Hitachi C14RM50(R) Service Manual

C14-RM50

UA1 Chassis

PAL/SECAM/NTSC

SERVICE MANUAL

YS

No.

C14-RM50

Destination Code

RUSSIA 431

CAUTION: Before servicing this chassis, it is important that the service technician read the

"IMPORTANT SERVICE NOTES" in this Service Manual.

CONTENTS

Page

» SPECIFICATIONS .............................................. 2

» IMPORTANT SERVICE NOTES ......................... 2

» ADJUSTMENT PRECAUTIONS .........................3

» TROUBLE SHOOTING TABLE ......................... 15

» CHASSIS LAYOUT ........................................... 18

» BLOCK DIAGRAM ............................................19

» DESCRIPTION OF SCHEMATIC DIAGRAM ....22

» SCHEMATIC DIAGRAMS

Ë CRT UNIT......................................................23

Ë HEADPHONE UNIT ...................................... 23

Ë MAIN UNIT ................................................... 24

» PRINTED WIRING BOARD ASSEMBLIES ...... 26

» SOLID STATE DEVICE BASE DIAGRAM ........ 31

» REPLACEMENT PARTS LIST ......................... 32

Ë ELECTRICAL PARTS

MAIN UNIT ................................................... 32

CRT UNIT ......................................................36

HEADPHONE UNIT ...................................... 37

Ë SUPPLIED ACCESSORIES......................... 37

Ë PACKING PARTS ..........................................37

Ë CABINET PARTS .......................................... 37

Page

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

SEPTEMBER 2002 Digital Media System Group, Hitachi Asia Ltd.

01.C14-RM50(R)_E/p01-17 02.12.5, 14:181

COLOR TELEVISION

C14-RM50

2-2

qualified service personnel only.

IMPORTANT SERVICE NOTES

Maintenance and repair of this receiver should be done by

SERVICING OF HIGH VOLTAGE SYSTEM AND

PICTURE TUBE

When servicing the high voltage system, remove static charge from it by

Connecting a 10K ohm Resistor in series with an insulated wire(such as a

test probe) between picture tube dag and 2nd anode lead. (AC line cord

should be disconnected from AC outlet.)

1. Picture tube in this receiver employs integral implosion protection.

discharging the high voltage completely.

2. Replace with tube of the same type number for continued safety.

3. Do not lift picture tube by the neck.

4. Handle the picture tube only when wearing shatterproof goggles and after

X-RAY

This receiver is designed so that any X-Ray radiation is kept to an absolute

minimum. Since certain malfunctions or servicing may produce potentially

than 23.5kV(at beam 0 µA) for the set.

22.0kV±1.5kV(at beam 800 µA) in the case of the set. The set has been factory -

1. When repairing the circuit, be sure not to increase the high voltage to more

hazardous radiation with prolonged exposure at close range, the following

SECAM-B/G/DK/K1

2. To keep the set in a normal opeartion , be sure to make it function on

precautions should be observed:

NTSC3.58/4.43MHz (AV)

repairing, never forget to check for such high voltage after the work.

* If there is a possibility that the high voltage fluctuates as a result of the

Adjusted to the above-mentioned high voltage.

C1(49.75MHz) thru C12(216.25 MHz)

S1(105.25MHz) thru S36(423.25HMz)

which may cause excess X-ray radiation.

3. Do not substitute a picture tube with unauthorizerd types and/or brands

C13(471.25MHz) thru C57(863.25MHz)

BEFORE RETURNING THE RECEIVER

Before returning the receiver to the user, perform the following safety Checks.

1. Inspect all lead dress to make certain that leads are not pinched or that

Depth:365.0mm

Height:333.0mm

Weight(approx):9.5kg

S37(431.25MHz) thru S41(463.25MHz)

fishpapers, cabinet backs, adjustment and compartment covers or shields, iso-

hardware is not lodged between the chassis and other metal parts in the

lation resistor- capacity networks, mechanical insulators etc.

receiver.

2. Inspect all protective devices such as non-metallic control knobs, insulating

2-1

SPECIFICATIONS

6.5MHz ............................................................................................................. 32.4MHz

6.0MHz ............................................................................................................. 32.9MHz

Sound IF Carrier Frequency

5.5MHz ............................................................................................................. 33.4MHz

Convergence .............................................................................. Self Convergence System

Focus .................................................................................... Quadra-Potential Electrostatic

01.C14-RM50(R)_E/p01-17 02.12.5, 14:182

Picture IF Carrier ................................................................................................ 38.9MHz

Sweep Deflection ................................................................................................... Magnetic

Intermediate Frequencies

Colour Sub-Carrier Frequency .........................................................................34.47MHz

Power Input ................................................................................... 110 ~ 240V AC 50/60 Hz

Power Consumption ...................................................................................................... 68W

Size ......................................................................................................... 5 × 9 cm (2 pcs)

Audio Power Output Rating ........................................................................... 5.0W(at Max.)

