button P.E-12
Press this button to switch
airflow rate.
Mode Button P.E-11
Press this button to switch
operation mode.
Timer Button P.E-13
Press this button to set
Off-timer.
Sensor Setting Button
Press this button to switch
sensor sensitivity.
P.E-16
E-3
Safety Precautions
Please read the following safety precautions carefully before using the air purifier.
To prevent injury to the user or other people and property damage, the following instructions must
be followed. Also read the precautions appearing in the text carefully to ensure proper use.
Definition of each indication
Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classifi ed by the following indications.
This symbol indicates the
WARNING
CAUTION
possibility of death or serious
injury.
This symbol indicates the
possibility of injury or damage
to property.
Meanings of Symbols
Indicates “warning or caution”.
Indicates “prohibition”.
Indicates a “must”.
WARNING
To Prevent Fire, Electric Shock and Injury
AC Outlet, Power Plug and Power Cord
Before cleaning and other maintenance, be
sure to unplug the power cord from AC outlet,
and never pull it out or insert it with wet hands.
Otherwise, it may cause electric shock or injury.
Be sure to hold the plug, not the power
cord, when unplugging it from AC outlet.
It may cause electric shock or short-circuit, resulting in a fi re.
Be sure to unplug the power cord from AC outlet when
leaving air purifi er unused for an extended period of
time. Also drain the water tank and water tray.
Otherwise, it may cause electric shock, fi re or unpleasant odor.
Securely insert the power plug into AC outlet.
Otherwise, it may cause electric shock, fi re, smoke
emission and ignition.
Remove dust of the power plug periodically using a dry cloth.
Otherwise, it may cause a fi re.
When you notice anything abnormal (water leakage, burnt
odor, etc.) stop the operation and unplug the power cord.
It may cause electric shock or fi re due to ground
leak or short-circuit.
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualifi ed persons in order to avoid a hazard.
Do not use with a voltage other than 220-240V AC.
Otherwise, it may cause a fi re or electric shock.
Do not damage the power cord.
(Do not break, modify, forcibly bend, pull
or twist it. Also do not place any heavy
object on it or pinch it.)
Otherwise, it may cause a fi re or electric shock.
Do not use damaged power cord or power
plug, or loose socket.
Otherwise, it may cause electric shock,
short-circuit or ignition.
Clean
220-240V
Panel
Purifier
Power cord
Power plug
E-4
WARNING
Water Tank, Water Tray and Humidifying Filter
Do not operate the unit without setting any of the water tank, water tray and
humidifying fi lter in place.
Otherwise, it may cause injury or unit failure.
Do not use any detergent (neither kitchen nor laundry use) when cleaning the
water tank or water tray.
Ingredients of detergent may cause damage and subsequent water leakage, or
electric shock, injury or unit failure.
Do not carry the water tank by holding its handle.
Dropping the tank may cause inadvertent injury or other accident.
Do not disassemble the tank cap.
Otherwise, it may cause inadvertent accident such as small children swallowing it
by mistake.
Place of Use
Do not use in a humid place such as in bathroom.
It may cause electric shock or unit failure.
Do not place air purifi er near a hot object such as a heater.
It may cause unit failure or deformation.
Do not use in a place where soot of oil, such as machine oil, is fl oating in the air.
It may cause a crack or fi re.
Do not use air purifi er in a kitchen as a substitute of ventilating fan.
It may cause a unit failure.
Do not use in a place where any organic solvent or chemicals are used.
It may cause a discoloration, deformation or fi re.
Do not use the air purifi er in a place where a machine tool such as a grinder
and welder that produces sparks such as fl ammable dust is installed.
Sparks may cause fi re.
Handle
Water tank
Safety Precautions
Tank cap
Purifier Body and Panel
Do not use benzene or thinner when wiping or spray fl ammable gas such as
insecticides.
It may cause a crack, electric shock, catching of fi re and explosion.
Do not let air purifi er intake infl ammables, lit cigarettes or incense.
It may cause a fi re.
Securely hold the grip when carrying air purifi er.
Dropping it may cause injury or damage to it.
Miscellaneous
In case the unit becomes inoperative or anything abnormal such as smoke or
unusual odor is noticed, immediately unplug the power cord to prevent possible
accident and contact your dealer for check and repair.
It may cause electric shock or fi re due to ground leak or short-circuit.
Ventilate a room frequently if any heating appliance is simultaneously used with air purifi er.
Otherwise, it may cause carbon monoxide poisoning.
The appliance is not to be used by children or persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction.
Children should be supervised to ensure that they do not play with the appliance.
Never attempt to disassemble, modify or repair by yourself.
It may cause a fi re, electric shock or injury. (Contact your dealer for repair.)
Do not put your fi nger or any other object into air outlet and inlet.
It may cause injury or unit failure.
Do not submerge or splash water on the unit. Also avoid fi lling water directly into the unit.
It may cause electric shock or short-circuit.
Do not tilt or tip over the unit. Do not put your weight on the unit or step on it.
It may cause tipping over of the unit and injury or water leakage.
Do not install in unstable place or anywhere near infant child.
It may cause tipping over of the unit and injury.
Flammable
gas
E-5
Safety Precautions (Continued)
CAUTION
Miscellaneous
Securely hold the grip when carrying
air purifi er.
Damaging or dropping it may cause injury.
When you attach or detach the panel
and water tank, do it slowly and securely.
Otherwise, it may cause water leakage or
injury of fi ngers pinched.
Use dry cell batteries properly after
reading the precautions on them.
Renew water in the water tank daily using
tap water and clean the tank periodically
according to the instructions given in the
“Cleaning” section of this manual.
Continued use without cleaning may allow
propagation of molds or bacteria due to
dirt and water scale, producing unpleasant
odor. In rare cases, they may cause a
health risk to those who are hyperactive. In
such a case, please seek medical advice.
Only use fresh tap water
Otherwise, it may cause deformation or
degeneration of parts, unit failure or unpleasant
smell due to propagation of molds or bacteria.
