Hitachi C21RF50S Service Manual

Download

Page 1

C21-RF50S

UA1 Chassis

PAL/SECAM/NTSC

SERVICE MANUAL

No.

C21-RF50S

A Color of Cabinet Destination Code

Silver MIDDLE EAST 191

Black

M’SIA & S’PORE 081

MIDDLE EAST

& AFRICA

191B

CAUTION: Before servicing this chassis, it is important that the service technician read the

"IMPORTANT SERVICE NOTES" in this Service Manual.

CONTENTS

Page

» SPECIFICATIONS .............................................. 2

» IMPORTANT SERVICE NOTES .........................2

» ADJUSTMENT PRECAUTIONS .........................3

» TROUBLE SHOOTING TABLE .........................18

» CHASSIS LAYOUT ........................................... 21

» BLOCK DIAGRAM ............................................22

» WAVEFORMS ...................................................25

» DESCRIPTION OF SCHEMATIC DIAGRAM .... 26

» SCHEMATIC DIAGRAMS

Ë CRT UNIT ...................................................... 27

Ë HEADPHONE UNIT ...................................... 27

Ë MAIN UNIT ................................................... 28

» PRINTED WIRING BOARD ASSEMBLIES ...... 30

» SOLID STATE DEVICE BASE DIAGRAM ........ 33

» REPLACEMENT PARTS LIST ......................... 34

Ë ELECTRICAL PARTS

MAIN UNIT ................................................... 34

CRT UNIT ...................................................... 39

HEADPHONE UNIT ......................................39

Ë SUPPLIED ACCESSORIES......................... 40

Ë PACKING PARTS ..........................................40

Ë CABINET PARTS .......................................... 41

Page

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

SEPTEMBER 2002 Digital Media System Group, Hitachi Asia Ltd.

01.C21-RF50S_E_p01-20 02.12.5, 12:461

COLOR TELEVISION

Page 2

C21-RF50S

2-2

IMPORTANT SERVICE NOTES

If there is a possibility that the high voltage fluctuates as a result of the

discharging the high voltage completely

Maintenance and repair of this receiver should be done by

qualified service personnel only.

SERVICING OF HIGH VOLTAGE SYSTEM AND

PICTURE TUBE

When servicing the high voltage system, remove static charge from it by

connecting a 10k ohm Resistor in series with an insulated wire (such as a

test probe) between picture tube dag and 2nd anode lead. (AC line cord

should be disconnected from AC outlet.)

1. Picture tube in this receiver employs integral implosion protection.

2. Replace with tube of the same type number for continued safety.

3. Do not lift picture tube by the neck.

4. Handle the picture tube only when wearing shatterproof goggles and after

X-RAY

This receiver is designed so that any X-Ray radiation is kept to an absolute

minimum. Since certain malfunctions or servicing may produce potentially

hazardous radiation with prolonged exposure at close range, the following

than 26.5 ± 1.5 kV (at beam 0.1 µA) for the set.

precautions should be observed:

2. To keep the set in a normal operation, be sure to make it function on 24.8 ±

1. When repairing the circuit, be sure not to increase the high voltage to more

NTSC-M

SECAM-B/G/DK/K1

repairs, never forget to check for such high voltage after the work.

1.5 kV (at beam 1,100 µA) in the case of the set. The set has been factory –

Adjusted to the above-mentioned high voltage.

C1 (49.75 MHz) thru C12 (216.25 MHz)

which may cause excess X-ray radiation.

3. Do not substitute a picture tube with unauthorized types and/or brands

S1 (105.25 MHz) thru S41 (463.25 MHz)

BEFORE RETURNING THE RECEIVER

C13 (471.75 MHz) thru C57 (863.25 MHz)

hardware is not lodged between the chassis and other metal parts in the

Before returning the receiver to the user, perform the following safety checks.

1. Inspect all lead dress to make certain that leads are not pinched or that

receiver.

fishpapers, cabinet backs, adjustment and compartment covers or shields, iso-

lation resistor-capacity networks, mechanical insulators and etc.

2. Inspect all protective devices such as non-metallic control knobs, insulating

Depth : 477.0 mm

Height : 475.0 mm

Weight (Approx) : 21.0 kg

2-1

SPECIFICATIONS

C21-RF50S/SB ....................................................................................................... 100 W

Power Input ................................................................................... AC 110 - 240V, 50/60 Hz

01.C21-RF50S_E_p01-20 02.12.5, 12:462

C21-RF50SN .......................................................................................................... 103 W

Power Consumption

Convergence .............................................................................. Self Convergence System

Focus .................................................................................... Quadra Potential Electrostatic

Sweep Deflection ................................................................................................... Magnetic

Picture IF Carrier ............................................................................................... 38.9 MHz

Sound IF Carrier Frequency

Intermediate Frequency

6.5 MHz .......................................................................................................... 32.4 MHz

6.0 MHz .......................................................................................................... 32.9 MHz

5.5 MHz .......................................................................................................... 33.4 MHz

Colour Sub-Carrier Frequency ....................................................................... 34.47 MHz

4.5MHz ............................................................................................................ 34.4 MHz

Audio Power Output Rating ....................................................................... 7.5 W × 2 (RMS)

Size ........................................................................................... 6 × 12 cm Elliptic (2 pcs.)

Voice Coil Impedance ........................................................................... 6 ohms at 400 Hz

Speaker

Aerial Input Impedance

VHF/UHF ....................................................................................... 75 ohm Unbalanced

Receiving System ........................................................................................... PAL-B/G/DK/I

Tuner Ranges

» VHF-Channels ........................................... E2 (48.25 MHz) thru E12 (224.25 MHz)

» UHF-Channels ...................................... E21 (471.25 MHz) thru E69 (855.25 MHz)

VHF ...................................................................................... 44.25 MHz thru 423.25 MHz

UHF ...................................................................................... 471.25MHz thru 863.25MHz

Receiving Frequency

Specifications are subject to change without prior notice.

Dimensions ............................................................................................... Width : 642.0 mm

Page 3

C21-RF50S

AGC &

GEOMETRIC

MODE

↓

AGC TAKE OVER POINT (AGC)

↓

VERTICAL SLOPE (V-LIN)

↓

VERTICAL AMP (V-AMP)

↓

VERTICAL SHIFT (V-CENT)

↓

HORIZONTAL SHIFT (H-CENT)

↓

EAST-WEST WIDTH (H-SIZE)

↓

HORIZONTAL PARALLELOGRAM (EW//)

↓

EAST-WEST PARABOLA/WIDTH (PARA)

↓

EAST-WEST UPPER CORNER PARABOLA (COR(U))

↓

EAST-WEST LOWER CORNER PARABOLA (COR(L))

↓

EAST-WEST TRAPEZIUM (TRAPE)

↓

HORIZONTAL BOW (HB)

↓

S-CORRECTION (S-COR)

WHITE POINT

ADJ.

MODE

↓

W.P. RED STD. W.T. (DRI-RS)

W.P. GREEN STD. W.T. (DRI-GS)

W.P.BLUE STD. W.T. (DRI-BS)

W.P. RED COOL W.T. (DRI-RC)

W.P. GREEN COOL W.T. (DRI-GC)

W.P. BLUE COOL W.T. (DRI-BC)

W.P. RED WARM W.T. (DRI-RW)

W.P. GREEN WARM W.T. (DRI-GW)

W.P. BLUE WARM W.T. (DRI-BW)

SUB

ADJ.

MODE

↓

MAX VOLUME (SUB-VOL)

↓

SUB CONTRAST (SUB-CON)

↓

SUB COLOUR (SUB-COL)

↓

SUB BRIGHTNESS (SUB-BRI)

↓

SUB TINT (SUB-TINT)

↓

SUB SHARPNESS (SUB-SHP)

↓

MAX HOTEL VOLUME (HTL-VOL)

↓

HOTEL PROGRAM NO(HTL-PRG)

↓

BLUE BACK CONTRAST (BB-CON)

↓

OSD RGB REFERENCE (RGB)

↓

BLACK LEVEL OFFSET R(CUT-R)

↓

BLACK LEVEL OFFSET G(CUT-G)

↓

CATHODE DRIVE LEVEL(CDL)

FORWARD : CH DOWN KEY

REVERSE : CH UP KEY

* ( ) means OSD display.

FORWARD : CH DOWN KEY

REVERSE : CH UP KEY

AGC &

GEOMETRIC

MODE

WHITE POINT

ADJ.

MODE

SUB

ADJ.

MODE

Y-DELAY

ADJ.

MODE

OPTION

MODE

STEREO

ADJ.

MODE

OFFSET

ADJ.

MODE

MISC.

OPTION

MODE

3-2

SERVICE MODE

(1) In the Service Mode, Key is used to select the mode in the following order.

C bus control and in the

C bus control include preset-only items

C bus

3-1

01.C21-RF50S_E_p01-20 02.12.5, 12:463

ADJUSTMENT PRECAUTIONS

and variable data.

This model’s setting are adjusted in two different ways: though the I

conventional analog manner. The adjustments via the I

mode position and the microprocessor is in input mode. (Adjustment through the I

control). (Use JWS Key to set as well).

one by one.

1 Make a short-circuit JA122 and JA124 for a second and release to switch to the service

2 Press the CH DOWN / UP key on the remote controller to get ready to select the mode

1. Setting the service mode by the microprocessor.

by one.

mode (OFF) position and the microprocessor is in out of the service mode.

3 Press the CH DOWN / UP key on the remote controller to select the modes reversibly one

4 Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.

5 Make a short-circuit JA122 and JA124 for a second and release to switch to the normal

2. Factory Presetting.

mode position and turn on the main power switch. Initial values are automatically preset,

only when a new EEPROM is used (Judge with the first 4 bytes).

1 Make a short-circuit JA122 and JA124 for a second and release to switch to the service

2 The initial data are preset as listed in pages 4-6.

FIRST TIME, make sure to make a short-circuit JA122 and JA124 switch to the serv-

ice mode position first and then turn on the main power switch. (See 2-1 above).

Precaution: If haven’t done this initiation, it may possibly generate excessive Beam

current.

3 Make sure the data need modify or not (Initial data).

Note: Once the chassis has been assembly together and ready to be POWER ON for the

3. For reference please check with memory map

(UA1 Series type RH-iX3410CE)

Page 4

C21-RF50S

↓

Y-D TIME FOR PAL (TV) (DL-PT)

↓

Y-D TIME FOR SECAM (TV) (DL-ST)

↓

Y-D TIME FOR N358 (TV) (DL-3T)

↓

Y-D TIME FOR N443 (TV) (DL-4T)

↓

Y-D TIME FOR B/W (TV) (DL-TV)

↓

Y-D TIME FOR PAL (AV) (DL-PA)

↓

Y-D TIME FOR SECAM (AV) (DL-SA)

↓

Y-D TIME FOR N358 (AV) (DL-3A)

↓

Y-D TIME FOR N443(AV) (DL-4A)

↓

Y-D TIME FOR B/W (AV) (DL-AV)

*(Y-D : Y-DELAY)

↓

COLOUR OFFSET (PAL) (COL-OP)

↓

COLOUR OFFSET (SECAM) (COL-OS)

↓

COLOUR OFFSET (NTSC358) (COL-O3)

↓

COLOUR OFFSET (NTSC443) (COL-O4)

↓

SHARPNESS OFFSET (PAL) (SHP-OP)

↓

SHARPNESS OFFSET (SECAM) (SHP-OS)

↓

SHARPNESS OFFSET (NTSC358) (SHP-O3)

↓

SHARPNESS OFFSET (NTSC443) (SHP-O4)

↓

VERTICAL SCAN DISABLE(VSD)

↓

BLACK STRETCH (BKS)

↓

AUTO VOLUME LEVELING(AVL)

↓

FAST FILTER IF-PLL(FFI)

↓

ENABLE VERTICAL GUARD (EVG)

↓

EHT TRACKING MODE (EHT)

↓

OVERSCAN SWITCH OFF(OSO)

↓

AUTO COLOUR LIMIT(ACL)

↓

FORCED COLOUR LIMIT(FCO)

Y-DELAY ADJ.

MODE

OFFSET ADJ.

MODE

IC OPTION

MODE

↓

SOUND SYSTEM M (S-M)

↓

SOUND SYSTEM DK (S-DK)

↓

SOUND SYSTEM I (S-I)

↓

SOUND SYSTEM BG (S-BG)

↓

PLAYBACK SECAM (P-SECAM)

↓

FE (RF) NTSC 3.58 (F-N358)

↓

FE (RF) NTSC 4.43 (F-N443)

↓

FE (RF) SECAM (F-SECAM)

↓

VIDEO MUTE AT IDENT LOSS (VMI)

↓

VIDEO MUTE AT PROGRAM

/SOURCE CHANGE (VMC)

↓

HOTEL MODE (HTL)

↓

REDUCED FM DEMODULATION

GAIN FOR BTSC SIGNAL (BTSC)

↓

NUMBER OF EXT AV SOURCE (AV)

↓

FM WINDOW SELECTION (FMWS)

↓

SOUND MUTE BIT 0 (SM0)

↓

SOUND MUTE BIT 1 (SM1)

↓

THAI LANGUAGE (THA)

↓

ARABIC LANGUAGE (ARA)

↓

MALAY LANGUAGE (MAL)

↓

CHINESE LANGUAGE (CHI)

↓

MISC. OPTION

MODE

↓

BASS MIX FOR ANXXXX (BM_ON)

↓

BASS MIX AFFECT FOR ANXXXX (BM_EFF)

↓

AGC FOR ANXXXX (AGC_ON)

↓

AGC ADJUS FOR ANXXXX (AGC_ADJ)

↓

NICAM AGC (AGC_N)

↓

NICAM AGC GAIN ADJ (GAIN_N)

↓

FM OUTPUT LEVEL (FM_LV)

↓

IGR OUTPUT LEVEL (IGR_LV)

↓

NICAM OUTPUT LEVEL B/G (BG_NLV)

↓

NICAM OUTPUT LEVEL I (I_NLV)

↓

NICAM OUPUT LEVEL D/K (DK_NLV)

↓

NICAM LOWER ERR LIMIT (LOW-ERR)

↓

NICAM UPPER ERR LIMIT (UP_ERR)

↓

IGR STR R CH GAIN ADJ (IGR_STR)

SOUND PROCESSOR AND

STEREO ADJ MODE

↓

FRENCH LANGUAGE (FRE)

↓

RUSSIAN LANGUAGE (RUS)

↓

FORCED V-SYNC SLICING LEVEL(FSL)

↓

SYNC OF OSD (HP2)

↓

IF AGC SPEED BIT 0 (AGC0)

↓

IF AGC SPEED BIT 1 (AGC1)

↓

FOA Time Constant-RF (FOA-FE)

↓

FOB Time Constant-RF (FOB-FE)

↓

FOA Time Constant-AV (FOA-AV)

↓

FOB Time Constant-AV (FOB-AV)

↓

TELETEXT (TXT)

↓

TEXT WEST OR EURO CHAR (TXT_W/E)

↓

TEXT PAN-EURO LANG (TXT-EUR)

↓

IF FREQ SELECTION (IF_38_0)

↓

CHARGE PUMP (CP)

↓

AN5890 ON (AN5890)

↓

AN5891 ON (AN5891)

↓

AN7396 ON (AN7396)

↓

NICAM DECODING (NICAM)

↓

IGR DECODING (IGR)

↓

GAME MODE (GAME)

↓

BILINGUAL (BIL)

LED Blink Speed When ON-Timer is active (LED-F)

PWM Volume Table for Mono (MSA)

Output Vertical Guard (NDF)

OSD "IGR" or "A2" Display (A2)

USER DATA IN SERVICE MODE

MODE USER DATA

CONTRAST MAX

COLOUR CENTER

BRIGHTNESS CENTER

TINT CENTER

SHARPNESS CENTER

same as before switch

to Service mode.

*1 : For each CH, data is

WHITE TEMP STANDARD

S-VOLUME MAX

BLUE BACK OFF

C SYSTEM AUTO

S SYSTEM *1

RC COMMAND SERVICE-ITEM

STANDBY/ON STANDBY

TV/VIDEO NEXT SOURCE

4-2

DIGIT 0ˇ9 DIGIT 0ˇ.9

AV1 SELECT AV1

AV2 SELECT AV2

-/-- 1/2 DIGIT ENTRY

FUNCTION FSET AGC

TIMER TSET SUB-VOL

TXT/MIX DRI-GS

PIC DRI-BS

HOLD DRI-GC

CANCEL DRI-GW

SIZE DRI-RC

REVEAL DRI-BW

RED CUT-R

GREEN CUT-G

BLUE BACK S-COR

S-SYSTEM HB

CONTRAST+ SUB-CON

CONTRAST- V-LIN

COLOUR+ SUB-COL

COLOUR- V-AMP

BRIGHTNESS+ SUB-BRI

BRIGHTNESS- V-CENT

TINT+ SUB-TINT

TINT- H-CENT

SHARPNESS+ SUB-SHP

SHARPNESS- EW//

BASS+ FM LV

BASS- IGR LV

TREBLE+ IGR STR

TREBLE- B/G NLV

Also, once SERVICE mode OFF, EEPROM will switch back to previous USER DATA.

* While SERVICE mode ON, EEPROM DATA will switch to the service data.

* In the service mode, the user data establish as below,

* Direct Key-in for service item in service mode

4-1

01.C21-RF50S_E_p01-20 02.12.5, 12:464

Page 5

REMARK

0 FIX

INITIAL DATA FIX/ADJ

0(DISABLE)/1(ENABLE)

1 FIX

0 FIX

0(DISABLE)/1(ENABLE)

0(ENABLE)/1(DISABLE)

0 FIX

1 FIX

0 FIX

1 FIX

0 FIX

0(DISABLE)/1(ENABLE)

1 FIX

0(1) FIX

0(DISABLE)/1(ENABLE)

1 FIX

0(1) FIX

0(DISABLE)/1(ENABLE)

1 FIX

0 FIX

1 FIX

0 FIX

0(DISABLE)/1(ENABLE)

VMC

BTSC

1 FIX

0 FIX

1 FIX

0 FIX

0(DISABLE)/1(ENABLE)

C21-RF50S

0 FIX

1 FIX

0 FIX

5-2

0(DISABLE)/1(ENABLE)

0(WESTERN)/1(EASTERN)

0(DISABLE)/1(ENABLE)

EEPROM ITEMS OSD DATA LENGTH

SHARPNESS OFFSET (NTSC358) SHP-O3 0~15 12 FIX

SHARPNESS OFFSET (NTSC443) SHP-O4 0~15 8 FIX

BASS MIX FOR ANXXXX BM-ON

BASS MIX EFFECT FOR ANXXXX BM-EFF 0~3 2 FIX

AGC FOR ANXXXX AGC-ON

AGC ADJUST FOR ANXXXX AGC-ADJ 0~3 3 FIX

REMARK

INITIAL DATA FIX/ADJ

NICAM AGC AGC-N

NICAM AGC GAIN ADJ GAIN-N 0~31 0 FIX

FM OUTPUT LEVEL FM-LV 0~30 15(22) FIX

IGR OUTPUT LEVEL IGR-LV 0~30 16(23) FIX

NICAM OUTPUT LEVEL (B/G) B/G-NLV 0~30 13(20) FIX

NICAM OUTPUT LEVEL (I) I-NLV 0~30 18(25) FIX

NICAM OUTPUT LEVEL (D/K) D/K-NLV 0~30 13(20) FIX

NICAM LOWER ERROR LIMIT LOW ERR 0~255 35(20) FIX

NICAM UPPER ERROR LIMIT UP ERR 0~255 70 FIX

IGR STEREO R CH GAIN ADJUST IGR-STR 0~13 6 FIX

VERTICAL SCAN DISABLE VSD

BLACK STRETCH BKS

AUTOMATIC VOLUME LEVELING AVL

FAST FILTER IF-PLL FFI

ENABLE VERTICAL GUARD (RGB BLANKING) EVG

EHT TRACKING MODE (HCO) EHT

OVERSCAN SWITCH OFF OSO

AUTO COLOUR LIMIT ACL

FORCED COLOUR LIMIT FCO

SOUND SYSTEM M S-M

SOUND SYSTEM DK S-DK

SOUND SYSTEM I S-I

SOUND SYSTEM BG S-BG

PLAYBACK SECAM P-SECAM

FE (RF) NTSC 3.58 F-N358

FE (RF) NTSC 4.43 F-N443

FE (RF) SECAM F-SECAM

VIDEO MUTE AT IDENT LOSS VMI

VIDEO MUTE AT PROGRAM/SOURCE CHANGE

HOTEL MODE HTL

REDUCED FM DEMODULATOR GAIN FOR BTSC SIGNAL

NUMBER OF EXTERNAL AV SOURCE AV 0 FOR1 AV/1 FOR 2AV 1 FIX

FM WINDOW SELECTION FMWS

SOUND MUTE BIT 0 SM0

SOUND MUTE BIT 1 SM1

THAI LANGUAGE THA

ARABIC LANGUAGE ARA

MALAY LANGUAGE MAL

CHINESE LANGUAGE CHI

FRENCH LANGUAGE FRE

RUSSIAN LANGUAGE RUS

FORCED V-SYNC SLICING LEVEL FSL

SYNC OF OSD HP2

IF AGC SPEED BIT 0 AGC0

IF AGC SPEED BIT 1 AGC1

PHI-1 TIME CONSTANT (RF) FOA-FE

PHI-1 TIME CONSTANT (RF) FOB-FE

PHI-1 TIME CONSTANT (OFF AIR) FOA-AV

PHI-1 TIME CONSTANT (OFF AIR) FOB-AV

TELETEXT TXT

TELETEXT WESTERN OR EASTERN CHAR TXT-W/E

(DRI-BS) SAME DATA

32 FIX

255 FIX

0~99 OR>99FOR NONE

5-1

EEPROM ITEMS OSD DATA LENGTH

00H: 55H 02H: 53H

01H: 41H 03H: 36H

Address Data Address Data

After short JA122 & JA 124, and turn on the main power switch, read data from EEPROM

address 00H ~ 03H, and compare to the list below, if different, initialize the EEPROM.

01.C21-RF50S_E_p01-20 02.12.5, 12:465

AGC TAKE OVER POINT AGC 0~63 14 ADJ

VERTICAL SLOPE V-LIN 0~63 32 ADJ

VERTICAL AMPLITUDE V-AMP 0~63 32 ADJ

VERTICAL SHIFT V-CENT 0~63 32 ADJ

HORIZONTAL SHIFT H-CENT 0~63 32 ADJ

EAST-WEST WIDTH [EW] H-SIZE 0~63 32 FIX

HORIZONTAL PARALLELOGRAM EW// 0~63 32 FIX

EAST-WEST PARABOLA/WIDTH PARA 0~63 32 FIX

EAST-WEST UPPER CORNER PARABOLA COR(U) 0~63 32 FIX

EAST-WEST LOWER CORNER PARABOLA COR(L) 0~63 32 FIX

EAST-WEST TRAPEZIUM [TC] TRAPE 0~63 32 FIX

HORIZONTAL BOW HB 0~63 32 FIX

S-CORRECTION S-COR 0~63 0 (20) FIX

WHITE POINT RED STD WHITE TEMP DRI-RS 0~63 32 FIX

WHITE POINT GREEN STD WHITE TEMP DRI-GS 0~63 32 ADJ

WHITE POINT BLUE STD WHITE TEMP DRI-BS 0~63 32 ADJ

WHITE POINT RED COOL WHITE TEMP DRI-RC 0~63 25 FIX (DRI-BS)-7 DATA

WHITE POINT GREEN COOL WHITE TEMP DRI-GC 0~63 32 FIX (DRI-GS)-7 DATA

WHITE POINT BLUE COOL WHITE TEMP DRI-BC 0~63

WHITE POINT RED WARM WHITE TEMP DRI-RW 0~63 32 FIX

WHITE POINT GREEN WARM WHITE TEMP DRI-GW 0~63 32 FIX (DRI-GS)-7 DATA

WHITE POINT BLUE WARM WHITE TEMP DRI-BW 0~63 32 FIX (DRI-BS)-7 DATA

MAX VOLUME SUB-VOL 0~60 60 FIX

SUB CONTRAST SUB-CON 0~63 63 FIX

SUB COLOUR SUB-COL 0~63 32 ADJ

SUB BRIGHTNESS SUB-BRI 0~63 32 ADJ

SUB TINT SUB-TINT 0~63 32 ADJ

SUB SHARPNESS SUB-SHP 0~63 32(20) ADJ

MAX HOTEL VOLUME HTL-VOL 0~60 30 ADJ

HOTEL PROGRAM NUMBER HTL-PRG

BLUE BACK CONTRAST BB-CON 0~15 10 FIX

OSD GRB REFERENCE RGB 0~15 15 FIX

BLACK LEVEL OFF-SET R CUT-R 0~63 32 FIX

BLACK LEVEL OFF-SET G CUT-G 0~63 32 FIX

CATHODE DRIVE LEVEL CDL 0~15 0 (7) FIX

Y-DELAY TIME FOR PAL(TV) [YD] DL-PT 0~15 12 FIX

Y-DELAY TIME FOR SECAM(TV) [YD] DL-ST 0~15 15 FIX

Y-DELAY TIME FOR N358 (TV) [YD] DL-3T 0~15 12 FIX

Y-DELAY TIME FOR N443 (TV) [YD] DL-4T 0~15 12 FIX

Y-DELAY TIME FOR B/W (TV) [YD] DL-TV 0~15 12 FIX

Y-DELAY TIME FOR PAL (AV) [YD] DL-PA 0~15 12(9) FIX

Y-DELAY TIME FOR SECAM (AV) [YD] DL-SA 0~15 15 FIX

Y-DELAY TIME FOR N358 (AV) [YD] DL-3A 0~15 12(7) FIX

Y-DELAY TIME FOR N443 (AV) [YD] DL-4A 0~15 12 FIX

Y-DELAY TIME FOR B/W (AV) [YD] DL-AV 0~15 12 FIX

COLOUR OFFSET (PAL) COL-OP 0~15 8 FIX *1

COLOUR OFFSET (SECAM) COL-OS 0~15 8 FIX *1

COLOUR OFFSET (NTSC358) COL-O3 0~15 4 FIX *1

COLOUR OFFSET (NTSC443) COL-O4 0~15 4 FIX *1

SHARPNESS OFFSET (PAL) SHP-OP 0~15 8 FIX

SHARPNESS OFFSET (SECAM) SHP-OS 0~15 4 FIX

Page 6

C21-RF50S

MCL1

INITIAL SETTING

1 48.25 B/G

2 62.25 B/G

3 77.25 D/K

0 FIX

0(1) FIX

4 175.25 B/G

0 FIX

INITIAL3 : for Singapore, Malaysia, Middle East and Africa.

(1) Please set to MCL1.

(2) After set the MCL please set the INITIAL SETTING as below.

REMARK

0 FIX

1(0) FIX

0(1) FIX

INITIAL DATA FIX/ADJ

CH-NO Fv (MHz) SOUND SYS

0 FIX

0(1) FIX

5 182.25 B/G

0 FIX

6 183.25 D/K

7 191.25 D/K

8 196.25 B/G

6-2

9 199.25 M

10 210.25 B/G

11 224.25 B/G

12 471.25 B/G

13 487.25 I

14 503.25 B/G

15 575.25 B/G

16 583.25 B/G

17 599.25 B/G

18 621.25 M

19 639.25 D/K

20 703.25 B/G

21 735.25 I

22 767.25 B/G

23 815.25 B/G

24 855.25 I

25 855.25 B/G

26 55.25 M

27 83.25 M

28 183.25 M

29 193.25 M

30 217.25 M

31 471.25 M

32 477.25 M

33 693.25 M

34 41.1 M

35 112.25 B/G

36 168.25 B/G

38 294.25 B/G

39 463.25 B/G

41 647.25 B/G

42 663.25 B/G

43 679.25 B/G

44 174.95 B/G

45 175.55 B/G

0(DISABLE)/1(ENABLE)

0(FAST TUNE)/1(MODERATE TUNE)

EEPROM ITEMS OSD DATA LENGTH

TELETEXT PAN-EURO LANG TXT-EUR 0(EURO)/1(OTHER) 0 FIX

AN5890 PRESENT AN5890

AN5891 PRESENT AN5891

AN7396 PRESENT AN7396

NICAM DECODING ENABLED NICAM

IGR DECODING ENABLED IGR

GAME MODE ENABLED GAME

IF FREQ SELECTION IF_38_0 0(38.9)/1(38.0) 0 FIX

BILINGUAL BIL

CHARGE PUMP CP

LED BLINK SPEED LED_F 0(100Hz) OR 1(1Hz) 0 FIX

01.C21-RF50S_E_p01-20 02.12.5, 12:466

0(DISABLE)/1(ENABLE)

0(IGNORE) OR 1 (ACCEPT)

0(ORIGINAL-TABLE A) OR 1 TABLE B

MSA

Please set the EEPROM initial data according to the value in parenthesis ( ) before adjustment

Fixed data, please do not change without specific instruction.

VOLUME CONTROL PWM CONVERSION TABLE

OSD A2 IN STEREO A2

OUTPUT VERTICAL GUARD NDF

NOTE :

*1:After Adj. SUB-COLOUR then change, 1. COL-OP FROM 8 TO 14

2. COL-OS FROM 8 TO 14

3. COL-O3 FROM 4 TO 10

4. COL-O4 FROM 4 TO 10

6-1

Page 7

C21-RF50S

E-9 CH

P C

10k

100k

1N60

75ohm

IF OUT

-1.5+/-0.8dB

1000p

Oscilloscope

» Bias box: About 4.5 V

Oscilloscope

0.1V

TV Set

Bias box

TP201+

–

Fig. 1

PIF ADJUSTMENT

nal, but with no signal input.

Adjust the PLL data.

2. Connect the sweep generator's output cable

1. Get the tuner ready to receive the E-9 CH sig-

Tuner IFT

(PRESET)

NO. Adjustment part Adjusting procedure and conditions Waveform and others

ANCE probe with wave detector; see Fig.1) to

the tuner's IF output terminal. (This terminal

to the tuner antenna. (RF SWEEP)

3. Adjust the sweep generator's to 80dBµV.

must have the probe alone connected).

4. Connect the response lead (use LOW IMPED-

5. Set the RF AGC to 0 - 6 V with no saturation

Fig. 2

For the 50 ohm signal strength

gauge, when not using 50/75

impedance adapter, signal

strength is 52 ±1 dBµV(75 ohm

open), instead of 54 ±1 dBµV

(75 ohm open).

The loss of using impedance

Note:

adapter

Precaution:

7-2

Fig. 3

with the waveform.

6. Adjust the tuner IF coil to obtain the waveform

tion during this adjustment.

as shown in Fig. 2.

Note: Be sure to keep the tuner cover in posi-

AGC Terminal) as shown in Fig. 3.

» Signal Strength: 54 ±1 dBµV (75 ohm open)

1. Receive the PAL colour bar signal.

2. Connect the oscilloscope to TP201 (Tuner’s

C BUS

TAKE OVER

POINT

ADJUSTMENT

CONTROL)

RF-AGC

the "AG" bus data to obtain the Tuner output

pin drop 0.1 V below maximum voltage.

63~67dBµV, and make sure there is no noise.

3. Call the "AG" mode in service mode. Adjust

sure that there is no cross modulation beat.

4. Change the antenna input signal to

5. Turn up the input signal to 90~95 dBµV to be

PROM.

SHIPPING SETTING & CHECKING

ITEMS DATA SETTING

LAST PROGRAM/CHANNEL 1

(1) The following default data has been factory-set for the E

01.C21-RF50S_E_p01-20 02.12.5, 12:467

FLASHBACK PROGARM/CH 1

DIGIT 2 DIGIT

C-SYSTEM AUTO

CHANNEL WILL BE SKIPPED

NOTE: AFTER PRESSING MODEL SETTING, 0

7-1

(Reference: Geomagnetism Adjustment)

30,000 20,000 12300K ARABIC B/G 6

-10,000 40,000 12300K ENGLISH B/G 6

FACTORY SETTING BY MODEL

MODEL MAGNEYIC FIELD (V, H) nT BACKGROUND LANG. S-SYS LANG QTY

S-SYSTEM *1

SKIP OFF

AFC ON

VOLUME 1

CONTRAST 60 (MAX)

COLOUR 0 (CENTER)

BRIGHTNESS 0 (CENTER)

TINT 0 (CENTER)

SHARPNESS 0 (CENTER)

WHITE TEMP STANDARD

REMINDER TIMER In-active, "--:--"

ON TIMER In-active, "--:--"

OFF TIMER In-active, "--:--"

LAST POWER POWER-ON

LANGUAGE *1

BLUE BACK MUTE ON

HOTEL MODE OFF

0 CHANNEL SKIP ON

LAST TV/AV TV

BASS/TRE/BAL CENT

SURROUND OFF

SURROUND LEVEL CENT

*1:Please refer defaults for LANGUAGE and SOUND SYSTEM per MODEL as follows.

(191)

C21-RF50S

(081,191B)

C21-RF50S

*NOTE FOR OSD TYPE

ENGLISH/CHINESE/FRENCH/ARABIC/MALAY/RUSSIAN

Page 8

C21-RF50S

A = B

Rank "A"

(on the right of the CRT)

Rank "A"

(on the left of the CRT)

Red-only

Green-only

Blue-only

Signal-colour

screen cleared

RGB

BGR

RGB

BGR

Lacquer

Wedge "a"

Wedge

"b"

Wedge

"c"

About

100°

About

100°

4-pole magnet

6-pole magnet

CRT neck

Lacquer

Purity magnet

Fig. 5-1

1. Receive the Crosshatch Pattern signal.

2. Using the remote controller, call NORMAL

CONVER-

GENCE ADJ.

NO. Adjustment part Adjusting procedure and conditions Waveform and others

mode.

(To be done

CONVERGENCE ADJUSTMENT

angle in order to superpose the blue and red

colours.

angle in order to superpose the green colour

Static Convergence

1. Turn the 4-pole magnet to a proper opening

after the purity

adjustment.)

over the blue and red colours.

2. Turn the 6-pole magnet to a proper opening

Fig. 5-2

screen in the following steps.

Dynamic Convergence

1. Adjust the convergence on the fringes of the

swing the deflection coil upward.

and "c" and swing the deflection coil

b) Fig. 5-2: Drive the wedge at points "b"

a) Fig. 5-1: Drive the wedge at point "a" and

Fig. 5-3

swing the deflection coil rightward.

downward.

c) Fig. 5-3: Drive the "c" wedge deeper and

d) Fig. 5-4: Drive the "b" wedge deeper and

swing the deflection coil leftward.

magnet unit (purity, 4-pole, 6-pole magnets)

tape over them.

2. Fix all the wedges on the CRT and apply glass

3. Apply lacquer to the deflection yoke lock screw,

Fig. 5-4

and magnet unit lock screw.

Finally received the Red-only and Blue-only

signals to make sure there is no other colours

on the screen.

Fig. 5-5

Fig. 5-6

8-2

Fig. 4-1

PURITY ADJUSTMENT

4-1 through the microscope. Adjust the land-

beam current to about 700 µA.

1. Receive the GREEN-ONLY signal. Adjust the

PURITY ADJ.

NO. Adjustment part Adjusting procedure and conditions Waveform and others

netic field and keep the static convergence

coil.

2. Degauss the CRT enough with the degausing

3. Maintain the purity magnet at the zero mag-

ing to the rank A requirement.

roughly adjusted.

4. Observe the points a and b as shown in Fig.

5. Orient the raster rotation to 0 eastward.

6. Tighten up the deflection coil screws.

» Tightening torque: 108N ± 20 N (11 ± 2 kgf)

warming up the unit for 30 minutes

or longer with a beam current over

700µA.

A rank requirements. If not, stick the magnet

sheet to correct it.

Note:This adjustment must be done after

7. Make sure the CRT corners landing meet the

Note:Set the service mode by TP1001 &

Fig. 4-2

TP1002 (short) then press factory

process R/C RGB key to change to

Fig. 4-3

in NORMAL MODE, the colour

will change to RGB mono colour

mode.

The TEXT Key "R. G. Cy" Key can

be directly use to change to other

* Press R/C RGB key for 1 second

colours screen.

8-1

RGB mono colour mode.

change.

* For the following colours press R/C RGB key to

01.C21-RF50S_E_p01-20 02.12.5, 12:468

Page 9

Y 100%W

75%

Mg R

1 2 3 4 5

3.2Vdc

1 2 3 4 5

the horizontal line in the center of monoscope is

1. Receive the monoscope pattern signal.

just at the position where the blanking starts.

2. Call the "V-LIN" mode.

3. Increase or decrease "V-LIN" by Volume key till

till the picture is centered.

1. Call the "V-CENT" mode.

2. Increase or decrease "V-CENT" by Volume key

to set overscan of 9.5% typical.

Adjustment Spec. 9.5% range +1% -0%.

1. Call the "V-AMP" mode.

2. Increase or decrease "V- AMP" by Volume key

FIXED DATA, NO NEED TO ADJUST.

C21-RF50S

Fig. 8

9-2

OS=8, COL-O3=4, COL-O4=4

After adjust SUB COL, set COL-OP=12, COL-

to center the picture horizontal.

1. Call the "H-CENT" mode.

2. Increase or decrease "H-CENT" by Volume key

1. Receive the monoscope pattern signal.

2. Press R/C to set Picture NORMAL condition.

3. Adjust the focus control to get the best focus.

PAL CHROMA ADJUSTMENT

(C881 and R885).

» Range : 20 V/div. (AC) (Use 10:1 probe)

» Sweep time : 10 µsec/div.

mode. Adjust SUB COLOUR bus data, so that

the 75% White & Red portions of PAL Colour

1. Receive the PAL colour bar signal.

2. Press R/C to set Picture Normal condition.

3. Connect the oscilloscope to Red cathode

4. Using the R/C call "SUB COL" in SERVICE

Bar be at the same level shown as Fig. 8.

5. Clear the SERVICE mode.

OS=12, COL-O3=8, COL-O4=8

* Before adjust SUB COL, COL-OP=8, COL-

C BUS

V-SLOPE

CONTROL)

HORIZONTAL, VERTICAL, DEFLECTION LOOP AND FOCUS ADJUSTMENT

NO. Adjustment part Adjusting procedure and conditions Waveform and others

as beside procedure.

line appear and make sure the colour

* Alternative Procedure:

(1) Step (1), (2), (3) and (4) are same

(2) Then continue adjust until retrace

C BUS

V-SHIFT-50

appear wheather red, green or blue.

test points as belowwhich is based

on colour appear at (2)

(3) Connect the oscilloscope to related

C BUS

CONTROL)

V - AMP 50

CONTROL)

RED=TP851, GREEN=TP852,

BLUE=TP853

of signal reach 3.2Vdc

(4) Then adjust Screen VR until the tip

S-CORREC-

TION (I

BUS CON-

TROL)

C BUS

H-SHIFT (50)

(H-CENTER)

CONTROL)

Line 3 is one step (data) brighter than line 2

Focus

Y : 0.275

# 12300°K X : 0.272

(MINOLTA COLOUR ANALYZER CA-

100)

*Note: Above Data can be UP/DOWN

by Volume key.

**BRIGHTNESS

C BUS

SUB COLOUR

NO. Adjustment part Adjusting procedure and conditions Waveform and others

120cd/m

LOW HIGH

10cd/m

CONTROL)

9-1

NO VIDEO signal.

1. Switch TV to VIDEO mode,BLUE BACK OFF, with

2. Press R/C to set Picture Normal condition.

tor.

3. Frist off the screen by adjust screen variable resis-

screen variable resistor until colour raster suddenly

On and Off (AKB start function).

*4. Next, check AKB circuit function by slowly increase

5. Then continue adjust until retrace line appear.

until screen retrace line(Not Raster) Cut Off.

6. Finally, slowly decrease the screen variable resistor

*Note :

Must comfirm the AKB function in set before con-

tinue the next adjustment.

REMARK :

RS/RC/RW, DRI-GS/GC/GW, DRI-BS/BC/BW, CUT-

R AND CUT-G must be initial data.

2) CRT Cutoff adjustment must be done inside a dark

1) Before CRT Cutoff adjustment, SUB-BRIGHT, DRI-

room.

hatch pattern with 5 black level windows)

line 1 and 2 have the same darkness wherelse line

1. Call " SUB-BRI" in service mode. (Receive Cross-

3 is one step (data) brighter than line 2. Finally data

2. Adjust the " SUB BRIGHT " bus data in order that the

minus 1 to make line 1, 2, and 3 are in same level

(darkness).

3. Clear the SERVICE mode.

1. Receive the "WHITE" pattern with BURST signal.

(MINOLTA CA-100)

( - ) TP 603 ( + ).

2. Press R/C to set Picture NORMAL condition.

120cd/m

3. Connect the DC miliammeter between the TP 602

4. Check Beam current should be around 1100µA.

5. Set BRIGHTNESS Y by generator, to high brightness

(MINOLTA CA-100)

DRI-BS data to have a colour temperature of

12,300°k. *Note.

10cd/m

6. Switch TV to service mode and adjust the DRI-GS &

7. Set BRIGHTNESS Y by generator, to low brightness

8. Adjust "CUT-R" & "CUT-G" to get desired colour tem-

ing up the unit for 30 minutes or longer

with a beam current over 700µA.

Note : This adjustment must be done after warm-

perature #. Then go back NORMAL mode (HIGH

BRIGHT**) to check colour temperature. If out of

range, back to (1)

* ADJUST DRI-GC/GW, DRI-BC/BW as following DATA,

TP602 (–).

DRI-RW=32 (FIXED), DRI-GW="DRI-GS"-7*, DRI-

BW="DRI-BS"-7*

DRI-RS=25(FIXED), DRI-BC="DRI-BS", DRI-

after finishing DRI-BS and DRI-GS

GC="DRI-GS"-7

9. Clear the SERVICE mode.

(Full Scale: 3 mA Range)

1. Receive the "Monoscope Pattern" signal.

2. Press R/C to set Picture NORMAL condition.

3. Connect the DC miliammeter between TP603 (+) &

4. Beam current must be within 1,100 ± 100 µA.

CUT-OFF, BKGD, SUB-CONT (1) ADJUSTMENT

CRT CUTOFF

ADJUSTMENT

NO. Adjustment part Adjusting procedure and conditions Waveform or others

C BUS (I

CONTROL)

C BUS

SUB-

BRIGHTNESS

ADJUSMENT

((I

CONTROL)

WHITE

BALANCE

SERVICE

C BUS

MODE ADJ

CONTROL)

Maximum

beam check

01.C21-RF50S_E_p01-20 02.12.5, 12:469

Page 10

C21-RF50S

Same level

Cy G Mg R

1. Receive the monoscope pattern signal.

2. Set P-Mode to select CONTRAST.

the CONTRAST effect is OK or not.

3. Press Volume Up/Down key to check whether

1. Receive the colour bar signal.

1. Receive the monoscope pattern signal.

2. Set P-Mode to select BRIGHTNESS.

3. Press Volume Up/Down key to check whether

the BRIGHTNESS effect is OK or not

1. Receive the NTSC colour bar signal thru AV

the COLOUR effect is OK or not.

2. Set P-Mode to select COLOUR.

3. Press Volume Up/Down key to check whether

in.

for GREEN direction and DOWN for PURPLE

direction whether is OK or not.

2. Set P-Mode to select TINT.

3. Press Volume Up/Down key to check TINT, UP

1. Receive the monoscope pattern signal.

2. Set P-mode to select SHARPNESS.

the SHARPNESS effect is OK or not.

3. Press Volume Up/Down key to check whether

contrast, colour, bright, tint

or sharpness are all in nor-

mal setting.

Note:If nothing is display mean

TREBLE : CENTER

BASS : CENTER

channel number in green colour under AFT ON

condition.

1. All Ch (1~99) will have an OSD display of the

key is pressed, all the settings will be present

to normal setting.

(Normal setting value for every mode).

» CONTRAST : MAX

1. Once in PICTURE Mode, and the NORMAL

» COLOUR : CENTER

: CENTER

SURROUND : OFF

SURROUND LEVEL

BALANCE : CENTER

: CENTER

BRIGHTNESS

SHARPNESS

» TINT : CENTER

1. Receive the monoscope pattern signal.

2. Set P-mode to select WHITE TEMP.

TEMP Option, STANDARD:

NORMAL SETTING, WARM for more RED-

3. Press Volume Up/Down key to check WHITE

10-2

DISH direction changing, COOL for more BLU-

ISH direction changing.

CONTRAST

FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)

NO. Adjustment part Adjusting procedure and conditions Waveform and others

key

2 COLOUR key

BRIGHTNESS

key

Fig. 9

SHARPNESS

Key

4 TINT key

each short test.

* Select one of Q883/5/7 to do

CH DISPLAY

COLOUR

7 NORMAL Key

8 White Temp

10-1

Colour Bar, Sound 400 Hz 100% Mod.)

pedance. Make sure the output is as specified

through AV in.

P882) BLUE-OUT.

» Range : 100mV/div. (AC)(Use Probe 10:1)

» Sweep time: 10 µsec/div.

Adjust the "SUB-TINT" bus data to obtain the

NTSC CHROMA ADJUSTMENT

1. Receive the NTSC3.58 colour bar signal

2. Connect the oscilloscope to TP853 (Pin (5) of

C BUS

SUB-TINT

CONTROL)

NO. Adjustment part Adjusting procedure and conditions Waveform and others

waveform shown as Fig. 9.

3. Call the "SUB-TINT" mode in service mode.

4. Clear the SERVICE mode.

short, make sure the protector ON and switch

1. Receive the monoscope pattern signal.

2. Set CONTRAST MAX.

to standby mode.

3. Set BRIGHT MAX.

4. During the Collector & Emitter of Q883/5/7

1. Receive the monoscope pattern signal.

PROTECTOR OPERATION CHECKING

BEAM

PROTECTOR

NO. Adjustment part Adjusting procedure and conditions Waveform and others

H·V PROTEC-

(R606 side).

the protector is not work.

3. Set voltage of Bias Box to 18V and make sure

the protector is work.

4. Set voltage of Bias Box to 27V, and make sure

2. Connect output of Bias Box to D607 cathode

TOR

testing in +B line, check all possible damaged

components on +B line.

1. Once finish rectified Electrolytic Capacitor shor t

Other

protectors

(Use random selected set for inspection)

1. Receive the PAL colour bar signal (100% White

A/V INPUT AND OUTPUT CHECKING

VIDEO AND

NO. Adjustment part Adjusting procedure and conditions Waveform and others

(1.0 Vp-p ±3 dB).

2. Terminate the Video output with a 75 ohm im-

AUDIO OUT-

PUT CHECK

pedance. Make sure the output is as specified

3. Terminate the Audio output with a 10k ohm im-

make sure that the modes change in order of

(1.76 Vp-p ±3 dB).

1. Using the TV/AV key on the remote controller,

VIDEO AND

AUDIO INPUT

TV, AV1, AV2 & TV again and the video & au-

dio output are according to the input terminal

for each mode.

CHECK

01.C21-RF50S_E_p01-20 02.12.5, 12:4610

Page 11

(Continued)

QUANTITY ENGLISH RUSSIAN CHINESE ERENCH ARABIC MALAY

Check OSD LANGUAGE quantity and type for

respect model.

6OOOOOO

SURROUND OFF

↓

to check the sound effect.”

"BAL".

1. Receive the monoscope pattern signal.

2. Set P-Mode to select the "BASS", "TRE" and

3. Select each item, and press Vol. Up/Down Key

mode.

1. Receive the music signal.

2. Press SURROUND Key to select the following

(Check SURROUND sound effect)

SURROUND 1

Check the level of SURROUND 1 effect by in-

(Check MONO sound effect)

SURROUND 2

creasing and decreasing the level control.

ROUND Key to select the following mode.

3. Receive the music signal and press SUR-

400Hz, 100% Modulation (±50 kHz Dev).

output with 400Hz sound and no sound out

HEADPHONE JACK CHECKING

1. Receive the PAL colour bar with SOUND

from speaker.

2. Maximum volume, and check the headphone

C21-RF50S

11-2

FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)

NO. Adjustment part Adjusting procedure and conditions Waveform and others

(Continued)

OSD

LANGUAGE

QUANTITY

CHECK

SOUND

CONTROL

(BASS/TRE/

BAL)

SURROUND

FUNCTION

CHECKING

HEADPHONE

OUTPUT

NO. Adjustment part Adjusting procedure and conditions Waveform and others

CHECKING

11-1

COLOUR SYSTEM key to select modes ex-

cept PAL, check the COLOUR is not working

1. Receive the PAL colour bar signal, select the

Colour

system

FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)

01.C21-RF50S_E_p01-20 02.12.5, 12:4611

NO. Adjustment part Adjusting procedure and conditions Waveform and others

properly. Then, select the "PAL" mode. Check

again its colour so that it is working properly.

the COLOUR SYSTEM key to select modes

except SECAM, check the COLOUR is not

working properly. Then, select the "SECAM"

mode. Check again its colour so that it is work-

ing properly.

COLOUR SYSTEM key to select modes ex-

cept NTSC 4.43, check the COLOUR is not

2. Receive the SECAM colour bar signal, select

working properly. Then, select the "NTSC 4.43"

3. Receive the NTSC 4.43 signal, select the

mode. Check again its colour so that it is work-

ing properly.

thru AV, select the COLOUR SYSTEM key to

select modes except N4.43/3.58, check the

COLOUR is not working properly. Then, se-

lect the "NTSC 4.43/3.58" mode. Check again

4. Receive the NTSC 4.43/3.58 colour bar signal

its colour so that it is working properly.

"SOUND SYSTEM" turn to B/G, I. Check the

1. Receive the PAL-D/K signal, select the

SOUND

SYSTEM

sound output is not working properly.

Select D/K and check the sound output to make

sure it is working properly.

SYSTEM" turn to B/G, D/K. Check the sound

output is not working properly.

Select I and check the sound output to make

2. Receive the PAL-I signal, select the "SOUND

sure it is working properly.

3. Receive PAL-B/G signal, select the "SOUND

SYSTEM" turn to I, D/K. Check the sound out-

put is not working properly.

Select B/G and check the sound output to

make sure it is working properly.

SYSTEM" turn to BIG, I, D/K. Check the sound

4. Receive "NTSC-M" signal, select the "SOUND

output is not working properly.

Select mode check the sound output to make

NOISE MUTE

sure the sound is heard from the speakers.

Then put the unit in no signal state.

1. Receive the PAL colour bar signal.

2. Turn up the volume control to maximum, make

sure it is working properly.

CHECKING

3. Check the sound mute is effective.

4. Finally turn sound level of CTV to minimum.

Page 12

C21-RF50S

REMARK

LAST INITIAL

SETTING DATA

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

DEFAULT RANGE

1B 00-FF

DE 00-FF

53 00-FF

3E 00-FF

00-FF

08 00-FF

00 00-3F

00 00-02

12-2

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

40 SHARPNESS-OFFSET (SECAM) 04 00-0F

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

REMARK

LAST INITIAL

SETTING DATA

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

41 SHARPNESS-OFFSET (N358) 0C 00-0F

42 SHARPNESS-OFFSET (N443) 08 00-0F

79 LAST COLOUR-G 1E 00-3C

7A LAST BRIGHTNESS-G 1E 00-3C

LAST WHITE_TEMP-G

7F FLAST PROGRAM/SOURCE 01 00-FF

7B LAST TINT-G 1E 00-3C

7C LAST SHARPNESS-G 1E 00-3C

MODEL MODEL

LETTER NO. LETTER NO.

LAST SPAT ON/OFF-G

LAST SURR ON/OFF-G

OP_A2 OP_NDF OP_MSA OP_LED_F OP_BIL OP_GAME

OP_IGR OP_NICAM OP_AN7396 OP_AN5891 OP_AN5890 OP_CP OP_IF38_0 OP_TXT_EU

OP_HP2 OP_FSL OP_RUS OP_FRE OP_CHI OP_MAL OP_ARA OP_THA

OP_SM1 OP_SM0 OP_FMWS OP_AV OP_BTSC OP_HTL OP_VMC OP_VMI

OP_FCO OP_ACL OP_OSO OP_EHT OP_EVG OP_FFI OP_AVL OP_BKS

OP_TXT_WE OP_TXT OP_FOB_AV OP_FOA_AV OP_FOB_FE OP_FOA_FE OP_AGC1 OP_AGC0

OP_FSECAM OP_FN443 OP_F358 OP_PSECAM OP_S_BG OP_S_I OP_S_DK OP_S_M

46 BM-ON 00 00-01

47 BM-EFFECT 02 00-0F

48 AGC-ON 01 00-01

49 AGC ADJUST 0 3 00-0F

4F IGR OUTPUT LEVEL 10 00-1E

50 NICAM OUTPUT LEVEL (B/G) 0D 00-1E

51 NICAM OUTPUT LEVEL (I) 12 00-1E

52 NICAM OUTPUT LEVEL (D/K) 0D 00-1E

53 NICAM LOWER ERROR LIMIT 23 00-FF

54 NICAM UPPER ERROR LIMIT 46 00-FF

55 IGR STEREO R CH GAIN ADJ. 06 00-0F

4E FM OUTPUT LEVEL 0F 00-1E

4C AGC-N 00 00-01

4D GAIN-N 00 00-1F

60 LAST VOLUME 01 00-3C

61 LAST BALANCE 1E 00-3C

62 LAST BASS 1E 00-3C

63 LAST TREBLE 1E 00-3C

64 LAST SURR ON/OFF 00 00-02

65 LAST SURROUND LEVEL 1E 00-3C

66 LAST SPAT ON/OFF 00 00-02

67 LAST SPATIALIZER LEVEL 1E 00-3C

69 LAST CONTRAST 3C 00-3C

6A LAST COLOUR 1E 00-3C

6B LAST BRIGHTNESS 1E 00-3C

6C LAST TINT 1E 00-3C

6D LAST SHARPNESS 1E 00-3C

6E LAST WHITE_TEMP 00 00-02

70 LAST BALANCE-G 1E 00-3C

71 LAST BASS-G 1E 00-3C

72 LAST TREBLE-G 1E 00-3C

74 LAST SURROUND LEVEL-G 1E 00-3C

76 LAST SPATIALIZER LEVEL-G 1E 00-3C

78 LAST CONTRAST-G 3C 00-3C

DEFAULT RANGE

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

00 PASS WORD 55 00-FF

01 PASS WORD 41 00-FF

02 PASS WORD 53 00-FF

03 PASS WORD 36 00-FF

06 AGC TAKE-OVER 0E 00-3F

07 V-SLOPE 20 00-3F

08 V-SLOPE 20 00-3F

09 V-CENTER 20 00-3F

0A H-CENTER 20 00-3F

0B H-SIZE 20 00-3F

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

MEMORY MAP

0C EW-PARALLELOGRAM 20 00-3F

01.C21-RF50S_E_p01-20 02.12.5, 12:4612

0D EW-PARABOLA/WIDTH 20 00-3F

0E EW-UPPER CORNER 20 00-3F

0F EW-LOWER CORNER 20 00-3F

10 EW-TRAPEZIUM 20 00-3F

11 HORIZONTAL-BOW 20 00-3F

12 S-CORRECTION 00 00-3F

12-1

MODEL MODEL

16 DRIVE-R (STANDARD) 20 00-3F

17 DRIVE-G (STANDARD) 20 00-3F

18 DRIVE-B (STANDARD) 20 00-3F

19 DRIVE-R (WARM) 20 00-3F

1A DRIVE-G (WARM) 20 00-3F

1B DRIVE-B (WARM) 20 00-3F

1C DRIVE-R (COOL) 19 00-3F

1D DRIVE-G (COOL) 2 0 00-3F

1E DRIVE-B (COOL) 20 00-3F

22 SUB-VOLUME 3C 00-3C

23 SUB-CONTRAST 3F 00-3F

24 SUB-COLOUR 20 00-3F

25 SUB-BRIGHTNESS 20 00-3F

26 SUB-TINT 20 00-3F

27 SUB-SHARPNESS 20 00-3F

28 HTL-VOLUME 1E 00-3C

29 HTL-PROGRAM-NUMBER FF 00-FF

2F CUTOFF LEVEL -OFFSET G 20 00-3F

30 CATHODE DRIVE LEVEL 00 00-0F

31 Y-DELAY (TV PAL) 0C 00-0F

32 Y-DELAY (TV SECAM) 0F 00-0F

33 Y-DELAY (TV N358) 0C 00-0F

34 Y-DELAY (TV N443) 0C 00-0F

35 Y-DELAY (TV BW) 0C 00-0F

36 Y-DELAY (AV PAL) 0C 00-0F

37 Y-DELAY (AV SECAM) 0F 00-0F

38 Y-DELAY (AV N358) 0C 00-0F

2E CUTOFF LEVEL -OFFSET R 20 00-3F

2C BLUE BACK CONTRAST 0A 00-0F

2D OSD-REFERENCE 0F 00-0F

39 Y-DELAY (AV N443) 0C 00-0F

3A Y-DELAY (AV BW) 0C 00-0F

3B COLOUR-OFFSET (PAL) 08 00-0F

3C COLOUR-OFFSET (SECAM) 08 00-0F

3D COLOUR-OFFSET (N358) 04 00-0F

3E COLOUR-OFFSET (N443) 04 00-0F

3F SHARPNESS-OFFSET (PAL) 08 00-0F

LETTER NO. LETTER NO.