Voice Coil Impedance ........................................................................ 16 ohms at 400 Hz

Speaker

VHF/UHF ......................................................................................75 ohms Unbalanced

Aerial Input Impedance

Receiving System ........................................................................................... PAL-B/G/DK/I

VHF-Channels .................................................... E2(48.25MHz) thru E12(224.25MHz)

Tuner Ranges

2

UHF-Channels ................................................ E21(471.25MHz) thru E69(855.25MHz)

Dimensions ..................................................................................................Width:446.0mm

Specifications are subject to change without prior notice.

Cabinet material ................................................................................................. All Plastics

C14-RM50

AGC &

GEOMETRIC

MODE

↓

AGC TAKE OVER POINT (AGC)

↓

VERTICAL SLOPE (V-LIN)

↓

VERTICAL AMP (V-AMP)

↓

VERTICAL SHIFT (V-CENT)

↓

HORIZONTAL SHIFT (H-CENT)

↓

EAST-WEST WIDTH (H-SIZE)

↓

HORIZONTAL PARALLELOGRAM (EW//)

↓

EAST-WEST PARABOLA/WIDTH (PARA)

↓

EAST-WEST UPPER CORNER PARABOLA (COR (U))

↓

EAST-WEST LOWER CORNER PARABOLA (COR (L))

↓

EAST-WEST TRAPEZIUM (TRAPE)

↓

HORIZONTAL BOW (HB)

↓

S-CORRECTION (S-COR)

WHITE POINT

ADJ.

MODE

↓

W,P RED STD. W.T. (DRI-RS)

↓

W.P. GREEN STD. W.T.(DRI-GS)

↓

W.P.BLUE STD. W.T. (DRI-BS)

↓

W.P. RED COOL W.T.(DRI-RC)

↓

W.P. GREEN COOL W.T.(DRI-GC)

↓

W.P. BLUE COOL W.T. (DRI-BC)

↓

W.P. RED WARM W.T.(DRI-RW)

↓

W.P. GREEN WARM W.T.(DRI-GW)

↓

W.P. BLUE WARM W.T.(DRI-BW)

SUB

ADJ.

MODE

↓

MAX VOLUME (SUB-VOL)

↓

SUB CONTRAST (SUB-CON)

↓

SUB COLOUR (SUB-COL)

↓

SUB BRIGHTNESS (SUB-BRI)

↓

SUB TINT (SUB-TINT)

↓

SUB SHARPNESS (SUB-SHP)

↓

MAX HOTEL VOLUME (HTL-VOL)

↓

HOTEL PROGRAM NO(HTL-PRG)

↓

OSD GRB REFERENCE (RGB)

↓

BLACK LEVEL OFFSET R(CUT-R)

↓

BLACK LEVEL OFFSET B(CUT-B)

↓

CATHODE DRIVE LEVEL(CDL)

FORWARD : CH DOWN KEY

REVERSE : CH UP KEY

* ( ) means OSD display.

FORWARD : CH DOWN KEY

REVERSE : CH UP KEY

AGC &

GEOMETRIC

MODE

WHITE POINT

ADJ.

MODE

SUB

ADJ.

MODE

Y-DELAY

ADJ.

MODE

MISC.

OPTION

MODE

IC

OPTION

MODE

OFFSET

ADJ.

MODE

3-2

SERVICE MODE

Ë

(1) In the Service Mode, Key is used to select the mode in the following order.

C bus control

2

C bus control include

2

C bus control). (Use

2

3-1

ADJUSTMENT PRECAUTIONS

01.C14-RM50(R)_E/p01-17 02.12.5, 14:183

This model's setting are adjusted in two different ways: through the I

and in the conventional analog manner. The adjustments via the I

preset-only items and variable data.

CAUTION:MAKE SURE TV SET IS IN ’NORMAL CONDITION’ BERORE SWITCH TO

SERVICE MODE FOR ADJUSTMENT.

and the microprocessor is in input mode. (Adjustment through the I

JWS Key to set as well).

one by one.

1 Short JA 122 & JA 124 for 1 second and release to switch to the service mode position,

2 Press the CH DOWN / UP key on the remote controller to get ready to select the mode

1. Setting the service mode by the microprocessor.

one by one.

position, and the microprocessor is in out of the service mode.

3 Press the CH DOWN / UP key on the remote controller to select the modes reversibly

4 Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.

5 Short JA 122 & JA 124 for 1 second and release to switch to the normal mode (OFF)

2. Factory Presetting.

Service mode position. Initial values are automatically preset, only when a new EEPROM

is used (Judge with the first 4 bytes ).

1 Short JA 122 & JA 124 then turn “ON” the main power and release to switch to the

2 The initial data are preset as listed in page 8, 9, & 10.

FIRST TIME, make sure to short JA122 & JA124 to switch to the service mode

position first and then turn on the main power switch (See 2-1 above).

Precaution: If haven't done this initiation, it may possibly generate excessive Beam

current.

3 Make sure the data need modify or not (Initial data).

Note: Once the chassis has been assembly together and ready to be POWER ON for the

(UA1 Series type RH-IX3368CE Attachment)

3. For reference please check with memory map

3

C14-RM50

Y-DELAY

ADJ.

