Hitachi CU-UHD4000-S7 Operating Instructions Manual

Page 1

CAMERA CONTROL UNIT

CU-UHD4000-S7

OPERATING INSTRUCTIONS

Please read these additional Information and operating instructions carefully for proper operation and keep them for future reference.

Additional Information

Page 2

New Functions

The camera control unit CU-UHD4000-S7 has the additional new functions to the standard model by connection with the SK-UHD4000-S7 and CA-UHF4000-S7.

● Two 12G-SDI outputs for 4K signal

●Simultaneous 2K SDR and 4K HDR signal outputs

●Independent 2K DTL function

●BT.2020 matrix function for 4K signal

●HD output signal format display on Color Bars

●Moving Color Bars

●Audio test tones (400Hz & 1000Hz) on Color Bars

●CAM ID SUB display with up to twenty characters on Color Bars

●Return SDI signal with embedded audio can be output at the camera head and be

mixed in the intercom headset

●Optical level of both of the camera head and CCU display on PIX OUT

These New Functions are available with the following version or later version.

CPU software version: V1.00C or later version.

FPGA software version: V4.200 or later version.

Note

SD-SDI outputs are eliminated from the standard model specifications.

Page 3

Facility names and functions (Rear)

4K 12G OUTPUT connectors (BNC)

4K video signal is fed out through single BNC cable.

4K 3G OUTPUT connectors (BNC)

Outputs 4K video signals. Each 4K video is mapped into four 3G-SDI/HD-SDI signals or two 3G-SDI signals.

HD SDI connectors (BNC)

Six (6) sets of HDTV SDI video signals are output.

The MENU and DIAGNOSTIC characters are superimposed on the PIX output. In the table below, the signal outputs are selected via the CCU MENU.

Output Signals

SYSTEM FORMAT

59.94Hz

50.00Hz

29.97Hz

25.00Hz

23.98Hz

4K 3G

OUTPUT

Scanning

2160/59.94p

2160/50p

2160/29.97p

2160/25p

2160/23.98p

Signal

Link

Quad (3Gx4) Quad (3Gx4)

Quad (1.5Gx4)

Dual (3Gx2)

Quad (1.5Gx4)

Dual (3Gx2)

Quad (1.5Gx4)

Dual (3Gx2)

Image

Division

Square Div. or

2-Sample

Interleave Div.

Square Div. or

2-Sample

Interleave Div.

Square Div. or

2-Sample

Interleave Div.

Square Div. or

2-Sample

Interleave Div.

Square Div. or

2-Sample

Interleave Div.

3G-SDI format

Level A or B Level A or B

Level B

(Dual link)

Level B

(Dual link)

Level B

(Dual link)

4K 12G

OUTPUT

Signal 12G-SDI 12G-SDI 6G-SDI 6G-SDI 6G-SDI

OUTPUT

Down-

Convert

1080/59.94p,

1080/59.94i,

720/59.94p,

1080/50p,

1080/50i,

720/50p,

1080/59.94p,

1080/59.94i,

1080/29.97PsF,

720/59.94p,

1080/50p,

1080/50i,

1080/25PsF,

720/50p,

1080/59.94p,

1080/59.94i,

1080/23.98PsF,

720/59.94p,

HD Cut-Out

1080/59.94p,

1080/59.94i

1080/50p,

1080/50i

1080/29.97p 1080/25p 1080/23.98p

Page 4

Facility names and functions (Rear)

4K 12G OUTPUT / 4K 3G signal output combinations

Note-1: To use both 12G output and Quad output simultaneously,

set Image Division to 2-Sample Interleave (2SI) and 3G-SDI Format to Level A (A) in OUTPUT SELECT menu in the CCU.

Note-2: To use both 6G output and Dual/Quad output simultaneously,

set Image Division to 2-Sample Interleave (2SI) and 3G-SDI Format to DUAL in

OUTPUT SELECT menu in the CCU.

Page 5

Function menu

New functions are in the additional menu.