Do not use hot water (over 40ºC), water
through water purifi er, alkali ion water, mineral
water, well water or the like. Do not put organic
solvent or chemicals into the water tank.
Do not drink, or let drink, water in the
water tank and water tray.
It may cause a health threat.
Do not leave the detached water tank
with its cap closed.
Inner pressure of the tank changes
according to ambient temperature change
and may cause water leakage or injury
due to deformation or damage.
Use a genuine fi lter for the Hitachi Air Purifi er.
Other fi lters may cause unit failure.
Do not operate the unit when
using fumigating (smoking) type
insecticide.
Using such insecticide will cause
chemicals to accumulate in the unit and
to be emitted by subsequent operation,
which can be harmful to heath.
After using insecticide, ventilate the
room well before running the purifi er.
Do not allow water to freeze.
Water tank may be damaged, causing
a risk of electric shock and unit
failure. Whenever freezing of water is
anticipated, drain the water tank and
water tray.
Do not use the purifi er having water
leakage trouble.
It may cause electric shock. When
water leaks, unplug the power cord
from AC outlet and ask for repair.
Do not carry the purifi er with its
water tank fi lled.
It may cause water leakage or injury.
If you carry the purifi er with fi lled water
tank, level of water in the tray will rise
and cause the water to overfl ow when
operated.
Drain the water tank and water tray
fi rst, and set them on the unit before
carrying.
Do not tip over or drop the water
tank when it is fi lled.
It may cause injury or result in deformed
or damaged tank. Hold the tank
securely when you fi ll it with water.
Do not look into the indicator.
It may cause injury to your eyes.
To Prevent Floor Scratches or Wall Stains
During Cleaning / Place of Use
During cleaning, lay a soft cloth on
the fl oor and place the purifi er and
detached components (panel, water
tank, water tray, etc.) on it.
Otherwise, it may cause scratches on
the fl oor.
When you pull out the water tray, be
careful not to scratch the fl oor with
bottom of the tray.
E-6
Do not use the air purifi er near the
wall that cannot be scrubbed such
as cloth-covered white wall.
The air purifi er will take in the
surrounding air and may produce local
stains.
Cautions on Use
Do not install in an unstable or sloped
place, or near any obstacles.
The unit may fall or drop,
resulting in damage or unit failure.
If the space between the unit and
floor remains humid, the floor
may get moldy.
Using the unit tilted may cause
water leakage.
Do not drag the unit on any floor susceptible
to scratches or on thick carpet.
It may cause damage on floor or carpet surface.
Do not run with filter detached.
No cleaning effect is
obtainable without filter.
Running without filter
may also cause unit
failure.
Do not directly fan animals and plants.
Air drafts may adversely affect them.
Do not place anything on the air purifier
body, and do not block the
air inlet or air outlet.
Acts of the sort may cause unit
failure.
Do not touch or move the unit (angle
or lift the unit) during operation.
Moving the operating unit may cause the fan to contact
the inner case, resulting in noise and possibly unit failure.
Do not place the purifier in a place exposed
to direct sunlight.
Safety Precautions Cautions on Use
Direct sunlight may
cause deformation,
discoloration or
malfunction.
Do not block or touch the infrared receiver,
odor sensor, Dust sensor or humidity sensor.
Infrared receiver may be stained
or damaged to reduce its
sensitivity.
Sensors may be degraded in
their sensitivity.
Do not install in a place where the air from the
purifier will blow directly on furniture, electric
appliance, wall or ceiling.
Humid air may cause stain
or deformation of furniture,
or may cause unit failure.
Ventilate closed room occasionally.
The air purifier does not have a ventilation
effect.
✽
The air purifier cannot
remove hazardous
substance in cigarettes
(carbon monoxide, etc.).
Do not subject remote controller to
impact.
Do not drop the remote
controller or step on it, and
do not place any object on
it. Doing so may cause unit
failure.
Do not subject water tank to impact.
Water may leak from the tank
to wet the floor. Also water
may drip from the tank cap to
wet the floor.
Do not use near television or radio.
Broadcast may be
interfered. Install the air
purifier 2m or more away
from such devices.
E-7
Preparations for Operation
Lay a soft cloth or the like beneath the purifier to protect the floor against scratch.
CAUTION
No cleaning effect is obtainable if the filter is installed with plastic bag. It may also be a cause of malfunction.
Do not tip over or tilt the purifier.
Setting Filter in Purifier
Remove the panel.
Place the unit on a level, stable surface.
Hold the panel at both sides, pull it
gently forward and then slightly upward,
and remove it.
Remove the pre-filter.
Remove the filter.
(There are dust filter and deodorizing filter.)
Remove the filter packed in a plastic bag from inside the unit.
Take the filter out of a plastic bag.
Remove the packing.
Install the Deodorizing filter.
Install the deodorizing filter so that its black surface
faces the front (white surface in the back).
(Perform the same procedure when replacing filter.)
Disengage the tabs of the
pre-filter (4 locations).
Be sure to remove the packing.
The back
(White)
front side(Black)
Insert the filter all the way until the label
(deodorizing filter position indicator) is hidden.
Be sure to take out the filter from a plastic bag.
Note
Do not block the filter front face with cloth or paper.
Same precautions should be taken for the dust
filter as well.
Install the dust filter
on the unit.
Insert the filter all the
way until the label (dust
filter position indicator) is
hidden.
Install the pre-filter on the unit.
Reinstall the panel on the unit.
Insert the two tabs on top of the
panel into the two holes on the unit.
Dust filter
Deodorizing filter
(Black surface)
White
surface
Pre-filter tabs
E-8
Gently push bottom of the panel until
it clicks to close it securely.
Insert into the hole.
Inserting Batteries into Remote Controller
ᚻ೨
Remove the battery
compartment cover.
Cover
(for Humidify Mode and Skin Moisturize Modes)
Filling Water Tank
Gently remove the water tank.
While pressing the upper part of the
water tank handle, lift it obliquely
upward, and remove the water tank by
supporting it in the bottom.
Handle
Insert batteries and close the cover.
Insert the provided two “AAA” R03 batteries
with the correct polarities as instructed.