MODE

↓

Y-D TIME FOR PAL (TV) (DL-PT)

↓

Y-D TIME FOR SECAM (TV) (DL-ST)

↓

Y-D TIME FOR N358 (TV) (DL-3T)

↓

Y-D TIME FOR N443 (TV) (DL-4T)

↓

Y-D TIME FOR B/W (TV) (DL-TV)

↓

Y-D TIME FOR PAL (AV) (DL-PA)

↓

Y-D TIME FOR SECAM (AV) (DL-SA)

↓

Y-D TIME FOR N358 (AV) (DL-3A)

↓

Y-D TIME FOR N443(AV) (DL-4A)

↓

Y-D TIME FOR B/W (AV) (DL-AV)

*(Y-D : Y-DELAY)

OFFSET

ADJ.

MODE

↓

COLOUR OFFSET (PAL) (COL-OP)

↓

COLOUR OFFSET (SECAM) (COL-OS)

↓

COLOUR OFFSET (NTSC358) (COL-O3)

↓

COLOUR OFFSET (NTSC443) (COL-O4)

↓

SHARPNESS OFFSET (PAL) (SHP-OP)

↓

SHARPNESS OFFSET (SECAM) (SHP-OS)

↓

SHARPNESS OFFSET (NTSC358) (COL-O3)

↓

SHARPNESS OFFSET (NTSC443) (COL-O4)

IC

OPTION

MODE

↓

VERTICAL SCAN DISABLE(VSD)

↓

BLACK STRETCH (BKS)

↓

AUTO VOLUME LEVELING(AVL)

↓

FAST FILTER IF-PLL(FFI)

↓

ENABLE VERTICAL GUARD (EVG)

↓

EHT TRACKING MODE (EHT)

↓

OVERSCAN SWITCH OFF(OSO)

↓

AUTO COLOUR LIMIT(ACL)

↓

FORCED COLOUR LIMIT(FCO)

MISC.

OPTION

MODE

↓

SOUND SYSTEM M (S-M)

↓

SOUND SYSTEM DK (S-DK)

↓

SOUND SYSTEM I (S-I)

↓

SOUND SYSTEM BG (S-BG)

↓

PLAYBACK SECAM (P-SECAM)

↓

FE (RF) NTSC 3.58 (F-N358)

↓

FE (RF) NTSC 4.43 (F-N443)

↓

FE (RF) SECAM (F-SECAM)

↓

VIDEO MUTE AT IDENT LOSS (VMI)

↓

VIDEO MUTE AT PROGRAM

/SOURCE CHANGE (VMC)

↓

HOTEL MODE (HTL)

↓

REDUCED FM DEMODULATION

GAIN FOR BTSC SIGNAL (BTSC)

↓

A

A

↓

NUMBER OF EXT AV SOURCE (AV)

↓

FM WINDOW SELECTION (FMWS)

↓

SOUND MUTE BIT 0 (SM0)

↓

SOUND MUTE BIT 1 (SM1)

↓

THAI LANGUAGE (THA)

↓

ARABIC LANGUAGE (ARA)

↓

MALAY LANGUAGE (MAL)

↓

CHINESE LANGUAGE (CHI)

↓

FRENCH LANGUAGE (FRE)

↓

RUSSIAN LANGUAGE (RUS)

↓

FORCED V-SYNC SLICING LEVEL(FSL)

↓

SYNC OF OSD (HP2)

↓

CHARGE PUMP TUNER (CPT)

↓

B

B

↓

BILINGUAL(BIL)

↓

IF AGC SPEED BIT 0 (AGC0)

↓

IF AGC SPEED BIT 1 (AGC1)

↓

FOA Time Constant-RF (FOA-FE)

↓

FOB Time Constant-RF (FOB-FE)

↓

FOA Time Constant-AV (FOA-AV)

↓

FOB Time Constant-AV (FOB-AV)

↓

LED BLINK SPEED(LED-F)

↓

PWM VDLUME TABLE (MSA)

↓

OUTPUT VERHCAL GUARD (NDF)

