Hitachi DCAA-32880, DCAA-33610, DCAA-34330 Quick installation guide

IBM storage products

Quick installation guide

Deskstar 4

AT/IDE

Models: DCAA-32880, DCAA-33610,
DCAA-34330

8. Save the drive packaging material including the

Handling precautions

1. Do not cover the breather hole! Covering the
breather hole may result in loss of data.

ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it
in the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging.

2. Do not press on the drive! Do not apply any force
to the drive during handling or installation.

3. Always handle the drive with care to prevent dam­age from shock, vibration, or electrostatic discharge
(ESD).

4. Do not open the static-protective bag containing the
drive until required. Static electricity can damage the
drive.

5. Turn off & unplug your computer. Remove cover.

6. When installing the drive, touch a grounded,
unpainted metal surface with the static-protective
package containing the drive for at least two seconds.
(This drains static electricity from the package and
from your body.)

7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.

Power
Connector

AT I/F
Connector

Power
Connector

Logic Card

Back side of drive

JP7

Option Block

JP1

Quick installation procedure

Note: It is advisable to backup all data before
proceeding with the installation.

If your system BIOS cannot handle large capacity
drives (over 540 MB), you may need to use a disk
overlay program such as Ontrack’s Disk Manager.
The following procedure uses the Ontrack Disk
Manager software. Information on obtaining a copy of
Ontrack’s Disk Manager can be found on the Web at
www.ibm.com/harddrive.

Setting the jumpers

1. In a one-drive system, configure your new drive as
Master (Device 0).

2. In a two-drive system, one drive must be
designated as the Master, the other as the Slave
(Device 1).

3. When installing the new drive as a Slave, check the
Master drive to determine if a jumper change is
required to indicate that a Slave drive
is present.

4. Consult your manual to see if your computer
supports Cable Select before choosing this option.

Master active JP1

JP1

1

2

JP2

JP3

JP4

JP511JP6

3

5

7

9

4

6

8

12

10

Slave active JP2

JP7

Cable select JP3
Slave present/

13

Master active JP4 (DCAA)
Reserved JP4 (DAQA)

14

Write cached
disabled JP5
Reserved JP6
Reserved JP7

IBM Hard Disk Drive Technical Support Center version 3.0

Page 1

IBM storage products

Attaching the drive

1. Turn off the computer, unplug the power cord, and
open the case.

2. Match pin 1 of the 40-pin cable to pin 1 of the drive
interface connector. Pin 1 is usually denoted by a
stripe along the edge of the cable.

3. Attach a power plug to either the 3- or 4-pin power
connector.

Mounting the drive

1. Mount the drive securely, using the appropriate
brackets or rails, in any axes, using four 6-32 UNC
metric screws in either bottom or side mounting
holes.

2. The maximum screw insertion depth for the bottom
mounting is 4 mm and for side mounting 4.5 mm.

Configuring your computer

1. If your computer has a plug-in IDE card with a drive

installation procedure, follow the manufacturer’s
instructions.

2. Plug in the power cord and power on your

computer. Your computer may detect a configuration
change and prompt you to proceed to the Setup
screen. If so, proceed to step 4.

3. If your computer does not prompt you to recon-

figure, enter your computer’s Setup, typically by key
selection or keyboard combinations during power-on
or during a reboot. Refer to your computer’s
documentation for the proper key sequence. If the
computer fails to boot up, power off, remove the new
hard drive and return your system to its original con­figuration. Reboot and enter your computer’s Setup.
Follow the directions in step 4, then reattach the new
hard drive.

4. Select “Auto Detect” if your computer Setup sup-

ports this feature. If your computer does not Auto
Detect the drive, select the appropriate UDT (User
Definable Type) for the model being installed.
Then run Disk Manager.

return to your original configuration and contact
technical support.

®

© International Business Machines Corporation 1999

www.ibm.com/harddrive

IBM Hard Disk Drive Technical Support Center

3605 Highway 52 North
Rochester, MN 55901
Telephone: [phone] or 507.286.5825
Fax: 507.253.DRIVE
E-mail: [e-mail]

Singapore Technical Support Center

Telephone: [phone] or 1800.418.9595
E-mail: [e-mail]

IBM Systems Storage Division

5600 Cottle Road
San Jose, CA 95193
www.ibm.com/storage

Printed in the United States of America
01-99
All Rights Reserved
IBM is the registered trademark of International Business Machines Corporation.

Other company, product, and service names may be trademarks or service marks of others.
Produced by the IBM Hard Disk Drive Technical Support Center.
OEM Hard Disk Drive Specifications for DCAA 32880/33610/34330, revision 1.0
Product Description data represents IBM’s design objectives and is provided for com-

parative purposes; actual results may vary based on a variety of factors. This product data
does not constitute a warranty. Questions regarding IBM’s warranty terms or methodology
used to derive this data should be referred to the IBM Hard Disk Drive Technical Support
Center. Data subject to change without notice.

Date: 11 January 1999

number

HeadsCylindersIBM model

/Track

Cap.Sector

2880MB63165,600DCAA-32880
3610MB63167,000DCAA-33610
4330MB63168,400DCAA-34330

Running Disk Manager

1. Insert the Ontrack diskette and reboot your com-

puter.

2. Type DM and press [ENTER] to run Disk Manager.

3. Under “Select an Installation Option” select (E)asy

Disk Installation.

4. Select a drive for installation; Disk Manager will

partition and format the drive.

5. A status dialog will indicate a successful

installation.
If, after complete installation, your system will not

boot up, recheck all settings. If the system still fails to
boot up, remove the new drive from your system to

IBM Hard Disk Drive Technical Support Center version 3.0

Page 2