Since the batteries are provided when shipped from
the factory, their lives may be shorter than brand-new
ones because of self-discharge.
Batteries are consumable
When replacing batteries, replace the two batteries simultaneously.
Only use two manganese batteries or two alkali batteries.
Do not mix them.
Remove the tank cap and fill fresh tap
water of normal temperature.
Rubber packing
Check that the tank cap is equipped
with a rubber packing.
Loosen
Tighten
Do not push in the
pin in the cap center.
Doing so may cause
water leakage.
Preparations for Operation
Hold the water tray.
Do not carry the water tank by holding its
handle. Instead, hold the tank with both
CAUTION
hands and carry it while keeping the tank
cap side up. When the water tank is wet,
wipe off water drops before carrying.
Pull out the water tray, check
that the humidifying filter and
tray cover are equipped, and
then retract the tray.
The humidifying filter absorbs water supplied
from the water tank for humidifying operation.
Humidifying filter
Water tray
Handle
Press the center pin of the tank cap, and check that it
comes back by spring.
Tighten the tank cap firmly, wipe off spilt water, and
check that there is no water leakage.
Wipe off water on the water tank handle if any.
The tank cap is a consumable part. P.E-28
(If it leaks water due to deteriorated rubber packing,
please purchase separately available part for
replacement.)
Set the water tank into the water tank
holder.
Be sure to handle the water-filled tank with both hands.
Press in the tank securely until it clicks. Inadequate
setting may cause the water tank to fall or result in water
leakage.
Pin
Tray cover
Water tray
Slowly pull out the water tray while lifting it
obliquely upward.
Do not set the water tank without having the water tray in place. Otherwise, the water tank may tip over.
When you pull out the water tray, be careful not to scratch the floor with bottom of the tray.
CAUTION
Note
Do not leave the detached water tank with its cap closed.
Inner pressure of the tank changes according to ambient temperature change and may cause water
leakage or injury due to deformation or damage.
Humidifying function works automatically when the water tank and water tray are filled with water.
If you do not need humidification, operate the unit without filling water in the water tank and water tray.
CAUTION
When you remove the water tank, water may
drip from the tank cap. Lay a dry cloth before
removing the water tank.
E-9
Installation
Install the purifier on a level, stable and sturdy surface.
Avoid any place close to cooling or heating appliance, and select a well-ventilated place.
Keep the purifier at least 90 cm away from the walls in both sides. Otherwise, discharged air will mix with
surrounding air and the walls may become dirty.
Do not place the purifier on unstable floor or pedestal.
WARNING
Falling or dropping of the purifier may cause damage, failure or water leakage.
Using the purifier in an inclined position may cause water leakage.
Using Remote Controller
Here we describe how to operate the air purifier using the remote controller. For the operation using
the control on the purifier, please refer to page E-14.
Starting Operation
Remote Controller Air Purifier Indicator Section
Securely insert the power plug
into AC outlet.
Press
button.
Operation starts and the indicators are lit.
Pressing
button during
operation will stop the operation.
In the first 3 minutes after the power cord is plugged
in, the unit will check room air condition and save
it in memory. During the time, the “Air Sensor”
indicator and “Humidity
You may start the operation in less than 3 minutes
after plugging. In this case too, the “Air Sensor” and
“Humidity Level 50” indicators will continue to blink.
After 3 minutes, the indicators will stop to blink and
show the level of air contamination and humidity.
Blink
The “Air Purify” mode indicator is lit in green. *
Lit in green
Note
If On/Off button is not pressed after plugging the power
cord, all indicators will go off after the “Air Sensor” and
“Humidity Level 50” indicators blink for 3 minutes.
(Remote controller operation is accepted even in
this state.)
Level 50” indicator will blink.
Blink
E-10
*
The factory setting is “Air Purify”.
From the second time onward, the memory function enables the operation with memorized conditions.
Stand-by Power Consumption
So long as the power plug is left inserted in AC outlet, approx. 4W power will be consumed even if the
unit is not used. (Unplug the power cord when the unit is left unused for an extended period of time.)
Selecting Operation Mode (Basics)
P.E-14
5 operation modes are available for your choice.
In every operation mode, the fan will not stop during operation.
(In the eco operation mode, the fan may stop.
In every operation mode, air purifying function will work.
Upon every switching of operation mode, airflow rate is set to “Auto”.
P.E-17
)
Operation Modes and Tips for Selection
Operation mode
Air Purify
(Green)
Pollen
(Green)
Strong Deodorization
(Green)
This is a normal operation mode.
The odor sensor and dust sensor detects the degree of air contamination, and airflow rate is switched automatically.
During auto sensor operation, airflow rate ranges from Silent to High.
This mode is recommended when you have concerns about pollen contamination.
The unit automatically operates while the odor sensor and the dust sensor sense the air contamination
level.
In the automatic operation, airflow level will be Silent to Med.
This mode is recommended when you have concerns about room odor.
The odor sensor and dust sensor detects the degree of air contamination and switches to the operation with higher airflow than Air Purify mode.
During auto sensor operation, airflow rate ranges from Low to Max.
In the first one minute, Max airflow operation is performed regardless of the level of air contamination.
Tips for Selection
Installation
Using Remote Controller
Humidify
(Orange)
Skin Moisturize
(Orange)
Note
Room air humidity is controlled to approx. 50%.
During auto sensor operation, airflow rate ranges from Silent to High.
Room air humidity is controlled to approx. 60%.
During automatic operation, airflow rate ranges from Silent to High.
During operation, vibrations from the unit may slightly rock the water in the water tank.
Selected operation mode indicator is lit.
Press
button.
On
Operation mode
switches every time
Operation mode switches every time you press Mode button.
Air Purify
Pollen
Strong Deodorization
Humidify
you press this button.
The airflow rate is set to “Auto” by switching the operation mode.
Skin Moisturize
E-11
Using Remote Controller (Continued)
Airflow rate
When “Auto” is lit, the following airflow rate is used according to the selected operation mode.
The airflow rate indicators from “Silent” to “Max” are not lit.