4-2

FUNCTION AGC

RC COMMAND SERVICE-ITEM

* Direct Key-in for service item in service mode

CONTRAST DOWN V-LIN

COLOUR DOWN V-AMP

TINT DOWN H-CENT

BRIGHTNESS DOWN V-CENT

SYSTEM HB

SHARPNESS DOWN EW / /

TIMER SUB-VOL

BLUEBACK S-COR

COLOUR UP SUB-COL

CONTRAST UP SUB-CON

BRIGHTNESS UP SUB-BRI

TINT UP SUB TINT

SHARPNESS UP SUB-SHP

4-1

01.C14-RM50(R)_E/p01-17 02.12.5, 14:184

4

REMARK

INITIAL DATA FIX/ADJ

0 FIX

1 FIX

1 FIX

0 FIX

1 FIX

1 FIX

0 FIX

0 FIX

0 FIX

0 FIX

1 FIX

1 FIX

1 FIX

1 FIX

0 FIX

1 FIX

1 FIX

1 FIX

1 FIX

0 FIX

0 FIX

0 FIX

1 FIX

0 FIX

0 FIX

1 FIX

1 FIX

1 FIX

1 FIX

1 FIX

0 FIX

0 FIX

0 FIX

0 FIX

1 FIX

0 FIX

0 FIX

0 FIX

1 FIX

1 FIX

0 FIX

0 FIX

C14-RM50

0 ( 1 ) FIX

EEPROM ITEMS OSD DATA LENGTH

COLOUR OFFSET (NTSC358) COL-O3 0~15 4 CHG *1

COLOUR OFFSET (NTSC443) COL-O4 0~15 4 CHG *1

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

SHARPNESS OFFSET (PAL) SHP-OP 0~15 8 FIX

SHARPNESS OFFSET (SECAM) SHP-OS 0~15 8 FIX

SHARPNESS OFFSET (NTSC358) SHP-O3 0~15 12 FIX

SHARPNESS OFFSET (NTSC443) SHP-O4 0~15 8 FIX

VERTICAL SCAN DISABLE VSD

BLACK STRETCH BKS

REMARK

INITIAL DATA FIX/ADJ

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

AUTOMATIC VOLUME LEVELING AVL

FAST FILTER IF-PLL FFI

ENABLE VERTICAL GUARD (RGB BLANKING) EVG

EHT TRACKING MODE (HCO) EHT

OVERSCAN SWITCH OFF OSO

AUTO COLOUR LIMIT ACL

FORCED COLOUR LIMIT FCO

SOUND SYSTEM M S-M

SOUND SYSTEM DK S-DK

SOUND SYSTEM I S-I

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

VMC

BTSC

SOUND SYSTEM BG S-BG

PLAYBACK SECAM P-SECAM

FE (RF) NTSC 3.58 F-N358

FE (RF) NTSC 4.43 F-N443

FE (RF) SECAM F-SECAM

VIDEO MUTE AT IDENT LOSS VMI

VIDEO MUTE AT PROGRAM/SOURCE CHANGE

HOTEL MODE HTL

REDUCED FM DEMODULATOR GAIN FOR BTSC SIGNAL

NUMBER OF EXTERNAL AV SOURCE AV 0 FOR1 AV/1 FOR 2AV 1 FIX

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

FM WINDOW SELECTION FMWS

SOUND MUTE BIT 0 SM0

SOUND MUTE BIT 1 SM1

THAI LANGUAGE THA

ARABIC LANGUAGE ARA

MALAY LANGUAGE MAL

CHINESE LANGUAGE CHI

FRENCH LANGUAGE FRE

RUSSIAN LANGUAGE RUS

FORCED V-SYNC SLICING LEVEL FSL

SAME AS (DRI-BS) DATA

32 CHG

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

CPT

SYNC OF OSD HP2

CHARGE PUMP TUNER

BILINGUAL BIL

IF AGC SPEED BIT 0 AGC0

IF AGC SPEED BIT 1 AGC1

PHI-1 TIME CONSTANT (RF) FOA-FE

PHI-1 TIME CONSTANT (RF) FOB-FE

PHI-1 TIME CONSTANT (OFF AIR) FOA-AV

PHI-1 TIME CONSTANT (OFF AIR) FOB-AV

LED BLINK SPEED LED_F

255 FIX

0(DISABLE)/1(ENABLE)

0(DISABLE)/1(ENABLE)

After sub-colour adjustment please up 6 step for colour offset

Fixed data, please do not change without specific instruction.

Note : Please set default value for colour offset before sub-colour adjustment.

COLOUR OFFSET (PAL) COL-OP : 8 ------> 14

2) *1: CHANGE COLOUR OFFSET AFTER ADJUST SUB-COLOUR.

VOLUME CONTROL PWM TABLE MSA

OUTPUT VERTICAL GUARD NDF

NOTE :

1) Please set the EEPROM initial data according to the value in parenthesis ( ) before adjustment.

COLOUR OFFSET (SECAM) COL-OS : 8------> 14

COLOUR OFFSET (NTSC358) COL-O3 : 4 ------> 10

5-2

COLOUR OFFSET (NTSC443) COL-O4 : 4 ------> 10

00H: 55H 02H: 53H

01H: 41H 03H: 36H

Address Data Address Data

After short JA122 & 124, and turn on the main power switch, read data from EEPROM

address 00H ~ 03H, and compare to the list below, if different, initialize the EEPROM.