CCU MENU structure

■ＣＵ　ＦＵＮＣＴＩＯＮ　＜＞

　ＢＵＺＺＥＲ　　　　　：ＥＮＡＢＬＥ　ＳＤＩ　ＡＵＤＩＯ　　：ＯＦＦ　　ＣＣＵ　ＩＤ　　　　　：　　１　ＣＡＢＬＥ　ＭＯＤＥ　：ＨＹＢＲＩＤ　ＰＡＲＡ　ＭＯＤＥ　　：ＯＦＦ　ＳＹＳ　ＦＯＲＭＡＴ　＞２１６０ｐ　　　　　　　　　　　　：５９．９４Ｈｚ　ＴＩＭＥ／ＤＡＴＥ：＞１７．１０．３０　　　　　　　　　　　　　　　１２：００　　

■ＯＵＴＰＵＴ　ＳＥＬＥＣＴ　＜＞

　４Ｋ　ＯＵＴＰＵＴ　　：２ＳＩ［Ａ］　４Ｋ　ＣＯＬＯＲ　　　：ＢＴ．７０９　ＨＤ１［１／２］　　　：１０８０ｉ　ＨＤ２［１／２］　　　：１０８０ｉ　ＷＦＭ／ＰＩＸ　　　　：１０８０ｉＨＤ４［１／２］　　　：１０８０ｉ　ＣＵＴ－ＯＵＴ　ＰＯＳＩＴＩＯＮ　　Ｈ　ＰＨＡＳＥ　　　：　　０　　Ｖ　ＰＨＡＳＥ　　　：　　０　ＨＤ　ＦＩＬＴＥＲ：ＭＩＤ　ＬＯＷ

■ＲＥＴＵＲＮ　ＳＥＬＥＣＴ　＜＞

　ＲＥＴ．ＣＨ　　　　　ＳＥＬＥＣＴ　　ＣＨ１　　　　　　　：ＲＥＴ．Ａ１　　ＣＨ２　　　　　　　：ＲＥＴ．Ａ２　　ＣＨ３　　　　　　　：ＲＥＴ．Ａ３　　ＣＨ４　　　　　　　：ＲＥＴ．Ａ４

　ＣＡ　ＨＤ－ＳＤＩ２　：ＲＥＴ．Ｂ１

　ＡＳＳＩＧＮＭＥＮＴ　：＞

■ＭＩＣ　ＧＡＩＮ　＜＞

　ＭＩＣ１　　　　　　　：－６０ｄＢ　ＭＩＣ２　　　　　　　：－６０ｄＢ

　ＭＩＣ　ＲＥＭＯＴＥ　：ＳＴＡＮＤＡＲＤ

■ＳＹＳ　ＦＯＲＭＡＴ　＜

　□５９．９４Ｈｚ　□５０．００Ｈｚ　□２９．９７Ｈｚ　□２５．００Ｈｚ　□２３．９８Ｈｚ

　ＳＥＴ　ＤＡＴＡ　　　：ＰＵＳＨ＜＋＞

■ＡＳＳＩＧＮＭＥＮＴ　＜

　ＳＥＬＥＣＴ　　　　　ＴＹＰＥ　ＲＥＴ　Ａ１　　　　　：１０８０ｉ／ＰｓＦ／Ｐ　ＲＥＴ　Ａ２　　　　　：１０８０ｉ／ＰｓＦ／Ｐ　ＲＥＴ　Ａ３　　　　　：１０８０ｉ／ＰｓＦ／Ｐ　ＲＥＴ　Ａ４　　　　　：１０８０ｉ／ＰｓＦ／Ｐ　ＲＥＴ　Ｂ１　　　　　：１０８０ｉ／ＰｓＦ／Ｐ　ＲＥＴ　Ｂ２　　　　　：１０８０ｉ／ＰｓＦ／Ｐ

