Hitachi DVPF3EUK User Manual

Download

Page 1

DVD/VCR Combo (DVD PLAYER with VIDEO CASSETTE RECORDER)

PROGRAM

VIDEO IN

TIMER REC

DVD OUTPUT VCR

(mono)

AUDIO IN R

AV 3

Recordable

ReWritable

INSTRUCTION MANUAL

VIDEO Plus+ and PlusCode are registered trademark of Gemstar Development Corporation.

PAL

MODEL

The VIDEO Plus+ system is manufactured under licence from Gemstar Development Corporation.

DVPF3EUK

Instruction manual

To obtain the best performance and ensure years of troublefree use, please read this instruction manual completely.

Page 2

WARNING

CAUTION - VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. AVOID EXPOSURE TO BEAM.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT KLASS 1 LASER APPARAT CLASSE 1 PRODUIT LASER

FUSE

BROWN

(Live)

CORD GRIP

OUTER SHEATH OF THE WIRE

BLUE

(Neutral)

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

LASER SAFETY

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.

CAUTION:

CAUTION: VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED.

LOCATION:

* PRINTED ON THE BACK

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

AVOID EXPOSURE TO BEAM.

CONNECTION TO POWER

Before Switching on make sure that the voltage of your electricity supply is the same as that indicated on the rating plate.

Mains Cord

This appliance may be fitted with a non-rewireable plug. If it is necessary to change the fuse in a non-rewireable plug the fuse cover must be refitted. If the fuse cover is lost or damaged, the plug must not be used until a replacement available from the appliance manufacturer is obtained. It is important that the colour of the replacement fuse cover corresponds with the rating marking on the base of the plug. If the plug has to be changed because it is not suitable for your socket, or becomes damaged, it should be cut off and an appropriate plug fitted following the wiring instructions below. The plug removed must be disposed of safely as insertion into a 13A socket is likely to cause an electrical hazard. For your own safety read the following instructions carefully before attempting to connect this unit to mains. The wires in this mains lead are coloured in accordance with the following code: BLUE=NEUTRAL, BROWN=LIVE

(For the area of Great Britain)

Important

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. No connection is to be made to the earth terminal of the plug. If a 13 Amp (BS 1363) Plug is used, a 3 Amp Fuse must be fitted, of if any other type of Plug is used a 3 or 5 Amp Fuse must be fitted, either in the Plug or Adaptor, or on the Distribution Board. Mains Supply: 220 - 240 V

50 Hz - AC only

Do not make any connection to the larger pin marked with the letter “E” or by the symbol or coloured green or green and yellow.

–2–

2C15

Page 3

PRECAUTIONS

POWER SUPPLY

The main power supply is engaged when the main plug is plugged in a 220-240V˜50Hz AC outlet. To operate the unit, press (Standby/ Power ON) to turn on the unit.

WARNING

TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE

1) Do not handle the power cord with wet hands.

2) Do not pull on the power cord when disconnecting it from AC wall outlet. Grasp it by the plug.

3) If, by accident, water is spilled on your DVD/VCR, unplug the power cord immediately and take the unit to our Authorized Service Center for servicing.

4) Do not put your fingers or objects into the DVD/VCR cassette holder.

5) Do not expose this unit to rain or moisture.

DEW WARNING

Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. Do not use the DVD/VCR Player at least for 2 hours until its inside is dry.

CAUTION

1) Do not attempt to open the cabinet. There are no parts you can service inside. Refer all servicing to qualified service personnel.

2) Slot and openings in the cabinet and at the side or bottom are provided for ventilation. To ensure reliable operation and to protect the unit from overheating these opening must not be blocked or covered. Avoid enclosed spaces such as book cases unless proper ventilation is provided.

3) Keep the unit away from the direct sunlight, the radiator heat sources, and dusty or humid places.

4) Avoid locations subject to strong vibration or strong magnetic fields.

5) Do not push objects of any kind into this through the cabinet slot as they could touch current carrying parts or short circuit parts resulting in a fire or electric shock.

6) Never spill liquid of any kind on this unit. If liquid is spilled into the unit, consult qualified service engineer.

7) Use this unit in a horizontal (flat) position only.

8) This equipment is in Stand-by mode when it turns off while the power cord is connected.

9) Do not place anything directly on top of the DVD/VCR. Do not place the DVD/VCR directly on top of the TV.

WARNING:

LIVE PARTS INSIDE.

DO NOT REMOVE ANY SCREWS.

DECLARATION OF

CONFORMITY

This product complies with the requirement of the directives EMC-Directive: 89 / 336 / EEC Low Voltage Directive: 73 / 23 / EEC CE Marking: 93 / 68 / EEC

declare that the DVD/VCR player with video cassette recorder

DV-PF3E(UK)

are in compliance with following norms:

EN 55013: 2001, EN55020: 2002, EN61000-3-2: 2000, EN61000-3-3: 1995 + A1: 2001 EN60065: 1998 EN60825-1: 1994

–3–

2C15

Page 4

A NOTE ABOUT RECYCLING

JEC

QUICK-FIND

SURROUND

N/CLO

DISPLAY

SUBTITLE

TIMER

DISC

NAVIGATION

-P

)

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.

The serial number of this product may be found on the back of the DVD/VCR. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

ABOUT COPYRIGHT

Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

SUPPLIED ACCESSORIES

Remote control

DV-RMPF3E(UK) (TS18354)

Two AA batteries

Aerial Cable

75 ohm (TE15231)

SYMBOLS USED IN THIS MANUAL

The following symbols below appear in some headings and notes in this manual, with the following meanings!

VCR

: Description refers to playback of video cassette tapes.

DVD

: Description refers to playback of DVD video discs.

: Description refers to playback of audio CDs.

MP3

: Description refers to playback of MP3 discs.

QUICK

: Description refers to the items to be set in the QUICK mode.

–4–

2C15

Page 5

TABLE OF CONTENTS

■ LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

■

CONNECTION TO POWER (For the area of Great Britain) . . . . . . 2

■ PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

DEW WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

CAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . 3

■ ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

■ SUPPLIED ACCESSORIES. . . . . . . . . . . . . . . . . . . . . . . . . . 4

■ SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . 4

■ TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

■ FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

■ ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

DISC TYPES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

■ OPERATING CONTROLS AND FUNCTIONS . . . . . . . . . . . 8

FRONT PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

DISPLAYS DURING OPERATION . . . . . . . . . . . . . . . . . . . 12

LOADING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . 12

■ VCR/DVD SWITCHING. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

■ CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

REAR VIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

DVD/VCR TO TV CONNECTION . . . . . . . . . . . . . . . . . . . . 14

OTHER CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CONNECTION TO AN AUDIO SYSTEM . . . . . . . . . . . . . . 15

CONNECTION TO A TV (FOR DVD/VCR) . . . . . . . . . . . . 15

■ HI-FI STEREO SOUND SYSTEM . . . . . . . . . . . . . . . . . . . 16

SELECTING THE SOUND MODE . . . . . . . . . . . . . . . . . . . 16

■ PRESET FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

VIDEO CHANNEL SETTING . . . . . . . . . . . . . . . . . . . . . . . 17

SETTING THE CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

■ TUNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

AUTOMATIC TUNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

MANUAL TUNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

TO SKIP A PRESET CHANNEL . . . . . . . . . . . . . . . . . . . . . 20

CHANNEL ORDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

■ PLAYBACK FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

NORMAL PLAYBACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 21

PICTURE SELECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

■ RECORDING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 23

NORMAL RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

OTR (One Touch Recording) . . . . . . . . . . . . . . . . . . . . . . . . . 23

TIMER RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

HINTS FOR TIMER RECORDING . . . . . . . . . . . . . . . . . . . 25

TIMER RECORDING USING

THE VIDEO Plus+®SYSTEM . . . . . . . . . . . . . . . . . . . . . . . 26

PDC (Programme Delivery Control) . . . . . . . . . . . . . . . . . . . 27

AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

COPYING A VIDEO TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 28

A STATUS DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

TV COLOUR SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

AUTO REWIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

REAL TIME TAPE COUNTER . . . . . . . . . . . . . . . . . . . . . . 29

■ PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

GENERAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

DISC NAVIGATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

STEP BY STEP PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 30

RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

FAST FORWARD/REVERSE SEARCH . . . . . . . . . . . . . . . . 30

SLOW FORWARD / SLOW REVERSE . . . . . . . . . . . . . . . . 31

ZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

TRACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

TITLE / CHAPTER SEARCH. . . . . . . . . . . . . . . . . . . . . . . . 31

TIME SEARCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

MARKER SETUP SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . 32

REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

PROGRAMME (CD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

RANDOM PLAYBACK (CD) . . . . . . . . . . . . . . . . . . . . . . . . 33

MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

ON SCREEN INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 33

TRACK SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

RANDOM PLAYBACK (MP3). . . . . . . . . . . . . . . . . . . . . . . 34

PROGRAMME (MP3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

STEREO SOUND MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

CHANGING THE ON SCREEN DISPLAY . . . . . . . . . . . . . 35

PARENTAL CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

■ DVD SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

AUDIO SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

VIRTUAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

DISPLAY SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

■ TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . 39

■ MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

DISC HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

■ SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

■ BATTERY SAFETY GUIDELINES. . . . . . . . . . . . . . . . . . . 42

■ SUBSIDIARY INFORMATION . . . . . . . . . . . . . . . . . . . . . . 43

–5–

2C15

Page 6

FEATURES

DVD

¡Dolby Digital sound

This DVD/VCR can handle Dolby Digital surround sound with 5.1 channels when connected to a Dolby Digital decoder.

¡Still/fast/slow/step playback ¡Random playback for audio CD and MP3 ¡Programme playback for audio CD and MP3 ¡DVD menus in a desired language ¡Screen saver/Auto power-off functions

The screen saver programme starts when there is no input from the DVD/VCR for five minutes in the stop mode. When the screen saver programme is activated for 30 minutes, the power is automatically turned off.

¡Subtitles in a desired language ¡Selecting a camera angle ¡Choices for audio language and sound mode ¡Parental lock ¡Automatic detection of discs

This DVD/VCR automatically detects if the loaded disc is DVD, audio CD or MP3 on disc.

¡Playing an MP3 disc ¡Direct Search ¡On screen display

Information about the current operation can be displayed on the TV screen, allowing you to confirm the currently active functions (such as programme playback), on the TV screen using the remote control.

¡DTS (Digital Theater System)

You can enjoy 5.1channel surround system developed by the Digital Theater System co. which reproduces the original sound as truthfully as possible.

¡Search

Chapter search / Title search / Track search / Time search

¡Repeat

Chapter / Title / Track / Group / All / A-B

¡Zoom ¡Marker

The part designated by user can be called back.

Mode

Disc Navigation

Displays the first scenes of each chapter in a title.

¡Resume Play ¡Virtual Surround ¡Bit rate indication ¡DRC (Dynamic range control)

You can control the range of sound volume.

¡MPEG sound

This player can handle a disc that supports MPEG audio and is connected to a MPEG decoder.

VCR

Hardware specifications

¡AUDIO OUTPUT L/R jacks ¡Auto Head Cleaner ¡4 Head HiFi Stereo ¡On screen Display

¡PLL Synthesiser Tuner with 99 channels

Automatic functions

¡Auto power on system

¡Digital Auto Tracking (DTR)

Playback

¡Auto Repeat ¡2 Step Picture Search Operation ¡Index Search ¡Time Search

¡Quick-Find ¡NTSC Playback

Recording

¡1 Year, 8 events (including Daily and Weekly Timer

¡OTR (One Touch Recording)

¡PDC (Programme Delivery Control)

Mode

presettable

Automatically turns the VCR on when you insert the cassette.

Recording)

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

–6–

2C15

Page 7

ABOUT THE DISCS

Example

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2Chapter 3 Chapter 4

Example

Track 1 Track 2 Track 3 Track 4 Track 5 Track 6

Example

Group 1 Group 2

Track 1 Track 2 Track 1 Track 2Track 3 Track 4

PLAYABLE DISCS

The following discs can be played back on this DVD/VCR.

DVD video

Audio CD

MP3*

* Depending on the types or the writing method of the medium some

discs can not be played.

Some DVD-R, or CD-R/RW discs made on personal computers, or on DVD recorders may not be played back properly due to factors such as scratches, dirt or special properties of the disc.

Discs made on personal computers may not be played back properly due to different environments or the settings of the application you use. We recommend always to use the standardised, properly formatted discs. (Please contact the sales agency for more detail).

This player conforms to PAL / NTSC color systems. You cannot play discs recorded in other color systems such as SECAM.

¡Some discs include region codes as shown below.

¡The number inside the symbol refers to a region of the world, and

a disc encoded in a specific region format can only be played back on DVD/VCR with the same region code.

The following discs cannot be played back on this DVD/VCR.

DVD with region codes other than 2 or ALL.

DVD-ROM

DVD-RAM

CD-ROM

VSD

CDV (Only plays back the audio part.)

CD-G (Only plays back the sound.)

CD-I

SACD

Photo CD

Video CD

Any other discs without compatibility indications.

DVD-R*

CD-R/RW*

DISC TYPES

[

]

DVD

Data on a DVD is divided into sections called "titles", and then into subsections called "chapters", each of which is given a title or chapter number. Playback conditions are preset on some DVD video discs, and these playback conditions take priority over user operations on this DVD/VCR. If a function you selected does not run as desired, refer to the manual accompanying the disc.

[

AUDIO CD

Data on an audio CD is divided into sections called “tracks”, each of which is given a track number.

[

MP3

Data on an MP3 is divided into sections called "groups", and then into subsections called "tracks", each of which is given a group or track number.

]

–7–

2C15

Page 8

OPERATING CONTROLS AND FUNCTIONS

PROGRAM

VIDEO IN

TIMER REC

DVD OUTPUT VCR

(mono)

AUDIO IN R

AV 3

1 342

6810121420

791113171921 15

18 16

FRONT PANEL

REMOTE CONTROL

26 27

28 29 30 31

32 33 34 35

38 39

SEARCH MODE/

OPEN/CLOSE

QUICK-FINDSURROUND

A-B REPEAT

REPEAT

RETURN

INDEX SEARCH TIME SEARCH

MODE

CLEAR/C.RESET

ZOOM

AUDIO

SUBTITLE

ANGLE

TIMER

TOP MENU/VIDEO Plus+

ENTER

DISC

NAVIGATION

DVD

SLOW SPEED REC

SKIP PROG

DAILY/WEEKLY

DISPLAY

SETUP

VCR

EJECT

+10

1. Disc loading tray

2. OPEN/CLOSE Button(DVD) [page 29]

Press to insert discs into or remove them from the tray.

