IBM storage products
ibm
Quick installation guide
IBM Microdrive™
CF+ Type II
Models: DMDM-10340
DMDM-10170
Handling precautions
Follow these suggestions to optimize the use of your IBM Microdrive, as well as those devices in which it is installed:
ŸDo not cover the breather hole! Covering the breather hole may result in loss of data.
ŸDo not press on the drive! Do not apply any force to the drive during handling or installation.
ŸAlways handle the drive with care to prevent damage from shock, vibration, or electrostatic discharge (ESD).
ŸHandle the drive carefully by the edges. Do not touch any exposed printed circuit board.
ŸDo not write on the label or remove it. Do not apply additional labels.
ŸAlways carry the drive in its plastic case.
ŸDo not drop the drive.
ŸDo not expose the drive to wet conditions.
ŸDo not place the drive near a strong magnetic field.
ŸDo not expose the drive to extreme temperatures.
ŸDo not use the drive in CF+TM Type II slots without an ejection mechanism.
ŸThe Microdrive may become hot during operation. Be careful when removing the drive from the host device immediately after operation.
Quick installation procedure
Note: Back up all data before beginning installation!
Refer to the manual that came with your computer, camera, or other device to determine if it is compatible with the CF+ Type II or the PC card type II drive/ interface adapter and to find instructions on inserting and removing the IBM microdrive.
Using the IBM Microdrive with a PC card adapter
With a PC card adapter the IBM Microdrive can be installed in devices such as digital cameras or PCs that have a PC card type II slot. If your Microdrive did not come with a PC card, it can be purchased separately.
1.Align the mark of the IBM Microdrive with that of the PC card.
2.Insert the IBM Microdrive firmly into the PC card.
Note: When inserting or removing the PC card, hold the PC card, not the IBM Microdrive.
Using the IBM Microdrive without a PC card adapter
The IBM Microdrive is compatible with the CF+ Type II standard and can be used in devices with the CF+ Type II slot without an adapter card. Refer to the manual shipped with the device to determine its slot type.
If your PC is not recognizing the IBM Microdrive
With the Plug & Play feature of Windows® 98 and 95 your PC should automatically recognize the IBM Microdrive. If it does not do so, do the following:
1.In Windows select Start and Settings.
2.Click Control Panel.
3.Click the Hardware icon, click Next.
4.Select No in the Hardware Wizard, click Next.
5.Select Hard disk controller as the hardware type, click Next.
6.Specify Standard IDE/ESDI hard disk controller
|
Page 1 |
IBM Technology Group Support Center |
version 5.0 |
IBM storage products
Operating systems
The IBM Microdrive has been tested for general compatibility with the following operating systems:
•Windows 98
•Windows 95
•Windows CE
•Apple® OS (refer to the URL below for the applicable operating systems)
Other operating systems may be compatible with the IBM Microdrive but have not been tested.
Product information
The latest product information can be obtained from
http://www.ibm.com/storage/microdrive
including
•Technical tips
•Complete product specifications
•List of compatible devices
ibm®
© International Business Machines Corporation 2000
www.ibm.com/harddrive
IBM Technology Group Support Center
Telephone: 888.426.5214 or 507.286.5825
E-mail: drive@us.ibm.com
Singapore Technology Group Support Center
Telephone: (65)6418.9595 or 1800.418.9595
E-mail: drive@sg.ibm.com
UK Technology Group Support Center
Telephone: 44.1475.898.125
E-mail: drive@uk.ibm.com
Germany Technology Group Support Center
Telephone: 49.7032.153050
E-mail: drive@de.ibm.com
IBM Systems Storage Division
5600 Cottle Road San Jose CA 95193
www.ibm.com/storage
Printed in the United States of America 05-2000
All Rights Reserved
IBM is the registered trademark of International Business Machines Corporation.
Other company, product, and service names may be trademarks or service marks of others.
Produced by the IBM Technology Group Support Center.
OEM Hark Disk Drive Specifications for DMDM-10340/10170, microdrive with CompactFlash Type II, Version 1.0
Product Description data represents IBM’s design objectives and is provided for comparative purposes; actual results may vary based on a variety of factors. This product data does not constitute a warranty. Questions regarding IBM’s warranty terms or methodology used to derive this data should be referred to the IBM Technology Group Support Center. Data subject to change without notice.
Date: 23 May, 2000
|
Page 2 |
IBM Technology Group Support Center |
version 5.0 |