Hitachi ED-X8255F User Manual

Projector

ED-X8255

User's Manual – Operating Guide

Thank you for purchasing this projector.

WARNING ►Before using this product, please read the "User's Manual Safety Guide" and related manuals to ensure the proper use of this product. After reading them, store them in a safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING This symbol indicates information that, if ignored, could possibly

result in personal injury or even death due to incorrect handling.

CAUTION This symbol indicates information that, if ignored, could possibly

result in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.



NOTE • The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Trademark acknowledgment

• VGA and XGA are registered trademarks of International Business Machines Corporation.

• Apple and Mac are registered trademarks of Apple Computer, Inc.

• VESA and SVGA are trademarks of Video Electronics Standard Association.

• Windows is a registered trademark of Microsoft Corporation.

All other trademarks are the properties of their respective owners.

Content

 

About this manual . . . . . . . . . . 1

Content . . . . . . . . . . . . . . . . . . 2

Projector features . . . . . . . . . .

Preparations . . . . . . . . . . . . . .

About contents of package . . . . . . . 3

Fastening the lens cover . . . . . . . . . 3

Part names

. . . . . . . . . . . . . . . 4

Projector . . . . . . . . . . . . . . . . . . . . . 4

Control buttons . . . . . . . . . . . . . . . . 6

Remote control . . . . . . . . . . . . . . . . 6

Setting up . . . . . . . . . . . . . . . . 7

Arrangement . . . . . . . . . . . . . . . . . . 8

Adjusting the projector's elevator . . 9

Using the Security Bar . . . . . . . . . . 10

Connecting your devices . . . . . . . . .11

Connecting power supply . . . . . . . 14

Remote control . . . . . . . . . . .

Putting batteries . . . . . . . . . . . . . . 15

Using the remote control . . . . . . . . 16

Power on/off

. . . . . . . . . . . . . 17

Turning on the power . . . . . . . . . . .

Turning off the power . . . . . . . . . . .

Operating

. . . . . . . . . . . . . . . 18

Adjusting the volume . . . . . . . . . . . 18

Temporarily muting the sound . . . .

Selecting an input signal . . . . . . . . 18

Searcting an input signal . . . . . . . . 19

Selecting an aspect ratio . . . . . . . . 19

Adjusting the zoom and focus . . . . 19

Using the automatic adjustment feature

Adjusting the position . . . . . . . . . . 20

Correcting the keystone distortions

Using the magnify feature . . . . . . . 21

Freezing the screen . . . . . . . . . . . . 22

Temporarily blanking the screen Operating the computer screen . . . 23

Multifunctional settings . . . . 24

Using the menu function . . . . . . . . 24

3 3

17 17

. 20

. . 21

. . 22

EASY Menu . . . . . . . . . . . . . . . . . . 25

Aspect, Keystone, Mode, Brightness, Contrast, Color, Tint, Sharpness, Whisper, Mirror, Reset, Filter time, Language, Go to advanced menu

PICTURE Menu . . . . . . . . . . . . . . . 27

Brightness, Contrast, Gamma, Color temp, Color, Tint, Sharpness, Progressive, My memory

IMAGE Menu . . . . . . . . . . . . . . . . . 30

Aspect, Over scan, V. position, H. position, H. phase, H. size, Auto adjust execute

INPUT Menu . . . . . . . . . . . . . . . . . 32

Color space, Component, Video format, Frame lock, Information

SETUP Menu . . . . . . . . . . . . . . . . . 34

Keystone, Whisper, Mirror, Volume, Audio

SCREEN Menu . . . . . . . . . . . . . . . 35

Language, Menu position, OSD bright., Blank, Start up, MyScreen, MyScreen lock, Message

OPTION Menu . . . . . . . . . . . . . . . . 38

search, Auto off, Lamp time,

Auto

Filter time, Service

NETWORK Menu . . . . . . . . . . . . . 40

Dhcp, IP address, Subnet mask, Default gateway, Date and time, Time difference, e-shot, Information

Maintenance . . . . . . . . . . . . . 43

Lamp . . . . . . . . . . . . . . . . . . . . . . . 43

Air ﬁlter

. . . . . . . . . . . . . . . . . . . . . 45

Replacing Internal Clock battery . . 47

Other care . . . . . . . . . . . . . . . . . . . 48

Troubleshooting

. . . . . . . . . . 49

Related messages . . . . . . . . . . . . . 49

Regarding the indicator lamps . . . . 50

Phenomena that may easily be

mistaken for machine defects . . . . 52

Warranty and after-service

Speciﬁcations . . . . . . . . . . . .

. . . 55

Projector features / Preparations

Projector features

This projector is used to project various computer signals as well as NTSC/PAL/ SECAM, Component (SD, HD) video signals onto a screen. It requires just a little space for installation and gets a large image from short distance.

High Brightness



Newly developed 180W UHB (Ultra High Brightness) lamp gives you a higher brightness image on a screen. The image can be still kept as bright and clean enough for use in bright rooms.

Low Noise



WHISPER function is available for reducing acoustic noise to realize quieter operation. It is perfect for use in low luminance rooms where low noise is more important than brightness.

Rich Connectivity



This projector has a variety of I/O ports. It can be easily connected to many signal sources like PC, DVD and so on. The rich connectivity provides you more options to make your presentation impressive.

Compact Body



Even with its many features, this projector is extremely compact and slim, which gives you more ﬂexibility and usability to use it where you want.

Preparations

About contents of package

Please see the "Contents of package" of the "User's Manual - Quick Guide". Your projector should come with the items shown there. Contact immediately your dealer if anything is missing.

NOTE

moving the projector, be sure to use the original packing materials. Use special

caution for the lens part.

• Keep the original packing materials for future reshipment. For

Fastening the lens cover

To avoid losing the lens cover, please fasten it the lens cap to the projector using the strap.

Strap ring

Strap

Fix the strap to the strap ring of the lens cover.

Put the strap into the groove on the rivet.

Push the rivet into the strap hole.

Bottom side

Strap hole

Part names

Projector



Control buttons (6)

Lamp cover (44) (Lamp unit is inside.)

Zoom ring (19) Focus ring (19)

Vent (



Lens (17)

Lens cover (3)



Front-Right side

Bottom side

Remote sensor (16)

Speaker

Security bar (10) (Use for attaching a commercial anti-theft chain or wire.)

Elevator button (9) Elevator foot (9)

Filter cover (45) (Air ﬁlter and intake vent are inside.)

WARNING ►During use or immediately after use, do not touch around the

lamp and vents of the projector. () It could cause a burn.

Y R

AUDIO IN

AUDIO OUT

CONTROL RGB IN

RGB IN

USB

RGB OU

AUDIO IN1

LAN

LINK

VIDE

S-VIDEO

CB/PB

CR/PR

Part names

Power switch (17)

AC inlet (14)

Ports (See below.)

CONTROL port (12)

AUDIO-OUT port (

AUDIO IN2 L/R port (13) (In the default setting, the AUDIO IN2 L/R port is the audio port for the VIDEO, S-VIDEO and COMPONENT VIDEO ports, however it is possible to change the settings. 34)

COMPONENT VIDEO ports (13)

CB/P

CR/P

VIDEO port (13)

S-VIDEO port (13)

AUDIO IN1 port (12) (In the default setting, the AUDIO IN1 port is the audio port for the RGB IN1 and RGB IN2 ports, however, it is possible to change the settings. 34)

Elevator button (9)

Elevator foot (9)

Rear-Left side

12)



Restart switch (*) (48)

RGB IN1 port (

Vent (



)

RGB IN2 /RGB OUT port ( (Use the RGB IN OUT switch to select RGB IN2 or RGB OUT for this port.) RGB IN2 port: Inputs the RGB signal from a PC. RGB OUT port: When connected to a monitor, outputs the signal input via RGB IN1.

USB port (12)

Ports

RGB IN OUT switch (



12) Use this button to select either RGB IN2 or RGB OUT for the corresponding port. When this switch is not pushed in, RGB IN2 is selected. When this switch is pushed in, RGB OUT is selected.

LAN Port (12) Used for Ethernet input/output. This port is used when utilizing network functions.



12)

NOTE (*) About Restart switch: This projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly and the microprocessor will need to be reset. In such a case, please push the Restart switch by using a cocktail stick or similar, and before turning on again, make the projector cool down at least 10 minutes without

operating. Only push the Restart switch in these exceptional instances.

Part names

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARC

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTE

RESE

Control buttons

Cursor buttons ▲,▼,◄,► (24)

STANDBY/ON button

(17)

Remote control

LAMP indicator (50, 51) TEMP indicator (



50, 51)

POWER indicator (17)

INPUT button (



18)

SEARCH button (19)

RGB button (18)

VIDEO button (19)

ASPECT button (

HOME button (23)

MAGNIFY ON button (21) OFF button (21)

END button (23)

FREEZE button (22)

POSITION button (20)

ESC button (24)

Battery cover (15) (on the back)

STANDBY/ON button (

AUTO button (



17)

20)

BLANK button (22)

19)



PAGE UP button (



23)

VOLUME button (18)

MUTE button (18)

PAGE DOWN button (

KEYSTONE button (



23)

21)

MENU button (24)

Cursor buttons

▲,▼,◄,► (24)

ENTER button (24)

RESET button (



24)

Setting up

WARNING ►Place the projector in a stable position horizontally. A fall or a turnover could cause an injury and/or damage to the projector. Then using damaged projector could result in a ﬁre and/or an electric shock.

• Do not place the projector on an unstable, slant or vibrant surface such as a

wobbly or inclined stand.

• Do not place the projector in the side/front/rear-up position, except cleaning

the air ﬁlter. ►Place the projector in a cool place, and pay attention enough to ventilation. The high temperature of the projector could cause a ﬁre, a burn and/or malfunction to the projector.

• Do not stop up, block and cover the projector's vents.

• Keep a space of 30 cm or more between the sides and other objects such as

walls.

• Do not place the projector on a metallic thing or anything weak in heat.

• Do not place the projector on a carpet, cushion or bedding.

• Do not place the projector in direct sunlight or near a hot object such as a

heater.

• Put nothing about lens and vents of the projector. Put nothing on the projector.

• Put nothing that is sucked or sticks to the bottom of projector. This projector

has some intake vents also on the bottom. ►Do not place the projector on the place that gets wet. Damping the projector or inserting liquid in the projector could cause a ﬁre, an electric shock and/or malfunction to the projector.

• Do not place the projector in a bathroom or the outdoors.

• Put nothing containing the liquid near the projector.

CAUTION ►Avoid a smoky, humid or dusty place. Placing the projector in such place could cause a ﬁre, an electric shock and/or malfunction to the projector.

• Do not place the projector near a humidiﬁer, a smoking space or a kitchen. ►Adjust the direction of the projector to keep the light from directly hitting the projector's remote sensor.

Setting up

Arrangement

Refer to the illustrations and tables below to determine the screen size and projector distance. The values shown in the table are calculated for a full size screen:1024×768

(a) The screen size (diagonal) (b) Distance from the projector to the screen (±10%) (c) The height of the screen (±10%)

(b)

4:3

(a)

(a) Screen

size

[inch (m)]

30 (0.8) 0.9 (36) 40 (1.0) 1.2 (48) 1.5 (58) 6 (2) 55 (22) 1.3 (52) 1.6 (63) -2 (-1) 51 (20) 50 (1.3) 1.5 (60) 1.8 (73) 8 (3) 69 (27) 1.7 (66) 2.0 (79) -2 (-1) 64 (25) 60 (1.5) 1.8 (73) 2.2 (87) 9 (4) 82 (32) 2.0 (79) 2.4 (95) -2 (-1) 77 (30) 70 (1.8) 2.2 (85) 2.6 (102) 11 (4) 96 (38) 2.4 (93) 2.8 (111) -3 (-1) 90 (35) 80 (2.0) 2.5 (97) 3.0 (117) 12 (5) 110 (43) 2.7 (106) 3.2 (127) -3 (-1) 103 (41)

90 (2.3) 2.8 (109) 3.3 (132) 14 (5) 123 (49) 3.0 (119) 3.6 (143) -4 (-1) 116 (46) 100 (2.5) 3.1 (122) 3.7 (146) 15 (6) 137 (54) 3.4 (133) 4.0 (159) -4 (-2) 129 (51) 120 (3.0) 3.7 (146) 4.5 (176) 18 (7) 165 (65) 4.0 (159) 4.9 (192) -5 (-2) 154 (61) 150 (3.8) 4.6 (183) 5.6 (220) 23 (9) 206 (81) 5.1 (200) 6.1 (240) -6 (-2) 193 (76) 200 (5.1) 6.2 (244) 7.5 (294) 30 (12) 274 (108) 6.8 (266) 8.1 (320) -8 (-3) 257 (101) 250 (6.4) 7.8 (306) 9.3 (367) 38 (15) 343 (135) 8.5 (333) 10.2 (400) -10 (-4) 322 (127) 300 (7.6) 9.3 (367) 11.2 (441)

(b) Projection distance

[m (inch)]

min.

1.1 (43)

16:9

(a)

4 : 3 screen

max. down

5 (2)

46 (18)

[cm (inch)]

41 (16)

411

(b) Projection distance

(162)

min.

1.0 (39)

10.2 (400) 12.2 (480)

16 : 9 screen

[m (inch)]

max. down up

1.2 (47)

-1 (0) 39 (15)

-12 (-5) 386 (152)

[cm (inch)]

Setting up

Adjusting the projector's elevator

CAUTION ►If you press the elevator button without holding the projector,

the projector might crash down, overturn, smash your ﬁngers and possibly result in malfunction. To prevent damaging the projector and injuring yourself, always hold the projector whenever using the elevator buttons to adjust the elevator feet. ►Do not incline the projector rightward or leftward. Also do not incline it backward or forward exceeding 9 degrees. Exceeding these range could cause malfunction, and could shorten the lifetime of the consumables. ►Except for inclining by the elevator feet adjustment, place the projector horizontally.

You can use the elevator feet to make adjustments if the surface on which you need to set the projector is uneven or if you otherwise need to adjust the angle of projection. The adjustment range of the elevator feet is 0 to 9 degrees.

Elevator feet

After making sure that the projector is cool adequately, press and hold in the

elevator buttons while holding the projector.

The elevator buttons and the elevator feet are on the both sides.

Raise or lower the projector to the desired height and release the elevator

buttons.

When you release the elevator buttons, the elevator feet will lock into position.

If necessary, you can also ﬁnely adjust the height of the projector by twisting

the elevator feet by hand.

Elevator button

Setting up

Using the Security Bar

WARNING ►Do not use the security bar to prevent the projector from

falling. Dropping or knocking over the projector may cause damage or injury.

CAUTION ►The security bar is not a comprehensive theft prevention

measure. It is intended to be used as an extra theft prevention measure.

A commercial anti-theft chain or wire can be attached to the security bar on the projector.

How to attach

An anti-theft chain or wire can be attached as shown in the illustration. (Anti-theft chains or wires of up to 10mm in diameter can be used)

Security Bar

Anti-theft chain or wire [sold separately]

Setting up

Connecting your devices

CAUTION ►Turn off all devices prior to connecting them to the projector.

Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector. ►Use the accessory cable or a designated-type cable for the connection. Some cables have to be used with core set. A too long cable may cause a certain picture degradation. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector. ►Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector.

NOTE • Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop’s RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer instruction manual of the corresponding laptop computer.

• Secure the screws on the connectors and tighten.

• Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

• For some RGB signal modes, the optional Mac adapter is necessary.

• When the image resolution is changed on a computer, depending on an input, automatic adjustment function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or LCD monitors to change the resolution.

About Plug-and-Play capability

Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC 2B. Plug-and-Play can be achieved by connecting this projector to a computer is VESA DDC (display data channel) compatible.