Mode
Air Purify
Pollen
Silent
Silent
Strong Deodorization
When humidity level indicates 60% or higher
Low
Low
Low
Airflow Range
Medium
Medium
Medium
High
High Max
Humidify
Silent
When humidity level indicates 70% or higher
Low
Medium
High
Skin Moisturize
Silent
According to the level of air contamination and humidity detected by the odor sensor, dust sensor and humidity
sensor, airflow rate is automatically switched to an appropriate level.
Low
Medium
High
Note
So far as the water tank and water tray are filled with water, humidifying function works in any of “Air Purify”,
“Pollen” and “Strong Deodorization” modes. If you do not want humidifying function, drain the water tank,
water tray and humidifying filter.
Switching Airflow Rate
You can select a desired airflow rate from the four different levels.
Press
Airflow rate switches every
time you press this button.
button.
Airflow level indicator comes on.
Air Purify
Auto
Airflow rate changes in the following sequence.
Strong
Deodorization
On
HumidifyPollen
Skin
Moisturize
Max(Blinking)
Auto
Silent Medium High Blinking
(Max)
E-12
Max Operation
This operation is useful when many people smoke or when you want quick cleaning of room air.
(Air Purify Mode)
Press button.
The operation with Max airflow
will continue for about 5 minutes.
After Max operation, the status
before Max operation is resumed.
It takes about 10 seconds until the air flow rate reaches Max.
Using Timer
Press
button.
The airflow indicator
Auto
blinks for 5 minutes.
Max(Blinking)
Blink
How to cancel
Press button or button during operation.
Using Remote Controller
The timer indicator is lit on.
Pollen
Strong
Deodorization
Humidify
Skin
Moisturize
Timer(4hrs)
Off-timer (4 hours) is set.
Operation will stop approx.
4 hours after timer setting.
How to set/cancel
Every time you press
“Cancel” will alternate.
On
button, “Set” and
E-13
)
Using the Control on Purifi er
Press
button.
Operation starts.
Every time you press
mode switches in the following sequence so that you
can choose a desired mode or stop.
Air
Purify
The airflow rate is set to “Auto” by switching the
operation mode.
Pollen
Strong
Deodorization
button, the operation
Humidify
Skin
Moisturize
Off
Memory Function / Sensors / Auto Detection
Memory Function
When you stop the operation and then restart, the purifi er will resume the operation status before shutdown.
If you operate the purifi er for approx. 5 seconds or longer, the operation status will be stored in memory.
(If you stop the operation within less than 5 seconds, the operation status will not be stored in memory.)
Even if you unplug the power cord, the operation status will be stored in memory. However, the airfl ow rate is
automatically set to “Auto”.
Air Sensor
Level of air contamination detected by the odor sensor, dust sensor is shown by the way the indicator is activated.
Indicator action : Lit in green Blink in green
Contamination level: Clean Contaminated
Note
You can adjust the air sensor, dust sensor sensitivity setting as desired.
In case the purifi er is installed in a place where air contamination is hard to detect
or in case the sensor itself is not clean, the indicator action may not change.
P.E-16
Skin
Moisturize
Max(Blinking)
P.E-25
Timer(4hrs)
Clean
Humidifying
Filter
Odor Sensor
The sensor detects odor in air such as cigarette smoke or odor of pet animals.
Even when you feel the air is clean, the purifier may continue the operation if the
odor sensor finds any gas component not removed by the filter.
Any of the following may also be detected by the odor sensor.
Combustion gas from heating appliance, alcohol, odor of perfumes or cosmetics
used in beauty parlor or aesthetic salon, sprays, vapor, abrupt temperature
change, etc.
Odor sensor
Air
Sensor
E-14
Dust sensor
Dust sensor is capable of sensing the dusts in the air such as cigarette smoke, house
dust, pollen, etc.
Dust sensor may fail to sense the dusts stirred up when you lay out or put away the
bedding, which are signifi cantly fewer contaminants than cigarette smoke, etc. In
such a case, the displayed air contamination level may appear to be lower.
Carry out the periodical cleaning every 3-6 months. Otherwise poor performance of
the dust sensor will result.
P.E-22
Dust Sensor
Humidity Sensor
The humidity sensor fi nds the humidity of room air during operation.
Humidity level should be taken as a guide only.
The indication may differ from hygrometer reading.
Humidity will change as temperature changes.
Humidity level may differ between well-ventilated and ill-ventilated places.
Humidity Sensor
Auto Detection
The air purifi er performs automatic operation by detecting room air contamination with “Odor Sensor” and
room air humidity with “Humidity Sensor”.
In the fi rst 3 minutes after the power cord is plugged in, the unit will check room air condition and save it
in memory. During the time, the “Air Sensor” indicator and “Humidity Level 50” indicator will blink. After
3 minutes, both the “Air Sensor” and “Humidity Level 50” indicators will go off and the purifi er is now
ready to operate.
You may start the operation in less than 3 minutes after plugging the power cord.
In this case too, the “Air Sensor” and “Humidity Level 50” indicators will continue to blink, meaning the
unit is checking room air condition. After 3 minutes, the indicators will show your room air conditions.
If you plug in the power cord under contaminated air condition, the sensor sensitivity may be reduced. In such a
case, perform High or Max operation. Or you may try to make the room air cleaner by opening a window before
plugging the power cord. If the sensor sensitivity remains low after this, change the sensor sensitivity setting.
Using the Control on Purifier Memory Function / Sensors / Auto Detection
E-15
g
Memory Function
/
Sensors / Auto Detection (Continued)
Adjusting Sensor Sensitivity Setting
Sensor sensitivity can be adjusted in 3-step fashion.
In each operation mode,
press button.
(Use the tip of a ball-point pen or
the like.)
The airflow indicator will blink
for 5 seconds.
While the airflow indicator is blinking,
press
The factory setting is “Medium”.
button.
Present setting is shown by the airflow
indicator that blinks for 5 seconds.
Air Purify
Auto
Every time you press the button, the setting switches.