■ＫＮＥＥ／ＣＬＩＰ（ＨＤ）　＜

＊ＴＯＴＡＬ　ＫＮＥＥ　：　　２＊Ｒ　ＫＮＥＥ　　　　　：　　０＊Ｂ　ＫＮＥＥ　　　　　：　　０＊ＴＯＴＡＬ　ＳＬＯＰＥ：　１３＊Ｒ　ＳＬＯＰＥ　　　　：　　０＊Ｂ　ＳＬＯＰＥ　　　　：　　０＊ＫＮＥＥ　　　　　　　：ＯＮ

＊ＷＨＩＴＥ　ＣＬＩＰ　：　　０＊ＷＨＩＴＥ　ＣＬＩＰ　：ＯＮ

■ＰＩＸ　ＤＩＳＰＬＡＹ［ＢＡＲＳ］　＜＞

　ＣＡＭ　ＩＤ　　　　　：ＯＮ　ＣＡＭ　ＩＤ　ＳＵＢ　：＞　ＣＣＵ　ＩＤ　　　　　：ＯＮ　ＣＣＵ　ＩＰ　　　　　：ＯＮ　ＳＤＩ　ＦＯＲＭＡＴ　：ＯＮ　ＯＵＴＰＵＴ　　　　　：ＡＬＬ

■ＣＯＬＯＲ　ＢＡＲＳ　＜＞

　ＴＥＳＴ　ＴＯＮＥ　　：ＯＦＦ　　ＭＩＣ１［Ｌ］　　　　：１ＫＨｚ　　ＭＩＣ２［Ｒ］　　　　：１ＫＨｚ　ＭＯＶＩＮＧ　　　　　：ＯＦＦ　　Ｈ　ＳＰＥＥＤ　　　：２　　Ｖ　ＳＰＥＥＤ　　　：２

■ＨＤＲ／ＳＤＲ　＜＞

　４Ｋ　ＯＵＴＰＵＴ　　：ＳＤＲ＊ＨＤ　ＯＵＴＰＵＴ　　：ＳＤＲ　ＨＤＲ　ＳＥＬＥＣＴ　：ＨＬＧ６００

　－ＨＤ　ＳＤＲ－＊ＧＡＩＮ　　　　　　　：　０．０ｄＢ＊ＢＬＡＣＫ　　　　　　：　　　０　ＫＮＥＥ／ＣＬＩＰ　　：＞

■ＳＹＳＴＥＭ　ＴＩＭＩＮＧ　＜＞

　ＧＬ　Ｈ　ＰＨＡＳＥ　：１０８［　１７２８］

■ＰＩＸ　ＤＩＳＰＬＡＹ［ＣＡＭＥＲＡ］　＜＞

　ＮＤ　ＦＩＬＴＥＲ　　：ＯＮ　ＣＣ　ＦＩＬＴＥＲ　　：ＯＮ　ＩＲＩＳ　　　　　　　：ＯＮ　ＣＵＴ　ＯＵＴ　　　　：ＯＦＦ　ＣＡＢＬＥ　ＣＯＮＤ．：ＯＮ［ＧＲＡＰＨ］

■ＴＩＭＥ／ＤＡＴＥ　＜

　ＤＡＴＥ　ＤＩＳＰ　　：ＹＭＤ　ＴＩＭＥ　ＤＩＳＰ　　：ＯＮ　ＹＥＡＲ　　　　　　　：１７　ＭＯＮＴＨ　　　　　　：１０　ＤＡＹ　　　　　　　　：３０　ＨＯＵＲ　　　　　　　：１２　ＭＩＮＵＴＥ　　　　　：３０

　ＳＥＴ　ＤＡＴＡ　　　：ＰＵＳＨ＜＋＞

■ＣＡＭ　ＩＤ　ＳＵＢ　＜

　［ＣＨＡＲＡＣＴＥＲ　ＥＤＩＴ］　　＿

　ＣＨＡＲＡ　ＴＹＰＥ　：ＣＡＰＩＴＡＬ　ＣＨＡＲＡＣＴＥＲ　　：Ａ

　ＳＥＴ　　　　　　　　：ＰＵＳＨ　＞　ＩＮＳＥＲＴ　　　　　：ＰＵＳＨ　＞　ＢＡＣＫ　ＳＰＡＣＥ　：ＰＵＳＨ　＞　ＡＬＬ　ＣＬＥＡＲ　　：ＰＵＳＨ　＜＋＞

■ＨＤ　ＤＴＬ１　＜＞

　ＨＤ　ＤＴＬ　　　　　：ＯＮ　ＬＥＶＥＬ　　　　　　：　　　０　Ｈ　ＧＡＩＮ　　　　　：　－８０　Ｖ　ＧＡＩＮ　　　　　：　－８０　Ｈ　ＣＲＩＳＰ　　　　：－１２０　Ｖ　ＣＬＩＳＰ　　　　：－１２０　ＤＴＬ　ＦＲＥＱ　　　：１７ＭＨｚ　ＬＥＶＥＬ　ＤＥＰ　　：　　　０