3. CASSETTE COMPARTMENT

4. POWER Light

Lights up when the power is on.

5. POWER/STANDBY Button

Press to turn the power on and off. (As to the indication of the Operate switch, “ I ” indicates ON and “y” indicates electrical power STANDBY.)

6. PROGRAM

(o/p)

Buttons [page 14]

In VCR mode, press to change TV programmes on the VCR; press to adjust the tracking during normal or slow motion playback; press to remove vertical jitter in a Still picture.

7. PLAY Button(VCR) [page 17]

Press to begin playback.

8. STOP/EJECT Button (VCR) [page 25] EJECT Button

Press to remove the tape from the VCR.

STOP Button

Press to stop the tape motion.

9. AUDIO In Jacks

Connect audio cables coming from the audio out jacks of a camcorder, another VCR, or an audio source here.

10. VIDEO In Jack

Connect a video cable coming from the video out jack of a camcorder, another VCR, or a video source (laser disc player, camcorder, etc.) here.

48 47 46 45

44 43

42 41

11. F.FWD Button (VCR) [page 22]

Press to rapidly advance the tape, or view the picture rapidly in forward during playback. (Forward Search).

12. REW Button (VCR) [page 22]

Press to rewind the tape, or to view the picture rapidly in reverse during the playback mode (Rewind Search).

13. REC Button (VCR) [page 23]

Press once to start a recording. Press repeatedly to start a One Touch Recording.

14. REC Light [page 23]

Lights up during recording.

15. TIMER Light [page 24]

This light glows when the DVD/VCR is in standby mode for a timer recording or during a One Touch Recording. It flashes if TIMER is pressed for a timer recording, but there is no tape in the DVD/VCR. It flashes when all timer recordings or One Touch Recording are finished.

16 VCR OUTPUT Light (Green) [page 12]

This light appears when the VCR output mode is selected. You can only watch tapes when the green VCR OUTPUT light is on. To make the green VCR OUTPUT light come on, VCR on the remote control or OUTPUT on the front panel.

17. OUTPUT Button [page 12]

Press to select DVD mode or VCR mode.

● You can switch the output mode either by pressing

OUTPUT on the front panel, or by pressing DVD or VCR on the remote control. However, if you press

OUTPUT on the front panel first, you need to reselect the corresponding mode by pressing DVD or VCR on the remote control.

18. DVD OUTPUT Light (Green) [page 12]

This light appears when the DVD output mode is selected. You can only watch DVDs when the green DVD OUTPUT Light is on. To make the green DVD OUTPUT light come on, press DVD on the remote control or OUTPUT on the front panel.

19. Display, Remote Sensor Window

20. PLAY Button (DVD) [page 29]

Press to begin playback.

21. STOP Button (DVD) [page 29]

Stops operation of the disc.

22. SURROUND Button [page 36]

Press to activate the virtual surround.

23.yy/I(POWER/STANDBY) Button

Press to turn the power on and off. (As to the indication of the Operate switch, “ I ” shows

ON and “yy/I” shows electrical power stand-by.)

24. A-B REPEAT Button [page 32]

Repeats playback of a selected section.

25. REPEAT Button [page 32]

Repeats playback of the current disc, title, chapter or track.

26. MODE Button [page 33]

Activates programme playback or random playback mode when playing CDs or MP3. Sets virtual surround.

27. ZOOM Button [page 31]

Enlarges part of a DVD-reproduced image.

–8–

2C15

Page 9

28. CLEAR/C.RESET Button

● DVD mode [page 31]

Press to reset the setting.

● VCR mode [page 20]

Press to reset the counter.

29. ANGLE Button [page 35]

Press to change the camera angle to see the sequence being played back from a different angle.

30. SUBTITLE Button [page 34]

Press to select the desired subtitle language.

30. TIMER Button [page 24]

Press to put the VCR into standby mode for a timer recording.

31. MENU Button

● DVD mode [page 30]

Press to display the menu of the Disc.

● VCR mode [page 17]

Press to access the VCR menu.

32. Arrow Buttons

● DVD mode

32.

p / o / B/ sButtons

Move the cursor and determines its position.

● VCR mode

32.

p / o Buttons

Press to enter digits when setting programme (For example: setting clock or timer programme). Press to select the setting modes from the on screen menu.

B Button

When setting programme (For example: setting clock or timer programme), press to determine your selection and proceed to the next step you want to input. Press to determine the setting modes from the on screen menu.

s Button

Press to cancel a setting of timer programme. Press to correct digits when setting programme (For example: setting clock or timer programme).

33. ENTER Button (DVD) [page 30]

Press to accept a setting.

34. RETURN Button (DVD) [page 32]

Returns to the previous operation.

35. DISC NAVIGATION Button [page 29]

Press to display the first scenes of each chapter of the title being played.

36. DVD Button [page 12]

Press to select DVD mode for the remote control.

● You can switch the OUTPUT mode either by pressing

OUTPUT on the front panel, or by pressing DVD or VCR on the remote control. However, if you press

OUTPUT on the front panel first, you need to reselect the corresponding mode by pressing DVD or VCR on the remote control.

37. SLOW Button [page 21]

During tape playback, press to view the video tape in slow motion. Press again to resume normal playback. This button does not affect DVD playback.

38. SKIP (

39. STOP ( C) Button

40. h Button

● DVD mode [page 29]

Press to skip Chapters or Tracks.

●

INDEX SEARCH Button (VCR) [page 22]

Press to perform Index Search.

● TIME SEARCH Button (VCR) [page 22]

Press to perform Time Search.

● DVD mode [page 29]

Press to stop the disc motion.

● VCR mode [page 21]

Press to stop the tape motion.

● DVD mode [page 30]

Press to view the DVD picture in fast reverse motion or to reverse playback of an Audio CD.

)Buttons

● VCR mode [page 22]

Press to rewind the tape, or to view the picture rapidly in reverse during the playback mode (Rewind Search).

41. PAUSE/STEP (k) Button

● DVD mode [page 30]

Press to pause Disc playback. Press repeatedly to advance the DVD picture step by step (or one frame at a time).

● VCR mode [page 21]

While recording, press to temporarily stop the recording (pause). Press a second time to resume normal recording. You can not pause a One Touch Recording. Or, press during tape playback to freeze the picture. Press to advance the picture one frame at a time during still mode

42. D Button

● DVD mode [page 30]

Press to fast forward the Disc. Press PAUSE/STEP, then press this button to begin slow motion playback. Press this button repeatedly to change the forward speed of slow motion.

● VCR mode [page 22]

Press to rapidly advance the tape, or view the picture rapidly in forward during playback (Forward Search).

43. PLAY (B) Button

● DVD mode [page 29]

Press to begin playback.

● VCR mode [page 21]

Press to begin playback.

44. PROG

45. REC Button (VCR) [page 23]

46. SPEED Button [page 23]

47. VCR Button [page 12]

48. SETUP Button [page 36]

. TOP MENU Button (DVD) [page 30]

(o/p)

Press to change TV channels on the DVD/VCR. Press to adjust the tracking during normal or slow motion playback; press to remove vertical jitter in a still picture.

Press once to start a recording.

Press to select the VCR’s recording speed (SP or LP)

Press to select VCR mode for the remote control.

● You can switch the OUTPUT mode either by pressing

OUTPUT on the front panel, or by pressing DVD or VCR on the remote control. However, if you press

OUTPUT on the front panel first, you need to reselect the corresponding mode by pressing DVD or VCR on the remote control.

Press to enter the setup mode.

Button [page 14, 21]

Press to bring up the Top Menu on a disc.

VIDEO Plus+ Button

(VCR) [page 26]

Press to programme timer recording with the VIDEO Plus+ system.

50. DISPLAY Button

● DVD mode [page 35]

Press to access or remove the display screen during DVD or Audio CD playback.

● VCR mode [page 28]

Press to access or remove the VCR’s On screen status display.

51. AUDIO Button

● DVD mode [page 34]

Press to select a desired audio language or sound mode.

● VCR mode [page 16]

Press to select a desired sound mode.

52. Number Buttons

● DVD mode [page 31]

Press to directly select a Track (Audio CD) for playback.

+10 Button:

When searching a TITLE, a CHAPTER, or a TRACK, use this button to enter numbers 10 and above. For example when entering ‘15’, press this button first ,then ‘5’.

–9–

2C15

Page 10

● VCR mode [page 19]

POWER/STANDBY Button

A-B REPEAT Button

REPEAT Button

MODE Button

SUBTITLE/TIMER Button

DVD VCRCD

• Turns the DVD/VCR on and off.

• Turns the player on and off. • Turns the DVD/VCR on and off.

• Marks a segment to repeat between A and B.

• Marks a segment

to repeat between A and B.

• Allows you to repeat play a Chapter or Title.

• Allows you to repeat play a Track or Disc.

ZOOM Button

• To set surround on/off.

• Allows you to program

a specific order or random playback.

• To set surround on/off.

• To magnify part

of picture (x2/x4)

ANGLE Button

• Accesses various camera angles on a disc.

• Accesses various subtitles on a disc.

AUDIO Button

DISPLAY Button

• Accesses various audio functions on a disc.

• To select STEREO, L-CH or R-CH.

• Displays the current disc mode.

SURROUND Button

• Displays the current disc mode.

• Displays the current time,

tape counter, channel.

• To activate the virtual surround.

• To search chapter or time.

• To rapidly return to

a location of disc.

• Search the markers.

OPEN/CLOSE/EJECT Button

• To search track or time.

• To rapidly return to

a location of disc.

SEARCH MODE /QUICK-FIND Button

NUMBER Buttons

• To open or close the disc tray. • To open or close the disc tray.

• To select chapter directly.

• To select track directly,

use display function.

Tour of the Remote Control

Buttons on remote control work in different ways for DVD, CD and VCR : Refer to the following table for correct use.

• Search the markers.

• To select channel.

DAILY / WEEKLY button

• Use when you record using VIDEO Plus+ system.

• Press to put the VCR into

standby mode for a timer recording.

• Press to eject the video cassette

from the VCR.

• To search and confirm the

contents of the recorded programme(s).

+10

DAILY/WEEKLY

• To select STEREO, L-CH R-CH, or normal.

• To activate the virtual surround.

SEARCH MODE

QUICK-FIND

ZOOM

DISPLAY

AUDIO

A-B REPEAT

REPEAT

SUBTITLE

MODE

ANGLE

SURROUND

EJECT

OPEN/CLOSE

TIMER

Press to select TV channels on the VCR. To select channels, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0 then 6.

DAILY/WEEKLY/Button

[page 26]

Press to select once, daily, everyday, or weekly when you programme the automatic timer recording using the VIDEO Plus+ system.

53. OPEN/CLOSE Button (DVD) [page 29]

54. SEARCH MODE/QUICK-FIND Button

● DVD mode [page 31]

Press to access or remove the Search display, which allows you to go directly to a specific Title/Chapter/Track/Time.

● VCR mode [page 22]

Press to use Quick-Find mode.

Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the DVD/VCR.

Press to open or close the disc loading tray.

57. EJECT Button (VCR)

Press to eject the video cassette from the VCR.

Notes

¡To use the remote control to operate the DVD and its features, press DVD on the remote control before pressing other

DVD. Verify that the green DVD OUTPUT Light is on.

¡To use the remote control to operate the VCR and its features, press VCR on the remote control before pressing other

VCR. Verify that the green VCR OUTPUT Light is on.

–10–

2C15

Page 11

SETUP

PROG

DVD

ENTER

SKIP

INDEX SEARCH TIME SEARCH

• The first scenes of each chapter of the title being played will be displayed.

• To select the VCR output mode.

• To use the remote contorol

in VCR mode.

• To view the tape in slow motion.

• To select the recoeding speed.

• To start a recording.

VCR Button

SLOW Button

SPEED Button

REC Button

DISC NAVIGATION Button

VCR

SLOW

SPEED

REC

ENTER/Arrow Button (UP/DOWN or LEFT/RIGHT Button)

SEARCH Buttons

DVD VCRCD

• Moves the cursor and determines its position.

SETUP Button

• Brings up the DVD player's Setup menu.

SKIP Buttons (DVD)

INDEX SEARCH /

TIME SEARCH Buttons (VCR)

PROGRAM Buttons

• To skip Chapters.

• Allows you to search

forward/backward through a disc (×2. ×8. ×50. ×100) .

STOP Button

PLAY Button

• To stop playback.

• Begin disc play.

PAUSE/STEP Button

• Advances playback one frame at a time.

• Moves the cursor and determines its position.

• Brings up the DVD player's Setup menu.

• To skip Tracks. • To perform INDEX or TIME

SEARCH.

• Allows you to search forward/backward through a disc (×16) .

• To stop playback.

• Pause disc play.

• Pause tape play or record.

• Press to exclusively control

the TV programmes.

• Begin disc play.

• To stop playback or record.

• Begin tape play.

DVD Button

• To use the remote contorol in DVD mode.

• To select the DVD output mode.

• Allows you to forward/backward

through a tape.

DISC

NAVIGATION

Tour of the Remote Control

CLEAR/C.RESET Button

• Clear the makers.

• Removes status No.

in program input.

• Clear the number that is entered incorrectly.

MENU Button

• Brings up the Menu on a disc.

TOP MENU/VIDEO Plus+ Button

• Brings up the Top Menu on a disc.

RETURN Button

• Returns to a previous menu.

• To reset the tape counter.

• Brings up the VCR Menu.

• Cannot use the ENTER button.

• To programme timer recording

with the VIDEO Plus+ system.

TOP MENU/VIDEO Plus+

RETURN

CLEAR/C. RESET

–11–

2C15

Page 12

DISPLAY DISPLAYS DURING OPERATION

Stays on when the inserted disc is being played back.

Lights up when a CD is inserted into the tray.

Lights up when a DVD is inserted into the tray.

Lights up when the inserted disc comes to a pause.