• Please take advantage of this function by connecting the accessory RGB cable to the RGB IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

• Please use the standard drivers in your computer as this projector is a Plug-and-Play monitor.

to the

Setting up

Y R

AUDIO IN

AUDIO OU

CONTROL RGB IN

RGB IN

USB

RGB OU

AUDIO IN

VIDE

S-VIDEO

Y R

AUDIO IN

AUDIO OU

CONTROL RGB IN1

RGB IN2

USB

RGB OU

AUDIO IN1

VIDE

S-VIDEO

LAN

LINK

LAN

LINK

RGB IN2

Y R

AUDIO IN

AUDIO OUT

CONTROL RGB IN

RGB IN2

USB

RGB OU

AUDIO IN

VIDE

S-VIDEO

CR/PR

Y R

AUDIO IN

AUDIO OUT

CONTROL RGB IN

RGB IN

USB

RGB OU

AUDIO IN

VIDE

S-VIDEO

CB/P

CR/PR

Y R

AUDIO IN

AUDIO OUT

CONTROL RGB IN

RGB IN2

USB

RGB OU

AUDIO IN

VIDE

S-VIDEO

CB/P

CR/P

Y R

AUDIO IN

AUDIO OUT

CONTROL RGB IN

RGB IN

USB

RGB OU

AUDIO IN

VIDE

S-VIDEO

CB/PB

CR/PR

LAN

LINK

LAN

LINK

LAN

LINK

ACT

LAN

LINK

Examples of connection with a computer

* In the default setting, the AUDIO IN1 port is the audio port for the RGB IN1 and RGB IN2 ports. To change the settings, refer to the AUDIO item in the SETUP menu.

RGB cable

USB cable

RGB out

Stereo mini

Audio out RS-232C

USB

RS-232C cable

audio cable

RGB out

Audio out

Stereo mini audio cable

(34)

Use the RGB IN OUT switch to select RGB IN2 (RGB IN2 is selected if the switch is not pushed in).

RGB cable

RGB out

LAN

CAUTION ►For safety, do not connect LAN port to any network that might

have the excessive voltage.

LAN cable (CAT-5 cable)

RGB cable

Setting up

Y R

AUDIO IN

AUDIO OUT

CONTROL RGB IN

RGB IN

USB

RGB OU

AUDIO IN

VIDE

S-VIDEO

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN

RGB IN2

USB

RGB OU

AUDIO IN

VIDE

S-VIDEO

CB/P

CR/PR

Y R

AUDIO IN

AUDIO OUT

CONTROL RGB IN

RGB IN2

USB

RGB OU

AUDIO IN

VIDE

S-VIDEO

CB/P

CR/P

LAN

LINK

LAN

LINK

LAN

LINK

ACT

Y R

AUDIO IN

AUDIO OU

CONTROL RGB IN

RGB IN

USB

RGB OUT

AUDIO IN

VIDE

S-VIDEO

Y R

AUDIO IN

AUDIO OU

CONTROL RGB IN1

RGB IN2

USB

RGB OU

AUDIO IN1

VIDE

S-VIDEO

Y R

AUDIO IN

AUDIO OU

CONTROL RGB IN

RGB IN

USB

RGB OU

AUDIO IN

VIDE

S-VIDEO

Y R

AUDIO IN

AUDIO OU

CONTROL RGB IN

RGB IN

USB

RGB OU

AUDIO IN1

VIDE

S-VIDEO

LAN

LINK

LAN

LINK

LAN

LINK

LAN

LINK

RGB IN2

RGB OUT

Connecting to a monitor (output)

Use the RGB IN OUT switch to select RGB OUT (RGB OUT is selected if the

switch

is pushed in).

RGB in

RGB cable

Connecting to a speaker with ampliﬁer (output)

Audio in

Stereo mini audio cable

Examples of connection with a VCR/DVD player

* In the default setting, the AUDIO IN2 L/R port is the audio port for the VIDEO, S-VIDEO and COMPONENT VIDEO ports. To change the settings, refer to the AUDIO item in the SETUP menu.

Audio/Video cable

Audio (R) out

Audio (L) out

Video out

Audio cable

(34)

Audio (R) out

Audio (L) out

S-Video out

Component video out

CB/P

CR/P

Audio (R) out

Audio (L) out

S-Video cable

Component video cable

Audio cable

Setting up

Connecting power supply

WARNING ►Please use extra caution when connecting the power cord, as

incorrect or faulty connections may result in ﬁre and/or electrical shock.

• Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one.

• Only plug the power cord into an outlet rated for use with the power cord's speciﬁed voltage range.

• Never modify the power cord. Never attempt to defeat the ground connection of the three-pronged plug.

AC inlet

Connector of the power cord

Connect the connector of the power cord to the AC inlet of the projector.

Firmly plug the power cord's plug into the outlet.

Remote control

Putting batteries

WARNING ►Always handle the batteries with care and use them only as

directed. Battery may explode if mistreated. Do not recharge, disassemble or dispose of in ﬁre. And also improper use may result in cracking or leakage, which could result in ﬁre, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries speciﬁed. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

• Do not short circuit or solder a battery. Do not allow a battery in a ﬁre or water. Keep batteries in a dark, cool and dry place.

•

If you observe a leakage of a battery, wipe out the ﬂower and then replace a battery.

If the liquid adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

Remove the battery cover.

Slide back and remove the battery cover in the direction of the arrow.

nsert the batteries.

Align and insert the two AA batteries according to their plus and minus terminals as indicated in the remote control.

Close the battery cover.

Replace the battery cover in the direction of the arrow and snap it back into place.

Remote control

Using the remote control

CAUTION ►Be careful in handling the remote control.

• Do not drop or expose the remote control to physical impact.

• Do not get the remote control wet or place it on wet objects. It may result in malfunction.

• Remove the batteries from the remote control and store them in a safe place if you won’t be using the remote control for an extended period.

• Replace the batteries whenever the remote control starts malfunctioning.

• When strong lights (such as direct sunlight) or light from an extremely close range (such as from an inverter ﬂuorescent lamp), hit the projector’s remote sensor, the remote control may cause to function. Adjust the direction of the projector to keep the light from directly hitting the projector’s remote sensor.

The remote control works with the projector’s remote sensor.

30º

approx. 3 meters

• The range of the remote sensor is 3 meters with a 60 degree range (30 degrees to the left and right of the remote sensor).

• Also a remote signal reﬂected in the screen etc. may be available. If it is difﬁcult to send a remote signal to the sensor directly, please try to use the reﬂected signal.

• Since the remote control uses infrared light to send signals to the projector (Class1 LED), be sure to use the remote control in an area free from obstacles that could block the remote control’s output signal to the projector.

Power on/off

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARC

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

Power on/off

WARNING ►When the power is on, a strong light is emitted. Do not look into

the lens of projector. Also do not peep at the inside of projector through a hole.

NOTE •

Turn the power on/off in right order. Please power on the projector prior

to the connected devices. Power off the projector later than the connected devices.

Turning on the power

Make sure that the power cord is ﬁrmly and

correctly connected to the projector and the

STANDBY/ON button

outlet.

Remove the lens cover, and set the power

switch to the ON position. The power indicator will light up in steady orange. Then wait several seconds because the buttons may not function for these several seconds.

Press the STANDBY/ON button on the projector or the remote control.

The projector lamp will light up and the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in green.

To display the picture, select an input signal according to the section "Selecting an input signal"

(18)

Turning off the power

This product is able to turn off the main power during the cooling. However, please pay special attention to below two points when you do:

(1) Please do not turn the projector on again for at least 1 minute in this case.

Neglect could shorten the lifetime of the lamp.

(2) During use or immediately after use, do not touch around the lamp and vents

of the projector

Press the STANDBY/ON button on the projector or the remote control.

The message "Power off?" will appear on the screen for approximately 5 seconds.

Press the STANDBY/ON button on the projector or the

remote control again while the message appears. The projector lamp will go off, and the POWER indicator will begin blinking in orange.

Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

Make sure that the power indicator lights in steady orange,

and set the power switch to the OFF position. The POWER

indicator will go off. Attach the lens cover.

(4 )

It could cause a burn.

POWER indicator

POWER

(Steady orange)

POWER

(Blinking in green)

POWER

(Steady green)

Power off?

POWER

(Blinking in orange)

POWER

(Steady orange)

Operating

HOME

PAGE UP

PAGE DOWN

VIDEO

SEARC

MAGNIFY

ASPECT AUTO

BLAN

MUTE

VOLUME

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARC

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

MUTE

VOLUME

KEYSTONE

VIDEO

SEARC

ASPECT AUTO

BLAN

Operating

Adjusting the volume

Press the VOLUME button on the remote control.

A dialog will appear on the screen to aid you in adjusting the volume.

Use the cursor buttons ▲/▼ to adjust the volume.

To close the dialog and complete the operation, press the VOLUME button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds.

Temporarily muting the sound

Press the MUTE button on the remote control.

A dialog will appear on the screen indicating that you have muted the sound. To restore the sound, press the MUTE or VOLUME button.

Even if you don’t do anything, the dialog will automatically disappear after a few seconds.

Selecting an input signal

Press the INPUT button on the projector.

Each time you press the button, the projector switches its input port as below.

RGB IN1  RGB IN2 VIDEO  S-VIDEO  COMPONENT VIDEO

● When the RGB IN2/RGB OUT port functions as an RGB out port (the RGB IN OUT switch is pushed in), RGB IN2 cannot be selected. In that case “RGB2/RGB OUT displayed.

Press the RGB button on the remote control to select an

input port for the RGB signal. Each time you press the button, the projector switches its RGB input port as below.

RGB IN1  RGB IN2

RGB OUT” message will be



● If the RGB button is pushed (when switching from VIDEO to RGB signals) when TURN ON is selected for the AUTO SEARCH item in the OPTION menu the projector will check the RGB IN1 port ﬁrst. If no input is detected at the port, the projector will check the RGB IN2 port.

● When the RGB IN2/RGB OUT port functions as an RGB out port (the RGB IN OUT switch is pushed in), RGB IN2 cannot be selected. In that case “RGB2/ RGB OUT

RGB OUT” message will be displayed.



Operating

HOME

PAGE UP

VIDEO

SEARC

MAGNIFY

ASPECT AUTO

BLAN

VOLUME

VIDEO

SEARC

ASPECT AUTO

BLAN

VIDEO

SEARC

ASPECT AUTO

BLAN

Selecting an input signal (continued)

Press the VIDEO button on the remote control to select an

input for video signal. Each time you press the button, the projector switches its video input port as below.

COMPONENT VIDEO

S-VIDEO



VIDEO



● If the VIDEO button is pushed (when switching from RGB to VIDEO signals) when TURN ON is selected for the AUTO SEARCH item in the OPTION menu the projector will check the COMPONENT VIDEO port ﬁrst. If no input is detected at the port, projector will begin to check other ports in above order.

Searching an input signal

Press the SEARCH button on the remote control.

The projector will start to check its input ports in order to ﬁnd any input signals. Then when an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation.

RGB IN 1  RGB IN 2

COMPONENT VIDEO



S-VIDEO  VIDEO



Selecting an aspect ratio

Press the ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

For an RGB signal



NORMAL

4:3  16:9



For a video signal/no signal



4:3  16:9  SMALL

● The NORMAL mode keeps the original aspect ratio of the signal.

● For an HDTV signal of 1125i (1080i) or 750p (720p) as the COMPONENT VIDEO input, only 16:9 mode can be selected.

● Performing the automatic adjustment initializes the aspect ratio setting.

Adjusting the zoom and focus

Use the zoom ring to adjust the screen size.

Use the focus ring to focus the picture.

Focus ring

Zoom ring

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARC

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

MUTE

VOLUME

KEYSTONE

POSITION

HOME

PAGE UP

VIDEO

SEARC

MAGNIFY

ASPECT AUTO

BLAN

VOLUME

Using the automatic adjustment feature

Press the AUTO button on the remote control.

For an RGB signal



The vertical position, the horizontal position, the clock phase and the horizontal size will be automatically adjusted. And the aspect ratio will be automatically selected. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

For a video signal or s-video signal



The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO mode is selected to the VIDEO FORMAT item in the INPUT menu signal, the signal type is identiﬁed automatically independently of this function.

For a video signal, s-video signal or component video signal



The vertical position and horizontal position will be automatically adjusted.

For a component video signal



The aspect ratio will be automatically selected. The clock phase will be automatically adjusted.

● The automatic adjustment operation requires approximately 10 seconds. Also

please note that it may not function correctly with some input.

(32)

. For a component video

Adjusting the position

Press the POSITION button on the remote control.

The “POSITION” indication will appear on the screen. Use the cursor buttons ▲/▼/◄/► to adjust the picture

position.

When you want to reset the operation, press the RESET button on the remote control during the operation.

To complete this operation, press the POSITION button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds.

● When this function is performed at a video signal, a certain extra such as a line may appear outside a picture.

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARC

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

MUTE

VOLUME

KEYSTONE

HOME

PAGE UP

VIDEO

SEARC

MAGNIFY

ASPECT AUTO

BLAN

VOLUME

Correcting the keystone distortions

Press the KEYSTONE button on the remote control. A

dialog will appear on the screen to aid you in correcting the

distortion.

Use the cursor buttons ▲/▼ to correct the distortion.

To close the dialog and complete this operation, press the KEYSTONE button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds.

● The adjustable range for correction will vary among inputs. For some input, this function may not work well.

● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, this function may not work correctly.

● When the zoom adjustment is set to the TELE (telephoto focus), this correction may be excessive. This function should be used when the zoom adjustment is set to the WIDE (wide-angle focus) whenever possible.

Using the magnify feature

Press the ON button of MAGNIFY on the remote control.

The “MAGNIFY” indication will appear on the screen (although the indication will disappear in several seconds with no operation), and the projector will enter the MAGNIFY mode.

Use the cursor buttons ▲/▼ to adjust the zoom level.

To move the zoom area, press the POSITION button in the MAGNIFY mode, then use the cursor buttons ▲/▼/◄/► to move the area. And to ﬁnalize the zoom area, press the POSITION button again.

To exit the MAGNIFY mode and restore the screen to normal, press the OFF button of MAGNIFY on the remote control.

● The projector automatically exits the MAGNIFY mode when the input signal is changed, or when the display condition is changed.

● Although in the MAGNIFY mode, the keystone distortion condition may vary, it will be restored when the projector exits the MAGNIFY mode.

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARC

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

MUTE

VOLUME

KEYSTONE

HOME

PAGE UP

VIDEO

SEARC

MAGNIFY

ASPECT AUTO

BLANK

VOLUME

Freezing the screen

Press the FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen, and the

projector will enter the FREEZE mode. To exit the FREEZE mode and restore the screen to normal,

press the FREEZE button again.

● The projector automatically exits the FREEZE mode when the input signal changes, or when one of the projector’s buttons or the remote control buttons of STANDBY/ON, SEARCH, RGB, VIDEO, BLANK, AUTO, ASPECT, VOLUME, MUTE, KEYSTONE, POSITION and MENU is pressed.

● If the projector continues projecting a still image for long time, the LCD panel might possibly be printed. Do not leave the projector in the FREEZE mode for too long.

Temporarily blanking the screen

Press the BLANK button on the remote control.

The blank screen will be displayed instead of the screen of

input signal. Please refer to the BLANK item in the SCREEN

(35).

menu To exit the blank screen and return to the input signal screen, press the

BLANK button again.

● The projector automatically returns to the input signal screen when the input signal is changed, or when one of the projector’s buttons or the remote control buttons is pressed.

Operating

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARC

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

Operating the computer screen

CAUTION ►Mistaken use of the mouse/keyboard control could damage

your equipment.

• While using this function, please connect only with a computer.

• Before connecting, read the manuals of the computer you will connect.

NOTE • It may not be possible to control notebook PC, and other computers with built-in pointing device (e.g. track ball), using this remote control. In this case, before connecting go into BIOS (system setup) and select external mouse, and disable the pointing device. In addition, the mouse may not function if the computer does not have the needed utility program. See your computer’s hardware manual for details.