Pollen
Strong
Deodorization
(Medium)(Low) (High)
Humidify
Blink
Skin
Moisturize
Max(Blinkin
E-16
Useful Feature
Eco Operation
In the eco operation mode, the unit automatically pauses when the air in the room is clean to save
money on electricity. Furthermore, if this state continues more than 8 hours, the unit automatically
stops operation. (In humidifying operations, the unit will not pause at a certain humidity level.)
Normal automatic operation
When the air is clean, the unit continuously operates at
“Silent” airfl ow. (In the strong deodorization mode, the
airfl ow rate is set to “Low”.)
Eco operation
When the air is clean and “Silent” operation continues
for 10 minutes or longer, the fan stops for about 50
minutes and the unit intermittently operates at “Silent”
airfl ow for about 10 minutes.
If this state continues more than 8 hours, the unit
automatically stops operation.
The degree of air contamination is detected by the odor sensor and dust sensor during eco operation. If the sensors detect
odor or dust, the airflow rate switches according to the degree of air contamination. When the air becomes clearer and the
unit runs for 10 consecutive minutes or longer at “Silent” airflow, the unit starts intermittent operation.
Press
button.
Silent
operation
Stop
10 minutes 10 minutes
Silent
operation
Stop
10 minutes
50 minutes 50 minutes
“eco” indicator is lit.
Air Purify
Pollen
Strong
Deodorization
Skin
MoisturizeHumidify
Memory Function / Sensors / Auto Detection Useful Feature
Max(Blinking)
The mode is set to eco operation.
Auto
On
How to set/cancel
Every time you press button, "Set" and
"Cancel" will alternate.
The settings are stored.
Note
When using the air purifier together with the Hitachi air purifier with ionizing function
Pressing the button on the remote controller in front of the Hitachi air purifier with ionizing function (model whose
ionization setting / release is switched using the remote controller) sets and releases ionization. Furthermore, pressing
the ionizing button on the remote controller of the model with the ionizing function sets and releases eco operation.
Dimmer Control
If you feel uncomfortable about indicator lightings when you go to sleep, press button on the
purifier unit for 3 seconds or longer to dim the indicators.
Press button for 3 seconds
or longer.
The indicators are dimmed.
How to set/cancel
Every time you press button, “Set”
and “Cancel” will alternate.
The setting will be saved in memory.
E-17
Cleaning
Before cleaning, be sure to stop operation and unplug the power cord from AC outlet.
Do not splash water on the purifier body. Water splash can be a cause of failure.
Do not use a volatile solvent, such as gasoline, thinner, benzene, wax, kerosene, alcohol, etc. or
WARNING
CAUTION
When the “Clean Humidifying Filter” indicator is lit, clean the humidifying filter, water tray and tray cover. The
“Clean Humidifying Filter” indicator will come on approx. one month (approx. 720 hours) after the start of use
or after the reset button was pressed upon finishing previous cleaning. Depending on the tap water used,
water scale may adhere earlier. If the filter contamination is heavy, clean the filter more than once a month
before the “Clean Humidifying Filter” indicator is lit.
When you are done with cleaning, press the reset button. The “Clean Humidifying Filter” indicator will go off.
When the “Clean Humidifying Filter” Indicator Comes On
polishing powder, or detergent (neither kitchen nor laundry use).
Such chemicals could cause deformation, discoloration, damage or removal of prints.
Do not tilt or tip over the unit.
When using a chemically treated cloth, follow its instructions.
Never use dryer or heater to dry the purifier case. Heating could cause deformation, discoloration,
damage or removal of prints.
Lay a soft cloth or the like beneath the purifier to protect the floor against scratch.
Remove the water tank, and then
pull out the water tray.
Water tray
Slowly pull out the
water tray while lifting
it obliquely upward.
When you pull out the water tray, water may spill out or the floor may be scratched with
CAUTION
bottom of the tray. Lay a soft cloth or the like beneath the purifier to protect the floor.
P.
E-9
Clean the humidifying filter, water tray and tray cover.
When the purifier body is shaken or rocked, water may gather in other part of the water tray not to be
fitted with the humidifying filter.
After you pulled out the water tray, be sure to remove the tray cover and wipe off water or clean it.
Set the humidifying filter.
Slowly insert the humidifying filter into the tray cover.
Insert the filter fully until it comes into positive contact
with bottom of the tray. Inadequate fitting may cause
water leakage during operation.
Remove the humidifying filter from
the water tray.
Humidifying fi lter
手前
手前
Marking
Water tray
P.
E-19, E-20
Humidifying fi lter
手前
E-18
Install the water tray, and then
mount the water tank.
Plug the power cord in AC outlet
and press the reset button located
behind the panel.
Press the reset button located behind the panel.
(Use the tip of a ball-point pen or the like.)
Check that the “Clean” indicator is now OFF.
Mount the panel on the unit.
P. E -
8
Remove the panel.
Reset button
P.E-
8
“Clean” indicator (Red)
Water Tank (Guide for cleaning: Daily)
ᚻ೨
ᚻ೨
Change water daily with fresh tap water.
Discard remaining water in the tank if any.
Pour small quantity of tap water, tighten the cap firmly and shake to wash.
(Change water and repeat the steps 2-3 times.)
WARNING
CAUTION
Do not use detergents (neither kitchen nor laundry use) for cleaning.
Do not push in the pin at the cap center. Doing so may cause water leakage.
Be sure to stop operation before removing the water tank.
Do not set the water tank without having the water tray in place. Otherwise, the water tank may tip over.
When you remove the water tank, water may drip from the tank cap.
Humidifying Filter (Guide for cleaning: Once a month)
The humidifying system employed in this product is of evaporating type that produces moisturized air by
passing air stream through the humidifying filter.
Depending on application environment, dirt or odor may adhere to the humidifying filter even when the
“Humidify” or “Skin Moisturize” mode is not performed.
When "Humidify" or "Skin Moisturize" mode is used, be sure to pour tap water into the water tank.
Although the humidifying filter has been given anti-bacterial and anti-mold processing, it may get slimy or moldy,
or may be discolored to pink, red, green, brown or gray within a short period of use depending on the quality of
tap water used and application environment. (Discoloration has no effect on humidifying performance.)