Stays on when the A-B repeat function is on.

Stays on when the repeat function is on.

Stays on when repeat track function is on.

Displays how long a current title or track has been played back. When a chapter or track has switched, the number of the new title, chapter or track is displayed.

Stays on when repeat title function is on.

Stays on when repeat chapter function is on.

Stays on when the inserted cassette is being played back.

Lights up when the playback is in a still or in a slow mode.

Stays on during playback when the repeat function is on.

Works as a tape counter(hour,minute only). Also displays a channel number, tape speed remaining time for OTR and current time.

No disc inserted / can not read

Tray open

Tray closed

Loading the Disc

When a disc is being Play back

DVD OUTPUT VCR

DVD

LOADING THE BATTERIES

1. Open the battery compartment cover.

2. Insert two AA batteries, with each one oriented correctly.

VCR

3. Close the cover.

Since this product comprises VCR and DVD players, it is necessary to select the correct output mode.

SWITCHING TO VCR MODE

Press VCR on the remote control.

(Verify that the VCR OUTPUT Light is lit.)

SWITCHING TO DVD MODE

Press DVD on the remote control.

(Verify that the DVD OUTPUT Light is lit.)

Notes

¡Pressing only OUTPUT on the front panel does not

switch the mode of the remote control. You always need to select the correct mode on the remote control too.

VCR/DVD SWITCHING

Notes

¡Do not mix alkaline and manganese batteries. ¡Do not mix old and new batteries.

PROGRAM

DVD OUTPUT VCR

AV 3

TIMERREC

(mono)

VIDEO IN

AUDIO IN R

DVD button

VCR button

VCR OUTPUT Light

OUTPUT button

DVD OUTPUT Light

–12–

SEARCH MODE/

A-B REPEAT

REPEAT

MODE

CLEAR/C.RESET

ZOOM

ANGLE

SUBTITLE

TIMER

TOP MENU/VIDEO Plus+

ENTER

RETURN

DISC

DVD

NAVIGATION

SLOW SPEED REC

PROG

SKIP

INDEX SEARCH TIME SEARCH

DV-PMPF3E(UK)

OPEN/CLOSE

EJECT3QUICK-FINDSURROUND

DAILY/WEEKLY

+10

DISPLAY8AUDIO

SETUP

VCR

2C15

Page 13

AERIAL

RF OUT

AV2 (DECODER)

DVD/VCR

AV1 (TV)

DVD

DIGITAL

AUDIO OUT

LRCOAXIAL OPTICAL

ANALOG

AUDIO OUT

S-VIDEO

OUT

VCR

2435678

REAR VIEW

CONNECTIONS

1. AERIAL Jack

Connect your antenna, Cable Box, or Direct Broadcast System.

2. RF OUT Jack

Use the supplied aerial cable to connect this jack to the ANTENNA IN Jack on your TV.

3. AV2 (DECODER)

Socket

Connect 21-Pin scart cable here and to the 21-Pin scart jack of a decoder.

4. AV1 (TV)

Socket

Connect 21-Pin scart cable here and to the 21-Pin scart jack of a TV.

5. S-VIDEO OUT Jack (DVD only)

Connect an optional S-Video cable here and to the S-Video In jack of a television.

6. ANALOG AUDIO OUT Jacks (DVD only)

Connect the supplied audio cables here and to the Audio In jacks of a television or other audio equipment.

DIGITAL COAXIAL AUDIO OUT

Jack

(DVD only)

Connect an optional coaxial digital audio cable here and to the Coaxial Digital Audio In jack of a decoder or audio receiver.

DIGITAL OPTICAL AUDIO OUT

Jack

(DVD only)

Connect an optional optical digital audio cable here and to the Optical Digital Audio In jack of a decoder or audio receiver.

9. AC POWER CORD

Connect to a standard AC outlet to supply power to the DVD/VCR.

–13–

2C15

Page 14

The following show examples of connections commonly used to connect the DVD/VCR to TV and other

RF OUT

AERIAL

to AERIAL

to RF OUT

(Back of the unit)

to aerial socket

(TV)

UHF

AERIAL

RF OUT

AV2 (DECODER)

DVD/VCR

AV1 (TV)

DVD

DIGITAL

AUDIO OUT

LRCOAXIAL OPTICAL

ANALOG AUDIO OUT

S-VIDEO

OUT

VCR

to 21-Pin

to 21-Pin Scart Jack

Decoder (Not supplied)

(TV)

to RF OUT

to aerial

socket

Scart Jack

AV1 (TV)

components.

Notes

¡Be sure to turn off the power to all components in the system before connecting another component.

¡Refer to the Instruction Manuals for your TV, stereo system and any other components to be connected to the

DVD/VCR.

DVD/VCR TO TV CONNECTION

1. Disconnect the TV’s power cord from the AC outlet.

Disconnect the UHF TV aerial cable from the TV

3. Connect the UHF TV aerial cable to the DVD/VCR.

4. Connect the DVD/VCR to the TV using the aerial cable.

5. Plug the Power cords of the DVD/VCR and TV into the

AC outlets.

OTHER CONNECTIONS

EURO SCART (AV) SOCKETS

Your DVD/VCR is provided with two Scart sockets which you may connect to other external devices with Scart sockets. We recommend this connection to ensure a better audio and picture quality. NICAM stereo sound is only achieved when using a SCART lead.

Euro Scart cables are obtainable at your dealer.

AV1 (TV) CONNECTION TO TV

If your TV has Scart sockets, you may connect your DVD/VCR’s AV1 (TV) scart socket to the Scart socket on the back of your TV. Please see the instruction manual for your TV.

AV2 (DECODER) CONNECTION FOR OTHER EXTERNAL DEVICES

The second Scart socket AV2 (DECODER) is designated for other external devices, e.g. decoder, another VCR, video camera and so on.

NOTE:

• If you want to connect a TV with Scart socket to your

DVD/VCR, the TV must be connected to the DVD/VCR through AV1 (TV). A connection to AV2 (DECODER) will not function correctly.

EXTERNAL INPUT MODE

To receive the signal from an external input (decoder, video camera, another VCR etc.), connect to the AV2 (DECODER) socket, and press PROG (o/p) or enter “002” with the Number Buttons to show “AV 2 ” on the TV screen. (“L2” will appear on the DVD/VCR display panel.) If you use the AV1 (TV) socket, press PROG (o/p) or enter “001” with the Number Buttons to appear “AV 1 ” on the TV screen. (“L1” will appear on the DVD/VCR display panel.) If you use the front AUDIO/VIDEO In Jacks, press PROG

(o/p) or enter “003” with number button to show “AV 3 ”

on the TV screen. (“L3” will appear on the DVD/VCR display panel.)

–14–

2C15

Page 15

ANALOG

AUDIO OUT

S-VIDEO

OUT

R L S-VIDEO IN

AV1 (TV)

COAXIAL

OPTICAL

ANALOG

AUDIO OUT

DIGITAL

AUDIO OUT

COAXIAL OPTICAL

CONNECTION TO AN AUDIO SYSTEM

AUDIO

Method 1

Stereo system

Audio Input Jacks

Method 2

Dolby Digital decoder,

DTS decoder, or

MPEG decoder

Digital Audio Input Jacks

DVD/VCR

Analog Audio

Out

(DVD only)

• Method 1 DVD/VCR + Stereo system

• Method 2 DVD/VCR + Dolby Digital decoder or DTS decoder

Notes

¡If output Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to BITSTREAM for

audio output in the setup mode. (See page 36)

¡If output DTS audio, connect to a DTS decoder, and set DTS to BITSTREAM for audio output in the setup

mode. (See page 36)

¡If you want to enjoy DTS audio, use a DIGITAL AUDIO OUT jack for the connection. (DTS can only be out

put through the DIGITAL AUDIO OUT jacks.)

¡If output MPEG audio, connect to a MPEG decoder, and set MPEG to BITSTREAM for audio output in the

setup mode. (See page 36)

¡Unless connected to a Dolby Digital decoder, a DTS decoder, or a MPEG decoder, set Dolby Digital, DTS, or

MPEG to PCM (or OFF) for audio output in the setup mode. Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers. (See page 36)

¡The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital sound

by an MD or DAT deck.

¡Set Dolby Digital, DTS, and MPEG to PCM (or OFF) for audio output in the setup mode for method 1 only.

Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers. (Refer to page 36 to set BITSTREAM for Dolby Digital, DTS, and MPEG.)

Digital Audio

Out

CONNECTION TO A TV (FOR DVD/VCR)

DVD/VCR

Analog Audio out

(DVD only)

• Method 1 DVD/VCR Player + TV with S-Video Input Jack

• Method 2 DVD/VCR Player + TV with 21 pin scart Jack

Basic Audio

AV Cable

S-Video

S-Video out (DVD only)

–15–

Method 1

Best picture

Cable

Good picture

21 pin Scart jack

EURO Audio/Video out

Method 2

Euro audio/video Cable

2C15

Page 16

Notes

¡If you use the Euro audio/video cable, it is not necessary to connect the analog audio cable. ¡Connect the DVD/VCR player directly to a TV. If the A/V cables are connected to a DVD/VCR, pictures may

be distorted due to the copy protection system.

HOW TO CONNECT TO A TV WITHOUT AUDIO/VIDEO INPUT JACKS

If your TV does not have a Scart jack, it is still possible to connect this DVD/VCR player to your TV’s 75ohm coaxial antenna terminal using a commercially available Stereo Audio/Video RF Modulator, not included. Connect the audio and video outputs of the DVD/VCR player to the audio and video inputs on the RF Modulator, and then connect the coaxial output of the RF Modulator (usually marked “TO TV”) to the 75 ohm coaxial antenna terminal on your TV. Follow the instruction supplied with the RF Modulator for more details.

If your TV’s 75 ohm coaxial antenna terminal is already occupied by an antenna or cable box connection, remove that cable from your TV’s antenna terminal and reconnect it to the coaxial antenna input terminal of the RF Modulator (usually marked “ANT IN”), then connect the RF modulator to your TV’s antenna terminal as described above.

Note

¡The picture quality from DVD discs will not be as good if the DVD/VCR player is connected to the TV’s

antenna terminal through an RF Modulator.

HI-FI STEREO SOUND SYSTEM

This DVD/VCR will record and playback Hi-Fi stereo sound. In addition it has a NICAM stereo sound decoder. This equipment will receive stereo and bilingual broadcasts and there are several ways of recording and playing back the sound.

SELECTING THE SOUND MODE

VCR

You can select each mode by pressing AUDIO on the remote control. Each mode is indicated on the TV screen as following.

•

During playback of the recorded tape in

•

Hi-Fi mode:

Mode

Stereo

Normal

AUDIO OUTPUT

Hi Fi L Audio

Hi Fi R Audio

Hi Fi L Audio

Hi Fi R Audio

Normal Audio

Display on

the TV screen

STEREO

RIGHT

- None -

LEFT

Reception of stereo broadcasts:

Mode

Stereo

Monaural

AUDIO OUTPUT

L Audio

R Audio

L Audio

R Audio

L+R Audio

Display on

the TV screen

STEREO

LEFT

RIGHT

- None -

Notes

¡If you play non-Hi-Fi tapes, the DVD/VCR will play automatically in monaural even if you select any mode. ¡If the stereo signal becomes weak, the broadcast is automatically recorded in monaural.

During reception of bilingual broadcasts:

Mode

MAIN

SUB

MAIN

SUB

AUDIO OUTPUT

Main Audio

Sub Audio

Main Audio

Sub Audio

Display on

the TV screen

MAIN

SUB

MAIN

SUB

–16–

2C15

Page 17

PRESET FOR USE

TIMER SET UP INITIAL

RF OUT CH 35

INITIAL

CH TUNING CLOCK RF OUT

VIDEO CHANNEL SETTING

VCR

Skip This Section When Connected By SCART. Video channel setting will be necessary, if your DVD/VCR is connected to the TV via the aerial cable.

• Use the remote control for this procedure.

1 Insert a pre-recorded tape into the

DVD/VCR.

• The DVD/VCR will turn on and start playback automatically. If playback does not start, press PLAY ( B).

2 Select and adjust your TV to channel 35.

• If the playback picture appears on the TV screen, continue with step 8.

• If channel 35 is employed for broadcasting, or interference lines appear on the picture, the RF converter must be set to a different channel between CH22 and CH69. Continue with step 3.

3 Press MENU. 4 Press Arrow (o/p) repeatedly to select

“INITIAL”. Then, press Arrow (

B).

8 Press STOP ( C ) to stop the tape.

Notes

• You may also access the RF OUT CH menu by pressing and holding MENU on the remote control for 3 seconds during power off until the RF OUT CH menu appears.

• If your DVD/VCR and TV are connected using a SCART cable there is no need to have the RF converter operating so it can be switched off and avoid the possibility of interference. To switch off the RF converter, follow the instructions for Video Channel Setting to step 6 then select channel 22 first and then press Arrow (o/p) so that “--” appears next to “RF OUT CH” on the TV screen and finally press MENU to finish.

5 Press Arrow (o/p) repeatedly to select “RF

OUT”. Then, press Arrow (

• The RF OUT CH menu will appear.

B).

6 Press Arrow (o/p) to select a channel

which is not used for broadcasts between channel 22 and channel 69 in your area, then press Arrow (

B).

7 Press MENU to exit.

• Set the TV channel to the RF OUT CHANNEL which was selected on the DVD/VCR. Then, press PLAY (B). A picture from the DVD/VCR will appear on the TV screen. If a picture does not appear, repeat steps 3 to 7 using a different channel which is not used for broadcasts.

–17–

2C15

Page 18

SETTING THE CLOCK

INITIAL

CH TUNING CLOCK RF OUT

CLOCK

YEAR 2 0 0 3 MONTH 0 1 DAY 0 1 WE HOUR

_ _

MINUTE

_ _

TIMER SET UP INITIAL

VCR

This DVD/VCR incorporates a 24-hour clock. The clock must be set for the Automatic Timer Recording function to operate correctly.

Your DVD/VCR is fitted with PDC (See page27). If the PDC signal is available in your area, your DVD/VCR can get the current time from your local PDC broadcast. It keeps track of the time constantly referring to the time broadcasted by your PDC broadcast. If you want to use this feature, refer to “AUTO CLOCK SETTING” in the next section.