• The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to use the remote control, depending on the computer’s conﬁgurations and mouse drivers.

• The USB control can be used only for the functions listed below. You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

• This function is not available while the lamp is warming up (the POWER indicator ﬂashes green), and while adjusting the volume and display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu screen.

USB mouse and keyboard control

Connect the projector’s USB port to the computer via the mouse cable.

Available function Remote control operation

Move pointer Use ▲, ▼, ◄, ► buttons

Left click with mouse Press ENTER button

Right click with mouse Press RESET button

Press keyboard’s HOME key

Press keyboard’s END key

Press HOME button

Press END button

Press keyboard’s PAGE UP key Press PAGE UP button

Press keyboard’s PAGE DOWN key

Press keyboard’s ESC key

Press PAGE DOWN button

Press ESC button

Multifunctional settings

EASY MENU

ASPECT 4:3

Go To Advance Menu...

NORMAL

BRIGHT NORMAL

0h ENGLISH

KEYSTONE MODE BRIGHTNESS CONTRAST COLOR TINT SHARPNESS WHISPER MIRROR RESET FILTER TIME LANGUAGE

MENU [RGB]

IMAGE

SETUP

PICTURE

INPUT

OPTION

SCREEN

SHARPNESS 3

BRIGHTNESS ＋0 CONTRAST ＋0

COLOR +0 TINT +0

COLOR TEMP MIDDLE

GAMMA DEFAULT 1

MY MEMORY SAVE 1

:SELECT

NETWORK EASY MENU

PROGRESSIVE TURN OFF

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARC

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARC

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

Using the menu function

This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN, OPTION, NETWORK and EASY MENU. EASY MENU cosists of functions often used, and the other menus are classiﬁed into each purpose. Each of these menus is operated using the same methods. The basic operations of these menus are as follows.

In the EASY MENU

In the Advanced MENU

●

● Some functions cannot be performed when a certain input port is selected, or

Multifunctional settings

MENU button

ENTER button

Cursor buttons

RESET button

Press the MENU button on the remote control or one of the cursor buttons on the projector.

The Advanced MENU or EASY MENU will appear.

If you want to change it to the Advanced MENU, select the "Go to Advanced Menu"

Use the cursor buttons ▲/▼ to select an item to operate.

Use the cursor buttons◄/► to operate the item.

Use the cursor buttons ▲/▼ to select a menu.

If you want to change it to the EASY MENU, select the EASY MENU. Then press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to select an item. The display of the selected menu will be active.

Use the cursor buttons ▲/▼ to select an item to operate.

Then press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. The operation menu of the selected item will appear.

Use the cursor buttons▲/▼ to operate the item.

When you want to reset the operation, press the RESET button on the remote control during the operation. Note that items whose functions are performed simultaneously with operation (ex. LANGUAGE, H PHASE, VOLUME etc.) cannot be reset.

In the advanced menu, when you want to return to the previous display, press the cursor button ◄ on the projector or remote control, or the ESC button on the remote control.

Press the MENU button on the remote control again to close the menu

and complete this operation. Even if you don't do anything, the dialog will automatically disappear after about 10 seconds.

when a certain input signal is displayed.

With the EASY MENU, items shown in the table below can

EASY MENU

ASPECT 4:3

Go To Advance Menu...

NORMAL

BRIGHT

NORMAL

ENGLISH

KEYSTONE MODE BRIGHTNESS CONTRAST COLOR TINT SHARPNESS WHISPER MIRROR RESET FILTER TIME LANGUAGE

be performed. Select an item using the cursor buttons ▲/▼ on the

projector or remote control. Then perform it referring to the following table.

KEYSTONE

BRIGHTNESS

CONTRAST

SHRPNESS

WHISPER

EASY Menu

Item Description

ASPECT

MODE

COLOR

TINT

Using the buttons ◄/► switches the mode for aspect ratio. See the ASPECT item in the IMAGE menu

Using the buttons ◄/► corrects the keystone distortion. See the item KEYSTONE of section SETUP menu. (21)

Using the buttons ◄/► switches the mode of picture type. The modes of picture type are combinations of a mode of GAMMA and a mode of COLOR TEMP

. Choose a suitable mode according to the

projected source.

NORMAL

CINEMA



DYNAMIC



NORMAL: (COLOR TEMP = MIDDLE) + (GAMMA = #1 DEFAULT) CINEMA: (COLOR TEMP = LOW) + (GAMMA = #2 DEFAULT) DYNAMIC: (COLOR TEMP = HIGH) + (GAMMA = #3 DEFAULT)

• When the combination of GAMMA and COLOR TEMP differs from pre-assigned modes above, the display on the menu for the MODE is “CUSTOM”. Please refer to the GAMMA ( TEMP (

•

When this function is performed, a certain extra such as a line may appear.

28) items in the PICTURE menu.



Using the buttons ◄/► adjusts the brightness. See the item BRIGHTNESS in the PICTURE menu (27).

Using the buttons ◄/► adjusts the contrast. See the item CONTRAST of section PICTURE menu (27).

Using the buttons ◄/► adjusts the strength of whole color. See the COLOR item in the PICTURE menu (28).

Using the buttons ◄/► adjusts the tint. See the TINT item in the PICTURE menu (28).

Using the buttons ◄/► adjusts the sharpness. See the SHARPNESS item in the PICTURE menu (28).

• There may be some noise when an adjustment is made. This is not a malfunction.

Using the buttons ◄/► turns off/on the whisper mode. See the WHISPER item in the SETUP menu (34).

Multifunctional settings

(30).

27) and COLOR



Multifunctional settings

EASY Menu (continued)

Item Description

MIRROR

RESET

FILTER TIME

LANGUAGE

Go To

Advanced Menu

Using the buttons ◄/► switches the mode for mirror status. See the MIRROR item in the SETUP menu (34).

Performing this item resets all of the items of EASY MENU except FILTER TIME and LANGUAGE. A dialog is displayed for conﬁrmation. Selecting RESET using the button ▲ performs resetting.

Performing this item resets the ﬁlter timer which counts usage time of the air ﬁlter. A dialog is displayed for conﬁrmation. Selecting RESET using the button ▲ performs resetting. See the FILTER TIME item in the OPTION menu (38).

Select the LANGUAGE item to toggle the menu language. Refer to description of LANGUAGE in the SCREEN menu (35).

Select “Go To Advanced Menu” to use the IMAGE, INPUT, SETUP, SCREEN

menu of PICTURE,

or OPTION.

Multifunctional settings

GAMMA [CUSTOM 1

]

ENTER :

MENU [RGB]

IMAGE

SETUP

PICTURE

INPUT

OPTION

SCREEN

SHARPNESS 3

BRIGHTNESS ＋0 CONTRAST ＋0

COLOR +0 TINT +0

COLOR TEMP MIDDLE

GAMMA DEFAULT 1

MY MEMORY SAVE 1

:SELECT

NETWORK EASY MENU

PROGRESSIVE TURN OFF

PICTURE Menu

With the PICTURE menu, the items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item. Then perform it referring to the following table.

Item Description

BRIGHTNESS Using the buttons ▲/▼ adjusts the brightness. : Light  Dark

CONTRAST Using the buttons ▲/▼ adjusts the contrast. : Strong

Using the buttons ▲/▼ switches the GAMMA mode.

#1 DEFAULT

#1 CUSTOM  #2 DEFAULT



Weak

GAMMA

#3 CUSTOM

 #3 DEFAULT  #2 CUSTOM

To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM

Selecting a mode of CUSTOM and then pressing the button ► or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of particular tones.

Choose an item using the buttons ◄/►, and adjust the level using the buttons ▲/▼.

You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.

No pattern  Gray scale of 9 steps Ramp  Gray scale of 15 steps The eight equalizing bars correspond to eight tone levels of the

test pattern except the darkest in the left end. If you want to adjust the 2nd tone from left end on the test pattern, use the equalizing adjustment bar “1”. The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar.

• When this function is performed, a certain extra such as a line may appear.

Multifunctional settings

COLOR TEMP

ENTER :

OFFSET

GAIN

PICTURE Menu (continued)

Item Description

Using the buttons ▲/▼ switches the mode of color temperature.

HIGH  MIDDLE  LOW

To adjust CUSTOM

Selecting the CUSTOM and then pressing the button ► or the ENTER button displays a dialog to aid you in adjusting the OFFSET and/or GAIN of the CUSTOM mode.

OFFSET adjustments change the color intensity on the whole tones of the test pattern.

COLOR TEMP

COLOR

TINT

SHARPNESS

GAIN adjustments mainly affect color intensity on the brighter tones of the test pattern.

Choose an item using the buttons ◄/►, and adjust the level using the buttons ▲/▼.

You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.

No pattern  Gray scale of 9 steps Ramp  Gray scale of 15 steps

• When this function is performed, a certain extra such as a line may appear.

Using the buttons ▲/▼ adjusts the strength of whole color.

Strong

• This item can be selected only for a video signal. Using the buttons ▲/▼ adjusts the tint.

Green  Red

• This item can be selected only for a video signal except for SECAM.

Using the buttons ▲/▼ adjusts the sharpness.

Strong

• There may be some noise and/or the screen may ﬂicker for a moment when an adjustment is made. This is not a malfunction.



Weak

CUSTOM



PICTURE Menu (continued)

Item Description

Using the buttons ▲/▼ switches the progress mode.

TV  FILM

• This function is performed only for an interlaced signal of a VIDEO input, an S-VIDEO input or CONPONENT VODEO input of 525i

PROGRESSIVE

(480i) or 625i (576i) signal.

• When TV or FILM is selected, the screen image will be sharp. FILM adapts to the 2-3 Pull-Down conversion system. But these may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select TURN OFF, even though the screen image may lose the sharpness.

Selecting a mode of MY MEMORY using the buttons ▲/▼ and then pressing the button ► or the ENTER button performs each function.

Multifunctional settings

TURN OFF



LOAD1  LOAD2  LOAD3  LOAD4

MY MEMORY

SAVE4

This projector has 4 numbered memories for adjustment data. Performing the LOAD1, LOAD2, LOAD3 or LOAD4 loads the data on the memory whose number corresponds to the command’s number, and adjusts the picture automatically depending on the data. Performing the SAVE1, SAVE2, SAVE3 or SAVE4 saves the current adjustment data on the memory whose number corresponds to the command’s number.

• The current adjustment data of the items in the PICTURE menu is stored, except for the adjustment data in the CUSTOM modes for the GAMMA and COLOR TEMP items.

• There may be some noise and/or the screen may ﬂicker for a moment when data is loaded to memory. This is not a malfunction.

SAVE3  SAVE2  SAVE1



MENU [RGB]

IMAGE

PICTURE

:SELECT

AUTO ADJUST EXECUTE

ASPECT 4:3 OVER SCAN 5

H PHASE 16 H SIZE 1344

H POSITION 142

V POSITION 25

SETUP

INPUT

OPTION NETWORK EASY MENU

SCREEN

Multifunctional settings

IMAGE Menu

With the IMAGE menu, items shown in the table below can be performed.

Item Description

Using the buttons ▲/▼ switches the mode for aspect ratio. For an RGB signal

4:3  16:9  NORMAL

ASPECT

OVER SCAN

V POSITION

H POSITION

H PHASE

For a video signal / no signal

4:3  16:9  SMALL

• The NORMAL mode keeps the original aspect ratio of the signal.

• For an HDTV signal of 1125i (1080i) or 750p (720p) as the COMPONENT VID

EO input, this item can't be selected.

Using the buttons ▲/▼ adjusts the over-scan ratio.

Large (It reduces picture)

Small (It magniﬁes picture)



• This item can be selected only for a video signal.

• When this adjustment is too large, certain degradation may appear at the frame area of the picture. In such a case, please adjust small.

Using the buttons ▲/▼ adjusts the vertical position.

Up  Down

• Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs please reset the vertical position to the default setting. Pressing the RESET button when V POSITION is selected will reset the V POSITION to the default setting.

Using the buttons ▲/▼ adjusts the horizontal position.

Left  Right

• Over-adjusting the horizontal position may cause noise to appear on the screen. If this occurs please reset the horizontal position to the default setting. Pressing the RESET button when H POSITION is selected will reset the H POSITION to the default setting.

Using the buttons ▲/▼ adjusts the horizontal phase to eliminate ﬂicker.

Right  Left

• This item can be selected only for an RGB signal or a component video signal. Note that this does not work with the input signal of 525i(480i)/625i(576i)/SCART RGB from the

component video port.

IMAGE Menu (continued)

Item Description

Using the buttons ▲/▼ adjusts the horizontal size.

Large  Small

H SIZE

AUTO ADJUST

EXECUTE

• This item can be selected only for an RGB signal.

• When this adjustment is excessive, the picture may not be displayed correctly. In such a case, please reset the adjustment by pressing the RESET button on the remote control during this operation.

Selecting this item performs the automatic adjustment feature.

For an RGB signal

For a video signal or s-video signal

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO mode is selected to the VIDEO FORMAT item in the INPUT menu. For a component video signal, the signal type is identiﬁed automatically independently of this function.

For a video signal, s-video signal or component video signal

The vertical position and horizontal position will be automatically adjusted.

For a component video signal

The aspect ratio will be automatically selected. The clock phase will be automatically adjusted.

• The automatic adjustment operation requires approximately 10 seconds. Also please note that it may not function correctly with some input.

Multifunctional settings

MENU [RGB]

IMAGE

SETUP

PICTURE

INPUT

OPTION NETWORK EASY MENU

SCREEN

:SELECT

VIDEO FORMAT AUTO

COLOR SPACE AUTO

FRAME LOCK INFORMATION

COMPONENT COMPONENT

TURN ON

Multifunctional settings

INPUT Menu

With the INPUT menu, the items shown in the table below can be performed.

Item Description

Using the buttons ▲/▼ switches the mode for color space.

COLOR SPACE

COMPONENT

VIDEO FORMAT

FRAME LOCK

AUTO

• This item can be selected only for an RGB signal or a component video signal (except signals of 525i(480i)/625i(576i)/SCART RGB from the component video port).

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well at some signals. In such a case, it might be good to select a suitable mode except AUTO.

Using the buttons ▲/▼ switches the function of COMPONENT VIDEO port.

COMPONENT

When the SCART RGB is selected, the COMPONENT VIDEO port function as a port for a SCART RGB signal input. A SCART adapter and SCART cable realize a SCART RGB input to the projector. For details, contact your dealer.

Using the buttons ▲/▼ switches the mode for video format.

AUTO  NTSC N-PAL  M-PAL  NTSC4.43

• This item is performed only for a video signal from the VIDEO port or the S-VIDEO port. For a component video signal, the signal type is identiﬁed automatically independently of this function.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well for some signals. If the picture becomes unstable (ex. an irregular picture, a color lack), please select the mode depending on the input signal.

Using the buttons ▲/▼ turns the frame lock function on/off.

TURN ON  TURN OFF

• This item performs only at a RGB signal with vertical frequency of 50 to 60 Hz.

• When the TURN ON is selected, a moving picture is displayed more smoothly.

• This function may cause a certain degradation of the picture. In such a case, please select the TURN OFF.

RGB  SMPTE240  REC709  REC601



SCART RGB



PAL

SECAM



INPUT Menu (continued)

INPUT-INFORMATION

RGB

1024x768 @60.0

FRAME LOCK

INPUT-INFORMATION

S-VIDEO

SECAM

AUTO

INPUT-INFORMATION

COMPONENT

576i @50

SCART RGB

Item Description

Selecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.

Multifunctional settings

INFORMATION

• The “FRAME LOCK” message on the dialog means the frame lock function is working.

• The “SCART RGB” message means the COMPONENT VIDEO port is working as a SCART RGB COMPONENT item in this menu.

input port. Please refer to the (32)

• This item can't be selected for no signal and sync out.

Multifunctional settings

MENU [RGB]

IMAGE

SETUP

PICTURE

INPUT

OPTION NETWORK EASY MENU

SCREEN

:SELECT

WHISPER BRIGHT MIRROR NORMAL

KEYSTONE +0

AUDIO

VOLUME 16

AUDIO

RGB2

QUIT

RGB1

S‑VIDEO

VIDEO

COMPONENT

1 2

SETUP Menu

With the SETUP menu, the items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item. Then perform it referring to the following table.

Item Description

Using the buttons ▲/▼ corrects the keystone distortion.

Upper in the data  Lower in the data

• The adjustable range of this function will vary with the type of input signal. At some signals, this function may not work well.

KEYSTONE

WHISPER

• When the V:INVERT or the H&V:INVERT is selected under the item MIRROR, if the projector screen is inclined or if the projector is angled downward, this function may not work correctly.

• When the zoom adjustment is set to the TELE side, this correction may be excessive. This function should be used with zoom set to WIDE whenever possible.

Using the buttons ▲/▼ turns off/on the whisper mode.

BRIGHT  NORMAL

• When the NORMAL is selected, acoustic noise and screen brightness are reduced.

Using the buttons ▲/▼ switches the mode for mirror status.

MIRROR

VOLUME

AUDIO

NORMAL

H:INVERT  V:INVERT  H&V:INVERT



Using the buttons ▲/▼ adjusts the volume.

High  Low

Choose an input port using the buttons ▲/▼ (1), then select the audio port to be interlocked with the input port using the buttons ◄/► (2). When off is selected, both of two audio ports do not work for the input port.

(1) RGB1  RGB2

COMPONENT



S-VIDEO  VIDEO



(2) 1  2 

Multifunctional settings

SUOMI  POLSKI  TÜRKÇE

ENGLISH  FRANÇAIS  DEUTSCH  ESPAÑOL  ITALIANO

NORSK  NEDERLANDS  PORTUGUÊS  日本語

   SVENSKA 

MENU [RGB]

IMAGE

SETUP

PICTURE

INPUT

OPTION NETWORK

EASY MENU

SCREEN

:SELECT

LANGUAGE ENGLISH MENU POSITION

START UP ORIGINAL

OSD BRIGHT. 5

MyScreen MyScreen Lock TURN OFF MESSAGE TURN ON

BLANK BLACK

SCREEN Menu

With the SCREEN menu, the items shown in the table below can be performed.

Item Description

Using the buttons ▲/▼ switches the OSD (On Screen Display) language.

LANGUAGE

Using the buttons ◄/►/▲/▼ adjusts the menu position.

MENU POSITION

OSD BRIGHT.

BLANK

To quit the operation, press the MENU button on the remote control or keep no operation for 10 seconds.

Using the buttons ▲/▼ switches the brightness level of the OSD (On Screen Display).

BRIGHT

DARK



Using the buttons ▲/▼ switches the mode for the blank screen. The blank screen is a screen for the temporarily blanking feature (22). It is displayed by pressing the BLANK button on the remote control.

MyScreen

ORIGINAL



BLUE  WHITE  BLACK



MyScreen is a screen you can register as a desired screen. The ORIGINAL screen is the existing standard screen. and BLACK are non-patterned (plain) screens in each color.

• To avoid remaining as an afterimage, the MyScreen and the ORIGINAL screens will change to the BLACK screen after several minutes.

• For the MyScreen, please refer to the MyScreen item (36).

BLUE, WHITE

Multifunctional settings

SCREEN Menu (continued)

Item Description

Using the buttons ▲/▼ switches the mode for the start-up screen. The start-up screen is a screen displayed when no signal or an unsuitable signal is detected.

MyScreen

MyScreen is a screen you can register as a desired screen.The

START UP

MyScreen

MyScreen Lock

ORIGINAL screen is the existing standard screen. When TURN OFF is selected, the BLACK screen is used.

• To avoid remaining as an afterimage, the MyScreen and the ORIGINAL screens will change to the BLANK screen after several minutes. If also the BLANK screen is the MyScreen or ORIGINAL, it will change to the BLACK screen.

• For the MyScreen, please refer to the item MyScreen the BLANK screen, please refer to the BLANK item (35).

This item functions for capturing the MyScreen of the blank screen and the start-up screen. Please execute displaying the input including the picture you want to capture.

1. Selecting this item displays a dialog titled “MyScreen”. It will ask you if you start capturing the picture from the current screen. Please wait for the target picture to be displayed, and press the ENTER button on the remote control when the picture is displayed. The picture will freeze and the frame for capturing appears.

To stop performing, press the RESET or ESC button on the

remote control.

2. Using the buttons ◄/►/▲/▼ adjusts the frame position. Please move the frame to the position of the picture which you want to use.

The frame may not be able to be moved for some input signals. To start registration, press the ENTER button on the remote

control.

To restore the screen and return to the previous dialog, press the

RESET or ESC button on the remote control.

Registration takes several minutes. When the registration is completed, the registered screen and the message “MyScreen registration is ﬁnished.” are displayed for several seconds. If the registration failed, the message “A capturing error has occurred. Please try again.” is displayed.

Using the buttons ▲/▼ turns on/off the MyScreen lock function.

TURN ON

When the TURN ON is selected, the item MyScreen is locked. Use this function for protecting the current MyScreen.

ORIGINAL  TURN OFF



TURN OFF



below

. For

SCREEN Menu (continued)

Item Description

Using the buttons ▲/▼ turns on/off the message function.

TURN ON

When the TURN ON is selected, the following message function works.

“AUTO IN PROGRESS” while automatically adjusting ”NO INPUT IS DETECTED”

MESSAGE

”SYNC IS OUT OF RANGE” "Searching….” while searching for the input ”Detecting….” while an input signal is detected The indication of the input signal displayed by changing The indication of the aspect ration displayed by changing The indication of "FREEZE" and "II" while freezing the screen by pressing the FREEZE button.

• When the TURN OFF is selected, please remember if the picture

is freezing. Do not mistake freezing for a malfurction (22).

TURN OFF



Multifunctional settings

AUTO OFF

ENABL

AUTO OFF

DISABLE

MENU [RGB]

PICTURE

:SELECT

IMAGE

SETUP

INPUT

OPTION NETWORK EASY MENU

SCREEN

AUTO OFF 0min LAMP TIME 0h FILTER TIME 0h

AUTO SEARCH TURN OFF

SERVICE

OPTION Menu

With the OPTION menu, the items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item, except for the items LAMP TIME and FILTER TIME. T

hen perform it referring to the following table.

Item Description

Using the buttons ▲/▼ turns on/off the automatic signal search function.

TURN ON

TURN OFF



This function works with INPUT, RGB, and VIDEO buttons. When the TURN ON is selected, detecting no signal automatically cycles through input ports in the following order. The search is

AUTO SEARCH

started from the current port. Then when an input is found, the projector will stop searching and display the image.

RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO

•

When the RGB IN2/RGB OUT port functions as an RGB out port (the RGB IN OUT switch is pushed in), RGB IN2 cannot be selected. In that case “RGB2/RGB OUT

Using the buttons ▲/▼ adjusts the time to count down to automatically turn the projector off.

Long (max. 99 minutes)  Short (min. 0 minute = DISABLE)

RGB OUT



message will be displayed.

”

LAMP TIME

FILTER TIME

AUTO OFF

When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with nosignal or an unsuitable signal reaches at the set time, the projector lamp will go off and the power indicator begins blinking. Please refer to the section “Turning off the power” (17).

The lamp time is the time counted after the last resetting. It is shown in the OPTION menu as the usage time of the lamp. Pressing the RESET button on the remote control or the button ► of the projector displays a dialog. To reset the lamp time, select the RESET using the button ▲.

RESET

CANCEL



• Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp.

• For the lamp replacement, see the section "Lamp" (43, 44). The ﬁlter time is the time counted after the last resetting. It is shown

in the OPTION menu as the usage time of the air ﬁlter. Pressing the RESET button on the remote control or the button ► of the projector displays a dialog. To reset the ﬁlter time, select the RESET using the button ▲.

RESET  CANCEL

•

Please reset the ﬁlter time only when you have cleaned or replaced the air ﬁlter, for a suitable indication about the air ﬁlter.

• For the air ﬁlter cleaning, see the section "Air ﬁlter" (45).

OPTION Menu (continued)

Item Description

Selecting this item displays the SERVICE menu. Select an item using the buttons ▲/▼, and press the button ► or the ENTER button on the remote control to execute the item.

FAN SPEED  AUTO ADJUST

FAN SPEED

Using the buttons ▲/▼ switches the rotation speed of the cooling fans. The HIGH is the mode for use at highlands etc. projector is noisier when the HIGH is selected.

HIGH  NORMAL

AUTO ADJUST

Using the buttons ▲/▼ enables/disables the automatic adjustment. When DISABLE is selected, the automatic adjustment feature is disabled, although rough adjustment is automatically performed depending on the basic setting.

ENABLE  DISABLE

•

Depending on conditions, such as input image, signal cable to the projector, environment around the projector, etc., the automatic adjustment may not work correctly. In such a case, please choose DISABLE to disable the automatic adjustment, and make adjustment manually.

GHOST

1. Select a color element of ghost using the buttons

Adjust the selected element using the buttons ▲/▼ to disappear ghost.

KEY LOCK

SERVICE

Using the buttons ▲/▼ turns on/off the key lock feature. When TURN ON is selected, the buttons on the projector except the STANDBY/ON button are locked.

TURN ON

• Please use to avoid a mischief and touching accidentally. This function does not have any effect on the remote control.

FILTER MESSAGE

Use the ▲/▼ button to set the timer for the interval to show the message for cleaning up the air ﬁlter.

50h  100h  200h  300h After selecting “50h”, “100h”, “200h”, or “300h”, the message “CLEAN THE AIR FILTER” will appear after the timer reaches the interval time set by the menu. (38) When the “TURN OFF” is chosen, the air ﬁlter cleaning message will not appear.

• Please check and clean the air ﬁlter periodically, even if there is no message. If the air ﬁlter becomes to be blocked by dust or others, the internal temperature will rise, which could cause malfunction, or reduce the lifetime of the projector.

• It is recommended to choose “100h” in general. Please be careful with the operating environment of the projector and the condition of the air ﬁlter, especially when the chosen.

FACTORY RESET

Selecting RESET using the button ▲ performs this function. By this function, all the items in all of menus will collectively return to the initial setting. Note that the items LAMP TIME, FILTER TIME and LANGUAGE are not reset.

RESET  CANCEL

TURN OFF



Multifunctional settings

 KEY LOCK  FILTER MESSAG  FACTORY RESET

GHOST



◄/►.

TURN OFF



“200h”, “300h or “TURN OFF” is

Note that the

MENU [RGB]

IMAGE

SETUP

PICTURE

INPUT

OPTION

EASY MENU

SCREEN

:SELECT

NETWORK

IP ADDRESS SUBNET MASK

DATE AND TIME

DHCP

TURN OFF

DEFAULT GATEWAY

TIME DIFFERENCE e‑SHOT

INFORMATION

Multifunctional settings

DHCP

TURN ON

TURN OFF

192. 168. 254

IP ADDRESS

255. 255. 0

SUBNET MASK

255.

NETWORK Menu

Select [Network] from the main menu to access the following functions.

NOTE • The factory default setting for DHCP is “TURN ON”. There is no need to set up [DHCP], [IP ADDRESS], [SUBNET MASK] or [DEFAULT GATEWAY] if your network has DHCP enabled.

• If you are not utilizing SNTP set the DATE AND TIME during the initial installation. Please refer to the item DATE AND TIME on the following list.

NOTE Consult with your network administrator before connecting to an existing access point on your network. Incorrect network settings on this projector may cause trouble on the network.

Item Operation

DHCP

(Dynamic Host

Conﬁguration

Protocol)

IP ADDRESS

SUBNET MASK

( User’s Manual - Network Functions)

( User’s Manual - Network Functions), then you must

DHCP TURN ON/TURN OFF: Use the ▲/▼ buttons to turn DHCP on/off

TURN ON

TURN OFF



Select TURN OFF when the network does not have DHCP enabled.

Entering the IP ADDRESS : Use the ▲/▼/◄/► buttons to enter the IP ADDRESS. This function can only be used when DHCP is set to “TURN OFF”.

~Note~

The IP ADDRESS is the number that identiﬁes this projector on the network. You cannot have two devices with the same IP ADDRESS on the same network.

Entering the SUBNET MASK : Use the buttons ▲/▼/◄/► to enter the same SUBNET MASK used by your PC. This function can only be used when DHCP is set to “TURN OFF”.

NETWORK Menu (continued)

0. 0. 0

DEFAULT GATEWAY

e‑SHOT

IMAGE‑2

IMAGE‑1

IMAGE‑3 IMAGE‑

e‑SHOT

RESET : IMAGE‑1

, + :NO , :YES

ESC

ENTER

TIME DIFFERENCE

GMT 00:00

IMAGE‑1

Item Operation

DEFAULT

GATEWAY

DATE AND TIME

TIME

DIFFERENCE

e-SHOT

Multifunctional settings

Entering the DEFAULT GATEWAY : Use the

▲/▼/◄/►

buttons to enter the DEFAULT GATEWAY (therouter or PC that forwardstrafﬁc to a destination outside of the subnet of the transmitting device) address.This function can only be used when DHCP is set to “TURN OFF”.

Entering DATE AND TIME : Use the ▲/▼/◄/► buttons to enter the Year (last two digits), Month, Date, Hour and Minute.

~Note~

The projector will override this setting and retrieve DATE AND TIME information from the Timeserver when SNTP is enabled. See

Time Settings]

in [User’s Manual - Network Functions: Conﬁguring

[Date/

and Controlling the Projector via a Web Browser] for SNTP settings.

Entering the TIME DIFFERENCE : Use the ◄/► buttons to enter the TIME DIFFERENCE. Set the same TIME DIFFERENCE as the one set on your PC. If unsure, consult your network administrator. Use the ▲ button to return to the menu after setting the TIME DIFFERENCE.

e-SHOT display : Use the ▲/▼ buttons to select an item and the ► or ENTER buttons to display the image.

Image1 Image2 Image3 Image4

Once an image is displayed, you can use the ▲/▼ buttons to page through the images. Use the ◄ or ESC buttons to return to the menu. Pressing the RESET button on the remote control while an image is being displayed will display the RESET menu. The displayed image can be deleted from the RESET menu using the ENTER button on the remote control or the INPUT button on the projector. If you do not wish to delete the image use the ESC button on the remote control or push the ◄ and INPUT buttons on the projector at the same time.

~Note~

•

Items with no image stored cannot be selected.

•

Images can be changed using the

▲/▼

buttons while the image data downloads.

Multifunctional settings

IP ADDRESS 192.168.1.254 SUBNETMASK 255.255.255.0

NETWORK‑INFORMATION

DEFAULT GATEWAY 0.0.0.0 MAC ADDRESS

NAME

DATE AND TIME 2000/1/1 TIME DIFFERENCE GMT 00:0

000 :87:56:AC:7C

NETWORK Menu (continued)

Item Operation

INFORMATION display : Use the ► or ENTER buttons to view network information and conﬁrm settings.

INFORMATION

~Note~

• Only the ﬁrst 16 characters of the projector name are displayed.

• The battery for the built in clock may be dead if the clock loses time even when the DATE AND TIME have been set correctly. Replace the battery by following the instructions on replacing the battery.

(47)

Network Functions

Refer to the separate volume on Network Functions.

Maintenance

Lamp

Maintenance

WARNING

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to ﬂy into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

►About disposal of a lamp • This product contains a mercury lamp; do not put it in a trash. Dispose of it in accordance with environmental laws. For lamp recycling, go to www.lamprecycle.org. (in the US) For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada). For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the inside of the projector, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

Disconnect

the plug from the

• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.

power

• Before replacing the lamp, turn the projector off and unplug the power

outlet

cord, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp cover while the projector is suspended from the ceiling. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. To replace the lamp, make sure that the screws are tightened firmly. Loose screws could result in damage or injury.

• Use only the lamp of the speciﬁed type.

• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

•

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

• Using the lamp for long periods of time, could cause it dark, not to light up or to burst. When the pictures appear dark, or when the color tone is poor, please replace the lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.

Maintenance

Lamp (continued)

A lamp has a ﬁnite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, contact your dealer and tell the lamp type number.

Type number = DT00731.

Turn the projector off, and unplug the power cord. Allow the lamp to cool for

at least 45 minutes. Prepare a new lamp.

If the projector is mounted on the ceiling, or if the lamp has broken, also ask

the dealer to replace the lamp.

In the case of replacement by yourself,

Loosen the lamp cover screw (marked by arrow)

and then slide the lamp cover to the side to

remove it.

Loosen the 2 screws (marked by arrow) of the

lamp, and slowly pick up the lamp by the handles.

Insert the new lamp, and retighten ﬁrmly the two

screws that are loosened in the previous process

to lock it in place.

Slide the lamp cover back in place and ﬁrmly

fasten the lamp cover a screw. Turn the projector on and reset the lamp time

using the LAMP TIME function in the OPTION

(38)

(1) Press the MENU button to display a menu. Only

when the EASY MENU has appeared, please perform the next step (2).

(2) Point at the “Go To Advance Menu …” in the menu

using ▼/▲ button, then press the ► button.

(3) Point at the “OPTION” in the left column of the

menu using ▼/▲ button, then press the ► button.

(4) Point at the ”LAMP TIME” using ▼/▲ button, then

press the ► button. A dialog will appear.

(5) Press the ▲ button to select “RESET” on the

dialog. It performs resetting the lamp time.

Screws

Lamp cover

Screw

Handle

NOTE • Please reset the lamp time only when you have replaced the lamp,

for a suitable indication about the lamp.

Maintenance

Air ﬁlter

WARNING ►Before caring, make sure the power switch is off and the

power cable is not plugged in, then allow the projector to cool sufﬁciently. The care in a high temperature state of the projector could cause an electric shock, a burn and/or malfunction to the projector. ►Use only the air ﬁlter of the speciﬁed type. Do not use the projector with the air ﬁlter and the ﬁlter cover removed. It could result in a ﬁre and/or malfunction to the projector. ►The air ﬁlter should be cleaned periodically. If the air ﬁlter becomes clogged by dust or the like, internal temperatures rise and could cause a ﬁre, a burn and/or malfunction to the projector.

NOTE • Please replace the air ﬁlter when it is damaged or too soiled, and

also when you replace the lamp.

• Please reset the ﬁlter time only when you have cleaned or replaced the air ﬁlter, for a suitable indication about the air ﬁlter.

• The projector may display the message such as “CHECK THE AIR FLOW” or turn off the projector, to prevent the internal heat level rising.

If the air ﬁlter becomes clogged by dust or the like, internal temperatures rise and could cause a ﬁre, a burn and/or malfunction to the projector. When the indicators or a message prompts you to clean the air filter, clean the air filter as soon as possible. Please check and clean the air filter periodically, even if there is no message. Please replace the air ﬁlter when it is damaged or too soiled. Preparation of a new air ﬁlter is recommended. To prepare a new air ﬁlter, contact your dealer and tell the air ﬁlter type number.

Type number =

And also when you replace the lamp, please replace the air ﬁlter. An air ﬁlter of speciﬁed type will come together with a replacement lamp for this projector.

Turn the projector off, and unplug the

power cord. Allow the lamp to cool for at

least 45 minutes.

When the projector is suspended from

the ceiling, apply the vacuum cleaner to and around the ﬁlter cover ﬁrst, to prevent penetration of dust or the like.

While supporting the projector with one

hand, use your other hand to pull the ﬁlter cover forward in the direction of the arrow. Remove the air ﬁlter.

NJ22222

(38)

Handle

Filter cover

Maintenance

Air ﬁltre (continued)

Apply a vacuum cleaner to the air ﬁlter

and the ﬁlter cover. Please replace the air ﬁlter when it is damaged or too soiled.

Replace the air ﬁlter in its original

position. Secure the air ﬁlter in place by pressing each of the six locations. Make sure there is no dust or dirt remaining after the cover is in place. If any dust or dirt remains use a vacuum cleaner to remove it as when placing the ﬁlter

(38)

cover on the air ﬁlter. Reattach the ﬁlter cover to the projector by aligning the ﬁlter cover with the grooves on the projector. While holding the handle, push down on the ﬁlter cover until it locks ﬁrmly in place.

Turn the projector on and reset the ﬁlter

time using the FILTER TIME function in the OPTION menu

(1) Press the MENU button to display a menu. When the EASY MENU has

appeared, please skip the next step (2).

(2) Point at the “OPTION” in the left column of the menu using ▼/▲ button, then

press the ► button.

(3) Point at the “FILTER TIME” using ▼/▲ button, then press the ► button. A

dialog will appear.

(4) Press the ▲ button to select “RESET” on the dialog. It performs resetting the

ﬁlter time.

Air ﬁlter’s knob

Air ﬁlter

mark

Filter cover

OPEN

Maintenance

Replacing Internal Clock battery

Consumption of the battery makes the clock not to work correctly. When the clock is wrong or it has stopped, please replace the battery according to the following procedures.

WARNING ► may explode if mistreated. Do not recharge, disassemble or dispose of in ﬁre. And also improper use may result in cracking or leakage, which could result in ﬁre, injury and/or pollution of the surrounding environment.

•

Be sure to use only the batteries speciﬁed. Do not use batteries of different types at the same

time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

If the battery is placed in the battery holder upside-down, it may be hard to remove.

•

Keep a battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

•

Do not short circuit or solder a battery.

•

Do not allow a battery in a ﬁre or water. Keep batteries in a dark, cool and dry place.

•

If you observe a leakage of a battery, wipe out the ﬂower and then replace a battery. If the liquid

adheres to your body or clothes, rinse well with water immediately.

•

Obey the local laws on disposing the battery.

Turn the projector off, and unplug the power cord. Allow the

projector to cool sufﬁciently. After making sure that the projector has cooled adequately,

slowly turn over the projector, so that the bottom is facing. Remove the battery cover.

Turn the battery cover in the direction indicated “OPEN” using such as coins. Then the battery cover will come up. While removing the battery cover, pick its knob.

Take the old battery out.

Press the metal claw of the battery holder. Then the battery will come up. Remove the battery.

Put a new battery in.

Replace battery with HITACHI MAXELL, Part No.CR2032 only. Use of another battery may present a risk of ﬁre or explosion.

Insert a new battery in the battery holder according to its minus terminal

as indicated in the battery holder, so that the side marked by + is

facing. And push the battery into the battery holder fully to ﬁx.

Close the battery cover.

Replace the battery cover in place, then turn it in the direction indicated “CLOSE” using such as coins, to ﬁx.

Always handle the batteries with care and use them only as directed. Battery

Battery Cover

Metal claw

Knob

“+” marking

If the battery is placed in the battery holder upside-down, follow the procedure below to remove and reload it properly.

1. Remove the battery cover as described in steps 1 through 3 above.

2. Turn the projector over again, so that the top of the projector is facing up.

3. While lifting the side of the projector closest to the lens, press the metal claw of the battery holder. The battery will fall out of the holder, so be careful not to lose it.

4. Turn the projector over once more, so that the bottom faces up, and reload the battery correctly.

NOTE •

Please reconﬁgure the time via the menu or a web browser after replacing the battery.

(Please refer to 41

The internal clock’s time will be reset when the battery is removed.

and User’s Manual-Network Functions: Date/Time Settings for more information.)

Maintenance

Other care

WARNING ►Before caring, make sure the power switch is off and the

power cable is not plugged in, and then allow the projector to cool sufﬁciently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector. ►Never try to care for the inside of the projector personally. Doing is so dangerous. ►Avoid wetting the projector or inserting liquids in the projector. It could result in a ﬁre, an electric shock, and/or malfunction to the projector.

• Do not put a container containing water, cleaner or chemicals near the projector.

• Do not use aerosols or sprays. CAUTION ►Please take right care of the projector according to the

following. Incorrect care could cause not only an injury but adverse inﬂuence such as discoloration, peeling paint, etc. ►Do not use cleaner or chemicals other than those listed below. ►Do not polish or wipe with hard objects.

Inside of the projector

In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year.

Caring for the lens

If the lens is ﬂawed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of handling.

Turn the projector off, and unplug the power cord. Allow the projector to cool

sufﬁciently. After making sure that the projector is cool adequately, lightly wipe the lens

with a commercially available lens-cleaning wipe. Do not touch the lens

directly with your hand.

Caring for the cabinet and remote control

Incorrect care could have adverse inﬂuence such as discoloration, peeling paint, etc.

Turn the projector off, and unplug the power cord. Allow the projector to cool

sufﬁciently. After making sure that the projector is cool adequately, lightly wipe with gauze

or a soft cloth. If soiling is severe, dip soft cloth in water or a neutral cleaner diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.

NO INPUT IS DETECTED

ON ***

SYNC IS OUT OF RANGE

ON *** fH *****kHz fV *****Hz

Troubleshooting

Related messages

When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please follow the instructions described below. If the same message is displayed after the remedy, or if a message other than the following appears, please contact your dealer or service company.

Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message Description

There is no input signal.

Please conﬁrm the signal input connection, and the status of the signal source.

The horizontal or vertical wavelength of the input signal is out of the response parameter range of this unit.

Please conﬁrm the specs for your projector or the signal source specs.

The internal temperature is rising.

Please turn the power off, and allow the projector to cool down at least 20 minutes. After having conﬁrmed the

CHECK THE AIR FLOW

REMINDER

*** HRS PASSED AFTER THE

LAST FILTER CHECK.

FILTER MAINTENANCE IS ESSENTIAL

TO REMOVE WARNING MESSAGE,

RESET FILTER TIMER.

SEE MANUAL FURTHER INFO.

following items, please turn the power ON again.

• Is there blockage of the air passage aperture?

• Is the air ﬁlter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the remedy, please set FAN SPEED of the SERVICE item in the OPTION menu to HIGH.

A note of precaution when cleaning the air ﬁlter.

Please immediately turn the power off, and clean or change the air ﬁlter referring to the “Air Filter” section of this manual. After you have cleaned or changed the air ﬁlter, please be sure to reset the ﬁlter timer

(38).

Troubleshooting

Regarding the indicator lamps

Lighting and ﬂashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please follow the instructions within the table. If the same indication is displayed after the remedy, or if an indication other than the following is displayed, please contact your dealer or service company.

POWER

indicator

Lighting

In Orange

Blinking

In Green

Lighting

In Green

Blinking

In Orange

Blinking

In Red

Blinking

In Red

Lighting

In Red

Blinking

In Red

Lighting

In Red

LAMP

indicator

Turned

off

Turned

off

Turned

off

Turned

off

(discretionary)

Lighting

In Red

Blinking

In Red

TEMP

indicator

Turned

off

Turned

off

Turned

off

Turned

off

(discretionary)

Turned

off

Turned

off

Description

The projector is in a standby state.

Please refer to the section “Power On/Off”.

The projector is warming up.

Please wait.

The projector is in an on state.

Ordinary operations may be performed.

The projector is cooling down.

Please wait.

The projector is cooling down. A certain error has been detected.

Please wait until the POWER indicator ﬁnishes blinking, and then perform the proper measure using the item descriptions below.

The lamp does not light, and there is a possibility that interior portion has become heated.

Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufﬁciently cooled down, please make conﬁrmation of the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

• Is the air ﬁlter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the remedy, please change the lamp referring to the section “Lamp”.

The lamp cover has not been properly ﬁxed.

Please turn the power off, and allow the projector to cool down at least 45 minutes. After the projector has sufﬁciently cooled down, please make conﬁrmation of the attachment state of the lamp cover. After performing any needed maintenance, turn the power on again. If the same indication is displayed after the remedy, please contact your dealer or service company.

Regarding the indicator lamps (continued)

Troubleshooting

POWER

indicator

Blinking

In Red

Lighting

In Red

Blinking

In Red

Lighting

In Red

Lighting

In Green

Blinking in

Green for

approx. 3

seconds

LAMP

indicator

Turned

off

Turned

off

Simultaneous

blinking in Red

Turned

off

TEMP

indicator

Blinking

In Red

Lighting

In Red

Turned

off

Description

The cooling fan is not operating.

Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufﬁciently cooled down, please make conﬁrmation that no foreign matter has become caught in the fan, etc., and then turn the power on again. If the same indication is displayed after the remedy, please contact your dealer or service company.

There is a possibility that the interior portion has become heated.

• Is there blockage of the air passage aperture?

• Is the air ﬁlter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the remedy, please set FAN SPEED of the SERVICE item in the OPTION menu to HIGH.

It is time to clean the air ﬁlter.

Please immediately turn the power off, and clean or change the air ﬁlter referring to the section “Air Filter”. After cleaning or changing the air ﬁlter, please be sure to reset the ﬁlter timer. After the remedy, reset the power to ON.

At least 1 “Power ON” schedule is saved to the projector.

(Please refer to the User’s Manual-Network Functions: Schedule Settings for more information.)

NOTE • When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off. In such a case, press the “

” (OFF) side of the power switch, and wait at least 45 minutes. After the projector has sufﬁciently cooled down, please make conﬁrmation of the attachment state of the lamp and lamp

cover, and then turn the power on again.

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects

WARNING ►Never use the projector if abnormal operations such as

smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer or service company.

Before requesting repair, please check in

accordance with the following chart. This

operation sometimes resolves your problem. If the situation cannot be corrected,

The projector’s microprocessor may need to be

reset. Please push the Restart switch by using a cocktail stick or similar and

the projector will restart.

Some setting may be wrong. Please use the FACTORY RESET function of the

SERVICE item in the OPTION menu

Then, if the problem is not removed after the remedy, please contact your dealer or service company.

Phenomenon Cases not involving a machine defect

The electrical power cord is not plugged in.

Correctly connect the power cord.

The power switch is not set to the on position.

Set the power switch to [ | ] (On).

The main power source has been interrupted during

Power does not

come on.

Neither sounds

nor pictures are

outputted.

operation such as by a power outage (blackout), etc.

Please turn the power off, and allow the projector to cool down at least 2 minutes, then turn the power on again.

Either there is no lamp and/or lamp cover, or either of these has not been properly ﬁxed.

The signal cables are not correctly connected.

Correctly connect the connection cables.

Signal source does not correctly work.

Correctly set up the signal source device by referring to the manual of the source device.

The input changeover settings are mismatched.

Select the input signal, and correct the settings.

The RGB IN2 port is assigned to an RGB out while an RGB input signal is inputted to the port.

Push the RGB IN OUT switch to switch the function of the port.

(

39)



to reset all settings to factory default.

Reference

page

43, 44

12, 13

–

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

Phenomenon Cases not involving a machine defect

The signal cables are not correctly connected.

Correctly connect the audio cables.

Reference

page

12,13

The MUTE function is working.

Sound does not

come out.

No pictures are

displayed.

Restore the sound pressing the MUTE or VOLUME button on the remote control.

The volume is adjusted to an extremely low level.

Adjust the volume to a higher level using the menu function or the remote control.

The AUDIO setting is not correct.

Correctly set the AUDIO item in the SETUP menu.

The lens cap is attached.

Remove the lens cover.

The signal cables are not correctly connected.

Correctly connect the connection cables.

The brightness is adjusted to an extremely low level.

Adjust BRIGHTNESS to a higher level using the menu function or the remote control.

12, 13

The computer cannot detect the projector as a plug

Video screen

display freezes.

Colors have a

faded- out

appearance, or

Color tone is

poor.

and play monitor.

Make sure that the computer can detect a plug and play monitor using another plug and play monitor.

The FREEZE function is working.

Press the FREEZE button to restore the screen to normal.

Color settings are not correctly adjusted.

Perform picture adjustments by changing the COLOR TEMP, COLOR, TINT and/or COLOR SPACE settings, using the menu functions.