It is recommended to clean the filter as often as practicable regardless of whether the “Clean
Humidifying Filter” indicator is lit on or not.
Early replacement of the filter is recommended if it exhibits any of the following conditions despite periodical cleaning.
Heavy dirt, adhering water scale too hard to remove, harsh odors, damage or deformation
If you do not use the “Humidify” or “Skin Moisturize” mode, drain the water tank and water tray.
Remaining water can be a cause of dirt or discoloration.
Do not disassemble the humidifying filter and its casing.
Submerge the
humidifying filter in any
of water, lukewarm water
or water with neutral
kitchen detergent for
30 minutes or longer.
Do not disassemble the humidifying filter and its case.
When you use neutral kitchen detergent, follow
the instructions given by the manufacturer.
(Only use neutral kitchen detergent.)
Change the water
and rinse the
humidifying filter by
shaking it.
(Repeat the steps
2-3 times.)
When you use neutral kitchen
detergent, rinse the filter well so that
no detergent remains.
Shake lightly to drain off water.
(Continue until no more dripping
ᚻ೨
Cleaning
occurs.)
As you operate the air purifier, whitish or brownish water scale will adhere inside of the water tray or to
the humidifying filter surface. Water scale is the remnant of minerals in tap water that has not evaporated.
If you continue to use the filter without cleaning the water scale, it will get hard and difficult to remove,
resulting in lower humidifying performance.
Depending on the quality of tap water used, water scale may adhere quickly.
In such a case, the cleaning should be done sooner.
When you rinse the humidifying filter, rinse it as assembled with its case. Do not remove the case.
(Removing the case may cause deformation or damage.)
Do not scrub the humidifying filter with brush or press forcibly to deform.
(It may cause damage and deterioration of performance.)
New humidifying filter may smell at the beginning. This is normal.
Replace the filter early if it is damaged.
CAUTION
Washing the humidifying filter with citric acid will deteriorate the anti-bacterial and anti-mold performance.
Do not install the humidifying filter if containing too much water. It may cause water leakage.
E-19
Cleaning (Continued)
Replacing Humidifying Filter
The humidifying fi lter is a consumable part. Replace it using 24 months of use as a guide (cleaning is
needed once in every month).
Early replacement of the fi lter is recommended if it exhibits any of the following conditions despite periodical cleaning.
Heavy dirt, adhering water scale too hard to remove, harsh odors, damage or deformation
Depending on the quality of tap water used, the humidifying fi lter may be consumed extremely early.
Detach the case and replace the humidifying fi lter.
Do not dispose of the humidifying filter case.
To detach the case, push the 3 tabs.
Detach the case by opening in
directions.
Tab
手前
手前
Tab
Replacement humidifying fi lter
No. EP-DX40E-908
The humidifying filter is flammable. Dispose of the filter according to local regulations.
Water Tray / Tray Cover
(Guide for cleaning: Once a month)
Do not use any detergent.
Remove the tray cover.
Remove the tray cover from the water
tray.
Tray cover
Water tray
Wash with water to remove dirt.
Drain water remaining on the try.
Use cotton swab or tooth brush to remove
dirt in the narrow parts.
Humidifying fi lter
E-20
Wipe off water and assemble.
Attach the tray cover to the water tray.
WARNING
CAUTION
Do not use any detergent (neither kitchen nor laundry use).
When you mount the water tray on the unit, the tray should be empty.
Tray cover
Water tray
Otherwise water may spill out.
Pre-filter
To clean the pre-fi lter, follow the steps below.
(Guide for cleaning: Once a month)
Remove the water tank, and then pull out the water tray.
(This is to prevent water leakage.)
When you remove the tank, water may drip from the tank cap. Lay a dry cloth
CAUTION
Remove the panel.
before removing the water tank.
P.E-8
Remove the pre-filter.
Disengage the four tabs of the pre-fi lter.
Pre-filter tab insertion
section
Clean the pre-filter.
Use a vacuum cleaner or the like to remove dust. If the dust
cannot be removed, wash off with water. After washing, fully
drain the pre-fi lter and then dry it in a well-ventilated place
not exposed to sunlight.
When you wash, use a soft toothbrush or the like.
Vacuum
cleaner
attachment
for
cleaning
shelves
P.E-9
Pre-filter
Dust filter
deodorizing
filter
If you want to remove dust on the Dust fi lter / deodorizing
fi lter, use a vacuum cleaner. The Dust fi lter / deodorizing fi lter
is not washable.
Reattach the pre-filter.
Insert the four tabs securely into the holes on the purifier
and fi x the pre-fi lter.
Pre-filter tabs
Reattach the panel.
Install the water tray, and then mount the water tank.
The pre-fi lter is a consumable part.
When damaged pre-filter needs to be replaced, purchase the replacement part (Part No. EP-DV1000-002).
P.E-8
P.E-9
Cleaning
E-21
Cleaning (Continued)
Purifier Body
Wipe off dirt on the purifi er case using a soft cloth that is moistened
with water and fully wrung. For heavy dirt, use a soft cloth moistened
with neutral detergent thinned with water. After removing dirt, use a dry
soft cloth to wipe off moisture so that no detergent will remain.
To clean the remote infrared receiver, use a thin cotton swab slightly
moistened with water to wipe off dirt. After that, use a dry cotton swab
to remove the moisture.
Remove dust on the surfaces of the panel, air inlet, odor sensor, dust
sensor section and humidity sensor using a vacuum cleaner attachment
for cleaning shelves. Then wipe off with a soft cloth.
Panel
Vacuum cleaner attachment
for cleaning shelves
Dust sensor
Carry out the periodical cleaning every 3-6 months.
Otherwise poor performance of the dust sensor will result.
(Guide for cleaning: Once a month)
Dust sensor section
Humidity sensor
Remote infrared receiver
(Cleaning guide: every 3-6 months)
Remote infrared
receiver
Odor sensor
Remove the dust sensor cover.
Do not wipe the lens forcibly. It may cause damage.
