►Before using this product, please read all manuals for this
product. Be sure to read Safety Guide rst. After reading them, store them in a
safe place for future reference.
About this manual
Various symbols are used in this manual. The meanings of these symbols are
described below.
WARNING
CAUTION
NOTICEThis entry notices of fear of causing trouble.
NOTE
• The information in this manual is subject to change without notice.
• The illustrations in this manual are for illustrative purposes. They may differ
slightly from your projector.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
Trademark acknowledgment
• Mac® is a registered trademark of Apple Inc.
• Windows
in the U.S. and/or other countries.
• VESA and DDC are trademarks of the Video Electronics Standard Association.
•
HDMITM, the HDMI logo, and High-Denition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries.
•
Trademark PJLink is a trademark applied for trademark rights in
Japan, the United States of America and other countries and areas.
• Blu-ray DiscTM and Blu-rayTM are trademarks of Blu-ray Disc Association.
• DICOM
for its standards publications relating to digital communications of medical information.
All other trademarks are the properties of their respective owners.
®
®
is the registered trademark of the National Electrical Manufacturers Association
This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect handling.
Please refer to the pages written following this symbol.
, DirectDraw® and Direct3D® are registered trademarks of Microsoft Corporation
1
Contents
Introduction ...............3
Features ......................3
Checking the contents of package
....3
Part names ....................4
Projector, Control panel and Indicators,
Ports, Remote control
Setting up .................7
Arrangement ...................7
Connecting with your devices .....10
Fastening the cables
Fastening the adapter cover ......15
Using the security bar and slot ....15
Connecting to a power supply .....16
Remote control ............17
Installing the batteries ...........17
Using the REMOTE ID function ...17
Changing the frequency of remote control signal
About the remote control signal ...18
Using as a simple PC mouse & keyboard
Status Monitor ............20
Displaying the condition of the projector
. . 20
Displaying the log ..............22
Power on/off ..............24
Turning on the power ...........24
Turning off the power ...........24
Operating ................25
Adjusting the volume of audio output .....25
Temporarily turning off the screen
and audio output
Selecting an input signal .........26
Selecting an aspect ratio .........27
Adjusting the projector's elevator
....28
Adjusting the lens ..............29
Adjusting the zoom and focus,
Adjusting the lens position, Lens memory
Using the automatic adjustment feature
. . 31
Adjusting the position ...........31
Correcting the distortion .........32
Using the magnify feature ........35
Temporarily freezing the screen ...36
Temporarily shading the screen ...36
PbyP (Picture by Picture) /
PinP (Picture in Picture) ...37
Using the menu function .........41
Indication in OSD,
Containing items of each menu
EASY MENU. . . . . . . . . . . . . . . 44
PICTURE menu ............46
IMAGE menu ..............49
INPUT menu ..............52
SETUP menu ..............56
AUDIO menu ..............59
SCREEN menu .............60
OPTION menu .............68
NETWORK menu ...........80
SECURITY menu ...........91
Presentation tools .........98
. . 18
. . 19
Maintenance .............112
Troubleshooting ..........117
. 25
Specications ............129
PC-LESS Presentation ..........98
Thumbnail Mode, Full Screen Mode,
Slideshow Mode, Playlist
USB Display .................108
Starting USB Display, Right-Click menu,
Floating menu, Options window
Replacing the lamp ............ 112
Cleaning and replacing the air lter . 114
Other care ................... 116
Warnings displayed on the Status Monitor
. . 117
Related messages ............ 117
Regarding the indicator lamps ...120
Resetting all settings ...........123
Phenomena that may be easy to
be mistaken for machine defects
. . 124
2
Introduction
Introduction
Features
The projector provides you with the broad use by the following features.
ü The HDMI ports can support various image equipment which have digital
interface to get clearer pictures on a screen.
ü The super bright lamp and high quality optical system can fulll the demands
of professional uses.
ü Some optional lens units and the wide range of the lens shift feature will give
much more chances to install the product wherever you want.
ü The lens shade can hide your inside operations and will help your
presentation.
ü The wealth of I/O ports is believed to support any business scene.
Checking the contents of package
Please see the Contents of package section in the User’s Manual (concise)
which is a book. Your projector should come with the items shown there. Require
of your dealer immediately if any items are missing.
WARNING
to put in the mouth. If swallowed, consult a physician immediately for emergency
treatment.
NOTE
to use the original packing materials when moving the projector. Use special
caution for the lens.
• The projector may make a rattling sound when tilted, moved or shaken, since
a ap to control the air ow inside of the projector has moved. Be aware that
this is not a failure or malfunction.
• Keep the original packing materials, for future reshipment. Be sure
►Keep small parts away from children and pets. Take care not
3
Introduction
Part names
Projector
(1) Lamp cover (
The lamp unit is inside.
(2) Filter cover (114 )
The air lter and intake vent
are inside.
(3) Elevator feet (x2) (28)
(4) Elevator buttons (x2) (28)
(5) Remote sensors (x2) (18, 74)
(6) Lens
(7) Lens cover
(8) Indicators (5)
(9) Intake vents
(10) Control panel (5)
(11) Status Monitor (20)
(12) AC (AC inlet) (16)
(13) Exhaust vents
(14) Ports (5)
(15) Security bar (15)
(16) Security slot (15)
(17) Grip (below)
(18) Safety bar (15)
112 )
(10)
(5)
(3)
(7)
(11)
(12)
(18)
(6)
(16)
(14)
(5)
(15)
(17)
(8)
(13)
(9)
(2)
(4)
(3)
(9)
(4)
(1)
(9)
WARNING
manuals direct it.
►Do not subject the projector to unstable conditions.
►Do not open or remove any portion of the product, unless the
Grip
►Do not apply a shock or pressure to this product. Place
your hands on the grip on the bottom of the projector when
carrying the projector. Remove all the attachments including
the power cord and cables, from the projector when carrying
the projector.
►Do not look into the lens and the openings on the projector while the lamp is
on.
CAUTION
►Do not touch around the lamp cover and the exhaust vents
during use or just after use, since it is too hot.
►Do not attach anything onto the lens except the lens cover of this
projector because it could damage the lens, such as melting the lens.
(3) LAN port
(4) USB TYPE A ports
(5) USB TYPE B port
(6) HDMI 1 port
(7) HDMI 2 port
(8) COMPONENT ports
10 ~ 14)
(G/Y, B/Cb/Pb, R/Cr/Pr, H, V)
(Y,Cb/Pb, Cr/Pr)
(5) (6) (10) (7)
(9) S-VIDEO port
(10) VIDEO port
(11) AUDIO IN1 port
(12) AUDIO IN2 port
(13) AUDIO IN3 (L, R) ports
(14) AUDIO OUT (L, R) ports
(15) MONITOROUT port
(16) REMOTECONTROL IN port
(17) REMOTECONTROL OUT port
(18) CONTROL port
• Any button marked with “*” is not supported on this projector (119).
• Each time you press any button (except ID buttons), the ID button of current
selected ID number will light (
6
17).
Setting up
Setting up
Install the projector according to the environment and manner the projector will be
used in.
For the case of installation in a special state such as ceiling mount, the specied
mounting accessories (
Specications in the User’s Manual (concise)) and
service may be required. Before installing the projector, consult your dealer about
your installation.
Arrangement
Refer to tables T-1 to T-3 at the back of User's Manual (concise) as well as the
following to determine the screen size and projection distance. The values shown
in the table are calculated for a full size screen.
Ⓗ × Ⓥ :
ⓐ :
ⓑ,ⓒ
Screen size
Projection distance
(from the front of the projector unit)
: Screen height
(continued on next page)
Projector top
Projector bottom
7
Setting up
Arrangement (continued)
WARNING
►Install the projector where you can access the power
outlet easily. If an abnormality should occur, unplug the projector urgently.
Otherwise it could cause a re or electric shock.
►Do not subject the projector to unstable conditions. If the projector falls
or topples over, it could result in injury or damage to the projector and the
surrounding things. Using a damaged projector could result in a re and an
electric shock.
• Do not place the projector in unstable places, such as an inclined surface,
places subject to vibration, on top of a wobbly table or cart, or a surface that is
smaller than the projector.
• Do not put the projector on its side, front or rear position.
• Do not attach nor place anything on the projector unless otherwise specied in
the manual.
• Do not use any mounting accessories except the accessories specied by the
manufacturer. Read and keep the manuals of the accessories used.
• For special installation such as ceiling mounting, be sure to consult your dealer
beforehand.
• It is possible to install the projector for any direction with specied mounting
accessories. Consult with your dealer about such a special installation.
• Place your hands on the grip on the bottom of the projector when carrying the
projector. Remove all the attachments including the power cord and cables,
from the projector when carrying the projector.
►Do not install the pro
jector near thermally conductive or ammable
things. Such things when heated by the projector could result in a re and burns.
• Do not place the projector on a metal stand.
►Do not place the projector where any oils, such as cooking or machine oil, are used. Oil may harm the product, resulting in malfunction, or falling from
the mounted position.
►Do not place the projector in a place where it may get wet. Getting the
projector wet or inserting liquid into the projector could cause a re and an
electric shock, and damage the projector.
• Do not place the projector near water, such as in a bathroom, kitchen, or
poolside.
• Do not place the projector outdoors or by the window.
• Do not place anything containing liquid near the projector.
(continued on next page)
8
Arrangement (continued)
Setting up
CAUTION
►Place the projector in a cool place with sufcient ventilation. The projector may shutdown automatically or may malfunction if its
internal temperature is too high.
Using a damaged projector could result in a re and an electric shock.
• Do not place the projector in direct sunlight or near hot objects such as heaters.
• Do not place the projector where the air from an air conditioner or similar unit
will blow on it directly.
• Keep a space of 30 cm or more between a side of the projector and other
objects such as walls.
• Do not place the projector on carpet, cushions or bedding.
• Do not stop up, block nor cover the projector's vent holes. Do not place
anything around the projector that could be sucked in or stuck to the projector's
intake vents.
• Do not place the projector at places that are exposed to magnetic elds, doing
so can cause the cooling fans inside the projector to malfunction.
►Avoid placing the projector in smoky, humid or dusty place. Placing the
projector in such places could cause a re, an electric shock and malfunction of
the projector.
• Do not place the projector near humidiers. Especially for an ultrasonic
humidier, chlorine and minerals contained in tap water are atomized and could
be deposited in the projector causing image degradation or other problems.
• Do not place the projector in a smoking area, kitchen, passageway or by the
window.
NOTICE
• Position the projector to prevent light from directly hitting the
projector's remote sensor.
• Do not place the product in a place where radio interference may be caused.
• Set the ALTITUDE of the SERVICE item in the OPTION menu correctly. It is
recommended to leave it at AUTO usually (
72). If the projector is used with a
wrong setting, it may cause damage to the projector itself or the parts inside.
• Keep heat-sensitive things away from the projector. Otherwise, they may be
damaged by the heat from the projector.
9
Setting up
Connecting with your devices
Before connecting the projector to a device, consult the manual of the device to
conrm that the device is suitable for connecting with this projector and prepare
the required accessories, such as a cable in accord with the signal of the device.
Consult your dealer when the required accessory did not come with the product or
the accessory is damaged.
After making sure that the projector and the devices are turned off, perform
the connection, according to the following instructions. Refer to the gures in
subsequent pages.
Before connecting the projector to a network system, be sure to read Network Guide too.
WARNING
►Use only the appropriate accessories. Otherwise it could
cause a re or damage the projector and devices.
• Use only the accessories specied or recommended by the projector’s
manufacturer. It may be regulated under some standard.
• Neither disassemble nor modify the projector and the accessories.
• Do not use the damaged accessory. Be careful not to damage the accessories.
Route a cable so that it is neither stepped on nor pinched out.
CAUTION
►For a cable with a core at only one end, connect the end
with the core to the projector. That may be required by EMI regulations.
NOTE
• Do not turn on or off the projector while connected to a device in
operation, unless that is directed in the manual of the device. Otherwise it may
cause malfunction in the device or projector.
• The function of some input ports can be selected according to your usage
requirements. Check the reference page indicated beside each port in the
following illustration.
• Be careful not to mistakenly connect a connector to a wrong port. Otherwise it
may cause malfunction in the device or projector.
- When connecting a connector to a port, make sure that the shape of the
connector ts the port.
- Tighten the screws to connect a connector equipped with screws to a port.
- Use the cables with straight plugs, not L-shaped ones, as the input ports of
the projector are recessed.
About Plug-and-Play capability
• Plug-and-Play is a system composed of a computer, its operating system
and peripheral equipment (i.e. display devices). This projector is VESA DDC
2B compatible. Plug-and-Play can be used by connecting this projector to a
computer that is VESA DDC (display data channel) compatible.
- Take advantage of this feature by connecting a computer cable to the
COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.
- Please use the standard drivers in your computer as this projector is a Plug-
and-Play monitor.
(continued on next page)
10
Connecting with your devices (continued)
(
(
26, 108)
26)
59)
(
(
26)
Setting up
Computer
NOTE
• Before connecting the projector to a computer, consult the computer’s
manual and check the compatibility of the signal level, the synchronization
methods and the display resolution output to the projector.
- Some signal may need an adapter to input this projector.
- Some computers have multiple screen display modes that may include some
signals which are not supported by this projector.
- Although the projector can display signals with a resolution up to UXGA
(1600x1200) or up to W-UXGA (1920x1200) for CP-WU8460, the signal will
be converted to the projector’s panel resolution before being displayed. The
best display performance will be achieved if the resolutions of the input signal
and the projector panel are identical.
• If you connect this projector and a notebook computer, you need output the
display to an external monitor, or output simultaneously to the internal display
and an external monitor. Consult the computer's manual for the setting.
• Depending on the input signal, the automatic adjustment function of this
projector may take some time and not function correctly.
- Note that a composite sync signal or sync-on-green signal may confuse the
automatic adjustment function of this projector (54).
- If the automatic adjustment function does not work correctly, you may not see
the dialog to set the display resolution. In such a case, use an external display
device. You may be able to see the dialog and set an appropriate display
resolution.
(continued on next page)
11
Setting up
Connecting with your devices (continued)
External
device
Access
point
80)
(
USB
wireless
adapter
(optional)
80)
(
USB
storage
device
(
98)
WARNING
80)
(
19)
Computer
(
►Heat may build up in the USB wireless adapter, to avoid possible burns disconnect the projector power cord for 10 minutes before touching
the adapter.
►
When using the USB wireless adapter, be sure to connect the adapter to the fur-
ther USB TYPE A port from the LAN port and use the supplied adapter cover (15).
CAUTION
► Before connecting the projector to a network system be sure
to obtain the consent of the administrator of the network.
►
Do not connect the LAN port to any network that might have the excessive voltage.
►
The designated USB wireless adapter that is sold as an option is required to use
the wireless network function of this projector. Before connecting the USB wireless
adapter, turn off the power of the projector and disconnect the power cord. Do not
use any extension cable or device when connecting the adapter to the projector.
►
Before removing the USB storage device from the port of the projector, be sure
to use the REMOVE USB function on the Thumbnail screen to secure your data
(101).
►To connect both the LAN cable and USB device to the projector, use only the
further USB TYPE A port from the LAN port or a LAN cable that is at on the
side where the plug’s wire is visible. Otherwise, both of them cannot be connected correctly, or the wire may break (malfunction).
NOTE
• If an oversized USB storage device blocks the LAN port, use only
the further USB TYPE A port from the LAN port or a USB extension cable to
connect the USB storage device.
(continued on next page)
12
Connecting with your devices (continued)
59)
(
26)
(
(
26)
(
26, 54)
VCR/DVD/
Blu-ray Disc
player
Setting up
TM
NOTE
• The HDMI ports of this model are compatible with HDCP (High-bandwidth Digital Content Protection) and therefore capable of displaying video
signals from HDCP compatible DVD players or the like.
- The HDMI ports support the following signals:
Video signal : 480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60,
1080i@50/60, 1080p@50/60
Audio signal : Format Linear PCM
Sampling frequency 48kHz / 44.1kHz / 32kHz
- This projector can be connected with another equipment that has HDMITM
connector, but with some equipment the projector may not work properly,
something like no video.
- Be sure to use an HDMITM cable that has the HDMITM logo.
- Use a Category 2-certied HDMITM cable to input 1080p@50/60 signal to the
projector.
- When the projector is connected with a device having DVI connector, use a
DVI to HDMITM cable to connect with the HDMITM input.
• The HDMITM cables might come off easily due to the lack of a mechanical lock
on the cables and connectors. It is recommended to fasten the cables to the
projector to prevent the cables from coming off (14).
(continued on next page)
13
Setting up
Connecting with your devices (continued)
Speakers
(with an amplier)
Another
projector
(Wired)
Remote
control
(
58)
Monitor
NOTE
• To use a wired remote control, connect a wired remote control to the
REMOTE CONROL IN port. You can also connect another projector to the
REMOTE CONROL OUT port to control it from the wired remote control. You can utilize this projector as a remote control-relay with the REMOTE CONROL
IN and OUT ports. To connect the wired remote control or another projector
to the REMOTE CONTROL IN or OUT ports, use audio cables with 3.5 mm
diameter stereo mini plugs. This function is useful when a wireless remote
signal may not reliably reach the projector.
Fastening the cables
To get together the signal cables and
prevent them from coming off, fasten them to
the projector using a commercially available
plastic cable tie. Use a cable tie of size
2.0x5.0mm or smaller. It is recommended
to curl the end of the tie slightly before you
thread it to the tie holder to enable it to get
through easily.
WARNING
CAUTION
►Do not bind the power cord.
►Use only a plastic tie to get together or fasten the cables. A
metallic tie may cause damage to the cables and tie holder.
►Do not bind the cables too tightly. The cables or the hole might be damaged.
14
Tie holder
Cable tie
Fastening the adapter cover
Setting up
When using the USB wireless adapter, be
sure to connect the adapter to the further
USB TYPE A port from the LAN port and
use the supplied adapter cover.
Loosen the screw (marked with
1.
triangle) on the bottom left of the
USB TYPE A ports.
Insert the tab of the cover into the
2.
hole at the upper right of the USB TYPE A ports in the direction of the
arrow.
Align the screw holes on the projector and the cover. Then
3.
insert the screw removed from the projector into the hole
and tighten the screw.
WARNING
to put in the mouth.
►Heat may build up in the USB wireless adapter, to avoid possible burns
disconnect the projector power cord for 10 minutes before touching the adapter.
►Keep small parts away from children and pets. Take care not
1
Tab
Security slot
Using the security bar and slot
A commercially available anti-theft chain or
wire can be attached to the security bar on
the projector. Refer to the gure to choose
an anti-theft chain or wire.
Also this product has the security slot for
the Kensington lock.
For details, see the manual of the security
tool.
chain or wire
security bar
11mm
Anti-theft
19mm
15mm
2
3
WARNING
from falling down, since it is not designed for it.
CAUTION
It may become too hot.
NOTE
measures. It is intended to be used as supplemental theft prevention measure.
• The safety bar (4) can be used for the same purpose as the security bar.
• The security bar and slot is not comprehensive theft prevention
►Do not use the security bars and slot to prevent the projector
►Do not place anti-theft chain or wire near the exhaust vents.
15
Setting up
Connecting to a power supply
Put the connector of the power cord into the
1.
AC (AC inlet) of the projector.
Firmly plug the power cord’s plug into the
2.
outlet. In a couple of seconds after the power
supply connection, the POWER indicator will
light up in steady orange.
Please remember that when the DIRECT POWER ON
function activated (69), the connection of the power
supply make the projector turn on.
WARNING
unit is attached to it.
►Please use extra caution when connecting the power cord, as incorrect or
faulty connections may result in re and/or electrical shock.
• Do not touch the power cord with a wet hand.
• Only use the power cord that came with the projector. If it is damaged, consult
your dealer to get a new one. Never modify the power cord.
• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.
• Do not distribute the power supply to multiple devices. Doing so may overload
the outlet and connectors, loosen the connection, or result in re, electric shock
or other accidents.
• Connect the ground terminal for the AC inlet of this unit to the ground terminal
of the building using an appropriate power cord (bundled).
NOTICE
tophase voltage of 220 to 240 V.
►Do not connect the projector to a power supply while no lens
• This product is also designed for IT power systems with a phase-
AC
Power
cord
16
Remote control
Remote control
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote
control starts to malfunction, try to replace the batteries. If you will not use the
remote control for long period, remove the batteries from the remote control and
store them in a safe place.
Holding the hook part of the battery
1.
cover, remove it.
Align and insert the two AA batteries
2.
(HITACHI MAXELL ENERGY, Part No.LR6
or R6P) according to their plus and minus
terminals as indicated in the remote control.
Replace the battery cover in the direction of the arrow
3.
and snap it back into place.
1
2
3
WARNING
directed. Improper use may result in battery explosion, cracking or leakage, which
could result in re, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specied. Do not use batteries of different types at
the same time. Do not mix a new battery with used one.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
• Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing the battery.
►Always handle the batteries with care and use them only as
Using the REMOTE ID function
Utilize this function to control specic projectors by the remote
control assigned the same ID number when you use multiple
projectors of the same type at the same time.
Assign an ID number to each projector before using the
REMOTE ID item in the SERVICE menu of the OPTION
menu (74). Press the ID button with the same ID number
as assigned to the projector you are going to control. The ID
button selected will light for several seconds.
NOTE
current selected ID number will light.
• To conrm the projector's current ID, press any ID button for 3 seconds. Its
number will be shown on each screen regardless of set ID of projector.
• Each time you press any button (except ID buttons), the ID button of
ID buttons
17
Remote control
Changing the frequency of remote control signal
The accessory remote control has the two choices on signal frequency Mode
1:NORMAL and Mode 2:HIGH. If the remote control does not function properly,
attempt to change the signal frequency.
In order to set the Mode, please keep pressing the combination of two buttons
listed below simultaneously for about 3 seconds.
(1) S et to Mode 1:NORMAL
AV MUTE and ZOOM - buttons
(2) S et to Mode 2:HIGH
F5 and KEYSTONE buttons
(2)
F5 button
KEYSTONE
button
(1)
AV MUTE
button
ZOOM -
button
Please remember that the REMOTE
FREQ. in the SERVICE item of the OPTION menu
(74)
of the projector to be
controlled should be set to the same mode as the remote control.
About the remote control signal
The remote control works with the
projector’s remote sensor. This projector
has two remote sensors on the front and
back sides.
The sensors can sense signals within
the following range:
60 degrees (30 degrees to the left and right of the
sensor) within 3 meters about.
30°
30°
3m
30°
30°
(approx.)
3m
NOTE
• You can deactivate one of the sensors using the REMOTE RECEIV.
item in the SERVICE menu of the OPTION menu (74) .
• The remote control signal reected in the screen or the like may be available.
If it is difcult to send the signal to the sensor directly, attempt to make the
signal reect.
• The remote control uses infrared light to send signals to the projector (Class 1
LED), so be sure to use the remote control in an area free from obstacles that
could block the remote control’s signal to the projector.
• The remote control may not work correctly if strong light (such as direct
sun light) or light from an extremely close range (such as from an inverter
uorescent lamp) shines on the remote sensor of the projector. Adjust the
position of projector avoiding those lights.
18
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple
mouse and keyboard of the computer, when the
projector’s USB TYPE B port and the computer’s
type A USB port are connected and MOUSE is
selected for the USB TYPE B item in the OPTION
menu (70).
(1) PAGE UP key: Press PAGE UP button.
(2) PAGE DOWN key: Press PAGE DOWN button.
(3) Mouse left button: Press ENTER button.
(4) Move pointer: Use the cursor buttons
►Improper use of the simple mouse &
keyboard function could damage your equipment.
While using this function, please connect this
product only to a computer. Be sure to check your
(4)
(6)
(5)
computer’s manuals before connecting this product
to the computer.
NOTE
• When the simple mouse & keyboard function of this product does not
work correctly, please check the following.
• When a USB cable connects this projector with a computer having a built-in
pointing device (e.g. track ball) like a laptop PC, open BIOS setup menu, then
select the external mouse and disable the built-in pointing device, because the
built-in pointing device may have priority to this function.
•
Windows 95 OSR 2.1 or higher is required for this function. And also this function may
not work depending on the computer’s con gurations and mouse drivers. This function
can work with the computer which can operate general USB mouse or keyboard.
• You cannot do things like press two buttons at once (for instance, pressing
two buttons at the same time to move the mouse pointer diagonally).
• This function is activated only when the projector is working properly. This
function is not available in any of the following cases:
- While the lamp is warming up. (The POWER indicator blinks in green.)
- When either USB TYPE A or USB TYPE B is selected as the input source.
-
While displaying BLANK (60), TEMPLATE (65) or MY IMAGE (88) screen.
- When any menu is displayed on the screen.
- While using the cursor buttons to operate the sound or screen functions such
as adjusting the sound volume, correcting the keystone, correcting the picture
position and magnifying the screen.
19
Status Monitor
Status Monitor
The Status Monitor is the sub LCD in the rear panel.
Status Monitor
The Status Monitor displays the present condition of
the projector including errors, setup information and
error history.
Displaying the condition of the projector
If no buttons have been operated, the Status Monitor displays as below depending
on the condition of the projector.
NOTE
mode if the STANDBY MODE item of SETUP menu is set to SAVING (
• When INSTALLATION in the SETUP menu is set to FRONT / CEILING or REAR /
CEILING, the contents on the Status Monitor are displayed upside down (
In a normal state
The Status Monitor displays the state of the projector in
three lines.
• The Status Monitor displays nothing while the projector is in standby
1st line
: Displays the condition of the projector.
While the lamp is on, the selected port is
displayed.
Displayed conditions are as below;
STANDBY: The projector is in standby mode.
WARM UP: The projector is warming up.
SEARCHING: The projector is searching an input signal.
COOL DOWN: The projector is cooling down.
58).
57).
S T A N D B Y
#
1 2 3 4 5 6 7 8 0 A B
example
9
2 3 ° C
2nd line
is on. Otherwise, displays the serial number of the projector.
Displayed conditions are as below;
SYNC OUT: Detected input signal is out of specied range.
NO SIGNAL: There is no input signal.
CONNECTED: The projector has connected to the network or the computer
and some image is transferred to the projector while the LAN or USB TYPE B port is selected.
HOLD: The projector has connected to the network but no image is transferred
while the LAN port is selected.
NOT CONNECTED: The projector is not connected to the network or the
computer while the LAN or USB TYPE B port is selected.
(continued on next page)
20
: Displays the condition of the detected input signal while the lamp
Displaying the condition of the projector (continued)
: Displays supplied voltage and peripheral temperature in Celsius
3rd line
while the lamp is on.
Status Monitor
NOTE
are selected in normal condition, nothing is displayed on the 2nd line of the
monitor.
• When the USB TYPE B port is selected even if MOUSE is selected in the
USB TYPE B item of the OPTION menu, "NO SIGNAL" is displayed on the 2nd
line of the monitor (70).
• Displayed temperature might differ from actual peripheral temperature
because the displayed temperature is measured inside of the projector.
In error state
The Status Monitor displays a warning of an error with
larger letters. Resolve the errors referring to the table
of the sections "Related messages" (
"Regarding the indicator lamps" (120 ~122) when the
warning is displayed.
Displayed warnings are as below;
• While the projector is searching an input signal or USB TYPE A ports
117 ~ 119) and
COVER: The lamp cover has not been properly xed.
Refer to the LAMP indicator blinking in the table (
FAN: The cooing fan is not operating.
Refer to the TEMP indicator blinking in the table (
LAMP: The lamp does not light.
Refer to the LAMP indicator lighting in the table (
TEMP: The projector's interior becomes over heated.
Refer to the TEMP indicator lighting in the table (
AIR (AIR FLOW): The internal temperature is rising.
Refer to the description of the message, "CHECK THE AIR FLOW" in the
118 ).
table (
COLD: There is a possibility that the interior portion has become over cooled.
Refer to the LAMP and TEMP indicators alternatively blinking in the table
122).
(
FILTR (FILTER): It is time to clean the air lter.
Refer to the LAMP and TEMP indicators simultaneous blinking in the table
122).
(
120).
121).
120).
121).
ORCEV
example
NOTE
displayed, the backlight blinks at the same time.
• When one of the warnings of FAN, LAMP, COVER, TEMP errors is
21
Status Monitor
Displaying the log
The present setup information and the error history can be displayed on the
Status Monitor with button operation.
NOTE
• When the USB TYPE A port is selected, use the buttons on the control panel
to display the logs. The button operation of the Status Monitor on the remote
control may be unavailable.
• The Status Monitor displays nothing or no button presses for the monitor are
available while the projector is in standby mode if the STANDBY MODE item of
SETUP menu is set to SAVING (58).
•
Both of the Status Monitor and the OSD menu cannot be operated at same time.
When the projector is in a normal condition,
or displays one of the warnings of AIR FLOW,
COLD or FILTER errors, press the FUNCTION
button on the control panel, press the ENTER
button on the remote control for three seconds
or press one of the MY BUTTON buttons if
assigned as STATUS MONITOR. The backlight
of the monitor turns on.
To display the setup information including
usage time
• While the projector is warming up, button presses are ignored.
Use the ◄/► buttons to switch display.
First displayUsage time
Network
information
FUNCTION
button
ENTER
button
Usage time: The Status Monitor displays
the lamp time (usage time of the present
lamp), the lter time (usage time of the air
lter) and the projector usage time.
0 L A M P2 2 5 0 h
F I L T E R 1 2 8 3 5 h
S Y S T E M 2 2 3 8 6 h
Usage time (example)
Lamp time
Filter time
Projector
usage time
Network information: The network information is displayed over three pages.
Use the ▲/▼ buttons to switch the page.
Displayed information in each page is as below;
2nd page
1st page
: Subnet mask
(wireless and wired)
: IP address
I P A DD R E S S
W
1 9 2 1 6 8 0 0 1 9 6
N 1 9 2 1 6 8 0 0 1 0 7 5
2
Wireless
Wired
(wireless and wired)
3rd page
: Default gateway
(wireless and wired)
(continued on next page)
22
Network information
(example)
Displaying the log (continued)
Status Monitor
NOTE
• The Status Monitor and its backlight returns to the rst state before
the FUNCTION or ENTER button was pressed when any button except cursor
buttons is pressed, or after about 30 seconds without button operation.
• The projector usage time is the total lamp time from the projector is
manufactured. It is not reset by using LAMP TIME in the OPTION menu (70).
• If the ▲/▼ buttons are pressed while the usage time is displayed, the usage
time switches to the past one when an error occurred.
To display error history
Log number
Press the ▲ button to display previous error
log. If a warning has been displayed, the
rst previous error log is the present error
currently occurring. The Status Monitor
1 P R E V I O U S
7 F I L T E R E R R O
A C 2 4 0 V3 5 ° C
Error
displays the log number, occurred error, the
supplied voltage and peripheral temperature
Error log (example)
at that time. Press the ► button to display the
usage time when each error occurred.
Use the ▲/▼ buttons to switch the log.
The display switches with the ◄/►
Error log1
Usage time
(error log1)
buttons at each log. Up to 10 error
logs including the present one can be
displayed.
First display
Error log10
Usage time
(current)
Usage time
(error log10)
NOTE
• The Status Monitor and its backlight returns to the rst state before
the FUNCTION or ENTER button was pressed when any button except cursor
buttons is pressed, or after about 30 seconds without button operation.
• If no error or less than 10 errors have occurred, "NO DATA" is displayed in
spite of occurred error in the error log.
23
Power on/off
Power on/off
Turning on the power
Make sure that the power cord is rmly
1.
and correctly connected to the projector
and the outlet.
Make sure that the POWER indicator is
2.
lighted in steady orange (120). Then
remove the lens cover.
Press STANDBY/ON button on the projector
3.
or the ON button on the remote control.
The projection lamp will light up and POWER indicator will begin blinking in
green. When the power is completely on, the indicator will stop blinking and
light in steady green (120).
To display the picture, select an input signal according to the section Selecting an
input signal (26).
POWER indicator
STANDBY button
ON button
STANDBY/ON button
Turning off the power
Press the STANDBY/ON button on the projector or the STANDBY button on
1.
the remote control.
The message “Power off?” will appear on the screen for about 5 seconds.
Press the STANDBY/ON or STANDBY button again while the message
2.
appears.
The projector lamp will go off, and the POWER indicator will begin blinking
in orange. Then the POWER indicator will stop blinking and light in steady
orange when the lamp cooling is complete (120).
Attach the lens cover, after the POWER indicator turns to steady orange.
3.
Do not turn the projector on for about 10 minutes or more after turning it off.
Also, do not turn the projector off shortly after turning it on. Such operations might
cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.
WARNING
Do not look into the lens of the projector or look inside of the projector through
any of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just
after use, since it is too hot.
NOTE
prior to the connected devices.
•
This projector has the function that can make the projector automatically turn on/
off. Please refer to the DIRECT POWER ON
items of the OPTION menu.
24
• Turn the power on/off in right order. Please power on the projector
►A strong light is emitted when the projector’s power is on.
(69)
and AUTO POWER OFF
(69)
Operating
Adjusting the volume of audio output
Use the VOL + / - buttons to adjust the volume.
1.
A dialog will appear on the screen to aid you in
adjusting the volume. If you do not do anything,
the dialog will automatically disappear after a few
seconds.
Operating
VOL + / -
buttons
NOTE
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (59).
• Even if the projector is in the standby mode, the volume is adjustable when
both of the following conditions are true:
- An option other than is selected for AUDIO OUT STANDBY in the AUDIO
SOURCE item of the AUDIO menu (59).
- NORMAL is selected in the STANDBY
When is selected for current picture input port, the volume
•
MODE item of the SETUP menu
(58).
Temporarily turning off the screen and audio output
Press AV MUTE button on the remote control.
1.
The BLANK screen will be displayed instead of
the screen of input signals and the sound from the
AUDIO OUT port will be muted. Please refer to the
BLANK item in SCREEN menu about the BLANK
screen (60).
To exit from the AV MUTE mode and restore the screen and audio, press AV MUTE button again.
NOTE
some control buttons are pressed.
• The projector is not equipped with an internal speaker. The audio is output
from the external audio system connected to the AUDIO OUT port.
is on, use the AV MUTE function above or the lens shade function (36). Taking
any other action may cause the damage on the projector.
• The projector automatically exits from the AV MUTE mode when
CAUTION
►If you wish to have a blank screen while the projector's lamp
AV MUTE
button
25
Operating
Selecting an input signal
Press INPUT button on the projector.
1.
Each time you press the button, the projector
switches its input port from the current port as
below.
COMPUTER IN1 COMPUTER IN2 LAN
VIDEO
S-VIDEO
COMPONENT HDMI 2 HDMI 1
INPUT button
USB TYPE A
USB TYPE B
NOTE
OPTION menu, the input from the ports cannot be selected (68).
• While ON is selected for AUTO SEARCH item in OPTION menu, the projector
will keep checking the ports in above order repeatedly till an input signal is
detected (68).
• It may take several seconds to project the images from the USB TYPE B port.
1.
NOTE
the projector will keep checking every port sequentially till an input signal is
detected (68).
• It may take several seconds to project the images from the USB TYPE B port.
• If you have set SKIP to some ports from SOURCE SKIP in the
Press COMPUTER 1 / 2, LAN, USB TYPE A / B, HDMI 1 / 2, COMPONENT,
S-VIDEO or VIDEO button on the remote control.
The port corresponding to each button is selected as below.
For an input signal from the LAN, USB TYPE A or USB TYPE B ports, or
if there is no signal
CP-X8170: 4:3 (xed)
CP-WX8265, CP-WU8460: 16:10 (xed)
NOTE
• NORMAL mode keeps the original aspect ratio setting.
• ASPECT button does not work when no proper signal is inputted.
27
Operating
Adjusting the projector’s elevator
When the place to put the projector is slightly uneven
to the left or right, use the elevator feet to place the
projector horizontally.
Using the feet can also tilt the projector in order to
project at a suitable angle to the screen, elevating the
front side of the projector within 9 degrees.
This projector has 2 elevator feet and 2 elevator buttons.
An elevator foot is adjustable while pushing the elevator
button on the same side as it.
Holding the projector, push the elevator buttons to
1.
loose the elevator feet.
Position the front side of the projector to the desired
2.
height.
Release the elevator buttons in order to lock the
3.
elevator feet.
After making sure that the elevator feet are locked,
4.
put the projector down gently.
If necessary, the elevator feet can be manually
5.
twisted to make more precise adjustments. Hold the
projector when twisting the feet.
To loose an
elevator foot,
push the elevator
button on the
same side as it.
To nely
adjust, twist
the foot.
CAUTION
projector, since the projector may drop down.
►Do not tilt the projector other than elevating its front within 9 degrees using
the adjuster feet. A tilt of the projector exceeding the restriction could cause
malfunction or shortening the lifetime of consumables, or the projector itself.
It is possible to install the projector for any direction with specied mounting
accessories. Consult with your dealer about such a special installation.
28
►Do not handle the elevator buttons without holding the
Operating
Adjusting the lens
Adjusting the zoom and focus
The ZOOM or FOCUS dialog will appear when you
press any of the buttons from ZOOM, ZOOM -,
ZOOM +, FOCUS + and FOCUS -.
Use the ZOOM + / - buttons on the remote
1.
control or ZOOM button and ◄/► cursor buttons
on the projector to adjust the screen size.
Use the FOCUS + / - buttons to focus the picture.
2.
NOTE
other buttons while the lens is moving.
Adjusting the lens position
Press the LENS SHIFT button. The LENS SHIFT
dialog will appear. Using the ▲/▼/◄/►buttons while
the dialog is displayed shifts the lens. Generally, better
image quality can be got when the lens is set to the
center.
Press the LENS SHIFT button again to exit the
LENS SHIFT function.
CENTERING
Press the ENTER or INPUT button while the dialog is
displayed to execute the CENTERING feature, which
adjusts the lens to the center. A message dialog is displayed for conrmation. Pressing the ►button performs
CENTERING. You can also perform CENTERING in the
standby mode by pressing the FUNCTION and LENS SHIFT buttons on the control panel for 3 seconds at the
same time.
• The projector may ignore operation by
LENS SHIFT button
ZOOM + / - buttons
FOCUS + / - buttons
LENS SHIFT
button
FOCUS - / +
buttons
FUNCTION
button
ZOOM button
CAUTION
►Do not put your ngers or any other things around the lens. The
moving lens could catch them in the space around the lens and result in an injury.
NOTE
hourglass icon will appear on the screen. CENTERING may take some time till the
lens reaches the center.
• The projector may ignore operation by buttons while moving the lens.
• The CENTERING feature while the projector is in the standby mode is disabled if
the STANDBY MODE item of SETUP menu is set to SAVING. Perform CENTERING
before the projector's power is turned off, or set the STANDBY MODE to NORMAL.
• The adjustable range of LENS SHIFT varies depending on the lens unit mounted
on the projector to maintain picture quality. Therefore LENS SHIFT adjustment may
not reach the end of the indicator in the dialog, and that is not a failure.
• While the lens is moving to the center, the menu will disappear and an
29
Operating
Adjusting the lens (continued)
Lens memory
This projector is equipped with memory functions for the
lens adjustments (LENS SHIFT and LENS TYPE). Up
to 3 sets of adjustments can be stored.
To utilize the lens memory feature, press the POSITION
or FUNCTION button while the LENS SHIFT dialog is
displayed. Then the LENS MEMORY dialog will appear. The current lens adjustments are displayed on the
“CURRENT” line. The adjustments already stored in the
lens memory are displayed on the lines of SAVE and
LOAD-1 to 3.
SAVE:
To store the current lens adjustments, select one of the
"SAVE" options numbered 1 to 3 (number of the lens
memory) and press the ►or ENTER button.
Remember that the current data being stored of
a memory will be lost by saving new data into
the memory.
LOAD:
To recall stored adjustments, select one of the
"LOAD" options numbered 1 to 3 (number of the
lens memory) and press the ►or ENTER button.
Remember that the current adjusted condition will be lost by loading data. If you
want to keep the current adjustment, please save it before performing a LOAD
function.
CLEAR LENS MEMORY:
To clear the adjustment stored in a lens memory, select CLEAR LENS MEMORY
and press the ►or ENTER button. The CLEAR LENS MEMORY dialog will be
displayed. Select the number of the lens memory to be cleared using the ▲/▼
buttons and press the ►button. A message dialog is displayed for conrmation.
Press the ►button again to clear the lens memory.
FUNCTION
button
POSITION
button
LENS MEMORY
button
NOTE
• You can perform the LOAD function using LENS MEMORY button.
30
• The projector may ignore operation by buttons while moving the lens.
Using the automatic adjustment feature
Press AUTO button on the remote control.
1.
Pressing this button performs the following.
For a computer signal
The vertical position, the horizontal position and the
horizontal phase will be automatically adjusted.
Make sure that the application window is set to its
maximum size prior to attempting to use this feature. A dark picture may still be
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal and s-video signal
The video format best suited for the respective input signal will be selected
automatically. This function is available only when the AUTO is selected for
53).
the VIDEO FORMAT item in the INPUT menu (
horizontal position will be automatically set to the default.
For a component video signal
The vertical position and horizontal position will be automatically set to the default.
The horizontal phase will be automatically adjusted.
The vertical position and
Operating
AUTO
button
NOTE
please note that it may not function correctly with some input.
• When this function is performed for a video signal, a certain extra such as a line
may appear outside a picture.
• When this function is performed for a computer signal, a black frame may be
displayed on the edge of the screen, depending on the computer model.
The items adjusted by this function may vary when the FINE or DISABLE is selected
•
for the AUTO ADJUST item of the SERVICE item in the OPTION menu (
• The automatic adjustment operation requires approx. 10 seconds. Also
72).
Adjusting the position
Press POSITION button on the remote control when no menu is indicated.
1.
The “POSITION” indication will appear on the screen.
Use the ▲/▼/◄/► cursor buttons to adjust the picture
2.
position.
When you want to reset the operation, press RESET
button on the remote control during the operation.
To complete this operation, press POSITION button again. Even if you do not do
anything, the dialog will automatically disappear after a few seconds.
NOTE
some image such as an extra-line may appear at outside of the picture.
• When this function is performed on a video signal or s-video signal, the range of
this adjustment depends on OVER SCAN in IMAGE menu (
possible to adjust when OVER SCAN is set to 10.
• If POSITION button is pressed when a menu is indicated on screen, the displayed
picture does not move its position but the menu does.
This function is unavailable for a signal from the LAN, USB TYPE A / B or HDMI 1 / 2 port.
•
• When this function is performed on a video signal or an s-video signal,
50) setting. It is not
POSITION
button
31
Operating
Correcting the distortion
To correct the distortion of projected screen, you can select one of three
options, AUTO, MANUAL and PERFECT FIT. First press the KEYSTONE
button to display the KEYSTONE menu, and point at one
of items with the ▲/▼ buttons.
AUTO: performs the automatic vertical keystone
correction. (56)
MANUAL: allows you to adjust the vertical and horizontal
keystone.
PERFECT FIT:
allows you to adjust each of the screen
corners and sides to correct the
distortion.
Then follow the procedure shown below for the item
you selected.
KEYSTONE
button
NOTE
• The menu or dialog will automatically disappear after several seconds
of inactivity. Press the KEYSTONE button again, or point the cursor at EXIT in
the dialog and press the ►or ENTER button to end the operation and close the
menu or dialog.
• When the screen is adjusted by PERFECT FIT, neither AUTO nor MANUAL is
selectable. If you wish to use these functions, refer to step 1 in the PERFECT
FIT item to initialize the adjustment of PERFECT FIT.
• When TRANSITION DETECTOR is ON, these functions are not available
(94).
AUTO:
When AUTO is pointed at, pressing the ► or ENTER button performs automatic
vertical keystone correction.
NOTE
• When the projector is in one of the following conditions, the automatic
vertical keystone correction feature may not work correctly or at all.
- REAR / CEILING or FRONT / CEILING is selected for the INSTALLATION
item in the SETUP menu, and the projector screen is slanted or tilted downwards.
- The ZOOM adjustment is not set to the full WIDE (wide-angle focus).
- The projector is nearly horizontal (about ±4°).
- The projector is inclined at about ±35 degrees or over.
• When the horizontal lens shift is not set to the center, this function may not
work well.
32
Correcting the distortion (continued)
MANUAL:
When MANUAL is pointed at, pressing the ► or
ENTER button displays the KEYSTONE_MANUAL
dialog.
Select the vertical or horizontal keystone ( / )
1.
with the ▲/▼ buttons.
Use the ◄/► buttons to adjust the keystone distortion.
2.
Operating
NOTE
function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.
• When the horizontal lens shift is not set to the center, this function may not
work well.
• Point at RETURN in the dialog with the ▲/▼ buttons and press ◄ or ENTER
button to return to the KEYSTONE menu.
When PERFECT FIT is pointed at, pressing the
► or ENTER button displays the KEYSTONE_
PERFECT FIT dialog.
This projector is equipped with a test pattern for
PERFECT FIT. Select the test pattern icon
shown in the lower left of the dialog with the ◄/▼
buttons. When you press the ENTER or INPUT
button, the test pattern appears or disappears.
1.
with the RESET button, and press the ENTER or
INPUT button.
2.
ENTER or INPUT button. For CP-X8170 and CPWX8265, also the sides can be selected to adjust.
• When the zoom adjustment is set to the TELE (telephoto focus), this
PERFECT FIT:
CP-X8170, CP-WX8265,
If it is necessary to initialize the current
adjustment, point at RESET in the dialog
Select one of the corners to be adjusted
with the ▲/▼/◄/► buttons and press the
(continued on next page)
CP-WU8460
33
Operating
Correcting the distortion (continued)
Adjust the selected part as below.
3.
● For adjusting a corner, use the ▲/▼/◄/► buttons to adjust the position of
the corner.
● <Only for CP-X8170 / CP-WX8265>
For adjusting the upper or lower side, use the ◄/► buttons to select any
one point on the side, and use the ▲/▼ buttons to adjust the distortion of
the side.
● <Only for CP-X8170 / CP-WX8265>
For adjusting the left or right side, use the ▲/▼ buttons to select any one
point on the side, and use the ◄/► buttons to adjust the distortion of the side.
● To adjust another corner or side, press the ENTER or INPUT button and
follow the procedure from step 2.
This projector is equipped with a memory feature for PERFECT FIT
4.
adjustment. Up to 3 sets of adjustments can be stored.
● SAVE:
To store the current PERFECT FIT adjustment, select one of the SAVE
icons
and press the ENTER or INPUT button.
Remember that the current data being stored of a memory will be lost by
saving new data into the memory.
● LOAD:
To recall stored adjustments, select one of the LOAD icons
1 to 3 (number of the memory) with the ◄ /▲/▼ buttons and press the
ENTER or INPUT button.
Remember that the current adjusted condition will be lost by loading data. if
you want to keep the current adjustment, please save it before performing a
LOAD function.
numbered 1 to 3 (number of the memory) with the ◄ /▲/▼ buttons
numbered
NOTE
Each corner and side can be adjusted individually but in some cases it may
be adjusted in conjunction with another corner or side. This is due to control
restrictions and not a malfunction.
• The LOAD functions whose linked memory has no data are skipped.
• There may be some noise and the screen may icker for a moment when
loading data. This is not malfunction.
• Point at RETURN in the dialog with the ▲/▼ buttons and press the ◄ or
ENTER button to return to the KEYSTONE menu.
34
• <Only for CP-X8170 / CP-WX8265>
Using the magnify feature
Press the MAGNIFY ON button on the remote
1.
control.
The picture will be magnied, and the MAGNIFY
dialog will appear on the screen. When the
MAGNIFY ON button is pressed for the rst time
after the projector is turned on, the picture will be
zoomed by 1.5 times. On the dialog, triangle marks
to show each direction will be displayed.
The display magnication of the projector switches in order
2.
with every press of the MAGNIFY ON button.
For computer signals, HDMI
LAN, USB TYPE A or USB TYPE B ports
1.5 times 2 times 3 times 4 times 1 time
TM
(RGB) signals, input signals from the
Operating
MAGNIFY
ON / OFF
buttons
For video signals, s-video signals, component video signals or
While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor
3.
buttons to shift the magnifying area.
Press the MAGNIFY OFF button on the remote control to exit magnication.
4.
NOTE
with no operation. The dialog will appear again if the MAGNIFY ON button is
pressed when the dialog has automatically disappeared.
• The magnication is automatically disabled when the displaying signal or its
display condition is changed.
• While the magnication is active, the keystone distortion condition may vary. It
will be restored when the magnication is disabled.
• Some horizontal stripes might be visible on the image while magnication is
active.
• This function is not available in the following cases:
- A sync signal in the range not supported is input.
- There is no input signal.
TM
HDMI
1.5 times 2 times 1 time
(Component) signals
• The MAGNIFY dialog will automatically disappear in several seconds
35
Operating
Temporarily freezing the screen
Press the FREEZE button on the remote control.
1.
The “FREEZE” indication will appear on the screen
(however, the indication will not appear when the OFF
is selected for the MESSAGE item in the SCREEN
menu (63), and the projector will go into the
FREEZE mode, which the picture is frozen.
To exit the FREEZE mode and restore the screen to normal, press the
FREEZE button again.
FREEZE
button
NOTE
control buttons are pressed.
• If the projector continues projecting a still image for a long time, the LCD
panel might possibly be burned in. Do not leave the projector in the FREEZE
mode for too long.
• Images might appear degraded when this function is operated, but it is not a
malfunction.
• The projector automatically exits from the FREEZE mode when some
Temporarily shading the screen
Press the SHADE button on the control panel.
1.
The mechanical lens shade closes and the
screen turns to black. The SHADE indicator on
the projector blinks in yellow while the shade is
closed.
To open the shade and restore the screen, press
the SHADE button again.
CAUTION
is on, use the lens shade function above or the AV MUTE function (25). Taking
any other action may cause the damage on the projector.
NOTE
SHADE TIMER passes
• When turning off the power by the normal procedure, the lens shade opens
automatically. If AC power supply is disconnected while opening or closing the
lens shade, the moving of the lens shade stops. However, the next time the
projector is turned on, the lens shade opens again automatically.
•
►If you wish to have a blank screen while the projector's lamp
The projector will turn off automatically when the time set up by the
(69)
.
SHADE
button
36
Operating
PbyP (Picture by Picture) / PinP (Picture in Picture)
The PbyP / PinP is a function for displaying two different picture signals on a
screen that is separated into main and sub areas for each signal.
main
area
PinP mode
sub area
PbyP
button
main
ð
area
Normal modePbyP mode
sub
area
ð
Press the PbyP button on the remote control. This acctivates the PbyP mode.
Then, press the PbyP button again. The projector goes into PinP mode. The
screen displayed before the PbyP button was pressed will be displayed as the
main area. Most of operations are effective for the main area only. Only outputs
the audio input signal paired with the picture input signal for the main area.
To quit the PinP mode, press the PbyP button again.
NOTE
• If the LAN or USB TYPE A / B port is selected when the PbyP button
is pressed, input from other port is displayed on the main area.
• When in the PbyP / PinP mode, use the MENU button on the remote control
or ▲/▼ buttons on the control panel to display the OSD menu.
• There are certain functions that cannot be used when in the PbyP / PinP
mode.
• A message will be displayed when buttons that cannot be used are pressed
(119 ). However, note that there are certain unusable buttons for which
messages are not displayed.
• The functions on the OSD menu that cannot be used are displayed in gray
and cannot be selected.
(continued on next page)
37
Operating
PbyP (Picture by Picture) / PinP (Picture in Picture) (continued)
Setting information
The setting information will be appeared for several seconds when the PbyP /
PinP function is started. Displays the input information for each area. A yellow
frame around the main area and an audio mark indicating the audio output will
also be displayed. The information can be redisplayed with the ◄/► buttons after
it has been erased.
Audio mark
main area sub area
Input information
PbyP mode
Changing the main area
Frame
main area
Input information
PinP mode
Audio mark
Frame
sub area
The position of the main area can be toggled with the ◄/► buttons when the
setting information is displayed on the screen. The yellow frame and the audio
mark will move together with it.
main
area
sub
area
PbyP mode
sub
area
main
area
main areasub area
sub area
PinP mode
main area
(continued on next page)
38
Operating
PbyP (Picture by Picture) / PinP (Picture in Picture) (continued)
Changing the picture input signal
Press any button to select an input port on the remote control or press the
INPUT button on the control panel. A dialog box to select the input signal for
the main area will be displayed. Choose a signal using the ▲/▼ buttons. To
change the signal in the sub area, switch temporarily across to the main area
with the ◄/► buttons.
Displaying the same signal on the both areas is not allowed. Refer to the table
for details on available input signal combinations. Any combinations marked
with "X" can not be selected.
Sub area
Main area
COMPUTER IN1
COMPUTER IN2
LAN
USB TYPE A
USB TYPE B
HDMI 1
HDMI 2
COMPONENT
S-VIDEO
VIDEO
main area sub area
Input signal
PbyP mode
COMPUTER IN1
COMPUTER IN2
LAN
USB TYPE A
USB TYPE B
HDMI 1
HDMI 2
COMPONENT
S-VIDEO
X O XXX O O O O O
O XXXX O O O O O
XX XXXXX XXX
XX XXXXX XXX
XX XXXXX XXX
O OX XXX O O O O
O OX XX OX O O O
O OX XX O OX O O
O OX XX O O O XO
O OX XX O O O O X
Input signal
VIDEO
main area
sub area
PinP mode
NOTE
• The combined input signals marked with an "O" can be selected and
displayed in the PbyP / PinP mode even when the port is set to SKIP with the
SOURCE SKIP on the OPTION menu (68).
(continued on next page)
39
Operating
PbyP (Picture by Picture) / PinP (Picture in Picture) (continued)
PbyP / PinP SWAP function
Press the MY BUTTON assigned the PbyP / PinP SWAP (
the both area is exchanged without any setting change.
71). The position of
main
area
NOTE
sub
area
PbyP modePinP mode
sub
area
main
area
main area
sub area
sub area
main area
• For some signals, it may not be displayed correctly in the PbyP / PinP
mode, even if it can be displayed properly in the normal mode.
Changing the size of main area in PbyP mode
Using ▲/▼ buttons on the remote control changes the size of main area in
PbyP mode.
main area
sub area
main area
sub area
main area
sub area
Changing the position of sub area in PinP mode
1. Select PinP POSITION in SCREEN menu (
67).
2. Using ▲/▼ buttons on the remote control changes the position of sub area
in PinP mode.
40
main area
sub area
main area
sub area
main area
sub areasub area
main area
Operating
Using the menu function
This projector has the following menus:
PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK,
SECURITY and EASY MENU.
EASY MENU consists of functions often used, and the other menus are classi ed
into each purpose and brought together as the ADVANCED MENU.
Each of these menus is operated using the same methods. While the projector
is displaying any menu, the MENU button on the projector works as the cursor
buttons. The basic operations of these menus are as follows.
ENTER button
RESET button
ESC button
To start the MENU, press the MENU button. The MENU you last used (EASY
1.
or ADVANCED) will appear. EASY MENU has priority to appear just after
powered on.
In the EASY MENU
2.
(1) Use the ▲/▼ cursor buttons to select an item to
operate. If you want to change it to the ADVANCED
MENU, select the ADVANCED MENU.
(2) Use the ◄/► cursor buttons to operate the item.
In the ADVANCED MENU
(1) Use the ▲/▼ cursor buttons to select a menu.
If you want to change it to the EASY MENU, select
the EASY MENU.
The items in the menu appear on the right side.
(2) Press the ► cursor button or ENTER button to
move the cursor to the right side. Then use the
▲/▼ cursor buttons to select an item to operate and press the ► cursor
button or ENTER button to progress. The operation menu or dialog of the
selected item will appear.
(3) Use the buttons as instructed in the OSD to operate the item.
Cursor buttons
MENU
button
INPUT
button
(continued on next page)
41
Operating
Using the menu function (continued)
To close the MENU, press the MENU button again or select EXIT and press
3.
the ◄ cursor button or ENTER button. Even if you do not do anything, the
dialog will automatically disappear after about 30 seconds.
NOTE
use the cursor buttons after pressing the POSITION
button.
• Some functions cannot be performed when a certain
input port is selected, or when a certain input signal is
displayed.
• When you want to reset the operation, press RESET button on the remote
control during the operation. Note that some items (ex. LANGUAGE, VOLUME)
cannot be reset.
• In the ADVANCED MENU, when you want to return to the previous display,
press the ◄ cursor button or ESC button on the remote control.
• If you want to move the menu position,
POSITION
button
Indication in OSD (On Screen Display)
The meanings of the general words on the OSD are as follows.
IndicationMeaning
EXIT
RETURNSelecting this word returns the menu to the previous menu.
CANCEL or NO
OK or YES
Selecting this word nishes the OSD menu. It's the same as
pressing the MENU button.
Selecting this word cancels the operation in the present
menu and returns to the previous menu.
Selecting this word executes the prepared function or shifts
the menu to the next menu.
42
Using the menu function (continued)
Containing items of each menu
The items contained in the menus are as below;
MenuItems
ASPECT, AUTO KEYSTONE,
PERFECT FIT, PICTURE MODE, ECO MODE, INSTALLATION,
EASY MENU (
PICTURE (
IMAGE (
INPUT (
SETUP (
AUDIO (
SCREEN (
OPTION (
NETWORK (
SECURITY (
44)
RESET, FILTER TIME, LANGUAGE, ADVANCED MENU, EXIT
BRIGHTNESS, CONTRAST, GAMMA, COLOR TEMP,
46)
49)
52)
56)
59)VOLUME, AUDIO SOURCE
60)
68)
COLOR, TINT, SHARPNESS, ACTIVE IRIS, MY MEMORY,
ACCENTUALIZER
ASPECT, OVER SCAN, V POSITION, H POSITION, H PHASE,
H SIZE, AUTO ADJUST EXECUTE
PROGRESSIVE, VIDEO NR, COLOR SPACE, COMPONENT,
VIDEO FORMAT, HDMI FORMAT, HDMI RANGE,
COMPUTER IN, FRAME LOCK, RESOLUTION
AUTOKEYSTONE,
PERFECTFIT, AUTO ECO MODE, ECO MODE, INSTALLATION,
STANDBY MODE, MONITOR OUT
LANGUAGE, MENU POSITION, BLANK, START UP, MyScreen,
MyScreen Lock, MESSAGE, SOURCE NAME, TEMPLATE, C. C.,
PinP POSITION
SOURCE SKIP, AUTO SEARCH, AUTO KEYSTONE,
DIRECT POWER ON, AUTO POWER OFF, SHADE TIMER,
USB TYPE B, LAMP TIME, FILTER TIME, MY BUTTON,
SERVICE
WIRED INFORMATION, PROJECTOR NAME, MY IMAGE,
AMX D. D., PRESENTATION, SERVICE
SECURITY PASSWORD CHANGE, MyScreen PASSWORD,
PIN LOCK, TRANSITION DETECTOR, MY TEXT PASSWORD,
91)
MY TEXT DISPLAY, MY TEXT WRITING,
SECURITY INDICATOR, STACK LOCK
KEYSTONE, KEYSTONE,
Operating
KEYSTONE, KEYSTONE,
43
EASY MENU
EASY MENU
From the EASY MENU, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons. Then
perform it according to the following table.
ItemDescription
ASPECT
AUTO KEYSTONE
KEYSTONE
KEYSTONE
PERFECT FIT
PICTURE MODE
Using the ◄/► buttons switches the mode for aspect ratio.
See the ASPECT item in IMAGE menu (
Using the ► button executes the auto keystone function.
See the AUTO KEYSTONE item in SETUP menu (
Using the ◄/► buttons corrects the vertical keystone distortion.
See the
Using the ◄/► buttons corrects the horizontal keystone distortion.
See the
Pressing the ► button displays the PERFECT FIT dialog.
See the PERFECT FIT item in SETUP menu (
Using the ◄/► buttons switches the picture mode.
The picture modes are combinations of GAMMA and COLOR TEMP
settings. Choose a suitable mode according to the projected source.
• When the combination of GAMMA and COLOR TEMP differs
from pre-assigned modes above, the display on the menu for the
PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and
COLOR TEMP (
46, 47) items in PICTURE menu.
• Lines or other noise might appear on the screen when this function
is operated, but it is not a malfunction.
•
DICOM SIM. is the projector's DICOM® ("Digital Imaging and
Communication in Medicine") simulation mode. This mode simulates
the DICOM standard, which is a standard applicable to digital
communications in medicine, and can be useful for displaying medical
images, such as X-rays photos. This projector is not a medical device
and is not compliant to the DICOM standard, and neither the projector
nor the DICOM SIM. mode should be used for medical diagnosis.
ECO MODE
INSTALLATION
Using the ◄/► buttons turns off/on the Eco mode.
See the ECO MODE item in SETUP menu (
Pressing the ► button displays the INSTALLATION dialog.
See the INSTALLATION item in SETUP menu (
Performing this item resets all of the EASY MENU items except the
RESET
FILTER TIME and LANGUAGE.
A dialog is displayed for conrmation. Selecting the OK using the ►
button performs resetting.
The usage time of the air lter is shown in the menu.
Performing this item resets the lter time which counts usage time
FILTER TIME
of the air lter.
A dialog is displayed for conrmation. Selecting the OK using the ►
button performs resetting.
See the FILTER TIME item in OPTION menu (
LANGUAGE
Using the ◄/► buttons changes the display language.
See the LANGUAGE item in SCREEN menu (
Press the ► or ENTER button to use the menu of PICTURE,
ADVANCED MENU
IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK or
SECURITY.
EXITPress the ◄ or ENTER button to nish the OSD menu.
57).
EASY MENU
57).
70).
60).
45
PICTURE menu
PICTURE menu
From the PICTURE menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
Selecting a mode whose name includes CUSTOM and then
pressing the ► button or the ENTER button displays
a dialog to aid you in adjusting the mode.
This function is useful when you want to
change the brightness of particular tones.
Choose an item using the ◄/► buttons,
GAMMA
and adjust the level using the ▲/▼ buttons.
You can display a test pattern for checking the effect of your
adjustment by pressing the ENTER button.
Each time you press the ENTER button, the
pattern changes as below.
No pattern ð Gray scale of 9 steps
Ramp Gray scale of 15 steps
The eight equalizing bars correspond to eight tone levels of the test
pattern (Gray scale of 9 steps) except the darkest in the left end. If you
want to adjust the 2nd tone from left end on the test pattern, use the
equalizing adjustment bar “1”. The darkest tone at the left end of the
test pattern cannot be controlled with any of equalizing adjustment bar.
• Lines or other noise might appear on the
screen when this function is operated, but it
is not a malfunction.
Using the ▲/▼ buttons switches the color temperature mode.
1 HIGH 1 CUSTOM2 MID 2 CUSTOM3 LOW
6 CUSTOM
6 Hi-BRIGHT-3
5 CUSTOM
To adjust CUSTOM
Selecting a mode whose name includes
CUSTOM and then pressing the ► button
or the ENTER button displays a dialog
to aid you in adjusting the OFFSET and
GAIN of the selected mode.
COLOR TEMP
OFFSET adjustments change the color intensity on the whole tones
of the test pattern. GAIN adjustments mainly affect color intensity on
the brighter tones of the test pattern.
Choose an item using the ◄/► buttons, and adjust the level using
the ▲/▼ buttons.
You can display a test pattern for checking the effect of your
adjustment by pressing the ENTER button.
Each time you press the ENTER button, the pattern changes as below.
No pattern ð Gray scale of 9 steps
Ramp Gray scale of 15 steps
• Lines or other noise might appear on the screen
when this function is operated, but it is not a
malfunction.
Using the ◄/► buttons adjusts the strength of whole color.
Weak ó Strong
• This item can be selected only for a video, s-video and component
COLOR
video signal.
• For an HDMI
(2) applies.
TM
signal, this item can also be selected if either (1) or
(1) HDMI FORMAT item in the INPUT menu for selected port is set
to VIDEO.
(2)
HDMI FORMAT item in the INPUT menu for selected port is set to
AUTO, and the projector recognizes that it receives video signals.
Using the ◄/► buttons adjusts the tint.
Reddish ó Greenish
• This item can be selected only for a video, s-video and component
TINT
video signal.
• For an HDMI
(2) applies.
TM
signal, this item can also be selected if either (1) or
(1) HDMI FORMAT item in the INPUT menu for selected port is set
to VIDEO.
(2)
HDMI FORMAT item in the INPUT menu for selected port is set to
AUTO, and the projector recognizes that it receives video signals.
5 Hi-BRIGHT-2
PICTURE menu
3 CUSTOM
4 Hi-BRIGHT-1
4 CUSTOM
(continued on next page)
47
PICTURE menu
ItemDescription
Using the ◄/► buttons adjusts the sharpness.
SHARPNESS
Weak ó Strong
• There may be some noise and/or the screen may icker for a
moment when an adjustment is made. This is not a malfunction.
ACCENTUALIZER is a function to improve the legibility.
Using the ◄/► buttons adjusts the sharpness.
ACCENTUALIZER
Weak ó Strong
• There may be some noise and/or the screen may icker for a
moment when an adjustment is made. This is not a malfunction.
Using the ▲/▼ cursor buttons changes the active iris control mode.
PRESENTATION ó THEATER ó OFF
PRESENTATION : The active iris displays the best presentation
ACTIVE IRIS
THEATER : The active iris displays the best theater image for
image for both bright and dark scenes.
both bright and dark scenes.
OFF : The active iris is always open.
• The screen may icker when the PRESENTATION or THEATER
modes are selected. If this occurs select OFF.
This projector has 4 memories for adjustment data (for all the items
of the PICTURE menu).
Selecting a function using the ▲/▼ buttons and pressing the ► or
ENTER button performs each function.
SAVE-1 ó SAVE-2 ó SAVE-3 ó SAVE-4
LOAD-4 óLOAD-3 ó LOAD-2 ó LOAD-1
SAVE-1, SAVE-2, SAVE-3, SAVE-4
Performing a SAVE function saves the current adjustment data into
the memory linked in the number included in the function’s name.
• Remember that the current data being stored of a memory will be
lost by saving new data into the memory.
MY MEMORY
LOAD-1, LOAD-2, LOAD-3, LOAD-4
Performing a LOAD function loads the data from the memory linked
in the number included in the function’s name, and adjusts the
picture automatically depending on the data.
• The LOAD functions whose linked memory has no data are
skipped.
• Remember that the current adjusted condition will be lost by
loading data. If you want to keep the current adjustment, please
save it before performing a LOAD function.
• There may be some noise and the screen may icker for a
moment when loading data. This is not malfunction.
• You can perform the LOAD function using MY BUTTON. Please
see MY BUTTON item in OPTION menu (
71, 72).
48
IMAGE menu
From the IMAGE menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table. for selected port
ItemDescription
Using the ▲/▼ buttons switches the mode for aspect ratio.
For a computer signal
CP-X8170:
NORMAL ó 4:3 ó 16:9 ó 16:10
ASPECT
CP-WX8265, CP-WU8460
NORMAL ó 4:3 ó 16:9 ó 16:10 ó NATIVE
For an HDMI
CP-X8170:
NORMAL ó 4:3 ó 16:9 ó 16:10 ó 14:9
CP-WX8265, CP-WU8460
NORMAL ó 4:3 ó 16:9 ó 16:10 ó 14:9 ó NATIVE
For a video signal, s-video signal or component video signal
CP-X8170:
4:3 ó 16:9 ó 14:9
CP-WX8265, CP-WU8460
4:3 ó 16:9 ó 16:10 ó 14:9 ó NATIVE
For an input signal from the LAN, USB TYPE A or USB TYPE B
ports, or if there is no signal
CP-X8170: 4:3 (xed)
CP-WX8265, CP-WU8460
• The NORMAL mode keeps the original aspect ratio of the signal.
TM
signal
:
:
:
: 16:10 (xed)
IMAGE menu
(continued on next page)
49
IMAGE menu
ItemDescription
Using the ◄/► buttons adjusts the over-scan ratio.
Small (It magnies picture) ó Large (It reduces picture)
• This item can be selected only for a video, s-video and component
OVER SCAN
video signal.
• For an HDMI
(2) applies.
TM
signal, this item can also be selected if either (1) or
(1) HDMI FORMAT item in the INPUT menu for selected port is set
to VIDEO.
(2)
HDMI FORMAT item in the INPUT menu for selected port is set to
AUTO, and the projector recognizes that it receives video signals.
Using the ◄/► buttons adjusts the vertical position.
Down ó Up
• Over-adjusting the vertical position may cause noise to appear on
the screen. If this occurs, please reset the vertical position to the
default setting. Pressing the RESET button when the V POSITION
V POSITION
is selected will reset the V POSITION to the default setting.
• When this function is performed on a video signal or an s-video
signal, the range of this adjustment depends on OVER SCAN
(
above) setting. It is not possible to adjust when OVER SCAN is
set to 10.
• This function is unavailable for a signal from the LAN, USB TYPE A / B or HDMI 1 / 2 port.
Using the ◄/► buttons adjusts the horizontal position.
Right ó Left
Over-adjusting the horizontal position may cause noise to appear on
•
the screen. If this occurs, please reset the horizontal position to the
default setting. Pressing the RESET button when the H POSITION is
H POSITION
selected will reset the H POSITION to the default setting.
• When this function is performed on a video signal or an s-video
signal, the range of this adjustment depends on OVER SCAN
(
above) setting. It is not possible to adjust when OVER SCAN is
set to 10.
•
This function is unavailable for a signal from the
A / B or HDMI 1 / 2 port.
LAN, USB TYPE
(continued on next page)
50
ItemDescription
Using the
◄/►
buttons adjusts the horizontal phase to eliminate icker.
Right ó Left
H PHASE
• This item can be selected only for a computer signal or a
component video signal. This function is unavailable for a signal
from the LAN, USB TYPE A / B or HDMI 1 / 2 port.
Using the ◄/► buttons adjusts the horizontal size.
Small ó Large
• This item can be selected only for a computer signal. This function
is unavailable for a signal from the LAN, USB TYPE A / B or HDMI 1
H SIZE
/ 2 port.
• When this adjustment is excessive, the picture may not be
displayed correctly. In such a case, please reset the adjustment
by pressing the RESET button on the remote control during this
operation.
• Images might appear degraded when this function is operated, but
it is not a malfunction.
Selecting this item performs the automatic adjustment feature.
For a computer signal
The vertical position, the horizontal position and the horizontal
phase will be automatically adjusted.
Make sure that the application window is set to its maximum size
prior to attempting to use this feature. A dark picture may still be
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal and s-video signal
The video format best suited for the respective input signal will
be selected automatically. This function is available only when
the AUTO is selected for the VIDEO FORMAT item in the INPUT
AUTO ADJUST
EXECUTE
menu (
automatically set to the default.
For a component video signal
53). The vertical position and horizontal position will be
The vertical position and horizontal position will be automatically set
to the default. The horizontal phase will be automatically adjusted.
• The automatic adjustment operation requires approx. 10 seconds.
Also please note that it may not function correctly with some input.
• When this function is performed for a video signal, a certain extra
such as a line may appear outside a picture.
• When this function is performed for a computer signal, a black
frame may be displayed on the edge of the screen, depending on
the computer model.
• The items adjusted by this function may vary when the FINE or
DISABLE is selected for the AUTO ADJUST item of the SERVICE
item in the OPTION menu (
IMAGE menu
72).
51
INPUT menu
INPUT menu
From the INPUT menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
ItemDescription
Using the ▲/▼ buttons switches the progress mode.
TV ó FILM ó OFF
•
This function works only for a video signal, s-video signal, component
PROGRESSIVE
VIDEO NR
COLOR SPACE
COMPONENT
video signal (of 480i@60 or 576i@50 or 1080i@50/60) and an HDMI
signal (of 480i@60 or 576i@50 or 1080i@50/60)
• When TV or FILM is selected, the screen image will be sharp.
FILM adapts to the 2-3 Pull-Down conversion system. But these
may cause a certain defect (for example, jagged line) of the picture
for a quick moving object. In such a case, please select OFF, even
though the screen image may lose sharpness.
Using the ▲/▼ buttons switches the noise reduction mode.
HIGH ó MID ó LOW
• This function works only for a video signal, s-video signal,
component video signal (of 480i@60 or 576i@50 or 1080i@50/60)
and an HDMI
Using the ▲/▼ buttons switches the mode for color space.
AUTO ó RGB ó SMPTE240 ó REC709 ó REC601
• This item can be selected only for a computer signal (except for
signals from the LAN, USB TYPE A and USB TYPE B ports) or a
component video signal (except SCART RGB).
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a
case, it might be good to select a suitable mode except AUTO.
Using the ▲/▼ buttons switches the function of the COMPONENT
ports.
COMPONENT ó SCART RGB
When the SCART RGB is selected, the COMPONENT (Y, Cb/Pb, Cr/Pr) and VIDEO ports will function as a SCART RGB port.
A SCART adapter or SCART cable is required for a SCART RGB
input to the projector. For details, contact your dealer.
TM
signal (of 480i@60 or 576i@50 or 1080i@50/60).
TM
.
(continued on next page)
52
ItemDescription
The video format for S-VIDEO port and VIDEO port can be set.
(1) Use the ▲/▼ buttons to
select the input port.
(2) Using the ◄/► buttons
switches the mode for video
format.
VIDEO FORMAT
AUTO ó NTSC ó PAL ó SECAM
N-PAL ó M-PAL ó NTSC4.43
• This item is performed only for a video signal from the VIDEO port
or the S-VIDEO port.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the
picture becomes unstable (e.g. an irregular picture, lack of color),
please select the mode according to the input signal.
The video format of HDMITM input signals from the HDMI 1 and 2
ports can be set.
(1) Use the ▲/▼ buttons to
select the HDMI port to be
set.
(2) Use the ◄/►buttons to select the video format.
HDMI FORMAT
AUTO ó VIDEO ó COMPUTER
AUTO: automatically sets the optimum mode.
VIDEO: sets the suitable mode for DVD signals.
COMPUTER: sets the suitable mode for computer signals.
• When the COMPUTER is selected, the functions COLOR
(PICTURE menu), TINT (PICTURE menu) and OVER SCAN
(IMAGE menu) are unavailable.
The digital range of HDMITM input signals from the HDMI 1 and 2
ports can be set.
(1) Use the ▲/▼ buttons to
select the HDMI port to be
set.
(2) Use the ◄/►buttons to select the digital range.
HDMI RANGE
AUTO ó NORMAL ó ENHANCED
INPUT menu
• If the contrast of the screen image is too strong or too weak, try
nding a more suitable mode.
(continued on next page)
AUTO: automatically sets the optimum mode.
NORMAL: s
ENHANCED: s
ets the suitable mode for DVD signals. (16-
ets the suitable mode for computer signals. (0-255)
235)
53
INPUT menu
ItemDescription
The computer input signal type for COMPUTER IN1 and IN2 ports
can be set.
(1)
Use the ▲/▼ buttons to select the COMPUTER IN port to be set.
(2) Use the ◄/► buttons to select
the computer input signal type.
COMPUTER IN
AUTO ó SYNC ON G OFF
• Selecting the AUTO mode allows
you to input a sync on G signal or component video signal from the
port.
• In the AUTO mode, the picture may be distorted with certain
input signals. In such a case, remove the signal connector so that
no signal is received and select the SYNC ON G OFF, and then
reconnect the signal.
Set the frame lock function on/off for each port.
(1) Use the ▲/▼ buttons to select
the input ports.
(2) Use the ◄/► buttons to turn the
FRAME LOCK
frame lock function on/off .
ON ó OFF
• This item can be performed only on a signal with a vertical
frequency of 49 to 51Hz, 59 to 61 Hz.
• When ON is selected, moving pictures are displayed more
smoothly.
(continued on next page)
54
ItemDescription
The resolution for the COMPUTER IN1 and COMPUTER IN2 input
signals can be set on this projector.
(1) In the INPUT menu select the RESOLUTION using the ▲/▼
buttons and press the ► button.
The RESOLUTION menu will be
displayed.
(2) In the RESOLUTION menu select the
resolution you wish to display using
the ▲/▼ buttons.
Selecting AUTO will set a resolution
appropriate to the input signal.
(3) Pressing the ► or ENTER button when
selecting a STANDARD resolution will
automatically adjust the horizontal and
vertical positions, clock phase and
horizontal size.
The INPUT_INFORMATION dialog will be
displayed.
(4) To set a custom resolution use the ▲/▼ buttons to select
RESOLUTION
the CUSTOM and the RESOLUTION_CUSTOM box will be
displayed.
Set the horizontal (HORZ) and
vertical (VERT) resolutions using
the ▲/▼/◄/► buttons.
This function may not support all
resolutions.
(5) Move the cursor to OK on screen and press the ► or ENTER
button. The message "ARE YOU SURE YOU WISH TO
CHANGE RESOLUTION?" appears. To save the setting, press
the ► button.
The horizontal and vertical positions, clock phase and horizontal
size will be automatically adjusted.
The INPUT_INFORMATION dialog
will be displayed.
(6) To revert back to the previous resolution without saving changes,
move the cursor to CANCEL on screen and press the ◄ or
ENTER button.
The screen will then return to the RESOLUTION menu displaying
the previous resolution.
• For some pictures, this function may not work well.
INPUT menu
STANDARD
↓
CUSTOM
↓
55
SETUP menu
SETUP menu
From the SETUP menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
ItemDescription
Selecting this item performs the Automatic keystone distortion
correction. Projector automatically corrects vertical keystone
distortion due to the (forward/backward) setup angle by itself.
This function will be executed only once when selected in the menu.
When the slant of the projector is changed, execute this function again.
• The adjustable range of this function will vary among inputs. For
some input, this function may not work well.
• When the projector is in one of the following conditions, the
AUTO KEYSTONE
KEYSTONE
automatic vertical keystone correction feature may not work
correctly or at all.
- REAR / CEILING or FRONT / CEILING is selected for the
INSTALLATION item in the SETUP menu, and the projector screen
is slanted or tilted downwards.
- The ZOOM adjustment is not set to the full WIDE (wide-angle
focus).
- The projector is nearly horizontal (about ±4°).
- The projector is inclined at about ±35 degrees or over.
• This function is unavailable when the TRANSITION DETECTOR
(
94) is ON or the screen is adjusted by PERFECT FIT (33, 34).
Using the ◄/► buttons corrects the vertical keystone distortion.
Shrink the bottom of the image ó Shrink the top of the image
• The adjustable range of this function will vary among inputs. For
some input, this function may not work well.
• When the zoom adjustment is set to the TELE (telephoto focus),
this function may be excessive. This function should be used when
the zoom adjustment is set to the full WIDE (wide-angle focus)
whenever possible.
• When the horizontal lens shift is not set to the center, this function
may not work well.
• This function is unavailable when the TRANSITION DETECTOR
(
94) is ON or the screen is adjusted by PERFECT FIT (33, 34).
(continued on next page)
56
ItemDescription
Using the ◄/► buttons corrects the horizontal keystone distortion.
Shrink the right of the image ó Shrink the left of the image
• The adjustable range of this function will vary among inputs. For
KEYSTONE
some input, this function may not work well.
• When the horizontal lens shift is not set to the center, this function
may not work well.
• This function is unavailable when the TRANSITION DETECTOR
(
94) is ON or the screen is adjusted by PERFECT FIT (33, 34).
Selecting this item displays the PERFECT FIT dialog.For details,
PERFECT FIT
see PERFECT FIT in Correcting the distortion (
• This is unavailable when the TRANSITION DETECTOR is ON
(
94).
Using the ▲/▼ buttons turns on/off the AUTO ECO MODE.
ON ó OFF
AUTO ECO MODE
• When ON is selected, the projector will always be set to Eco mode
at start-up regardless of the ECO MODE (
message “AUTO ECO MODE” will be displayed for tens of seconds
when the projector starts with this function activated.
Using the ▲/▼ buttons turns off/on the Eco mode.
NORMAL ó ECO
ECO MODE
• When the ECO is selected, acoustic noise and screen brightness
are reduced.
• When AUTO ECO MODE (
always be set to Eco mode at start-up regardless this setting.
Pressing the ►button displays the dialog for changing the
INSTALLATION setting.
SETUP menu
33, 34).
below) setting. An OSD
above) is set to ON, the projector will
INSTALLATION
Use the ▲/▼ buttons to select the desired setting on the
INSTALLATION dialog, and press the ENTER button of the remote
control or the INPUT button of the projector to execute.
If TRANSITION DETECTOR is ON and the INSTALLATION status
is changed, the TRANSITION DETECTOR ON alarm (
displayed when the projector is restarted.
(continued on next page)
FRONT / DESKTOP
REAR / DESKTOP
REAR / CEILING
FRONT / CEILING
94) will be
57
SETUP menu
ItemDescription
Using ▲/▼ buttons switches the standby mode setting between
NORMAL and SAVING.
NORMAL ó SAVING
When SAVING is selected, the power consumption in the standby
mode is lowered with some functional restriction as below:
• When SAVING is selected, the RS-232C communication control
except to turn the projector on and the network function are disabled
while the projector is in the standby mode. If the COMMUNICATION
TYPE in the COMMUNICATION menu is set to NETWORK
BRIDGE, all of the RS-232C commands are disabled (
STANDBY MODE
• When SAVING is selected, AUDIO OUT STANDBY setting of
AUDIO SOURCE (
59) is invalid, and no signal is output from
AUDIO OUT port in the standby mode.
• When SAVING is selected, STANDBY setting of MONITOR OUT
is invalid, and no signal is output from MONITOR OUT port in the
standby mode.
• When SAVING is selected, the CENTERING feature while the
projector is in the standby mode is disabled.
•
When SAVING is selected, the Status Monitor and its button
operation are unavailable while the projector is in the standby mode.
•
When SAVING is selected, the HDMI Link function is disabled while
the projector is in the standby mode.
While the image signal from the input port chosen in step (1) is
projected, the image signal from the input
port selected in step (2) is output to
MONITOR OUT port.
(1) Choose a picture input port using
▲/▼ buttons.
MONITOR OUT
Choose STANDBY to select the
picture output in the standby mode.
(2) Select one of the COMPUTER IN
ports using ◄/► buttons.
Select OFF to disable the MONITOR OUT port for the input port or standby
mode chosen in the step (1).
75, 76).
58
AUDIO menu
From the AUDIO menu, items shown in the table below
can be performed. Select an item using the ▲/▼ cursor
buttons, and press the ► cursor button or the ENTER
button to execute the item. Then perform it according to
the following table.
ItemDescription
VOLUME
AUDIO SOURCE
Using the ◄/► buttons adjusts the volume of the audio output.
Low ó High
While the image signal from the input port chosen in step (1) is
projected, the audio signal from the input port selected in step (2) is
output to the AUDIO OUT port of this projector.
(1) Choose a picture input port using the
▲/▼ buttons.
Choose AUDIO OUT STANDBY to
select the sound output in the standby
mode.
(2) Select an audio input port or the mute
icon using the ◄/► buttons.
The icons indicate the following;
No.1: AUDIO IN1 port No.2: AUDIO IN2 port
No.3: AUDIO IN3 ports No.4: LAN port
No.5: USB TYPE A ports No.6: USB TYPE B port
No.7: HDMI 1 port No.8: HDMI 2 port
: mutes the sound
• Audio input from port nos.4 to 8 can only be selected by each of
the picture input ports.
• C.C. (Closed Caption) is automatically activated when
and an input signal containing C.C. is received. This function is
available only when the signal is NTSC for VIDEO or S-VIDEO, or
480i@60 for COMPONENT, COMPUTER IN1 or COMPUTER IN2,
and when AUTO is selected for DISPLAY in the C.C. menu under the
SCREEN menu (
66).
AUDIO menu
is selected
59
SCREEN menu
SCREEN menu
From the SCREEN menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
ItemDescription
Using the ▲/▼/◄/► buttons switches the OSD (On Screen
Display) language.
LANGUAGE
MENU POSITION
BLANK
ENGLISH ó FRANÇAIS ó DEUTSCH ó ESPAÑOL
(shown in the LANGUAGE dialog)
Press the ENTER or INPUT button to save the language setting.
Using the ▲/▼/◄/► buttons adjusts the menu position.
To quit the operation, press the MENU button on the remote control
or keep no operation for about 10 seconds.
Using the ▲/▼ buttons switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature
(
25). It is displayed by pressing the AV MUTE button on the
remote control.
MyScreen ó ORIGINAL ó BLUE ó WHITE ó BLACK
MyScreen :
ORIGINAL : Screen preset as the standard screen.
BLUE, WHITE, BLACK : Plain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL
screen will change to the AUTO BLANK screen after several
minutes.
Screen can be registered by the MyScreen item (
62).
(continued on next page)
60
ItemDescription
Using the ▲/▼ buttons switches the mode for the AUTO BLANK
screen.
AUTO BLANK
• To avoid remaining as an afterimage, displayed image will change
to the designated blank color screen by AUTO BLANK after several
minutes at the following conditions.
- When MyScreen or ORIGINAL is displayed as BLANK screen.
- When start-up screen is displayed.
Using the ▲/▼ buttons switches the mode for the start-up screen.
The start-up screen is a screen displayed when no signal or an
unsuitable signal is detected.
START UP
MyScreen :
ORIGINAL : Screen preset as the standard screen.
OFF : Plain black screen.
• To avoid remaining as an afterimage, the START UP screen will
change to the AUTO BLANK screen after several minutes.
• When the ON is selected to the MyScreen PASSWORD item in
the SECURITY menu (
(continued on next page)
BLUE ó WHITE ó BLACK
MyScreen ó ORIGINAL ó OFF
Screen can be registered by the MyScreen item (
92), the START UP is fixed to MyScreen.
SCREEN menu
62).
61
SCREEN menu
ItemDescription
This item allows you to capture an image for use as a MyScreen
image which can be used as the BLANK screen and START UP
screen. Display the image you want to capture before executing the
following procedure.
(1) Selecting this item displays a dialog
titled “MyScreen”. It will ask you if
you start capturing an image from
the current screen.
Please wait for the target image to be displayed, and press
the ENTER or INPUT button when the image is displayed. The
image will freeze and the frame for capturing will appear.
To stop performing, press the RESET button on the remote
control.
(2) Using the ▲/▼/◄/► buttons adjusts
the frame position.
Please move the frame to the position
of the image which you want to use. The
MyScreen
frame may not be able to be moved for
some input signals.
To start registration, press the ENTER
or INPUT button on the remote control.
To restore the screen and return to the previous dialog, press the
RESET button on the remote control.
Registration may take several minutes.
When the registration is completed, the registered screen and
the following message is displayed for several seconds:
“MyScreen registration is nished.”
If the registration failed, the following message is displayed:
“A capturing error has occurred. Please try again.”
• This function cannot be selected when the ON is selected to the
MyScreen Lock item (
• This function cannot be selected when the ON is selected to the
MyScreen PASSWORD item in SECURITY menu (
• This function is unavailable for a signal from the LAN, USB TYPE A / B or HDMI 1 / 2 port.
63).
92).
(continued on next page)
62
ItemDescription
Using the ▲/▼ buttons turns on/off the MyScreen lock function.
ON ó OFF
MyScreen Lock
When the ON is selected, the item MyScreen is locked. Use this
function for protecting the current MyScreen.
• This function cannot be selected when the ON is selected to the
MyScreen PASSWORD item in SECURITY menu (
Using the ▲/▼ buttons turns on/off the message function.
ON ó OFF
When the ON is selected, the following message function works.
“AUTO IN PROGRESS” while automatically adjusting
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“INVALID SCAN FREQ.”
“NOT AVAILABLE”
“+++ FOCUS +++”
“Searching….” while searching for the input
MESSAGE
“Detecting….” while an input signal is detected
“AUTO ECO MODE” while starting up with AUTO ECO MODE
The indication of the input signal displayed by changing
The indication of the aspect ratio displayed by changing
The indication of the PICTURE MODE displayed by changing
The indication of the ACTIVE IRIS displayed by changing
The indication of the MY MEMORY displayed by changing
The indication of “FREEZE” and “II” while freezing the screen by
pressing the FREEZE button.
The indication of the TEMPLATE displayed by changing.
The indication of the ECO MODE displayed by changing.
• When the OFF is selected, please remember if the picture is
frozen. Do not mistake freezing for a malfunction (
SCREEN menu
92).
36).
(continued on next page)
63
SCREEN menu
ItemDescription
Each input port for this projector can have a name applied to it.
(1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE
NAME and press the ► or ENTER button.
The SOURCE NAME menu will be displayed.
(2) Use the ▲/▼ buttons on the SOURCE
NAME menu to select the port to be
named and press the ► button. The
SOURCE NAME dialog will be displayed.
Right side of the menu is blank until a
name is specied.
(3) Select an icon you would like to assign to
the port in the SOURCE NAME dialog.
SOURCE NAME
The name assigned to the port will also
be automatically switched according to
your icon selection. Press the ENTER
or INPUT button to determine your icon
selection.
(4) Select a number you would like to assign
to the port along with the icon. You can
select the number either from blank (no
number assigned), 1, 2, 3, or 4.
Then press the ENTER or INPUT button.
(5) If you would like to modify the name assigned
to the port, select CUSTOM NAME and press
the ENTER or INPUT button.
(continued on next page)
64
ItemDescription
(6) The current name will be displayed on
the rst line. Use the ▲/▼/◄/► buttons
and the ENTER or INPUT button to
select and enter characters. To erase 1
character at one time, press the RESET
button or press the ◄ and INPUT button
at the same time. Also if you move the
cursor to DELETE or ALL CLEAR on
screen and press the ENTER or INPUT
button, 1 character or all characters will
be erased. The name can be a maximum
SOURCE NAME
(continued)
of 16 characters.
(7) To change an already inserted character,
press the ▲ button to move the cursor to
the rst line, and use the ◄/► buttons to
move the cursor on the character to be
changed.
After pressing the ENTER or INPUT button, the character is
selected. Then, follow the same procedure as described at the
item (6) above.
(8) To nish entering text, move the cursor to the OK on screen and
press the ►, ENTER or INPUT button. To revert to the previous
name without saving changes, move the cursor to the CANCEL
on screen and press the ◄, ENTER or INPUT button.
Using the ▲/▼ cursor buttons switches the mode for the template
screen.
Press the ► cursor (or the ENTER) button to display the selected
template, and press the ◄ cursor button to close the displayed
screen.
The last selected template is displayed when the MY BUTTON
allocated to the TEMPLATE function is pressed (
TEMPLATE
TEST PATTERN ó DOT-LINE1 ó DOT-LINE2 ó DOT-LINE3
STACK ó MAP2 ó MAP1 ó CIRCLE2 ó CIRCLE1 ó DOT-LINE4
You can turn a map upside down and scroll it horizontally when
MAP1 or MAP2 is selected. To invert or scroll the map, display
the guidance by pressing the RESET button on the remote three
seconds or more when MAP1 or MAP2 appears.
SCREEN menu
71).
(continued on next page)
65
SCREEN menu
ItemDescription
The C.C. is the function that displays a
transcript or dialog of the audio portion of
a video, les or other presentation or other
relevant sounds. It is required to have NTSC
format video or 480i@60 format component
video source supporting C.C. feature to
utilize this function.
It may not work properly, depending on equipment or signal source.
In this case, please turn off the Closed Caption.
DISPLAY
Select Closed Caption DISPLAY setting from following options using
▲/▼ buttons.
AUTO ó ON ó OFF
AUTO : Closed Caption automatically appears when the input signal
(C.C. compatible) from the port with the mute icon set at
AUDIO SOURCE is selected.
ON : Closed Caption is on.
OFF : Closed Caption is off.
• The caption is not displayed when the OSD menu is active.
• The Closed Caption is the function to display the dialogue,
C.C.
(Closed Caption)
narration, and / or sound effects of a television program or other
video sources. The Closed Caption availability is depending upon
broadcaster and/or content.
MODE
Select Closed Caption MODE setting from following options using
▲/▼ buttons.
CAPTIONS ó TEXT
CAPTIONS : Display Closed Caption.
TEXT : Display Text data, which is for additional information such as
news reports or a TV program guide. The information covers
the entire screen. Not all of the C.C. program has Text
information.
CHANNEL
Select Closed Caption CHANNEL from following options using ▲/▼
buttons.
1 ó 2 ó 3 ó 4
1: Channel 1, primary channel / language
2: Channel 2
3: Channel 3
4: Channel 4
The channel data may vary, depending on the content. Some
channel might be used for secondary language or empty.
(continued on next page)
66
ItemDescription
PinP POSITION
Using ▲/▼ buttons on the remote control changes the position of
sub area in PinP mode (
SCREEN menu
40).
67
OPTION menu
OPTION menu
From the OPTION menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to execute
the item, except for the items LAMP TIME and FILTER
TIME. Then perform it according to the following table.
ItemDescription
The ports can be set to be ignored in searching by the AUTO
SEARCH function (
panel.
(1) Choose a picture input port using the
▲/▼ buttons.
SOURCE SKIP
AUTO SEARCH
AUTO
KEYSTONE
(continued on next page)
68
(2) Using the ◄/►buttons turns on/off the
SOURCE SKIP function.
NORMAL ó SKIP
The port that is set to SKIP will be ignored.
• It is not possible to set SKIP to all ports at the same time.
• This setting is not valid when in the PbyP / PinP mode (
Using the ▲/▼ buttons turns on/off the automatic signal search
function.
ON ó OFF
When the ON is selected, detecting no signal automatically cycles
through input ports in the following order. The search is started from
the current port. Then when an input is found, the projector will stop
searching and display the image.
COMPUTER IN1
VIDEO
S-VIDEO COMPONENT HDMI 2 HDMI 1
• It may take several seconds to project the images from the
USB TYPE B port.
Using the ▲/▼ buttons turns on/off the automatic keystone function.
ON ó OFF
ON: Automatic keystone distortion correction will be executed
whenever changing the slant of the projector.
OFF: This function is disabled. Please execute the AUTO
KEYSTONE (EXECUTE) in the SETUP menu for automatic
keystone distortion correction.
• When the projector is suspended from the ceiling this feature will
not function properly so select the OFF.
• This function will be unavailable when the Transition Detector is on
(
94).
below) or in selecting by buttons on the control
ð
COMPUTER IN2
ð
LAN
ð
USB TYPE A
USB TYPE B
37).
ItemDescription
Using the ▲/▼ buttons turns on/off the DIRECT POWER ON
function.
ON ó OFF
When set to the ON, the lamp in projector will be automatically turned
DIRECT POWER
ON
on without the usual procedure (
supplied with the power after the power was cut while the lamp was on.
• This function does not work as long as the power has been
supplied to the projector while the lamp is off.
• After turning the lamp on by the DIRECT POWER ON function,
if neither input nor operation is detected for about 30 minutes, the
projector is turned off, even though the AUTO POWER OFF function
(
below) is disabled.
Using the ▲/▼ buttons adjusts the time to count down to
automatically turn the projector off.
Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE)
OPTION menu
24), only when the projector is
AUTO POWER
OFF
When the time is set to 0, the projector is not turned off
automatically.
When the time is set to 1 to 99, and when the passed time with
no-signal or an unsuitable signal reaches at the set time, the
projector lamp will be turned off.
If one of the projector's buttons or the remote control buttons
is pressed or one of the commands (except get commands) is
transmitted to the CONTROL port during the corresponding time,
projector will not be turned off.
Please refer to the section Turning off the power (
Using the ▲/▼ buttons sets the time from closing the lens shade to
automatically turning the projector off.
SHADE TIMER
• The shade will open automatically when turning the projector on
again.
(continued on next page)
1h ó 3h ó 6h
24).
69
OPTION menu
ItemDescription
Using the ▲/▼ buttons selects the function of USB TYPE B port.
To use this function, you need to connect the USB TYPE B port of
the projector and the type A USB port of a computer.
MOUSE ó USB DISPLAY
MOUSE: The accessory remote control works as the simple mouse
and keyboard of the computer.
USB DISPLAY: The port works as an input port that receives image
USB TYPE B
• It may take several seconds to project the images from the USB
signals from the computer (
TYPE B port.
• In the following cases, a message to notify you that USB TYPE B
port is not available for picture input appears together with the USB
TYPE B dialog:
- This setting is switched to MOUSE while a picture input from the
USB TYPE B port is projected.
- The USB TYPE B port is selected as the picture input source while
this setting is set to MOUSE.
The lamp time is the usage time of the lamp, counted after the last
resetting. It is shown in the OPTION menu.
Pressing the RESET button on the remote control or the ► button
of the projector displays a dialog.
To reset the lamp time, select the OK using the ► button.
LAMP TIME
CANCEL ð OK
• Please reset the lamp time only when you have replaced the lamp,
for a suitable indication about the lamp.
• For the lamp replacement, see the section Replacing the lamp
(
112 ).
• The lamp time can be checked also with the Status Monitor (
The lter time is the usage time of the air lter, counted after the last
resetting. It is shown in the OPTION menu.
Pressing the RESET button on the remote control or the ► button
of the projector displays a dialog.
To reset the lter time, select the OK using the ► button.
FILTER TIME
CANCEL ð OK
• Please reset the lter time only when you have cleaned or
replaced the air lter, for a suitable indication about the air lter.
• For the air lter cleaning, see the section Cleaning and replacing
the air lter (
114 ).
• The lter time can be checked also with the Status Monitor (
108).
22).
22).
(continued on next page)
70
ItemDescription
This item is to assign one of the following functions to MY BUTTON
(1 to 4) on the remote control (
(1) Use the ▲/▼ buttons on the MY BUTTON menu to select a
button from MY BUTTON - 1 to 4 and press the ► or ENTER
button to display the MY BUTTON setup dialog.
(2) Then using the ▲/▼/◄/► buttons sets one of the following
functions to the chosen button. Press the ENTER or INPUT
button to save the setting.
SLIDESHOW: Selects the input from USB TYPE A, and starts a
Slideshow.
MY IMAGE: Displays the MY IMAGE menu (
MESSENGER: Turns the messenger text displayed on the screen
on/off (
5. Messenger Function in the Network Guide).
When there is no transferred text data to display, the message
”NO MESSENGER DATA" appears.
SHADE: Turns the lens shade closed and opened (
PbyP / PinP SWAP: Swaps the picture on the right with one on
the left in the PbyP mode. Swaps the primary picture and the
secondary picture in the PinP mode. (
INFORMATION: Displays SYSTEM_INFORMATION,
79), WIRELESS INFORMATION
MY BUTTON
INPUT_INFORMATION (
(
84), WIRED INFORMATION (86) or nothing.
AUTO KEYSTONE: Performs automatic keystone distortion
correction (
56).
MY MEMORY: Loads one of adjustment data stored (
When more than one data are saved, the adjustment
changes every time the MY BUTTON is pressed.
When no data is saved in memory, the
dialog "No saved data" appears.
When the current adjustment is not
saved to memory, the dialog as shown in
the right appears.
If you want to keep the current adjustment, please press
the ► button to exit. Otherwise loading a data will overwrite the
current adjusted condition.
ACTIVE IRIS: Changes the active iris mode (
PICTURE MODE: Changes the PICTURE MODE (
FILTER RESET: Displays the lter time reset conrmation dialogue
70).
(
TEMPLATE: Makes the template pattern selected to the TEMPLATE
item (
65) appear or disappear.
MUTE: Turns the audio mute on/off.
RESOLUTION: Turns on/off the RESOLUTION dialog (
ECO MODE: Changes the ECO MODE dialog (
6).
37)
OPTION menu
88).
36).
48).
44).
57).
48).
55).
(continued on next page)
71
OPTION menu
ItemDescription
ACCENTUALIZER: Turns on/off the ACCENTUALIZER dialog
MY BUTTON
(continued)
STATUS MONITOR: Turns on/off the back light of status monitor
22). This function is unavailable when SAVING is selected in
(
STANDBY MODE while the projector is in the standby mode.
Selecting this item displays the SERVICE
menu.
Select an item using the ▲/▼ buttons,
and press the ► button or the ENTER
button on the remote control to execute
the item.
ALTITUDE
Using the ▲/▼ buttons switches the rotation speed of the cooling
fans. It is recommended to leave it at AUTO usually.
HIGH-2 ó HIGH-1 ó NORMAL ó AUTO
AUTO: The projector changes the rotation speed automatically to
suit the altitude and other environmental factors.
Choose an option below when there is a trouble with the
AUTO mode.
NORMAL: This mode can be used below 1600m (5250ft.).
HIGH-1: This mode can be used between 1600 to 2300m (5250 to
SERVICE
HIGH-2: This mode can be used above 2300m (7550ft.).
7550ft.).
AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. When the
DISABLE is selected, the automatic adjustment feature is disabled.
FINE ó FAST ó DISABLE
FINE: Finer tuning including H.SIZE adjustment.
FAST: Faster tuning, setting H.SIZE to prearranged data for the
input signal.
• Depending on conditions, such as input image, signal cable to
the projector, environment around the projector, etc., the automatic
adjustment may not work correctly. In such a case, please
choose DISABLE to disable the automatic adjustment, and make
adjustment manually.
GHOST <Only for CP-X8170 / CP-WX8265>
(1) Select a color element of ghost using
the ◄/► buttons.
(2) Adjust the selected element using the ▲/▼ buttons to disappear
ghost.
(
48).
(continued on next page)
72
ItemDescription
FILTER MESSAGE
Use the ▲/▼ button to set the timer for notifying by the message
when to replace the lter unit
1000h ó 2000h ó 5000h ó 10000h ó 15000h ó 20000h ó OFF
After choosing an item except OFF, the message “REMINDER ***
HRS PASSED ....” will appear after the timer reaches the interval
time set by this feature (
119 ).
When the OFF is chosen, the message will not appear. Utilize this
feature to keep the air lter clean, setting the suitable time according
to your environment of this projector.
• Please take care of the lter unit periodically, even if there is
no message. If the air lter becomes to be blocked by dust or
other matter, the internal temperature will rise, which could cause
malfunction, or reduce the lifetime of the projector.
• Please be careful with the operating environment of the projector
and the condition of the lter unit.
SERVICE
(continued)
LENS TYPE
(1) Select the lens type currently used using the ▲/▼ buttons and
press the ► or ENTER button. If AUTO is selected, the projector
determines the lens type automatically.
(2) A message dialog is displayed for conrmation. Press the ► or
ENTER button to save the lens type.
• This setting has an inuence on the keystone distortion etc.
• The lens type determined by the projector will be displayed on the
right of "AUTO".
• If the projector cannot determine the lens type automatically when
this item is set to AUTO, "UNKNOWN LENS" is displayed on the
right of "AUTO".
• About the optional lens, ask your dealer.
LENS LOCK
Using the ▲/▼ buttons turns on/off the lens lock feature. When ON
is selected, the buttons (ZOOM, ZOOM + / -, FOCUS + / -, LENS
SHIFT, LENS MEMORY) are locked.
ON ó OFF
OPTION menu
(continued on next page)
73
OPTION menu
ItemDescription
KEY LOCK
(1) Use the ▲/▼ buttons to choose the operations control.
CONTROL PANEL ó REMOTE CONTROL
(2) Use the ◄/► buttons to select ON or
OFF.
ON ó OFF
Selecting ON in Step 2 locks the buttons except STANDBY, ON
and STANDBY/ON on the operations control selected in Step 1.
Selecting OFF releases the locked buttons on the operations control
selected in Step 1.
• Please use this function to prevent tampering or accidental
operation.
• It's not possible to disable both options at the same time.
REMOTE RECEIV.
(1) Select a remote sensor using the ▲/▼ button.
FRONT ó REAR
(2) Switch it using the ◄/► button.
ON ó OFF
SERVICE
(continued)
• When one sensor is turned off, the other cannot be turned off too.
REMOTE FREQ.
(1) Use the ▲/▼ button to change the projector's remote sensor
frequency setting (
1:NORMAL ó 2:HIGH
(2) Use the ◄/► button to change the
projector's remote sensor on or off.
ON ó OFF
The factory default setting is for both 1:NORMAL and 2:HIGH to be
on. If the remote control does not function correctly, disable either of
them.
• It's not possible to disable both options at the same time.
REMOTE ID
Use the ▲/▼ buttons on the REMOTE ID menu to select ID and
press the ► button.
ALL ó 1 ó 2 ó 3 ó 4
4, 18).
The projector is controlled by the remote control whose ID button
is set the same number as this number. When the ALL is selected,
the projector is controlled by a remote control irrespective of the ID
setting.
(continued on next page)
74
ItemDescription
Selecting this item displays COMMUNICATION
menu.
In this menu, you can congure the serial
communication settings of the projector using the
CONTROL port.
OPTION menu
SERVICE
(continued)
COMMUNICATION
(continued on next page)
• Select an item using the cursor buttons ▲/▼.
Then pressing the ► button opens the submenu
for the setting item you selected. Or, pressing
the ◄ button instead of the ► button makes the
menu back to the previous one without changing
the setup. Each submenu can be operated as
described above.
• When COMMUNICATION TYPE (
below) is
set to OFF, the other items except STACK in
COMMUNICATION menu are invalid.
• For the function of serial communication, refer to
the Network Guide.
75
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION
(continued on next page)
COMMUNICATION TYPE
Select the communication type for transmission via
the CONTROL port.
NETWORK BRIDGE (WIRELESS)
NETWORK BRIDGE (WIRED)
OFF
NETWORK BRIDGE: Select this type, if it is
required to control an external device as a
network terminal, via this projector from the
computer. Select WIRELESS or WIRED as your
network connection mode.
The CONTROL port doesn't accept RS-232C
commands (
6. Network Bridge Function in
the Network Guide)
OFF: Select this mode to receive RS-232C
commands using the CONTROL port.
• OFF is selected as the default setting.
• When you select the NETWORK BRIDGE, check
the item, TRANSMISSTION METHOD (
77)
76
ItemDescription
SERIAL SETTINGS
Select the serial communication condition for the
CONTROL port.
BAUD RATE
4800bps ó 9600bps ó 19200bps ó 38400bps
PARITY
NONE ó ODD ó EVEN
•
The BAUD RATE is xed to 19200bps and PARITY
is xed NONE when the COMMUNICATION TYPE
SERVICE
(continued)
COMMUNICATION
(continued)
is set to OFF
TRANSMISSION METHOD
Select the transmission method for communication by
(
the NETWORK BRIDGE from the CONTROL port.
HALF-DUPLEX ó FULL-DUPLEX
HALF-DUPLEX: This method lets the projector
make two way communication, but only one
direction, either transmitting or receiving data, is
allowed at a time.
FULL-DUPLEX: This method lets the projector
make two way communication, transmitting and
receiving data at the same time.
• HALF-DUPLEX is selected as the default setting.
• If you select HALF-DUPLEX, check the setting of
the item RESPONSE LIMIT TIME (
75, 76).
OPTION menu
78).
(continued on next page)
77
OPTION menu
ItemDescription
RESPONSE LIMIT TIME
Select the time period to wait for receiving
response data from other device communicating by
the NETWORK BRIDGE and the HALF-DUPLEX
through the CONTROL port.
OFF ó 1s ó 2s ó 3s
OFF: Select this mode if it is not required to check
the responses from the device that the projector
sends data to. In this mode, the projector can
send out data from the computer continuously.
1s /2s /3s: Select the time period to keep the
projector waiting for response from the device
SERVICE
(continued)
COMMUNICATION
(continued)
that the projector sends data to. While waiting the
response, the projector does not send out any
data from the CONTROL port.
• This menu is available only when the NETWORK
BRIDGE is selected for the COMMUNICATION
TYPE and the HALF-DUPLEX is selected for the
TRANSMISSION METHOD (
• OFF is selected as the default setting.
STACK
Selecting this item displays the STACK menu.
For more information, please see Instant Stack Guide.
• When STACK MODE is set to MAIN or SUB,
the other items in COMMUNICATION menu are
invalid.
77).
(continued on next page)
78
ItemDescription
INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”.
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock
function is working.
• The “SCART RGB” message means the COMPONENT ports
are working as a SCART RGB input port. Please refer to the
SERVICE
(continued)
COMPONENT item in INPUT menu (
• This item can't be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is
displayed together with the input information in the
INPUT_INFORMATION box (
FACTORY RESET
Selecting OK using the ► button performs this function. By
this function, all the items in all of menus will collectively return
to the initial setting. Note that the items LAMP TIME, FILTER
TIME, LANGUAGE, FILTER MESSAGE, STANDBY MODE,
COMMUNICATION, NETWORK and SECURITY settings are not
reset.
CANCEL ð OK
96).
OPTION menu
52).
79
NETWORK menu
NETWORK menu
Remember that incorrect network settings on this
projector may cause trouble on the network. Be sure
to consult with your network administrator before
connecting to an existing access point on your network.
Select “NETWORK” from the main menu to access the
following functions.
Select an item using the ▲/▼ cursor buttons on the
projector or remote control, and press the ► cursor button on the projector or
remote control, or ENTER button on the remote control to execute the item. Then
perform it according to the following table.
See the Network Guide for details of NETWORK operation.
NOTE
• To use the wireless network function of this projector, the designated
USB wireless adapter that is sold as an option is required. Do not use any
extension cable or device when connecting the adapter to the projector.
• The projector does not allow both wireless and wired LAN to be connected to
the same network.
• Do not set the same network address for both wireless and wired LAN.
• If you are not utilizing SNTP (3.1.8 Date/Time Settings in the Network Guide), then you must set the DATE AND TIME during the initial installation.
• The network communication control is disabled while the projector is in
standby mode if the STANDBY MODE item of SETUP menu is set to SAVING.
Please connect the network communication to the projector after setting the
STANDBY MODE to NORMAL (58).
ItemDescription
Selecting this item displays the WIRELESS
SETUP menu for the wireless LAN.
Use the ▲/▼ buttons to select an item,
and the ► or ENTER button on the remote
control to perform the item.
WIRELESS
SETUP
(continued on next page)
80
MODE
Use the ▲/▼ buttons to select the mode of the
network communication system. Select according
to the settings of your computer.
AD HOC ó INFRASTRUCTURE
To save the setting, press the ► button.
• When ADHOC is selected, IEEE802.11 n cannot
be used.
• If ADHOC is set to MODE while one of WPAPSK or WPA2-PSK is selected in ENCRYPTION,
the ENCRYPTION (
automatically.
82) setting switches to OFF
ItemDescription
Use the ▲/▼ buttons to turn DHCP on/off.
ON ó OFF
Select OFF when the network does not have DHCP
DHCP
(Dynamic Host
Conguration
Protocol)
enabled. To save the setting, press the ► button.
• When the “DHCP” setting changes to “ON”, it
takes a little time to obtain IP address from DHCP
server.
• Auto IP function will be assigned an IP address if
the projector could not obtain an IP address from
server even if DHCP is “ON”
Use the ▲/▼/◄/► buttons to enter the IP
ADDRESS.
This function can only be used when DHCP is set
to OFF.
IP ADDRESS
• The IP ADDRESS is the number that identies
this projector on the network. You cannot have two
devices with the same IP ADDRESS on the same
network.
• The IP ADDRESS “0.0.0.0” is prohibited.
Use the ▲/▼/◄/► buttons to enter the same
WIRELESS
SETUP
(continued)
SUBNET
MASK
SUBNET MASK used by your computer.
This function can only be used when DHCP is set
to OFF.
• The SUBNET MASK “0.0.0.0” is prohibited.
Use the ▲/▼/◄/► buttons to enter the DEFAULT
GATEWAY (a node on a computer network that
DEFAULT
GATEWAY
serves as an access point to another network)
address.
This function can only be used when DHCP is set
to OFF.
Use the ▲/▼/◄/► buttons to input the DNS
DNS SERVER
server address.
The DNS server is a system to control domain
names and IP addresses on the Network.
Use the ▲/▼ buttons to enter the TIME
DIFFERENCE.
Set the same TIME DIFFERENCE as the one
set on your computer. If unsure, consult your IT
TIME
DIFFERENCE
manager.
Use the ► button to return to the menu after
setting the TIME DIFFERENCE.
• When this item is set, the same item in the
WIRED SETUP menu is overwritten with the same
setting (
86).
NETWORK menu
(continued on next page)
81
NETWORK menu
ItemDescription
Use the ▲/▼/◄/► buttons to enter the Year (last
two digits), Month, Date, Hour and Minute.
• When this item is set, the same item in the
WIRED SETUP menu is overwritten with the same
setting (
DATE AND
TIME
• The projector will override this setting and retrieve
DATE AND TIME information from the Time server
when SNTP is enabled. (
Settings in the Network Guide)
• This setting will be reset if the projector is turned
off while STANDBY MODE in the SETUP menu
is set to SAVING (
turned off.
Use the ▲/▼ buttons to select the channel of the
wireless LAN to be used while MODE (
to ADHOC. Select according to the settings of your
computer.
The channels 1 to 11 are available. To save the
setting, press the ► button.
WIRELESS
SETUP
(continued)
CH
• The available channels would be various
depending on a country. In addition, wireless
network card might be required due to the
standard.
• This item can only be selected when MODE
is set to ADHOC. When MODE is set to
INFRASTRUCTURE, the channel is automatically
selected.
Use the ▲/▼ buttons to select the encryption
method to be used.
WPA2-PSK(AES) ó WPA2-PSK(TKIP)
OFF WPA-PSK(AES)
ENCRYPTION
WEP 64bitóWEP 128bitóWPA-PSK(TKIP)
To save the setting, press the ► button.
• When MODE (
WPA-PSK and WPA2-PSK cannot be selected.
• If IEEE802.11 n is used while MODE is set to
INFRASTRUCTURE, TKIP and WEP are disabled.
If OFF or AES is not selected, communication will
switch automatically to IEEE802.11 b/g.
86).
3.1.8 Date/Time
58), or when the AC power is
80) is set to ADHOC, either
80) is set
(continued on next page)
82
ItemDescription
Use the ▲/▼
buttons to select the
SSID to display the
SSID menu.
#1 DEFAULT ó #2 DEFAULT ó #3 DEFAULT
#5 CUSTOM ó #4 DEFAULT
Select one of the DEFAULT (#1~#4) and press ►
or ENTER button.
To adjust CUSTOM
Press the ► or ENTER button when the # 5
CUSTOM is selected. The SSID #5 CUSTOM
menu will be appeared.
The current SSID will be displayed on the
(1)
rst line. If not yet written, the line will be blank.
Use the ▲/▼/◄/► buttons and the ENTER or
INPUT button to select and enter characters. To
erase 1 character at one time, press the RESET
button or press the ◄ and INPUT button at the
same time. Also if you move the cursor to DELETE
or ALL CLEAR on screen and press the ENTER or
WIRELESS
SETUP
(continued)
SSID
INPUT button, 1 character or all characters will be
erased. The SSID can be input up to 32 characters.
(2)
To change an
already inserted
character, press
the ▲/▼ button to
move the cursor
to one of the rst
2 lines, and use
the ◄/► buttons
to move the cursor
on the character to
be changed. After
pressing the ENTER
or INPUT button,
the character is
selected. Then,
follow the same
procedure as
described at the
item (1) above.
(3)
To nish entering text, move the cursor to the OK
on screen and press the ►, ENTER or INPUT
button. To revert to the previous name without
saving changes, move the cursor to the CANCEL on
screen and press the ◄, ENTER or INPUT button.
NETWORK menu
(continued on next page)
83
NETWORK menu
ItemDescription
Selecting this item displays the WIRELESS INFORMATION dialog
for viewing the wireless LAN settings. Use the ▲/▼ buttons to
switch the page.
The rst page shows the wireless LAN settings. The second and
subsequent pages display the signal information of wireless LAN
connection devices.
WIRELESS
INFORMATION
• For details of PASSCODE, refer to the manual for “LiveViewer”.
• Nothing (blank) is shown in the PROJECTOR NAME (
SSID (
characters of the PROJECTOR NAME.
• IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY indicate
“0.0.0.0” in the following condition.
(1) The USB wireless adapter is not inserted into the projector.
(2) DHCP is ON and the projector does not get address from DHCP
server.
• Nothing (blank) is shown in the CH and SPEED elds if the USB
wireless adapter is not inserted.
• The actual performance and setting will be shown in the CH eld,
instead of the setting value in the WIRELESS SETUP menu.
• An icon is displayed to the left of the SSID of the device connected
to the projector.
(continued on next page)
83) field until you setup those items. Only the first 16
87) and
84
ItemDescription
Selecting this item displays the WIRED
SETUP menu for the wired LAN.
Use the ▲/▼ buttons to select an item,
and the ► or ENTER button on the remote
control to perform the item.
Use the ▲/▼ buttons to turn DHCP on/off.
ON ó OFF
Select OFF when the network does not have
DHCP
(Dynamic Host
Conguration
Protocol)
DHCP enabled. To save the setting, press the ►
button.
• When the “DHCP” setting changes to “ON”, it
takes a little time to obtain IP address from DHCP
server.
• Auto IP function will be assigned an IP address if
the projector could not obtain an IP address from
server even if DHCP is “ON”.
Use the ▲/▼/◄/► buttons to enter the IP
ADDRESS.
This function can only be used when DHCP is set
WIRED SETUP
IP ADDRESS
to OFF.
• The IP ADDRESS is the number that identies
this projector on the network. You cannot have two
devices with the same IP ADDRESS on the same
network.
• The IP ADDRESS “0.0.0.0” is prohibited.
Use the ▲/▼/◄/► buttons to enter the same
SUBNET
MASK
SUBNET MASK used by your computer.
This function can only be used when DHCP is set
to OFF.
• The SUBNET MASK “0.0.0.0” is prohibited.
Use the ▲/▼/◄/► buttons to enter the DEFAULT
GATEWAY (a node on a computer network that
DEFAULT
GATEWAY
serves as an access point to another network)
address.
This function can only be used when DHCP is set
to OFF.
Use the ▲/▼/◄/► buttons to input the DNS
DNS SERVER
server address.
The DNS server is a system to control domain
names and IP addresses on the Network.
NETWORK menu
(continued on next page)
85
NETWORK menu
ItemDescription
Use the ▲/▼ buttons to enter the TIME
DIFFERENCE.
Set the same TIME DIFFERENCE as the one
set on your computer. If unsure, consult your IT
TIME
DIFFERENCE
manager.
Use the ► button to return to the menu after
setting the TIME DIFFERENCE.
• When this item is set, the same item in the
WIRELESS SETUP menu is overwritten with the
same setting (
WIRED SETUP
(continued)
Use the ▲/▼/◄/► buttons to enter the Year (last
two digits), Month, Date, Hour and Minute.
• When this item is set, the same item in the
WIRELESS SETUP menu is overwritten with the
same setting (
DATE AND
TIME
• The projector will override this setting and retrieve
DATE AND TIME information from the Time server
when SNTP is enabled. (
Settings in the Network Guide)
• This setting will be reset if the projector is turned
off while STANDBY MODE in the SETUP menu
is set to SAVING (
turned off.
Selecting this item displays the WIRED INFORMATION dialog for
viewing the wired LAN settings.
81).
82).
3.1.8 Date/Time
58), or when the AC power is
WIRED
INFORMATION
• For details of PASSCODE, refer to the manual for “LiveViewer”.
• Only the first 16 characters of the PROJECTOR NAME are
displayed.
• IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY indicate
“0.0.0.0” when DHCP is ON and the projector has not gotten address
from DHCP server.
(continued on next page)
86
ItemDescription
(1) Use the ▲/▼ buttons on the
NETWORK menu to select the
PROJECTOR NAME and press
the ► button. The PROJECTOR
NAME dialog will be displayed.
(2) The current PROJECTOR NAME will be displayed on the rst 3
lines. Particular projector name is pre-assigned by default.
Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to
select and enter characters.
To erase 1 character at one time, press the RESET button or
press the ◄ and INPUT button at the same time. Also if you
move the cursor to DELETE or ALL CLEAR on screen and
push the ENTER or INPUT button, 1 character or all characters
will be erased.The PROJECTOR NAME can be input up to 64
PROJECTOR
NAME
characters.
(3) To change an already inserted
character, press the ▲/▼ button to
move the cursor to one of the rst 3
lines, and use the ◄/► buttons to
move the cursor on the character
to be changed. After pressing
the ENTER or INPUT button, the
character is selected. Then, follow
the same procedure as described
at the item (2) above.
(4) To nish entering text, move the cursor to the OK on screen and
press the ►, ENTER or INPUT button. To revert to the previous
PROJECTOR NAME without saving changes, move the cursor
to the CANCEL on screen and press the ◄, ENTER or INPUT
button.
NETWORK menu
(continued on next page)
87
NETWORK menu
ItemDescription
Selecting this item displays the MY
IMAGE menu.
Use the application to transfer the
image data. It can be downloaded
from the Hitachi web site.
(http://www.hitachi-america.us/projectors or http://www.
hitachidigitalmedia.com).
Use the ▲/▼ buttons to select an item which is a still image by the
MY IMAGE (
4. My Image Function in the Network Guide) and the
► or ENTER button to display the image.
• The item without image stored cannot be selected.
MY IMAGE
• The image names are each displayed in 16 characters or less.
To switch the image displayed
Use the ▲/▼ buttons.
To return to the menu
Press the ◄ button on the remote control.
To erase the image displayed and its source le in the projector.
(1) Press the RESET button on the remote
control while displaying an image to display
the MY IMAGE DELETE menu.
(2) Press the ► button to perform to erase.
To stop erasing, press the ◄ button.
Use the ▲/▼ buttons to turn the AMX Device Discovery on/off.
AMX D.D.
(AMX Device
Discovery)
ON ó OFF
When ON is selected, the projector can be detected by controllers
of AMX connected to the same network. For the details of AMX
Device Discovery, visit the AMX web site.
URL: http://www.amx.com/
(continued on next page)
88
ItemDescription
Selecting this item displays the PRESENTATION menu.
Use ▲/▼ buttons to select one of the following items, then press ►
or ENTER button to use the function.
• To use Network Presentation, an exclusive application, “LiveViewer”
is required. It can be installed from the bundled application CD. You
can also download the latest version and relevant information from
the Hitachi website (http://www.hitachi-america.us/projectors or http://
www.hitachidigitalmedia.com). For details of Network Presentation
and instructions to install the “LiveViewer”, refer to the manual for
“LiveViewer”.
If you set a computer to the Presenter mode while
its image is projected, the projector is occupied by
the computer and access from any other computer is
blocked.
QUIT
PRESENTER
MODE
Use this function to quit the Presenter mode and
allow other computers to access the projector.
Select this item to display a dialog.
Press ► button to choose OK in the dialog.
The Presenter mode is cancelled and a message is
displayed indicating the result.
• To make Presenter mode setting, use “LiveViewer”.
PRESENTATION
For details, refer to the manual for “LiveViewer”.
If you set one or more computers to the Multi PC
mode on “LiveViewer” and send their images to the
projector, you can select the display mode on the
projector from two options below.
- Single PC mode: displays the image of the selected
computer on full screen.
- Multi PC mode: displays the images sent from up to
four computers on screen that is divided into quarter
sections.
Select this item to display a dialog.
MULTI PC
MODE
Use the dialog to change the display mode as
explained below.
• To change from Multi PC
mode to Single PC mode, select
one of computers in the dialog
using the ▲/▼/◄/► buttons
and press the ENTER or INPUT
button.
Press the ► button to choose OK, and then press
ENTER or INPUT again. The image for the selected
computer is displayed on full screen.
(continued on next page)
NETWORK menu
(continued on next page)
89
SECURITY menu
ItemDescription
• To change from Single PC
mode to Multi PC mode, press ►
button to choose OK in the
dialog and press the ENTER or
INPUT button.
The display mode is changed.
•
MULTI PC
MODE
(continued)
PRESENTATION
(continued)
For details on how to switch the display mode to Multi
PC mode on your computer, refer to the manual for
“LiveViwer”
• The Presenter mode setting of the selected
computer becomes valid when the display mode is
changed to Single PC mode. Also, the Presenter
mode setting becomes invalid when the display mode
is changed to Multi PC mode, regardless the setting
on the computers.
For details, refer to the manual for “LiveViewer”.
Selecting this item displays the user name. This
function helps you identify from which computer the
DISPLAY
USER NAME
current image is sent.
• You can set a user name for each computer on
“LiveViwer”. For details, refer to the manual for
“LiveViewer”.
Executing this item restarts and initializes the network functions.
Choose the NETWORK RESTART EXECUTE using the button ►.
.
SERVICE
90
Then use the button ► to execute.
Network will be once cut off when choose restart.
If DHCP is selected on, IP address may be changed.
After selecting NETWORK RESTART EXECUTE, NETWORK menu
may not be controlled approx. 30 seconds.
SECURITY menu
SECURITY menu
This projector is equipped with security functions.
From the SECURITY menu, items shown in the table
below can be performed.
To use SECURITY menu: User registration is required
before using the security functions.
Enter to the SECURITY menu
1. Press the ► button. The ENTER PASSWORD box will be displayed.
2. Use the ▲/▼/◄/► buttons to enter the registered password. The
factory default password is as follows.
CP-X8170: 3805
CP-WX8265: 2205
CP-WU8460: 3905
This password can be changed
right side of the ENTER PASSWORD box and press the ► button to
display the SECURITY menu.
• It is strongly recommended the factory default password to be
changed as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box
will be displayed again. If incorrect password is input 3 times, the
projector will turn off. Afterwards the projector will turn off every time
an incorrect password is input.
3. Items shown in the table below can be performed.
(
If you have forgotten your password
(1) While the ENTER PASSWORD box is displayed, press and hold the
RESET button on the remote control for about 3 seconds or press
and hold the INPUT button for 3 seconds while pressing the ►
button on the projector.
(2) The 10 digit Inquiring Code will be displayed. Contact your dealer
with the 10 digit Inquiring Code. Your password will be sent after
your user registration information is conrmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will
close. If necessary, repeat the process from (1).
ItemDescription
(1) Use the ▲/▼ buttons on the SECURITY menu
to select SECURITY PASSWORD CHANGE
and press the ► button to display the ENTER
NEW PASSWORD box.
(2) Use the ▲/▼/◄/► buttons to enter the new password.
(3) Move the cursor to the right side of the ENTER
SECURITY
PASSWORD
CHANGE
NEW PASSWORD box and press the ► button
to display the NEW PASSWORD AGAIN box,
enter the same password again.
Move the cursor to the right side of the NEW
(4)
PASSWORD AGAIN box and press the ►
button and the NOTE NEW PASSWORD box
will be displayed for about 30 seconds, please
make note of the password during this time.
Pressing the ENTER button on the remote control or ► button on the
projector will close the NOTE NEW PASSWORD box.
• Please do not forget your password.
. Move the cursor to the
below)
(continued on next page)
91
SECURITY menu
ItemDescription
The MyScreen PASSWORD function can be used to prohibit access to the
MyScreen function and prevent the currently registered MyScreen image
from being overwritten.
1 Turning on the MyScreen PASSWORD
1-1 Use the ▲/▼ buttons on the SECURITY menu to
select MyScreen PASSWORD and press the ►
button to display the MyScreen PASSWORD on/
off menu.
1-2 Use the ▲/▼ buttons on the MyScreen
PASSWORD on/off menu to select ON.
The ENTER NEW PASSWORD box (small)
will be displayed.
1-3 Use the ▲/▼/◄/► buttons to enter the
password. Move the cursor to the right side
of the ENTER NEW PASSWORD box (small)
and press the ► button to display the NEW
PASSWORD AGAIN box, enter the same
PASSWORD again.
1-4 Move the cursor to the right side of the
NEW PASSWORD AGAIN box and press
the ► button to display the NOTE NEW
PASSWORD box for about 30 seconds,
please make note of the password during
this time.
Pressing the ENTER button on the remote control or ► button on the
MyScreen
PASSWORD
projector will return to MyScreen PASSWORD on/off menu.
When a password is set for MyScreen:
The MyScreen registration function (and menu) will be unavailable.
•
The MyScreen Lock menu will be unavailable.
•
The START UP setting will be locked on MyScreen (and the menu will be
•
unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of these
functions.
Please do not forget your MyScreen PASSWORD.
•
2 Turning off the MyScreen PASSWORD
2-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off
menu.
2-2
Select OFF to display the ENTER
PASSWORD box (large). Enter the registered
password and the screen will return to the
MyScreen PASSWORD on/off menu.
If an incorrect PASSWORD is input, the menu will
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password
3-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off
menu.
3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit
Inquiring Code will be displayed inside the box.
3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will
be sent after your user registration information is conrmed.
ENTER NEW PASSWORD
box (small)
ENTER PASSWORD box
(large)
(continued on next page)
92
ItemDescription
PIN LOCK is a function which prevents the projector from being used unless
a registered Code is input.
1 Turning on the PIN LOCK
1-1 Use the ▲/▼ buttons on the SECURITY menu
to select PIN LOCK and press the ► button or
the ENTER button to display the PIN LOCK on/off
menu.
1-2 Use the ▲/▼ buttons on the PIN LOCK on/
off menu to select ON and the Enter PIN
Code box will be displayed.
1-3 Input a 4 part PIN code using the ▲/▼/◄/►,
COMPUTER 1 or INPUT button.
The PIN Code again box will appear. Reenter
the same PIN code. This will complete the PIN
code registration.
If there is no key input for about 55 seconds
•
while the Enter PIN Code box or the PIN Code again box is displayed,
the menu will close. If necessary, repeat the process from 1-1.
Afterwards, anytime the projector is restarted after AC power is turned off
the Enter PIN Code box will be displayed. Enter the registered PIN code.
The projector can be used after entering the registered PIN code. If an
incorrect PIN code is input, the Enter PIN code box will be displayed again.
PIN LOCK
If an incorrect PIN code is input 3 times, the projector will turn off. Afterwards
the projector will turn off every time an incorrect PIN code is input. The
projector will also turn off if there is no key input for about 5 minutes while
the Enter PIN code box is displayed.
This function will activate only when the projector is started after AC power
is turned off.
Please do not forget your PIN code.
•
2 Turning off the PIN LOCK
2-1 Follow the procedure in 1-1 to display the PIN LOCK on/off menu.
2-2 Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be
displayed.
Enter the registered PIN code to turn the PIN LOCK function off.
If an incorrect PIN code is input 3 times, the projector will turn off.
3 If you have forgotten your PIN code
3-1 While the Enter PIN code box is displayed, press and hold the RESET
button for three seconds or press and hold the INPUT button for 3
seconds while pressing the ► button on the projector.
The 10 digit Inquiring Code will be displayed.
If there is no key input for about 5 minutes
•
while the Inquiring Code is displayed, the
projector will turn off.
3-2 Contact your dealer with the 10 digit Inquiring Code. Your PIN code will
be sent after your user registration information is conrmed.
SECURITY menu
(continued on next page)
93
SECURITY menu
ItemDescription
If this function is set to ON and the vertical angle of
the projector or the INSTALLATION setting is different
from the previous recorded setting, the TRANSITION
DETECTOR ON alarm will be displayed and the input
signal will not be displayed.
• To display the signal again, set this function OFF.
• After about 5 minutes of displaying the TRANSITION DETECTOR ON
alarm, the lamp will turn off.
• Keystone adjustment feature has been prohibited as long as the Transition
Detector function is on.
1 Turning on the TRANSITION DETECTOR
1-1 Use the ▲/▼ buttons on the SECURITY menu to
select TRANSITION DETECTOR and press the ►
or the ENTER button to display the TRANSITION
DETECTOR on/off menu.
Use the ▲/▼ buttons on the TRANSITION
1-2
DETECTOR on/off menu to select ON.
Selecting ON will save the setting of the
current angle and the INSTALLATION setting.
The ENTER NEW PASSWORD box (small)
will be displayed.
1-3 Use the ▲/▼/◄/► buttons to enter a
password. Move the cursor to the right side
of the ENTER NEW PASSWORD box (small)
and press the ► button to display the NEW
TRANSITION
DETECTOR
PASSWORD AGAIN box, enter the same
password again.
1-4 Move the cursor to the right side of the
NEW PASSWORD AGAIN box and press
the ► button to display the NOTE NEW
PASSWORD box for about 30 seconds,
please make note of the password during this time.
Pressing the ENTER button on the remote control or the ► button on the
projector will return to the TRANSITION DETECTOR on/off menu.
• Please do not forget your TRANSITION DETECTOR password.
• This function will activate only when the projector is started after turning off
the AC power.
• This feature may not function properly if the projector is not in a stable
position when ON is selected.
2 Turning off the TRANSITION DETECTOR
2-1
Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.
2-2
Select OFF to display the ENTER
PASSWORD box (large). Enter the registered
password and the screen will return to the
TRANSITION DETECTOR on/off menu.
If an incorrect password is input, the menu will
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password
3-1
Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.
3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit
Inquiring Code will be displayed inside the box.
3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will
be sent after your user registration information is conrmed.
(continued on next page)
94
ENTER NEW PASSWORD
box (small)
ENTER PASSWORD box
(large)
ItemDescription
The MY TEXT PASSWORD function can prevent the MY TEXT from being
overwritten. When the password is set for the MY TEXT;
• The MY TEXT DISPLAY menu will be unavailable, which can prohibit
changing the DISPLAY setting.
• The MY TEXT WRITING menu will be unavailable, which can prevent the
MY TEXT from being overwritten.
1 Turning on the MY TEXT PASSWORD
1-1 Use the ▲/▼ buttons on the SECURITY menu to
select the MY TEXT PASSWORD and press the
► button to display the MY TEXT PASSWORD
on/off menu.
1-2 Use the ▲/▼ buttons on the MY TEXT
PASSWORD on/off menu to select ON. The
ENTER NEW PASSWORD box (small) will
be displayed.
1-3 Use the ▲/▼/◄/► buttons to enter the
password. Move the cursor to the right side
of the ENTER NEW PASSWORD box (small)
and press the ► button to display the NEW
PASSWORD AGAIN box, and then enter the
same password again.
MY TEXT
PASSWORD
1-4 Move the cursor to the right side of the NEW
PASSWORD AGAIN box and press ► button
to display the NOTE NEW PASSWORD box
for about 30 seconds, then please make note
of the password during this time.
Pressing the ENTER button on the remote control or ► button on the
projector will return to the MY TEXT PASSWORD on/off menu.
2 Turning off the MY TEXT PASSWORD
2-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off
menu.
2-2 Select OFF to display the ENTER
PASSWORD box (large). Enter the registered
password and the screen will return to the
MY TEXT PASSWORD on/off menu.
If an incorrect password is input, the menu will close.
If necessary, repeat the process from 2-1
3 If you have forgotten your password
3-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off
menu.
3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit
inquiring code will be displayed inside the box.
3-3 Contact your dealer with the 10 digit inquiring code. Your password will
be sent after your user registration information is conrmed.
SECURITY menu
ENTER NEW PASSWORD
box (small)
ENTER PASSWORD box
(large)
(continued on next page)
95
SECURITY menu
ItemDescription
(1) Use the ▲/▼ buttons on the SECURITY menu to
select the MY TEXT DISPLAY and press the ► or
ENTER button to display the MY TEXT DISPLAY
on/off menu.
(2) Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select
MY TEXT
DISPLAY
MY TEXT
WRITING
on or off.
ON ó OFF
When it is set ON, the MY TEXT will be displayed
on the START UP screen and the INPUT_
INFORMATION when the INFORMATION on the
SERVICE menu is chosen.
• This function is available only when the MY TEXT
PASSWORD function is set to the OFF.
(1) Use the ▲/▼ buttons on the
SECURITY menu to select the MY
TEXT WRITING and press the ►
button. The MY TEXT WRITING dialog
will be displayed.
(2) The current MY TEXT will be displayed
on the rst 3 lines. If not yet written, the
lines will be blank.
Use the ▲/▼/◄/► buttons and the
ENTER or INPUT button to select and
enter characters. To erase 1 character
at one time, press the RESET button or
press the ◄ and INPUT button at the
same time. Also if you move the cursor
to DELETE or ALL CLEAR on screen
and press the ENTER or INPUT button,
1 character or all characters will be
erased. The MY TEXT can be input up
to 24 characters on each line.
(3) To change an already inserted
character, press the ▲/▼ button to
move the cursor to one of the rst 3
lines, and use the ◄/► buttons to
move the cursor on the character to be
changed.
After pressing the ENTER or INPUT button, the character is selected.
Then, follow the same procedure as described at the item (2) above.
(4) To nish entering text, move the cursor to the OK on screen and press
the ►, ENTER or INPUT button. To revert to the previous MY TEXT
without saving changes, move the cursor to the CANCEL on screen and
press the ◄, ENTER or INPUT button.
The MY TEXT WRITING function is available only when the MY TEXT
•
PASSWORD function is set to OFF.
(continued on next page)
96
ItemDescription
Selecting this item displays the SECURITY INDICATOR dialog. Use
the ▲/▼ buttons to select ON or OFF.
SECURITY
INDICATOR
ON ó OFF
When ON is selected while PIN LOCK or TRANSITION DETECTOR
is ON, the SECURITY indicator blinks in yellow in the standby mode
(
93, 94).
STACK LOCK
Selecting this item displays the STACK LOCK dialog. For more
information, please see Instant Stack Guide.
SECURITY menu
97
Presentation tools
Presentation tools
The projector has the following convenient tools that enable on-screen
presentations easily and quickly:
- PC-LESS Presentation (
- Drawing function
Drawing function enables you to draw on the projector’s screen with USB
mouse or tablets connected to the USB TYPE A ports.
For details, refer to the manual for peripheral equipment.
- USB Display (108)
- Network Presentation
For details of Network Presentation, refer to the Network Guide and the
manual for "LiveViewer".
below)
PC-LESS Presentation
The PC-LESS Presentation reads image and audio data from the storage media
inserted into the USB TYPE A ports and displays the image in the following
modes.
The PC-LESS Presentation can be started by selecting the USB TYPE A as the
input source.
This feature allows you to make your presentations without using your computer.
- Thumbnail mode (
- Full Screen mode (103)
- Slideshow mode (105)
[Supported storage media]
• USB memory (USB memory type, USB hard disk and USB card reader type)
•
NOTE
• USB devices with security software may not work.
• Be careful when inserting or removing a USB device. (
Some USB memory devices and/or USB hubs may not operate properly.
99)
12, 101)
[Supported format]
• FAT12, FAT16 and FAT32
• NTFS is not supported.NOTE
[Supported le format and its extension]
• JPEG (.jpeg, .jpg) * Progressive is not supported.
• Bitmap (.bmp) * 16bit mode and compressed bitmap is not supported.
• PNG (.png) * Interlace PNG is not supported.
• GIF (.gif)
• Movie (.avi, .mov) *
(continued on next page)
98
Supported video format: Motion-JPEG
Supported audio format:
WAV (Linear PCM, Stereo 16bit),
IMA-ADPCM
PC-LESS Presentation (continued)
Presentation tools
NOTE
• Files with a resolution larger than the following are not supported.
CP-X8170: 1024 x 768 (Still), 768 x 576 (Movie)
CP-WX8265: 1280 x 800 (Still), 768 x 576 (Movie)
CP-WU8460: 1920 x 1200 (Still), 768 x 576 (Movie)
(* Some computers may not support above resolutions.)
• Files with a resolution smaller than 36 x 36 are not supported.
• Files with a resolution smaller than 100 x 100 may not be displayed.
• Movie images with a frame rate higher than 15 fps cannot be displayed.
• Movie images with a bit rate higher than 20 Mbps cannot be displayed.
• Some supported les may not be displayed.
• Only a frame appears when the content of image data cannot be displayed in
the Thumbnail mode.
• Even with the le format and audio format combinations described above,
playback of some les may fail.
Thumbnail Mode
The Thumbnail mode displays the images stored in USB storage devices on the
Thumbnail screen. Maximum 20 images are displayed in a screen.
If you wish, you can jump into the Full Screen mode or Slideshow mode, after you
select some images in the Thumbnail mode.
The Thumbnail mode will be started as the primary function of the PC-LESS
Presentation after selecting the USB TYPE A as the input source.
Selected image
Thumbnail images
Thumbnail menu
99
Presentation tools
PC-LESS Presentation (continued)
Operating by buttons
You can control the images on the Thumbnail screen with the remote control,
control panel or Web Remote Control. The following functions can be supported
while the Thumbnail screen is displayed.
Button operation
Remote
control
▲/▼/◄/►▲/▼/◄/►[▲]/[▼]/[◄]/[►]Moves cursor.
PAGE UP
PAGE DOWN
ENTERINPUT[ENTER]
Control panel
-
Web Remote
Control
[PAGE UP]
[PAGE DOWN]
Switches pages.
• Displays the selected image
on the Full Screen mode when a
cursor is on a Thumbnail image.
• Displays the SETUP menu
(
below) for the selected image
when a cursor is on a Thumbnail
image number.
Functions
The SETUP menu for the selected image
100
ItemFunctions
SETUP
RETURN
START
STOP
SKIP
ROTATE
Use the ◄/► cursor buttons to switch each setting or use the ►
cursor button to execute the functions as follows.
Press the ► cursor button or ENTER to return to the Thumbnail
screen.
Switch to ON to set the selected image as the rst image in the
Slideshow. This setting information will be saved in the “playlist.
txt” le (
Switch to ON to set the selected image as the last image in the
Slideshow. This setting information will be saved in the “playlist.
txt” le (
Switch to ON to skip the selected image in the Slideshow. This
setting information will be saved in the “playlist.txt” le (
Press the ► cursor or ENTER button to rotate the selected still
image 90 degrees clockwise. This setting information will be
saved in the “playlist.txt” le (
107).
107).
107).
107).
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.