MANUAL CLOCK SETTING

1 Press MENU.

Press

Arrow (o/p)

press

Arrow (B)

Press

Arrow (o/p)

press

Arrow (B)

Press

Arrow (o/p)

press Arrow (

Press

Arrow (o/p)

appears, then press

to select “INITIAL”,then

to select “CLOCK”, then

to select “MANUAL”,then

until the relevant year Arrow ( B)

6 Likewise, set the relevant month, day, hour,

and minute.

7 Press MENU to start the clock.

Notes

• In the steps 5 and 6, you can go back to the item you

want to correct by pressing Arrow (s ).

• Although seconds are not displayed, they begin counting from 00 when you exit by pressing MENU. Use this feature to synchronise the clock with the correct time.

• When unplugging the power-cord or if there is a power failure for more than thirty minutes, you may have to reset the clock.

AUTO CLOCK SETTING

1 Follow the steps through 1 to 3 in “MANUAL

CLOCK SETTING”.

2 Press Arrow (o/p) to select “AUTO”. Then,

press Arrow (

B) to select [ON].

3 Turn off the DVD/VCR once by pressing

(Standby/Power ON).

• The clock will appear on the TV screen when you turn on the DVD/VCR again.

Notes

• Channel Presetting must be set before the Auto Clock is set.

• The DVD/VCR refers to the channel which was memorised into position 01. The PDC channel must therefore be set to position

01.

• The clock cannot be set automatically if you are not receiving a channel that carries a time signal in your area. In this case, set the clock manually.

• Once the auto clock setting is performed, the DVD/VCR will correct the current time by receiving PDC broadcasts whenever you turn off the DVD/VCR.

• The DVD/VCR will correct the current time automatically at 8:00.

• Between 23:00~1:00, the AUTO CLOCK function does not work even if the DVD/VCR’s power is

Tuning of broadcast channels not already preset in the DVD/VCR can be performed in two ways.

AUTOMATIC TUNING

• By “AUTOMATICALLY” tuning channels and plac- ing them in sequential order in the DVD/VCR’s memory i.e. the first channel found will be memorised into the DVD/VCR’s channel position 1, the second channel found will be memorised into the DVD/VCR’s channel position 2 and so on.

• Execution of the “Automatic” tuning cancels all the preset channels. DO NOT use this feature if you intend to use some of the pre-tuned channels. Use the “Manual” tuning function to tune in the additional channels you require.

TUNING

MANUAL TUNING

• Each channel is tuned manually and individually. Follow the steps laid out in the “MANUAL TUNING” section.

Before you preset Channel ...

• It is necessary to set the video channel if your DVD/VCR is connected to the TV via the aerial cable, and TV channel 35 is employed for broadcasting, or interference lines appear on the picture. Please refer to “Video Channel Setting”.

–18–

2C15

Page 19

AUTOMATIC TUNING

VCR

You can programme the tuner to scan only the channels that you can receive in your area.

• Use the remote control for this procedure.

1 Turn on the TV and select the TV channel to

the video channel on the TV.

2 Press MENU.

3 Press Arrow (o/p) to select “INITIAL”, then

press Arrow (

B).

TIMER SET UP INITIAL

4 Press Arrow (o/p) to select “CH TUNING”,

then press Arrow (

B).

INITIAL

CH TUNING CLOCK RF OUT

5 Press Arrow (o/p) to select “AUTO”, then

press Arrow (

• The tuner scans and memorises all the active channels in your area. After scanning, the tuner stops on the lowest memorised channel.

• Sorting of TV channels from P01 to P06 will be performed automatically as follows.

P01: BBC1 P02: BBC2 P03: ITV P04: CH4 P05: CH5 *(P06: Sky News)

*If you are using a satellite receiver, turn it on and

select Sky News before commencing tuning.

To Select a Desired Channel

You can select a desired channel by using the PROG (o/p), or directly pressing Number on the remote control.

• Enter a channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0 and 6. If you only press 6, channel 6 will be selected after a brief delay.

• You can only select channels 1–99.

B).

CH TUNING

AUTO MANUAL MOVE

MANUAL TUNING

VCR

• Use the remote control for this procedure.

1 Press MENU. 2 Press Arrow (o/p) to select “INITIAL”, then

press Arrow (

B).

TIMER SET UP INITIAL

3 Press Arrow (o/p) to select “CH TUNING”,

then press Arrow (

B).

INITIAL

CH TUNING CLOCK RF OUT

4 Press Arrow (o/p) to select “MANUAL”,

then press Arrow (

B).

CH TUNING

AUTO MANUAL MOVE

5 Press Arrow (o/p) to select “POSITION”,

then press Arrow (

• When a weak signal is received in Manual Tuning mode, you can change the background to solid blue or the static screen by pressing CLEAR/C.RESET.

6 Press Number,

your desired position number, then press Arrow (

• You can select position number 01-99.

• If [ON] appears on the right side of “SKIP”, press

Arrow (o/p) to point to “SKIP”. Then, press Arrow (

B) to select [OFF].

• If you want to remove scrambled signals, press Arrow

(

o/p) repeatedly to point to “DECODER”. Then,

press Arrow (B) to select [ON].

B).

MANUAL

POSITION CHANNEL DECODER SKIP

Arrow (o/p) to select

P08

008 [OFF] [OFF]

7 Press Arrow (o/p) to select “CHANNEL”,

then press Arrow (

B).

8 Press Arrow (o/p) to start scanning.

• The DVD/VCR tuner will begin to search up or down automatically. When a channel is found, the DVD/VCR will stop searching and the picture will appear on the TV Screen.

• You can select desired channel number by using the Number Buttons. You must refer to the channel plan and press three digits to select the channel number. (To select channel 24, first press “0” and then press

“2” and “4”).

•

If this is the channel you want, press

Channel Plan

CH Indication TV Channel

01 – 10 IRA – IRJ, GAP

21– 69 E21 – E69

74 – 78 X, Y, Z, Z+1, Z+2

80 – 99,100 S1 – S20, GAP

121 – 141 S21 – S41

This DVD/VCR can receive Hyper and Oscar frequency bands.

Arrow (B)

9 Press MENU to exit.

Note

To confirm that a channel has been added, press PROG (o/p).

–19–

2C15

Page 20

TO SKIP A PRESET CHANNEL CHANNEL ORDER

VCR

The channels you can no longer receive or seldom watch can be set to be skipped when you access channels PROG (o/p).

• Use the remote control for this procedure.

1 Press MENU.

2 Press Arrow (o/p) to select “INITIAL”, then

press Arrow (

B).

TIMER SET UP INITIAL

3 Press Arrow (o/p) to select “CH TUNING”,

then press Arrow (

B).

INITIAL

CH TUNING CLOCK RF OUT

4 Press Arrow (o/p) to select “MANUAL”,

then press Arrow (

B).

CH TUNING

AUTO MANUAL MOVE

VCR

You can arrange the channels in any order you want as follows.

• Use the remote control for this procedure.

1 Press MENU.

2 Press Arrow (o/p) to select “INITIAL”, then

press Arrow (

B).

TIMER SET UP INITIAL

3 Press Arrow (o/p) to select “CH TUNING”,

then press Arrow (

B).

INITIAL

CH TUNING CLOCK RF OUT

4 Press Arrow (o/p) repeatedly to select

“MOVE”, then press Arrow (

B).

CH TUNING

AUTO MANUAL MOVE

5 Press or Arrow (o/p) repeatedly to select

the position number you want to change the channel, then press Arrow (

B).

5 Press Arrow (o/p) to select “POSITION”,

then press Arrow (

B).

6 Press Number, or Arrow (o/p) to select rel-

evant position number, then press Arrow (

B).

7 Press Arrow (o/p) to select “SKIP”, then

press Arrow (

• To memorise the channel again, press Arrow (B) “ON” will change to “OFF”.

B) to select [ON].

MANUAL

POSITION CHANNEL DECODER SKIP

P08 008

[OFF]

[ON]

8 Press MENU to exit.

Note

To confirm that a channel has been deleted, press PROG (o/p).

MOVE

P01: P02: P03: P04: P05:

Position Number

01 02

[ ]

03 04 05

P06:

P07:

P08:

P09:

P10:

Channel Number

• You cannot select a position number where “- -” appears next to the number. This is because SKIP is set to [ON] for this position number.

• When a weak signal is received in Channel Order mode, you can change the background to static blue by pressing CLEAR/C.RESET. If you press the button again, the background will return to the static screen.

6 Press Arrow (o/p) repeatedly until the

channel move to another position number, then press Arrow (

B).

MOVE

P01: P02: P03: P04: P05:

P06: P07: P08: P09: P10:

06 07 08 09

[ ]

01 02 10 04 05

7 Press MENU to exit.

–20–

2C15

Page 21

PLAYBACK FUNCTION

SET UP

AUTO REPEAT[ON

]

PICTURE[NORMAL

]

AUTO RETURN

TIMER SET UP INITIAL

NORMAL PLAYBACK

VCR

1 Insert a prerecorded tape. The DVD/VCR will

turn on.

If the safety tab has been removed, the

VCR will start playback automatically.

¡If a cassette is in DVD/VCR, STOP sym-

bol appears in TV screen when turning on the DVD/VCR(VCR mode).

2 Turn on the TV and select the video channel

on the TV.

3 Begin playback by pressing PLAY ( B).

Tracking adjustment will be done automatically

(Digital Tracking function) when you start playback. To adjust the tracking manually, press PROG (o/p) on the remote or PROGRAM (o/p) on the VCR.

¡When a tape has reached the end, the VCR will

rewind the tape to the beginning and eject the tape automatically.

4 To stop playback, press STOP ( C).

If no corresponding symbols appear on the display

when you press buttons such as PLAY, RECORD, D or E, that means no cassette tape is in the VCR. Please insert a tape.

Counter Reset

¡You can reset the counter by pressing

CLEAR/C.RESET on the remote control.

STILL/SLOW

You can freeze the picture on TV screen by pressing PAUSE/STEP during playback.

¡You can advance the picture one frame at a time by

pressing PAUSE/STEP (k) during the Still mode.

¡When the picture begins to vibrate vertically, stabi-

lize the picture by pressing PROG (o/p) in the STILL mode.

¡You can watch in the slow motion by pressing

SLOW during playback or the still mode. (The DVD/VCR mutes the sound during slow motion. You can control the speed by pressing g or h.)

¡If a noise bar appears on the TV screen, you can

reduce it by pressing PROG (o/p).

¡After the VCR has been in Still/Slow mode for 5

minutes, it will stop automatically to protect the tape and the video head from damage.

¡To return to playback, press PLAY ( B).

2 Press Arrow (o/p) to select

“SET UP”,

then press

Arrow ( B).

3 Press Arrow (o/p) to select "AUTO

REPEAT",

then press

Arrow ( B).

4 Begin auto repeat playback by pressing

Arrow ( "AUTO REPEAT".

When in Stop mode, Auto Repeat mode will start

automatically.

¡If the On screen menu still remains, press MENU

to exit the menu.

¡To cancel the Auto repeat mode, press Arrow (B) at

step [4] so that OFF appears next to "AUTO REPEAT".

B) so that ON appears next to

PICTURE SELECT

VCR

This function enables you to select the picture quality of a tape.

¡Use the remote control for this procedure.

1 Press MENU.

2 Press Arrow (o/p) to

select “SET UP”, then press Arrow (

3 Press Arrow (o/p) to

select “PICTURE”, then press Arrow (

4 Press Arrow (B) until the desired mode

(NORMAL, SOFT, or SHARP) is indicated on the TV screen.

Note

Once you select the Picture Select mode, it stays in effect even after you turn off the DVD/VCR.

B).

B) .

AUTO REPEAT PLAYBACK

This feature allows you to play a tape over and over.

1 Press MENU.

VCR

–21–

2C15

Page 22

SEARCH FUNCTIONS

VCR

PICTURE SEARCH

If you want to skip or repeat a scene during playback, press D or E.

¡Press it again and the VCR will now search at super

high speed. (This function will not work for a NTSC tape).

¡Press PLAY ( B) to return to normal playback.

QUICK-FIND

This function enables you to search and confirm the contents of the recorded programme(s) using the index mark.

¡Use the remote control for this procedure. ¡The tape must be fully rewound.

1 Press QUICK-FIND to skip to the beginning

of next programme

2 Press PLAY ( B) to view at normal speed

The Quick-Find is cancelled.

Notes

¡This function will not operate in the Recording

mode.

¡When you want to cancel the Quick-Find while in

progress, press STOP (C).

¡When the end of a tape is reached during the Quick-

Find, the tape will automatically rewind to the beginning. After rewinding finishes, the DVD/VCR will eject the tape.

INDEX SEARCH

¡The index mark will be made automatically when

REC is pressed. It will also be marked at the starting point of Timer recording and OTR.

¡The index mark is not recorded if the PAUSE/STEP

(k) is pressed and released during recording recording.

¡The time gap between index marks on the tape

should be greater than 1 minute for SP recording and 2 minutes for LP recording.

¡Use the remote control for this procedure .

1 Press INDEX SEARCH so that the Index

Search menu appears.

2 Enter the number of

recordings you wish to skip by pressing Arrow ( within 30 seconds.

o/p)

INDEX 03

Notes

¡Index Search can be set up to 20. ¡This function will not operate in the Recording

mode.

¡Operations must be followed up within 30 seconds,

from step 2 to 3. Otherwise the Index Search mode will be cancelled.

¡To exit the Index Search mode, press the MENU

step 2.

TIME SEARCH

This feature allows you to go to a specific point on a tape by entering the exact amount of time you wish to skip in order to reach the point.

¡Use the remote control for this procedure.

1 Press TIME SEARCH so that the Time

Search menu appears.

2 Enter your desired time to

skip by pressing Arrow (

o/p) within 30 seconds.

TIME 2 : 50

3 Press Arrow (s / B) to start time search.

The DVD/VCR begins rewinding or fast forwarding to the specified point. When 0:00 is reached, the DVD/VCR will start playback automatically.

¡If you want to go in the forward direction, press

Arrow ( B).

¡If you want to go in the reverse direction, press

Arrow (s ).

¡If you want to stop search function, press

STOP (C ).

¡After time search, the VCR will play the tape auto-

matically.