Do not disengage and engage the tabs of the dust sensor cover forcibly.
CAUTION
It may cause damage.
Wipe the lens with a cotton swab.
Soak a cotton swab with a little water
and wipe off any heavy dirt with it.
After cleaning the dust sensor,
reinstall the dust sensor cover.
Lens
E-22
Filter Replacement
Replacement Interval
The fi lters are consumable parts. The standard life of the dust fi lter is about 8 years and that of the
deodorizing fi lter is about 10 years. Testing was conducted according to JEM1467 of the Japan Electric
Machine Industry Association. If 5 cigarettes are smoked per day:
[Dust fi lter] Years until the air purifying time is double that of when the fi lter is new
[Deodorizing fi lter] Years until the deodorizing rate is reduced in half when the fi lter is new
The dust fi lter should be replaced early if its color shows the resemblance to the color on the dirtiness
label attached to the purifi er body.
The colors on the dirtiness label are shown as a guide only. Depending on the place of installation, actual
color of contaminated filter may differ from the color shown on this label.
For a room with
not much cigarette
smoking
For a room with
much cigarette
smoking
For the deodorizing fi lter replacement interval, use approx. 10 years as a guide. Replace the fi lter
earlier any time the fi lter performance is degraded.
The fi lter may need to be replaced earlier depending on the place of installation and conditions of use.
When dirt or odor becomes harder to remove, replace the fi lter earlier than suggested. Otherwise, the
fi lter may generate odor.
The fi lter should be replaced earlier in the following cases.
When purifier intakes oily smoke, carbon substance (soot), etc. or when the smell of new building materials
remains after a new house is built or the house is remodeled.
When used in stores, such as in coffee shops, game parlors, barber shops, beauty parlors, or in offices or hotels·
inns.
When purifier intakes large amounts of cigarette smoke.
When purifier intakes combustion gas generated by heating appliances.
When purifier intakes solvent content of paint, adhesive, etc.
When used in dusty place near a road where the traffic is heavy.
Dirtiness label
Filter Replacement Guide
Replace the filter
early if its color
becomes similar to
either color.
Precautions on Filter Handling
Be sure to take the fi lter out of a plastic bag before use.
Do not set the filter when it is still in a plastic bag. Otherwise, malfunction may result.
Avoid rough handling.
Do not crush, knead or roll the filter.
Once the filter is broken, the cleaning effect will be lost.
Do not wash the fi lter.
The filter is not washable for reuse. Purchase a new filter for replacement.
The fi lter contains plastics inside. When you dispose of the fi lter, follow relevant local regulations on
disposal.
Cleaning Filter Replacement
E-23
Filter Replacement (Continued)
Replacing the Filter
For the fi lters, use the optional EP-A6000-902 (dust fi lter) and EP-A6000-903 (deodorizing fi lter).
Use a genuine fi lter for the Hitachi Air Purifi er.
CAUTION
Before replacing the fi lter, be sure to stop the purifi er and unplug the power cord from AC outlet.
Other filters may cause unit failure.
Remove the water tank, and then pull out the water tray.
(This procedure should be done to prevent water leakage.)
When you remove the water tank, water may drip from the tank cap.
CAUTION
Lay a dry cloth before removing the water tank.
Remove the panel and the pre-filter.
Remove the used filter.
Remove the dust fi lter and then the deodorizing fi lter.
Take a new deodorizing filter
out of its plastic bag and
install it on the unit.
Install the deodorizing fi lter so that its black
surface faces the front (white surface in the
back).
Insert the fi lter all the way until the label
(deodorizing fi lter position indicator) is hidden.
P.E-8
P.E-9
P.E-8
Deodorizing filter
Dust filter
The back
(White)
front side(Black)
CAUTION
Be sure to take the fi lter out of its plastic bag.
Do not block the fi lter front surface with
cloth or paper.
Same precautions should be taken for the
dust fi lter as well.
Take a new dust filter out of its
plastic bag and install it on the unit.
P.E-8
Insert the filter all the way until the label (dust filter
position indicator) is hidden.
Install the pre-filter.
Reinstall the panel on the unit.
Install the water tray, and then mount the water tank.
P.E-8
Deodorizing filter
(Black surface)
Dust filter
P.E-9
White
surface
Deodorizing filter
E-24
Note
No cleaning effect is obtainable if the fi lter is installed with plastic bag.
It may also be a cause of malfunction.
Alert Display
Symptom
Cause
All airflow indicators are blinking. Faulty fan rotation.
Stop the operation, unplug the power cord from AC outlet and contact your dealer for service.
Troubleshooting Guide
Before asking for repair
Symptom Solution
Is power plug securely inserted
No air blows out
or power does
not turn on
Smoke or smell
into AC outlet?
Is breaker switched off?
Is the pre-filter dirty?
is not efficiently
removed, or
Is the filter dirty?
there is an odor
Check to see
check the following once again
Securely insert the power plug into AC
outlet.
Switch on breaker.
Clean the pre-filter, referring to the “Prefilter” in “Cleaning”.
Replace the filter, referring to the “Filter
Replacement”. The filter may need to be
replaced sooner depending on the place of
installation and conditions of use.
P.
E-21
P.E-23
No remote
operation
Airflow rate
does not
decrease even
though the air is
clean
Airflow rate
does not
increase even
though the air is
contaminated
Are polarities of batteries
correct?
Are batteries dead?
Is the remote infrared receiver
dirty?
Is airflow rate switched?
Is the operation in the
“Humidify” mode?
Is sensor sensitivity high?
Is airflow rate switched?
Is odor sensor hole blocked by
dust or other obstacle?
Is sensor sensitivity low?
Was the ambient air clean when
the purifier power cord was
plugged into AC outlet?
Insert the batteries with correct
polarities.
Replace the batteries.
Clean the remote infrared receiver.
Press the airflow button and select Auto
Sensor or other airflow rate.
Airflow rate will not decrease when humidity
is low.
Change the sensor sensitivity
setting.
Press the airflow button and select Auto
Sensor or other airflow rate.
Clean the odor sensor.
Change the sensor sensitivity
setting.