■ＨＤ　ＤＴＬ２　＜＞

　ＤＴＬ　ＫＮＥＥ　　　：ＯＮ　　ＷＨＩＴＥ　　　　　：　１１０　　ＢＬＡＣＫ　　　　　：　１１０　ＫＮＥＥ　ＤＴＬ　　　：　　　０　ＳＫＩＮ　ＤＴＬ　　　：ＯＦＦ　　ＣＨ　ＳＥＬＥＣＴ　：ＣＨ１　　ＣＨ１　ＬＥＶＥＬ　：　　　０　　ＣＨ２　ＬＥＶＥＬ　：　　　０　ＳＫＩＮ　ＧＡＴＥ　　：ＯＦＦ　　ＣＨ　ＳＥＬＥＣＴ　：ＣＨ１

■ＬＡＮ　ＳＥＴＴＩＮＧ　＜＞

　ＩＰ　　　　　：１９２．１６８.　　１．　１０　　　ＣＯＮＦ＞：１９２．１６８.　　１．　１０　ＳＵＢＮＥＴ　：２５５．２５５.２５５．　　０　　　ＣＯＮＦ＞：２５５．２５５.２５５．　　０　ＧＡＴＥＷＡＹ：　　０．　　０.　　０．　　０　　　ＣＯＮＦ＞：　　０．　　０.　　０．　　０

　ＳＥＴ　　　　：ＰＵＳＨ　＜＋＞　　　　　　　

■ＩＰ　ＳＥＴＴＩＮＧ　＜

　ＩＰ　　　　　：１９２．１６８.　　１．　１０　　ＳＥＮＤ　　：１９２．１６８.　　１．　１０　ＥＤＩＴ　　ＯＣＴＥＴ１：１９２　　　　　　　２：１６８　　　　　　　３：　　１　　　　　　　４：　１０

　　ＳＥＮＤ　　：ＰＵＳＨ　＜＋＞

■ＳＵＢＮＥＴ　ＳＥＴＴＩＮＧ　＜

　ＳＵＢＮＥＴ　：２５５．２５５.２５５．　　０　　ＳＥＮＤ　　：２５５．２５５.２５５．　　０　ＥＤＩＴ　　ＯＣＴＥＴ１：２５５　　　　　　　２：２５５　　　　　　　３：２５５　　　　　　　４：　　０

　　ＳＥＮＤ　　：ＰＵＳＨ　＜＋＞

■ＧＡＴＥＷＡＹ　ＳＥＴＴＩＮＧ　＜

　ＧＡＴＥＷＡＹ：　　０．　　０.　　０．　　０　　ＳＥＮＤ　　：　　０．　　０.　　０．　　０　ＥＤＩＴ　　ＯＣＴＥＴ１：　　０　　　　　　　２：　　０　　　　　　　３：　　０　　　　　　　４：　　０

　　ＳＥＮＤ　　：ＰＵＳＨ　＜＋＞

The menus marked by the dotted lines are new or have been changed from the standard model.

Page 6

Function menu

1. OUTPUT SELECT menu

■ＯＵＴＰＵＴ　ＳＥＬＥＣＴ　＜＞

　４Ｋ　ＯＵＴＰＵＴ　　：２ＳＩ［Ａ］　４Ｋ　ＣＯＬＯＲ　　　：ＢＴ．７０９　ＨＤ１［１／２］：１０８０ｉ　ＨＤ２［１／２］：１０８０ｉ　ＷＦＭ／ＰＩＸ　　　　：１０８０ｉＨＤ４［１／２］：１０８０ｉ　ＣＵＴ－ＯＵＴ　ＰＯＳＩＴＩＯＮ　　Ｈ　ＰＨＡＳＥ　　　：　　０　　Ｖ　ＰＨＡＳＥ　　　：　　０　ＨＤ　ＦＩＬＴＥＲ　　：ＭＩＤ　ＬＯＷ