Notes

¡Time search can be set up to 9 hours 59 minutes

(9:59). When you press TIME SEARCH in step 2, it will increase the time by 15 minutes. In this case, Time Search can be set up to 9 hours 45 minutes (9:45).

¡This function will not operate in the Recording

mode.

¡Operations must be followed up within 30 seconds,

from step 2 to 3. Otherwise the Time Search mode will be cancelled.

¡To exit the Time Search mode, press the MENU in

step 2.

3 Press Arrow (s / B) to start index search.

The DVD/VCR begins rewinding or fast forwarding to the beginning of desired programme. When the preset programme is reached,the DVD/VCR will start playback automatically.

¡If you want to go in the forward direction, press

Arrow ( B). If you want to go in the reverse direction, press Arrow ({ ).

¡If you want to stop search function, press STOP ( C ). ¡After index search, the VCR will play the tape auto-

matically.

–22–

2C15

Page 23

RECORDING FUNCTION

Ta b

TYPE OF TAPE RECORDING/PLAYBACK TIME

TAPE SPEED

SP MODE LP MODE E-60 1 HOUR 2 HOURS E-120 2 HOURS 4 HOURS E-180 3 HOURS 6 HOURS E-240 4 HOURS 8 HOURS

TIMER SET UP INITIAL

VCR

It may be UNLAWFUL to record copyrighted material without the consent of the copyright owner. This DVD/VCR will operate with any cassette that bears the VHS mark. For best results, we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

¡You can prevent accidental

erasing of a recording by breaking off the erase prevention tab on the back edge of the cassette.

¡If you decide to record on the tape again, cover the

hole with plastic tape.

TWO DIFFERENT TAPE SPEEDS

Before recording, select the tape speed : SP mode (Standard Play) or LP mode (Long Play). The table below shows the maximum recording/playback time using E-60, E-120, E-180 or E-240 tapes in each mode.

NORMAL RECORDING

VCR

1 Insert a cassette tape with its erase preven-

tion tab in place.

(If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)

2 Press Number or PROG (o/p) to select the

channel to be recorded.

3 Press SPEED to select the tape speed

(SP/LP).

4 Press REC to begin recording.

The “REC” Light on the display comes on.

¡ ¡To temporarily stop recording or to resume it, press

PAUSE/STEP. After the VCR has been in Pause mode for 5 minutes, it will stop automatically to protect the tape and the video head from damage.

Press STOP ( C ) when recording is completed.

Note

¡When you wish to watch another programme while

recording, select desired channel on your TV.

OTR (One Touch Recording)

VCR

This feature allows you to set the recording length simply by pressing REC on the VCR.

¡REC on the remote control is not available for this proce-

dure.

1 Press REC to begin OTR. The REC, TIMER

Light comes on. Change the recording length by pressing REC repeatedly.

0:30 1:00.... 7:30 8:00

Normal recording

¡To check time remaining during an OTR, press

DISPLAY.

¡To change the recording length during an OTR,

press REC until the desired length appears.

¡To stop an OTR before recording is finished, press

STOP ( C ).

¡To cancel the OTR but continue recording, press

REC repeatedly until “I” appears in the upper left corner of the TV screen.

¡If a tape ends during OTR, the VCR will stop, eject

the tape, and switch to the DVD mode automatically as the TIMER light blinks. (If the DVD power is off, the VCR will become STANDBY status).

¡When OTR is finished , the VCR turns off automat-

ically. To use the VCR again, press TIMER on the remote, or STOP/EJECT on the DVD/VCR.

TIMER RECORDING

VCR

You may programme the DVD/VCR to start and end a recording while you are away. You can set eight programmes to record on specific days, daily or weekly within a 1 year period.

• Use the remote control for this procedure.

• Insert a cassette tape with its erase prevention tab in

place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)

1 Press MENU.

2 Press Arrow (o/p) to

select “TIMER”, then press Arrow (

B).

–23–

2C15

Page 24

Notes

TIMER NUMBER

START END

DATE

CHANNEL

PDC

SPEED

--/--

--:--

If you have not set the clock yet, “CLOCK” setting menu appears. If so, follow the steps outlined in the “Setting the Clock” section. Then, set the timer.

¡When you press Arrow (B) after pressing Arrow

(o/p) or during steps 3 to 10,the input mode will move to the next step.

¡If you do not press Arrow (B) within 5 seconds of

setting an item, the input mode will move to the next step.

¡Press Arrow (s) to go back one step from the cur-

rent setting during steps 4 to 10. If Arrow (s) is pressed when the TIMER NUMBER is flashing, the entire programme contents will be erased.

3 Programme number

flashes. Press Arrow

(

o/p) repeatedly until

the desired programme number appears. Then, press Arrow (

B).

4 Select once, daily, everyday, or weekly

recording.

For once-only recording: Press Arrow (o/p) repeat- edly until the relevant month appears. For daily recording: To record a TV programme at the same time on the same channel from Monday through Friday. While the month digit is flashing, press Arrow (o/p) repeatedly to select “MO-FR”. For everyday recording:To record a TV programme at the same time on the same channel every day. While the month digit is flashing, press Arrow (o/p) repeatedly to select “MO-SU”. For weekly recording: To record a TV programme at the same time on the same channel every week. While the month digit is flashing, press Arrow (o/p) repeatedly to select “W-MO” (Example: every monday).

5 For once-only recording only : Press Arrow

(

o/p) repeatedly until your desired day

appears.

6 Press Arrow (o/p) repeatedly until the rele-

vant start hour appears. Next, enter the minute digit.

7 Press Arrow (o/p) repeatedly until the rele-

vant end hour appears. Next, enter the minute digit.

8 Press Arrow (o/p) repeatedly until the rele-

vant channel number appears.

9 Press Arrow (o/p) repeatedly until your the

desired tape speed appears.

10 Press Arrow (o/p) repeatedly to set PDC

“ON” or “OFF”.

The Programme Delivery Control (PDC) is a very

convenient system which assures that the TV programmes you have programmed for timer recording will be recorded exactly from beginning to end (see page 27).

11 Press Arrow (B).

Programme 1 is now completed.

12 Press MENU to exit.

To set another timer programme, repeat steps 3 to 11.

13 Press TIMER to activate the timer.

TIMER light comes on.

¡ ¡As TIMER light comes on the DVD/VCR becomes

STANDBY status, and switches to DVD mode automatically.

When all timer recordings are finished, TIMER light will flash. To use the DVD/VCR again as usual, press TIMER to disable the flashing TIMER light, then Press DVD or the VCR to choose DVD or VCR mode, then continue with the other features as described in this manual.

–24–

2C15

Page 25

9:00 10:00 11:00

Programme 1

Programme 2

Programme 3

HINTS FOR TIMER RECORDING

VCR

¡If there is a power failure or the DVD/VCR is

unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.

¡If a tape ends during TIMER RECORDING, the

DVD/VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER light blinks. (If the DVD power is off, the VCR will become STANDBY status).

If a tape is not in the safety tab, the TIMER light flashes and timer recording will not operate. Please insert a recordable

When all timer recordings are finished, the TIMER light will flash. To use the press TIMER to disable the flashing TIMER light, then press VCR to select the VCR mode. Select either VCR or DVD mode, then continue with the other features as described in this manual.

When timer recordings are set, the TIMER light will come on. To use the for the recording, press TIMER so that TIMER light disappears. Press VCR to choose the VCR mode. Select either VCR or DVD mode, then continue with the other features as described in this manual.

In timer standby mode, VCR feature does not function.

To exit timer standby mode, press TIMER. The TIMER light disappears and you can operate the VCR.

If you want to use the DVD player during a VCR timer recording or while the TIMER light is on or flashes.

You can use the DVD player while the TIMER light is on or flashes, or during a timer recording. Press y/I to turn on the DVD player. ;Press DVD on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You don’t have to set the TIMER off to use the DVD only.

DVD/VCR

or does not have a

tape.

again as usual,

as usual until the time

3 Select the programme number you want to

check by pressing Arrow ( o/p ) .

The details of the selected programme appears on

the TV screen.

Go to the digit you want to change by pressing Arrow ( B /s) pressing

¡You may cancel the entire programme by pressing

Arrow (

. Then, enter correct numbers by

o / p ).

Arrow ( B /s ) while the programme number flashes.

4 Press MENU to exit.

5 Press TIMER to return to timer stand-by

mode.

TO AVOID OVERLAP OF TIMER PROGRAMMES

A timer programme will not work whilst another programme is under execution.

TO STOP AN AUTOMATIC TIMER PROGRAMME ALREADY STARTED

Press C/A on the DVD /VCR.

TO CHECK, CORRECT, OR CANCEL AN AUTOMATIC TIMER PROGRAMME

1 Press TIMER.

If the VCR’s power is off, press y/I instead of

TIMER, then go on to the next step.

¡If the DVD output mode is selected, you have to

switch it to the VCR mode by pressing the VCR on the remote control or the OUTPUT on the DVD/VCR.

2 Repeat steps 2 to 3 in the “ TIMER

RECORDING” section.

–25–

2C15

Page 26

TIMER NUMBER

START END

DATE

CHANNEL SPEED

06/05 SA

19:30 20:30 16 SP

PDC

OFF

TIMER RECORDING USING

VIDEO Plus+ system PlusCode No.

---------

123456789

VIDEO Plus+ system PlusCode No.

TIMER NUMBER

START END

DATE

CHANNEL

PDC

SPEED

06/05 SA 19:30 20:30 16 SP OFF

THE VIDEO Plus+

You can programme the timer using the PlusCode numbers that are printed in TV guide magazine. You can set eight programmes to record.

• Use the remote control for the this procedure.

• Insert a cassette tape with its erase prevention tab in

place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)

1 Press VIDEO Plus+ .

If you have not set the clock yet, “CLOCK” setting menu appears. If so, follow the steps outlined in the “Setting the Clock” section. Then, set the timer.

2 Press Number to set the

Plus Code number of the programme you want to record.

• Press Arrow (s) to go back one digit from current

digit while you set the PlusCode number.

3 Select once, daily, everyday, or weekly

recording.

For once-only recording:

Press VIDEO Plus+. For daily recording: To record a TV programme at the same time on the same channel from Monday through Friday. Press DAILY/WEEKLY repeatedly to select “DAILY (MO-FR)”, then, press VIDEO Plus+ . For everyday recording:To record a TV programme at the same time on the same channel every day. Press DAILY/WEEKLY repeatedly to select “DAILY (MO-SU)”, then, press VIDEO Plus+. For weekly recording: To record a TV programme at the same time on the same channel every week. Press DAILY/WEEKLY repeatedly to select “WEEK- LY ”, then, press VIDEO Plus+.

Note

• If the PlusCode number is not available, it will be cleared automatically when you press VIDEO Plus+. Enter the correct PlusCode number and press VIDEO Plus+ again.

•

If the VIDEO Plus+ number flashes when you press VIDEO Plus+, this means that the PlusCode number you entered was incorrect or the timer recording you just programmed and another timer recording overlap.

SYSTEM

VCR

Confirm the channel number, then, press Arrow (B)

• If your local channel information is programmed in DVD/VCR’s memory, your local channel number appears automatically.

• If your local channel information is not programmed in DVD/VCR’s memory, “– –” or an incorrect chan- nel number may appear. In this case, press Arrow (o /p) repeatedly until your desired channel number appears. Then, press Arrow (s).

• When you select the channel number using Arrow (o /p) it memorises in DVD/VCR’s memory.

Press

Arrow (o/p)

repeatedly until the desired tape speed appears.

Press

Arrow (o/p)

to choose “ON” or

“OFF”.

•

The Programme Delivery Control (PDC) is a very convenient system which assures that the TV programmes you have programmed for timer recording will be recorded exactly from beginning to end (see page 27).

7 Press MENU to exit.

8 Press TIMER to activate the timer.

The TIMER light on the display comes on.

–26–

2C15

Page 27

PDC (Programme Delivery Control)

VCR

The PDC system looks for the start signal several hours before published start time and for several hours afterwards. This means that if the programme is broadcast anytime during this period it will be recorded correctly. Please note that if you have set an incorrect TIMER setting, it will stay in the memory until you cancel it (see page 25 for details on how to cancel a programme).

AUTO RETURN

VCR

When timer recording is finished, the DVD/VCR will automatically rewind the tape to the beginning where it started recording. If there are any remaining programmes including Daily, Everyday, & Weekly, AUTO RETURN will not operate.

1 Press MENU. 2 Press Arrow (o/p) repeatedly to point to

“SET UP”, then press Arrow (

3 Press Arrow (o/p) to point to “AUTO

RETURN”, then press Arrow (

• [AUTO] will appear next to “AUTO RETURN”.

4 Press MENU to exit.

TO WATCH THE RECORDED TIMER PROGRAMME

Press TIMER to cancel the Timer Stand-by. Then, Select VCR mode by pressing VCR your remote. Press PLAY ( B).

B).

–27–

2C15

Page 28

CHANNEL

VIDEO IN

TIMER REC

DVD OUTPUT VCR

(mono)

AUDIO IN R

LINE 2

AERIAL

RF OUT

AV2 (DECODER)

DVD/VCR

AV1 (TV)

DVD

DIGITAL

AUDIO OUT

LRCOAXIAL OPTICAL

ANALOG AUDIO OUT

S-VIDEO

OUT

VCR

AV1 (TV)

Playing VCR

to the audio output jack

to 21-Pin Scart jack

to the video output jack

Recording DVD/VCR (this unit)

to AV1 (TV) Scart jack on the back of the DVD/VCR

Using AV from terminals

Using scart jacks

to 21-Pin Scart Jack

(TV)

COPYING A VIDEO TAPE

VCR

You can make copies of videotapes made by friends or relatives for your own enjoyment.

WARNING: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.

Connect the recording VCR (this unit), playing VCR (another VCR) and your TV as outline in the following diagram.

1 Insert a pre-recorded video cassette into

the playing VCR.

2 Insert a blank video cassette, or one you

want to record over, into the cassette compartment of the recording DVD/VCR.

3 Press SPEED on the remote control to

select the desired recording speed (SP/LP).

4 Select “AV2” or “AV3” position on the

recording DVD/VCR. See “OTHER CONNECTIONS” on page 14.