01.C14-RM50(R)_E/p01-17 02.12.5, 14:185

EEPROM ITEMS OSD DATA LENGTH

AGC TAKE OVER POINT AGC 0~63 14 ADJ

VERTICAL SLOPE V-LIN 0~63 32 ADJ

VERTICAL AMPLITUDE V-AMP 0~63 32 ADJ

VERTICAL SHIFT V-CENT 0~63 32 ADJ

HORIZONTAL SHIFT H-CENT 0~63 32 ADJ

EAST-WEST WIDTH [EW] H-SIZE 0~63 32 FIX

HORIZONTAL PARALLELOGRAM EW// 0~63 32 FIX

EAST-WEST PARABOLA/WIDTH PARA 0~63 32 FIX

EAST-WEST UPPER CORNER PARABOLA COR(U) 0~63 32 FIX

EAST-WEST LOWER CORNER PARABOLA COR(L) 0~63 32 FIX

EAST-WEST TRAPEZIUM [TC] TRAPE 0~63 32 FIX

HORIZONTAL BOW HB 0~63 32 FIX

S-CORRECTION S-COR 0~63 0(22) FIX

WHITE POINT RED STD WHITE TEMP DRI-RS 0~63 32 FIX

WHITE POINT GREEN STD WHITE TEMP DRI-GS 0~63 32 ADJ

WHITE POINT BLUE STD WHITE TEMP DRI-BS 0~63 32 ADJ

WHITE POINT RED COOL WHITE TEMP DRI-RC 0~63 25 FIX

0~99 OR>99FOR NONE

WHITE POINT GREEN COOL WHITE TEMP DRI-GC 0~63 32 CHG (DRI-GS)-7DATA

WHITE POINT BLUE COOL WHITE TEMP DRI-BC 0~63

WHITE POINT RED WARM WHITE TEMP DRI-RW 0~63 32 FIX

WHITE POINT GREEN WARM WHITE TEMP DRI-GW 0~63 32 CHG (DRI-GS)-7 DATA

WHITE POINT BLUE WARM WHITE TEMP DRI-BW 0~63 32 CHG (DRI-BS)-7 DATA

MAX VOLUME SUB-VOL 0~63 63 FIX

SUB CONTRAST SUB-CON 0~63 63 FIX

SUB COLOUR SUB-COL 0~63 32 ADJ

SUB BRIGHTNESS SUB-BRI 0~63 32 ADJ

SUB TINT SUB-TINT 0~63 32 ADJ

SUB SHARPNESS SUB-SHP 0~63 32(20) FIX

MAX HOTEL VOLUME HTL-VOL 0~63 32 ADJ

HOTEL PROGRAM NUMBER HTL-PRG

OSD GRB REFERENCE RGB 0~15 15 FIX

BLACK LEVEL OFF-SET R CUT-R 0~63 32 ADJ

BLACK LEVEL OFF-SET G CUT-G 0~63 32 ADJ

CATHODE DRIVE LEVEL CDL 0~15 0(5) FIX

Y-DELAY TIME FOR PAL(TV) [YD] DL-PT 0~15 12 FIX

Y-DELAY TIME FOR SECAM(TV) [YD] DL-ST 0~15 15 FIX

Y-DELAY TIME FOR N358 (TV) [YD] DL-3T 0~15 12 FIX

Y-DELAY TIME FOR N443 (TV) [YD] DL-4T 0~15 12 FIX

Y-DELAY TIME FOR B/W (TV) [YD] DL-TV 0~15 12 FIX

Y-DELAY TIME FOR PAL (AV) [YD] DL-PA 0~15 12(9) FIX

Y-DELAY TIME FOR SECAM (AV) [YD] DL-SA 0~15 15 FIX

Y-DELAY TIME FOR N358 (AV) [YD] DL-3A 0~15 12(7) FIX

Y-DELAY TIME FOR N443 (AV) [YD] DL-4A 0~15 12 FIX

Y-DELAY TIME FOR B/W (AV) [YD] DL-AV 0~15 12 FIX

COLOUR OFFSET (PAL) COL-OP 0~15 8 CHG *1

COLOUR OFFSET (SECAM) COL-OS 0~15 8 CHG *1

5-1

5

C14-RM50

6-2

ITEMS DATA SETTING

LAST PROGRAM/CHANNEL 1

FLASHBACK PROGARM/CH 1

DIGIT 1

C-SYSTEM AUTO

S-SYSTEM *1

SKIP OFF

AFC ON

VOLUME 1

CONTRAST (MAX)

COLOUR (CENTER)

BRIGHTNESS (CENTER)

TINT (CENTER)

SHARPNESS (CENTER)

WHITE TEMP STANDARD

REMINDER TIMER In-active, "--:--"

ON TIMER In-active, "--:--"

OFF TIMER In-active, "--:--"

LAST POWER POWER-ON

LANGUAGE *1

BLUE BACK MUTE ON

HOTEL MODE OFF

0CHANNEL SKIP ON

LAST TV/AV TV

SHIPPING SETTING & CHECKING

selected.

(1) The following default data has been factory-set for the EEPROM follow by INTIAL DATA

MCL1

5 RUSSIAN D/K

INITIAL LANGUAGE SOUND SYSTEM

*1:Please refer defaults for LANGUAGE and SOUND SYSTEM per MODEL as follows.

45,000 20,000 12300K RUSSIAN D/K 6

RUSSIA

DESTINATION MAGNEYIC FIELD (V, H) nT BACKGROUND LANG. S-SYS LANG QTY

FACTORY SETTING BY MODEL

(Reference: Geomagnetism Adjustment)

LANGUAGE QTY: ENGLISH/CHINESE/FRENCH/ARABIC/MALAY/RUSSIAN

6-1

INITIAL SETTING

0

1 48.25 B/G

2 62.25 B/G

3 77.25 D/K

CH-No. Fv (MHz) SOUND SYS

(1) Please set the MCL to MCL1.

(2)After set the MCL please set the INITIAL SETTING to INITIAL 5.