Item

Setting

Factory setting

Description

SYS FORMAT

59.94, 50.00

29.97, 25.00,

23.98

59.94, 50.00

29.97, 25.00,

23.98

4K OUTPUT

SQD[B], 2SI[B],

SQD[A], 2SI[A]

SQD[QUAD],

SQD[DUAL],

2SI[DUAL]

2SI[A]

2SI[DUAL]

Assigns output signal of 4K OUTPUT

connector. (*1) SQD: Square division 2SI: 2-Sample Interleave division A/B: SMPTE425M Level-A/B

QUAD/DUAL: Mapping link

4K COLOR

BT.709, BT.2020

BT.709

Sets the color matrix for 4K output only.

HD1[1/2]

1080p, 1080i,

720p,

CUT-OUT[p],

CUT-OUT[i]

1080p, 1080i,

1080PsF, 720p,

CUT-OUT

1080i

Assigns signal of HD1[1/2] connector.

HD2[1/2]

Assigns signal of HD2[1/2] connector.

HD4[1/2]

Assigns signal of HD4[1/2] connector.

WFM/PIX

1080p, 1080i,

720p

1080p, 1080i,

1080PsF, 720p

1080i

Assigns output signal of WFM/PIX connectors.

CUT-OUT

POSITION

Specifies the position of HD screen cut

from 4K screen, when CUT-

OUT signal

is selected on HD1, 2, 4.

H PHASE

-120 to +120

Specifies horizontal phase.

V PHASE

-135 to +135

Specifies vertical phase.

HD FILTER

HIGH, MID HIGH,

MID LOW, LOW

MID LOW

Changes frequency of low-pass filter for

HD down-converter.

2. HDR/SDR menu

■

ＨＤＲ／ＳＤＲ　＜＞

４Ｋ　ＯＵＴＰＵＴ　　：ＳＤＲ＊ＨＤ　ＯＵＴＰＵＴ　　：ＳＤＲ　ＨＤＲ　ＳＥＬＥＣＴ　：ＨＬＧ６００

　－ＨＤ　ＳＤＲ－＊ＧＡＩＮ　　　　　　　：　０．

０ｄＢ＊ＢＬＡＣＫ　　　　　　：　　　０　ＫＮＥＥ／ＣＬＩＰ　　：＞

Item Setting Factory

setting

Description

4K OUTPUT

SDR, HDR

SDR

Sets SDR/ HDR for 4K output.

HD OUTPUT

Note-1

SDR, HDR

SDR

Sets SDR/ HDR for HD output.

HDR SELECT

HLG600,

HLG1200,

HPQ

HLG600

Sets HDR curve.

HD SDR

GAIN

0.0 to -18dB,

0.1 steps

0dB

Adjusts SDR signal level only when

setting simultaneous SDR and HDR

output.

BLACK

-128 to 127

Adjusts BLACK level of SDR signal

only when setting simultaneous SDR and HDR output.

KNEE/CLIP

Moves to KNEE/CLIP (HD) menu.

Note-1 When selecting SDR as the 4K signal output mode, HDR is NOT

AVAILABLE on the HD outputs.

Page 7

Function menu

3. KNEE/CLIP (HD) menu

KNEE/CLIP (HD) menu is enabled only when setting simultaneous SDR and HDR are output.