Page 13

REMARK

LAST INITIAL

SETTING DATA

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

C21-RF50S

DEFAULT RANGE

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

C0 IGR_ST 0 IGR_ST 1 IGR_ST 2 IGR_ST 3 IGR_ST 4 IGR_ST 5 IGR_ST 6 IGR_ST 7 FF 00-FF

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

REMARK

LAST INITIAL

SETTING DATA

C1 IGR_ST 8 IGR_ST 9 IGR_ST 10 IGR_ST 11 IGR_ST 12 IGR_ST 13 IGR_ST 14 IGR_ST 15 FF 00-FF

C2 IGR_ST 16 IGR_ST 17 IGR_ST 18 IGR_ST 19 IGR_ST 20 IGR_ST 21 IGR_ST 22 IGR_ST 23 FF 00-FF

C3 IGR_ST 24 IGR_ST 25 IGR_ST 26 IGR_ST 27 IGR_ST 28 IGR_ST 29 IGR_ST 30 IGR_ST 31 FF 00-FF

C4 IGR_ST 32 IGR_ST 33 IGR_ST 34 IGR_ST 35 IGR_ST 36 IGR_ST 37 IGR_ST 38 IGR_ST 39 FF 00-FF

C5 IGR_ST 40 IGR_ST 41 IGR_ST 42 IGR_ST 43 IGR_ST 44 IGR_ST 45 IGR_ST 46 IGR_ST 47 FF 00-FF

C6 IGR_ST 48 IGR_ST 49 IGR_ST 50 IGR_ST 51 IGR_ST 52 IGR_ST 53 IGR_ST 54 IGR_ST 55 FF 00-FF

C7 IGR_ST 56 IGR_ST 57 IGR_ST 58 IGR_ST 59 IGR_ST 60 IGR_ST 61 IGR_ST 62 IGR_ST 63 FF 00-FF

C8 IGR_ST 64 IGR_ST 65 IGR_ST 66 IGR_ST 67 IGR_ST 68 IGR_ST 69 IGR_ST 70 IGR_ST 71 FF 00-FF

C9 IGR_ST 72 IGR_ST 73 IGR_ST 74 IGR_ST 75 IGR_ST 76 IGR_ST 77 IGR_ST 78 IGR_ST 79 FF 00-FF

CA IGR_ST 80 IGR_ST 81 IGR_ST 82 IGR_ST 83 IGR_ST 84 IGR_ST 85 IGR_ST 86 IGR_ST 87 FF 00-FF

CB IGR_ST 88 IGR_ST 89 IGR_ST 90 IGR_ST 91 IGR_ST 92 IGR_ST 93 IGR_ST 94 IGR_ST 95 FF 00-FF

CC IGR_ST 96 IGR_ST 97 IGR_ST 98 IGR_ST 99 FF 00-FF

13-2

MODEL MODEL

F0 NIC_MA 24 NIC_MA 25 NIC_MA 26 NIC_MA 27 NIC_MA 28 NIC_MA 29 NIC_MA 30 NIC_MA 31 FF 00-FF

F1 NIC_MA 32 NIC_MA 33 NIC_MA 34 NIC_MA 35 NIC_MA 36 NIC_MA 37 NIC_MA 38 NIC_MA 39 FF 00-FF

F2 NIC_MA 40 NIC_MA 41 NIC_MA 42 NIC_MA 43 NIC_MA 44 NIC_MA 45 NIC_MA 46 NIC_MA 47 FF 00-FF

F3 NIC_MA 48 NIC_MA 49 NIC_MA 50 NIC_MA 51 NIC_MA 52 NIC_MA 53 NIC_MA 54 NIC_MA 55 FF 00-FF

F4 NIC_MA 56 NIC_MA 57 NIC_MA 58 NIC_MA 59 NIC_MA 60 NIC_MA 61 NIC_MA 62 NIC_MA 63 FF 00-FF

F5 NIC_MA 64 NIC_MA 65 NIC_MA 66 NIC_MA 67 NIC_MA 68 NIC_MA 69 NIC_MA 70 NIC_MA 71 FF 00-FF

F6 NIC_MA 72 NIC_MA 73 NIC_MA 74 NIC_MA 75 NIC_MA 76 NIC_MA 77 NIC_MA 78 NIC_MA 79 FF 00-FF

F7 NIC_MA 80 NIC_MA 81 NIC_MA 82 NIC_MA 83 NIC_MA 84 NIC_MA 85 NIC_MA 86 NIC_MA 87 FF 00-FF

F8 NIC_MA 88 NIC_MA 89 NIC_MA 90 NIC_MA 91 NIC_MA 92 NIC_MA 93 NIC_MA 94 NIC_MA 95 FF 00-FF

E0 NIC_ST 16 NIC_ST 17 NIC_ST 18 NIC_ST 19 NIC_ST 20 NIC_ST 21 NIC_ST 22 NIC_ST 23 FF 00-FF

E1 NIC_ST 24 NIC_ST 25 NIC_ST 26 NIC_ST 27 NIC_ST 28 NIC_ST 29 NIC_ST 30 NIC_ST 31 FF 00-FF

E2 NIC_ST 32 NIC_ST 33 NIC_ST 34 NIC_ST 35 NIC_ST 36 NIC_ST 37 NIC_ST 38 NIC_ST 39 FF 00-FF

E3 NIC_ST 40 NIC_ST 41 NIC_ST 42 NIC_ST 43 NIC_ST 44 NIC_ST 45 NIC_ST 46 NIC_ST 47 FF 00-FF

E4 NIC_ST 48 NIC_ST 49 NIC_ST 50 NIC_ST 51 NIC_ST 52 NIC_ST 53 NIC_ST 54 NIC_ST 55 FF 00-FF

E5 NIC_ST 56 NIC_ST 57 NIC_ST 58 NIC_ST 59 NIC_ST 60 NIC_ST 61 NIC_ST 62 NIC_ST 63 FF 00-FF

E6 NIC_ST 64 NIC_ST 65 NIC_ST 66 NIC_ST 67 NIC_ST 68 NIC_ST 69 NIC_ST 70 NIC_ST 71 FF 00-FF

E7 NIC_ST 72 NIC_ST 73 NIC_ST 74 NIC_ST 75 NIC_ST 76 NIC_ST 77 NIC_ST 78 NIC_ST 79 FF 00-FF

E8 NIC_ST 80 NIC_ST 81 NIC_ST 82 NIC_ST 83 NIC_ST 84 NIC_ST 85 NIC_ST 86 NIC_ST 87 FF 00-FF

D0 IGR_MA 8 IGR_MA 9 IGR_MA 10 IGR_MA 11 IGR_MA 12 IGR_MA 13 IGR_MA 14 IGR_MA 15 FF 00-FF

D1 IGR_MA 16 IGR_MA 17 IGR_MA 18 IGR_MA 19 IGR_MA 20 IGR_MA 21 IGR_MA 22 IGR_MA 23 FF 00-FF

D2 IGR_MA 24 IGR_MA 25 IGR_MA 26 IGR_MA 27 IGR_MA 28 IGR_MA 29 IGR_MA 30 IGR_MA 31 FF 00-FF

D3 IGR_MA 32 IGR_MA 33 IGR_MA 34 IGR_MA 35 IGR_MA 36 IGR_MA 37 IGR_MA 38 IGR_MA 39 FF 00-FF

D4 IGR_MA 40 IGR_MA 41 IGR_MA 42 IGR_MA 43 IGR_MA 44 IGR_MA 45 IGR_MA 46 IGR_MA 47 FF 00-FF

D5 IGR_MA 48 IGR_MA 49 IGR_MA 50 IGR_MA 51 IGR_MA 52 IGR_MA 53 IGR_MA 54 IGR_MA 55 FF 00-FF

D6 IGR_MA 56 IGR_MA 57 IGR_MA 58 IGR_MA 59 IGR_MA 60 IGR_MA 61 IGR_MA 62 IGR_MA 63 FF 00-FF

D7 IGR_MA 64 IGR_MA 65 IGR_MA 66 IGR_MA 67 IGR_MA 68 IGR_MA 69 IGR_MA 70 IGR_MA 71 FF 00-FF

D8 IGR_MA 72 IGR_MA 73 IGR_MA 74 IGR_MA 75 IGR_MA 76 IGR_MA 77 IGR_MA 78 IGR_MA 79 FF 00-FF

CF IGR_MA 0 IGR_MA 1 IGR_MA 2 IGR_MA 3 IGR_MA 4 IGR_MA 5 IGR_MA 6 IGR_MA 7 FF 00-FF

D9 IGR_MA 80 IGR_MA 81 IGR_MA 82 IGR_MA 83 IGR_MA 84 IGR_MA 85 IGR_MA 86 IGR_MA 87 FF 00-FF

DA IGR_MA 88 IGR_MA 89 IGR_MA 90 IGR_MA 91 IGR_MA 92 IGR_MA 93 IGR_MA 94 IGR_MA 95 FF 00-FF

DB IGR_MA 96 IGR_MA 97 IGR_MA 98 IGR_MA 99 FF 00-FF

DE NIC_ST 0 NIC_ST 1 NIC_ST 2 NIC_ST 3 NIC_ST 4 NIC_ST 5 NIC_ST 6 NIC_ST 7 FF 00-FF

DF NIC_ST 8 NIC_ST 9 NIC_ST 10 NIC_ST 11 NIC_ST 12 NIC_ST 13 NIC_ST 14 NIC_ST 15 FF 00-FF

E9 NIC_ST 88 NIC_ST 89 NIC_ST 90 NIC_ST 91 NIC_ST 92 NIC_ST 93 NIC_ST 94 NIC_ST 95 FF 00-FF

EA NIC_ST 96 NIC_ST 97 NIC_ST 98 NIC_ST 99 FF 00-FF

EF NIC_MA 16 NIC_MA 17 NIC_MA 18 NIC_MA 19 NIC_MA 20 NIC_MA 21 NIC_MA 22 NIC_MA 23 FF 00-FF

ED NIC_MA 0 NIC_MA 1 NIC_MA 2 NIC_MA 3 NIC_MA 4 NIC_MA 5 NIC_MA 6 NIC_MA 7 FF 00-FF

EE NIC_MA 8 NIC_MA 9 NIC_MA 10 NIC_MA 11 NIC_MA 12 NIC_MA 13 NIC_MA 14 NIC_MA 15 FF 00-FF

F9 NIC_MA 96 NIC_MA 97 NIC_MA 98 NIC_MA 99 FF 00-FF

FF NIC_3D 24 NIC_3D 25 NIC_3D 26 NIC_3D 27 NIC_3D 28 NIC_3D 29 NIC_3D 30 NIC_3D 31 00 00-FF

FE NIC_3D 16 NIC_3D 17 NIC_3D 18 NIC_3D 19 NIC_3D 20 NIC_3D 21 NIC_3D 22 NIC_3D 23 00 00-FF

FC NIC_3D 0 NIC_3D 1 NIC_3D 2 NIC_3D 3 NIC_3D 4 NIC_3D 5 NIC_3D 6 NIC_3D 7 00 00-FF

FD NIC_3D 8 NIC_3D 9 NIC_3D 10 NIC_3D 11 NIC_3D 12 NIC_3D 13 NIC_3D 14 NIC_3D 15 00 00-FF

LETTER NO. LETTER NO.

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

DEFAULT RANGE

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

80 FAVOURITE PROGRAM RED 0A 00-FF

81 FAVOURITE PROGRAM GREEN 14 00-FF

82 FAVOURITE PROGRAM YELLOW 1E 00-FF

83 FAVOURITE PROGRAM CYAN 28 00-FF

86 POWER 01 00-01

87 B_BACK 00 00-01

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

88 LANGUAGE 00 00-06

01.C21-RF50S_E_p01-20 02.12.5, 12:4613

89 DIGIT 01 00-01

00 00-01

FF 00-FF

13-1

TMR_FLAG

NICAM 0 NICAM 1 NICAM 2 NICAM 3 NICAM 4 NICAM 5 NICAM 6 NICAM 7

NICAM 8 NICAM 9 NICAM 10 NICAM 11 NICAM 12 NICAM 13 NICAM 14 NICAM 15

NICAM 16 NICAM 17 NICAM 18 NICAM 19 NICAM 20 NICAM 21 NICAM 22 NICAM 23

NICAM 24 NICAM 25 NICAM 26 NICAM 27 NICAM 28 NICAM 29 NICAM 30 NICAM 31

NICAM 32 NICAM 33 NICAM 34 NICAM 35 NICAM 36 NICAM 37 NICAM 38 NICAM 39

NICAM 40 NICAM 41 NICAM 42 NICAM 43 NICAM 44 NICAM 45 NICAM 46 NICAM 47

NICAM 48 NICAM 49 NICAM 50 NICAM 51 NICAM 52 NICAM 53 NICAM 54 NICAM 55

NICAM 56 NICAM 57 NICAM 58 NICAM 59 NICAM 60 NICAM 61 NICAM 62 NICAM 63

NICAM 64 NICAM 65 NICAM 66 NICAM 67 NICAM 68 NICAM 69 NICAM 70 NICAM 71

NICAM 72 NICAM 73 NICAM 74 NICAM 75 NICAM 76 NICAM 77 NICAM 78 NICAM 79

8F FADE IN VOLUME FF 00-FF

93 SKIP 0 SKIP 1 SKIP 2 SKIP 3 SKIP 4 SKIP 5 SKIP 6 SKIP 7 80 00-FF

94 SKIP 8 SKIP 9 SKIP 10 SKIP 11 SKIP 12 SKIP 13 SKIP 14 SKIP 15 00 00-FF

95 SKIP 16 SKIP 17 SKIP 18 SKIP 19 SKIP 20 SKIP 21 SKIP 22 SKIP 23 00 00-FF

96 SKIP 24 SKIP 25 SKIP 26 SKIP 27 SKIP 28 SKIP 29 SKIP 30 SKIP 31 00 00-FF

97 SKIP 32 SKIP 33 SKIP 34 SKIP 35 SKIP 36 SKIP 37 SKIP 38 SKIP 39 00 00-FF

98 SKIP 40 SKIP 41 SKIP 42 SKIP 43 SKIP 44 SKIP 45 SKIP 46 SKIP 47 00 00-FF

8E ON TIMER 00 00-4D

8C REMINDER 00 00-4D

8D OFF TIMER 00 00-4D

99 SKIP 48 SKIP 49 SKIP 50 SKIP 51 SKIP 52 SKIP 53 SKIP 54 SKIP 55 00 00-FF

9A SKIP 56 SKIP 57 SKIP 58 SKIP 59 SKIP 60 SKIP 61 SKIP 62 SKIP 63 00 00-FF

9B SKIP 64 SKIP 65 SKIP 66 SKIP 67 SKIP 68 SKIP 69 SKIP 70 SKIP 71 00 00-FF

9C SKIP 72 SKIP 73 SKIP 74 SKIP 75 SKIP 76 SKIP 77 SKIP 78 SKIP 79 00 00-FF

9D SKIP 80 SKIP 81 SKIP 82 SKIP 83 SKIP 84 SKIP 85 SKIP 86 SKIP 87 00 00-FF

9E SKIP 88 SKIP 89 SKIP 90 SKIP 91 SKIP 92 SKIP 93 SKIP 94 SKIP 95 00 00-FF

9F SKIP 96 SKIP 97 SKIP 98 SKIP 99 00 00-FF

A2 IGR 0 IGR 1 IGR 2 IGR 3 IGR 4 IGR 5 IGR 6 IGR 7 FF 00-FF

A3 IGR 8 IGR 9 IGR 10 IGR 11 IGR 12 IGR 13 IGR 14 IGR 15 FF 00-FF

A4 IGR 16 IGR 17 IGR 18 IGR 19 IGR 20 IGR 21 IGR 22 IGR 23 FF 00-FF

A5 IGR 24 IGR 25 IGR 26 IGR 27 IGR 28 IGR 29 IGR 30 IGR 31 FF 00-FF

A6 IGR 32 IGR 33 IGR 34 IGR 35 IGR 36 IGR 37 IGR 38 IGR 39 FF 00-FF

A7 IGR 40 IGR 41 IGR 42 IGR 43 IGR 44 IGR 45 IGR 46 IGR 47 FF 00-FF

A8 IGR 48 IGR 49 IGR 50 IGR 51 IGR 52 IGR 53 IGR 54 IGR 55 FF 00-FF

A9 IGR 56 IGR 57 IGR 58 IGR 59 IGR 60 IGR 61 IGR 62 IGR 63 FF 00-FF

AA IGR 64 IGR 65 IGR 66 IGR 67 IGR 68 IGR 69 IGR 70 IGR 71 FF 00-FF

AB IGR 72 IGR 73 IGR 74 IGR 75 IGR 76 IGR 77 IGR 78 IGR 79 FF 00-FF

AC IGR 80 IGR 81 IGR 82 IGR 83 IGR 84 IGR 85 IGR 86 IGR 87 FF 00-FF

AD IGR 88 IGR 89 IGR 90 IGR 91 IGR 92 IGR 93 IGR 94 IGR 95 FF 00-FF

AE IGR 96 IGR 97 IGR 98 IGR 99 FF 00-FF

NICAM 80 NICAM 81 NICAM 82 NICAM 83 NICAM 84 NICAM 85 NICAM 86 NICAM 87

NICAM 88 NICAM 89 NICAM 90 NICAM 91 NICAM 92 NICAM 93 NICAM 94 NICAM 95

NICAM 96 NICAM 97 NICAM 98 NICAM 99

MODEL MODEL

LETTER NO. LETTER NO.

Page 14

C21-RF50S

REMARK

LAST INITIAL

SETTING DATA

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

DEFAULT RANGE

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

140 S-SYS AFT (auto) C-SYS 10

141 TUNING FREQUANCY (HIGHER PART) POS 13

142 TUNING FREQUANCY (LOWER PART)

143 S-SYS AFT (auto) C-SYS 10

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

REMARK

LAST INITIAL

SETTING DATA

144 TUNING FREQUANCY (HIGHER PART) POS 14

145 TUNING FREQUANCY (LOWER PART)

146 S-SYS AFT (auto) C-SYS 10

147 TUNING FREQUANCY (HIGHER PART) POS 15

148 TUNING FREQUANCY (LOWER PART)

149 S-SYS AFT (auto) C-SYS 10

14F S-SYS AFT (auto) C-SYS 10

14A TUNING FREQUANCY (HIGHER PART) POS 16

14B TUNING FREQUANCY (LOWER PART) -

14C S-SYS AFT (auto) C-SYS 10

14D TUNING FREQUANCY (HIGHER PART) POS 17

14E TUNING FREQUANCY (LOWER PART)

150 TUNING FREQUANCY (HIGHER PART) POS 18

151 TUNING FREQUANCY (LOWER PART)

152 S-SYS AFT (auto) C-SYS 10

153 TUNING FREQUANCY (HIGHER PART) POS 19

154 TUNING FREQUANCY (LOWER PART)

155 S-SYS AFT (auto) C-SYS 10

156 TUNING FREQUANCY (HIGHER PART) POS 20

157 TUNING FREQUANCY (LOWER PART)

158 S-SYS AFT (auto) C-SYS 10

159 TUNING FREQUANCY (HIGHER PART) POS 21

15A TUNING FREQUANCY (LOWER PART)

160 TUNING FREQUANCY (LOWER PART)

161 S-SYS AFT (auto) C-SYS 10

162 TUNING FREQUANCY (HIGHER PART) POS 24

163 TUNING FREQUANCY (LOWER PART)

15F TUNING FREQUANCY (HIGHER PART) POS 23

15B S-SYS AFT (auto) C-SYS 10

15C TUNING FREQUANCY (HIGHER PART) POS 22

15D TUNING FREQUANCY (LOWER PART)

15E S-SYS AFT (auto) C-SYS 10

164 S-SYS AFT (auto) C-SYS 10

165 TUNING FREQUANCY (HIGHER PART) POS 25

166 TUNING FREQUANCY (LOWER PART)

167 S-SYS AFT (auto) C-SYS 10

168 TUNING FREQUANCY (HIGHER PART) POS 26

169 TUNING FREQUANCY (LOWER PART)

16A S-SYS AFT (auto) C-SYS 10

16B TUNING FREQUANCY (HIGHER PART) POS 27

16C TUNING FREQUANCY (LOWER PART)

16D S-SYS AFT (auto) C-SYS 10

170 S-SYS AFT (auto) C-SYS 10

171 TUNING FREQUANCY (HIGHER PART) POS 29

172 TUNING FREQUANCY (LOWER PART)

173 S-SYS AFT (auto) C-SYS 10

174 TUNING FREQUANCY (HIGHER PART) POS 30

175 TUNING FREQUANCY (LOWER PART)

176 S-SYS AFT (auto) C-SYS 10

177 TUNING FREQUANCY (HIGHER PART) POS 31

16F TUNING FREQUANCY (LOWER PART)

16E TUNING FREQUANCY (HIGHER PART) POS 28

178 TUNING FREQUANCY (LOWER PART)

MODEL MODEL

179 S-SYS AFT (auto) C-SYS 10

17F S-SYS AFT (auto) C-SYS 10

17A TUNING FREQUANCY (HIGHER PART) POS 32

17B TUNING FREQUANCY (LOWER PART)

17C S-SYS AFT (auto) C-SYS 10

17D TUNING FREQUANCY (HIGHER PART) POS 33

17E TUNING FREQUANCY (LOWER PART)

14-2

LETTER NO. LETTER NO.

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

DEFAULT RANGE

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

100 NIC_3D 32 NIC_3D 33 NIC_3D 34 NIC_3D 35 NIC_3D 36 NIC_3D 37 NIC_3D 38 NIC_3D 39 00 00-FF

101 NIC_3D 40 NIC_3D 41 NIC_3D 42 NIC_3D 43 NIC_3D 44 NIC_3D 45 NIC_3D 46 NIC_3D 47 00 00-FF

102 NIC_3D 48 NIC_3D 49 NIC_3D 50 NIC_3D 51 NIC_3D 52 NIC_3D 53 NIC_3D 54 NIC_3D 55 00 00-FF

103 NIC_3D 56 NIC_3D 57 NIC_3D 58 NIC_3D 59 NIC_3D 60 NIC_3D 61 NIC_3D 62 NIC_3D 63 00 00-FF

104 NIC_3D 64 NIC_3D 65 NIC_3D 66 NIC_3D 67 NIC_3D 68 NIC_3D 69 NIC_3D 70 NIC_3D 71 00 00-FF

105 NIC_3D 72 NIC_3D 73 NIC_3D 74 NIC_3D 75 NIC_3D 76 NIC_3D 77 NIC_3D 78 NIC_3D 79 00 00-FF

106 NIC_3D 80 NIC_3D 81 NIC_3D 82 NIC_3D 83 NIC_3D 84 NIC_3D 85 NIC_3D 86 NIC_3D 87 00 00-FF

107 NIC_3D 88 NIC_3D 89 NIC_3D 90 NIC_3D 91 NIC_3D 92 NIC_3D 93 NIC_3D 94 NIC_3D 95 00 00-FF

108 NIC_3D 96 NIC_3D 97 NIC_3D 98 NIC_3D 99 00 00-FF

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

109

10F NIC_MO 32 NIC_MO 33 NIC_MO 34 NIC_MO 35 NIC_MO 36 NIC_MO 37 NIC_MO 38 NIC_MO 39 FF 00-FF

10A

10B NIC_MO 0 NIC_MO 1 NIC_MO 2 NIC_MO 3 NIC_MO 4 NIC_MO 5 NIC_MO 6 NIC_MO 7 FF 00-FF

10C NIC_MO 8 NIC_MO 9 NIC_MO 10 NIC_MO 11 NIC_MO 12 NIC_MO 13 NIC_MO 14 NIC_MO 15 FF 00-FF

10D NIC_MO 16 NIC_MO 17 NIC_MO 18 NIC_MO 19 NIC_MO 20 NIC_MO 21 NIC_MO 22 NIC_MO 23 FF 00-FF

10E NIC_MO 24 NIC_MO 25 NIC_MO 26 NIC_MO 27 NIC_MO 28 NIC_MO 29 NIC_MO 30 NIC_MO 31 FF 00-FF

01.C21-RF50S_E_p01-20 02.12.5, 12:4614

110 NIC_MO 40 NIC_MO 41 NIC_MO 42 NIC_MO 43 NIC_MO 44 NIC_MO 45 NIC_MO 46 NIC_MO 47 FF 00-FF

111 NIC_MO 48 NIC_MO 49 NIC_MO 50 NIC_MO 51 NIC_MO 52 NIC_MO 53 NIC_MO 54 NIC_MO 55 FF 00-FF

112 NIC_MO 56 NIC_MO 57 NIC_MO 58 NIC_MO 59 NIC_MO 60 NIC_MO 61 NIC_MO 62 NIC_MO 63 FF 00-FF

113 NIC_MO 64 NIC_MO 65 NIC_MO 66 NIC_MO 67 NIC_MO 68 NIC_MO 69 NIC_MO 70 NIC_MO 71 FF 00-FF

114 NIC_MO 72 NIC_MO 73 NIC_MO 74 NIC_MO 75 NIC_MO 76 NIC_MO 77 NIC_MO 78 NIC_MO 79 FF 00-FF

115 NIC_MO 80 NIC_MO 81 NIC_MO 82 NIC_MO 83 NIC_MO 84 NIC_MO 85 NIC_MO 86 NIC_MO 87 FF 00-FF

116 NIC_MO 88 NIC_MO 89 NIC_MO 90 NIC_MO 91 NIC_MO 92 NIC_MO 93 NIC_MO 94 NIC_MO 95 FF 00-FF

117 NIC_MO 96 NIC_MO 97 NIC_MO 98 NIC_MO 99 FF 00-FF

14-1

MODEL MODEL

11 ATUNING FREQUANCY (HIGHER PART) S-SYS POS 0

11 BTUNING FREQUANCY (LOWER PART) 000:BG

118

11 DTUNING FREQUANCY (HIGHER PART O1O:DK POS 1

119

11C S-SYS AFT (auto) C-SYS 10 001:I

11E TUNING FREQUANCY (LOWER PART) 011:M

120 TUNING FREQUANCY (HIGHER PART) AFT POS 2

121 TUNING FREQUANCY (LOWER PART) 0:OFF

122 S-SYS AFT (auto) C-SYS 10 1:ON

123 TUNING FREQUANCY (HIGHER PART) PO 3

124 TUNING FREQUANCY (LOWER PART)

125 S-SYS AFT (auto) C-SYS 10

126 TUNING FREQUANCY (HIGHER PART) POS 4

127 TUNING FREQUANCY (LOWER PART)

128 S-SYS AFT (auto) C-SYS 10

11F S-SYS AFT (auto) C-SYS 10

129 TUNING FREQUANCY (HIGHER PART) POS 5

12A TUNING FREQUANCY (LOWER PART)

12B S-SYS AFT (auto) C-SYS 10

130 TUNING FREQUANCY (LOWER PART)

131 S-SYS AFT (auto) C-SYS 10

132 TUNING FREQUANCY (HIGHER PART) POS 8

133 TUNING FREQUANCY (LOWER PART)

134 S-SYS AFT (auto) C-SYS 10

135 TUNING FREQUANCY (HIGHER PART) POS 9

12F TUNING FREQUANCY (HIGHER PART) POS 7

12C TUNING FREQUANCY (HIGHER PART) POS 6

12D TUNING FREQUANCY (LOWER PART)

12E S-SYS AFT (auto) C-SYS 10

136 TUNING FREQUANCY (LOWER PART)

137 S-SYS AFT (auto) C-SYS 10

138 TUNING FREQUANCY (HIGHER PART) POS 10

139 TUNING FREQUANCY (LOWER PART)

13F TUNING FREQUANCY (LOWER PART)

13A S-SYS AFT (auto) C-SYS 10

13B TUNING FREQUANCY (HIGHER PART) POS 11

13C TUNING FREQUANCY (LOWER PART)

13D S-SYS AFT (auto) C-SYS 10

13E TUNING FREQUANCY (HIGHER PART) POS 12

LETTER NO. LETTER NO.

Page 15

REMARK

LAST INITIAL

SETTING DATA

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

C21-RF50S

DEFAULT RANGE

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

1C0 TUNING FREQUANCY (LOWER PART) POS 55

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

REMARK

LAST INITIAL

SETTING DATA

1C1 S-SYS AFT (auto) C-SYS 10

1C2 TUNING FREQUANCY (HIGHER PART) POS 56

1C3 TUNING FREQUANCY (LOWER PART)

1C4 S-SYS AFT (auto) C-SYS 10

1C5 TUNING FREQUANCY (HIGHER PART) POS 57

1C6 TUNING FREQUANCY (LOWER PART)

1C7 S-SYS AFT (auto) C-SYS 10

1C8 TUNING FREQUANCY (HIGHER PART) POS 58

1C9 TUNING FREQUANCY (LOWER PART)

1CA S-SYS AFT (auto) C-SYS 10

1D0 S-SYS AFT (auto) C-SYS 10

1D1 TUNING FREQUANCY (HIGHER PART) POS 61

1D2 TUNING FREQUANCY (LOWER PART)

1D3 S-SYS AFT (auto) C-SYS 10

1CF TUNING FREQUANCY (LOWER PART)

1CB TUNING FREQUANCY (HIGHER PART) POS 59

1CE TUNING FREQUANCY (HIGHER PART) POS 60

1CC TUNING FREQUANCY (LOWER PART)

1CD S-SYS AFT (auto) C-SYS 10

1D4 TUNING FREQUANCY (HIGHER PART) POS 62

1D5 TUNING FREQUANCY (LOWER PART)

1D6 S-SYS AFT (auto) C-SYS 10

1D7 TUNING FREQUANCY (HIGHER PART) POS 63

1D8 TUNING FREQUANCY (LOWER PART)

1D9 S-SYS AFT (auto) C-SYS 10

1DA TUNING FREQUANCY (HIGHER PART) POS 64

1DB TUNING FREQUANCY (LOWER PART)

1E0 TUNING FREQUANCY (HIGHER PART) POS 66

1DF S-SYS AFT (auto) C-SYS 10

1DE TUNING FREQUANCY (LOWER PART)

1DC S-SYS AFT (auto) C-SYS 10

1DD TUNING FREQUANCY (HIGHER PART) POS 65

1E1 TUNING FREQUANCY (LOWER PART)

1E2 S-SYS AFT (auto) C-SYS 10

1E3 TUNING FREQUANCY (HIGHER PART) POS 67

1E4 TUNING FREQUANCY (LOWER PART)

1E5 S-SYS AFT (auto) C-SYS 10

1E6 TUNING FREQUANCY (HIGHER PART) POS 68

1E7 TUNING FREQUANCY (LOWER PART)

1E8 S-SYS AFT (auto) C-SYS 10

1E9 TUNING FREQUANCY (HIGHER PART) POS 69

1EA TUNING FREQUANCY (LOWER PART)

1EB S-SYS AFT (auto) C-SYS 10

1EC TUNING FREQUANCY (HIGHER PART) POS 70

1F0 TUNING FREQUANCY (LOWER PART)

1F1 S-SYS AFT (auto) C-SYS 10

1F2 TUNING FREQUANCY (HIGHER PART) POS 72

1F3 TUNING FREQUANCY (LOWER PART)

1F4 S-SYS AFT (auto) C-SYS 10

1F5 TUNING FREQUANCY (HIGHER PART) POS 73

1F6 TUNING FREQUANCY (LOWER PART)

1F7 S-SYS AFT (auto) C-SYS 10

1EF TUNING FREQUANCY (HIGHER PART) POS 71

1EE S-SYS AFT (auto) C-SYS 10

1ED TUNING FREQUANCY (LOWER PART)

1F8 TUNING FREQUANCY (HIGHER PART) POS 74

MODEL MODEL

1F9 TUNING FREQUANCY (LOWER PART)

1FA S-SYS AFT (auto) C-SYS 10

1FB TUNING FREQUANCY (HIGHER PART) POS 75

1FE TUNING FREQUANCY (HIGHER PART) POS 76

1FF TUNING FREQUANCY (LOWER PART)

1FC TUNING FREQUANCY (LOWER PART)

1FD S-SYS AFT (auto) C-SYS 10

15-2

LETTER NO. LETTER NO.

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

DEFAULT RANGE

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

180 TUNING FREQUANCY (HIGHER PART) POS 34

181 TUNING FREQUANCY (LOWER PART)

182 S-SYS AFT (auto) C-SYS 10

183 TUNING FREQUANCY (HIGHER PART) POS 35

184 TUNING FREQUANCY (LOWER PART)

185 S-SYS AFT (auto) C-SYS 10

186 TUNING FREQUANCY (HIGHER PART) POS 36

187 TUNING FREQUANCY (LOWER PART)

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

188 S-SYS AFT (auto) C-SYS 10

01.C21-RF50S_E_p01-20 02.12.5, 12:4615

189 TUNING FREQUANCY (HIGHER PART) POS 37

18A TUNING FREQUANCY (LOWER PART)

190 TUNING FREQUANCY (LOWER PART)

191 S-SYS AFT (auto) C-SYS 10

192 TUNING FREQUANCY (HIGHER PART) POS 40

18F TUNING FREQUANCY (HIGHER PART) POS 39

18B S-SYS AFT (auto) C-SYS 10

18C TUNING FREQUANCY (HIGHER PART) POS 38

18D TUNING FREQUANCY (LOWER PART)

18E S-SYS AFT (auto) C-SYS 10

193 TUNING FREQUANCY (LOWER PART)

194 S-SYS AFT (auto) C-SYS 10

195 TUNING FREQUANCY (HIGHER PART) POS 41

196 TUNING FREQUANCY (LOWER PART)

197 S-SYS AFT (auto) C-SYS 10

198 TUNING FREQUANCY (HIGHER PART) POS 42

199 TUNING FREQUANCY (LOWER PART)

19A S-SYS AFT (auto) C-SYS 10

19B TUNING FREQUANCY (HIGHER PART) POS 43

19C TUNING FREQUANCY (LOWER PART)

19D S-SYS AFT (auto) C-SYS 10

19E TUNING FREQUANCY (HIGHER PART) POS 44

19F TUNING FREQUANCY (LOWER PART)

1A0 S-SYS AFT (auto) C-SYS 10

1A1 TUNING FREQUANCY (HIGHER PART) POS 45

1A2 TUNING FREQUANCY (LOWER PART)

1A3 S-SYS AFT (auto) C-SYS 10

1A4 TUNING FREQUANCY (HIGHER PART) POS 46

1A5 TUNING FREQUANCY (LOWER PART)

1A6 S-SYS AFT (auto) C-SYS 10

1A7 TUNING FREQUANCY (HIGHER PART) POS 47

1A8 TUNING FREQUANCY (LOWER PART)

1A9 S-SYS AFT (auto) C-SYS 10

1AA TUNING FREQUANCY (HIGHER PART) POS 48

1AF S-SYS AFT (auto) C-SYS 10

1B0 TUNING FREQUANCY (HIGHER PART) POS 50

1B1 TUNING FREQUANCY (LOWER PART)

1B2 S-SYS AFT (auto) C-SYS 10

1B3 TUNING FREQUANCY (HIGHER PART) POS 51

1B4 TUNING FREQUANCY (LOWER PART)

1AB TUNING FREQUANCY (LOWER PART)

1AE TUNING FREQUANCY (LOWER PART)

1AC S-SYS AFT (auto) C-SYS 10

1AD TUNING FREQUANCY (HIGHER PART) POS 49

1B5 S-SYS AFT (auto) C-SYS 10

MODEL MODEL

1B6 TUNING FREQUANCY (HIGHER PART) POS 52

1B7 TUNING FREQUANCY (LOWER PART)

1B8 S-SYS AFT (auto) C-SYS 10

1B9 TUNING FREQUANCY (HIGHER PART) POS 53

1BF TUNING FREQUANCY (HIGHER PART) POS 55

1BA TUNING FREQUANCY (LOWER PART)

1BB S-SYS AFT (auto) C-SYS 10

1BE S-SYS AFT (auto) C-SYS 10

1BC TUNING FREQUANCY (HIGHER PART) POS 54

1BD TUNING FREQUANCY (LOWER PART)

15-1

LETTER NO. LETTER NO.

Page 16

C21-RF50S

REMARK

LAST INITIAL

SETTING DATA

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

DEFAULT RANGE

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

00 00-02

DEFAULT SURR ON-OFF-G

16-2

240 TUNING FREQUANCY (HIGHER PART) POS 98

241 TUNING FREQUANCY (LOWER PART)

242 S-SYS AFT (auto) C-SYS 10

243 TUNING FREQUANCY (HIGHER PART) POS 99

244 TUNING FREQUANCY (LOWER PART)

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

REMARK

LAST INITIAL

SETTING DATA

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

DEFAULT RANGE

245 S-SYS AFT (auto) C-SYS 10

MODEL MODEL

246 AV1

247

248 (auto) C-SYS 10

249 AV2

24A

24B (auto) C-SYS 10

24C GAME

250

251 DEFAULT BALANCE-G 1E 00-3C

252 DEFAULT BASS-G 1E 00-3C

253 DEFAULT TREBLE-G 1E 00-3C

254

255 DEFAULT SURROUND LEVEL-G 1E 00-3C

256

257 DEFAULT SPATIALIZER LEVEL-G 1E 00-3C

258

24F

24D

24E (auto) C-SYS 10

259 DEFAULT CONTRAST-G 3C 00-3C

25A DEFAULT COLOUR-G 1E 00-3C

25B DEFAULT BRIGHTNESS-G 1E 00-3C

25C DEFAULT TINT-G 1E 00-3C

25D DEFAULT SHARPNESS-G 1E 00-3C

25E DEFAULT WHITE TEMP-G 00 00-02

260

261

262

263

264

265

266

267

268

25F

269

26A

26B

270

271

272

273

274

275

276

277

278

26F

26C

26D

26E

279

27F

27A

27B

27C

27D

27E

LETTER NO. LETTER NO.

16-1

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

201 TUNING FREQUANCY (HIGHER PART) POS 77

202 TUNING FREQUANCY (LOWER PART)

203 S-SYS AFT (auto) C-SYS 10

204 TUNING FREQUANCY (HIGHER PART) POS 78

205 TUNING FREQUANCY (LOWER PART)

206 S-SYS AFT (auto) C-SYS 10

207 TUNING FREQUANCY (HIGHER PART) POS 79

208 TUNING FREQUANCY (LOWER PART)

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

* 200 S-SYS AFT (auto) C-SYS 10

209 S-SYS AFT (auto) C-SYS 10

20F S-SYS AFT (auto) C-SYS 10

20A TUNING FREQUANCY (HIGHER PART) POS 80

20B TUNING FREQUANCY (LOWER PART)

20C S-SYS AFT (auto) C-SYS 10

20D TUNING FREQUANCY (HIGHER PART) POS 81

20E TUNING FREQUANCY (LOWER PART)

01.C21-RF50S_E_p01-20 02.12.5, 12:4616

210 TUNING FREQUANCY (HIGHER PART) POS 82

211 TUNING FREQUANCY (LOWER PART)

212 S-SYS AFT (auto) C-SYS 10

213 TUNING FREQUANCY (HIGHER PART) POS 83

214 TUNING FREQUANCY (LOWER PART)

215 S-SYS AFT (auto) C-SYS 10

216 TUNING FREQUANCY (HIGHER PART) POS 84

217 TUNING FREQUANCY (LOWER PART)

218 S-SYS AFT (auto) C-SYS 10

219 TUNING FREQUANCY (HIGHER PART) POS 85

21A TUNING FREQUANCY (LOWER PART)

220 TUNING FREQUANCY (LOWER PART)

221 S-SYS AFT (auto) C-SYS 10

222 TUNING FREQUANCY (HIGHER PART) POS 88

223 TUNING FREQUANCY (LOWER PART)

21F TUNING FREQUANCY (HIGHER PART) POS 87

21B S-SYS AFT (auto) C-SYS 10

21C TUNING FREQUANCY (HIGHER PART) POS 86

21D TUNING FREQUANCY (LOWER PART)

21E S-SYS AFT (auto) C-SYS 10

224 S-SYS AFT (auto) C-SYS 10

225 TUNING FREQUANCY (HIGHER PART) POS 89

226 TUNING FREQUANCY (LOWER PART)

227 S-SYS AFT (auto) C-SYS 10

228 TUNING FREQUANCY (HIGHER PART) POS 90

229 TUNING FREQUANCY (LOWER PART)

22A S-SYS AFT (auto) C-SYS 10

22B TUNING FREQUANCY (HIGHER PART) POS 91

22C TUNING FREQUANCY (LOWER PART)

22D S-SYS AFT (auto) C-SYS 10

230 S-SYS AFT (auto) C-SYS 10

231 TUNING FREQUANCY (HIGHER PART) POS 93

232 TUNING FREQUANCY (LOWER PART)

233 S-SYS AFT (auto) C-SYS 10

234 TUNING FREQUANCY (HIGHER PART) POS 94

235 TUNING FREQUANCY (LOWER PART)

236 S-SYS AFT (auto) C-SYS 10

237 TUNING FREQUANCY (HIGHER PART) POS 95

22F TUNING FREQUANCY (LOWER PART)

22E TUNING FREQUANCY (HIGHER PART) POS 92

238 TUNING FREQUANCY (LOWER PART)

MODEL MODEL

239 S-SYS AFT (auto) C-SYS 10

23F S-SYS AFT (auto) C-SYS 10

23A TUNING FREQUANCY (HIGHER PART) POS 96

23B TUNING FREQUANCY (LOWER PART)

23C S-SYS AFT (auto) C-SYS 10

23D TUNING FREQUANCY (HIGHER PART) POS 97

23E TUNING FREQUANCY (LOWER PART)

LETTER NO. LETTER NO.

Page 17

REMARK

LAST INITIAL

SETTING DATA

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

C21-RF50S

DEFAULT RANGE

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

2C0

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

REMARK

LAST INITIAL

SETTING DATA

17-2

MODEL MODEL

2F0

2F1

2F2

2F3

2F4

2F5

2F6

2F7

2F8

2C1

2C2

2C3

2C4

2C5

2C6

2C7

2C8

2C9

2CA

2CB

2CC

2CD

2CE

2D0

2D1

2D2

2D3

2D4

2D5

2D6

2D7

2D8

2CF

2D9

2DA

2DB

2DC

2DD

2DE

2E0

2E1

2E2

2E3

2E4

2E5

2E6

2E7

2E8

2DF

2E9

2EA

2EF

2EB

2EE

2EC

2ED

2F9

2FA

2FB

2FE

2FF

2FC

2FD

LETTER NO. LETTER NO.

CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

WRITE(CPU)

DEFAULT RANGE

DATA MICON EEPROM EEPROM CHASSIS CTV FINAL

280

281

282

283

284

285

286

287

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

ADDRESS

288

01.C21-RF50S_E_p01-20 02.12.5, 12:4617

17-1

MODEL MODEL

289

28A

290

291

292

293

294

295

296

297

298

28F

28B

28C

28D

28E

299

29F

29A

29B

29C

29D

29E

2A0

2A1

2A2

2A3

2A4

2A5

2A6

2A7

2A8

2A9

2AA

2AF

2B0

2B1

2B2

2B3

2B4

2B5

2B6

2B7

2B8

2AB

2AE

2AC

2AD

2B9

2BF

2BA

2BB

2BE

2BC

2BD

LETTER NO. LETTER NO.

Page 18

C21-RF50S

Input 1, 3, 7 and 9 by R/C key.

Set vol up/down by R/C key.

HOTEL MODE ON

PASSWORD ****

NO RASTER

Blown out.

Replace the fuse.

Check IC701, D701 and

D707.

Abnormal

YES

ON/OFF ON

Abnormal

Normal

The fuse is blown out again.

Does horizontal circuit

oscillate ?

Check IC751 and IC801.

Which does D1001 (Power LED

Red) turns on or turns ON/OFF ?

Check T701 pin (7) voltage

(Approx. 310V at 220V AC)

Check F701.

Normal

Check Secondary Main+B

(Approx. 115V)

Normal

Abnormal

Normal

Check CRT connector

K1-K5 bias.

Check

IC801.

Check

C878.

Checking the

protector circuit.

Check R615 and R618.

Bus error mode.

(See Fig. below)

Does D1001 (Power LED

Green) turn on ?

Check IC702, IC753 and

D758.

Check R701, R707 and

D709.

YES

If a bus error happens, the LED RED indicator starts flashing and the power is turned off.

The power key is still effective.

EEPROM IC1003

(T24W08)

V/C/J IC801

(IX3410)

AV Switch IC401

(M52797SP)

Surround IC303

(AN5891K)

PLL Tuner TU201

(VTUCTF5511)

2s 0.5s

Trouble shooting table

18-2

UA1 HOTEL MODE APPLICATION NOTE

The purpose of this HOTEL MODE is to enable hotel authorized person to store the tuned

programs as hotel channels, current volume as hotel volume (maximum volume), picture and

sound setting. In addition, The user will not be able to select Preset and Channel-setting

functions.

How to enable/disable the "Hotel Mode" ?

Ans: a) Select the "Blueback" function (under "Menu-Feature" selection) by R/C, press the "-

/--" (one/two digit) key and keep pressing it for five second, then you can see the

hotel mode with four digits password.

hotel mode will be in enable condition, you can switch on/off the hotel mode by using

R/C (volume up/down) key.

b) Key in the four digits password starting with number "1", "3", "7" and "9", then the

channel for hotel mode.

#1 Ch 1 is your selected

Before set the hotel mode, it is better to choose ch 1 & set s-vol level Up to 75% full scale.

* We recommend

After set hotel mode, starting channel will be always ch 1 & maximum sound level out will

be set to 75% of full scale.

* If you set hotel mode in AV, starting channel will be the last ch which you received before

power off (same as normal operation)

When using hotel mode, the user can only control "Picture", "Sound" and "Feature" selec-

tion.

But it will return to the previous hotel mode setting condition after power off.

The user can't use:-- "Ch-setting" (OSD become violet) and "Preset".

The others function is allowed to be used.

CONDITION:

18-1

01.C21-RF50S_E_p01-20 02.12.5, 12:4618

Page 19

(Continued)

NO PICTURE, NO SOUND

Does noise signal appear at

pin (28) of IC801 ?

NO SOUND

No snow noise.

Does noise or signal appear at pin (40)

of IC801 ?

Noise increases but no signal is

received.

Check the tuner supply voltage LB must

be approx. 5V, BT must be approx. 33V

and CH preset data check.

Check the tuner AGC at

TP201.

Does signal

appear at pin (38)

of IC801 ?

Does signal appear

at pin (23) and (24)

of IC801 ?

Check IC801 and

its related circuit.

Check Q203,

Q204, IC401 and

it’s related circuit.

Check pin (27) of

IC801, Tuner and

related circuit.

Does the noise level increase at max.

Contrast, Brightness and Sound controls ?

CIRCUITS TO BE CHECKED:

» Tuner.

» PIF.

» Automatic Gain Control.

» (5V), (33V) Power Source.

CIRCUITS TO BE CHECKED:

» Sound system pins (28)

and (29) of IC801.

» Sound Detector Circuit.

» Sound Switch and Att.

Control.

» Audio Output Circuit.

Does signal appear at pins

(7) and (12) of IC301 ?

Check P301, P303, IC301

and their peripheral circuit.

AbnormalNormal

Normal

YES

(Signal)

YES

Check pin (38) of

IC801.

Check (37) of

IC801 and it’s

related circuit.

YES

Check SF201,

Tuner and their

related circuit.

Check IC801, C356, C359 and

their peripheral circuit.

Check IC303, IC401 and their

peripheral circuit.

NEITHER VERTICAL NOR

HORIZONTAL SYNCHRONIZATION

CIRCUIT TO BE CHECKED:

» Sync. Separator Circuit.

NO VERTICAL SCAN

Check R503, R506, R513,

C517 and D501.

DEFECTIVE VERTICAL AMP.

AND VERTICAL LINEARITY

Readjust vertical size.

(Bus Data)

Check pins (33) and (34) of

IC801.

Check IC501.Check C503 and C507.

Check IC501 bias.

Normal Abnormal

Vertical linearity and size

abnormal.

C21-RF50S

19-2

Trouble shooting table

(Continued)

19-1

01.C21-RF50S_E_p01-20 02.12.5, 12:4619

Trouble shooting table

Page 20

C21-RF50S

NO SPECIFIC COLOUR

Is some colour produced in

B/W broadcast reception ?

Is the white balance properly

adjusted ?

Readjust the white balance.

The picture colour is yellow.

The picture colour is magenta.

The picture colour is cyan.

Check Q870, Q885 and its

adjacent circuits.

Check Q871, Q883 and its

adjacent circuits.

Check Q872, Q887 and its

adjacent circuits.

Check IC801 and bias

control circuit.

Normal

NO SPECIFIC COLOUR

“PAL/SECAM”

(NO COLOUR SYNCHRONIZATION)

NO YES

YES

Check IC801, R801, R802,

R803, D804, D805, D806

and Q801.

Check X1001(12 MHz).

20-2

(Continued)

Trouble shooting table

01.C21-RF50S_E_p01-20 02.12.5, 12:4620

20-1

Page 21

654321

CHASSIS LAYOUT

C21-RF50S

02.C21RF50S_E_p21-35 02.12.5, 11:2921

Page 22

C21-RF50S

87109654321

BLOCK DIAGRAM-1

02.C21RF50S_E_p21-35 02.12.5, 11:2922

Page 23

C21-RF50S

1716 1918151413121110

02.C21RF50S_E_p21-35 02.12.5, 11:2923

Page 24

654321

C21-RF50S

BLOCK DIAGRAM-2

02.C21RF50S_E_p21-35 02.12.5, 11:2924

Page 25

WAVEFORMS

C21-RF50S

1.0Vp-p

66.0 Vp-p (H)

2.5 Vp-p (H)

72.0 Vp-p (H)

2.55 Vp-p (H)

3.0 Vp-p (V)

3.35Vp-p (H)

1.85 Vp-p (H)

68.0 Vp-p (H)

150.0 Vp-p (H)

8.4 Vp-p (H)

980 Vp-p (H)

1.3 Vp-p (V)

2.4 Vp-p (V)

0.98 Vp-p (V)

510 Vp-p (V)

43.0 Vp-p (V)

130.0 Vp-p (H)

02.C21RF50S_E_p21-35 02.12.5, 11:2925

Page 26

C21-RF50S

DESCRIPTION OF SCHEMATIC DIAGRAM

SAFETY NOTES:

1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACING PARTS.

2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING.

IMPORTANT SAFETY NOTICE:

PARTS MARKED WITH “å” ( ) ARE IMPORTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET.

SERVICE PRECAUTION:

THE AREA ENCLOSED BY THIS LINE ( CONNECTED WITH AC MAINS VOLTAGE. WHEN SERVICING THE AREA, CONNECT AN ISOLATING TRANSFORMER BETWEEN TV RECEIVER AND AC LINE TO ELIMINATE HAZARD OF ELECTRIC SHOCK.

NOTES:

1. The unit of resistance “ohm” is omitted. (K = 1000 ohms, M = Meg ohm).

2. All resistors are 1/10 watt, unless otherwise noted.

3. All capacitors are µF, unless therwise noted. (P = µµF).

) IS DIRECTLY

VOLTAGE MEASUREMENT CONDITIONS:

1. Voltage in parenthesis measured with no Signal.

2. Voltages without parenthesis measured with PAL Colour-Signal.

3. All the voltages in each point are measured with high impedence volt-meter.

WAVEFORM MEASUREMENT CONDITIONS:

1. Colour bar generator signal of 1.8V peak to peak applied at Base of Video Buffer Amp. Q200.

2. Approximately 4.0 V AGC bias.

02.C21RF50S_E_p21-35 02.12.5, 11:2926

Page 27

654321

SCHEMATIC DIAGRAM: CRT and HEADPHONE Unit

C21-RF50S

02.C21RF50S_E_p21-35 02.12.5, 11:2927

Page 28

C21-RF50S

87109654321

SCHEMATIC DIAGRAM: MAIN Unit

02.C21RF50S_E_p21-35 02.12.5, 11:2928

Page 29

C21-RF50S

1716 1918151413121110

02.C21RF50S_E_p21-35 02.12.5, 11:2929

Page 30

654321

C21-RF50S

PRINTED WIRING BOARD ASSEMBLIES

PWB-B:CRT Unit (Wiring Side)

PWB-B:CRT Unit (Component Side)

02.C21RF50S_E_p21-35 02.12.5, 11:2930

Page 31

654321

PWB-C:HEADPHONE Unit (Wiring Side )

C21-RF50S

PWB-C:HEADPHONE Unit (Component Side )

PWB-C:HEADPHONE Unit (Chip Parts Side)

02.C21RF50S_E_p21-35 02.12.5, 11:2931

Page 32

654321

C21-RF50S

PWB-A:MAIN Unit (Wiring Side)

02.C21RF50S_E_p21-35 02.12.5, 11:2932

Page 33

C21-RF50S

654321

PWB-A:MAIN Unit (Component Side)

02.C21RF50S_E_p21-35 02.12.5, 11:2933

Page 34

654321

C21-RF50S

PWB-A:MAIN Unit (Chip Parts Side)

02.C21RF50S_E_p21-35 02.12.5, 11:2934

Page 35

TOP VIEW

AT24W08

FX0008GE D601A

IX3410CE

64 33

132

2SC3198

2SC2482

DX0111PE

BASE COLLECTOR EMITTER

BCE

KA7808 KA7805

123

ANODE (RED) CATHODE (COMMON) ANODE (GREEN)

SE115N

STRF6654

AN5276

PX0037PE

2SD2586

112

+ ~ ~ -

COLLECTOR

BASE EMITTER

2SC2735 A1530AR

JC T·R

C3928AR

H·R

COLLECTOR

BASE EMITTER

TA48M033

135

TDA8357

114

M52797SP

28 15

112

AN5891K

24 13

SIDE VIEW

C21-RF50S

SOLID STATE DEVICE BASE DIAGRAM

02.C21RF50S_E_p21-35 02.12.5, 11:2935

Page 36

C21-RF50S

REPLACEMENT PART LIST

The following service parts list are available for purchase. Serviceman may quote the components shown in this page for servicing purposes.

PRODUCT SAFETY NOTE : Components marked with a å have special characteristics important to safety. The use of a substitute replacement part which does not have the same safety characteristics may create shock, fire or other hazards. Don’t degrade the safety of the receiver through improper servicing.

SYMBOL PART

No. No.

å ACC701 QACCB5003PEZZ AC Cord (For models with destination code 051 only).

å ACC701 QACCZ2008PEZZ AC Cord (For all models except destination code 051).

å C701 RC-FZ031SCEZZ 0.1 275V Metalized Plastic Film

å C721 RC-KZ0102GEZZ 680p 4KV Ceramic

å C759 VCKYPA1HB102K+ 1000p 50V Ceramic

DESCRIPTIONS

D701 RH-DX0111PEZZ DX0111PE

F301 QFS-J2521CEZZY Fuse (for C21-RM50, C21-RF50S, C21-RF50SN only)

å F701 QFS-C3229CEZZ Fuse

IC301 VHITDA7056A-1 IC TDA7056A (for C14-RM50, C14-RF50 only)

IC302 VHIAN5276//-1 IC AN5276 (for C21-RM50, C21-RF50S, C21-RF50SN only)

IC501 VHITDA8357/-1 TDA8357J/N1/S1

IC701 VHISTRF6653-1 IC STR-F6653 (for C14-RM50, C14-RF50 only)

IC701 VHISTRF6654-1 IC STR-F6654 (for C21-RM50, C21-RF50S, C21-RF50SN only)

å IC702 RH-FX0008GEZZ IC PC123FY8

IC801 RH-IX3368CEN6 I.C. (for C14-RM50, C14-RF50 only)

IC801 RH-IX3410CEN6 I.C. (for C21-RM50, C21-RF50S, C21-RF50SN only)

å L708 RCILG0095PEZZ Degaussing Coil (for C14-RM50, C14-RF50 only)

å L708 RCILG0069PEZZ Degaussing Coil (for C21-RM50, C21-RF50S, C21-RF50SN only)

Q602 VS2SD1877//1E TRS. 2SD1877 (for C14-RM50, C14-RF50 only)

Q602 VS2SD1586//1E TRS. 2SD2586 (for C21-RM50, C21-RF50S, C21-RF50SN only)

å R505 VRG-PD2HD330J 33 OHM 1/2W Fuse Re

å R712 VRG-PD2HD150J 15 OHM 1/2W Fuse Re

å R719 VRC-UA2HG825KY 8.2M OHM 1.2W SOLI

å R726 VRC-UA2HG825KY 8.2M OHM 1.2W SOLI

å S701 QSW-P0591CEZZ Power On/Off

å SC881 QSOCV0017PEZZ Socket (for C14-RM50, C14-RF50 only)

å SC882 QSOCV0016PEZZ CRT Socket (for C21-RM50, C21-RF50S, C21-RF50SN only)

å T601 RTRNZ0026PEZZ Transformer (for C21-RM50, C21-RF50S, C21-RF50SN only)

å T602 RTRNF0219PEZZ FBT (for C14-RM50, C14-RF50 only)

å T602 RTRNF0237PEZZ FBT (for C21-RM50, C21-RF50S, C21-RF50SN only)

å T603 RTRNZ0179CEZZ Transformer (for C14-RM50, C14-RF50 only)

å T701 RTRNZ0180PEZZ Transformer (for C14-RM50, C14-RF50 only)

å T701 RTRNZ0200PEZZ Transformer (for C21-RM50, C21-RF50S, C21-RF50SN only)

å TU201 VTUVTST5HD970 Tuner (for C14-RM50, C14-RF50 only)

å TU201 VTUCT5511+++ Tuner (for C21-RM50, C21-RF50S, C21-RF50SN only)

å VA700 RH-VX0073CEZZ Varistor

å RCILHA006WJZZ Deflection Yoke (for C14-RM50, C14-RF50 only)

å RCILH0193PEZZ Deflection Yoke (for C21-RM50, C21-RF50S, C21-RF50SN only)

RRMCGA066WJSA R/C (for C14-RM50, C14-RF50 only)

RRMCGA098WJSA Infrared R-C (for C21-RM50, C21-RF50S, C21-RF50SN only)

03.C21RF50S_E_p36-end 02.12.5, 12:5236

Page 37

Ref. No. Part No. Description Ref. No. Part No. Description

C21-RF50S

PARTS LIST

FOR REFERENCE ONLY

The components shown in page 37 - 44 serve as a reference. It is not meant for ordering of components for servicing purposes. Do not quote any componets from these lists.

Ref. No. Part No. Description

PICTURE TUBE

å VB51KQK99X/6E Picture Tube å RCiLG0069PEZZ Degaussing Coil å RCiLH0193PEZZ Deflection Yoke

QEARC2107PEZZ Grounding Strap LHLDW0003PEKZ ADG Coil Holder LHLDW1075PEKZ Holder MSPRT0001PEFJ CRT Spring PMAGF3046CEZZ Purity Magnet PSPAG0003PEZZ Spacer

PWB ASSEMBLIES

(NOT REPLACEMENT ITEM)

PWB-A DUNTK9988WEC6 MAIN Unit PWB-B DUNTK9990WEC7 CRT Unit PWB-C DUNTK9989WEV8 HEADPHONE Unit

PWB-A:DUNTK9988WEC6

MAIN UNIT

TUNER

NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN

ASSEMBLY NOT INDEPENDENTLY

å TU201 VTUCTF5511+++ Tuner

INTEGRATED CIRCUITS

IC302 VHiAN5276//-1 AN5276 IC303 VHiAN5891K+-1 AN5891K IC401 VHiM52797SP-1 M52797SP IC501 VHiTDA8357/-1 TDA8357J/N1/S1 IC605 VHiKA7808AP-1 KIA7808API IC701 VHiSTRF6654-1 STR-F6654

å IC702 RH-FX0008GEZZ PC123FY8

IC751 VHiTA48M033-1 TA48M033F IC753 VHiSE115N//-1 SE115N IC801 RH-iX3410CEN6 I.C. IC1003 VHiM24C08W/-1 M24C08-WBN6 IC1005 VHiKA7805AP-1 KIA7805API

TRANSISTORS

Q201 VS2SC2735//1EY 2SC2735 Q202 VS2SC3928AR-1Y 2SC3928AR Q203 VS2SC3928AR-1Y 2SC3928AR Q204 VS2SC3928AR-1Y 2SC3928AR Q303 VS2SC3928AR-1Y 2SC3928AR Q304 VS2SC3928AR-1Y 2SC3928AR Q305 VS2SC3928AR-1Y 2SC3928AR Q306 VS2SC3928AR-1Y 2SC3928AR Q510 VS2PD601AR/-1Y 2PD601AR Q601 VS2SC2482//-1+ 2SC2482 Q602 VS2SD2586//1E 2SD2586 Q603 VS2SC3928AR-1Y 2SC3928AR Q723 VS2SC3928AR-1Y 2SC3928AR Q752 VS2SC3198-G-1+ 2SC3198 Q753 VS2SC3198-G-1+ 2SC3198 Q801 VS2SA1530AR-1Y 2SA1530AR Q802 VS2SA1530AR-1Y 2SA1530AR Q1010 VS2SC3928AR-1Y 2SC3928AR

DIODES

D201 RH-EX0676GEZZY Zener Diode, 33V D202 VHD1SS119//-1Y Diode D301 VHD1SS119//-1Y Diode D302 RH-EX0615GEZZY Zener Diode, 5.6V D303 RH-EX0615GEZZY Zener Diode, 5.6V D304 RH-EX0631GEZZY Zener Diode, 9V D305 RH-EX0631GEZZY Zener Diode, 9V D307 RH-EX0631GEZZY Zener Diode, 9V D308 RH-EX0631GEZZY Zener Diode, 9V D309 RH-DX0445CEZZ Diode D312 VHD1SS119//-1Y Diode D401 RH-EX0631GEZZY Zener Diode, 9V D402 RH-EX0631GEZZY Zener Diode, 9V D501 RH-EX0640GEZZY Zener Diode, 12V D502 VHD1SS119//-1Y Diode D503 RH-DX0048GEZZY Diode D504 VHD1SS119//-1Y Diode D505 RH-DX0127CEZZY Diode D507 RH-DX0048GEZZY Diode D508 RH-EX0647GEZZY Zener Diode, 15V D509 RH-EX0647GEZZY Zener Diode D510 RH-EX0263TAZZY Zener Diode D511 RH-EX0263TAZZY Zener Diode D512 VHD1SS119//-1Y Diode D513 VHD1SS119//-1Y Diode D514 RH-EX0903CEZZY Zener Diode, 27V D515 RH-EX0903CEZZY Zener Diode, 27V D518 RH-DX0048GEZZY Diode D602 VHD1SS119//-1Y Diode D603 RH-DX0131CEZZY Diode D604 VHD1SS119//-1Y Diode D605 RH-EX0253TAZZY Zener Diode

03.C21RF50S_E_p36-end 02.12.5, 12:5237

Page 38

C21-RF50S

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

PWB-A:DUNTK9988WEC6

MAIN UNIT (Continued)

D606 VHD1SS119//-1Y Diode D607 RH-EX0660GEZZY Zener Diode, 22V D608 RH-EX0604GEZZY Zener Diode, 3.9V D609 VHD1SS119//-1Y Diode D610 RH-EX0662GEZZY Zener Diode, 23V D611 RH-DX0302CEZZY Diode D612 RH-EX0627GEZZY Zener Diode, 8.2V D613 VHD1SS119//-1Y Diode D614 VHD1SS119//-1Y Diode D701 RH-DX0111PEZZ Diode D702 VHD1SS82///1AY Diode D705 RH-DX0492CEZZY Diode D706 VHD1SS82///1AY Diode D707 VHD1SS82///1AY Diode D708 RH-DX0400CEZZY Diode D709 RH-DX0164CEZZY Diode D710 RH-EX0601GEZZY Zener Diode D711 VHD1SS82///1AY Diode D713 RH-EX0621GEZZY Zener Diode, 6.8V D717 RH-DX0471CEZZY Diode D750 VHD1SS119//-1Y Diode D752 VHD1SS119//-1Y Diode D753 RH-DX0471CEZZY Diode D758 RH-DX0461CEZZ Diode D760 VHD1SS119//-1Y Diode D763 VHD1SS119//-1Y Diode D801 VHD1SS119//-1Y Diode D802 VHD1SS119//-1Y Diode D803 VHD1SS119//-1Y Diode D804 VHD1SS119//-1Y Diode D805 VHD1SS119//-1Y Diode D806 VHD1SS119//-1Y Diode D810 RH-EX0610GEZZY Zener Diode, 4.7V D813 RH-DX0048GEZZY Diode D1001 RH-PX0037PEZZ Power Indicator D1002 RH-EX0253TAZZY Zener Diode D1003 RH-EX0253TAZZY Zener Diode D1007 RH-EX0263TAZZY Zener Diode D1008 RH-EX0263TAZZY Zener Diode D1009 RH-EX0263TAZZY Zener Diode D1010 RH-EX0263TAZZY Zener Diode

å VA700 RH-VX0073CEZZ Varistor

PACKAGED CIRCUITS

PR701 RMPTP0001PEZZ Packaged Circuit X1001 RCRSB0300CEZZ Crystal, 12MHz

FILTERS AND COILS

CF201 RFiLC0465CEZZ Ceramic Filter CF202 RFiLC0318CEZZ Ceramic Filter CF203 RFiLC0446CEZZ Ceramic Filter L203 VP-DF270K0000Y Peaking 27µH L204 VP-XFR82K0000Y Peaking 0.82µH L205 VP-DF1R0K0000Y Peaking 1µH L206 VP-DF1R0K0000Y Peaking 1µH L208 VP-XF100K0000Y Peaking 10µH L209 VP-XF6R8K0000Y Peaking 6.8µH L210 VP-XF120K0000Y Peaking 12µH L212 VP-DF270K0000Y Peaking 27µH L401 VP-DF1R0K0000Y Peaking 1µH L601 VP-CF1R0M0000Y Peaking 1µH L603 RCiLP0225CEZZ Coil

å L702 RCiLF0019PEZZ Coil

L802 VP-DF100K0000Y Peaking 10µH L803 VP-DF100K0000Y Peaking 10µH L1030 VP-DF100K0000Y Peaking 10µH L1050 VP-DF100K0000Y Peaking 10µH L1051 VP-DF100K0000Y Peaking 10µH SF201 RFiLC0037PEZZ SAW Filter

TRANSFORMERS

å T601 RTRNZ0026PEZZ Transformer

å T602 RTRNF0237PEZZ FBT å T701 RTRNZ0200PEZZ Transformer

CAPACITORS

[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]

C200 VCEA0A1CW476M+ 47 16V EL. C202 VCEA0A1CW477M+ 470 16V EL. C203 VCKYCY1HF103Z 0.01 50V Ceramic C204 VCEA0A1CW477M+ 470 16V EL. C205 VCKYCY1HF103Z 0.01 50V Ceramic C206 VCEA0A1HW106M+ 10 50V EL. C207 VCKYCY1HF103Z 0.01 50V Ceramic C208 VCKYCY1HF103Z 0.01 50V Ceramic C209 VCKYCY1HF103Z 0.01 50V Ceramic C210 VCKYCY1HF103Z 0.01 50V Ceramic C211 VCKYCY1EF104Z 0.1 25V Ceramic C212 VCEA0A1CW106M+ 10 16V EL. C213 VCKYCY1HF223Z 0.022 50V Ceramic C214 VCEA0A1CW226M+ 22 16V EL. C216 VCKYCY1HB821K 820p 50V Ceramic C217 VCKYCY1HB472K 4700p 50V Ceramic C220 VCKYCY1HF103ZY 0.01 50V Ceramic C306 VCEA0A1EW107M+ 100 25V EL. C307 VCEA0A1HW105M+ 1 50V EL. C308 VCEA0A1EW108M 1000 25V EL. C309 VCEA0A1HW225M+ 2.2 50V EL. C310 VCEA0A1CW106M+ 10 16V EL. C311 VCEA0A1EW108M 1000 25V EL. C312 VCQYTA1HM472J+ 4700p 50V Mylar C313 VCQYTA1HM472J+ 4700p 50V Mylar C314 VCEA0A1EW108M 1000 25V EL. C316 VCEA0A1HW224M+ 0.22 50V EL. C317 VCEA0A1HW224M+ 0.22 50V EL. C322 VCEA0A1CW106M+ 10 16V EL. C323 VCEA0A1CW106M+ 10 16V EL. C324 VCQYTA1HM153J+ 0.015 50V Mylar C326 VCQYTA1HM333J+ 0.033 50V Mylar C327 VCQYTA1HM103J+ 0.01 50V Mylar C328 VCEA0A1HW104M+ 0.1 50V EL. C329 VCEA0A1CW106M+ 10 16V EL. C330 VCEA0A1HW105M+ 1 50V EL. C331 VCEA0A1HW105M+ 1 50V EL. C332 VCEA0A1EW108M 1000 25V EL. C333 VCKYPA2HB102K+ 1000p 500V Ceramic C335 VCQYTA1HM333J+ 0.033 50V Mylar C336 VCQYTA1HM393J+ 0.039 50V Mylar C337 VCKYCY1HB103K 0.01 50V Ceramic C340 VCEA0A1CW106M+ 10 16V EL. C341 VCEA0A1CW106M+ 10 16V EL. C342 VCEA0A1CW106M+ 10 16V EL. C343 VCQYTA1HM103J+ 0.01 50V Mylar C344 VCEA0A1HW104M+ 0.1 50V EL. C345 VCFYFA1HA684J+ 0.68 50V Mylar C346 VCEA0A1CW106M+ 10 16V EL. C347 VCEA0A1CW106M+ 10 16V EL. C348 VCKYPA1HF103Z+ 0.01 50V Ceramic C349 VCEA0A1CW107M+ 100 16V EL. C350 VCEA0A1CW106M+ 10 16V EL. C352 VCEA0A1CW106M+ 10 16V EL. C355 VCEA0A1CW106M+ 10 16V EL. C356 VCKYCY1HB682K 6800p 50V Ceramic C357 VCKYCY1HB182K 1800p 50V Ceramic C358 VCEA9M1CW106M+ 10 16V EL. C359 VCEA9M1CW106M+ 10 16V EL. C361 VCEA0A1CW106M+ 10 16V EL. C362 VCEA0A1CW106M+ 10 16V EL. C363 VCEA0A1CW106M+ 10 16V EL. C364 VCEA0A1CW106M+ 10 16V EL. C365 VCKYCY1HB472K 4700p 50V Ceramic C366 VCKYCY1HB102K 1000p 50V Ceramic C367 VCKYCY1HB221K 220p 50V Ceramic C368 VCKYCY1HB221K 220p 50V Ceramic C370 VCEA0A1HW105M+ 1 50V EL. C371 VCEA0A1CW476M+ 47 16V EL. C372 VCEA0A1CW106M+ 10 16V EL. C375 VCEAEA1HW225M+ 2.2 50V EL.

03.C21RF50S_E_p36-end 02.12.5, 12:5238

Page 39

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

C21-RF50S

PWB-A:DUNTK9988WEC6

MAIN UNIT (Continued)

C376 VCEA0A1CW106M+ 10 16V EL. C390 VCEA0A1HW105M+ 1 50V EL. C401 VCKYPA1HF103Z+ 0.01 50V Ceramic C402 VCEA0A1CW106M+ 10 16V EL. C403 VCEA0A1CW106M+ 10 16V EL. C404 VCEA0A1CW106M+ 10 16V EL. C405 VCEA0A1CW107M+ 100 16V EL. C406 VCEA0A1CW477M+ 470 16V EL. C407 VCEA0A1CW106M+ 10 16V EL. C408 VCEA0A1CW106M+ 10 16V EL. C409 VCKYCY1CF474Z 0.47 16V Ceramic C410 VCKYCY1EF104Z 0.1 25V Ceramic C411 VCKYCY1HB102K 1000p 50V Ceramic C412 VCKYCY1HB472K 4700p 50V Ceramic C414 VCKYCY1HB472K 4700p 50V Ceramic C415 VCKYCY1HB102K 1000p 50V Ceramic C416 VCKYCY1HB472KY 4700p 50V Ceramic C469 VCEA0A1HW105M+ 1 50V EL. C501 VCKYCY1HF103Z 0.01 50V Ceramic C502 VCKYCY1HF103Z 0.01 50V Ceramic C503 VCEA0A1EW108M 1000 25V EL. C504 VCKYCY1HF223Z 0.022 50V Ceramic C506 VCQYTA1HM104J+ 0.1 50V Mylar C507 VCEA0A1JW107M 100 63V EL. C508 VCQYTA1HM103J+ 0.01 50V Mylar C512 VCKYCY1HB102K 1000p 50V Ceramic C513 VCKYCY1HB102K 1000p 50V Ceramic C514 VCKYPA1HF103Z+ 0.01 50V Ceramic C515 VCKYPA2HB102K+ 1000p 500V Ceramic C516 VCEA0A1JW477M 470 63V EL. C517 VCQYTA1HM104J+ 0.1 50V Mylar C520 VCKYCY1CB104KY 0.1 16V Ceramic C601 VCEA0A2EW106M 10 250V EL. C602 VCQYTA1HM104J+ 0.1 50V Mylar C603 VCEA0A1HW105M+ 1 50V EL. C604 VCEA0A1HW105M+ 1 50V EL. C605 VCKYPA1HF103Z+ 0.01 50V Ceramic C606 VCKYCY1HF103Z 0.01 50V Ceramic C607 VCEA0A1CW477M+ 470 16V EL. C608 VCEA0A1EW476M+ 47 25V EL. C609 VCEA0A1EW108M 1000 25V EL. C610 VCFYSB2EB823J 0.082 250V Mylar C611 VCKYPA2HB102K+ 1000p 500V Ceramic C612 RC-EZ0776CEZZ 100 160V EL. C613 VCFPFA2EB564J 0.56 250V M-Poly. C614 RC-KZ0037CEZZ 390p 2kV Ceramic C615 VCFPPB2EB224J 0.22 250V M-Poly. C616 VCFPFD3CA912H 9100p 1.6kV M-Poly. C617 VCKYPA2HB102K+ 1000p 500V Ceramic C620 VCKYCY1EF104Z 0.1 25V Ceramic C623 VCQYTA1HM222J+ 2200p 50V Mylar C624 VCQYTA1HM472J+ 4700p 50V Mylar C625 VCEA0A1HW105M+ 1 50V EL. C626 VCKYCY1HF223Z 0.022 50V Ceramic C627 VCEA0A1HW106M+ 10 50V EL. C628 VCEA0A1HW474M+ 0.47 50V EL. C650 VCKYCY1EF104Z 0.1 25V Ceramic C654 VCEA0A1CW476M+ 47 16V EL. C700 VCQYTA2AA104K+ 0.1 100V Mylar

å C701 RC-FZ031SCEZZ 0.1

C702 RC-KZ0029CEZZ+ 0.01 250V Ceramic C703 RC-KZ0029CEZZ+ 0.01 250V Ceramic C704 VCKYPA2HB102K+ 1000p 500V Ceramic C705 VCKYPA2HB102K+ 1000p 500V Ceramic C707 RC-EZA072WJZZ 220 400V EL. C708 RC-KZ0029CEZZ+ 0.01 250V Ceramic C709 VCQYTA1HM471J+ 470p 50V Mylar C711 RC-KZ0039CEZZ 680p 2kV Ceramic C712 VCQYTA1HM102J+ 1000p 50V Mylar C713 RC-KZ007JCEZZ 0.01 250V Ceramic C714 VCKYPH3DB561K 560p 2KV Ceramic C715 VCKYPA2HB102K+ 1000p 500V Ceramic

AC250V

Film

C716 VCEA0A1EW107M+ 100 25V EL. C717 VCQYTA1HM182J+ 1800p 50V Mylar C718 VCEAGA2AW475M+ 4.7 100V EL.

å C721 RC-KZ0102GEZZ 680p 4kV Ceramic

C752 VCEA0A0JW107M+ 100 6.3V EL. C753 VCKYPA2HB102K+ 1000p 500V Ceramic C754 VCEA0A1CW476M+ 47 16V EL. C755 VCEA0A1CW108M+ 1000 16V EL. C756 VCEA0A1CW108M+ 1000 16V EL. C757 VCE9GA1HW105M+ 1 50V EL. (N.P) C759 VCKYPA1HB102K+ 1000p 50V Ceramic C760 RC-KZ0039CEZZ 680p 2kV Ceramic C761 VCEA4W2CN227M 220 160V EL. C762 VCQYTA1HM473J+ 0.047 50V Mylar C802 VCEA0A1CW108M+ 1000 16V EL. C803 VCEA9M1CW107M+ 100 16V EL. C804 VCKYCY1HB222K 2200p 50V Ceramic C805 VCKYCY1HB102KY 1000p 50V Ceramic C806 VCKYCY1HB102KY 1000p 50V Ceramic C807 VCKYCY1HB102KY 1000p 50V Ceramic C808 VCEA0A1CW107M+ 100 16V EL. C809 VCKYCY1CF474Z 0.47 16V Ceramic C810 VCKYCY1CF474Z 0.47 16V Ceramic C811 VCEA0A1CW107M+ 100 16V EL. C812 VCFYFA1HA224J+ 0.22 50V Mylar C813 VCFYFA1HA224J+ 0.22 50V Mylar C814 VCKYCY1HB471K 470p 50V Ceramic C1001 VCEA0A0JW107M+ 100 6.3V EL. C1003 VCEA0A1CW106M+ 10 16V EL. C1004 VCKYCY1CF474Z 0.47 16V Ceramic C1005 VCKYCY1HF223Z 0.022 50V Ceramic C1006 VCEA0A1CW106M+ 10 16V EL. C1008 VCCCCY1HH330J 33p 50V Ceramic C1009 VCCCCY1HH330J 33p 50V Ceramic C1010 VCEA0A0JW107M+ 100 6.3V EL. C1011 VCKYCY1CF474Z 0.47 16V Ceramic C1012 VCKYCY1CF474Z 0.47 16V Ceramic C1013 VCEA0A0JW107M+ 100 6.3V EL. C1014 VCEA0A1CW106M+ 10 16V EL. C1016 VCQYTA1HM104J+ 0.1 50V Mylar C1018 VCKYCY1HB221K 220p 50V Ceramic C1019 VCEA9M1HW225M+ 2.2 50V EL. C1021 VCKYCY1CF474Z 0.47 16V Ceramic C1023 VCEA0A1CW107M+ 100 16V EL. C1024 VCEA0A1CW106M+ 10 16V EL.

RESISTORS

[M-Ox.··· Metal Oxide, M-Film··· Metal Film]

RJ2 VRN-MD2AL000J 0 1/10W M-Film RJ9 VRS-CY1JF000JY 0 1/16W M-Ox. RJ10 VRN-MD2AL000J 0 1/10W M-Film RJ12 VRN-MD2AL000J 0 1/10W M-Film RJ13 VRN-MD2AL000J 0 1/10W M-Film RJ15 VRN-MD2AL000J 0 1/10W M-Film RJ19 VRS-CY1JF000JY 0 1/16W M-Ox. RJ21 VRN-MD2AL000J 0 1/10W M-Film RJ22 VRN-MD2AL000J 0 1/10W M-Film RJ23 VRN-MD2AL000J 0 1/10W M-Film RJ26 VRN-MD2AL000J 0 1/10W M-Film RJ27 VRN-MD2AL000J 0 1/10W M-Film RJ30 VRN-MD2AL000J 0 1/10W M-Film RJ31 VRN-MD2AL000J 0 1/10W M-Film RJ32 VRN-MD2AL000J 0 1/10W M-Film RJ33 VRN-MD2AL000J 0 1/10W M-Film RJ34 VRN-MD2AL000J 0 1/10W M-Film RJ38 VRS-CY1JF000JY 0 1/16W M-Ox. RJ39 VRN-MD2AL000J 0 1/10W M-Film RJ41 VRN-MD2AL000J 0 1/10W M-Film RJ42 VRN-MD2AL000J 0 1/10W M-Film RJ43 VRN-MD2AL000J 0 1/10W M-Film RJ51 VRN-MD2AL000J 0 1/10W M-Film RJ53 VRN-MD2AL000J 0 1/10W M-Film RJ55 VRN-MD2AL000J 0 1/10W M-Film RJ56 VRN-MD2AL000J 0 1/10W M-Film RJ58 VRN-MD2AL000J 0 1/10W M-Film RJ61 VRN-MD2AL000J 0 1/10W M-Film

03.C21RF50S_E_p36-end 02.12.5, 12:5239

Page 40

C21-RF50S

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

PWB-A:DUNTK9988WEC6

MAIN UNIT (Continued)

RJ64 VRN-MD2AL000J 0 1/10W M-Film RJ66 VRS-CY1JF000JY 0 1/16W M-Ox. RJ67 VRN-MD2AL000J 0 1/10W M-Film RJ68 VRN-MD2AL000J 0 1/10W M-Film RJ69 VRN-MD2AL000J 0 1/10W M-Film RJ71 VRN-MD2AL000J 0 1/10W M-Film RJ74 VRN-MD2AL000J 0 1/10W M-Film RJ75 VRN-MD2AL000J 0 1/10W M-Film RJ79 VRN-MD2AL000J 0 1/10W M-Film RJ80 VRN-MD2AL000J 0 1/10W M-Film RJ81 VRN-MD2AL000J 0 1/10W M-Film RJ82 VRN-MD2AL000J 0 1/10W M-Film RJ84 VRS-CY1JF000JY 0 1/16W M-Ox. RJ85 VRS-CY1JF000JY 0 1/16W M-Ox. RJ87 VRN-MD2AL000J 0 1/10W M-Film RJ88 VRN-MD2AL000J 0 1/10W M-Film RJ89 VRN-MD2AL000J 0 1/10W M-Film RJ90 VRN-MD2AL000J 0 1/10W M-Film RJ92 VRN-MD2AL000J 0 1/10W M-Film RJ94 VRN-MD2AL000J 0 1/10W M-Film RJ95 VRN-MD2AL000J 0 1/10W M-Film RJ97 VRN-MD2AL000J 0 1/10W M-Film RJ99 VRN-MD2AL000J 0 1/10W M-Film RJ103 VRN-MD2AL000J 0 1/10W M-Film RJ105 VRN-MD2AL000J 0 1/10W M-Film RJ107 VRN-MD2AL000J 0 1/10W M-Film RJ205 VRN-MD2AL000J 0 1/10W M-Film RJ206 VRN-MD2AL000J 0 1/10W M-Film RJ208 VRN-MD2AL000J 0 1/10W M-Film RJ209 VRN-MD2AL000J 0 1/10W M-Film RJ210 VRN-MD2AL000J 0 1/10W M-Film RJ211 VRS-CY1JF000JY 0 1/16W M-Ox. RJ212 VRS-CY1JF000JY 0 1/16W M-Ox. RJ213 VRS-CY1JF000JY 0 1/16W M-Ox. RJ214 VRS-CY1JF000JY 0 1/16W M-Ox. RJ215 VRS-CY1JF000JY 0 1/16W M-Ox. R201 VRN-MD2AL101J 100 1/10W M-Film R202 VRN-MD2AL101J 100 1/10W M-Film R203 VRD-RM2HD102JY 1k 1/2W Carbon R204 VRD-RM2HD102JY 1k 1/2W Carbon R205 VRD-RA2BE680JY 68 1/8W Carbon R206 VRN-MD2AL122J 1.2k 1/10W M-Film R207 VRN-MD2AL221J 220 1/10W M-Film R208 VRN-MD2AL181J 180 1/10W M-Film R209 VRN-MD2AL392J 3.9k 1/10W M-Film R210 VRN-MD2AL392J 3.9k 1/10W M-Film R211 VRN-MD2AL682J 6.8k 1/10W M-Film R212 VRN-MD2AL222J 2.2k 1/10W M-Film R213 VRN-MD2AL473J 47k 1/10W M-Film R214 VRN-MD2AL473J 47k 1/10W M-Film R216 VRN-MD2AL681J 680 1/10W M-Film R217 VRD-RA2BE392JY 3.9k 1/8W Carbon R218 VRN-MD2AL102J 1k 1/10W M-Film R219 VRN-MD2AL391J 390 1/10W M-Film R220 VRN-MD2AL101J 100 1/10W M-Film R221 VRN-MD2AL102J 1k 1/10W M-Film R222 VRN-MD2AL681J 680 1/10W M-Film R223 VRD-RA2BE101JY 100 1/8W Carbon R224 VRN-MD2AL750J 75 1/10W M-Film R225 VRD-RA2EE680JY 68 1/4W Carbon R229 VRD-RA2BE820JY 82 1/8W Carbon R230 VRN-MD2AL102J 1k 1/10W M-Film R231 VRN-MD2AL102J 1k 1/10W M-Film R232 VRD-RA2BE680JY 68 1/8W Carbon R233 VRN-MD2AL181J 180 1/10W M-Film R234 VRN-MD2AL331J 330 1/10W M-Film R235 VRN-MD2AL561J 560 1/10W M-Film R236 VRN-MD2AL681J 680 1/10W M-Film R237 VRN-MD2AL272J 2.7k 1/10W M-Film R238 VRN-MD2AL821J 820 1/10W M-Film R239 VRN-MD2AL221J 220 1/10W M-Film R300 VRN-MD2AL680J 68 1/10W M-Film

R306 VRN-MD2AL123J 12k 1/10W M-Film R307 VRD-RA2BE562JY 5.6k 1/8W Carbon R308 VRD-RA2BE332JY 3.3k 1/8W Carbon R309 VRN-MD2AL562J 5.6k 1/10W M-Film R310 VRD-RA2BE103JY 10k 1/8W Carbon R311 VRN-MD2AL332J 3.3k 1/10W M-Film R312 VRD-RA2BE101JY 100 1/8W Carbon R313 VRD-RA2BE101JY 100 1/8W Carbon R314 VRN-MD2AL224J 220k 1/10W M-Film R315 VRN-MD2AL152J 1.5k 1/10W M-Film R316 VRN-MD2AL562J 5.6k 1/10W M-Film R318 VRN-MD2AL152J 1.5k 1/10W M-Film R319 VRD-RA2BE562JY 5.6k 1/8W Carbon R322 VRN-MD2AL101J 100 1/10W M-Film R323 VRN-MD2AL103J 10k 1/10W M-Film R324 VRN-MD2AL103J 10k 1/10W M-Film R325 VRN-MD2AL102J 1k 1/10W M-Film R326 VRN-MD2AL332J 3.3k 1/10W M-Film R327 VRN-MD2AL564J 560k 1/10W M-Film R328 VRN-MD2AL564J 560k 1/10W M-Film R329 VRN-MD2AL332J 3.3k 1/10W M-Film R332 VRN-MD2AL561J 560 1/10W M-Film R333 VRN-MD2AL103J 10k 1/10W M-Film R334 VRN-MD2AL102J 1k 1/10W M-Film R335 VRN-MD2AL561J 560 1/10W M-Film R336 VRN-MD2AL102J 1k 1/10W M-Film R337 VRN-MD2AL101J 100 1/10W M-Film R338 VRN-MD2AL103J 10k 1/10W M-Film R339 VRN-MD2AL564J 560k 1/10W M-Film R340 VRN-MD2AL332J 3.3k 1/10W M-Film R341 VRN-MD2AL332J 3.3k 1/10W M-Film R342 VRN-MD2AL564J 560k 1/10W M-Film R343 VRN-MD2AL104J 100k 1/10W M-Film R344 VRN-MD2AL101J 100 1/10W M-Film R345 VRN-MD2AL104J 100k 1/10W M-Film R356 VRN-MD2AL103J 10k 1/10W M-Film R358 VRN-MD2AL680J 68 1/10W M-Film R376 VRN-MD2AL101J 100 1/10W M-Film R377 VRN-MD2AL101J 100 1/10W M-Film R378 VRN-VV3DBR12J 0.12 2W M-Film R401 VRD-RA2BE103JY 10k 1/8W Carbon R403 VRN-MD2AL101J 100 1/10W M-Film R404 VRD-RA2BE820JY 82 1/8W Carbon R406 VRN-MD2AL103J 10k 1/10W M-Film R411 VRD-RA2BE820JY 82 1/8W Carbon R412 VRN-MD2AL101J 100 1/10W M-Film R501 VRN-MD2AL182J 1.8k 1/10W M-Film R502 VRN-MD2AL182J 1.8k 1/10W M-Film R503 VRD-RM2HD1R5JY 1.5 1/2W Carbon R505 VRG-PD2HD330J 33 1/2W Fuse Resistor R506 VRD-RA2BE224JY 220k 1/8W Carbon R508 VRD-RM2HD221JY 220 1/2W Carbon R509 VRD-RM2HD1R0JY 1 1/2W Carbon R510 VRN-MD2AL101J 100 1/10W M-Film R511 VRN-MD2AL101J 100 1/10W M-Film R513 VRD-RA2BE393JY 39k 1/8W Carbon R514 VRN-MD2AL101J 100 1/10W M-Film R515 VRN-MD2AL272J 2.7k 1/10W M-Film R516 VRD-RM2HD223J 22k 1/2W Carbon R520 VRS-CY1JF104JY 100k 1/16W M-Ox. R521 VRS-CY1JF392JY 3.9k 1/16W M-Ox. R602 VRN-VV3DBR82J 0.82 2W M-Film R603 VRD-RM2HD102JY 1k 1/2W Carbon R604 VRD-RA2BE393JY 39k 1/8W Carbon R605 VRD-RM2HD101JY 100 1/2W Carbon R606 VRD-RA2BE333JY 33k 1/8W Carbon R607 VRN-MD2AL102J 1k 1/10W M-Film R608 VRN-MD2AL123J 12k 1/10W M-Film R609 VRD-RA2BE153GY 15k 1/8W Carbon R610 VRD-RA2BE822JY 8.2k 1/8W Carbon R611 VRD-RA2EE563GY 56k 1/4W Carbon R612 VRD-RA2BE103JY 10k 1/8W Carbon R613 VRD-RA2BE103JY 10k 1/8W Carbon R614 VRN-MD2AL103J 10k 1/10W M-Film R615 VRS-KT3LB332J 3.3k 3W M-Ox. R616 VRN-MD2AL102J 1k 1/10W M-Film

03.C21RF50S_E_p36-end 02.12.5, 12:5240

Page 41

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

C21-RF50S

PWB-A:DUNTK9988WEC6

MAIN UNIT (Continued)

R617 VRD-RM2HD472JY 4.7k 1/2W Carbon R618 VRS-KA3HG3R3K 3.3 5W M-Ox. R619 VRD-RM2HD682JY 6.8k 1/2W Carbon R622 VRS-VV3DB331J 330 2W M-Ox. R623 VRS-VV3DB150J 15 2W M-Ox. R624 VRD-RA2BE101JY 100 1/8W Carbon R625 VRN-MD2AL563J 56k 1/10W M-Film R626 VRN-MD2AL472J 4.7k 1/10W M-Film R628 VRD-RM2HD470JY 47 1/2W Carbon R629 VRS-CY1JF683JY 68k 1/16W M-Ox. R630 VRN-MD2AL100J 10 1/10W M-Film R631 VRN-MD2AL391J 390 1/10W M-Film R632 VRN-MD2AL273J 27k 1/10W M-Film R633 VRN-MD2AL102J 1k 1/10W M-Film R635 VRN-MD2AL822J 8.2k 1/10W M-Film R636 VRS-CY1JF223JY 22k 1/16W M-Ox. R638 VRN-MD2AL103J 10k 1/10W M-Film R639 VRD-RA2BE101JY 100 1/8W Carbon R640 VRS-CY1JF563JY 56k 1/16W M-Ox. R701 VRW-KQ41C3R3K 3.3 15W Cement R703 VRS-KT3LB473J 47k 3W M-Ox. R705 VRD-RA2BE122JY 1.2k 1/8W Carbon R706 VRD-RM2HD152JY 1.5k 1/2W Carbon R707 VRS-KT3LB473J 47k 3W M-Ox. R708 VRD-RM2HD272JY 2.7k 1/2W Carbon R709 VRD-RA2BE681JY 680 1/8W Carbon R710 VRN-VV3ABR39J 0.39 1W M-Film R711 VRN-VV3ABR33J 0.33 1W M-Film

å R712 VRG-PD2HD150J 15 1/2W Fuse Resistor å R719 VRC-UA2HG825KY 8.2M 1/2W Solid

R721 VRD-RA2BE393JY 39k 1/8W Carbon R723 VRD-RA2BE684JY 680k 1/8W Carbon

å R726 VRC-UA2HG825KY 8.2M 1/2W Solid

R728 VRN-MD2AL272J 2.7k 1/10W M-Film R750 VRD-RM2HD180JY 18 1/2W Carbon R755 VRD-RA2BE222JY 2.2k 1/8W Carbon R756 VRN-MD2AL152J 1.5k 1/10W M-Film R758 VRD-RA2BE102JY 1k 1/8W Carbon R759 VRN-MD2AL102J 1k 1/10W M-Film R760 VRD-RA2BE471JY 470 1/8W Carbon R761 VRD-RA2BE221JY 220 1/8W Carbon R764 VRN-MD2AL272J 2.7k 1/10W M-Film R766 VRD-RM2HD680JY 68 1/2W Carbon R801 VRN-MD2AL101J 100 1/10W M-Film R802 VRN-MD2AL101J 100 1/10W M-Film R803 VRN-MD2AL101J 100 1/10W M-Film R804 VRN-MD2AL101J 100 1/10W M-Film R805 VRS-CY1JF822JY 8.2k 1/16W M-Ox. R806 VRS-CY1JF123JY 12k 1/16W M-Ox. R807 VRN-MD2AL103J 10k 1/10W M-Film R808 VRN-MD2AL221J 220 1/10W M-Film R809 VRD-RA2BE224JY 220k 1/8W Carbon R811 VRN-MD2AL563J 56k 1/10W M-Film R812 VRN-MD2AL101J 100 1/10W M-Film R813 VRN-MD2AL221J 220 1/10W M-Film R1001 VRD-RA2BE221JY 220 1/8W Carbon R1002 VRN-MD2AL331J 330 1/10W M-Film R1003 VRN-MD2AL471J 470 1/10W M-Film R1004 VRN-MD2AL821J 820 1/10W M-Film R1005 VRD-RA2BE181JY 180 1/8W Carbon R1011 VRN-MD2AL820J 82 1/10W M-Film R1012 VRN-MD2AL391J 390 1/10W M-Film R1013 VRN-MD2AL101J 100 1/10W M-Film R1014 VRD-RA2BE101JY 100 1/8W Carbon R1015 VRN-MD2AL332J 3.3k 1/10W M-Film R1016 VRD-RA2BE101JY 100 1/8W Carbon R1017 VRN-MD2AL332J 3.3k 1/10W M-Film R1019 VRN-MD2AL472J 4.7k 1/10W M-Film R1020 VRD-RA2BE101JY 100 1/8W Carbon R1021 VRN-MD2AL153J 15k 1/10W M-Film R1022 VRD-RA2BE101JY 100 1/8W Carbon R1023 VRN-MD2AL101J 100 1/10W M-Film

R1024 VRN-MD2AL122J 1.2k 1/10W M-Film R1025 VRN-MD2AL101J 100 1/10W M-Film R1026 VRN-MD2AL224J 220k 1/10W M-Film R1027 VRD-RA2BE101JY 100 1/8W Carbon R1028 VRD-RA2BE391JY 390 1/8W Carbon R1030 VRN-MD2AL102J 1k 1/10W M-Film R1031 VRD-RA2BE562JY 5.6k 1/8W Carbon R1032 VRN-MD2AL332J 3.3k 1/10W M-Film R1033 VRD-RA2BE102JY 1k 1/8W Carbon R1034 VRD-RA2BE101JY 100 1/8W Carbon R1035 VRN-MD2AL332J 3.3k 1/10W M-Film R1036 VRN-MD2AL332J 3.3k 1/10W M-Film R1037 VRD-RA2BE101JY 100 1/8W Carbon R1038 VRD-RA2BE101JY 100 1/8W Carbon R1040 VRN-MD2AL101J 100 1/10W M-Film R1041 VRN-MD2AL101J 100 1/10W M-Film R1045 VRD-RA2BE271JY 270 1/8W Carbon R1046 VRD-RA2BE101JY 100 1/8W Carbon R1047 VRN-MD2AL101J 100 1/10W M-Film R1067 VRN-MD2AL101J 100 1/10W M-Film

SWITCHES

å S701 QSW-P0591CEZZ Main Power

S1001 QSW-K0003AJZZ+ CH-UP S1002 QSW-K0003AJZZ+ CH-DOWN S1003 QSW-K0003AJZZ+ VOL-UP S1004 QSW-K0003AJZZ+ VOL-DOWN S1005 QSW-K0003AJZZ+ Picture/Preset

MISCELLANEOUS PARTS

F301 QFS-J2521CEZZY Fuse, IC Protector

å F701 QFS-C3229CEZZ Fuse, T3.15A/250V

FH701 QFSHD1014CEZZ+ Fuse Holder FH702 QFSHD1013CEZZ+ Fuse Holder FB305 RBLN-0091GEZZY Ferrite Bead FB306 RBLN-0091GEZZY Ferrite Bead FB501 RBLN-0091GEZZY Ferrite Bead FB502 RBLN-0091GEZZY Ferrite Bead FB602 RBLN-0091GEZZY Ferrite Bead FB701 RBLN-0091GEZZY Ferrite Bead FB702 RBLN-0091GEZZY Ferrite Bead FB751 RBLN-0091GEZZY Ferrite Bead FB752 RBLN-0091GEZZY Ferrite Bead J20 QCNW-2553PEZZ Connecting Cord J21 QCNW-2554PEZZ Connecting Cord J402 QJAKE0211CE04 Jack J403 QJAKE0211CE09 Jack J404 QJAKE0210CE02 Jack J405 QTANJ0644CEZZ Rear AV Terminal P301 QPLGN0441CEZZ Plug 4-pin(S) P303 QPLGN0741CEZZ Plug 7-pin(HP) P502 QPLGN0660CEZZ Plug 6-pin(F) P602 QPLGN0641CEZZ Plug 6-pin(H) P701 QPLGN0260CEZZ Plug 2-pin(G) P712 QPLGN0269GEZZ Plug 2-pin(A) P1001 QPLGN0541CEZZ Plug 5-pin(K) P1002 QPLGN0541CEZZ Plug 5-pin(BC) RMC1001 RDA301PRDAR0321PEFW Heat Sink, for IC302 RDA302PRDAR0160PEFW Heat Sink, for D309 RDA501PRDAR0298PEFW Heat Sink, for IC501 RDA701PRDAR0260PEFW Heat Sink, for IC701 RDA754PRDAR0224PEFW Heat Sink, for Q602

RRMCU0222CEZZ R/C Receiver

LHLDP1066PE00 Holder LX-BZ0086TAFD Screw LX-BZ3049GEFD Screw LX-BZ3100CEFD Screw LX-TZ3004CEFD Screw

03.C21RF50S_E_p36-end 02.12.5, 12:5241

Page 42

C21-RF50S

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

PWB-B:DUNTK9990WEC7

CRT UNIT

TRANSISTORS

Q870 RH-TX0110BMZZ+ TX0110BM Q871 RH-TX0110BMZZ+ TX0110BM Q872 RH-TX0110BMZZ+ TX0110BM Q883 RH-TX0124BMZZ+ TX0124BM Q885 RH-TX0124BMZZ+ TX0124BM Q887 RH-TX0124BMZZ+ TX0124BM

DIODES

D811 VHD1SS119//-1Y Diode D812 VHD1SS119//-1Y Diode D880 VHD1SS119//-1Y Diode D881 VHD1SS119//-1Y Diode D882 VHD1SS119//-1Y Diode D883 VHD1SS244//-1Y Diode D884 VHD1SS244//-1Y Diode D885 VHD1SS244//-1Y Diode D886 VHD1SS244//-1Y Diode D887 VHD1SS244//-1Y Diode D888 VHD1SS244//-1Y Diode D890 RH-EX0627GEZZY Zener Diode, 8.2V

CAPACITORS

[EL.··· Electrolytic]

C871 VCKYPA1HB471K+ 470p 50V Ceramic C872 VCKYPA1HB471K+ 470p 50V Ceramic C873 VCKYPA1HB471K+ 470p 50V Ceramic C875 VCKYPA2HB102K+ 1000p 500V Ceramic C876 RC-KZ0150CEZZ 1000p 3kV Ceramic C878 VCEAGA2EW336M 33 250V EL. C880 VCKYPA1HB471K+ 470p 50V Ceramic C881 VCKYPA1HB471K+ 470p 50V Ceramic C882 VCKYPA1HB471K+ 470p 50V Ceramic

PWB-C:DUNTK9989WEV8

HEADPHONE UNIT

RESISTORS

[M-Film··· Metal Film]

RJ8 VRN-MD2AL000J 0 1/10W M-Film R354 VRN-MD2AL471J 470 1/10W M-Film R355 VRN-MD2AL471J 470 1/10W M-Film

MISCELLANEOUS PARTS

J351 QJAKJ0101SEZZ Jack, Headphone P351 QPLGN0441CEZZ Plug 4-pin P352 QPLGN0341CEZZ Plug 3-pin

RESISTORS

R879 VRD-RA2BE471JY 470 1/8W Carbon R880 VRD-RA2BE471JY 470 1/8W Carbon R881 VRD-RA2BE471JY 470 1/8W Carbon R882 VRS-VV3DB153J 15k 2W M-Ox. R883 VRD-RM2HD272JY 2.7k 1/2W Carbon R884 VRS-VV3DB153J 15k 2W M-Ox. R885 VRD-RM2HD272JY 2.7k 1/2W Carbon R886 VRS-VV3DB153J 15k 2W M-Ox. R887 VRD-RM2HD272JY 2.7k 1/2W Carbon R892 VRD-RA2BE102JY 1k 1/8W Carbon R893 VRD-RA2BE102JY 1k 1/8W Carbon R894 VRD-RA2BE102JY 1k 1/8W Carbon R895 VRD-RA2BE471JY 470 1/8W Carbon R896 VRD-RA2BE471JY 470 1/8W Carbon R899 VRD-RA2BE471JY 470 1/8W Carbon

[M-Ox.··· Metal Oxide]

MISCELLANEOUS PARTS

P851 QPLGN0641CEZZ Plug 6-pin(H) P882 QPLGN0541CEZZ Plug 5-pin(K)

å SC882 QSOCV0016PEZZ CRT Socket

03.C21RF50S_E_p36-end 02.12.5, 12:5242

Page 43

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

C21-RF50S

MISCELLANEOUS PARTS

å ACC701 QACCZ2008PEZZ AC Cord

LHLDK0005PE00 Holder LHLDZ0133PEZZ Holder QCNW-2405PEZZ Connecting Cord QCNW-2433PEN1 Connecting Cord QCNW-2463PEZZ Connecting Cord QCNW-2465PEZZ Connecting Cord LHLDW1003PEZZ Holder LHLDW1033PEZZ Holder LHLDW1033PEZZ Holder LHLDW1047PEZZ Holder LHLDW1060PEZZ Holder LHLDW1074PEKZ Holder LX-TZA003WJFD Screw LX-TZ3004CEFD Screw LX-TZ3011CEFD Screw LX-WZ0015PEFD Washer LX-WZ3050CEFD Washer XTASD40P20000 Screw PSPAN0005PEKZ Spacer

SUPPLIED ACCESSORIES

RRMCGA098WJSA Infrared R/C Unit TiNS-A256WJZZ Operation Manual

PACKING PARTS

(NOT REPLACEMENT ITEM)

SPAKCA197WJZZ Packing Case SPAKX2756PEZZ Buffer Material SSAKA0031PEZZ Polyethylene Bag SSAKH0016PEZZ Polyethylene Bag TLABK0002PEZZ No. Label TLABN0001PEZZ Serial No. Label

03.C21RF50S_E_p36-end 02.12.5, 12:5243

Page 44

C21-RF50S

1-3

1-2

1-6

1-8

1-7

1-9

1-4

1-5

1 1-1

2 2-1 2-2

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

CABINET PARTS

1 CCABAA104WEV0 Front Cabinet Assy(081/191) 1 CCABAA104WEV1 Front Cabinet Assy(191B) 1-1 1-2 HBDGEA003WJSA "HITACHI" Badge 1-3 JBTN-0347PESC Button, Power(081/191) 1-3 JBTN-0347PESD Button, Power(191B) 1-4 MSPRC0016PEFW Spring for Power Button 1-5 JBTN-0345PESC Button, Control(081/191) 1-5 JBTN-0345PESD Button, Control(191B) 1-6 HDECQ0186PESA R/C, LED Cover 1-7 HDECQA104WJSA Speaker Net(R)(081/191) 1-7 HDECQA104WJSB Speaker Net(R)(191B) 1-8 HDECQA105WJSA Speaker Net(L)(081/191) 1-8 HDECQA105WJSB Speaker Net(L)(191B) 1-9 VSP1206WB486A Speaker, x2 2 CCABBA091WEV0 Rear Cabinet Assy(081/191) 2 CCABBA091WEV1 Rear Cabinet Assy(191B) 2-1 2-2 TLABMA150WJZZ Model Label(081/191) 2-2 TLABMA180WJZZ Model Label(191B)

Not Available

Front Cabinet

Rear Cabinet

CABINET PARTS LOCATION

03.C21RF50S_E_p36-end 02.12.5, 12:5244

Page 45

C21-RF50S

03.C21RF50S_E_p36-end 02.12.5, 12:5245