01.C14-RM50(R)_E/p01-17 02.12.5, 14:186

4 175.25 B/G

5 182.25 B/G

6 183.25 D/K

7 191.25 D/K

8 196.25 B/G

9 210.25 B/G

10 224.25 B/G

11 471.25 B/G

12 487.25 I

13 503.25 B/G

14 575.25 B/G

15 599.25 B/G

16 621.25 M

17 639.25 D/K

18 703.25 B/G

19 735.25 I

20 767.25 B/G

21 815.25 B/G

22 855.25 I

23 855.25 B/G

24 55.25 M

25 83.25 M

26 183.25 M

27 193.25 M

28 217.25 M

29 471.25 M

30 477.25 M

31 693.25 M

32 885.25 M

33 112.25 B/G

34 168.25 B/G

35

36 294.25 B/G

37 463.25 B/G

38

39 647.25 B/G

40 663.25 B/G

41 679.25 B/G

42 174.95 B/G

43 175.55 B/G

6

C14-RM50

a

b

A

B

A

B

A = B

A = B

Rank "A"

(on the right of the CRT)

Rank "A"

(on the left of the CRT)

» Bias box: About 4.5 V

Oscilloscope

0.1V

TV Set

Bias box

TP201+

+

–

–

E-9 CH

P C

10k

100k

1n60

75ohm

IF OUT

-1.5+/-0.8dB

1000p

Oscilloscope

Green-only

Blue-only

Red-only

Signal-colour

screen cleared

Fig. 1-1

(0.02 gauss)

(0.45 gauss)

PURITY ADJUSTMENT

the magnetic field.

Vertical BV : +0.045 mT

Horizontal Bh : +0.02mT

beam current to about 500 µA.

coil.

1. Receive the GREEN-ONLY signal. Adjust the

2. Degauss the CRT enough with the degausing

Note: Follow the job instruction sheet to adjust

PURITY ADJ.

1

NO. Adjustment part Adjusting procedure and conditions Waveform and others

(see page 6.)

3. Maintain the purity magnet at the zero mag-

netic field and keep the static convergence

roughly adjusted.

through the microscope. Adjust the landings

to A rank requirement.

4. Observe the points a, b, as shown in Fig. 1-1

5. Orient the raster rotation to 0 eastward.

6. Tighten up the deflection coil screws.

Fig. 1-2

(11kgf ± 2 kgf)

» Tightening torque: 108N ± 20 N

A rank requirements. If not, stick the magnet

sheet to correct it.

Note:This adjustment must be done after

7. Make sure the CRT corners landing meet the

Fig. 1-3

warming up the unit for 30 minutes

or longer with a beam current over

500µA.

change.

* For the following colours press R/C RGB key to

in NORMAL MODE, the colour

will change to RGB mono colour

mode.

* Press R/C RGB key for 1 second

7-2

Fig. 1

PIF ADJUSTMENT

but with no signal input.

Adjust the PLL data.

1. Get the tuner ready to receive the E-9 signal,

2. Connect the sweep generator's output cable

Tuner IFT

(PRESET)

1

NO. Adjustment part Adjusting procedure and conditions Waveform and others

ANCE probe with wave detector; see Fig.1) to

3. Adjust the sweep generator's to 80dBuV.

4. Connect the response lead (use LOW IMPED-

the tuner's IF output terminal. (This terminal

to the tuner antenna. (RF SWEEP)

Fig. 2

tion during this adjustment.

must have the probe alone connected).

with the waveform.

as shown in Fig. 2.

5. Set the RF AGC to 0 - 6 V with no saturation

6. Adjust the tuner IF coil to obtain the waveform

Note: Be sure to keep the tuner cover in posi-

For the 50 ohm signal strength

gauge, when not using 50/75

impedance adapter, signal

strength is 52 ±1 dBµV(75 ohm

open), instead of 57±1 dBµV

(75 ohm open).

The loss of using impedance

Note:

adapter

Precaution:

Fig. 3

AGC Terminal) as shown in Fig. 3.

» Signal Strength: 57 ±1 dBµV (75 ohm open)

1. Receive "PAL COLOUR BAR" signal.

2. Connect the oscilloscope to TP201 (Tuner’s

RF-AGC

TAKE OVER

POINT

ADJUSTMENT

(I2C BUS

CONTROL)

2

"AGC" bus data to obtain the Tuner output pin

drop 0.1 V below maximum voltage.

63~67dBµV, and make sure there is no noise.

3. Call "AGC" mode in service mode. Adjust the

sure that there is no cross modulation beat.

4. Change the antenna input signal to

5. Turn up the input signal to 90~95 dBµV to be

7-1

01.C14-RM50(R)_E/p01-17 02.12.5, 14:187

7

C14-RM50

t

3.3Vdc

0

RGB

BGR

R

G

B

R

G

B

B

G

R

B

G

R

RGB

BGR

Lacquer

Wedge "a"

Wedge

"b"

Wedge

"c"

About

100°

About

100°

4-pole magnet

6-pole magnet

CRT neck

Lacquer

Purity magnet

32mm

1 2 3 4 5

1 2 3 4 5

* Alternative Procedure:

(1) Step (1), (2), (3) and (4) are same

as beside procedure.

appear and make sure the colour

appear wheather red, green or blue.

test points as belowwhich is based

on colour appear at (2)

RED=TP851, GREEN=TP852,

BLUE=TP853

(3) Connect the oscilloscope to related

(2) Then continue adjust until retrace line

(4) Then adjust Screen VR until the tip

of signal reach 3.3Vdc

1

2

Line 3 is one step (data) brighter than line 2

Y : 0.275

# 12300°K X : 0.272

(MINOLTA COLOUR ANALYZER CA-

100)

*Note: Above Data can be UP/DOWN

DRI-BW="DRI-BS"-7

DRI-RC=25

LOW HIGH

10cd/m2 200cd/m2

by Volume key.

DRI-GC="DRI-GS"-7

* 12300°K DRI-GW="DRI-GS"-7

8-2

ing up the unit for 30 minutes or longer

with a beam current over 800µA.

RS/RW/RC, DRI-GS/GW/GC, DRI-BS/BW/BC,

CUT-R and CUT-G must be INITIAL DATA .

Remark

1. Before CRT cutoff adjustment, SUB-BRIGHT, DRI-

CRT CUTOFF

CRT CUT-OFF, BACKGROUND AND SUB-CONTRAST ADJUSTMENT

1

NO. Adjustment part Adjusting procedure and conditions Waveform and others

dark room.

2. CRT Cutoff adjustment must be done inside a

C BUS

2

CONTROL)

ADJUSTMENT

(I

NO VIDEO signal.

1. Switch TV to VIDEO mode,BLUE BACK OFF, with

Fig. a

tor.

screen variable resistor until colour raster suddenly

*4. Next, check AKB circuit function by slowly increase

2. Press R/C to set Picture Normal condition.

3. Frist off the screen by adjust screen variable resis-

On and Off (AKB start function).

5. Then continue adjust until retrace line appear.

6. Finally, slowly decrease the screen variable resistor

Fig. b

until screen retrace line(Not Raster) Cut Off.

*NOTE :

Must comfirm the AKB function in set before con-

tinue the next adjustment.

hatch pattern with 5 black level windows)

1. Call " SUB-BRI" in service mode. (Receive Cross-

2. Adjust the " SUB BRIGHT " bus data in order that the

SUB-

BRIGHTNESS

ADJUSMENT

2

line 1 and 2 have the same darkness wherelse line

3 is one step (data) brighter than line 2. Finally data

minus 1 to make line 1, 2, and 3 are in same level

(darkness).

3. Clear service mode.

1. Receive the "WHITE" pattern with BURST signal.

C BUS

2

(I

CONTROL)

WHITE

3

Fig. c

( - ) TP 603 ( + ).

2. Press R/C to set Picture NORMAL condition.

3. Connect the DC miliammeter between the TP 602

4. Check Beam current should be around 800µA.

5. Set Brightness Y by generator to High Brightness 200

C BUS

2

BALANCE

SERVICE

MODE ADJ

CONTROL)

(I

cd/m2 (MINOLTA CA-100)

Point Green Std (DRI-GS) and White Point Blue Std

6. Switch TV Set to service mode and adjust the White

12300°K (White). *NOTE

(DRI-BS) data to have a colour temperature of

7. Set BRIGHTNESS Y by generator to Low Bright-

ness, 10 cd/m2 (MINOLTA CA-100).

Note : This adjustment must be done after warm-

perature. Then go back NORMAL mode (High Bright-

ness) to check colour temperature.

If out of range go back to (1)

8. Adjust "CUT-R" & "CUT-G" to get desired colour tem-

Fig. d

*ADJUST DRI-GC/GW, DRI-BC/BW as following DATA,

after finishing DRI-BS and DRI-GS DATA ADJUST-

MENT.

DRI-RS=32 (FIXED), DRI-RW=32(FIXED)

DRI-BC="DRI-BS"

1. Receive the "Monoscope Pattern" signal.

2. Press R/C to set Picture NORMAL condition.

9. Clear the SERVICE mode.

Maximum

beam check

4

TP602 (–).

(Full Scale: 3 mA Range)

3. Connect the DC miliammeter between TP603 (+) &

4. Beam current must be within 800 ± 100 µA.

8-1

swing the deflection coil upward.

"c" and swing the deflection coil downward.

swing the deflection coil rightward.

CONVERGENCE ADJUSTMENT

mode.

1. Receive the "Crosshatch Pattern" signal.

2. Using the remote controller, call NORMAL

CONVER-

GENCE ADJ.

(To be done

1

NO. Adjustment part Adjusting procedure and conditions Waveform and others

angle in order to superpose the blue and red

colours.

angle in order to superpose the green colour

Static convergence

over the blue and red colours.

1. Turn the 4-pole magnet to a proper opening

2. Turn the 6-pole magnet to a proper opening

after the purity

adjustment.)

screen in the following steps.

a) Fig. 5-1: Drive the wedge at point "a" and

Dynamic convergence

1. Adjust the convergence on the fringes of the

b) Fig. 5-2: Drive the wedge at points "b" and

swing the deflection coil leftward.

c) Fig. 5-3: Drive the "c" wedge deeper and

d) Fig. 5-4: Drive the "b" wedge deeper and

tape over them.

2. Fix all the wedges on the CRT and apply glass

magnet unit (purity, 4-pole, 6-pole magnets)

and magnet unit lock screw.

Finally received the Red-only and Blue-only

3. Apply lacquer to the deflection yoke lock screw,

signals to make sure there is no other colours

on the screen.