■ＫＮＥＥ／ＣＬＩＰ（ＨＤ）　＜

＊ＴＯＴＡＬ　ＫＮＥＥ　：　　　２＊Ｒ　ＫＮＥＥ　　　　　：　　　０＊Ｂ　ＫＮＥＥ　　　　　：　　　０＊ＴＯＴＡＬ　ＳＬＯＰＥ：　　１３＊Ｒ　ＳＬＯＰＥ　　　　：　　　０＊Ｂ　ＳＬＯＰＥ　　　　：　　　０＊ＫＮＥＥ　　　　　　　：ＯＮ

＊ＷＨＩＴＥ　ＣＬＩＰ　：　　　０＊ＷＨＩＴＥ　ＣＬＩＰ　：ＯＮ

Item

Setting

Initial

setting

Description

TOTAL KNEE

-128 to +127

Adjusts Total Knee level

R KNEE

-128 to +127

Adjusts R individual channel knee level

B KNEE

-128 to +127

Adjusts B individual channel knee level

TOTAL SLOPE

-128 to +127

Adjusts Total slope level

R SLOPE

-128 to +127

Adjusts R individual channel slope level

B SLOPE

-128 to +127

Adjusts B individual channel slope level

KNEE

ON,OFF

Knee function ON and OFF

WHITE CLIP

-128 to +127

Adjusts White Clip level

WHITE CLIP

ON,OFF

White Clip function ON and OFF

4. SYSTEM TIMING menu

■ＳＹＳＴＥＭ　ＴＩＭＩＮＧ　＜＞

　ＧＬ　Ｈ　ＰＨＡＳＥ　：１０８［１７２８］

Item

Setting

Initial

setting

Description

GL H PHASE

-128(-2048) to +127(2047)

108 (1728)

Adjusts whole system phase against

genlock signal.

3. PIX DISPLAY [CAMERA] menu

■ＰＩＸ　ＤＩＳＰＬＡＹ［ＣＡＭＥＲＡ］　＜＞

　ＮＤ　ＦＩＬＴＥＲ　　：ＯＮ　ＣＣ　ＦＩＬＴＥＲ　　：ＯＮ　ＩＲＩＳ　　　　　　　：ＯＮ　ＣＵＴ　ＯＵＴ　　　　：ＯＦＦ　ＣＡＢＬＥ　ＣＯＮＤ：ＯＮ［ＧＲＡＰＨ］

Item

Setting

Initial

setting

Description

ND FILTER

OFF, ON

Displays ND filter type on PIX OUT.

CC FILTER

OFF, ON

Displays Color Temperature Correction

filter type on PIX OUT.

IRIS

OFF, ON

Displays F-number of lens iris on PIX OUT.

CUT OUT

OFF, WIRE,

CORNER

OFF

Displays marker of CUT-OUT area, when

CUT-OUT signal is selected on HD/SD1,2.

OFF

: No display

WIRE

: Displays the area with rectangle

CORNER

: Displays four corners of the

area

CABLE COND.

OFF

ON[NUMBER], ON[GRAPH]

OFF

Sets the display for the receiving optical

level of both the camera head and CCU.

OFF

: No display

ON[NUMBER]

: Data[0 to 100] display

ON[GRAPH]: Four segments display

　　　ＣＡＭ［■■ ■■］　ＣＣＵ［■■■■］

４．１／６４ＮＤ　Ｂ．３２００Ｋ　　　　Ｆ８．０

CAM &CCU Optical Level

Segment indicator is same as CCU LED optical indicators.

CABLE COND.:ON[GRAPH]

CABLE COND.:ON[NUMBER]

　　　ＣＡＭ［１００］　ＣＣＵ［１００］

４．１／６４ＮＤ　Ｂ．３２００Ｋ　　　　Ｆ８．０

CAM&CCU Optical Level

Page 8

Function menu

4. PIX DISPLAY [BARS] menu

■ＰＩＸ　ＤＩＳＰＬＡＹ［ＢＡＲＳ］　＜＞

Item

Setting

Initial

setting

Description

CAM ID OFF, ON ON Displays Camera ID number on color

bars.

CAM ID SUB

Moves to CAM ID SUB menu.

CCU ID

OFF, ON

Displays CCU ID on color bars.

CCU IP

OFF, ON

Displays CCU IP address on color bars.

SDI FORMAT PFF, ON ON Displays SDI FORMAT information on

color bars.

OUTPUT ALL, PIX ALL

Selects output channels that display CAM ID/CCU ID/CCU IP on color bars.

5. CAMERA ID SUB menu

CAMERA ID SUB with up to twenty characters is set in this menu.