Change the airflow rate. Or open a window
and plug the power cord into AC outlet
when ambient air is clean.
P.E-11
P.E-11
P.
P.
P.
,E-
P.
-E-
P.
P.
P.
E-9
E-9
E-22
14
E-16
14
E-22
E-16
E-15
Filter Replacement Alert Display Troubleshooting Guide
“Air Sensor” indicator
is kept constantly lit
in green
“Air Sensor”
indicator is kept
blinking in green.
Is the purifier installed in a place
out of reach of odor or dust?
Is odor sensor hole blocked by
dust or other obstacle?
Is the dust sensor covered with
dust?
Is odor sensor hole blocked by
dust or other obstacle?
Relocate the air purifier.
Clean the odor sensor.
Clean the dust sensor.
Clean the odor sensor.
P.
P.
E-22
E-22
E-25
Troubleshooting Guide (Continued)
Symptom SolutionCheck to see
Is there anything nearby that the
“Air Sensor”
indicator is
kept blinking in
green.
No humidifying
effect
Humidifying
performance is
inadequate when
operated in the
“Humidify” mode
odor sensor might sense?
Any appliance generating combustion gas
Alcohol, cosmetics, sprays, etc.
Is odor sensor hole blocked by
dust or other obstacle?
Is there water in the water tank?
Is the operation in any of the “Air Purify”,
“Pollen” or “Strong Deodorization” mode?
Is the humidifying filter dirty?
Is the airflow rate set to “Auto”?
Is the pre-filter or the filter
dirty?
Purifier may sense invisible gas component
that cannot be cleaned by filter and
continue operation. Ventilate the room by
opening window, etc.
Clean the odor sensor.
Fill the water tank with water.
Change the operation mode to the “Humidify”
or “Skin Moisturize” mode.
Clean or replace the humidifying filter,
referring to the “Humidifying Filter” in “
Cleaning”.
Depending on the place of installation and
conditions of use, water may not be consumed.
Set the operation mode to “Skin Moisturize”
and the airflow rate to “High” or “Max”.
P.E-11,E-12
Clean the pre-filter, referring to
“Pre-filter” in “Cleaning”.
P.
E-15
P.
E-22
P.
E-9
P.
E-11
P.
E-19
P.E-21
Is the humidifying filter set
properly, or is it dirty?
Is there water in the water tank
When operated in “Air
Purify”, “Pollen” or
“Strong Deodorization”
mode, air is humidified
Water leaks
Indicator is dim
and water tray?
Is the humidifying filter wet with
water?
Is the water tank set properly?
Is the tank cap closed firmly, or
the tank cap packing set securely?
Is the water tray cover closed
properly?
Is the humidifying filter set
securely?
Is the purifier tilted, or was it
carried with water in the tank?
Is there an opening in the water
tank or water tray?
Is there any leakage from the
water tank?
Is dimmer control activated?
Set the humidifying filter properly. If it is
dirty, clean or replace it.
Discharge water and then operate.
Drain the humidifying filter.
Set the water tank properly.
Close the tank cap firmly.
Close the water tray cover properly.
Set the humidifying filter securely.
Place the purifier on a level, stable surface.
Avoid carrying the purifier with water in the tank.
Stop using the purifier immediately and
contact your dealer for repair.
Stop using the purifier immediately and
contact your dealer for repair.
Cancel the dimmer control setting.
P.E-18-E-20
P.E-9
P.E-9
P.E-18
P.E-17
The “Clean Humidifying
Filter” indicator does
not go off
E-26
Was the reset button pressed
after cleaning?
Press the reset button.
P.E-18
Following Conditions Are Normal
Symptom Cause
Snapping noise when plugging power cord
into AC outlet
Purifier body vibration during the “Max” operation
No vapor or mist visible
Bubbling noise
Humidity level indication differs from hygrometer
reading
Shutter is stopped midway
Clicking noise during operation
Rocking water surface in the water tank
Indicators repeatedly turn on and off one after
another, and the fan is stationary
Electric components are energized when
power is supplied. This is normal.
Vibration is caused by fan rotation. This
is normal.
As the unit employs evaporation system that produces
moisturized air by passing air stream through the
humidifying filter, no vapor or mist is visible.
The noise is produced by air bubble when water in the
water tank is supplied to the water tray. This is normal.
Humidity level is indicated as a guide
only. Also an environmental difference in
the room may cause different indications.
There is no problem in performance even if
the shutter is not fully opened. This is normal.
It is a switching sound of the shutter. This
is normal.
It is caused by vibration during operation.
This is normal.
The unit is in the demo mode. Unplug the
power cord once, wait for a few seconds,
and then insert the power plug into AC
outlet.
This is normal.
Pressing the eco button operates the ionization
setting / release of the other Hitachi air purifier
with ionizing function.
Or, pressing the ionizing button on the remote
controller for the other Hitachi air purifier with
ionizing function operates the setting / release
of eco operation.
The fan is stopped.
The signals from the remote controllers
are the same. Both functions respond.
This is normal.
When eco operation is selected, the fan
may stop.
P.E-17
Troubleshooting Guide
E-27
Replacement Parts (Separately Available)
Dust Filter
Designate the replacement part
No. EP-A6000-902 when ordering.
Pre-filter
Designate the replacement
part No. EP-DV1000-002 when
ordering.
Tank Cap
Designate the replacement part
No. EP-BV60-017 when ordering.
Specifications
Model EP-A7000
Deodorizing filter
Designate the replacement part
No. EP-A6000-903 when ordering.
Humidifying Filter
Designate the replacement part
No. EP-DX40E-908 when
ordering.
The case is not included.
Power supply AC220-240V 50-60Hz
Airflow switching Max High Medium Silent
Power consumption (W) 60 22 14 4
Airflow rate (m3/min) 7.0 4.5 3.4 1.0
Applicable floor space 50m
Humidifying performance (mL/h)
External dimensions 584(H) x 430(W) x 273(D) mm
Weight 10kg
Length of power cord Approx. 1.8m
Approx. 670 (Max operation)
2
E-28
Loading...