5 Press REC on the recording DVD/VCR.

6 Begin playback of the tape in the playback

VCR.

7 To stop recording, press STOP

recording DVD/VCR, then stop playback of the tape in the playing VCR.

( C )

on the

Notes

• For best results during dubbing, use the DVD/VCR’s front panel controls whenever possible. The remote control might affect the playback DVD/VCR's operation.

• If video or colour fades in and out, you may be copying a copy guarded video tape.

TO MONITOR THE RECORDING

Turn on the TV and select the video channel on the TV.

A STATUS DISPLAY

VCR

To check the Counter, or Clock & Channel number, press DISPLAY. Each time you press the DIS-

PLAY, TV screen will change as illustrated: When you select the channel using the remote control number buttons, select the desired channel (position number).

Press once.

■

0:12:34

Press once.

<CLOCK and CHANNEL

NUMBER mode>

■

17:40

P02

TV COLOUR SYSTEM

Different countries use different television colour systems. Tapes recorded in the PAL or NTSC system can be played back on this unit. Usually, the picture on the TV screen will be in black and white when you play back a tape that is recorded in a different colour system.

•

Tapes recorded in the NTSC system can be played back on this unit and a PAL system TV set. This feature is only available in the SP mode. When playing back such tapes, the picture may roll up or down, shrink vertically and black bars may appear both at the top and bottom of the screen. Adjust the vertical hold control on your TV, if the TV features this control.

–28–

VCR

2C15

Page 29

AUTO REWIND

When a tape reaches the end during recording, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding finishes, the DVD/VCR will eject the tape.

¡The DVD/VCR will not rewind the tape automati-

cally during timer recording or Instant Recording Timer.

PLAYING A DISC

REAL TIME TAPE COUNTER

¡This shows the elapsed recording or playback time

in hours, minutes, and seconds. (The displayed time will not change during blank portions of the tape. The front display of DVD/VCR will show in hour, minute only.)

¡The ‘

’ indication will appear when the tape is

rewound further than “0:00:00” on the tape counter.

BASIC PLAYBACK

DVD

Getting started

¡Turn on the power of the TV, amplifier and any other

components which are connected to the DVD/VCR.

¡Make sure the TV and audio receiver (commercially

available) are set to the correct channel.

¡Select DVD mode by pressing DVD on the remote

control or output on the front panel.

¡When you play NTSC disc, the NTSC signal will

convert to a modified PAL signal.

1 Press y/I.

Check that the DVD OUTPUT Light is lit. If not,

press DVD on the Remote control to switch to DVD mode.

2 Press OPEN/CLOSE to open disc loading

tray.

3 Place the chosen disc

in the tray, with the label facing up.

¡DVDs recorded with the NTSC system can playback

with this unit via a PAL system TV set. Depending on the TV, when playing back a NTSC DVD on a PAL TV, the picture may roll up or down, shrink vertically and black bars may appear both at the top and bottom of the screen.

¡If a disc is dirty or has scratches, the pictures may

appear distorted and the playback operation may stop. In such cases, clean the disc and unplug the power cord and then plug it again before resuming playback.

GENERAL FEATURES

DVD may contain menus to navigate the disc and access special features. Press appropriate numerical button or use Arrow (L/K/B/s) to highlight your selection in the DVD main menu and press ENTER to confirm.

Note

¡Unless stated, all operations described are based on

remote control use. Some operations can be carried out using the menu bar on the TV screen.

DISC NAVIGATION

DVD

4 Press PLAY

The tray will close automatically, and playback will

then start from the first chapter or track of the disc. If the playback does not start automatically, press PLAY

( B)

¡When you playback a DVD with a title menu

recorded, it may appear on the screen. In this case, refer to “TITLE MENU” on page 30.

5 Press STOP

Notes

¡A “prohibited icon” may appear at the top-right

on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD/VCR or the disc.

¡With DVDs that use titles for playback programme

signals, playback may start from the second title, or it may skip these titles.

¡During the playback of a two layered disc, pictures

may stop for a moment. This happens when the 1st layer switches to the 2nd layer. This is not a malfunction.

( B )

( C )

to stop playback.

1 Press DISC NAVIGATION.

DURING TITLE PLAYBACK OR WHEN RESUME IS ON:

¡A shot from each chapter including the one current-

ly being played will be displayed on the screen.

¡The chapter currently being played is selected in yel-

low.

IN STOP MODE (RESUME OFF):

¡The first scene of each chapter of the first title will

be displayed.

2 Press Arrow (K/L/s /B) to select your

desired chapter.

Up to 6 chapters can be displayed at one time. If

the title has more than 6 chapters, press SKIP G to go to the next page. Press SKIP H to go back to the previous page.

¡You can change the title by moving up to the field

where the title number is shown with Arrow (K), and entering a title number of your choice.

–29–

2C15

Page 30

3 Press ENTER or PLAY

Playback of the selected chapter will start.

( B)

Notes

¡Pressing DISC NAVIGATION before pressing ENTER or

PLAY at step 3 will cease the DISC NAVIGATION function, and the playback will be stopped. The resume information will be lost.

¡When a disc menu is shown, the DISC NAVIGATION

feature does not function.

¡DISC NAVIGATION takes a few seconds to respond. ¡With some discs, part of the DISC NAVIGATION screen

may not be displayed properly. This is not a malfunction.

¡Some discs do not support DISC NAVIGATION feature. ¡While the DISC NAVIGATION is on the screen, the

sound is muted.

¡It takes about 15 seconds to display 6 shots.

CALLING UP A MENU SCREEN DURING PLAYBACK

For DVDs

¡Press MENU to call up the DVD menu. ¡Press TOP MENU to call up the title menu.

Note

¡Contents of menus and corresponding menu opera-

tions may vary between discs. Refer to the manual accompanying the disc for details.

STEP BY STEP PLAYBACK

DVD

1 During playback, press PAUSE/STEP(

Playback will pause and sound will be muted.

PAUSE

DVD

1 During playback, press PAUSE/STEP (

Playback will pause and sound will be muted.

2 To continue playback, press PLAY

( B)

DISC MENU

1 Press MENU.

The DVD main menu will appear.

2 If the feature is not available, symbol

may appear on the TV screen.

3 If disc menu is available on the disc, audio

language, subtitle options, chapters for the title and other options will appear for selection.

4 Press Arrow (L/K/B/s) to select an item,

and ENTER to confirm selection.

TITLE MENU

DVD

2 The disc goes forward by one frame each

time PAUSE/STEP (

To exit step by step playback, press PLAY ( B).

Note

¡The resume playback takes a little longer to take

place compared to the normal playback.

) is pressed.

RESUME

DVD

1 During playback, press STOP

Resume message will appear on the TV screen.

2 Press PLAY

the point at which playback was stopped.

To cancel resume, press STOP twice.

¡ ¡If turn off the DVD/VCR, resume function can-

celled.

( B)

, playback will resume from

( C )

FAST FORWARD/REVERSE

DVD

1 During playback, press g or h repeat-

edly to select the required forward or reverse speed: x2, x8, x50, x100.

For audio CDs, the speed is fixed at ×16.

¡For MP3, the speed is fixed at ×8.

MP3CD

1 Press TOP MENU.

The title menu will appear.

2 If the feature is not available, symbol

may appear on the TV screen.

3 Press Arrow (L/K/B/s) to select an item,

and ENTER to confirm selection.

–30–

To return to normal playback, press PLAY ( B)

2C15

Page 31

SLOW FORWARD /

SLOW REVERSE

DVD

1 During playback, press PAUSE/STEP

2 Press g or h .

3 Press g or h repeatedly to select the

required speed: 1/16, 1/8, 1/2 of the normal playback.

To return to normal playback, press PLAY ( B).

(k)

Using SKIPH,

During playback, press SKIP G to move the next track. Press it repeatedly to skip subsequent tracks. Press SKIP H to go back to beginning of the current track. Press it repeatedly to go to the previous tracks.

¡Track number will appear briefly on the DVD/VCR

display panel.

¡If SKIP is pressed while the playback is paused, the

playback will be paused again after skipping to the next track.

Note

¡SKIP H, G are not available when playback is

stopped.

ZOOM

DVD

The Zoom function allows you to enlarge the video image and to pan through the enlarged image.

1 Press ZOOM during playback.

Playback will continue.

2 Press ZOOM repeatedly to select the

required zoom factor: x2, x4 or OFF.

3 Use the Arrow (K/L/ s / B) to move the

zoomed picture across the screen.

4 To exit zoom mode, press ZOOM to OFF.

Notes

¡Zooming function does not work while disc menu is

shown.

¡x4 zoom is not available on some discs.

TRACK

There are three ways to begin playback on an Audio CD at a specific Track.

Using the Numerical buttons

1 Press Numerical buttons to enter the

desired Track number.

Playback will start at the selected track.

¡ ¡For single digit tracks (1-9), press a single number

(eg. track 3, press 3).

¡To play track 26, press +10, 2, 6 on the numerical

button.

TITLE / CHAPTER SEARCH

DVD

1 Press SEARCH

MODE once for the Chapter search, twice for the Title search during playback.

2 Enter the desired chapter/title number using

numerical buttons.

Playback will start at the selected Chapter or Title.

¡ ¡Press CLEAR/C.RESET to erase the incorrect input.

For single digits press 0 first.

TIME SEARCH

DVD

1 During playback, press SEARCH MODE

three times (CD: twice) to display the Time Search on the TV screen.

2 Within 30 seconds, enter a desired disc

time using numerical buttons.

Playback will start at the specified time.

3 Press CLEAR/C.RESET to erase the incor-

rect input.

Using SEARCH MODE

1 Press SEARCH MODE.

The track search display appears.

2 Within 30 seconds, select a desired track

number using numerical buttons.

For single digits press 0 first.

¡ ¡Playback will start at the selected track. ¡Press CLEAR/C.RESET to erase the incorrect input.

–31–

2C15

Page 32

MARKER SETUP SCREEN

REPEAT TRACK

DVD

Use markers to memorise your favourite places on a disc.

1 Press SEARCH MODE four times (CD: three

times) during playback.

The display screen and Markers will appear on the TV screen.

2 Press Arrow (s/ B) to select 1, 2, 3, 4, 5, 6,

7, 8, 9, or 10 and ensure that “- :- - :- -” appears in the display.

3 When reaches the desired point, press

ENTER.

The Title or Track and elapsed playing time will appear in the TV screen.

4 To return to the Marker later, press SEARCH

MODE four times (CD: three times) during playback and Arrow (s / B) to choose the desired marker, then press ENTER.

Notes

¡Opening the disc tray or turning off the power or

select AC at step 2 and press ENTER will erase all Markers.

¡To clear a marker, using Arrow (s / B

)

, position the cursor on to the marker number to be cleared and press CLEAR/C.RESET.

¡You can mark up to 10 points.

5 Press SEARCH MODE or RETURN to exit.

REPEAT

REPEAT is available only during playback.

REPEAT TITLE / CHAPTER

DVD

To activate the repeat function, press REPEAT during playback.

The repeat mode changes as described below every time you press the button.

To activate the repeat function, press REPEAT during playback.

The repeat mode changes as described below every time you press the button.

TRACK ALL OFF

(current track repeat) (entire disc repeat)

(repeat off)

Notes

¡Track repeat setting will be cleared when moving to

other track.

¡Repeat playback does not function during A-B

REPEAT playback.

MP3

TRACK GROUP OFF

(current track

repeat)

(current folder

repeat)

ALL

(entire disc

repeat)

(repeat off)

A-B REPEAT

DVD

1 Press A-B REPEAT at your chosen starting

point.

A- appears briefly on the TV screen.

2 Press A-B REPEAT again at your chosen

end point.

A-B appears briefly on the TV screen, and the

repeat sequence begins.

3 To exit the sequence, press A-B REPEAT.

Notes

¡The A-B REPEAT section can only be set within the

current title (for DVDs), or current track (for audio CDs).

¡A-B REPEAT is not available with some scenes in

DVD.

¡To cancel the A point which was set, press

CLEAR/C.RESET.

¡A-B REPEAT playback does not function during

title, chapter, track or all repeat playback.

CHAPTER TITLE OFF

(current chapter repeat) (current title repeat)

(repeat off)

Notes

¡Track Repeat Title/Chapter is not available with

some scenes.

¡The REPEAT setting will be cleared when moving

to other title or chapter.

–32–

2C15

Page 33

MP3 PLAYBACKPROGRAMME

TOTAL

You may determine the order in which tracks will play.

1 In stop mode, press MODE.

The PROGRAM screen will appear.

2 Press Arrow (▲ / ▼)

to select a track, then press ENTER.

Press CLEAR/C.RESET to erase the most recently entered programme.

3 Press PLAY

tracks.

Notes

¡While the programme is being played back, the

STOP works as follows.

¡Press STOP (C) once and then PLAY (B) again,

playback will restart from the point where STOP was pressed. (Programme continued)

¡Press STOP (C) twice and then PLAY (B) again,

playback will restart from the track in the usual way. (Programme cleared)

¡Up to 99 programmes can be entered. ¡If you like to repeat the current track in the pro-

gramme, press REPEAT repeatedly until TRACK appears during playback. If you like to repeat the entire programme press REPEAT repeatedly until ALL appears during playback.

TO CLEAR THE PROGRAMME

¡Open the disc loading tray, and the the programme

will be cleared.

( B)

to play the programmed

MP3

When a CD with MP3 files is inserted in the DVD/VCR, the MP3 menu will appear on the TV screen, and number of tracks is displayed on the front panel.

1 In stop mode, press Arrow (K/L) to select

the desired group track.

If a group is selected, press Arrow (B) or ENTER to go on to the track selection screen. Press Arrow (K/L) to choose a track, then press PLAY (B) or ENTER.

¡If a track is selected, press

PLAY (B)

or ENTER to start playing tracks. Starting from the one you’ve just chosen the subsequent tracks will be played.

¡Choose FIRST PLAY to start playback from the

beginning of the listed tracks.

¡Press TOP MENU to return to the first item.

2 Press STOP ( C ) to stop playback.

Notes

¡Folders are known as Groups; files are known as

Tracks.

¡MP3 files are accompanied by icon. ¡Maximum of 255 folders can

be recognised.

¡Maximum of 256 files can be recognised. ¡Up to 8 hierarchies can be created.

This player recommends the use of files recorded at the below specifications:

¡Sampling frequency: 44.1kHz or 48kHz ¡Constant bit rate: 112kbps ~ 320kbps.

RANDOM PLAYBACK

ON SCREEN

This shuffles the playing order of tracks instead of playback in the original sequence.

1 In stop mode, press

MODE twice.

RANDOM screen appears.

RANDOM

CD [AUDIO] TOTAL 0:45:55

PLAY

RANDOM PROGRAM

--no indication--

2 Press PLAY ( B)to start random playback.

Note

¡If you like to repeat the current track in the random

selection, press REPEAT repeatedly until TRACK appears during playback. If you like to repeat the entire random selection press REPEAT repeatedly until ALL appears during playback.

You can check the MP3 files during playback.

1 Press DISPLAY.

The name of the file currently in play will be dis-

played.

2 Press DISPLAY again to show the track

number, the repeat status, and the playback status at the top of the screen.

¡ will be displayed when repeat play has been

selected.

T - indicates Track repeat

G - indicates Group (folder) repeat

A - indicates ALL repeat

3 Press DISPLAY again to exit.

–33–

INFORMATION

MP3

2C15

Page 34

TRACK SELECTION

MP3

1 Press SEARCH MODE during playback.

The FILE LIST will appear.

2 Select a desired track using Arrow

(

K/L/s/B).

Press Arrow ( B) when you want to go to the next

hierarchy.

¡Press Arrow (s ) when you want to go back to the

previous hierarchy.

3 Press PLAY ( B) to start playing.

Notes

¡Press SEARCH MODE to EXIT. ¡Some selections may take a while to be recognised.

RANDOM PLAYBACK

MP3

¡Some discs allow audio language setting on the disc

menu. (Operation varies between discs, so refer to the manual accompanying the disc.)

¡If you choose a Language that has a 3 letter language

code, the code will be displayed every time you change the audio language setting. If you choose any other languages, ‘---’ will be displayed instead. (Refer to page 38)

STEREO SOUND MODE

1 Press AUDIO repeatedly during playback to

select between STEREO, L-CH or R-CH.

STEREO - both right and left channels are active

(stereo) L-CH - only left channel is active R-CH - only right channel is active

Note

¡If the Virtual Surround setting is 1 or 2, the sound

mode will be fixed to STEREO, and can not be changed.

1 In stop mode, press MODE twice.

Press PLAY (B) to play the tracks in random order.

PROGRAMME

MP3

This feature allows you to programme a mp3 disc to play in a desired sequence.

1 Press MODE during playback is stopped.

The PROGRAM screen will appear.

2 Press Arrow (K/L) to select a track, then

press ENTER, to save it in a programme.

Press CLEAR/C.RESET to erase the incorrect input.

Press PLAY ( B) to start programmed play

back.

AUDIO LANGUAGE

DVD

The DVD/VCR allows you to select a language during DVD disc (if multi language available) playback.

1 Press AUDIO during playback.

2 Press AUDIO repeatedly to select your

desired language.

Notes

¡Pressing AUDIO may not work on some DVDs with

multiple audio languages (e.g. DVDs which allow audio language setting on the disc menu).

SUBTITLE LANGUAGE

DVD

The DVD allows you to select a language for subtitles during DVD disc (if available) playback.

1 Press SUBTITLE during playback.

2 Press SUBTITLE repeatedly to select your

desired subtitle language.

The subtitle language will be displayed on the dis-

play bar at the top of the screen.

3 To turn off subtitles, press SUBTITLE

repeatedly until OFF appears.

Notes

¡Some discs allow subtitle language setting on the

disc menu. (Operation varies between discs, so refer to the manual accompanying the disc.)

¡If the desired language is not shown after pressing

SUBTITLE several times, the disc does not have subtitles in that language.

¡If you choose a Language that has a 3 letter language

code, the code will be displayed every time you change the Subtitle language setting. If you choose any other languages, ‘---’ will be displayed instead. (Refer to page 38.)

¡ It may take time to display the subtitles in the

selected language.

–34–

2C15

Page 35

CAMERA ANGLE

9/49 0:00:00 -0:00:00

PARENTAL

RATING LEVEL ALL

PARENTAL CONTROL

DVD

Some DVD discs contain scenes which have been shot simultaneously from various angles. You can change the camera angle when the ( ) mark appears on the screen.

1 Press ANGLE during playback.

The selected angle will be displayed on the display bar at the top of the screen.

2 Press ANGLE repeatedly to select your

desired angle.

CHANGING THE ON SCREEN

DISPLAY

DVD

You can check the information about the current disc by pressing DISPLAY on the remote control.

For DVDs

1 Press DISPLAY during playback to show

current Chapter.

¡The elapsed and remaining

playing time of the current chapter will be displayed.

2 Press DISPLAY again to show current Title.

The elapsed and remaining playing time of the cur-

rent title will be displayed.

3 Press DISPLAY third time.

The BIT RATE and the current repeat setting will be

displayed.

¡If you are playing a dual layered disc, the layer num-

ber will also be displayed (L0: Layer 0 is playing. L1: Layer 1 is playing).

4 Press DISPLAY the fourth time to remove

the display.

For audio CDs

1 Press DISPLAY during playback, the current

Track will be displayed on the TV screen.

The elapsed and remaining playing time of the cur-

rent track will be displayed.

2 Press DISPLAY again to show current Total

Track.

The elapsed and remaining playing time of the cur-

rent total track will be displayed.

3 Press DISPLAY third time to remove the dis-

play.

Parental Control limits the disc viewing that exceed your settings. (with a password or playback will stop.) This feature allows you to prevent discs with Adult content being played back by your children.

RATING LEVEL

Rating Level allows you to set the rating level of your DVD discs. Playback will stop if the disc’s ratings exceed the level you set.

1 Press SETUP in STOP mode.

2 Press Arrow ( B) to select CUSTOM, then

press ENTER.

3 Press Arrow (s/B) to

select PARENTAL, then press ENTER.

4 Enter your four-digit password then press

ENTER.

5 Press Arrow (K/L) to select RATING

LEVEL, then press ENTER.

Press Arrow ( then press ENTER.

K/L

) to select the desired level

7 Press SETUP to exit

Notes

¡When doing this for the first time, enter any 4 digits.

(except for 4737) That number will be used as the password from the second time onward. (in the event you forget the password, see below.)

¡To change the password, press Arrow (K/L) to

select CHANGE, then press ENTER. Enter the fourdigit password, then press ENTER.

¡With some DVDs, it may be difficult to find if they are com-

patible with parental lock. Be sure to check if the parental lock function operates in the way that you have set.

¡Record the password in case you forget it.

IF YOU FORGET THE PASSWORD

1 Press 4, 7, 3, 7 at step 4.

Password will be cleared and parental level will be

set to ALL.

2 Proceed the above Steps 4-6 again.

RATING LEVELS

ALL

All parental lock is cancelled.

Level 8

DVD software of any grade (adult/general/children) can be played back.

Levels 7 to 2

Only DVD software intended for general use and children can be played back.

Level 1

Only DVD software intended for children can be played back, with those intended for adult and general use prohibited.

–35–

DVD

2C15

Page 36

DVD SETUP

OFF

DISPLAY

TV ASPECT

4:3 L- BOX ANGLE MARK ON AUTO POWER OFF ON LOGO ON

AUDIO SETTINGS

Choose the appropriate Audio settings for your equipment as it only affect during the playback of DVD discs.

1 Press SETUP in STOP mode.

2 Press Arrow ( B) to select CUSTOM, then

press ENTER.

CUSTOM mode will appear.

Press Arrow (s/ B) to select AUDIO, then press ENTER to confirm.

4 Press Arrow (K/L) to select the below

items, then press ENTER.

DRC (Dynamic Range Control):

¡To compress the range of sound volume. ¡The default setting is OFF. ¡This function is effective only for the sound record-

ed by Dolby Digital recording.

Dolby Digital:

QUICK

Set to BITSTREAM when the unit is connected to a Dolby Digital Decoder. (BITSTREAM: Output by Dolby Digital) (PCM: Convert the Dolby Digital to PCM)

¡The default setting is BITSTREAM.

DTS

Set to BITSTREAM when the unit is connected to DTS Decoder.

¡The default setting is OFF.

DOWN SAMPLING:

¡Set to ON when outputting in 48 kHz. ¡The default setting is ON.

When playing disc with copyright Protection

¡If you select OFF, copyright protection will be acti-

vated and sound will be down sampled at 48kHz.

MPEG:

BITSTREAM : Output by MPEG sound PCM : Convert the MPEG to PCM

¡S

et to

BITSTREAM

when the unit is connected to

MPEG Decoder.

¡The default setting is PCM.

5 Press SETUP to exit.

AUDIO DRC OFF DOLBY DIGITAL BITSTREAM DTS OFF DOWN SAMPLING ON MPEG PCM

VIRTUAL SURROUND

DVD

You can enjoy stereophonic Virtual Surround Effects from your existing stereo system.

1 Press SURROUND

during playback.

2 Press SURROUND to set it 1 (Natural effect)

or 2 (Emphasised effect) or OFF.

3 Press MODE or RETURN to exit.

Note (for CD play only)

¡Virtual Surround will not be effective if the sound

mode is set to something other than STEREO.

¡Turn down the level or turn it “OFF” if the sound is

distorted.

MP3CD

DISPLAY SETTING

DVD

You can change certain aspects of the DVD display screens, On screen messages and the display panel on the front of the DVD/VCR.

1 Press SETUP in STOP mode.

2 Press Arrow ( B) to select CUSTOM, then

press ENTER.

CUSTOM mode will appear.

3 Press Arrow (s/ B) to

select DISPLAY, then press ENTER to confirm.

4 Press Arrow (K/L) to select the below

items, then press ENTER.

–36–

2C15

Page 37

TV ASPECT:

LANGUAGE AUDIO ORIGINAL SUBTITLE OFF DISC MENU ENGLISH PLAYER MENU ENGLISH

¡Press Arrow (K/L) for an item selection, then

QUICK

press ENTER.

¡Select 4:3 LETTER BOX for a black bars appears

on top and bottom of the screen.

¡Select 4:3 PAN - SCAN for a full height picture

with both sides trimmed.

¡Select 16:9 WIDE if a wide-screen TV is connected

to the DVD/VCR.

¡The default setting is 4:3 LETTER BOX.

ANGLE MARK:

¡Press ENTER repeatedly to turn Angle mark ON or

OFF.

¡The default setting is ON.

AUTO POWER OFF:

¡Press ENTER repeatedly to turn Auto Power off ON

or OFF.

¡The default setting is ON and it will turn the

DVD/VCR to off automatically after 35 minutes of no use.

LOGO:

¡Press ENTER to switch ON (opening picture)/

OFF(black).

¡The default setting is ON.

5 Press SETUP to exit.

LANGUAGE SETTING

DVD

Language options are not available with some discs.

1 Press SETUP in STOP mode.

2 Press Arrow ( B) to select CUSTOM, then

press ENTER.

CUSTOM mode will appear.

3 Press Arrow (s/ B) to

select LANGUAGE, then press ENTER to confirm.

4 Press Arrow (K/L) to select the below

items, then press ENTER.

If you want to return to LANGUAGE SETTING

MENU, press Arrow(s ).

AUDIO:

¡Sets the audio language.

SUBTITLE:

¡Sets the subtitle language.

DISC MENU:

¡Sets the language for DVD menu.

PLAYER MENU:

¡Sets the language for the On screen display.

QUICK

5 Press Arrow (K/L) to select a setting, then

press ENTER.

If OTHERS is selected on the AUDIO, SUBTITLE

or DISC MENU screen, press four-digit number to enter the code for the desired language. (Refer to the language code list below.)

¡Only the languages supported by the disc can be

selected.

6 Press SETUP to exit.

Note

¡Language Setting for Audio and Subtitle is not avail-

able with some discs. Then use the AUDIO and the SUBTITLE button. Details are on page 34.

–37–

2C15

Page 38

Langua

Abkhazian 4748 Afar 4747 Afrikaans 4752 Albanian 6563 Amharic 4759 Arabic 4764 Armenian 5471 Assamese 4765 Aymara 4771 Azerbaijani 4772 Bashkir 4847 Basque 5167 Bengali;Bangla 4860 Bhutani 5072 Bihari 4854 Bislama 4855 Breton 4864 Bulgarian 4853 Burmese 5971 Byelorussian 4851

Cambodian 5759 Catalan 4947 Chinese [CHI] 7254 Corsican 4961 Croatian 5464 Czech 4965 Danish [DAN] 5047 Dutch [DUT] 6058 English [ENG] 5160 Esperanto 5161 Estonian 5166

Faroese 5261 Fiji 5256 Finnish [FIN] 5255

ge Code Language Code Languag e Code Language Code

A-B

C-E

F-H

French [FRE] 5264 Frisian 5271 Galician 5358 Georgian 5747 German [GER] 5051 Greek [GRE] 5158 Greenlandic 5758 Guarani 5360 Gujarati 5367 Hausa 5447 Hebrew 5569 Hindi 5455 Hungarian [HUN] 5467

I-K

Icelandic [ICE] 5565 Indonesian 5560 Interlingua 5547 Interlingue 5551 Inupiak 5557 Irish [IRI] 5347 Italian [ITA] 5566 Japanese [JPN] 5647 Javanese 5669 Kannada 5760 Kashmiri 5765 Kazakh 5757 Kinyarwanda 6469 Kirghiz 5771 Kirundi 6460 Korean [KOR] 5761 Kurdish 5767

L-N

Laothian 5861 Latin 5847 Latvian;Lettish 5868 Lingala 5860 Lithuanian 5866

Macedonian 5957 Malagasy 5953 Malay 5965 Malayalam 5958 Maltese 5966 Maori 5955 Marathi 5964 Moldavian 5961 Mongolian 5960 Nauru 6047 Nepali 6051 Norwegian [NOR] 6061

O-R

Occitan 6149 Oriya 6164 Oromo(Afan) 6159 Panjabi 6247 Pashto;Pushto 6265 Persian 5247 Polish 6258 Portuguese [POR] 6266 Quechua 6367 Rhaeto-Romance 6459 Romanian [RUM] 6461 Russian [RUS] 6467

Samoan 6559 Sangho 6553 Sanskrit 6547 Scots Gaelic 5350 Serbian 6564 Serbo-Croatian 6554 Sesotho 6566 Setswana 6660 Shona 6560 Sindhi 6550 Singhalese 6555

Siswat 6565 Slovak 6557 Slovenian 6558 Somali 6561 Spanish [SPA] 5165 Sundanese 6567 Swahili 6569 Swedish [SWE] 6568

Tagalog 6658 Tajik 6653 Tamil 6647 Tatar 6666 Telugu 6651 Thai 6654 Tibetan 4861 Tigrinya 6655 Tonga 6661 Tsonga 6665 Turkish [TUR] 6664 Turkmen 6657 Twi 6669

U-Z

Ukrainian 6757 Urdu 6764 Uzbek 6772 Vietnamese 6855 Volapuk 6861 Welsh 4971 Wolof 6961 Xhosa 7054 Yiddish 5655 Yoruba 7161 Zulu 7267

If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language setting on page 34. If you choose any other languages, ‘---’ will be displayed instead. (3 letter language code is written in bracket.)