COLOR SPACE setting is not suitable.

Change the COLOR SPACE setting to AUTO, RGB, SMPTE240, REC709 or REC601.

25, 28,

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

Phenomenon Cases not involving a machine defect

Reference

page

The brightness and/or contrast are adjusted to an

Pictures appear

dark.

extremely low level.

Adjust BRIGHTNESS and/or CONTRAST settings to a higher level using the menu function.

The WHISPER function is working.

Select BRIGHT for the WHISPER item in the SETUP menu.

The lamp is approaching the end of its product lifetime.

Replace the lamp.

43, 44

Either the focus and/or horizontal phase settings are

Pictures appear

blurry.

not properly adjusted.

Adjust the focus using the focus ring, and/or H PHASE using the menu function.

The lens is dirty or misty.

Clean the lens referring to the section “Caring for the lens”.

NOTE • Although bright spots or dark spots may appear on the screen, this

is a unique characteristic of liquid crystal displays, and it does not constitute or

imply a machine defect.

Warranty And After-Service

Warranty and after-service

If a problem occurs with the equipment, ﬁrst refer to the “Troubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied.

Speciﬁcations

NOTE • These speciﬁcations are subject to change without notice.

Item Speciﬁcation

Product name Liquid crystal projector

Liquid Crystal panel

Lens Zoom lens F=1.7 ~ 1.9 f=18.9 ~ 22.6 mm Lamp 180W UHB Speaker 1W x 1 Power Supply AC100-120V/3.1A, AC220-240V/1.7A Power Consumption 290W Temperature range

Size

Weight (mass)

Ports

Optional parts

Panel size 1.5 cm (0.6 type) Drive system TFT active matrix Pixels 786,432 pixels (1024 horizontal x 768 vertical)

5 ~ 35°C (Operating) 306 (W) x 86 (H) x 249 (D) mm

(Not including protruding parts)

• Please refer to the following ﬁgure.

3.0 kg

RGB input:

RGB IN1 ..D-sub 15pin mini x1 RGB IN2 /OUT

D-sub 15pin mini ................x1

(select RGB IN2 or RGB OUT)

Audio input:

AUDIO 1 .......... Stereo mini x1

AUDIO 2 ..................... RCA x2

Audio output:

AUDIO OUT ... Lamp DT00731 Air ﬁlter Others • Please consult your dealer.

NJ22222

Stereo mini x1

Video input:

COMPONENT VIDEO

CB/P

(Y,

S-Video ................................

Video ....................................

Communication port:

CONTROL ............D-sub 9pin x1

USB ....................... USB(B) x1

LAN ..........................RJ-45 x1

B, CR/PR

) ...... RCA x3

1 1

Speciﬁcations

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN

RGB OU

AUDIO IN1

LAN

LINK

ACT

VIDEO

S-VIDEO

CB/PB

CR/PR

Speciﬁcations (continued)

249 mm100 mm

306 mm

86 mm

Projector

ED-X8255 only

User’s Manual – Network Functions

This manual is only intended to explain Network Functions. For safety, operations or any other issues, refer to the User’s Manual, Quick Start Guide or Safety Guide.

• Before using the network functions, read the User’s Manual

and Quick Start Guide carefully to ensure your projector is set up correctly.

• After reading, keep the manuals in a safe place for future reference.

WARNING

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

NOTE

Contents

Network Functions ..................................................................2

Settings ................................................................................... 6

Projector Control ...................................................................21

Failure & Warning Alerts via E-mail ......................................25

Projector Management via SNMP .......................................... 27

Controlling the Projector via Scheduling .............................. 28

e-Shot (Still Image Transfer) Display .................................... 31

Command Control via the Network ....................................... 33



Trademark acknowledgment

• Windows is a registered trademark of Microsoft Corporation.

• Netscape is a registered trademark of Netscape Communications Corporation.

• JavaScript is a registered trademark of Sun Microsystems, Inc. All other trademarks are the properties of their respective owners.

Network Functions

Conﬁguring and Controlling the Projector via a Web Browser

You can change the settings of or control the projector via a network by using a web browser from a PC that is connected to the same network.

(4)

Failure & Warning Alerts via E-mail

The projector can automatically send an alert to speciﬁed e-mail addresses when the projector requires maintenance or has encountered an error.

(25)

Projector Management via SNMP

This projector is SNMP (Simple Network Management Protocol) compliant, allowing you to monitor it from a remote location using SNMP software. In addition, the projector is able to send failure & warning alerts to a speciﬁed PC.

(27)

Controlling the Projector via Scheduling

You can schedule the projector to perform various functions according to the DATE and TIME.

(28)

Still Image Transfer

The projector can display still images that are transferred via the network.

(31)

Projector Control via RS-232C via the Network

The projector can be controlled using RS-232C commands over a network.

(33)

This projector is equipped with the following network functions.

Network Functions

Before using the network functions…

To use the network functions of this projector, the projector must be conﬁgured to suit your network. Consult with your network administrator before connecting the projector to your network. Incorrect network conﬁguration of this projector may cause problems on your network. Connect to the Gateway (The router/PC that forwards trafﬁc to a destination outside of the subnet of the transmitting device) from the network terminal on the projector using a CAT-5 cable and conﬁgure the following settings.

If using a network with DHCP enabled:

The projector’s network settings can be conﬁgured automatically. when

[DHCP] on the network menu is set to [TURN ON]. Please refer to DHCP in network menu. (User's Manual - Operating Guide : NETWORK Menu) If a ﬁxed / static IP address is required, please conﬁgure your projector according to the steps in the following section.

If using a network system that does not have DHCP enabled or if using a ﬁxed IP address on a network system equipped with DHCP enabled:

Conﬁgure the following settings on the network menu. (User's Manual - Operating Guide : NETWORK Menu)

[DHCP]: Disable DHCP (Set [DHCP] to [TURN OFF]).

[IP ADDRESS]: Enter an appropriate IP address for the projector to connect to your network.

[SUBNET MASK]: Enter an appropriate SUBNETMASK for the projector to connect to your network.

[DEFAULT GATEWAY]: Enter an appropriate Gateway (the router/PC that forwards trafﬁc to a destination outside of the subnet of the transmitting device) address for the projector to connect to your network.

Network Functions

Conﬁguring and controlling the projector via a web browser

You can adjust or control the projector via a network from a web browser on a PC that is connected to the same network.

• Internet Explorer 5.5 or higher or Netscape 6.2 or higher are required.

• If JavaScript is disabled in your web browser conﬁguration, you must enable JavaScript in order to use the projector web pages properly. See the Help ﬁles for your web browser for details on how to enable JavaScript.

• This projector is SSL (Secure Socket Layer) compliant. Please specify “https://” when the entering the projector address.

• If no operations are performed via a web browser for approx. 50 seconds the system will automatically log off. Please Re-log on to continue operations via a web browser.

• After you logon, a small, blank window will appear behind the main operation window. Please do not close this small, blank window. If this window is closed, the system will automatically log off after certain period of time even if an operation is being performed. The small, blank window will close when the main operation window is closed.

• The small, blank window may be considered a pop-up and be blocked if you are using Windows XP Service Pack 2, or using other security software. If Service Pack 2 blocks the window the following message will appear: "Pop-up blocked. To see this pop-up or additional options click here..." Please select "Temporarily Allow Pop-ups" or "Always Allow Pop-ups From This Site..." to allow the window to open.

• It is recommended that all web browser updates be installed. It is especially recommended that all users running Internet Explorer on a Microsoft Windows version prior to Windows XP Service Pack 2 install security update Q832894 (MS04-004) or the web browser interface may not be displayed correctly. And when using an older version of Internet Explorer, during operations the browser will log out after 50 seconds.

NOTE

Network Functions

When conﬁguring or controlling the projector via a web browser, an ID and password are required. There are two types of IDs, Administrator IDs and User IDs. The following chart describes the differences between user and administrator IDs.

Below are the factory default settings for administrator IDs, user IDs and passwords.

Item Description

Administrator ID

User ID

Network Information

Displays the projector’s current network conﬁguration settings.

√ √

Network Settings

Displays and conﬁgures network settings.

√ N/A

Port Settings

Displays and conﬁgures communication port settings.

√ N/A

Mail Settings

Displays and conﬁgures e-mail addressing settings.

√ N/A

Alert Settings

Displays and conﬁgures failure & warning alerts.

√ N/A

Schedule Settings

Displays and conﬁgures schedule settings.

√ N/A

Date/Time Settings

Displays and conﬁgures the date and time settings.

√ N/A

Security Settings

Displays and conﬁgures passwords and other security settings.

√ N/A

Projector Control Controls the projector. √ √

Projector Status

Displays and conﬁgures the current projector status.

√ √

Network Restart

Restarts the projector’s network connection.

√ N/A

Item ID Password

Administrator ID Administrator <blank> User ID User <blank>

Conﬁguring and controlling the projector via a web browser (Continued)

Settings

Refer to the following for conﬁguring or controlling the projector via a web browser. Example: If the IP address of the projector is set to 192.168.1.10:

1) Enter

[https://192.168.1.10] into the address bar of the web browser and the screen in Fig. 1 will be displayed.

2) Enter your ID and password and click

[Logon].

If the logon is successful either the Fig.2 or Fig.3 screen will be displayed.

3) Click the desired operation or conﬁguration item on the main menu located on

the left-hand side of the screen (Fig. 2 or Fig. 3).

Fig. 2 (Logon with administrator ID) Fig. 3 (Logon with user ID)

Fig. 1

Settings

Network Information

All screen images displayed in this manual are screens of a logon using an administrator ID. Any administrator only functions will not be displayed when using a user ID. Refer to the descriptions in each table.

Displays the projector’s current network conﬁguration settings.

Item Description

DHCP Displays the DHCP conﬁguration settings. IP Address Displays the current IP address. Subnet Mask Displays the Subnet Mask. Default Gateway Displays the Default Gateway.

MAC Address

Displays the MAC address.

Firmware Date

Displays the network ﬁrmware time stamp. This information is only displayed when logged on using an administrator ID.

Firmware Version

Displays the network ﬁrmware version number. This information is only displayed when logged on using an administrator ID.

Settings

Network Settings

Displays and conﬁgures network settings.

Click the [Apply] button to save the settings.

• The new conﬁguration settings are activated after restarting the network connection. When the conﬁguration settings are changed, you must restart the network connection. You can restart the network connection by clicking [Network Restart] on the main menu.

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

NOTE

Item Description

IP Conﬁguration Conﬁgures network settings.

DHCP ON Enables DHCP. DHCP OFF Disables DHCP.

IP Address Conﬁgures the IP address when DHCP is disabled. Subnet Mask Conﬁgures the Subnet Mask when DHCP is disabled.

Default Gateway Conﬁgures the Default Gateway when DHCP is disabled. Projector Name Conﬁgures the Projector name. SysLocation Conﬁgures the location to be referred to when using SNMP.

SysContact

Conﬁgures the contact information to be referred to when using SNMP.

Settings

Port Settings

Displays and conﬁgures communication port settings.

Click the [Apply] button to save the settings.

• The new conﬁguration settings are activated after restarting the network connection. The network connection must be restarted when the conﬁguration settings are changed. The network connection can be restarted using [Network Restart] on the main menu.dresses.

NOTE

Item Description

Network Control Port1

(Port:23)

Conﬁgures command control port 1 (Port:23).

Port open Click the [Enable] check box to use port 23.

Authentication

Click the [Enable] check box when authentication is required for this port.

Network Control Port2

(Port:9715)

Conﬁgures command control port 2 (Port:9715).

Port open Click the [Enable] check box to use port 9715.

Authentication

Click the [Enable] check box when authentication is required for this port.

Image Transfer Port

(Port:9716)

Conﬁgures the image transfer port (Port:9716).

Port open Click the [Enable] check box to use port 9716.

Authentication

Click the [Enable] check box when authentication is required for this port.

SNMP Port Conﬁgures the SNMP port.

Port open Click the [Enable] check box to use SNMP. Trap address Conﬁgures the destination of the SNMP Trap in IP format.

SMTP Port Conﬁgures the SMTP port.

Port open Click the [Enable] check box to use the e-mail function.

Settings

Mail Settings

Displays and conﬁgures e-mail addressing settings.

Click the [Apply] button to save the settings.

• You can conﬁrm whether the mail settings work correctly using the [Send Test Mail] button.

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

NOTE

Item Description

Send Mail

Click the [Enable] check box to use the e-mail function. Conﬁgure the conditions for sending email under

[Alert

Settings].

SMTP Server IP Address Conﬁgures the address of the mail server in IP format.

Sender E-mail address

Conﬁgures the sender e-mail address. The length of the sender e-mail address can be up to 255 alphanumeric characters.

Recipient E-mail address

Conﬁgures the e-mail address of up to ﬁve recipients. You can also specify [TO] or [CC] for each address. The length of the recipient e-mail address can be up to 255 alphanumeric characters.

Settings

Alert Settings

Displays and conﬁgures failure & warning alerts.

Item Description

Cover Error Conﬁgures Cover Error alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Fan Error Conﬁgures Fan Error alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e- mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Settings

Alert Settings (Continued)

Item Description

Lamp Error Conﬁgures Lamp Error alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Temp Error Conﬁgures Temp Error alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Air Flow Error Conﬁgures Air Flow Error alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Settings

Alert Settings (Continued)

Item Description

Lamp Time Error Conﬁgures Lamp Time Error alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Cool Error Conﬁgures Cool Error alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Filter Error Conﬁgures Filter Error alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Settings

Alert Settings (Continued)

Item Description

Other Error Conﬁgures Other Error alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Schedule Execution Error

Conﬁgures Schedule Execution Error alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Lamp Time Alarm Conﬁgures Lamp Time Alarm alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Settings

Alert Settings (Continued)

Item Description

Filter Time Alarm Conﬁgures Filter Time Alarm alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

“CHANGE THE LAMP” is displayed

Conﬁgures alert settings for when “CHANGE THE LAMP” is displayed.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Send Mail

Click the [Enable] check box to enable e-mail alerts for this item.

Mail Subject

Conﬁgures the subject line of the e-mail to be sent. The length of the subject line can be up to 255 alphanumeric characters.

Mail Text

Conﬁgures the text of the e-mail to be sent. The length of the text can be up to 1024 alphanumeric characters.

Cold Start Conﬁgures Cold Start alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Authentication Failure Conﬁgures Authentication Failure alert settings.

SNMP Trap

Click the [Enable] check box to enable SNMP Trap alerts for this item.

Click the [Apply] button to save the settings.

Settings

Schedule Settings

Displays and conﬁgures schedule settings.

Item Description

Daily Conﬁgures the daily schedule.

Schedule Click the [Enable] check box to enable daily scheduling. Schedule List Displays the current daily schedule.

Sunday Conﬁgures the Sunday schedule.

Schedule Click the [Enable] check box to enable Sunday scheduling. Schedule List Displays the current Sunday schedule.

Monday Conﬁgures the Monday schedule.

Schedule Click the [Enable] check box to enable Monday scheduling. Schedule List Displays the current Monday schedule.

Tuesday Conﬁgures the Tuesday schedule.

Schedule Click the [Enable] check box to enable Tuesday scheduling. Schedule List Displays the current Tuesday schedule.

Wednesday Conﬁgures the Wednesday schedule.

Schedule

Click the [Enable] check box to enable Wednesday scheduling.

Schedule List Displays the current Wednesday schedule.

Thursday Conﬁgures the Thursday schedule.

Schedule Click the [Enable] check box to enable Thursday scheduling. Schedule List Displays the current Thursday schedule.

Friday Conﬁgures the Friday schedule.

Schedule Click the [Enable] check box to enable Friday scheduling. Schedule List Displays the current Friday schedule.

Saturday Conﬁgures the Saturday schedule.

Schedule Click the [Enable] check box to enable Saturday scheduling. Schedule List Displays the current Saturday schedule.

Settings

Schedule Setting (Continued)

Item Description

Speciﬁc date No1 Conﬁgures the speciﬁc date (No.1) schedule.

Schedule

Click the [Enable] check box to enable speciﬁc date (No.1) scheduling.

Month/Day Conﬁgures the Month and date. Schedule List Displays the current speciﬁc date (No.1) schedule.

Speciﬁc date No.2 Conﬁgures the speciﬁc date (No.2) schedule.

Click the [Apply] button to save the settings.

Schedule

Click the [Enable] check box to enable speciﬁc date (No.2) scheduling.

Month/Day Conﬁgures the Month and date. Schedule List Displays the current speciﬁc date (No.2) schedule.

Speciﬁc date No.3 Conﬁgures the speciﬁc date (No.3) schedule.

Schedule

Click the [Enable] check box to enable speciﬁc date (No.3) scheduling.

Month/Day Conﬁgures the Month and date. Schedule List Displays the current speciﬁc date (No.3) schedule.

Speciﬁc date No.4 Conﬁgures the speciﬁc date (No.4) schedule.

Schedule

Click the [Enable] check box to enable speciﬁc date (No.4) scheduling.

Month/Day Conﬁgures the Month and date. Schedule List Displays the current speciﬁc date (No.4) schedule.

Speciﬁc date No.5 Conﬁgures the speciﬁc date (No.5) schedule.

Schedule

Click the [Enable] check box to enable speciﬁc date (No.5) scheduling.

Month/Day Set the Month and date. Schedule List Displays the current speciﬁc date (No.5) schedule.

Settings

To add additional functions and events click the [Add] button and set the following items.

Item Description

Time Conﬁgures the time to execute commands. Command Conﬁgures the commands to be executed.

Power Parameter Conﬁgures the parameters for power control.

Input Source Parameter

Conﬁgures the parameters for input switching.

Display Image Parameter

Conﬁgures the parameters for display of transfer image data.

Click the [Register] button to add new commands to the Schedule List.

Click the [Delete] button to delete commands from the Schedule list.

Date/Time Settings

Displays and conﬁgures the date and time settings.

Item Description

Current Date Conﬁgures the current date in Year/Month/Day format. Current Time Conﬁgures the current time in Hour:Minute:Second format.

Schedule Setting (Continued)

Settings

Date/Time Settings (Continued)

Click the [Apply] button to save the settings.

Item Description

Daylight Savings Time

Click the [ON] check box to enable daylight savings time and set the following items.

SNTP Server IP Address

Conﬁgures the SNTP server address in IP format.

Cycle

Conﬁgures the interval at which to retrieve Date and Time information from the SNTP server. (hours:minutes).

Start Conﬁgures the date and time daylight savings time begins.

Month Conﬁgures the month daylight savings time begins (1~12).

Week

Conﬁgures the week of the month daylight savings time begins (First, 2, 3, 4, Last).

Day

Conﬁgures the day of the week daylight savings time begins (Sun, Mon, Tue, Wed, Thu, Fri, Sat).

Hour Conﬁgures the hour daylight savings time begins (0 ~ 23). Minute Conﬁgures the minute daylight savings time begins (0 ~ 59).

End Conﬁgures the date and time daylight savings time ends.

Month Conﬁgures the month daylight savings time ends (1 ~ 12).

Week

Conﬁgures the week of the month daylight savings time ends (First, 2, 3, 4, Last).

Day

Conﬁgures the day of the week daylight savings time ends (Sun, Mon, Tue, Wed, Thu, Fri, Sat).

Hour Conﬁgures the hour daylight savings time ends (0 ~ 23). Minute Conﬁgures the minute daylight savings time ends (0 ~ 59).

Time difference

Conﬁgures the time difference (hours:minutes). Set the same time difference as the one set on your PC. If unsure, consult your network administrator.

SNTP

Click the [ON] check box to retrieve Date and Time information from the SNTP server and set the following items.

•

The new conﬁguration settings are activated after restarting the network connection. The network connection must be restarted when the conﬁguration settings are changed, The network connection can be restarted using [Network Restart] on the main menu.

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

• To enable the SNTP function, the time difference must be set.

• The projector will retrieve DATE and TIME information from the Timeserver and override time settings when SNTP is enabled.

• The Internal Clock’s time may not remain accurate. Using SNTP is recommended to maintain accurate time.

NOTE

Settings

Security Settings

Item Description

Administrator authority Conﬁgures the Administrator ID and Password.

Administrator ID

Conﬁgures the Administrator ID. The length of the text can be up to 32 alphanumeric characters.

Administrator Password

Conﬁgures the Administrator Password. The length of the text can be up to 255 alphanumeric characters.

Re-enter Administrator Password

Re-enter the above password for veriﬁcation.

Click the [Apply] button to save the settings.

Network Control

Conﬁgures the Authentication Password for the command control.

Authentication Password

Conﬁgures the Authentication Password. The length of the text can be up to 16 alphanumeric characters.

Re-enter Authentication Password

Used to re-enter the above password for veriﬁcation.

SNMP Conﬁgures the community name if SNMP is used.

Community Name

Conﬁgures the community name. The length of the text can be up to 64 alphanumeric characters.

Displays and conﬁgures passwords and other security settings.

User authority Conﬁgures the User ID and Password.

User ID

Conﬁgures the User ID. The length of the text can be up to 32 alphanumeric characters.

User Password

Conﬁgures the User Password. The length of the text can be up to 255 alphanumeric characters.

Re-enter User Password

Used to re-enter the above password for veriﬁcation.

NOTE

Projector Control

The items shown in the table below can be performed using the [Projector Control] menu. Select an item using the up and down arrow keys on the PC. Most of the items have a submenu. Refer to the table below for details.

Controls the projector.

Item Description

Main

Power Turns the power On/Off. Input Source Selects the input source. Picture Mode Selects the Picture Mode setting. Blank On/Off Turns Blank On/Off. Mute Turns Mute On/Off. Freeze Selects the Freeze setting. Magnify Controls the Magnify setting.

Picture

Brightness Adjusts the Brightness setting. Contrast Adjusts the Contrast setting. Gamma Selects the Gamma setting. Color Temp Selects the Color Temp setting. Color Adjusts the Color setting. Tint Adjusts the Tint setting. Sharpness Adjusts the Sharpness setting. Progressive Selects the Progressive setting. MyMemory Recall Recalls the MyMemory data. MyMemory Save Saves the MyMemory data.

Projector Control

Projector Control (Continued)

Item Description

Image

Aspect Selects the Aspect setting. Over Scan Selects the Over Scan setting. V Position Adjusts the V Position. H Position Adjusts the H Position. H Phase Adjusts the H Phase. H Size Adjusts the H Size. Auto Adjust Performs Auto Adjustment.

Input

Color Space Selects the Color Space. Component Selects the Component terminal setting. Video Format Selects the Video Format setting. Frame Lock Enables/Disables Frame Lock.

Setup

Keystone Adjusts the Keystone setting. Whisper Selects the Fan speed. (Normal or Whisper) Mirror Selects the Mirror status. Volume Adjusts the Volume setting. Audio-RGB1 Assigns the Audio-RGB1 input terminal. Audio-RGB2 Assigns the Audio-RGB2 input terminal. Audio-Video Assigns the Audio-Video input terminal. Audio-S-Video Assigns the Audio-S-Video input terminal. Audio-Component Assigns the Audio-Component input terminal.

Screen

Language Selects the Language for the OSD. Menu Position V Adjusts the vertical Menu Position. Menu Position H Adjusts the horizontal Menu Position. OSD Bright. Adjusts the OSD Brightness level. Blank Selects the Blank mode. Startup Selects the Startup screen mode. MyScreen Lock Turns MyScreen Lock On/Off. Message Turns the Message function On/Off.

Auto Search Turns the Automatic signal search function On/Off.

Auto Power off

Conﬁgures the timer to shut off the projector when no signal is detected.

Auto Adjust Enable Enables/Disables Auto Adjustment.

Projector Control

Projector Status

Displays and conﬁgures the current projector status.

Item Description

Error Status Displays the current error status

Lamp Time

Displays the usage time for the current lamp.

Filter Time Displays the usage time for the current ﬁlter. Power Status Displays the current power status. Input Status Displays the current input signal source. Blank On/Off Displays the Blank On/Off status. Mute Displays the current Mute On/Off status. Freeze Displays the current Freeze On/Off status. RGB2 Status Displays the current RGB2 terminal In/Out setting.

Projector Control (Continued)

Item Description

Option

Projector Control

Network Restart

Restarts the projector’s network connection.

Item Description

Restart

Restarts the projector’s network connection in order to activate new conﬁguration settings.

• Restarting requires you to re-log on in order to further control or conﬁgure the projector via a web browser.

NOTE

Logoff

When logoff is clicked, the logon screen is displayed (6 : Fig. 1).

Failure & Warning Alerts via E-mail

The projector can automatically send an alert to speciﬁed e-mail addresses when the projector requires maintenance or has encountered an error.

• Up to ﬁve e-mail addresses can be speciﬁed.

• The projector may be not able to send e-mail if the projector suddenly loses power.

NOTE

Mail Settings

(10)

To use the projector’s e-mail function please conﬁgure the following items via a web browser.

Example: If the IP address of the projector is set to 192.168.1.10:

• A Network Restart is required after the SMTP Port conﬁguration settings have changed. Click [Network Restart] and conﬁgure the following items.

NOTE

6) Click

[Mail Settings] and conﬁgure each item. Refer to the [Mail Settings] item in [Conﬁguring and Controlling the Projector via a Web Browser] for further information.

7) Click the [Apply] button to save the settings.

• Click the [Send Test Mail] button in [Mail Settings] to conﬁrm that the e-mail settings are correct. The following mail will be delivered to the speciﬁed addresses.

NOTE

Subject line : Test Mail <Projector name> Text : Send Test Mail Date <Testing date> Time <Testing time> IP Address <Projector IP address> MAC Address <Projector MAC address>

1) Enter [https://192.168.1.10] into the address bar of the web browser.

2) Enter the Administrator ID and Password and click

[Logon].

3) Click [Port Settings] on the main menu.

4) Click the [Enable] check box to open the SMTP Port.

5) Click the [Apply] button to save the settings.

Failure & Warning Alerts via E-mail

8) Conﬁgure the Failure/Warning Alerts via E-mail settings. Click [Alert Settings] on the main menu.

9) Select and conﬁgure each alert item. Refer to [Alert Settings] in [Conﬁguring

and Controlling the Projector via a Web Browser]

for further information.

10) Click the [Apply] button to save the settings.

Failure/Warning e-mails are formatted as follows:

Subject line : <Mail title> <Projector name> Text : <Mail text> Date <Failure/Warning date> Time <Failure/Warning time> IP Address <Projector IP address> MAC Address <Projector MAC address>

Mail Settings (Continued)

Projector management via SNMP

When SNMP is enabled, the projector is able to send Failure/Warning Alerts to a speciﬁed PC.

• It is recommended that SNMP functions be carried out by a network

administrator.

• SNMP management software must be installed on the computer to monitor the projector via SNMP.

NOTE

SNMP settings

Conﬁgure the following items via a web browser to use SNMP.

Example: If the IP address of the projector is set to 192.168.1.10:

• A Network Restart is required after the SNMP Trap conﬁguration settings have been changed. Click [Network Restart] and conﬁgure the following items.

NOTE

(9)

5) Click [Security Settings] on the main menu.

6) Click [SNMP] and set the Community Name on the screen that is displayed.

• A Network Restart is required after the Community Name has been changed.

• Click [Network Restart] and conﬁgure the following items.

NOTE

7) Conﬁgure the settings for Trap transmission of Failures/Warnings. Click [Alert Settings] on the main menu and select the Failure/Warning item to be conﬁgured.

8) Click the [Enable] check box to send out the SNMP trap for Failures/Warnings. Clear the [Enable] check box when SNMP trap transmission is not required.

9) Click the [Apply] button to save the settings.

1) Enter [https://192.168.1.10] into the address bar of the web browser.

2) Enter the Administrator ID and Password and click

[Logon].

3) Click [Port Settings] on the main menu.

4) Click the

[Enable] check box to open the SNMP Port.

Set the IP address to send the SNMP Trap to when a Failure/Warning occurs.

Controlling the Projector via Scheduling

The projector can be automatically controlled via scheduling.

• You can schedule the following control events: Power ON/OFF, Input

Source and Transferred Image Display.

• There are 3 types of Scheduling, 1) daily 2) day of the week 3) speciﬁc date.

• The priority for scheduled events is as follows 1) speciﬁc date 2) day of the week 3) daily.

• Up to ﬁve speciﬁc dates are available for scheduled events. Priority is given to those with the lower numbers when more than one event has been scheduled for the same date and time (e.g., ‘Speciﬁc day No. 1’ has priority over ‘Speciﬁc day No. 2’ and so on.

• Be sure to set the date and time before enabling scheduled events.

NOTE

Controlling the Projector via Scheduling

Date/Time Settings

The Date/Time setting can be adjusted via a web browser.

Example: If the IP address of the projector is set to 192.168.1.10:

• A Network Restart is required after the Daylight Savings Time or

SNTP conﬁguration settings have been changed.

• The battery for the built in clock may be dead if the clock loses time even when the DATE and TIME have been set correctly. Replace the battery by following the instructions on replacing the battery.

(User's Manual - Operating Guide : Replacing Internal Clock battery)

• The Internal Clock’s time may not remain accurate. Using SNTP is recommended to maintain accurate time.

NOTE

(18)

1) Enter [https://192.168.1.10] into the address bar of the web browser. Enter the Administrator ID and Password and click

[Logon].

2) Click [Date/Time Settings] on the main menu and conﬁgure each item. Refer to the [Date/Time Settings] item in [Conﬁguring and Controlling the

Projector via a Web Browser]

for further information.

3) Click the [Apply] button to save the settings.

Controlling the Projector via Scheduling

Schedule Settings

Schedule settings can be conﬁgured from a web browser.

Example: If the IP address of the projector is set to 192.168.1.10:

(16)

There are three types of scheduling.

1) Daily: Perform the speciﬁed operation at a speciﬁed time every day.

2) Sunday ~ Saturday: Perform the speciﬁed operation at the speciﬁed time on a speciﬁed day of the week.

3) Speciﬁc Date: Perform the speciﬁed operation on the speciﬁed date and time.

• In Standby mode the power indicator will ﬂash green for approx. 3

seconds when at least 1 “Power ON” schedule is saved.

• When the schedule function is used, the power cord must be connected to the projector and the outlet and the power switch must be turned on, [ | ]. The schedule function does not work when the power switch is turned off, [

] or the breaker in a room is tripped. The power indicator will lights orange or green when the projector gets is receiving the power.

NOTE

1) Enter [https://192.168.1.10] into the address bar of the web browser.

2) Enter the Administrator ID and Password and click

[Logon].

3) Click

[Schedule Settings] on the main menu and select the required schedule

item.

4) Click the [Enable] check box to enable scheduling.

5) Enter the Date (Month/Day) for speciﬁc date scheduling.

6) Click

[Add] and set the hour, command and parameters and click [Add This

Schedule] when you want to add a command.

7) Click the [Delete] button when you want to delete a schedule.

8) Click the [Apply] button to save the settings.

e-Shot (Still Image Transfer) Display

The projector can display a still image that is transferred via the network.

Communication Port

The following port is used for e-Shot. TCP #9716

(9)

e-Shot (Still Image Transfer) Settings

Conﬁgure the following items from a web browser when e-Shot is used.

Example: If the IP address of the projector is set to 192.168.1.10:

• e-Shot is not available via communication ports which are used for

the command control (TCP #23 and TCP #9716).

NOTE

1) Enter [https://192.168.1.10] into the address bar of the web browser.

2) Enter the Administrator ID and Password and click [Logon].

3) Click [Port settings] on the main menu.

4) Click the

[Enable] check box to open the

[Image Transfer Port (Port: 9716)]

. Click the [Enable] check box for the [Authentication] setting when authentication is required, otherwise clear the check box.

5) Click the [Apply] button to save the settings.

e-Shot (Still Image Transfer) Display

e-Shot (Still Image Transfer) Settings (Continued)

When the authentication setting is enabled, the following settings are required.

6) Click [Security Settings] on the main menu.

7) Select

[Network Control] and enter the desired authentication password. *

see Note1

8) Click the [Apply] button to save the settings. * see Note2

• The Authentication Password will be the same for [Network Control

Port1 (Port: 23)], [Network Control Port2 (Port: 9715)], and [Image Transfer Port (Port: 9716)].

NOTE1

• The new conﬁguration settings are activated after restarting the network. Restart the network connection when any conﬁguration settings are changed. The network connection can be restarted using [Network Restart] on the main menu.

NOTE2

e-Shot (Still Image Transfer) Transmission

e-Shot transmission requires an exclusive application for your PC. You can download it from the Hitachi web site. Refer to the manual for the application for instructions.

Command Control via the Network

You can conﬁgure and control the projector via the network using RS-232C commands.

Communication Port

The following two ports are assigned for the command control. TCP #23 TCP #9715

Command Control Settings

Conﬁgure the following items from a web browser when command control is used.

Example: If the IP address of the projector is set to 192.168.1.10:

• Command control is not available via communication port (TCP

#9716) that is used for the e-Shot transmission function.

NOTE

1) Enter [https://192.168.1.10] into the address bar of the web browser.

2) Enter the Administrator ID and Password and click

[Logon].

3) Click [Port settings] on the main menu.

4) Click the [Enable] check box to open [Network Control Port (Port: 23)] to use TCP #23. Click the

[Enable] check box for the [Authentication] setting when

authentication is required, otherwise clear the check box.

5) Click the

[Enable] check box to open [Network Control Port (Port: 9715)] to

use TCP #9715. Click the

[Enable] check box for the [Authentication] setting

when authentication is required, otherwise clear the check box.

6) Click the [Apply] button to save the settings.

(9)

Command Control via the Network

Command Control Settings (Continued)

When the authentication setting is enabled, the following settings are required.

(20)

7) Click [Security Settings] on the main menu.

8) Click

[Network Control] and enter the desired authentication password. * See

Note1.

9) Click the [Apply] button to save the settings. * See Note2.

• The Authentication Password will be the same for [Network Control

Port1 (Port: 23)], [Network Control Port2 (Port: 9715)], and [Image Transfer Port (Port: 9716)].

NOTE1

• The new conﬁguration settings are activated after restarting the network. Restart the network when any conﬁguration settings are changed. The network connection can be restarted using [Network Restart] on the main menu.

NOTE2

Command Control via the Network

Command format

Command formats differ among the different communication ports. TCP #23 You can use the RS-232C commands without any changes. The reply data format is the same as the RS-232C commands. However, the following reply will be sent back in the event of authentication failure when authentication is enabled.

Reply Error code

0x1F 0x04 0x00

TCP #9715

Send Data format

The following formatting is added to the header (0x02), Data length (0x0D), Checksum (1byte) and Connection ID (1 byte) of the RS-232C commands.

Header

Data

length

RS-232Ccommand

Checksum

Connection

0x02 0x0D 13 bytes 1 byte 1 byte

Header → 0x02, Fixed Data length → RS-232C commands byte length (0x0D, Fixed) RS-232C commands → RS-232C commands that start with 0xBE 0xEF (13 bytes) Check Sum → This is the value to make zero on the addition of the lower

8 bits from the header to the checksum.

Connection ID → Random value from 0 to 255 (This value is attached to

the reply data)

Command Control via the Network

Reply Data format

The connection ID (the data is same as the connection ID data on the sending data format) is attached to the RS-232C commands reply data.

Connection

0x06 1 byte

Connection

0x15 1 byte

Reply Error code

Connection

0x1C 2 bytes 1 byte

Reply Data

Connection

0x1D 2 bytes 1 byte

Reply Status code

Connection

0x1F 2 bytes 1 byte

Authentication

Error code

Connection

0x1F 0x04 0x00 1 byte

Command Control via the Network

Automatic Connection Break

The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established.

Authentication

The projector does not accept commands without authentication success when authentication is enabled. The projector uses a challenge response type authentication with an MD5 (Message Digest 5) algorithm. When the projector is using a LAN, a random eight bytes will be returned if authentication is enabled. Bind this received 8 bytes and the authentication password and digest this data with the MD5 algorithm and add this in front of the commands to send.

Following is a sample if the authentication password is set to “password” and the random eight bytes are “a572f60c”.

1) Select the projector.

2) Receive the random eight bytes “a572f60c” from the projector.

3) Bind the random eight bytes “a572f60c” and the authentication password “password” and it becomes “a572f60cpassword”.

4) Digest this bind “a572f60cpassword” with MD5 algorithm. It will be “e3d97429adffa11bce1f7275813d4bde”.

5) Add this “e3d97429adffa11bce1f7275813d4bde” in front of the commands and send the data. Send “e3d97429adffa11bce1f7275813d4bde”+command.

6) When the sending data is correct, the command will be performed and the reply data will be returned. Otherwise, an authentication error will be returned.

Projector

ED-X8255

User's Manual – Operating Guide Technical

Example of computer signal

Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode

720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.9 72.8 VESA VGA (72Hz) 640 x 480 37.5 75.0 VESA VGA (75Hz) 640 x 480 43.3 85.0 VESA VGA (85Hz) 800 x 600 35.2 56.3 VESA SVGA (56Hz) 800 x 600 37.9 60.3 VESA SVGA (60Hz) 800 x 600 48.1 72.2 VESA SVGA (72Hz) 800 x 600 46.9 75.0 VESA SVGA (75Hz) 800 x 600 53.7 85.1 VESA SVGA (85Hz)

832 x 624 49.7 74.5 Mac 16” mode 1024 x 768 48.4 60.0 VESA XGA (60Hz) 1024 x 768 56.5 70.1 VESA XGA (70Hz) 1024 x 768 60.0 75.0 VESA XGA (75Hz) 1024 x 768 68.7 85.0 VESA XGA (85Hz)

1152 x 864 67.5 75.0 VESA SXGA (75Hz)

1280 x 960 60.0 60.0 VESA SXGA (60Hz)

1280 x 1024 64.0 60.0 VESA SXGA (60Hz) 1280 x 1024 80.0 75.0 VESA SXGA (75Hz) 1280 x 1024 91.1 85.0 VESA SXGA (85Hz) 1600 x 1200 75.0 60.0 VESA UXGA (60Hz)

NOTE • Be sure to check jack type, signal level, timing and resolution

before connecting this projector to a computer.

• Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

• Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above.

• Although the projector can display signals with resolution up to UXGA (1600x1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and projector panel are identical.

• Automatically adjustment may not function correctly with some input signals.

• The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G.

Example of computer signal

Initial set signals

The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu.

Back porch (B) Front porch (D) Back porch (b) Front porch (d)

Data Data H. Sync. V. Sync.

Sync (A) Sync (a)

Display interval (C)

Display interval (c)

Computer/

Signal

TEXT 2.0 3.0 20.3 1.0 TEXT 3 42 400 1 VGA (60Hz) VGA (72Hz) 1.3 4.1 20.3 0.8 VGA (72Hz) 3 28 480 9 VGA (75Hz) 2.0 3.8 20.3 0.5 VGA (75Hz) 3 16 480 1 VGA (85Hz)

SVGA (56Hz) 2.0 3.6 22.2 0.7 SVGA (56Hz) 2 22 600 1 SVGA (60Hz) 3.2 2.2 20.0 1.0 SVGA (60Hz) 4 23 600 1 SVGA (72Hz) SVGA (75Hz) 1.6 3.2 16.2 0.3 SVGA (75Hz) 3 21 600 1 SVGA (85Hz) 1.1 2.7 14.2 0.6 SVGA (85Hz) 3 27 600 1

Mac 16" mode 1.1 3.9 14.5 0.6 Mac 16" mode 3 39 624 1

XGA (60Hz) 2.1 2.5 15.8 0.4 XGA (60Hz) 6 29 768 3 XGA (70Hz) 1.8 1.9 13.7 0.3 XGA (70Hz) 6 29 768 3 XGA (75Hz) XGA (85Hz) 1.0 2.2 10.8 0.5 XGA (85Hz) 3 36 768 1

1152 x 864

(75Hz)

1280 x 960

(60Hz)

1280 x 1024

(60Hz)

1280 x 1024

(75Hz)

1280 x 1024

(85Hz)

1600 x 1200

(60Hz)

Horizontal signal timing (μs)

(A) (B) (C) (D) (a) (b) (c) (d)

3.8 1.9 25.4 0.6 VGA (60Hz) 2 33 480 10

1.6 2.2 17.8 1.6 VGA (85Hz) 3 25 480 1

2.4 1.3 16.0 1.1 SVGA (72Hz) 6 23 600 37

1.2 2.2 13.0 0.2 XGA (75Hz) 3 28 768 1

1.2 2.4 10.7 0.6

1.0 2.9 11.9 0.9

1.0 2.3 11.9 0.4

1.1 1.8 9.5 0.1

1.0 1.4 8.1 0.4

1.2 1.9 9.9 0.4

Computer/

Signal

1152 x 864

(75Hz)

1280 x 960

(60Hz)

1280 x 1024

(60Hz)

1280 x 1024

(75Hz)

1280 x 1024

(85Hz)

1600 x 1200

(60Hz)

Vertical signal timing (lines)

3 32 864 1

3 36 960 1

3 38 1024 1

3 44 1024 1

3 46 1200 1

Connection to the ports

Y R

AUDIO IN

AUDIO OU

CONTROL RGB IN

RGB IN

USB

RGB OU

AUDIO IN

LAN

LINK

VIDE

S-VIDEO

B/PB

R/PR

Connection to the ports

RGB IN OUT switch

When this switch is not pushed in, RGB IN2 is selected.

When this switch is pushed in, RGB OUT is selected.

RGB IN1, BRGB IN2, RGB OUT

D-sub 15pin mini shrink jack

• Video signal: RGB separate, Analog, 0.7Vp-p,

5 4 3 2 1

10 9 8 7 6

14 13 12 11

75Ω terminated (positive)

• H/V. sync. Signal: TTL level (positive/negative)

• Composite sync. Signal: TTL level

At RGB signal At component video signal

Pin Signal

Video Red 2 Video Green 3 Video Blue 4 (No connection) 5 Ground 6 Ground Red 7 Ground Green 8 Ground Blue 9 (No connection)

10 Ground 11 (No connection)

: SDA (DDC data),

H. sync / Composite sync.

V. sync.

: SCL (DDC clock),

: (No connection)

Pin Signal

CR/P

CB/P

(No connection)

Ground

CR/PR Ground

Y Ground

CB/PB Ground

(No connection)

Ground

(No connection)

Except when set to RGB

OUT

Connection to the ports

Y R

AUDIO IN

AUDIO OU

CONTROL RGB IN

RGB IN

USB

RGB OU

AUDIO IN

LAN

LINK

VIDE

S-VIDEO

B/PB

R/PR

COMPONENT VIDEO CY, DCB/PB, ECR/P

RCA jack x3

• System: 525i(480i), 525p(480p), 625i(576i), 750p(720p), 1125i(1080i)

Port Signal

Y Component video Y, 1.0±0.1Vp-p, 75Ω terminator with composite CB/PBComponent video CB/PB, 0.7±0.1Vp-p, 75Ω terminator CR/PRComponent video CR/PR, 0.7±0.1Vp-p, 75Ω terminator

S-VIDEO

Mini DIN 4pin jack

Pin Signal

Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator

Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator Brightness signal, 1.0Vp-p, 75Ω terminator

Ground

VIDEO

RCA jack

• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL60

• 1.0±0.1Vp-p, 75Ω terminator

Connection to the ports

Y R

AUDIO IN

AUDIO OU

CONTROL RGB IN

RGB IN

USB

RGB OU

AUDIO IN

LAN

LINK

VIDE

S-VIDEO

B/PB

R/PR

1 2 3 4 5 6 7 8

AUDIO 1-IN (

Ø3.5 stereo mini jack),

I J

AUDIO 2 L/R (RCA jack)

• 200mVrms(max.) 35kΩ termination

AUDIO OUT (

Ø3.5 stereo mini jack)

• 200mVrms(max.) 1kΩ output impedance

USB

USB B type jack

CONTROL

D-sub 9pin plug

5 4 3 2 1

Pin Signal

1 +5V 2 - Data 3 + Data 4 Ground

9 8 7 6

• About the details of RS-232C communication, please refer to the following page. Pin Signal Pin Signal Pin Signal

1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CTS 3 TD 6 (No connection) 9 (No connection)

RJ-45 jack

Pin Signal Pin Signal Pin Signal

1 TX+ 4 - 7 2 TX- 5 - 8 3 RX+ 6 RX-

RS-232C Communication

1 2 3 4 5

789

CONTROL port RS-232C cable (Cross) RS-232C port of the projector of the computer

RD (2) (2) RD TD (3) (3) TD

- (4) (4) DTR GND (5) (5) GND

- (6) (6) DSR RTS (7) (7) RTS CTS (8) (8) DTS

- (9) (9) RI

- (1) (1) CD

1 2 3 4 5

789

Connecting the cable

Turn off the projector and the computer.

Connect the CONTROL port of the projector with a RS-232C port of

the computer by a RS-232C cable (cross). Use the cable that fulfills the

speciﬁcation shown in the previous page.

Turn the computer on, and after the computer has started up turn the

projector on.

Communications setting

19200bps, 8N1

1. Protocol

Consist of header (7 bytes) + command data (6 bytes).

2. Header

BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low : Lower byte of CRC ﬂag for command data CRC_high : Upper byte of CRC ﬂag for command data

3. Command data

Command data chart

byte_0 byte_1 byte_2 byte_3 byte_4 byte_5

low high low high low high

Action (byte_0 - 1)

Action Classiﬁcation Content

1 SET Change setting to desired value. 2 GET Read projector internal setup value. 4 INCREMENT Increment setup value by 1. 5 DECREMENT Decrement setup value by 1. 6 EXECUTE Run a command.

Action Type Setting code

RS-232C Communication (continued)

Requesting projector status (Get command)

(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+

‘00H’ +‘00H’) from the computer to the projector.

(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.

Changing the projector settings (Set command)

(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) +

setting code (2 bytes)) from the computer to the projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.

Using the projector default settings (Reset Command)

(1) The computer sends the default setting code Header + Command data (‘06H’+

‘00H’ + type (2 bytes) +‘00H’+‘00H’) to the projector. (2) The projector changes the speciﬁed setting to the default value. (3) The projector returns the response code ‘06H’ to the computer.

Increasing the projector setting value (Increment command)

(1) The computer sends the increment code Header + Command data (‘04H’+

‘00H’+ type (2 bytes) +‘00H’+‘00H’) to the projector. (2) The projector in creases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.

Decreasing the projector setting value (Decrement command)

(1) The computer sends the decrement code Header + Command data (‘05H’+

‘00H’+ type (2 bytes) +‘00H’ + ‘00H’) to the projector. (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.

When the projector cannot understand the received command

When the projector cannot understand the received command, the error code ‘15H’ is sent back to the computer. Sometimes the projector cannot properly receive the command. In such a case, the command is not executed and the error code ‘15H’ is sent back to the computer. If this error code is returned, send the same command again.

When the projector cannot execute the received command.

When the projector cannot execute the received command, the error code ‘1cH’ + ‘xxxxH’ is sent back to the computer. When the data length is greater than indicated by the data length code, the projector ignore the excess data code. Conversely when the data length is shorter than indicated by the data length code, an error code will be returned to the computer.

NOTE • Operation cannot be guaranteed when the projector receives an undeﬁned

command or data.

• Provide an interval of at least 40ms between the response code and any other code.

• The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data.

• Commands are not accepted during warm-up.

Hitachi ED-X8255F User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual