Hitachi CP-WU5500, CP-X5500, CP-WU5505, CP-X5505, CP-WX5500 User Manual

...

Download

Page 1

LCD Projector

CP-WU5500/CP-WX5500/CP-X5550 CP-WU5505/CP-WX5505/CP-X5555

User's Manual (detailed) Network Guide

Thank you for purchasing this product.

This manual is intended to explain only the network function. For proper use of this product, please refer to this manual and the other manuals for this product.

WARNING

product. After reading them, store them in a safe place for future reference.

►Before using this product, be sure to read all manuals for this

Features

This projector has the network function that brings you the following main features.

ü Network Presentation : allows the projector to project computer images transmitted

through a network. (

ü Web Control : allows you to monitor and control the projector through a network from a

computer. (

ü My Image : allows the projector to store up to four still images and project them. ( ü Messenger : allows the projector to display text sent from a computer through a network.

&83)

(

ü Network Bridge : allows you to control an external device through the projector from a

computer. (

NOTE

• The illustrations in this manual are for illustrative purposes. They may differ

slightly from your projector.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

&38)

&86)

• The information in this manual is subject to change without notice.

&78)

&82)

Page 2

Contents

Caution .......................................................................................... 4

1. Network Function ..................................................................... 5

1.1 Web Control ................................................................................................ 5

1.2 Network Presentation . ................................................................................ 6

1.3 My Image Function ..................................................................................... 7

1.4 Messenger Function ................................................................................... 8

1.5 Network Bridge Function ............................................................................. 9

1.6 Other Functions ......................................................................................... 10

1.6.1 E-mail Alerts ................................................................................................................... 10

1.6.2 Projector Management using SNMP .............................................................................. 10

1.6.3 Event Scheduling ........................................................................................................... 10

1.6.4 Command Control via the Network ................................................................................ 10

2. Connection to the network .................................................... 11

2.1 System requirements ............................................................................... 11

2.2 Connection via wired LAN ......................................................................... 12

2.3 Connection setup of Wired LAN ............................................................... 12

2.4 Connection via wireless LAN .................................................................... 14

2.4.1 Connection in Simple Access Point Mode ..................................................................... 16

2.4.2 Connection in Infrastructure Mode ................................................................................. 17

2.5 Applications .............................................................................................. 19

2.6 NETWORK Menu . .................................................................................... 21

3. Web Control ............................................................................ 38

3.1 Projector Web Control ............................................................................... 40

3.1.1 Login .............................................................................................................................. 40

3.1.2 Network Information ....................................................................................................... 41

3.1.3 Network Settings ............................................................................................................ 42

3.1.4 Port Settings .................................................................................................................. 47

3.1.5 Mail Settings .................................................................................................................. 49

3.1.6 Alert Settings .................................................................................................................. 51

3.1.7 Schedule Settings .......................................................................................................... 53

3.1.8 Date/Time Settings ......................................................................................................... 57

3.1.9 Security Settings ............................................................................................................ 59

3.1.10 Projector Control .......................................................................................................... 61

3.1.11 Remote Control ............................................................................................................ 65

3.1.12 Projector Status ........................................................................................................... 66

3.1.13 Network Restart ........................................................................................................... 67

3.1.14 Connection Test ........................................................................................................... 68

Page 3

Contents

3.2 Crestron e-Control

3.2.1 Main window .................................................................................................................... 71

3.2.2 Tools window ................................................................................................................... 73

3.2.3 Info window ..................................................................................................................... 75

3.2.4 Help Desk window ........................................................................................................... 76

3.2.5 Emergency Alert .............................................................................................................. 77

.................................................................................. 69

4. Network Presentation ............................................................. 78

4.1 Outline ...................................................................................................... 78

4.2 Display Mode . ........................................................................................... 79

4.2.1 Single PC mode ............................................................................................................. 79

4.2.2 Multi PC mode ............................................................................................................... 79

4.3 Multi Projector Mode . ............................................................................... 80

4.4 Moderator Control Mode . ......................................................................... 80

4.5 Port Number . ............................................................................................ 81

5. My Image Function ................................................................. 82

6. Messenger Function ............................................................... 83

6.1 Outline ...................................................................................................... 83

6.2 Supported Languages .............................................................................. 84

6.3 Display Style ............................................................................................. 84

7. Network Bridge Function ....................................................... 86

7.1 Connecting devices .................................................................................. 86

7.2 Communication setup ............................................................................... 87

7.3 Communication port ................................................................................. 87

7.4 Transmission method ............................................................................... 88

7.4.1 HALF-DUPLEX .............................................................................................................. 88

7.4.2 FULL-DUPLEX ............................................................................................................... 89

8. Other Functions ...................................................................... 90

8.1 E-mail Alerts ............................................................................................. 90

8.2 Projector Management using SNMP ........................................................ 93

8.3 Event Scheduling ..................................................................................... 95

8.4 Command Control via the Network .......................................................... 98

8.5 Crestron Connected

............................................................................ 103

9. Troubleshooting ................................................................... 104

10. Warranty and after-sales service ...................................... 113

Page 4

Caution

To use the wireless network function of this projector, the designated USB wireless adapter sold as an option is required. For precautions according to the standards and laws, refer to the documents that come with the adapter.

[Restriction on plugging and unplugging the USB wireless adapter]

Before you insert or pull out the USB wireless adapter from the projector, turn off

the power of the projector and pull out the power cord’s plug from the outlet. Do

not touch the USB wireless adapter that is connected to the projector while the projector is receiving AC power. Do not use any extension cable or device when connecting the adapter to the projector.

[Security precautions when using wireless LAN]

It is recommended that security settings, such as SSID and ENCRYPTION, are

specied when using wireless LAN communication. If the security settings are not specied, the contents may be intercepted or it may cause unauthorized access to the system. For details on wireless LAN security settings, refer to 3.1 Projector

Web Control.

CAUTION

►The optional IEEE802.11b/g/n USB wireless adapter uses the 2.4GHz radio

frequency band. You do not need a radio license to use the adapter, but you should be aware of the following:

• DO NOT USE NEAR THE FOLLOWING!

• Microwave ovens

• Industrial, scientic or medical devices

• Designated low power radio stations

• Premises radio stations Using the USB wireless adapter near the above may cause radio interference,

which would result in a decrease in transmission speed or interruption, and

even lead to malfunctioning of devices such as pacemakers.

• Depending on the location where the USB wireless adapter is used, radio wave

interference may occur, which may result in a decrease in transmission speed or interruption in communication. In particular, please be aware that using the

USB wireless adapter at locations where there is reinforced steel, other types of metals or concrete is likely to cause radio wave interference.

• Available Channels The USB wireless adapter uses the 2.4GHz radio frequency band, but

depending on the country or region you are in, the channels that you can use might be limited. Please consult your dealer for information on the usable channels.

• Bringing the optional USB wireless adapter out of the country or region you reside in and using it there could lead to a violation of the radio laws of that

country or region.

Page 5

1. Network Function

This chapter describes the outline of network function.

1.1 Web Control

Connecting the projector and the computer via the network, remote control and

status monitoring of the projector can be performed by Web browser. Two types of interface, ”Projector Web Control” and “Crestron e-Control”, are

available for this projector. (

&38)

Projector Web Control Crestron e-Control

Page 6

1. Network Function

1.2 Network Presentation

The projector can display or play back the computer screen images and audio data that are transmitted through the network.

To use Network Presentation, an exclusive application, "LiveViewer" is required.

The following application is required to use Network Presentation.

OS Application Windows

Mac OSX LiveViewer

iOS(iPhone/iPad) Projector Quick Connection Android Projector Quick Connection

LiveViewer

Page 7

1. Network Function

1.3 My Image Function

The projector can display still images transferred via the network. It is possible to allocate up to 4 image les. MY IMAGE transmission requires an exclusive application for your computer. Use the application to transfer the image data.

Transfer image data

Display image data (ex.

)

Page 8

1. Network Function

1.4 Messenger Function

The projector can display text data transferred via the network on the screen and

play back audio data inside the projector. It is possible to store up to 12 text data.

Transfer text data

Display text data (ex.

)

Page 9

1. Network Function

1.5 Network Bridge Function

This projector is equipped with the NETWORK BRIDGE function to perform mutual conversion of a network protocol and a serial interface. By making use of the NETWORK BRIDGE function, a computer connected to the projector via wireless or wired LAN is able to control an external device via

RS-232C communication using the projector as a network terminal.

TCP/IP data Serial data

Wired LAN

LAN cable

Computer

(CP-WU5505/CP-WX5505/CP-X5555 only)

Wireless

LAN

Protocol change

WIRELESS port

(USB wireless adapter)

HDBaseT port

RS-232C

RS-232C cable

External device

LAN port

CONTROL port

Page 10

1. Network Function

1.6 Other Functions

1.6.1 E-mail Alerts

The projector can automatically send an alert message to the specied e-mail

addresses when the projector detects a certain condition that is requiring maintenance or detected an error. (&90)

1.6.2 Projector Management using SNMP

The SNMP (Simple Network Management Protocol) enables to manage the projector information, which is a failure or warning status, from the computer on the network. The SNMP management software will be required on the computer to use this function. (

&93)

1.6.3 Event Scheduling

The scheduling function enables to setup scheduled events including

power on / power off. It enables to be “self-management” projector.

The schedule can be set in Projector Web Control or OPTION-SCHEDULE menu

in the projector. (

&95)

1.6.4 Command Control via the Network

You can congure and control the projector via the network using RS-232C

commands. (

&98)

Page 11

2. Connection to the network

2.1 System requirements

The following equipments are required to connect the projector to your computer through the network.

■ Common The projector: 1 unit, Computer: 1 or more sets

■ Connecting device for the projector and the computer

1) For the wired connection *1

LAN cable (CAT-5e or greater): 1 piece

2) For the wireless connection *2

- Projector side

IEEE802.11b/g/n USB wireless adapter (option : USB-WL-11N): 1 unit

- Computer side

IEEE802.11b/g/n wireless LAN equipment: 1 unit for each computer *4

*1: The system for using the network function of the projector requires

communication environment conforming to 100Base-TX or 10Base-T.

*2: An access point is required when the wireless LAN connection is used as

Infrastructure mode.

*3: Available encryption methods are as follows. This product cannot be

connected to the wireless network using other encryption method.

Simple Access Point mode Infrastructure mode WPA2-PSK (AES) WPA2-PSK (TKIP) WPA-PSK (AES) WPA-PSK (TKIP) WEP 128bit WEP 64bit -

✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓

✓ ✓

*4: Depending on the type of wireless network device and computer you are using,

the projector may not be able to communicate properly with your computer,

even if the computer is equipped with a built-in wireless LAN function. To eliminate communication problems, use a Wi-Fi certied wireless network device.

■ Web browser

Web browser is required to be installed in your computer to use Web control.

■ Application Exclusive applications are required to be installed in your computer to use

Network Presentation, My Image and Messenger. (

&19)

For Mac users: Mac OS does not support some applications. Refer to System Requirements for Applications (

&19) rst before setting up the connection.

NOTE

• The network function is not available when STANDBY MODE is set to SAVING and the projector is in standby mode. Connect the projector to the network after setting STANDBY MODE to NORMAL. (&SETUP menu in the Operating Guide)

Page 12

2. Connection to the network

Connection via wired LAN

2.2

The connection via wired LAN is available. Set wired LAN for the projector by

following the instructions of your network administrator when connecting to the existing network.

hub

Connection setup of Wired LAN

2.3

1) Connect the projector to the computer via a hub with a LAN cable (CAT-5e or higher).

2) Press the MENU button on the remote control or the control panel of the projector.

The MENU you last used will appear. Use the cursor button to select the following. EASY MENU > ADVANCED MENU > NETWORK > NETWORK SETUP > WIRED SETUP

3) Set the following items in WIRED SETUP.

･ DHCP ･ IP ADDRESS ･ SUBNET MASK ･ DEFAULT GATEWAY ･ DNS SERVER

As for setting an IP address, refer to About IP address. (

Select APPLY, then press the ENTER button to reect the settings.

&13)

Page 13

2. Connection to the network

[About IP address]

■ Setting manually

The Network address portion of the IP address setting on your computer must be the same as the setting on the projector. Also, the entire IP address on the

computer must not overlap with that of the other devices on the same network,

including the projector.

The projector’s settings are as follows. IP address: 192.168.1.254 Subnet mask: 255.255.255.0 (Network address: 192.168.1 in this case) Therefore, specify the computer’s IP address as follows. IP address: 192.168.1.xxx (xxx shows decimal number.) Subnet mask: 255.255.255.0 (Network address: 192.168.1 in this case)

For example Select from 1 to 254 for “xxx” not duplicating with any other equipments. In this case, since the IP address of the projector is “192.168.1.254”, specify a setting between 1 to 253 for the computer.

■ Setting automatically When a DHCP server exists in the connected network, it assigns an IP address to the projector and the computer automatically. If DHCP server is not available, set IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY.

NOTE

•

Although HDBaseTTM and LAN port can be used for wired LAN, they cannot be

used simultaneously.

Connect LAN cable to the port set in WIRED NETWORK

on OPTION - SERVICE - CONTROL TERMINAL menu.

•

The same network address cannot be used for both wireless LAN and wired LAN.

•

If the projector and the computer exist in the same network (i.e., same network

address), you can leave the default gateway eld blank.

• When the projector and the computer exist in different networks, the default

gateway must be set. Consult to the network administrator in detail.

Page 14

2. Connection to the network

Connection via wireless LAN

2.4

Connection via wireless LAN is available with option parts, USB wireless adapter (USB-WL-11N). Wireless LAN has two types of connection, Simple Access Point and

Infrastructure.

Fig. 2.4.a Without an access point communication (Simple Access Point)

Fig. 2.4.b With an access point communication (Infrastructure)

* Simple Access Point is a mode which connects to computers directly.

This projector can assign IP addresses to up to 11 devices.

* Infrastructure is one of the wireless LAN communication methods with having

an access point to communicate. If communicating with existing network, consult with your network administrator.

NOTE

• Network settings can also be changed in Network Settings of Projector Web

Control.

• Wireless LAN initial settings for the projector are as follows.

Mode: Simple Access Point DHCP: Off IP address: 192.168.10.1 Subnet Mask: 255.255.255.0

Default Gateway: 0.0.0.0 DNS Server: 0.0.0.0

SSID: SimpleAccessPoint ※

SSID Broadcast: On

Encryption: Off Channel: 11

※ Change default setting before use not to overlap.

(continued on next page)

Page 15

2. Connection to the network

NOTE

• The same network address cannot be used for both wireless LAN and wired LAN.

• Communication speed of the projector may be deteriorated in

Point

mode depending on the number of connected devices.

Simple Access

• Network communication cannot be available between the devices connected to

the projector in

Simple Access Point

mode.

• When using wireless network function, set NETWORK - WIRELESS NETWORK

to ON.

Page 16

2. Connection to the network

2.4.1 Connection in Simple Access Point Mode

Set the following when connecting the projector and the computer in Simple Access Point mode.

Projector setting

[Restriction on plugging and unplugging the USB wireless adapter] Before you insert or pull out the USB wireless adapter from the projector, turn off

the power of the projector and pull out the power cord’s plug from the outlet. Do

not touch the USB wireless adapter that is connected to the projector while the projector is receiving AC power. Do not use any extension cable or device when connecting the adapter to the

projector

1) Attach the USB wireless adapter to the WIRELESS port of the projector.

2) Turn on the projector.

3) Press the MENU button on the remote control or the control panel of the projector.

The MENU you last used will appear.

Use the cursor button to select the following. EASY MENU > ADVANCED MENU > NETWORK > NETWORK SETUP > WIRELESS SETUP

4) Set the following items in WIRELESS SETUP.

･ MODE: SIMPLE ACCESS POINT ･ IP ADDRESS ･ SSID ･ SSID BROADCAST ･ ENCRYPTION ･ CHANNEL

Select APPLY, then press the ENTER button to reect the settings.

About network settings

･ The fourth octet of the projector's IP address is xed to 1. ･ Subnet mask of the projector is xed to 255.255.255.0.

Computer setting

1) The DHCP server function of the projector is always enabled. Enable the DHCP

setting of the computer.

2) Select SSID set for the projector by following the procedure of wireless connection of the computer. Enter encryption key by following the computer’s instruction if it is encrypted.

NOTE

• As for the procedure of setting network and wireless connection for the

computer, refer to the manual of computer or wireless LAN device.

Page 17

2. Connection to the network

2.4.2 Connection in Infrastructure Mode

Set the following when connecting the projector and the computer in Infrastructure mode.

Projector setting

[Restriction on plugging and unplugging the USB wireless adapter] Before you insert or pull out the USB wireless adapter from the projector, turn off

the power of the projector and pull out the power cord’s plug from the outlet. Do

not touch the USB wireless adapter that is connected to the projector while the projector is receiving AC power. Do not use any extension cable or device when connecting the adapter to the

projector.

1) Attach the USB wireless adapter to the WIRELESS port of the projector.

2) Turn on the projector.

3) Press the MENU button on the remote control or the control panel of the projector.

The MENU you last used will appear.

Use the cursor button to select the following. EASY MENU > ADVANCED MENU > NETWORK > NETWORK SETUP > WIRELESS SETUP

4) Set the following items in WIRELESS SETUP.

･ MODE: INFRASTRUCTURE ･ DHCP ･ IP ADDRESS ･ SUBNET MASK ･ DEFAULT GATEWAY ･ DNS SERVER ･ SSID ･ ENCRYPTION

As for setting an IP address, refer to About IP address. (

&13)

Select APPLY, then press the ENTER button to reect the settings.

Page 18

2. Connection to the network

Connection in Infrastructure Mode (continued)

SSID SCAN LIST function

The connection can be set up by selecting from SSID SCAN LIST without setting SSID and ENCRYPTION in WIRELESS SETUP. The procedure of connecting by SSID SCAN LIST is as follows.

1) Select SSID SCAN LIST in WIRELESS SETUP on NETWORK - NETWORK SETUP.

The list of SSID in wireless network is displayed.

2) Select SSID in wireless network that you want to connect in SSID SCAN LIST.

The display to enter the encryption key appears if it is encrypted. Enter the encryption key by using software keyboard.

3) The icon indicating connected (

) is displayed in SSID SCAN LIST screen

when the connection is complete.

NOTE

•

Transmission speed may be slow depending on the settings of an access point.

•

If the projector and the computer exist in the same network (i.e., same network

address), you can leave the default gateway eld blank.

• When the projector and the computer exist in different networks, the default

gateway must be set. Consult with the network administrator in detail.

• Set wireless LAN for the projector by following the instructions of your network

administrator when connecting to the existing network.

• Open System Authentication is used for WEP encryption, and Shared Key

Authentication is not supported. The authentication with an access point succeeds

and it is regarded that the connection is established normally even when entering

illegal encryption key due to Open System Authentication, but data cannot actually be transmitted.

• IP ADDRESS, SUBNET MASK, and DEFAULT GATEWAY should be set in advance when DHCP is set to OFF.

Page 19

2. Connection to the network

2.5 Applications

The latest version of the application software can be downloaded from the website

below.

http://www.hitachi-america.us/projectors http://www.hitachidigitalmedia.com/ http://www.hitachi-dm.cn/ http://www.hitachi.co.jp/proj/

For iOS/Android Network Presentation software, refer to the URL below for details

and downloads of Projector Quick Connection.

http://www.hitachi.co.jp/Prod/vims/proj/en/

http://www.hitachi.co.jp/proj/

[System Requirements for Applications]

Application Hardware and Software LiveViewer [Windows]

OS:

Windows Vista

(Service Pack 1 or later)

Windows® 7 Windows® 8/8.1 Windows® 10

Graphic card: VGA: 640x480 or higher (recommended XGA:

1024x768)

CPU:

Pentium® 4 (2.8 GHz or higher)

Hard disk space:

100MB or higher

Page 20

2. Connection to the network

[System Requirements for Applications] (continued)

Application Hardware and Software

LiveViewer [Mac]

Mac OSX 10.5 Mac OSX 10.6 Mac OSX 10.7 Mac OSX 10.8

Hard disk space:

15MB or higher

NOTE

•

Only for Intel version. Power Mac is not supported.

• LiveViewer

CD-ROM.

for MAC is not included in the bundled

Download it from the website.

Projector Quick Connection

Projector Image Tool (PJImg)

Projector Messenger Tool (PJMessenger)

[iOS] iOS 6 or later

[Android] Android OS 4.0 or later

OS:

Windows Vista

Windows® 7 Windows® 8/8.1 Windows® 10

CPU:

Pentium® 3 (500MHz or higher)

Hard disk space:

20MB or higher

OS:

Windows Vista

Windows® 7 Windows® 8/8.1 Windows® 10

CPU:

Pentium® 3 (500MHz or higher)

Hard disk space:

20MB or higher

Page 21

2. Connection to the network

2.6 NETWORK Menu

Remember that incorrect network settings on this

projector may cause trouble on the network. Be sure

to consult with your network administrator before connecting to an existing access point on your network. Select “NETWORK” from the main menu to access to the following functions.

Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or

remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table.

NOTE

• When you use wired LAN, rst select which function to use, LAN or HDBaseTTM, in OPTION - SERVICE - CONTROL TERMINAL - WIRED NETWORK menu. (&OPTION menu in the Operating Guide)

• To use the wireless network function of this projector, the designated USB

wireless adapter sold as an option is required. Do not use any extension cable

or device when connecting the adapter to the projector.

•

The projector does not allow both wireless and wired LAN to be connected to

the same network.

• Do not set the same network address for both wireless and wired LAN.

• If you do not use SNTP, then you must set the DATE AND TIME during the initial installation. (&OPTION menu in the Operating Guide)

• When using wireless network function, set NETWORK - WIRELESS

NETWORK to ON.

Page 22

2. Connection to the network

Item Description

Selecting this item displays the dialog for viewing the wireless and wired LAN settings. Use the ▲/▼ buttons to switch the page.

The rst page shows the wireless LAN settings. The second page is for the wired LAN settings, and the third page is for common

setting item.

The following information is displayed.

WIRELESS NETWORK

･

PASSCODE

･

MODE

･

IP ADDRESS

･

SUBNET MASK

･

DEFAULT GATEWAY

･

DNS SERVER

･

MAC ADDRESS

･

SSID

･

SSID BROADCAST

･

ENCRYPTION

･

CHANNEL

NETWORK

INFORMATION

･

SPEED

･

WIRELESS

INFORMATION

(continued on next page)

Passcord supports the connection between the projector and the computer when using Network Presentation. Refer to Network Presentation (&78)

for the details.

NOTE

• IP ADDRESS, SUBNET MASK and

DEFAULT GATEWAY indicate “0.0.0.0” in the

following condition.

(1) The USB wireless adapter is not inserted

into the projector. (2) DHCP is ON and the projector does not get

address from DHCP server. (3) WIRELESS NETWORK is set to OFF.

• Nothing (blank) is shown in the CHANNEL and SPEED elds if the USB wireless adapter is not inserted or WIRELESS NETWORK is set

to OFF.

Page 23

Item Description

The following information is displayed.

PASSCODE

･

IP ADDRESS

･

SUBNET MASK

･

DEFAULT GATEWAY

･

DNS SERVER

･

MAC ADDRESS

･

WIRED

INFORMATION

Passcord enables the projector and the computer to be connected to the network easily when using Network Presentation. Refer to Network

NETWORK

INFORMATION

(continued)

Presentation (

NOTE

• IP ADDRESS, SUBNET MASK and

DEFAULT GATEWAY indicate “0.0.0.0” when

DHCP is ON and the projector has not gotten

address from DHCP server.

The following information is displayed.

PROJECTOR NAME

･

DATE AND TIME

･

SNTP SERVER

OTHER

INFORMATION

･

TIME DIFFERENCE

･

2. Connection to the network

&78) for details.

WIRELESS NETWORK

(continued on next page)

Switches ON/OFF of wireless network function.

ON  OFF

• PROJECTOR NAME and SNTP SERVER may

appear truncated if they are too long.

Page 24

2. Connection to the network

Item Description

Congures wireless network. Setting values are saved after selecting "APPLY".

NOTE

• Setting values are not saved if Menu dissapears before selecting "APPLY".

• Be sure to execute "APPLY" after changing the settings.

NETWORK

SETUP

WIRELESS

SETUP

MODE

(continued on next page)

Switches between SIMPLE ACCESS POINT and INFRASTRUCTURE.

Select the mode of the network communication system. Select according to the settings of your computer.

SIMPLE ACCESS POINT  INFRASTRUCTURE

To save the setting, press the ► button.

NOTE

• The setting changed before switching MODE without selecting "APPLY" is cancelled.

• When switching MODE, it takes 60 seconds to be able to use wireless LAN. In the meantime,

the operating speed of the projector may be decreased and NETWORK INFORMATION may not be displayed correctly.

Page 25

NETWORK

SETUP

WIRELESS

SETUP

(continued)

2. Connection to the network

Item Description

Searches available wireless network and displays

the list of SSID. You can select SSID to connect from the list.

(1) SSID on available wireless network is displayed after selecting SSID SCAN LIST and press the ► button.

SSID SCAN

LIST

NOTE

・The wireless network using the encryption

method not supported by the projector is displayed in the search list.

・A network device of

Simple Access Point

not displayed on SSID SCAN LIST.

not

(continued on next page)

Page 26

2. Connection to the network

Item Description

NETWORK

SETUP

WIRELESS

SETUP

SSID SCAN

LIST

(continued)

Icon Description

he projector is connecting to the wireless

T network.

The wireless network is encrypted.

The intensity of radio wave.

(2) Select SSID that you want to connect and press the ► or ENTER button. The display to enter the encryption key appears if SSID is encrypted. Enter the characters by using software keyboard.

Move the cursor to OK and press the ►, ENTER or INPUT button after entering.

(continued on next page)

NOTE

If you select the [HIDE THE CHARACTERS] checkbox, the characters are hidden.

Page 27

2. Connection to the network

Item Description

(3)

The OSD below is displayed while the

connection is in progress.

The keys other than RESET button are not

available while the connection is in progress.

The connection process is interrupted when pressing the RESET button.

The OSD below is displayed when the connection process is complete.

NETWORK

SETUP

WIRELESS

SETUP

(continued)

SSID SCAN

LIST

(continued)

：

Connection succeeded

The message below is displayed when the connection is not established correctly.

：

NOTE

･ Encryption settings cannot be

Connection failed

Encryption Lock enabled

changed when encryption lock is enabled in Network Settings – Wireless Setup in Projector Web Control. Refer to Encryption

Lock. (

&43)

• Open System Authentication is used for WEP

encryption, and Shared Key Authentication is not supported. The authentication with an access point is succeeded and it is regarded that the connection is established normally

even when entering illegal encryption key

due to Open System Authentication, but data cannot actually be transmitted.

The icon indicating the connection status

(4)

(

) is displayed in SSID SCAN LIST when the

connection is complete.

(continued on next page)

Page 28

2. Connection to the network

Item Description

SSID SCAN

LIST

(continued)

This function is not available in SIMPLE ACCESS

POINT mode.

Congures whether IP address is automatically

obtained or not.

Use the ▲/▼ buttons to turn DHCP on/off.

ON  OFF

This function is not available in SIMPLE ACCESS

POINT mode.

[SIMPLE ACCESS POINT] Refer to "Connection in Simple Access Point Mode".

(&16)

[INFRASTRUCTURE] Congures the IP address when DHCP is disabled.

NETWORK

SETUP

WIRELESS

SETUP

(continued)

DHCP

ADDRESS

Enter the IP ADDRESS. This function can only be used when DHCP is set to OFF.

[SIMPLE ACCESS POINT] This setting is xed to 255.255.255.0. [INFRASTRUCTURE]

SUBNET

MASK

Congures the subnet mask when DHCP is

disabled.

Enter the SUBNET MASK.

This function can only be used when DHCP is set to OFF.

Congures the default gateway when DHCP is

disabled.

DEFAULT

GATEWAY

Enter the DEFAULT GATEWAY address.

This function can only be used when DHCP is set to OFF.

This function is not available in SIMPLE ACCESS

POINT mode.

(continued on next page)

Page 29

Item Description

Congures the DNS server address. Enter the DNS server address.

This function is not available in SIMPLE ACCESS

DNS

SERVER

POINT mode.

NOTE

This setting cannot be obtained automatically.

Congures SSID for wireless network. [SIMPLE ACCESS POINT]

Enter SSID by using software keyboard. Refer to PROJECTOR NAME (

NETWORK

SETUP

WIRELESS

SETUP

(continued)

software keyboard. Default setting of SSID in Simple Access Point mode is [SimpleAccessPoint]. Change default

setting before use not to overlap.

[INFRASTRUCTURE]

SSID

Select one of the DEFAULT (#1~#4) and press ►

or ENTER button.

To adjust CUSTOM

Press the ► or ENTER button when the # 5 CUSTOM is selected. The SSID #5 CUSTOM

menu will be appeared. Enter SSID by using software keyboard. Refer to PROJECTOR NAME (&33) for how to use

software keyboard.

2. Connection to the network

&33) for how to use

(continued on next page)

Page 30

2. Connection to the network

Item Description

Congures SSID BROADCAST.

SSID

BROADCAST

Set this function to OFF when making SSID of a projector not to be displayed in wireless connection list of the computer.

Select the encryption method to be used. WPA2-PSK(AES)  WPA2-PSK(TKIP)

  OFF WPA-PSK(AES)   WEP 64bitWEP 128bitWPA-PSK(TKIP)

WEP 64bit and WEP 128bit are available only in INFRASTRUCTURE mode.

It is required to enter the encryption key when selecting the encryption method other than OFF and

NETWORK

SETUP

WIRELESS

SETUP

(continued)

ENCRYPTION

pressing the ► button.

NOTE

• WPA2-PSK (AES) is recommended

for encryption method of IEEE802.11n. Transmission speed in IEEE802.11n may be slow when other encryption method (WEP, WPA-PSK (TKIP), WPA2-PSK (TKIP)). Change the setting to “AES” if encryption other than “AES” is set.

• Encryption method not included in the selected item cannot be available.

CHANNEL

(continued on next page)

Select the channel of the wireless LAN to be used

while MODE (

&24) is set to SIMPLE ACCESS

POINT.

The channels 1 to 11 are available. To save the setting, press the ► button.

• The available channels vary depending on a

country.

Page 31

2. Connection to the network

Item Description

Congures wired network. Setting values are saved after selecting "APPLY"

NOTE

・Setting values are not saved if Menu dissapears before

selecting "APPLY".

・Be sure to execute "APPLY" after changing the settings.

DHCP

NETWORK

SETUP

/ WIRED SETUP

ADDRESS

SUBNET

MASK

DEFAULT

GATEWAY

DNS

SERVER

(continued on next page)

Congures whether IP address is

automatically

obtained or not.

Use the ▲/▼ buttons to turn DHCP on/off.

ON  OFF

Congures the IP address when DHCP is disabled.

Enter the IP ADDRESS. This function can only be used when DHCP is set to OFF.

Congures the subnet mask when DHCP is disabled. Enter the SUBNET MASK.

This function can only be used when DHCP is set to OFF.

Congures the default gateway when DHCP is

disabled.

Enter the DEFAULT GATEWAY address.

This function can only be used when DHCP is set to OFF.

Congures the DNS server address. Enter the DNS server address.

NOTE

This setting cannot be obtained automatically.

Page 32

2. Connection to the network

Item Description

When you get the time via the network, specify SNTP server with IP address or domain name. Up to 255 characters can be entered for domain

name.

SNTP

SERVER

NETWORK

SETUP

SNTP

They are entered by using software keyboard. Refer to PROJECTOR NAME(

software keyboard.

NOTE

Set the time difference when using SNTP.

SETUP

Enter the time difference. Set the same time difference as the one set on

TIME

DIFFERENCE

your computer. If unsure, consult your network administrator.

Use the ► button to return to the menu after

setting the TIME DIFFERENCE.

(continued on next page)

&33) for how to use

Page 33

Item Description

Any name can be set to the projector to identify it on the network.

(1) Select the PROJECTOR

NAME and press the ► button. The PROJECTOR NAME dialog will be displayed.

Use displayed software keyboard to enter PROJECTOR

NAME.

DELETE : Deletes one character. CLEAR ALL: Deletes all characters. CANCEL : Goes back to network menu after discarding

the entered characters.

OK : Goes back to network menu after saving the entered

characters.

(2) The current PROJECTOR NAME will be displayed on the

rst 3 lines. Particular projector name is pre-assigned by

NETWORK

SETUP

PROJECTOR

NAME

default. Use the ENTER or INPUT button to select and enter

characters. To erase 1 character at one time, press the RESET button

or press the ◄ and INPUT button at the same time. Also if you move the cursor to DELETE or CLEAR ALL on screen

and push the ENTER or INPUT button, 1 character or

all characters will be erased. Up to 64 characters can be

input for the PROJECTOR NAME.

(3) To change an already

inserted character, move the cursor to one of the rst 3 lines, and move the cursor

on the character to be changed. After pressing the ENTER or INPUT button, the character is selected. Then, follow the same procedure as described at

the item (2) above.

(4) To nish entering text, move

the cursor to the OK on screen and press the ►, ENTER or INPUT button.

To revert to the previous PROJECTOR NAME without saving changes, move the cursor to the CANCEL on screen and press the ◄, ENTER or INPUT button.

2. Connection to the network

(continued on next page)

Page 34

2. Connection to the network

Item Description

Selecting this item displays the MY

IMAGE menu. Use the application to transfer the

image data. It can be downloaded from the web site.

Refer to 5. My Image Function (

IMAGE.

Select an item of still image by the MY IMAGE and the ► or

ENTER button to display the image.

• The item without stored image cannot be selected.

MY IMAGE

• Each image name is displayed in 16 characters or less.

To switch the image displayed

To return to the menu

To erase the displayed image and its source le in the

projector. (1) Press the RESET button on the

(2) Press the ► button to erase.

(continued on next page)

&82) for the details of MY

Use the ▲/▼ buttons.

Press the ◄ button on the remote control.

remote control while displaying an

image to display the MY IMAGE DELETE menu.

To stop erasing, press the ◄ button.

Page 35

Item Description

Use the ▲/▼ buttons to turn the AMX Device Discovery on/off.

AMX D.D.

(AMX Device

Discovery)

ON  OFF

When ON is selected, the projector can be

detected by controllers of AMX connected to the same network. For the details of AMX Device Discovery, visit the AMX web site.

URL: http://www.amx.com/

Use the ▲/▼ buttons to turn the

ConnectedTM on/off.

ON  OFF

When ON is selected, controlling and

CRESTRON

managing the projector can be performed by using the controllers of Crestron connected to the same network. For the details of

EXTERNAL

CONTROL

Crestron Connected web site.

URL: http://www.crestron.com/

Use the ▲/▼ buttons to turn the Extron on/off.

ON  OFF

When ON is selected, the controllers of

Extron connected via HDBaseT the projector. For the details of Extron, visit

the following web site.

EXTRON *

URL: http://www.extron.com/

2. Connection to the network

Crestron

, visit the following

can detect

NOTE

when HDBaseT is selected in OPTION

- SERVICE - CONTROL TERMINAL -

WIRED NETWORK. (&OPTION menu

in the Operating Guide)

* CP-WU5505/CP-WX5505/CP-X5555 only

(continued on next page)

• This item is enabled only

Page 36

2. Connection to the network

Item Description

To use Network Presentation, an exclusive application is

required. It can be installed from the bundled application

CD. You can also download the latest version and relevant

information from the Hitachi website. Refer to 4. Network Presentation (

Network Presentation.

If you set a computer to the Presenter mode while its image is projected, the projector is occupied by the computer and access from any

QUIT

PRESENTER

MODE

other computer is blocked.

Use this function to quit the Presenter mode and

allow other computers to access the projector. Select this item to display a dialog. Press the ► button to choose OK in the dialog. The Presenter mode is cancelled and a message is displayed indicating the result.

If you set one or more computers to the Multi

OTHER

OPERATION

PC mode and send their images to the projector, you can select the display mode on the projector from two options below.

- Single PC mode: displays the image of the selected computer on full screen.

- Multi PC mode: displays the images sent from

up to four computers on screen that is divided

into quarter sections.

MULTI PC

MODE

Select this item to display a dialog.

Use the dialog to change the display mode as

explained below.

• To change from Multi PC mode to Single PC

mode, select one of computers in the dialog

using the ▲/▼/◄/► buttons and press the

ENTER or INPUT button.

Press the ► button to choose OK, and then

press ENTER or INPUT again. The image for the selected computer is displayed on full screen.

(continued on next page)

&78) for the details of

(continued on next page)

Page 37

Item Description

• To change from Single PC mode to Multi PC

mode, press the ► button to choose OK in the

dialog and press the ENTER or INPUT button. The display mode is changed.

• The Presenter mode setting

of the selected computer

becomes valid when the

display mode is changed to Single PC mode. Also, the

Presenter mode setting becomes invalid when

OTHER

OPERATION

(continued)

MULTI PC

MODE

(continued)

the display mode is changed to Multi PC mode, regardless of the setting on the computers.

DISPLAY

USER

NAME

Selecting this item displays the user name. This function helps you identify from which computer the current image is sent.

2. Connection to the network

Page 38

3. Web Control

You can adjust or control the projector via a network from a web browser on a

computer connected to the same network.

■Projector Web Control

You can control the projector, collect the status such as lamp time, and set e-mail or schedule, etc. in Projector Web Control.

Recommended web browser

･ Internet Explorer

9/ 10/ 11

NOTE

• Web browsers other than recommended ones may not work.

• If JavaScript® is disabled in your web browser conguration, you must enable JavaScript® in order to use the projector web pages properly. See the Help les for your web browser for details on how to enable JavaScript®.

• It is recommended that all web browser updates are installed.

• If data is transferred via wireless and wired LAN at the same time, the

projector may not process the data correctly.

■Crestron e-Control

　Crestron e-Control

is a control

interface using a web browser provided

by Crestron Electronics, Inc..

Crestron e-Control

can control and

monitor the projector.

(continued on next page)

Page 39

3. Web Control

NOTE

• Crestron e-Control® is created using Flash®. You need to install

Adobe® Flash® Player on your computer to use Crestron e-Control®. Crestron e-Control® is not displayed in a web browser that does not support Flash®.

• In any of the following cases, the selection window does not appear but the Login window of the Projector Web Control is displayed.

- Network Settings - Other Setup - Crestron e-Control is "Disable" (&46)

- Network Settings - Common Setup - Crestron is "OFF" (&43)

- NETWORK menu - EXTERNAL CONTROL - CRESTRON is "OFF" (&35)

Refer to the following for conguring or controlling the projector via a web browser. Make sure that your computer and the projector is connected via network, and

then start Web browser.

Enter the projector's IP address into URL input box of the Web browser as the

example below, and then press the Enter key or button. Example: If the IP address of the projector is set to 192.168.1.10:

Enter “http://192.168.1.10/” into the address bar of the web browser and press the Enter key or click

button.

If a correct URL is input, and the

projector and your computer are connected to the same network correctly, the selection window will be displayed.

NOTE

• Do not control the projector with the projector's menu or remote

control, and via Web Control at the same time. It may cause some operational

errors in the projector.

• The language used on the Projector Web Control is the same as that of the

OSD on the projector. If you want to change it, you need to change the OSD language on the projector. (&SCREEN menu in the Operating Guide)

Page 40

3. Web Control

3.1 Projector Web Control

3.1.1 Login

To use the Projector Web Control function, you need to login with your user name and password.

Below are the factory default settings for user

name and password.

User name Administrator

Password <blank>

Enter your user name and password, and then click the [OK]. If you login successfully, the screen below will be displayed.

Main menu

Click the desired operation or conguration item on the main menu.

Page 41

3.1 Projector Web Control (continued)

3.1.2 Network Information

Displays the projector’s current network

conguration settings.

Item Description

Common Information

Projector Name Displays the projector name settings.

Wireless Information Displays the current settings of wireless LAN.

Wireless Network Displays the ON/OFF of Wireless Network. Mode Displays the mode of wireless LAN communication.

DHCP Displays the DHCP setting.

IP Address Displays the IP address.

Subnet Mask Displays the subnet mask.

Default Gateway Displays the default gateway. DNS Server Address Displays the DNS server address.

MAC Address Displays the MAC address.

SSID Displays the SSID used by the projector. SSID Broadcast Displays the SSID Broadcast used by the projector.

Encryption Displays the data encryption setting. Channel Displays the channel used for wireless LAN. Speed Displays the current wireless LAN transmission speed.

Wired Information Displays the current wired LAN settings.

DHCP Displays the DHCP setting.

IP Address Displays the IP address.

Subnet Mask Displays the subnet mask.

Default Gateway Displays the default gateway. DNS Server Address Displays the DNS server address.

MAC Address Displays the MAC address.

Displays information common to both wireless and wired LAN.

3. Web Control

Page 42

3. Web Control

3.1 Projector Web Control (continued)

3.1.3 Network Settings

Displays and congures network settings.

Item Description

Common Setup

Wireless Network Switches ON/OFF of wireless network function.

Projector Name

sysLocation (SNMP)

sysContact (SNMP)

AMX D.D. (AMX Device Discovery)

Congures the settings common to wireless and wired LAN.

Congures the name of the projector.

The length of the Projector Name can be up to 64 alphanumeric characters. Only alphabets, numbers and following symbols can be used.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space.

Particular projector name is pre-assigned by default.

Congures the location to be referred to when using SNMP. The length of the sysLocation can be up to 255 alphanumeric

characters. Only numbers ‘0-9’, alphabet ‘a-z’ and ‘A-Z’ can

be used.

Congures the contact information to be referred to when

using SNMP. The length of the sysContact can be up to 255 alphanumeric characters. Only numbers ‘0-9’, alphabet ‘a-z’ and ‘A-Z’ can

be used.

Congures the AMX Device Discovery setting to detect the projector from the controllers of AMX connected to the same network. For the details of AMX Device Discovery, visit the AMX web site.

URL: http://www.amx.com

(continued on next page)

Page 43

3.1 Projector Web Control - Network Settings (continued)

Item Description

Common Setup (continued)

Crestron

Extron *

Congures the settings common to wireless and wired LAN.

Congures the Crestron setting to detect the projector from

the controllers of Crestron connected to the same network.

For the details of Crestron, visit the Crestron web site.

URL: http://www.crestron.com

Congures the Extron setting to detect the projector from the controllers of Extron connected to the same network via

HDBaseT

web site.

URL: http://www.extron.com

NOTE

selected in OPTION - SERVICE - CONTROL TERMINAL-

WIRED NETWORK.

port. For the details of Extron, visit the Extron

• This item is enabled only when HDBaseT is

(&OPTION menu in the

Operating Guide)

Wireless Setup Congures the wireless LAN settings.

Select "Simple Access Point" or "Infrastructure".

3. Web Control

NOTE

Mode

Encryption Lock

* CP-WU5505/CP-WX5505/CP-X5555 only

(continued on next page)

to be able to use wireless LAN. In the meantime, the

operating speed of the projector may be decreased and NETWORK INFORMATION may not be displayed correctly.

Permits or inhibits changes of the following settings related to wireless connection.

Mode

･

SSID

･

SSID Broadcast

･

Encryption

･

Encryption key (WEP key, WPA passphrase)

･

When Encryption Lock is set to ON, these settings cannot be

changed by the menu of the projector.

NOTE

is performed only when it can be connected without changing the current settings.

• When switching MODE, it takes 60 seconds

• If Encryption Lock is ON, wireless connection

Page 44

3. Web Control

3.1 Projector Web Control - Network Settings (continued)

Item Description

Wireless Setup (continued)

Simple Access Point settings

IP Conguration Congures network settings.

IP Address Congures the IP address. Subnet Mask Subnet mask of the projector is xed to 255.255.255.0.

SSID

SSID Broadcast

Encryption Select data encryption method.

WPA Passphrase

Channel

Congures the wireless LAN settings.

Congures Simple Access Point mode.

Input SSID. The maximum number of input characters is 32. Only alphabets, numbers and the following symbols can be used.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space.

Default setting of SSID in Simple Access Point mode is [SimpleAccessPoint].

Change default setting before use not to overlap. Select SSID Broadcast.

Set this function to OFF when making SSID of a projector not to be displayed in wireless connection list of the computer.

Input WPA Passphrase.

Available number of input characters is 8 to 63. Only

alphabets, numbers and the following symbols can be used.

!"#$%&'()*+,-./:;<=>?@ [\]^_`{|}~ and space

Select from “1” to “11”, a channel to use in the Simple Access Point mode.

NOTE

country. In addition, depending on the country or region, it may be required to use a wireless network card that

conforms to the standards in the respective country or

region.

• The channels may vary depending on the

(continued on next page)

Page 45

3.1 Projector Web Control - Network Settings (continued)

Item Description

Wireless Setup (continued)

Infrastructure settings

IP Conguration Congures network settings.

DHCP ON Enables DHCP.

DHCP OFF Disables DHCP.

IP Address Congures the IP address when DHCP is disabled.

Subnet Mask

Default Gateway

DNS Server Address

SSID

Encryption Select data encryption method.

WEP Key

WPA Passphrase

Congures the wireless LAN settings.

Congures Infrastructure mode.

Congures the subnet mask when DHCP is disabled.

Congures the default gateway when DHCP is disabled.

Congures the DNS server address.

Select an SSID from the list. If you require to set your unique SSID, select [Custom], then set your own SSID following the rules below. The maximum number of input characters is 32. Only alphabets, numbers and the following symbols can be used.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space.

Input the WEP key. Either ASCII characters or hexadecimal numbers can be

used during WEP key input. However, you cannot use a combination of both.The length of the key is dened as

follows according to the WEP and character formats.

Encryption ASCII characters HEX numbers WEP 64bit 5 characters 10 characters

WEP 128bit 13 characters 26 characters

Input WPA Passphrase.

Available number of input characters is 8 to 63. Only

alphabets, numbers and the following symbols can be used.

!"#$%&'()*+,-./:;<=>?@ [\]^_`{|}~ and space

3. Web Control

(continued on next page)

Page 46

3. Web Control

3.1 Projector Web Control - Network Settings (continued)

Item Description

Wired Setup Congures the wired LAN settings.

IP Conguration Congures network settings.

DHCP ON Enables DHCP.

DHCP OFF Disables DHCP.

IP Address Congures the IP address when DHCP is disabled. Subnet Mask Congures the subnet mask when DHCP is disabled.

Default Gateway

DNS Server Address Congures the DNS server address.

Other Setup Congures other network settings.

Crestron e-Control

Congures the default gateway when DHCP is disabled.

Set whether or not to use Crestron e-Control

If you choose Disable, not the selection window but the Login window of Projector Web Control will be displayed at rst.

Click the [Apply] button to save the settings.

NOTE

• The new conguration settings are activated after restarting the

network connection. When the conguration settings are changed, you must

restart the network connection. You can restart the network connection from Network Restart on the main menu. (&67)

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

• The WEP Key, WPA passphrase and SSID settings will not be set if the invalid

characters are used.

• The projector does not allow both wireless and wired LAN to be connected to

the same network. Do not set the same network address for both wireless and

wired LAN.

Page 47

3.1 Projector Web Control (continued)

3.1.4 Port Settings

Displays and congures communication port

settings.

Item Description

Network Control Port1 (Port:23)

Port open Click the [Enable] check box to use port 23.

Authentication

Network Control Port2 (Port:9715)

Port open Click the [Enable] check box to use port 9715.

Authentication

PJLinkTM Port (Port:4352)

Port open Click the [Enable] check box to use port 4352.

Authentication

My Image Port (Port:9716)

Port open Click the [Enable] check box to use port 9716.

Authentication

Messenger Port (Port:9719)

Port open Click the [Enable] check box to use port 9719.

Authentication

Congures command control port 1 (Port:23).

Click the [Enable] check box when authentication is required for this port.

Congures command control port 2 (Port:9715).

Click the [Enable] check box when authentication is required for this port.

Congures the PJLink

port (Port:4352).

Click the [Enable] check box when authentication is required for this port.

Congures the My Image Port (Port:9716).

Click the [Enable] check box when authentication is required for this port.

Congures the Messenger Port (Port:9719).

Click the [Enable] check box when authentication is required for this port.

3. Web Control

(continued on next page)

Page 48

3. Web Control

3.1 Projector Web Control - Port Settings (continued)

Item Description

SNMP Port Congures the mib le port.

Port open Click the [Enable] check box to use SNMP.

Congures the destination of the SNMP Trap in IP format.

Trap address

Download MIB le Downloads a MIB le from the projector.

Network Bridge Port Congures the Bridge port number.

Port number

• The address allows not only IP address but also domain name if the valid DNS server is setup in the Network

Settings. The maximum length of host or domain name is up to 255 characters.

Input the port number. Except for 41794, 9715, 9716, 9719, 9720, 5900, 5500, 4352 between 1024 and 65535 can be set up. It is set to 9717 as the default setting.

Click the [Apply] button to save the settings.

NOTE

• The new conguration settings are activated after restarting the

network connection. When the conguration settings are changed, you must

restart the network connection. You can restart the network connection from Network Restart on the main menu. (&67)

Page 49

3.1 Projector Web Control (continued)

3.1.5 Mail Settings

Displays and congures e-mail addressing

settings.

Item Description

Send Mail

Authentication

SMTP Server Congures the SMTP server.

Server address

Port number

POP Server Congures the POP server.

Server address

Port number

Click the [Enable] check box to use the e-mail function. Congure the conditions for sending e-mail under the Alert Settings.

Selects the authenticaton method.

Enter the user name of the SMTP server or POP server as the user

name.

Enter the password of the SMTP server or POP server as the

password. The maximum number of input characters is 63. Only alphabets, numbers and the following symbols can be used.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space.

Congures the SMTP server address.

• The address allows not only IP address but also domain name if the valid DNS server is setup in the Network Settings. The maximum

length of host or domain name is up to 255 characters.

Alphanumeric characters, "-", or "." can be used. Congures the port number of the SMTP server.

It is set to 25 as the default setting.

Congures the POP server address.

• The address allows not only IP address but also domain name if the valid DNS server is setup in the Network Settings. The maximum

length of host or domain name is up to 255 characters.

Alphanumeric characters, "-", or "." can be used. Congures the port number of the POP server.

It is set to 110 as the default setting.

3. Web Control

(continued on next page)

Page 50

3. Web Control

3.1 Projector Web Control - Mail Settings (continued)

Item Description

Sender E-mail address

Recipient E-mail address

Send Test Mail Sends a test e-mail to the set address.

Congures the sender e-mail address.

The length of the sender e-mail address can be up to 255 alphanumeric characters.

Congures the e-mail address of up to ve recipients. You

can also specify the [to] or [cc] for each address. The length of the recipient e-mail address can be up to 255 alphanumeric characters.

Click the [Apply] button to save the settings.

Mail settings are initialized when clicking the [Reset] button.

NOTE

• You can conrm whether the mail settings work correctly by using the

[Send Test Mail] button. Enable Send Mail setting before clicking the [Send Test Mail].

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

Page 51

3. Web Control

3.1 Projector Web Control (continued)

3.1.6 Alert Settings

Displays and congures failure & alert settings.

Notication such as e-mail and SNMP trap can be set regarding the following

errors/warnings.

　･Cover Error 　･Fan Error 　･Lamp Error 　･Temp Error 　･Air Flow Error 　･Cold Error 　･Filter Error 　･Shade Error 　･AC Blackout Error 　･Other Error 　･Schedule Execution Error 　･Lamp Time Alarm 　･Filter Time Alarm 　･Transition Detector Alarm 　･Cold Start 　･Authentication Failure

Refer to Chapter 8-1 for the details of the above errors/warnings. (

90)

Page 52

3. Web Control

3.1 Projector Web Control - Alert Settings (continued)

The Alert Items are shown below.

Item Description

Alarm Time

SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts.

Send Mail

Mail Subject

Mail Text

Congures the time to alert.

(Only Lamp Time Alarm and Filter Time Alarm.)

Click the [Enable] check box to enable e-mail alerts. (Except Cold Start and Authentication Failure.)

Congures the subject line of the e-mail to be sent.

The length of the subject line can be up to 100 alphanumeric

characters. Using any other character may shorten the

subject line. (Except Cold Start and Authentication Failure.)

Congures the text of the e-mail to be sent.

The length of the text is up to 1024 alphanumeric characters.

Using any other character may shorten the text.

(Except Cold Start and Authentication Failure.)

Click the [Apply] button to save the settings. The settings are initialized when clicking the [Reset] button.

Page 53

3.1 Projector Web Control (continued)

3.1.7 Schedule Settings

Displays and congures schedule settings.

3. Web Control

1) Schedule Management

Item Description

Sunday

Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Specic date No.1

Specic date No.2

Specic date No.3

Specic date No.4

Specic date No.5

Specic date No.6

Specic date No.7

Specic date No.8

Specic date No.9

Specic date No.10

NOTE

• Be sure to set the date and time

before enabling scheduled events. (&57)

• Refer to 8.3 Event Scheduling for the details

of schedule settings. (&95)

Schedule settings executed on each day of the week.

Schedule settings executed on specied day. Up to 10 days can be specied.

Page 54

3. Web Control

3.1 Projector Web Control - Schedule Settings (continued)

Item Description

Schedule

Program

Select the checkbox of the schedule to execute.

Select the program. The detail of the event registered in each program can be conrmed in the program list displayed at

the bottom of the screen.

Date (Month/Day)

Input the date (month/day) when the schedule is executed for

Specic date 1~10.

Click the [Apply] button to save the settings. Click the [Refresh] button to update the screen to the latest status. Click the [Program Edit] button to display the program edit of the selected program. Click the [Copy to] button to copy the content of the program from which you copy (the list on the left) to the program to which you copy (the list on the right). The same program No. cannot be selected for both the program from which and the program to which you copy.

Page 55

3.1 Projector Web Control - Schedule Settings (continued)

2) Program Edit

The current event settings are displayed on the list. To add additional functions and events, set

the following items.

3. Web Control

NOTE

• A maximum of 16 programs of

schedule can be set. A maximum of 20 events

can be registered in 1 program.

Item Description

Time Congures the time to execute events. Event [Parameter] Congures the events to be executed.

Power

Congures the parameters for power control.STANDBY

Input Source

COMPUTER IN

HDMI 1/MHL

HDMI 2

HDBaseT*

VIDEO

LAN

My Image

IMAGE-OFF

IMAGE-1

IMAGE-2

IMAGE-3

IMAGE-4

Congures the parameters for switching input.

Congures the parameters for My Image data display.

* CP-WU5505/CP-WX5505/CP-X5555 only

Page 56

3. Web Control

3.1 Projector Web Control - Schedule Settings (continued)

Item Description

Messenger

TEXT-OFF

TEXT-1

TEXT-2

TEXT-3

TEXT-4

TEXT-5

TEXT-6

TEXT-7

TEXT-8

TEXT-9

TEXT-10

TEXT-11

TEXT-12

Eco Mode

ECO

Blank

Congures the parameters for Messenger data display.

Congures the parameters for eco mode switching.NORMAL

Congures the parameters for blank screen on/off control.OFF

Click the [Register] button to add new events to the program. Click the [Delete] button to delete events from the program. Click the [Delete All] button to clear all the events registered in the current selected program. Click the [Back] button to go back to the schedule management screen.

Page 57

3. Web Control

3.1 Projector Web Control (continued)

3.1.8 Date/Time Settings

Displays and congures the date and time

settings.

Item Description

Current Date Congures the current date in year/month/day format. Current Time Congures the current time in hour:minute:second format.

Daylight Savings Time

Start Congures the date and time daylight savings time begins.

Month Congures the month daylight savings time begins (1~12).

Week

Day

Time

End Congures the date and time daylight savings time ends.

Month Congures the month daylight savings time ends (1 ~ 12).

Week

Day

Time

hour Congures the hour daylight savings time begins (0 ~ 23). minute Congures the minute daylight savings time begins (0 ~ 59).

hour Congures the hour daylight savings time ends (0 ~ 23). minute Congures the minute daylight savings time ends (0 ~ 59).

Click the [ON] check box to enable daylight savings time and set the following items.

Congures the week of the month daylight savings time begins (First, 2, 3, 4, Last).

Congures the day of the week daylight savings time begins

(Sun, Mon, Tue, Wed, Thu, Fri, Sat).

Congures the week of the month daylight savings time ends (First, 2, 3, 4, Last).

Congures the day of the week daylight savings time ends

(Sun, Mon, Tue, Wed, Thu, Fri, Sat).

(continued on next page)

Page 58

3. Web Control

3.1 Projector Web Control - Date/Time Settings (continued)

Item Description

Time difference

SNTP Server

SNTP

Address

Cycle

Congures the time difference. Set the same time difference

as the one set on your computer. If unsure, consult your IT manager.

Congures the SNTP server address in IP format.

• The address allows not only IP address but also domain name if the valid DNS server is setup in the Network

Settings. The maximum length of host or domain name is up to 255 characters.

Congures the interval at which to retrieve Date and Time information from the SNTP server (hour:minute).

Click the [Apply] button to save the settings.

NOTE

• The new conguration settings are activated after restarting the

network connection. When the conguration settings are changed, you must

restart the network connection. You can restart the network connection from Network Restart on the main menu. (&67)

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

• To enable the SNTP function, the time difference must be set.

• The projector will retrieve Date and Time information from the time server and override time settings when SNTP is enabled.

•

The internal clock’s time may not remain accurate. Using SNTP is recommended

to maintain accurate time.

• The internal battery is required to be replaced when the time is off soon after

setting date and time.

Page 59

3.1 Projector Web Control (continued)

3.1.9 Security Settings

Displays and congures passwords and other

security settings.

Item Description

User Account Congures the user name and password.

User name

Password

Re-enter Password Reenter the above password for verication.

Network Control

Authentication Password

Re-enter Authentication Password

Network Presentation

Authentication Password

Re-enter Authentication Password

Congures the user name.

The length of the text can be up to 32 alphanumeric characters.

Congures the password.

The length of the text can be up to 255 alphanumeric characters.

Congures the Authentication password for Network Control Port1 (Port: 23), Network Control Port2 (Port: 9715),

PJLink™ Port (Port: 4352), My Image Port (Port: 9716), and

Messenger Port (Port: 9719). (

Congures the Authentication password.

The length of the text can be up to 32 alphanumeric characters.

Reenter the above password for verication.

Setting an authentication password used in Network Presentation.The authentication function is disabled when an authentication password is not set.

Congures the Authentication password.

The length of the text can be up to 15 alphanumeric characters.

Reenter the above password for verication.

&47)

3. Web Control

(continued on next page)

Page 60

3. Web Control

3.1 Projector Web Control - Security Settings (continued)

Item Description

SNMP Congures the community name if SNMP is used.

Community name

Congures the community name. The length of the text can

be up to 64 alphanumeric characters.

Click the [Apply] button to save the settings.

NOTE

• The new conguration settings are activated after restarting the

network connection. When the conguration settings are changed, you must

restart the network connection. You can restart the network connection from Network Restart on the main menu. (&67)

• Only numbers ‘0-9’, alphabet ‘a-z’ and ‘A-Z’ can be used.

Page 61

3.1 Projector Web Control (continued)

3.1.10 Projector Control

Operations of the projector can be performed with the items on the screen. The categories of the items are shown in the main menu. Most of the items have a submenu. Refer to the table below for details.

3. Web Control

NOTE

• The setting value may not match with the actual value if the user

changes the value manually. In that case, refresh the page by clicking the

[Refresh] button.

Item

POWER INPUT SOURCE BLANK ON/OFF MUTE FREEZE

MAIN

(continued on next page)

MAGNIFY MAGNIFY POSITION V MAGNIFY POSITION H TEMPLATE SHADE

[ON]: closed / [OFF]: opened

Page 62

3. Web Control

3.1 Projector Web Control - Projector Control (continued)

Item

WINDOW CONFIGURATION - OFF / PbyP / PinP

Click the [Apply] button to execute after selecting the display mode (OFF/

MAIN (continued)

PICTURE

IMAGE

INPUT

(continued on next page)

PbyP/ PinP) from the dropdown list. Click the [Edit] button to display the screen for detailed settings while PbyP or PinP display mode.

MY IMAGE MY IMAGE DELETE

PICTURE MODE GAMMA

PICTURE QUALITY

BRIGHTNESS CONTRAST COLOR TINT SHARPNESS ACTIVE IRIS MY MEMORY ASPECT

The selected parameter cannot be set depending on the input signal. OVER SCAN V POSITION H POSITION H PHASE H SIZE AUTO ADJUST EXECUTE PROGRESSIVE VIDEO NR COLOR SPACE VIDEO FORMAT DIGITAL FORMAT DIGITAL RANGE COMPUTER IN FRAME LOCK MHL STANDBY PWR.

COLOR TEMP ACCENTUALIZER HDCR

Page 63

3.1 Projector Web Control - Projector Control (continued)

Item

KEYSTONE V KEYSTONE H

MODE BLENDING LEVEL BLENDING REGION CROPPING DIMMING LEVEL WHITE BALANCE GAIN WHITE BALANCE OFFSET ECO MODE FILTER MESSAGE

SETUP

KEYSTONE

PERFECT FIT SETUP - Corner Position/Line Distortion WARPING MODE

EDGE BLENDING

LAMP & FILTER

IMAGE OPTIMIZER PICTURE POSITION INSTALLATION

STANDBY MODE

NOTE

• The network function is not available when STANDBY

MODE is set to SAVING and the projector is in standby mode. Connect the projector to the network after setting STANDBY MODE to NORMAL.

3. Web Control

OSD MESSAGE HDMI OUTPUT STANDBY OUTPUT VOLUME

AUDIO

(continued on next page)

SPEAKER AUDIO SOURCE

Page 64

3. Web Control

3.1 Projector Web Control - Projector Control (continued)

Item

LANGUAGE Click the [Apply] button to switch the language on the Web screen

according to the setting of the selected language in the projector.

MENU POSITION V MENU POSITION H

BLANK

SCREEN

OPTION

SERVICE

* CP-WU5505/CP-WX5505/CP-X5555 only

AUTO BLANK START UP MyScreen Lock TEMPLATE C.C. - DISPLAY C.C. - MODE C.C. - CHANNEL SOURCE SKIP AUTO SEARCH DIRECT POWER ON AUTO POWER OFF SHADE TIMER MY BUTTON – 1 / 2 / 3 / 4 REMOTE RECEIV.* REMOTE FREQ. REMOTE ID HDMI OUT RESOLUTION Quit Presenter Mode

Quit compulsorily from the Presenter mode. Refer to Chapter 4 for the details of Presenter Mode.

(

&78

)

Page 65

3.1 Projector Web Control (continued)

3.1.11 Remote Control

The functions on the bundled remote control are assigned to the Web Remote Control screen. Do not control the projector with the projector's

remote control and via Web Remote Control at

the same time. It may cause some operational errors in the projector.

(STANDBY/ON)

•

• COMPUTER IN

• HDMI 1 / MHL

• HDMI 2

• HDBaseT (CP-WU5505/CP-WX5505/CP-X5555 only)

• VIDEO

• LAN

• BLANK

• MUTE

• FREEZE

• ▲/ ▼/ ◄ / ►

• ENTER

• MENU

• RESET

3. Web Control

NOTE

• One operation can be executed only with one click. The button should

be clicked repeatedly to operate continuously.

• When clicking the button repeatedly, some commands may not be sent correctly. Click it at intervals.

•

When the button is pushed, a message window comes up to conrm the

operation. To control the power, push [OK], otherwise push [Cancel].

Page 66

3. Web Control

3.1 Projector Web Control (continued)

3.1.12 Projector Status

Displays the current settings and status of the projector.

Item Description

Error Status Displays the error status.

Lamp Time Displays the usage time for the lamp. Filter Time Displays the usage time for the lter.

Power Status Displays the power status.

Input Status Displays the input signal source. Blank On/Off Displays the Blank screen on/off status.

Mute Displays the Mute on/off status. Freeze Displays the Freeze status.

Shade Displays the Shade status.

Page 67

3.1 Projector Web Control (continued)

3.1.13 Network Restart

Restarts the projector’s network connection.

Item Description

Restart

Restarts the projector’s network connection in order to

activate new conguration settings.

3. Web Control

NOTE

• Restarting requires you to re-login in order to further control or

congure the projector via a web browser. Wait 30 seconds or more after

clicking the [Restart] button to log on again.

Page 68

3. Web Control

3.1 Projector Web Control (continued)

3.1.14 Connection Test

Checks if the network is connecting to DNS

server or SNTP server, etc.

Item Description

Destination IP Address

Click the [Execute] button to test the connection after entering IP address to connect to.

Display example of the connection succeeded ：

Display example of the connection failed ：

•

NOTE

Conrm information of the target IP address with network administrator.

• Connection test may result in an error even if the connection is performed

properly when the packets for checking the connection are discarded before

arriving at the target depending on the settings of rewall or packet ltering, etc.

• The result of the connection test is displayed only in English.

Page 69

3.2 Crestron e-Control

The Main window as shown above is displayed at rst. However, if you have enabled User Password on the Tools window

(&73), a dialog prompting you to enter the password as shown on the right will be displayed, and no operation is enabled until

you have entered the password. After entering

the preset password, the dialog disappears and the Main window will be displayed. As shown below, you can open a window by clicking the corresponding tab at the top right of the window.

3. Web Control

Tab

User Password dialog

Tab Description

Logs out from e-Control

Logout

Tools Opens Tools window. ( Info Opens Info window. ( Contact IT Help Opens Help Desk window. (

This tab appears only when User Password of the Tools window is

enabled.

&73)

&75)

&76)

Page 70

3. Web Control

3.2 Crestron e-Control

(continued)

NOTE

• In any of the following cases, the selection window does not appear

but the Login window of the Projector Web Control is displayed.

- Network Settings - Other Setup - Crestron e-Control is "Disable" (&46)

- Network Settings - Common Setup - Crestron is "OFF" (&43)

- NETWORK menu - EXTERNAL CONTROL - CRESTRON is "OFF" (&35)

Set Crestron to on and enable Crestron e-Control, then close the web browser. Next, restart the web browser, followed by entering the projector's IP address.

• Only English is supported on Crestron e-Control®.

• If the connection is terminated, the "Loading..." screen will appear. Check the

connection between the projector and the computer, then return or refresh the Web page.

• The control from Crestron e-Control® is supported only via wired LAN.

Page 71

3.2 Crestron e-Control® (continued)

3.2.1 Main window

3. Web Control

You can operate the basic controls of the projector on this screen.

NOTE

• If the projector is in the standby mode, only the [Power] button can

be operated.

1. Click a button and operate as follows.

Button Description

Power Turns the power on/off. Vol - / Vol + Adjusts the volume setting. Mute Turns Mute on/off.

2. Sources List

You can click a button to switch the input channel. The cursor will move

according to the currently selected input port.

Button Description

Computer In Selects input from COMPUTER IN port. HDMI 1 / MHL Selects input from HDMI 1 / MHL port. HDMI 2 Selects input from HDMI 2 port. HDBaseT * Selects input from HDBaseT port. Video Selects input from VIDEO port. LAN Selects input from LAN port.

* CP-WU5505/CP-WX5505/CP-X5555 only

Page 72

3. Web Control

3.2 Crestron e-Control® - Main window (continued)

3. Click a button and operate as follows. To show the hidden buttons, click the ◄ / ► icons at the left and right ends.

Button Description

Freeze Turns Freeze on/off. Contrast Adjusts the contrast setting. Brightness Adjusts the brightness setting. Color Adjusts the color setting. Sharpness Adjusts the sharpness setting.

Magnify

Auto Performs the automatic adjustment. Blank Turns the BLANK screen on/off.

Controls the magnication setting using the [+] / [-] buttons. Use the [▲] [▼] [◄] [►] buttons to move to the area you want

to magnify.

4. Click the button and operate in the same way as the bundled remote control.

Button Description

Menu Assigned the same operation as MENU button. Enter Assigned the same operation as ENTER button. Reset Assigned the same operation as RESET button.

▲ Assigned the same operation as ▲ button.

▼ Assigned the same operation as ▼ button. ◄ Assigned the same operation as ◄ button. ► Assigned the same operation as ► button.

Page 73

3.2 Crestron e-Control® (continued)

3.2.2 Tools window

3. Web Control

Congures the settings between the projector and Crestron

control system.

Click the [Exit] button to return to the Main window.

NOTE

• If two-byte characters are used, the input text or numbers cannot be

set correctly.

• Any items on this window cannot be left blank.

1. Crestron Control

Congures the settings of Crestron

Item Description

IP Address Congures the IP address of the control system. IP ID Congures the IP ID of the control system.

Port

Species the port number used for communication by the

control system.

control system devices.

To apply the settings, click the [Send] button.

2. Projector

Congures the network settings of the projector.

Item Description

Projector Name

Location

Assigned To:

Congures the name of the projector. The length of the

Projector Name can be up to 64 alphanumeric characters.

Congures the location name of the projector. You can specify a Location name up to 32 alphanumeric characters.

Congures the user name for the projector. You can specify a

user name up to 32 alphanumeric characters.

The usable symbols are space and the following:

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~

To apply the settings, click the [Send] button.

Page 74

3. Web Control

3.2 Crestron e-Control® - Tools window (continued)

2. Projector (continued)

Congures the network settings of the projector.

Item Description

DHCP Enables DHCP. IP Address Congures the IP address when DHCP is disabled. Subnet Mask Congures the subnet mask when DHCP is disabled. Default Gateway Congures the default gateway when DHCP is disabled. DNS Server Congures the DNS server address when DHCP is disabled.

To apply the settings, click the [Send] button.

3. User Password

Congures the User Password. To prompt the entry of User Password before

starting e-Control

Item Description

New Password

Conrm

, select the checkbox.

Congures the password.

You can specify a password up to 26 alphanumeric characters. The usable symbols are space and the following:

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ Reenter the above password for verication. If the password is

incorrect, an error message is displayed.

To apply the settings, click the [Send] button.

4. Admin Password

Congures the Admin Password. To prompt the entry of Admin Password before

displaying the Tools window, select the checkbox.

Item Description

Congures the password.

New Password

Conrm

You can specify a password up to 26 alphanumeric characters. The usable symbols are space and the following:

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ Reenter the above password for verication. If the password is

incorrect, an error message is displayed.

To apply the settings, click the [Send] button.

Page 75

3.2 Crestron e-Control® (continued)

3.2.3 Info window

1 2

Displays the current settings and status of the projector. Click the [Exit] button to return to the Main window.

1. Projector Information

Item Description

Projector Name Displays the projector name settings. Location Displays the location name of the projector. MAC Address Displays the wired LAN MAC address of the projector.

Resolution

Lamp Hours Displays the usage time for the lamp. Assigned To: Displays the user name for the projector.

Displays the resolution and vertical frequency of the signal input

selected on the projector.

3. Web Control

2. Projector Status

Item Description

Power Status Displays the power status.

Input Source Displays the input signal source.

Picture Mode Displays the picture mode setting.

Installation Displays the installation setting.

Eco Mode Displays the eco mode setting.

Error Status Displays the error status.

NOTE

• Projector Name, Location and the user name for Assigned To: may

appear truncated if they are too long.

Page 76

3. Web Control

3.2 Crestron e-Control® (continued)

3.2.4 Help Desk window

Sends/receives messages to/from the administrator for Crestron RoomView Express and Fusion RV®.

Button Description

Send Sends a message.

Checks the received message.

Page 77

3. Web Control

3.2 Crestron e-Control® (continued)

3.2.5 Emergency Alert

When the administrator for Crestron RoomView

Express and Fusion RV® sends

out an alert message, it will be displayed on the screen.

You can reply to the alert message via a chat format. Input a message in the box

below the alert message, and click the [Send] button.

NOTE

• For details of Emergency Alert, refer to the manual of Crestron

RoomView® Express or Fusion RV®.

• The alert message from Crestron RoomView® and Fusion RV® is displayed

on the screen of the projector in the way similar to the real-time text of the Messenger function. (&83) If another real-time text is displayed on the screen,

it will be overwritten by the alert message. However, if the priority of the real-

time text is set to high, the alert message does not appear on the screen. For details, refer to the manual for the application of the Messenger.

Page 78

4. Network Presentation

4.1 Outline

The projector can display or play back the computer screen images and audio data that are transmitted through the network. This Network Presentation feature helps you to smoothly make your presentations and conduct conferences.

To use Network Presentation, an exclusive application, "LiveViewer" is required. It can be installed from the bundled application CD.

For details of Network Presentation and instructions to install the "LiveViewer", refer to the manual for "LiveViewer".

NOTE

• The use of "LiveViewer" function depends on the model you are using. If you want to use the latest "LiveViewer", please refer to the appropriate group item in the "LiveViewer" User's Manual. This model will be in the Group

of H.

•

For Mac user, download the software from the website. Refer to 2.5. Applications.

Page 79

4. Network Presentation

4.2 Display Mode

LiveViewer has two display modes, Single PC mode and Multi PC mode.

4.2.1 Single PC mode

The Single PC mode can display images in full screen from one computer to the

projector/switcher via wireless LAN or wired LAN.

■ Presenter Mode

In the Single PC mode, the projector can be occupied by one computer and can block access from any other computers (if Presenter Mode is set to ON in

LiveViewer). While making your presentation, you don’t need to worry that the

image on screen will be unexpectedly switched to an image sent by another

computer. Presenter Mode can be set to ON in the option menu in the LiveViewer.

4.2.2 Multi PC mode

The projector can display images of up to four computers connected at the same time.

Page 80

4. Network Presentation

4.3 Multi Projector Mode

In the Multi Projector/Multi Display mode, up to 12 projectors or switchers

connected to projectors can connect with the computer via wireless or wired LAN

simultaneously.

This function is for Windows users only.

4.4 Moderator Control Mode

One computer can be assigned as Moderator (Host) to control all other computers

(Clients) or the switchers connected with the projector via wireless LAN or wired LAN. Since Clients cannot control the LiveViewer and the projector, the Host can

proceed with the program as arranged smoothly and safely.

LAN

This function is for Windows users only.

Moderator (Host)

Clients

Page 81

4. Network Presentation

4.5 Port Number

The port numbers used for LiveViewer are shown below.

Port No. Protocol 5500 TCP 5900 TCP 9720 TCP

NOTE

• When other application uses the ports above, LiveViewer and Projector Quick

Connection may not work.

Page 82

5. MyImage Function

5. My Image Function

The projector can display still images transferred via the network. It is possible to allocate up to 4 image les.

MY IMAGE transmission requires an exclusive application for your computer. Use the application to transfer the image data.

For information on the necessary settings and operations for the computer and projector, refer to the manual for the application.

To display the transferred image, select the MY IMAGE item in the NETWORK menu. For more information, please see the description of the MY IMAGE item of

the NETWORK menu.

NOTE

• Using MY BUTTON registered as MY IMAGE can display transferred image. (&OPTION menu in the Operating Guide)

• The image le also can be displayed by using schedule function from the web

browser.(&95)

•

If data is transferred via wireless and wired LAN at the same time, the projector

may not be able to process the data correctly

Page 83

6. Messenger Function

6.1 Outline

The projector can display text data transferred via the network on the screen and

play back audio data inside the projector. The text data can be displayed on the screen in two ways. One is to display the text transferred from the computer on real time, and the other is to choose the text data stored in the projector and display it. It is possible to store up to 12 text data.

Transfer text data

Display text data (ex.

)

Page 84

6. Messenger Function

The chemical class

Today’s

Messenger function requires an exclusive application for your computer. To edit,

transfer and display the text data, use the application.

For information on the necessary settings and operations for the computer and projector, refer to the manual for the application.

6.2 Supported Languages

The languages that can be displayed by Messenger function are shown below.

English, French, German, Spanish, Italian, Norwegian, Dutch, Portuguese, Swedish, Finnish, Danish, Brasileiro, Indonesian, Lithuanian, Estonian, Latvian, Polish, Czech, Hungarian, Slovenian, Croatian, Russian, Turkish, Greek, Japanese, Simplied Chinese, Traditional Chinese, Korean, Vietnamese

6.3 Display Style

There are 4 types of message display style. The following is the description of each type.

1) Scroll The message scrolls to the left in the message display area.

2) Box (Scroll up)

The message scrolls upwards in the square message display area.

Page 85

3) Pop on

The message is displayed in full view in the

square message display area.

4) Picture Side The message is displayed in the message display area on the right or left.

This style is available only for WXGA and WUXGA model projector.

6. Messenger Function

NOTE

• Using MY BUTTON registered as MESSENGER can turn the displaying messenger text on/off. (&OPTION menu in the Operating Guide)

• The text le also can be displayed by using schedule function via the web

browser. (&95)

•

If data is transferred via wireless and wired LAN at the same time, the projector

may not process the data correctly.

Page 86

7. Network Bridge Function

232C communication using the projector as a network terminal.

Protocol change

WIRELESS port

(USB wireless adapter)

CONTROL port

Serial data

RS-232C

RS-232C cable

External device

LAN port

Computer

TCP/IP data

Wired LAN

LAN cable

Wireless

LAN

HDBaseT port

(CP-WU5505/CP-WX5505/ CP-X5555 only)

7.1 Connecting devices

1) Connect the projector’s LAN port to the computer’s LAN port with a LAN cable, or insert the USB wireless adapter into the WIRELESS port.

2) Connect the projector’s CONTROL port and the device’s RS-232C port with an RS-232C cable, for RS-232C communication.

NOTE

ensure the connection. each port and use the suitable cable. (&Connection to the ports in the Operating

Guide - Technical)

• When to HDBaseT, connect LAN cable to HDBaseT port on the projector.

• Before connecting the devices, read the manuals for the devices to For RS-232C connection, check the specications of

OPTION - SERVICE - CONTROL TERMINAL - WIRED NETWORK is set

Page 87

7. Network Bridge Function

7.2 Communication setup

To congure the setup of the communication using NETWORK BRIDGE for the projector, use items in the COMMUNICATION menu. Open the menu of the projector and select the OPTION - SERVICE - COMMUNICATION menu. (&OPTION menu > SERVICE > COMMUNICATION in the Operating Guide)

1) In the COMMUNICATION TYPE menu, select NETWORK BRIDGE (WIRELESS or WIRED depending on the type of connection you use) for the

CONTROL port.

2) Using the SERIAL SETTINGS menu, select the proper baud rate and parity for the CONTROL port, according to the specication of the RS-232C port of the connected device.

Item Condition

BAUD RATE 4800bps/9600bps/19200bps/38400bps

PARITY NONE/ODD/EVEN

Data length 8 bit (xed)

Start bit 1 bit (xed)

Stop bit 1 bit (xed)

3) Using the TRANSMISSION METHOD menu, set up the proper method for the

CONTROL port according to your use.

NOTE

• The OFF is selected for the COMMUNICATION TYPE as the default

setting.

• Using the COMMUNICATION menu, set up the communication. Remember

that an unsuitable setup could cause malfunction of communication.

• When either one of the NETWORK BRIDGE settings is selected in the COMMUNICATION TYPE menu, RS-232C commands cannot be received from

the CONTROL port.

•

When COMMUNICATION TYPE is set to other than OFF, the setting of OPTION

- SERVICE - CONTROL TERMINAL - RS-232C is forcibly set to CONTROL.

7.3 Communication port

For the NETWORK BRIDGE function, send the data from the computer to the projector with using the Network Bridge Port congured in the Port Settings of

web browser. (

NOTE

between 1024 and 65535 can be set up as the Network Bridge Port number. It is set to 9717 as the default setting.

&47)

• Except for 41794, 9715, 9716, 9719, 9720, 5900, 5500, 4352

Page 88

7. Network Bridge Function

7.4 Transmission method

The transmission method can be selected from the menus, only when the

NETWORK BRIDGE is selected for the COMMUNICATION TYPE.

&OPTION menu > SERVICE > COMMUNICATION in the Operating Guide)

(

HALF-DUPLEX  FULL-DUPLEX

7.4.1 HALF-DUPLEX

This method lets the projector make two way communication, but only one

direction, either transmitting or receiving data, is allowed at a time. The method does not allow the projector to receive the data from the computer while waiting for response data from an external device. After the projector receives the response data from an external device or the response limit time is past, the projector can receive the data from the computer. That means that the projector controls transmitting and receiving the data to synchronize the communication.

To use the HALF-DUPLEX method, set up the RESPONSE LIMIT TIME following

the instructions below.

TCP/IP data Serial data

Wired LAN

LAN cable

Computer

Wireless LAN

Transmitting data

Discarding data

Response data

Protocol change

Response limit time

RS-232C

RS-232C cable

Transmitting data

Response data

Discarding data

External device

Using the RESPONSE LIMIT TIME menu, set the waiting time for response data from an external device. (

&OPTION menu > SERVICE > COMMUNICATION in

the Operating Guide)

OFF  1s  2s  3s ( OFF)

Page 89

7.4 Transmission method (continued)

7. Network Bridge Function

NOTE

• With using the HALF-DUPLEX method, the projector can send out

254 byte data at the maximum at a time.

• If it is not required to monitor the response data from an external device and the RESPONSE LIMIT TIME is set to OFF, the projector can receive the data from the computer and send it out to an external device continuously.

The OFF is selected as the default setting.

7.4.2 FULL-DUPLEX

This method lets the projector make two way communication, transmitting and

receiving data at the same time, without monitoring response data from an external device. With using this method, the computer and an external device will send the data out of synchronization. If it is required to synchronize them, set the computer to make the synchronization.

NOTE

When the computer controls the synchronization of receptions and transmissions,

• the external device may not be controlled properly depending on the status of data

processing of the projector.

Page 90

8. Other Functions

8.1 E-mail Alerts

The projector can automatically send an alert message to the specied e-mail

addresses when the projector detects a certain condition that is requiring maintenance or detected an error.

NOTE

• The projector may be not able to send e-mail if the projector suddenly loses

power.

•

Mails may not be sent correctly depending on the mail environment you are

using.

Alerts available to E-mail alerts are as follows.

Cover Error The lamp cover has not been properly xed. Fan Error The cooling fan is not operating.

Lamp Error

Temp Error

Air Flow Error The internal temperature is rising.

Cold Error

Filter Error Filter time over.

Shade Error The shade does not work correctly. AC Blackout Error Power supply was interrupted momentarily.

Other Error

Schedule Execution Error

Lamp Time Alarm Lamp Time has exceeded the specied alarm limit. Filter Time Alarm Filter Time has exceeded the specied alarm limit.

Transition Detector Alarm

(continued on next page)

• Up to ve e-mail addresses can be specied.

Item Description

The lamp does not light, and there is a possibility that interior portion has become heated.

There is a possibility that the interior portion has become heated.

There is a possibility that the interior portion has

become overcooled.

Errors other than the above.

If this error is displayed, please contact your dealer.

Failed to execute scheduled events.

Transition Detector Alarm. ( Operating Guide)

&SECURITY menu in the

Page 91

8. Other Functions

NOTE

• The timing of receiving Filter Error e-mail is depending on the FILTER

MESSAGE setting in the LAMP & FILTER item of the SETUP menu which determines the period until the lter message is displayed on the projector screen. An e-mail will be sent when the usage time of the lter exceeds the set time limit. No notication e-mail will be sent if the FILTER MESSAGE is set to OFF. (&SETUP menu in the Operating Guide)

• Lamp Time Alarm is a threshold for e-mail notication of the lamp time. When the set time exceeds the limit congured in the Projector Web Control,

an e-mail will be sent.

•

Filter Time Alarm is a threshold for e-mail notication of the lter time. When

the set time exceeds the limit congured in the Projector Web Control, an e-mail

will be sent.

Page 92

8. Other Functions

To use the projector’s e-mail alert function, please congure the following items

through a web browser.

Mail Settings (

&49)

1) Select [Mail Settings] on main menu in Projector Web Control.

2) Congure each item in Mail Settings page. Refer to item 3.1.5 Mail Settings

(

&49) for further information.

3) Click the [Apply] button to save the settings.

4) Click the [Send Test Mail] button to conrm that the e-mail settings are

correct.

The following mail will be delivered to the specied addresses.

Subject line : Test Mail <Projector name>

Text : Send Test Mail

Date <Testing date> Time <Testing time> IP Address <Projector IP address> MAC Address <Projector MAC address>

Alert Settings (

&51)

1) Select [Alert Settings] on main menu in Projector Web Control.

2) Select and congure each alert item. Refer to item 3.1.6 Alert Settings (

&51)

for further information.

3) Click the [Apply] button to save the settings.

Failure/Warning e-mails are formatted as follows:

Subject line : <Mail title> <Projector name> Text : <Mail text> Date <Failure/Warning date> Time <Failure/Warning time> IP Address <Projector IP address> MAC Address <Projector MAC address>

Page 93

8. Other Functions

8.2 Projector Management using SNMP

The SNMP (Simple Network Management Protocol) enables to manage the projector information, which is a failure or warning status, from the computer on the network.

NOTE

• It is recommended that SNMP functions are executed by a network

administrator.

• SNMP management software must be installed on the computer to monitor the projector via SNMP.

Standard MIB (MIB-2)

You can refer the following items dened in system group of Standard MIB (MIB-2).

Item Description

sysName Projector name is set. sysLocation The information on where it is located. It has character string

sysContact The information on the administrator's contact information. It

set in sysLocation (SNMP) in Projector Web Control - [Network

Settings] - [Common Setup].

has character string set in sysContact (SNMP) in Projector Web Control - [Network Settings] - [Common Setup].

Enhanced MIB

You can get conguration information by using Enhanced MIB for projectors. Enhanced MIB for projectors can be downloaded from [Port Settings] page in

Projector Web Control.

Trap

When an error or warning occurs in the projector, a notication can be sent to the specied address.

In addition to e-mail alert shown in 8.1 Email Alerts (

&90), the following

notication can be sent.

Item Description

Cold Start When the projector is supplied with the power, it works as

Authentication Failure The SNMP access is detected from the invalid SNMP

below.

• If the STANDBY MODE is set to the NORMAL: the projector's

power status changes from “OFF” to “Standby state”.

• If the STANDBY MODE is set to the SAVING: the projector's

power status changes from “Standby state” to “ON (lamp is turned on)”. (

SETUP menu in the Operating Guide).

community.

Page 94

8. Other Functions

Setup the following functions through WEB browser, if you want to manage the

projector by SNMP.

Port Settings (

&47)

1) Select [Port Settings] on main menu in Projector Web Control.

2) Click the [Download MIB le] to download a MIB le.

3) Click the [Enable] check box to open the SNMP Port. Set the address to send

the SNMP trap to when a Failure/Warning occurs.

Security Settings (&59)

1) Select [Security Settings] on main menu in Projector Web Control.

2) Click the [SNMP] and set the community name on the screen that is displayed.

Alert Settings (&51)

Congure the settings for Trap transmission of Failures/Warnings.

1) Select [Alert Settings] on main menu in Projector Web Control.

2) Select the Failure/Warning item to be congured.

3) Click the [Enable] check box to send out the SNMP trap for Failures/Warnings.

Clear the [Enable] check box when SNMP trap transmission is not required.

4) Click the [Apply] button to save the settings.

•

NOTE

• Be sure to execute Network Restart when the settings of [Port Settings] or

[Security Settings] is changed.

Page 95

8. Other Functions

8.3 Event Scheduling

The scheduling function enables to setup scheduled events including power on /

power off. It enables to be “self-management” projector.

Note the following before setting the schedule.

NOTE

• Schedule can also be set in OPTION - SCHEDULE menu of the

projector. (&Refer to Operating Guide – OPTION).

• A maximum of 16 programs of schedule can be set. A maximum of 20 events

can be registered in 1 program.

• No events are registered in program 1 – 16 with factory default settings. The program is required to be set in advance when using the schedule function for the rst time.

• The priority for scheduled events is as follows 1) specic date 2) weekly

• Up to 10 specic dates are available for scheduled events. Priority is given to those with the lower numbers when more than one event has been scheduled for the same date and time (e.g., ‘Specic date No. 1’ has priority over ‘Specic

date No. 2’ and so on.

• The power on event has the lowest priority among all the events that are set

at the same time.

• Be sure to set the date and time before enabling scheduled events. (&57)

• After the projector is moved, check the date and time set for the projector before conguring the schedules.

•

The internal clock’s time may not remain accurate. Using SNTP is recommended

to maintain accurate time.

• Certain error state in the projector (such as temperature error, lamp error) will prevent the projector from appropriate execution of scheduled functions/events.

• Events “My Image” and “Messenger” will not be executed appropriately and

result in “schedule execution error” status when the lamp does not light and/or data to be displayed are not stored in the projector at the time when scheduled

event is executed.

• Events “Input Source” and “My Image” is not executed if security function is

enabled and the projector is locked due to the function.

Page 96

8. Other Functions

The procedure to set the schedule in Projector Web Control is described in the following.

Setting the program is necessary to use the schedule function. Various events such as power on/off or switching input source, and the time to execute the events are to be registered in the program. No events are registered in program 1 – 16

with factory default settings. Set the program following the steps below. In the case that the program has already been set, skip to step 6).

1) Select [Schedule Settings] on main menu in Projector Web Control.

2) Select the program number in dropdown list under Program List and click the

[Program Edit] button to display the following program edit display. The display for editing Program-1 is shown below.

3) After setting the time, events and parameters, click the [Register] to add the

new event.

Click the [Delete] button when you want to delete an event. Click the [Delete All] button when you want to delete all the events in the currently selected program.

Page 97

8. Other Functions

4) When you want to edit the program with other number continuously, select the

program you want to edit in dropdown list and click the [Select] button to display the display for editing the selected program.

5) Click the [Back] button to go back to schedule management screen after

nishing the program setting.

The procedure to assign the program set in the step 1) ~ 5) to the schedule is

described in the following.

6) Click the checkbox of the schedule to be executed (e.g. Click the checkbox of

“Monday”, when it is to be executed on Mondays) in the schedule management screen.

7) Select the program to be executed in dropdown list. You can conrm the event

information registered in each program in the program list on the bottom of the screen.

When setting the Specic date No.1 ~ 10, enter the date (month/day).

8) Click the [Apply] button to save the schedule settings in the projector.

Repeat step 6) ~ 8) similarly to set the schedule you want to execute.

The schedule settings are now complete.

Finally, conrm the time stored in the projector is correctly set.

■How to copy the program

When you copy the currently selected program to other program, click the checkbox under icon. Click the [Copy to] button after selecting the program to which you want to copy in dropdown list.

The same program as the currently selected one cannot be specied as the

program to which you want to copy.

Page 98

8. Other Functions

8.4 Command Control via the Network

You can congure and control the projector via the network using RS-232C

commands.

Communication Port

The following two ports are assigned for the command control.

TCP #23 (Network Control Port1 (Port: 23)) TCP #9715 (Network Control Port2 (Port: 9715))

NOTE

Command Control Settings (

• Command control is available only via the specied port above.

&47)

Congure the following items from a web browser when command control is used.

Example: If the IP address of the projector is set to 192.168.1.10:

1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select Projector Web Control from the selection window.

2) Enter your user name and password, and then click the [OK].

3) Click the [Port Settings] on the main menu.

4) Click the [Enable] check box to open Network Control Port1 (Port: 23) to use TCP #23. Click the [Enable] check box for the [Authentication] setting when authentication is required, otherwise clear the check box.

5) Click the [Enable] check box to open Network Control Port2 (Port: 9715) to use TCP #9715. Click the [Enable] check box for the [Authentication] setting when authentication is required, otherwise clear the check box.

6) Click the [Apply] button to save the settings.

Page 99

8. Other Functions

8.4 Command Control via the Network (continued)

When the authentication setting is enabled, the following settings are required.

&59)

(

7) Click the [Security Settings] on the main menu.

8) Click the [Network Control] and enter the desired authentication password.

* See NOTE.

9) Click the [Apply] button to save the settings.

NOTE

• The Authentication Password will be the same for Network Control

Port1 (Port: 23), Network Control Port2 (Port: 9715), PJLink™ Port (Port:

4352), My Image Port (Port: 9716) and Messenger Port (Port: 9719).

• The new conguration settings are activated after restarting the network connection. When the conguration settings are changed, you must restart

the network connection. You can restart the network connection from Network Restart on the main menu. (&67)

Page 100

8. Other Functions

8.4 Command Control via the Network (continued)

Command Format

Command formats differ among the different communication ports.

● TCP #23

You can use the RS-232C commands without any changes. The reply data format is the same as the RS-232C commands. (

RS-232C Communication in

the Operating Guide - Technical) However, the following reply will be sent back in the event of authentication

failure when authentication is enabled.

Reply Error code

0x1F 0x04 0x00

● TCP #9715

Send Data format

The following formatting is added to the header (0 x 02), Data length (0 x 0D), Checksum (1 byte) and Connection ID (1 byte) of the RS-232C commands.

Header Data length RS-232Ccommand Check Sum

0x02 0x0D 13 bytes 1 byte 1 byte

Connection

Header → 0x02, Fixed Data length → RS-232C commands byte length (0x0D, Fixed) RS-232C command → RS-232C commands that start with 0xBE 0xEF

(13 bytes)

Check Sum → This is the value to make zero on the addition of the

lower 8 bits from the header to the checksum.

Connection ID → Random value from 0 to 255 (This value is attached

to the reply data)

100