■ＣＡＭ　ＩＤ　ＳＵＢ　＜

　［ＣＨＡＲＡＣＴＥＲ　ＥＤＩＴ］　　＿

　ＣＨＡＲＡ　ＴＹＰＥ　：ＣＡＰＩＴＡＬ　ＣＨＡＲＡＣＴＥＲ　　：Ａ

Item

Setting

Initial

setting

Description

[CHARACTER EDIT]

Moves the cursor by and buttons to edit character.

CHARA TYPE CAPITAL

SMALL NUMBER SYMBOL

CAPITAL Selects a kind of character.

CAPITAL: A to Z SMALL: a to z NUMBER: 0 to 9

SYMBOL: _ ! % ’ [ ] * + , - . / : ; < > ?

CHARCTER

A Selects character by and buttons.

SET

Pushes button to set the character.

INSERT

Moves the cursor to the insert position and then pushes button to insert.

BACK SPACE Pushes button to delete the left

character of the cursor.

ALL CLEAR

Pushes and buttons simultaneously to delete all characters.

PIX OUT display on BAR

Signal Format

CAM ID SUB CAM ID

CCU IP address

　　ＣＡＭ［ ■■■■] 　　ＣＣＵ［■■■■] 　　　　　　　　　　　　　　　１０８０／５９．９４i

ａｂｃｄｅＡＢＣＤＥ０１２３４＿：＊／ーＣＡＭ　ＩＤ：　　１　　　　　ＣＣＵ　ＩＤ：　　　１ＣＣＵ　ＩＰ：１９２．１６８．　　１．　１０

CCU ID

Page 9

Function menu

6. COLOR BARS menu

■ＣＯＬＯＲ　ＢＡＲＳ　＜＞

　ＴＥＳＴ　ＴＯＮＥ　　：ＯＦＦ　　ＭＩＣ１［Ｌ］　　　：１ＫＨｚ　　ＭＩＣ２［Ｒ］　　　：１ＫＨｚ　ＭＯＶＩＮＧ　　　　　：ＯＦＦ　　Ｈ　ＳＰＥＥＤ　　　：２　　Ｖ　ＳＰＥＥＤ　　　：２

Item

Setting

Initial

setting

Description

TEST TONE

OFF, ON

OFF

Audio test tone ON/OFF

MIC1[L]

400Hz, 1KHz

1KHz

Selects the test tone frequency for Lch.

MIC2[R]

400Hz, 1KHz

1KHz

Selects the test tone frequency for Rch.

MOVING

OFF, ON

OFF

Moving color bars ON/OFF

H SPEED -9 to 9 2 Adjusts the horizontal moving speed and

direction

(-): Left, (+): Right

V SPEED -9 to 9 2 Adjusts the vertical moving speed and

direction.

(-): Up, (+): Down

7. HD DTL1

■ＨＤ　ＤＴＬ１　＜＞

　ＨＤ　ＤＴＬ　　　　　：ＯＮ　ＬＥＶＥＬ　　　　　　：　　　０　Ｈ　ＧＡＩＮ　　　　　：　－８０　Ｖ　ＧＡＩＮ　　　　　：　－８０　　Ｈ　ＣＲＩＳＰ　　　　：－１２０　Ｖ　ＣＬＩＳＰ　　　　：－１２０　ＤＴＬ　ＦＲＥＱ　　　：１７ＭＨｚ　ＬＥＶＥＬ　ＤＥＰ　　：　　　０

Item

Setting

Initial

setting

Description

DETAIL

ON,OFF

Detail On and OFF

LEVEL

-128 to +127

Adjusts Detail level

H GAIN

-128 to +127

-80

Adjusts H. detail gain

V GAIN

-128 to +127

-80

Adjusts V. detail gain

H CRISP

-128 to +127

-120

Adjusts H detail crisp

V CRISP

-128 to +127

-120

Adjusts V detail crisp

DTL FREQ

13, 14, 15, 16, 17, 18, 19

17 MHz

Sets the boost frequency of detail.

LEVEL DEP

-128 to +127

Adjusts the level dependent of detail

8. HD DTL2

■ＨＤ　ＤＴＬ２　＜＞

Item

Setting

Initial

setting

Description

DTL KNEE

OFF, ON

DETAIL KNEE ON and OFF

WHITE

-128 to +127

110

Adjusts Positive limit of the detail level

BLACK

-128 to +127

110

Adjusts Negative limit of the detail level

KNEE DTL

-128 to +127

Adjusts the detail level in a highlight knee area.

SKIN DTL

Note-1

ON, OFF

OFF

Skin tone Detail ON and OFF

CH SELECT

CH1,CH2, CH1+2

CH1

Selects CH for skin tone detail

CH1 LEVEL

-128 to +127

Adjusts CH1 skin tone detail level

CH2 LEVEL

-128 to +127

Adjusts CH2 skin tone detail level

SKIN GATE

OFF, ON

OFF

Skin Tone Detail gate ON and OFF

CH SELECT

CH1, CH2

CH1

Selects the skin tone detail area where gate marker is displayed.

Note-1 The HD signal SKIN-TONE DTL detection settings are adjusted in

the CAMERA HEAD MENU.

Page 10

Specifications

■ Input output signals (CU-UHD4000-S7)

Camera Control Unit CU-UHD4000-S7

4K 12G OUTPUT 1/2

12G-SDI or 6G-SDI

・2 Sample Interleave division ・2 channels embedded audio available

･12G-SDI: SMPTE ST 2082-1 ・

6G-SDI: SMPTE ST 2081-1

BNC x2

4K 3G OUTPUT 1/2/3/4

3G-SDI/HD-SDI x4 or 3G-SDI x2

・Square Division or 2 Sample Interleave division ・2 channels embedded audio available

･3G-SDI： SMPTE424/425 Level-A/B ・

HD-SDI: SMPTE292M

BNC x4

HD OUT

HD1(1/2) HD2(1/2) HD4(1/2)

3G-SDI or HD-SDI

・Down-converted (1080p/1080i/1080PsF/720p)

・HD Cut-out (1080p/1080i) ・2 channels embedded audio available ･3G-SDI： SMPTE424/425 Level-A

・

HD-SDI： SMPTE292M

BNC x6

(x2 + x2 + x2)

HD OUT

HD3 (WFM)

3G-SDI or HD-SDI

・Down-converted

(1080p/1080i/1080PsF/720p) ・2 channels embedded audio available ･3G-SDI： SMPTE424/425 Level-A

・

HD-SDI： SMPTE292M

BNC x1

HD OUT

HD3 (PIX)

3G-SDI or HD-SDI

・Down-converted

(1080p/1080i/1080PsF/720p) ・2 channels embedded audio available ･3G-SDI： SMPTE424/425 Level-A

・

HD-SDI： SMPTE292M

BNC x1

RET.A IN (1/2/3/4)

3G-SDI or HD-SDI

(1080p/1080i/1080PsF/ 720p) ･3G-SDI： SMPTE424/425 Level-A

・

HD-SDI： SMPTE292M

BNC x4

RET.B IN (1/2)

3G-SDI or HD-SDI

(1080p/1080i/1080PsF/ 720p) ･3G-SDI： SMPTE424/425 Level-A

・

HD-SDI： SMPTE292M

BNC x2

Page 11

Camera Control Unit CU-UHD4000-S7

MIC OUT 1

0dBm/600Ω

XLR-3pin

MIC OUT 2

0dBm/600Ω

XLR-3pin

INTERCOM (HEAD SET)

0dBu MAX+15dB

XLR-5pin(Female)

Remote 1

1.5Vp-p

4pin

Remote 2

1.5Vp-p

4pin

Remote 3

RJ-45

COMMUNICATION

D-sub 25pin

・

INTERCOM

0dBm , 600Ω at 4Wire 0dBu or -15dBu ,200Ω at 2Wire

TALLY OUT(R/G)

Contact

D-sub 9pin

24Vdc, 10mA

WFM CONTROL

WFM 0-7 0/5V

D-sub 15pin

MIC REMOTE

MIC1,2 Gain

D-sub 15pin

TRUNK

RS-422 (150k baud) (RS-232C : Option)

D-Sub 9 pin