–38–

2C15

Page 39

TROUBLESHOOTING GUIDE

If the DVD/VCR does not perform properly when operated as instructed in this Owner's Manual, check the DVD/VCR consulting the following checklist.

D V D

V C R

D V D

PROBLEM CORRECTIVE ACTION

No power. • Make sure the power plug is connected to an AC outlet.

The DVD/VCR does not respond • Check if the power plug is connected to an AC outlet. to the remote control. • Check the batteries in the remote control.

Timer recording is impossible. • Make sure the timer recording is set correctly.

Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.

Playback picture is partially noisy Cannot view a tape but the • Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .

audio is OK No, or poor, playback picture. • See you TV if the video channel is selected.

TV programs cannot be seen • Press VCR. normally.

Video or color fades in and out • when making a copy of a video tape.

Cannot remove the tape. • Check if the DVD/VCR is in the VCR mode. If not, press VCR on the remote control to switch the

No picture. • Connect the video cables firmly.

Disc cannot be played

No sound

Distorted picture

Audio or subtitle language • does not match the set up.

The camera angle cannot be • changed.

Audio or subtitle language • The DVD disc does not contain audio source or subtitles in the selected language. cannot be changed.

“Prohibited icon” appears on the • That operation is prohibited by the DVD/VCR or the disc. screen, prohibiting an operation.

No DTS audio at analogue output

. • Insert the disc.

. • Connect the audio cables firmly.

. • Connect the DVD/VCR directly to the TV.

• Make sure the power is turned on.

• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles

between the sensor and the remote.

• You have to be within 7m of the DVD/VCR.

• Check if the correct mode is selected. If not switch the mode by pressing DVD or VCR,

whichever you need, on the remote control.

• Check if a cassette tape is in the VCR.

• Make sure the DVD/VCR clock is set correctly.

• Put the DVD/VCR in VCR mode. Press VCR on the remote control so that the green VCR OUT-

PUT light is lit.

• Adjust tracking control for a better picture by pressing PROG (o/p) on the DVD/VCR.

• Make sure the DVD/VCR is not in the Menu mode.

• Fine tune your TV.

• Press VCR on the remote control to put it in the VCR mode. Check if the green VCR OUTPUT

light is lit. Then, set it to the TV position by pressing VCR/TV.

You cannot copy a copyrighted video tape. You are experiencing copy guard protection.

mode.

• Insert a correct video disc that plays on this DVD/VCR.

• Press DVD on the remote control. Check if the DVD OUTPUT Light is lit. Then try other DVD

feature.

• Check if the progressive switch is set correctly according to your TV.

• Clean the disc.

• Place the disc correctly, with the label side up.

• Cancel the parental lock or change the rating level.

• Turn the power of the audio component on.

• Correct the audio output settings.

• Correct the input settings on the audio component.

•

There are some cases where pictures may be slightly distorted, which are not a sign of a malfunction.

• Although pictures may stop for a moment, this is not a malfunction. The selected language is not available for audio or subtitles on the DVD disc.

This is not a malfunction

The DVD disc does not

This is not a malfunction

This is not a malfunction.

• Use a DIGITAL AUDIO OUTPUT jack when outputting the DTS audio.

contain sequences recorded from different camera angles.

Notes

Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual for details on correct operations.

¡Playback from a desired track and random playback are not available during programme playback.

–39–

2C15

Page 40

MAINTENANCE

RecordableRecordable

ReWritableReWritable

SERVICING

¡Should your DVD/VCR become inoperative, do not

try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power cord, and please contact the Hitachi dealer who supplied the product or call the Hitachi helpline to locate an Authorized Service Center.

CLEANING THE CABINET

¡Use a soft cloth slightly moistened with a mild deter-

gent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives.

CLEANING DISCS

¡When a disc becomes dirty, clean it with a cleaning

cloth. Wipe the disc from the center out. Do not wipe in a circular motion.

¡Do not use solvents such as benzine, thinner, com-

mercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records.

CLEANING THE DISC LENS

¡If the DVD/VCR still does not perform properly

when it is operated while referring to the relevant sections and to “TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

AUTO HEAD CLEANING

• Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.

• Playback picture may become blurred or interrupted while the TV programme reception is clear. Dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in your DVD/VCR may need to be cleaned.

1. Please visit your local Audio/Video store and purchase a good

quality VHS Video Head Cleaner.

2. If a Video Head Cleaner does not solve the problem, consult our

nearest Authorized Service Center.

NOTES:

• Remember to read the instructions included with the video head cleaner before use.

• Clean video heads only when problems occur.

DISC HANDLING

¡Use discs which have the following logos on them.

(Optical audio digital discs.)

¡Handle the discs so that fingerprints and dust do not

adhere to the surfaces of the discs.

¡Always store the disc in its protective case when it is

not used.

Make your contribution to the environment!!!

• Used up batteries do not belong in the dust bin.

• You can dispose of them at a collection point for used up batteries or special waste.

Contact your council for details.

¡To clean-off, use a soft cloth.

¡Do not use a hard cloth since this will mar the disc.

¡Wipe the disc in a straight line from center to edge.

¡Never wipe with a circular motion.

¡Do not use detergent or abrasive cleaning agents.

–40–

2C15

Page 41

SPECIFICATIONS

Product type: DVD/VCR Combo (DVD player with Video Cassette Recorder)

Discs: DVD video

Audio CD Video Cassette tape

Converter output: UHF Channel 22 ~ 69

Power source: 220 - 240 V ~ +/- 10%, 50 Hz +/- 0.5%

Power consumption: 30 W (standby: 9.0 W)

Operating temperature: 41°F(5°C) to 104°(F40°C)

Dimensions: W 17-1/8” (435 mm)

H 3-7/8” (99 mm)

D 8-9/16” (218 mm)

Weight: 8.4 lbs (3.8 kg)

¡Designs and specifications are subject to change without notice.

–41–

2C15

Page 42

Replace the whole set of batteries at one time, taking care not to mix old and new batteries or batteries of different types, since this can result in leakage or in extreme cases, fire or even an explosion.

Take care to fit your batteries correctly, observing the plus and minus marks on the battery and appliance. Incorrect fitting can cause leakage or in extreme cases, fire or even an explosion.

BATTERY

SAFETY

GUIDELINES

ALWAYS ALWAYS

PLEASE PHOTOCOPY AND DISPLAY

ALWAYS ALWAYS NEVER

NEVER ALWAYS NEVER

ALWAYS ALWAYS ALWAYS

Used correctly, domestic batteries are a safe and dependable source of portable power. Problems can occur if they are misused or abused — resulting in leakage or, in extreme cases, fire or explosion. Here are some simple guidelines to safe battery use designed to eliminate any such problems.

Store unused batteries in their packaging and away from metal objects which may cause a shortcircuit resulting in leakage or, in extreme cases, fire or even an explosion.

Remove dead batteries from equipment and all batteries from equipment you know you are not going to use for a long time. Otherwise the batteries may leak and cause damage.

Never dispose of batteries in fire as this can cause them to explode. Please put dead batteries in with the normal household waste.

Never attempt to recharge ordinary batteries, either in a charger or by applying heat to them. They may leak cause fire or even explode. There are special rechargeable batteries which are clearly marked as such.

Supervise children if they are replacing batteries themselves in order to ensure these guidelines are followed.

Remember that small button cell batteries such as used in some hearing aids, toys, games and other appliances, are easily swallowed by young children and this can be dangerous.

Seek medical advice if you believe a cell has been swallowed.

Make sure battery compartments are secure.

Keep loose button cells away from young children.

–42–

2C15

Page 43

SUBSIDIARY INFORMATION

SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT

This equipment has been designed and manufactured to meet international safety standards but like any elec-

trical equipment, care must be taken if you are to obtain the best results and safety is to be assured.

★★★★★★★★★★★

DO read the operating instructions before you attempt to use the equipment.

DO ensure that all electrical connections (including the mains plug, extension leads and interconnection between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions.

Switch off and withdraw the mains plug when making or changing connections.

DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.

DO be careful with glass panels or doors on equipment.

★★★★★★★★★★★

DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way switch off, withdraw the mains plug and consult your dealer.

DON’T remove any fixed cover as this may expose dangerous voltages.

DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your family know how to do this. Special arrangements may need to be made for infirm or handicapped people.

DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is illegal to watch television whilst driving.

DON’T listen to headphones at high volume, as such use can permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.

Overheating will cause damage and shorten the life of the equipment.

DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fix the manufacturer’s approved stand or legs with the fixings provided according to the instructions.

DON’T allow electrical equipment to be exposed to rain or moisture.

ABOVE ALL

---NEVER let anyone especially children push anything into holes, slots or any other opening in the case — this could result fatal electrical shock:

---NEVER guess or take chances with electrical equipment of any kind.

---it is better to be safe than sorry!

★★★★★★★★★★★

–43–

2C15

Page 44

HITACHI - YOUR GUARANTEE (UK & Ireland)

For the period of 12 MONTHS from the date of purchase your product has the benefit of our FULL PARTS AND LABOUR GUARANTEE as detailed below.

We undertake to replace of repair any part of the product which fails due to a manufacturing defect within 12 months of the date of purchase provided that.

1) The product has been installed and used only in accordance with the instructions supplied with the product.

2) The product has not been repaired maintained, or modified by any person other than our authorised Engineer.

3) The product serial number is not removed or altered.

This guarantee does not apply to products acquired second-hand or for commercial or communal use. This guarantee does not extend to user control adjustments, battery replacement and aerial adjustment. Any parts replaced

under guarantee shall become the property of HITACHI EUROPE LTD. Please note that evidence of the date of purchase will be required before service under guarantee is carried out.

This guarantee does not affect your statutory rights. In all cases of difficulty consult your HITACHI dealer.

HITACHI EUROPE LTD.

Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire SL8 5XF

Tel:01628-643000 Fax:01628-643400 Email:consumer-ser

vice@hitachi-eu.com

www.hitachi-consumer-eu.com

Printed in China

TJ16771

C Hitachi, Ltd. 2003

0VMN03683

H9551BD

★★★★★

Page 45

Hitachi, Ltd. Tokyo, Japan

International Sales Division

THE HITACHI ATAGO BUILDING,

No. 15 –12 Nishi Shinbashi, 2 – Chome,

Minato – Ku, Tokyo 105-8430, Japan.

HITACHI EUROPE LTD,

Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA

UNITED KINGDOM

Tel: 01628 643000 Fax: 01628 643400 Email: consumer-service@hitachi-eu.com

HITACHI EUROPE GmbH

Munich Office Dornacher Strasse 3 D-85622 Feldkirchen bei München

GERMANY

Tel: +49-89-991 80-0 Fax: +49-89-991 80-224 Hotline: +49-180-551 25 51 (12ct/min) Email: HSE- DUS.service@hitachi-eu.com

HITACHI EUROPE srl

Via Tommaso Gulli N.39, 20147 Milano, Italia

ITALY

Tel: +39 02 487861 Tel: +39 02 38073415 Servizio Clienti Fax: +39 02 48786381/2

Email: customerservice.italy@hitachi-eu.com

HITACHI EUROPE S.A.S

Lyon Office B.P. 45, 69671 BRON CEDEX FRANCE Tel: 04 72 14 29 70 Fax: 04 72 14 29 99 Email: france.consommateur@hitachi-eu.com

HITACH EUROPE AB

Egebækgård Egebækvej 98 DK-2850 Nærum

DENMARK

Tel: +45 43 43 6050 Fax: +45 43 60 51 Email: csgnor@hitachi-eu.com

Hitachi Europe Ltd

Bergensesteenweg 421 1600 Sint- Pieters-Leeuw

BELGIUM

Tel: +32 2 363 99 01 Fax: +32 2 363 99 00 Email: sofie.van.bom@hitachi-eu.com

www.hitachidigitalmedia.com

Tel: 03 35022111

HITACHI EUROPE S.A.

364 Kifissias Ave. & 1, Delfon Str. 152 33 Chalandri Athens

GREECE

Tel: 1-6837200 Fax: 1-6835964 Email: service.hellas@hitachi-eu.com

HITACHI EUROPE S.A.

Gran Via Carlos III, 101- 1 08028 Barcelona

SPAIN

Tel: 93 409 2550 Fax: 93 491 3513 Email: atencion.cliente@hitachi-eu.com

HITACHI Europe AB Box 77 S-164 94 Kista

SWEDEN

Tel: +46 (0) 8 562 711 00 Fax: +46 (0) 8 562 711 13 Email: csgswe@hitachi-eu.com

HITACHI EUROPE LTD (Norway) AB STRANDVEIEN 18 1366 Lysaker NORWAY Tel: 67 5190 30 Fax: 67 5190 32 Email: csgnor@hitachi-eu.com

HITACHI EUROPE AB

Neopoli / Niemenkatu 73 FIN-15140 Lahti

FINLAND

Tel : +358 3 8858 271 Fax: +358 3 8858 272 Email: csgnor@hitachi-eu.com

HITACHI EUROPE LTD

Na Sychrove 975/8 101 27 Praha 10 – Bohdalec

CZECH REPUBLIC

Tel: +420 267 212 383 Fax: +420 267 212 385 Email: csgnor@hitachi-eu.com

Hitachi DVPF3EUK User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual