Hitachi CP-X306, CP-X206 User Manual

Projector

CP-X206/CP-X306

User's Manual (detailed)
Operating Guide

Thank you for purchasing this projector.

WARNING

product. Be sure to read “Safety Guide” rst. After reading them, store them in a
safe place for future reference.

►Before using this product, please read all manuals for this

About this manual

Various symbols are used in this manual. The meanings of these symbols are
described below.

WARNING

CAUTION

NOTE

• The manufacturer assumes no responsibility for any errors that may appear in
this manual.

• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.

Trademark acknowledgment

• Mac is a registered trademark of Apple Inc.

• Microsoft and Windows are registered trademarks of Microsoft Corporation.

• VESA and DDC are trademarks of the Video Electronics Standard Association.

• PowerPC is a registered trademark of International Business Machines
Corporation.
All other trademarks are the properties of their respective owners.

• The information in this manual is subject to change without notice.

This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.

Please refer to the pages written following this symbol.



1

Contents

Contents



About this manual . . . . . . . . . . . 1

Contents .
Projector features . .
Preparations . .

. . . . . . . . . . . . . . . . . 2

. . . . . . . . . 3

. . . . . . . . . . . . . 3

Contents of package . . . . . . . . . . . . . 3

Fastening the lens cover . . . . . . . . . . 3

Part names .

. . . . . . . . . . . . . . . 4

Projector . . . . . . . . . . . . . . . . . . . . . . 4

Control panel . . . . . . . . . . . . . . . . . . . 5

Rear panel . . . . . . . . . . . . . . . . . . . . 5

Remote control . . . . . . . . . . . . . . . . . 6

Setting up .

. . . . . . . . . . . . . . . . 7

Arrangement . . . . . . . . . . . . . . . . . . . 7

Connecting your devices . . . . . . . . . 10

Connecting power supply .

. . . . . . . 12

Using the security bar and slot . . . . 12

Remote control . .

. . . . . . . . . . 13

Installing the batteries . . . . . . . . . . . 13

About the remote control signal .
Changing the frequency of remote control signal
Using as a simple PC mouse & keyboard

Power on/off .

. . . . . . . . . . . . . 15

. . 14

. . 14

Turning on the power . . . . . . . . . . . 15

T

urning off the power . . . . . . . . . . . 15

Oper

ating .

. . . . . . . . . . . . . . . 16

Adjusting the volume . . . . . . . . . . . . 16

T

emporarily muting the sound . . . . . 16

Selecting an input signal
Searching an input signal .
Selecting an aspect ratio

. . . . . . . . . 16

. . . . . . . 17

. . . . . . . . . 17

Adjusting the projector's elevator .
Adjusting the zoom and focus
Using the automatic adjustment feature

. . . . . 18

. . . 19

Adjusting the position . . . . . . . . . . . 19

Correcting the keystone distortions

Using the magnify feature . . . . . . . . 20

Freezing the screen .

. . . . . . . . . . . 21

Temporarily blanking the screen . . . 21

Using the menu function . . . . . . . . 22

EASY MENU.

. . . . . . . . . . . . . . 24

Aspect, Auto keystone execute,
k

eystone

c

ontrAst, color, tint, shArpness,

W

hisper, mirror, reset, Filter time,

l

AnguAge,

, picture mode, Brightness,

Go to Advanced Menu

...

PICTURE menu . . . . . . . . . . . . 26

IMAGE menu . . . . . . . . . . . . . . 29

INPUT menu . . . . . . . . . . . . . . 31

SETUP menu . . . . . . . . . . . . . . 34

AUDIO menu . . . . . . . . . . . . . . 36

SCREEN menu . . . . . . . . . . . . . 37

. . 13

OPTION menu . . . . . . . . . . . . . 41

NETWORK menu . . . . . . . . . . . 54

C.C. (closed caption) menu . . 59

. 18

Maintenance . . . . . . . . . . . . . . 60

. . 20

Troubleshooting .

Specications . .



Brightness, contrAst, gAmmA,
c

olor temp, color, tint, shArpness,

m

y memory

Aspect, over scAn, v position,
h

position, h phAse, h size,

A

uto Adjust execute

progressive, video nr, color spAce,
c

omponent, video FormAt, FrAme lock,

c

omputer in, resolution

Auto keystone execute,
k

eystone

s

tAndBy mode, monitor out

, Whisper, mirror,

volume, speAker, Audio

lAnguAge, menu position, BlAnk,
s

tArt up,

m

essAge, source nAme, templAte

M

yScreen

, M

yScreen Lock

,

Auto seArch, Auto keystone ,
A

uto on, Auto oFF, lAmp time,

F

ilter time, my Button,

m

y source, service, security

setup, projector nAme, my imAge,
i

nFormAtion, service

displAy, mode, chAnnel

Replacing the lamp . . . . . . . . . . . . . 60

Cleaning and replacing the air lter . . 62
Replacing the internal clock battery . . 64

Other care . . . . . . . . . . . . . . . . . . . . 65

. . . . . . . . . . 66

Related messages . . . . . . . . . . . . . 66

Regarding the indicator lamps . . . . 67

Shutting the projector down . . . . . . 68

Resetting all settings . . . . . . . . . . . . 68

Phenomena that may be easy

to be mistaken for machine defects

. . 69

. . . . . . . . . . . 72

2

Projector features / Preparations

Projector features

The projector provides you with the broad use by the following features.

ü This projector has a variety of I/O ports that supposedly cover for any

business scene.

ü This projector realizes the large projection image, even if in a small space.
ü The new double layer lter system is expected to function longer and offers

you less maintenance frequency.

ü This projector can be controlled and monitored via LAN connection.

Preparations

Contents of package

Please see the “Contents of package” section in the User’s Manual (concise)
which is a book. Your projector should come with the items shown there. Contact
immediately your dealer if anything is missing.

NOTE

to use the original packing materials when moving the projector. Use special
caution for the lens.

• Keep the original packing materials, for future reshipment. Be sure

Fastening the lens cover

To avoid losing the lens cover, please fasten the lens
cover to the projector using the enclosed strap.

Fix the strap to the strap hole of the lens cover.

1.

Thread one end of the strap through the strap hole
of the lens cover and make the loop at the end,
and let the other end of the strap through the loop.
Not have a knot in the strap at either end.

Fix the strap to the strap hole of the projector.

2.

Thread the other end of the strap through the strap hole of the projector and
make the loop there. Let the lens cover with the one end of strap though the
loop.

3

Part names

Part names

Projector

(1) Lamp cover (60)

The lamp unit is inside.
(2) Focus ring (
(3) Zoom ring (
(4) Control panel (
(5) Elevator buttons (x 2) (
(6) Elevator feet (x 2) (
(7) Remote sensor (
(8) Lens (
(9) Lens cover (
(10) Intake vents
(11)

Filter cover (
The air lter and intake vent are

inside.
(12) Speaker (
(13) Exhaust vent
(14) AC IN
(15) Power switch (
(16) Rear panel (
(17) Security bar (
(18) Security slot (
(19) Slot cover (

The internal clock battery is
inside.

18)

18)

65)

3)

62)

36)

(AC inlet) (

5)



5)

18)

13)

12)

15)

12)
12)

64)

18)

(6)

(9)

HOT!

(19)

(18)

HOT!

(8)

(13)

(16)

(1) (2) (3) (4)

(7)

(6)

(4)

(17)

(13)

(6)

(1)

(5)

(12)

(11)

(10)

(6)

(10)

(11)

(14)

(15)

WARNING

►HOT! : Do not touch around the lamp cover and the exhaust
vents during use or just after use, since it is too hot.
►Do not look into the lens or vents while the lamp is on, since the strong light is
not good for your eyes.
►Do not handle the elevator buttons without holding the projector, since the
projector may drop down.

CAUTION

►Maintain normal ventilation to prevent the projector from
heating up. Do not cover, block or plug up the vents. Do not place anything that
can stick or be sucked to the vents, around the intake vents. Clean the air lter
periodically.
►Do not use the security bar and slot to prevent the projector from falling down,
since it is not designed for it.

4

Part names

BATTERY

Control panel

(1) STANDBY/ON button (15)
(2) INPUT button (
(3) MENU button (

It consists of four cursor buttons.
(4) POWER indicator (
(5) TEMP indicator (
(6) LAMP indicator (

16, 22)

22)

15, 67)

67)

67)

Rear panel (10)

(1) AUDIO IN1 port
(2) AUDIO IN2 port
(3) AUDIO OUT port
(4) COMPUTER IN1 port
(5) COMPUTER IN2 port
(6) MONITOR OUT port
(7) Shutdown switch (
(8) CONTROL port

68)

(9) USB port
(10) COMPONENT

(Y, Cb/Pb, Cr/Pr) ports
(11) VIDEO port
(12) S-VIDEO
(13) AUDIO IN3 (L,R) ports
(14) LAN port

(1)

(3) (4) (7)

(14)

(6)
(5)
(4)

(1) (2)(3)

port

(6)(5)

(10)

(9)(8) (11)

(12)(13)

CAUTION

(2)

►Use the shutdown switch only when the projector is not
turned off by normal procedure, since pushing this switch stops operation of the
projector without cooling it down.

5

Part names

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

MENU

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

Remote control

(1) VIDEO button (17)
(2) COMPUTER button (
(3) SEARCH button (
(4) STANDBY/ON button (
(5) ASPECT button (
(6) AUTO button (
(7) BLANK button (
(8) MAGNIFY - ON button (
(9) MAGNIFY - OFF button (

16)

17)

15)

17)

19)

21)

20)

14, 20)

(10) MY SOURCE/DOC.CAMERA button (
(11) VOLUME - button (
(12) PAGE UP button (
(13) PAGE DOWN button (
(14) VOLUME + button (
(15) MUTE button (
(16) FREEZE button (
(17) MY BUTTON - 1 button (
(18) MY BUTTON - 2 button (
(19) KEYSTONE button (
(20) POSITION button (
(21) MENU button (
(22) ▲/▼/◄/► cursor buttons (
(23) ENTER button (
(24) ESC button (
(25) RESET button (
(26) Battery cover (

16)

14)

14)

16)

16)

21)

43)
43)

20)

19, 22)

22)

14, 22, 23)

14, 22, 23)

14, 22)

14, 22, 23)

13)

43)

(2)
(1)
(6)
(5)
(16)
(8)
(9)
(19)
(17)
(20)
(22)

(24)

(10)
(4)
(3)
(7)
(12)
(14)
(11)
(13)
(15)
(18)
(21)
(23)
(25)

(26)

Back of

the remote control

6

Setting up

Setting up

Install the projector according to the environment and manner the projector will be
used in.

Arrangement

Refer to the illustrations and tables below to determine screen size and projection distance.

<CP-X206>

The values shown in the table are calculated for a full size screen: 1024×768

a

Screen size (diagonal)

b

Projection distance (±10%)

c1 , c2 Screen height (±10%)

On a horizontal surface

Suspended from the ceiling

• Keep a space of 30 cm or more
between the sides of the projector
and other objects such as walls.

• Consult with your dealer before
a special installation such as
suspending from a ceiling.

a

Screen size

(diagonal)

inch m m inch m inch cm inch cm inch m inch m inch cm inch cm inch

30 0.8 0.9 34 1.1 41 41 16 5 2 1.0 38 1.1 45 39 15 -1 0
40 1.0 1.2 46 1.4 56 55 22 6 2 1.3 50 1.5 61 5
50 1.3 1.5 58 1.8 70 69 27
60 1.5 1.8 70 2.1 84 82 3
70 1.8 2.1 81 2.5 98
80 2.0 2.4 93 2.8 112 110 43 12 5 2.6 10

90 2.3 2.7 105 3.2 126 12
100 2.5 3.0 117 3.6 140 1
120 3.0 3.6 140 4.3 169 1
150 3.8 4.5 176 5.4 21
200 5.1 6.0 235 7.2 28
250 6.4 7.5 294 9.0 353
300 7.6 9.0 352 10.8 42

Projection distance

min. max. min. max.

4 : 3 screen 16 : 9 screen

b

c1 c2

Screen

height

96 38 11 4 2.3 89 2.7 107 90 35 -3 -1

3 49 14 5 2.9 115 3.5 138 116 46 -4 -1
37 54 15 6 3.2 127 3.9 153 129 51 -4 -2
65 65 18 7 3.9 153 4.7 184 154 61 -5 -2

1 206 81 23 9 4.9 192 5.8 230 193 76 -6 -2

2 274 108 30 12 6.5 256 7.8 307 257 101 -8 -3

343 135 38 15 8.1 320 9.8 384 322 127 -10 -4

3 411 162 46 18 9.8 384 11.7 461 386 152 -12 -5

Screen

height

8 3 1.6 63 1.9 76 64 25 -2 -1

2 9 4 1.9 76 2.3 91 77 30 -2 -1

b

Projection distance

2 3.1 122 103 41 -3 -1

c1

Screen

height

1 20 -2 -1

c2

Screen

height

7

Setting up

Arrangement (continued)

<CP-X306>

The values shown in the table are calculated for a full size screen: 1024×768

a

Screen size (diagonal)

b

Projection distance (±10%)

c1 , c2 Screen height (±10%)

On a horizontal surface

Suspended from the ceiling

• Keep a space of 30 cm or more
between the sides of the projector
and other objects such as walls.

• Consult with your dealer before
a special installation such as
suspending from a ceiling.

a

Screen size

(diagonal)

inch m m inch m inch cm inch cm inch m inch m inch cm inch cm inch

30 0.8 0.9 35 1.1 43 41 16 5 2 1.0 39 1.2 47 39 15 -1 0
40 1.0 1.2 47 1.4 57 55 22 6 2 1.3 52 1.6 62 5
50 1.3 1.5 59 1.8 71 69 27
60 1.5 1.8 71 2.2 86
70 1.8 2.1 83 2.5 100
80 2.0 2.4 95 2.9 115 1

90 2.3 2.7 107 3.3 129 12
100 2.5 3.0 119 3.6 144 1
120 3.0 3.6 143 4.4 17
150 3.8 4.6 179 5.5 216 2
200 5.1 6.1 239 7.3 288 2
250 6.4 7.6 299 9.1 360
300 7.6 9.1 359 11.0 432 4

Projection distance

min. max. min. max.

4 : 3 screen 16 : 9 screen

b

c1 c2

Screen

height

82 32 9 4 2.0 78 2.4 94 77 30 -2 -1
96 38 11 4 2.3 91 2.8 109 90 35 -3 -1

10 43 12 5 2.6 104 3.2 125 103 41 -3 -1

3 49 14 5 3.0 117 3.6 141 116 46 -4 -1

37 54 15 6 3.3 130 4.0 156 129 51 -4 -2

2 165 65 18 7 4.0 156 4.8 188 154 61 -5 -2

06 81 23 9 4.9 195 6.0 235 193 76 -6 -2
74 108 30 12 6.6 261 8.0 314 257 101 -8 -3

343 135 38 15 8.3 326 10.0 392 322 127 -10 -4

11 162 46 18 9.9 391 12.0 471 386 152 -12 -5

Screen

height

8 3 1.6 65 2.0 78 64 25 -2 -1

b

Projection distance

c1

Screen

height

1 20 -2 -1

c2

Screen

height

8

Arrangement (continued)

Setting up

WARNING

►Place the projector in a stable horizontal position. If the
projector falls or is knocked over, it could cause injury and/or damage to the
projector. Using a damaged projector could then result in re and/or electric
shock.

• Do not place the projector on an unstable, slanted or vibrational surface such

as a wobbly or inclined stand.

• Do not place the projector on its side, front or rear position.

• Consult with your dealer before a special installation such as suspending from

a ceiling or somewhere else.
►Place the projector in a cool place, and ensure that there is sufcient
ventilation. The high temperature of the projector could cause re, burns and/or
malfunction of the projector.

• Do not stop-up, block or otherwise cover the projector's vents.

• Keep a space of 30 cm or more between the sides of the projector and other

objects such as walls.

• Do not place the projector on metallic thing or anything weak in heat.

• Do not place the projector on carpet, cushions or bedding.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

• Do not place anything near the projector lens or vents, or on top of the

projector.

• Do not place anything that may be sucked into or stick to the vents on the

bottom of the projector. This projector has some intake vents also on the

bottom.
►Do not place the projector anyplace where it may get wet. Getting the projector
wet or inserting liquid into the projector could cause re, electric shock and/or
malfunction of the projector.

• Do not place the projector in a bathroom or the outdoors.

• Do not place anything containing liquid near the projector.

CAUTION

►Avoid placing the projector in smoky, humid or dusty place.
Placing the projector in such places could cause re, electric shock and/or
malfunction of the projector.

• Do not place the projector near humidiers, smoking spaces or a kitchen.
►Position the projector to prevent light from directly hitting the projector's remote
sensor.

9

Setting up

RGB IN

AUDIO IN

Y CB/PB CR/PR

COMPONENT VIDEO OUT

L R

AUDIO OUT

VIDEO OUT

L R

AUDIO OUT

L R

AUDIO OUT

S-VIDEO OUT

AUDIO OUT

RGB OUT

AUDIO OUT

USB

RGB OUT

LAN

RS-232C

Connecting your devices

Be sure to read the manuals for devices before connecting them to the projector.
Make sure that all the devices are suitable to be connected with this product, and
prepare the cables required to connect. Please refer to the following illustrations
to connect them.

PC

Speakers

(with an

amplier)

Monitor

VCR/DVD

player

WARNING

►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.

CAUTION

►Turn off all devices and unplug their power cords prior to
connecting them to projector. Connecting a live device to the projector may
generate extremely loud noises or other abnormalities that may result in
malfunction or damage to the device and the projector.
►Use appropriate accessory or designated cables. Ask your dealer about non­accessory cables which may be required a specic length or a ferrite core by
the regulations. For cables with a core only at one end, connect the end with the
core to the projector.
►Make sure that devices are connected to the correct ports. An incorrect
connection may result in malfunction or damage to the device and the projector.

10

Connecting your devices (continued)

Setting up

NOTE

projector, and make sure that all the devices are suitable to be connected with this
product. Before connecting to a PC, check the signal level, the signal timing, and the
resolution.

- Be sure to consult to the administrator of the network. Do not connect LAN
network that might have the excessive voltage.

- Some signal may need an adapter to input this projector

- Some PCs have multiple screen display modes that may include some signals which
are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA (1600X1200),
the signal will be converted to the projector’s panel resolution before being displayed.
The best display performance will be achieved if the resolutions of the input signal and
the projector panel are identical.

• While connecting, make sure that the shape of the cable's connector ts the port to

connect with. And be sure to tighten the screws on connectors with screws.

• When connecting a laptop PC to the projector, be sure to activate the PC’s external

RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT
display.) For details on how this is done, please refer to the instruction manual of the
corresponding laptop PC.

• When the picture resolution is changed on a PC depending on an input, automatic

adjustment function may take some time and may not be completed. In this case,
you may not be able to see a check box to select “Yes/No” for the new resolution on
Windows. Then the resolution will go back to the original. It might be recommended to
use other CRT or LCD monitors to change the resolution.

• In some cases, this projector may not display a proper picture or display any picture on

screen. For example, automatic adjustment may not function correctly with some input
signals. An input signal of composite sync or sync on G may confuse this projector, so
the projector may not display a proper picture.

• Be sure to read the manuals for devices before connecting them to the

port to any

.

About Plug-and-Play capability

Plug-and-Play is a system composed of a PC, its operating system and peripheral
equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and­Play can be used by connecting this projector to a PC that is VESA DDC (display data
channel) compatible.

• Take advantage of this feature by connecting an RGB cable to the COMPUTER IN1

port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of
connection is attempted.

• Please use the standard drivers in your PC as this projector is a Plug-and-Play monitor.

11

Setting up

Connecting power supply

At rst, make sure that the power switch of the
projector is set to OFF position (marked “O”).

Put the connector of the power cord into the

1.

AC IN (AC inlet) of the projector.
Firmly plug the power cord’s plug into the

2.

outlet.

AC IN Power cord

WARNING

incorrect or faulty connections may result in re and/or electrical shock.

• Only use the power cord that came with the projector. If it is damaged, consult
your dealer to get a new one.

• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.

• Never modify the power cord.

►Please use extra caution when connecting the power cord, as

Using the security bar and slot

Security slot

A commercial anti-theft chain or wire up to
10 mm in diameter can be attached to the
security bar on the projector.
Also this product has the security slot for the
Kensington lock.
For details, see the manual of the security
tool.

Anti-theft chain or wire

WARNING

from falling down, since it is not designed for it.

CAUTION

may become too hot.

►Do not use the security bar and slot to prevent the projector

►Do not place anti-theft chain or wire near the exhaust vents. It

Security bar

NOTE

measures. It is intended to be used as supplemental theft prevention measure.

12

• The security bar and slot is not comprehensive theft prevention

Remote control

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control
starts to malfunction, try to replace the batteries. If you will not use the remote control for
long period, remove the batteries from the remote control and store them in a safe place.

Holding the hook part of the battery

1.

cover, remove it.

Align and insert the two AA batteries

2.

(HITACHI MAXELL, Part No.LR6 or R6P)
according to their plus and minus terminals
as indicated in the remote control.
Replace the battery cover in the direction of the arrow and snap it back into place.

3.

WARNING

directed. Improper use may result in battery explosion, cracking or leakage,
which could result in re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specied. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.

• If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

►Always handle the batteries with care and use them only as

About the remote control signal

The remote control works with the projector’s remote
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range
when the sensor is active:
60 degrees (30 degrees to the left and right of the sensor)
within 3 meters about.

•

NOTE

If it is difcult to send the signal to the sensor directly, attempt to make the signal reect.

• The remote control uses infrared light to send signals to the projector (Class 1

LED), so be sure to use the remote control in an area free from obstacles that
could block the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun
light) or light from an extremely close range (such as from an inverter uorescent
lamp) shines on the remote sensor of the projector. Adjust the position of
projector avoiding those lights.

The remote control signal reected in the screen or the like may be available.

Approx.

3 m

30º

30º

13

Remote control

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

MENU

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

MENU

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal
frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control
does not function properly, attempt to change the signal frequency.
In order to set the Mode, please keep pressing the combination of
two buttons listed below simultaneously for about 3 seconds.

(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons

(2)

(2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons
Please remember that the REMOTE FREQ. in the SERVICE item of

the OPTION menu

(45)

of the projector to be controlled should be

set to the same mode as the remote control.

Using as a simple PC mouse & keyboard

The accessory remote control works as a simple mouse
and keyboard of the PC, when the projector's USB port
(B type) connects with the PC's USB port (A type) port
via a mouse cable.

(1) PAGE UP key: Press PAGE UP button.
(2) PAGE DOWN key: Press PAGE DOWN button.
(3) Mouse left button: Press ENTER button.
(4) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►.
(5) ESC key: Press ESC button.
(6) Mouse right button: Press RESET button.

USB port

(1)

(1)

(2)

WARNING

keyboard function could damage your equipment. While

►Improper use of the simple mouse &

(3)

using this function, please connect this product only
to a PC. Be sure to check your PC’s manuals before

(5)

connecting this product to the PC.

•

NOTE

When the simple mouse & keyboard function of this product does not work

correctly, please check the following.

- When a USB cable connects this projector with a PC having a built-in pointing device
(e.g. track ball) like a notebook PC, open BIOS setup menu, then select the external
mouse and disable the built-in pointing device, because the built-in pointing device may
have priority to this function.

- Windows 95 OSR 2.1 or higher is required for this function. And also this function may
not work depending on the PC’s congurations and mouse drivers.

- You cannot do things like press two buttons at once (for instance, pressing two buttons
at the same time to move the mouse pointer diagonally).

- This function is activated only when the projector is working properly. This function is
not available while the lamp is warming up (the POWER indicator blinks green), and
while adjusting the volume and display, correcting for keystone, zooming in on the
screen, using the BLANK function, or displaying the menu screen.

14

(4)

(6)

Power on/off

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

MENU

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯ONOFF

㧗

FREEZE

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARCH

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

1 2

ESC

ENTER

MENU

RESET

COMPUTER

Power on/off

Turning on the power

Make sure that the power cord is rmly and correctly

1.

connected to the projector and the outlet.
Remove the lens cover, and set the power switch to

2.

ON position (marked “ I ”).
The POWER indicator will light up in steady orange
(

67). Then wait several seconds because the

buttons may not function for these several seconds.
Press STANDBY/ON button on the projector or the

3.

remote control.
The projection lamp will light up and POWER indicator
will begin blinking in green. When the power is
completely on, the indicator will stop blinking and light
in steady green (

To display the picture, select an input signal according to the
section “Selecting an input signal”(

67).

16).

STANDBY/ON button
POWER indicator

Power switch

Turning off the power

Press the STANDBY/ON button on the projector or the remote control. The message

1.

“Power off?” will appear on the screen for about 5 seconds.
Press the STANDBY/ON button again while the message appears.

2.

The projector lamp will go off, and the POWER indicator will begin blinking in orange.
Then POWER indicator will stop blinking and light in steady orange when the lamp
cooling is complete (

Make sure that POWER indicator lights in steady orange, and set the

3.

power switch to OFF position (marked “O“).
POWER indicator will go off. Attach the lens cover.

Do not turn the projector on for about 10 minutes or more after turning it off.
Turning the projector on again too soon could shorten the lifetime of some
consumable parts of the projector.

67).

Power switch

WARNING

►A strong light is emitted when the projector’s power is on. Do
not look into the lens of the projector or look inside of the projector through any
of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just
after use, since it is too hot.

NOTE

• Turn the power on/off in right order. Please power on the projector

prior to the connected devices.

•

When the AUTO ON of the OPTION menu is set to the TURN ON, and the power
was turned off by the power switch last time, turning the power switch on makes
the projection lamp light on without pushing the STANDBY/ON button

• Use the shutdown switch (68) only when the projector is not turned off by
normal procedure.

(41).

15

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

MENU

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

MENU

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

MENU

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

Operating

Adjusting the volume

Use the VOLUME +/VOLUME - buttons to adjust the volume.

1.

A dialog will appear on the screen to aid you in adjusting the volume.
If you do not do anything, the dialog will automatically disappear after
a few seconds.

●

When is selected for current picture input port, the volume adjustment
is disabled. Please see AUDIO item of AUDIO menu

(36).

● When the projector is in the standby mode, the volume can be adjusted
if

is not selected for the AUDIO OUT STANDBY of AUDIO (36).

Temporarily muting the sound

Press MUTE button on the remote control.

1.

A dialog will appear on the screen indicating that you have muted the sound.
To restore the sound, press the MUTE, VOLUME + or VOLUME - button. Even if
you do not do anything, the dialog will automatically disappear after a few seconds.

●

●

When
muted. Please see AUDIO item of

is selected for current picture input port, the sound is always

AUDIO

menu

(36).

When the sound is muted while a signal from VIDEO(NTSC),
S-VIDEO(NTSC) or COMPONENT(480i@60)) port is selected, the C.C.
(Closed Caption) is automatically activated if the DISPLAY item of the C.C.
menu is set to AUTO and the input signal supports the C.C. feature

(59).

VOLUME +/- button

MUTE button

Selecting an input signal

Press INPUT button on the projector.

1.

Each time you press the button, the projector switches its input
port from the current port as below.

VIDEO  S-VIDEO  COMPONENT (Y, Cb/Pb, Cr/Pr)

● While TURN ON is selected for AUTO SEARCH item in OPTION
menu (
repeatedly till an input signal is detected.

Press COMPUTER button on the remote control.

1.

Each time you press the button, the projector switches its input
port from the current port as below.

COMPUTER IN 1  COMPUTER IN 2

● While TURN ON is selected for AUTO SEARCH item in OPTION
menu, the projector will keep checking every port sequentially till an
input signal is detected (
VIDEO, S-VIDEO or COMPONENT port is selected, the projector will
check COMPUTER IN1 port rst.

(continued on next page)

16

COMPUTER IN 1  COMPUTER IN 2

41), the projector will keep checking the ports in above order

INPUT button

COMPUTER button

41). If COMPUTER button is pushed when

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

MENU

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

MENU

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

Selecting an input signal (continued)

Press VIDEO button on the remote control.

1.

Each time you press the button, the projector switches its input

VIDEO button

port from the current port as below.

COMPONENT (Y, Cb/Pb, Cr/Pr)  S-VIDEO  VIDEO

●

While TURN ON is selected for AUTO SEARCH item in OPTION menu, the projector
will keep checking every port sequentially till an input signal is detected (

41). If

VIDEO button is pushed when COMPUTER IN1 or COMPUTER IN2 port is selected,
the projector will check COMPONENT port rst.

Searching an input signal

Press SEARCH button on the remote control.

1.

The projector will start to check its input ports as below in order to

SEARCH button

nd any input signals.
When an input is found, the projector will stop searching and
display the image. If no signal is found, the projector will return to
the state selected before the operation.

COMPUTER IN 1  COMPUTER IN 2

VIDEO  S-VIDEO  COMPONENT (Y, Cb/Pb, Cr/Pr)

● While TURN ON is selected for AUTO SEARCH item in OPTION menu (41), the
projector will keep checking the ports in above order repeatedly till an input signal is
detected.

Selecting an aspect ratio

Press ASPECT button on the remote control.

1.

Each time you press the button, the projector switches the mode
for aspect ratio in turn.

 For a computer signal

NORMAL  4:3  16:9  SMALL

 For a video signal, s-video signal or component video

signal

4:3  16:9  14:9  SMALL

 For no signal

4:3 (xed)

● ASPECT button does not work when no proper signal is inputted.

● NORMAL mode keeps the original aspect ratio setting.

ASPECT button

17

Operating

Adjusting the projector's elevator

When the place to put the projector is slightly uneven to the left or right, use the
elevator feet to place the projector horizontally.
Using the feet can also tilt the projector in order to project at
a suitable angle to the screen, elevating the front side of the
projector within 10 degrees.
This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is adjustable
while pushing the elevator button on the same side as it.

Holding the projector, push the elevator buttons to loose the elevator feet.

1.

Position the front side of the projector to the desired height.

2.

Release the elevator buttons in order to lock the elevator feet.

3.

After making sure that the elevator feet are locked, put the projector down

4.

gently.

If necessary, the elevator feet can be manually twisted to make more precise

5.

adjustments. Hold the projector when twisting the feet.

To loose an elevator foot, push the

elevator button on the same side as it.

CAUTION

projector, since the projector may drop down.
►Do not tilt the projector other than elevating its front within 10 degrees using
the adjuster feet. A tilt of the projector exceeding the restriction could cause
malfunction or shortening the lifetime of consumables, or the projector itself.

►Do not handle the elevator buttons without holding the

To nely adjust, twist the foot.

Adjusting the zoom and focus

Use the zoom ring to adjust the screen size.

1.

Use the focus ring to focus the picture.

2.

18

Focus ring

Zoom ring

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

MENU

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

MENU

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

Using the automatic adjustment feature

Press AUTO button on the remote control.

1.

Pressing this button performs the following.

 For a computer signal

The vertical position, the horizontal position and the
horizontal phase will be automatically adjusted.
Make sure that the application window is set to its maximum
size prior to attempting to use this feature. A dark picture
may still be incorrectly adjusted. Use a bright picture when
adjusting.

 For a video signal and s-video signal

The video format best suited for the respective input signal will be selected
automatically. This function is available only when the AUTO is selected for
the VIDEO FORMAT item in the INPUT menu (

32). The vertical position

and horizontal position will be automatically set to the default.

 For a component video signal

The vertical position, horizontal position and horizontal phase will be
automatically set to the default.

● The automatic adjustment operation requires approx. 10 seconds. Also
please note that it may not function correctly with some input. When this
function is performed for a video signal, a certain extra such as a line may
appear outside a picture.

● The items adjusted by this function may vary when the FINE or DISABLE is
selected for the AUTO ADJUST item of the SERVICE item in the OPTION
menu (

44).

AUTO button

Adjusting the position

Press POSITION button on the remote control when no menu

1.

is indicated.
The “POSITION” indication will appear on the screen.

Use the ▲/▼/◄/► cursor buttons to adjust the picture position.

2.

When you want to reset the operation, press RESET button on
the remote control during the operation.
To complete this operation, press POSITION button again.
Even if you do not do anything, the dialog will automatically
disappear after a few seconds.

When this function is performed on a video signal, s-video signal or component

●
video signal, some image such as an extra-line may appear at outside of the picture.

●

When this function is performed on a video signal, s-video signal or component
video signal, the range of this adjustment depends on OVER SCAN in IMAGE menu
(29)

setting. It is not possible to adjust when OVER SCAN is set to 10.

● If POSITION button is pressed when a menu is indicated on screen, the displayed
picture does not move its position but the menu does.

POSITION button

19

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

Correcting the keystone distortions

Press KEYSTONE button on the remote

1.

control. A dialog will appear on the screen to

KEYSTONE button

aid you in correcting the distortion.

Use the ▲/▼ cursor buttons to select AUTO or MANUAL

2.

operation, and press the ► button to perform the
following.

(1) AUTO executes automatic vertical keystone correction.
(2) MANUAL displays a dialog for keystone correction.

Use the ▲/▼ buttons for adjustment.

To close the dialog and complete this operation, press KEYSTONE button again. Even
if you do not do anything, the dialog will automatically disappear after a few seconds.

●

The adjustable range of this correction will vary among inputs. For some input, this function may not work well.

● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if

the projector screen is inclined or angled downward, this function may not work correctly.

●

When the zoom adjustment is set to the TELE (telephoto focus), the automatic keystone
distortion correction may be excessive. This function should be used when the zoom
adjustment is set to the full WIDE (wide-angle focus) whenever possible.

●

When the projector is placed on the level (about ±3°), the automatic keystone distortion correction may not work.

● When the projector is inclined to near ±30 degree or over, this function may not work well.

● This function will be unavailable when Transition Detector is on

Using the magnify feature

Press the ON button of MAGNIFY on the remote control.

1.

The “MAGNIFY” indication will appear on the screen and the

(50)

.

MAGNIFY
ON/OFF button

projector will go into the MAGNIFY mode. When the ON button of
MAGNIFY is pressed rst after the projector is started, the picture

will be zoomed twice. The indication will disappear in several
seconds with no operation.

Use the ▲/▼ cursor buttons to adjust the zoom level. The picture of

2.

video, s-video or component video signal can be zoomed in up to 2
times, and the picture of computer signal can be zoomed in up to 4 times.
To move the zoom area, press the POSITION button in the MAGNIFY mode, then use
the ▲/▼/◄/► cursor buttons to move the area. And to nalize the zoom area, press
the POSITION button again.
To exit from the MAGNIFY mode and restore the screen to normal, press the OFF
button of MAGNIFY on the remote control.

● The projector automatically exits from the MAGNIFY

mode when the input signal is

changed or when the display condition is changed.

● In the MAGNIFY

mode, the keystone distortion condition may vary, it will be restored

when the projector exits from the MAGNIFY mode.

NOTE

nd the level you want.

20

• The zoom level can be nely adjusted. Closely watch the screen to

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

MENU

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

MENU

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

Freezing the screen

Press the FREEZE button on the remote control.

1.

The “FREEZE” indication will appear on the screen (however,
the indication will not appear when the TURN OFF is selected
for the MESSAGE item in the SCREEN menu (

39)), and

the projector will go into the FREEZE mode, which the picture
is frozen.
To exit the FREEZE mode and restore the screen to normal,
press the FREEZE button again.

● The projector automatically exits from the FREEZE mode when some control
buttons are pressed.

● If the projector continues projecting a still image for a long time, the LCD
panel might possibly be burned in. Do not leave the projector in the FREEZE
mode for too long.

FREEZE button

Temporarily blanking the screen

Press BLANK button on the remote control.

1.

The BLANK screen will be displayed instead of the screen of
input signal. Please refer to BLANK item in SCREEN menu
(37).
To exit from the BLANK screen and return to the input signal
screen, press BLANK button again.

● The projector automatically exits from the

BLANK

mode when

some control buttons are pressed.

BLANK button

•

NOTE

The sound is not connected with the BLANK screen function.

If necessary, set the volume or mute rst.

21

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

MENU

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

MENU

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE
UP

VOLUME

DOWN

࡯

ON

OFF

㧗

FREEZE

Using the menu function

This projector has the following menus:
PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, C.C.
and EASY MENU.
EASY MENU consists of functions often used, and the other menus are classied
into each purpose and brought together as the Advanced Menu.
Each of these menus is operated using the same methods. The basic operations
of these menus are as follows.

MENU button

INPUT button

ENTER button MENU button

Cursor buttons

Press the MENU button on the remote control or the projector.

1.

The Advanced Menu or EASY MENU, which has priority just after powered
on will appear.
If you want to move the menu position, use the cursor buttons after pressing
the POSITION button. While the projector is displaying any menu, the MENU
button on the projector works as the cursor buttons.

In the EASY MENU

If you want to change it to the Advanced Menu,

2.

select the Go to Advanced Menu...

Use the ▲/▼ cursor buttons to select an item to

3.

operate.

Use the ◄/► cursor buttons to operate the item.

4.

(continued on next page)

ESC button

RESET button

EASY MENU

22