8

01.C14-RM50(R)_E/p01-17 02.12.5, 14:188

Fig. 1-1

W

Y

Cy G Mg R

B

SAME LEVEL

Cy

G

B

W

Y 100%W

75%

Mg R

each short test.

* Select one of Q883/5/7 to do

C14-RM50

9-2

Range : 100mV/div. (AC) (Use Probe 10:1)

NTSC CHROMA ADJUSTMENT

AV in.

1. Receive the "NTSC 3.58 Color Bar" signal thru

C BUS

2

SUB-TINT

(I

1

NO. Adjustment part Adjusting procedure and conditions Waveform and others

Sweep time: 10 µsec/div.

BLUE-OUT.

»

»

2. Connect the oscilloscope to TP853 (P882 pin5)

CONTROL)

Adjust the "SUB-TINT" bus data to obtain the

3. Call the "SUB-TINT" mode in service mode.

waveform shown as Figure 1-1.

4. Clear the SERVICE mode.

short, make sure the protector ON and switch

1. Receive "Monoscope Pattern" signal.

2. Set CONTRAST MAX.

to standby mode.

3. Set BRIGHT MAX.

4. During the Collector & Emitter of Q883/5/7

1. Receive "Monoscope Pattern" signal.

PROTECTOR OPERATION CHECKING

BEAM

PROTECTOR

1

NO. Adjustment part Adjusting procedure and conditions Waveform and others

H. V PROTEC-

2

the protector is not work.

(R606 side).

2. Connect output of Bias Box to D607 cathode

TOR

3. Set voltage of Bias Box to 18V and make sure

the protector is work.

4. Set voltage of Bias Box to 27V, and make sure

testing in +B line, check all possible damaged

components on +B line.

1. Once finish rectified Electrolytic Capacitor short

Other

protectors

3

(Use random selected set for inspection)

pedance. Make sure the output is as specified

1. Receive the "PAL Color Bar" signal (100%

(1.0 Vp-p ±3 dB).

2. Terminate the Video output with a 75 ohm im-

3. Terminate the Audio output with a 10k ohm

make sure that the modes change in order of

TV, AV1, AV2 & TV again and the video & au-

impedance. Make sure the O/P is as specified

(1.76 Vp-p ±3 dB).

dio output are according to the input terminal

1. Using the TV/AV key on the remote controller,

for each mode.

White Color Bar, Sound 400 Hz 100% Mod).

A/V INPUT AND OUTPUT CHECKING

VIDEO AND

AUDIO OUT-

PUT CHECK

1

NO. Adjustment part Adjusting procedure and conditions Waveform and others

VIDEO AND

AUDIO INPUT

CHECK

2

Fig. 1-1

9-1

till the horizontal line in the center of

monoscope is just at the position where the

1. Receive Monoscope Pattern Signal.

2. Call the "V-LIN" mode.

C

2

BUS CON-

V-SLOPE (I

1

NO. Adjustment part Adjusting procedure and conditions Waveform and others

HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENT

blanking starts.

3. Increase or decrease "V-LIN" by Volume key

TROL)

till the picture is centered.

1. Call the "V-CENT" mode.

2. Increase or decrease "V-CENT" by Volume key

C BUS

2

V-CENTER

(I

CONTROL)

2

key to set overscan of 9.5% typical.

1. Call the "V-AMP" mode.

2. Increase or decrease "V - AMP" by Volume

C BUS

2

V-AMP

(I

CONTROL)

3

Adjustment Spec 9.5% range +1% -0%.

adjust V-Slope, V-Shift and V-Amp to makesure

adjustment is in acceptable Ring-Shaped.

1. SET DATA TO 22

* Check the E-5 CH Monoscope Pattern then re-

S-CORREC-

TION (I2C BUS

CONTROL)

4

1. Call the "H-CENT" mode.

2. Increase or decrease "H-CENT" by Volume key

H-CENTER

5

to center the picture horizontal.

1. SET DATA TO 20

SUB-

SHARPNESS

6

ing.

1. Receive the "Monoscope Pattern" signal.

2. Press R/C to set Picture NORMAL condition.

3. Adjust the focus control to get the best focus-

1 Focus

PAL CHROMA ADJUSTMENT

before proceed to sub-colour adjustment

1. Receive the "PAL Color Bar" signal.

Note:Please set default value for colour offset

C BUS

2

CONTROL)

SUB COLOUR

(I

1

NO. Adjustment part Adjusting procedure and conditions Waveform and others

» Range : 20 V/div. (AC) (Using 10:1 probe)

» Sweep time : 10 µsec/div.

to Red cathode. (D881 Cathode)

2. Press R/C to set Picture Normal condition.

3. Connect the oscilloscope

mode. Adjust SUB COLOUR bus data, so that

the 75% White & Red portions of PAL Color

4. Using the R/C call "SUB COL" in SERVICE

Bar be at the same level shown as Fig. 1-1.

COL-OP : 8 ------> 14 COL-O3 : 4 ------> 10

COL-OS : 8 ------> 14 COL-O4 : 4 ------> 10

5. After adjust Sub-Colour, change colour offset:

6. Clear the SERVICE mode.

9

01.C14-RM50(R)_E/p01-17 02.12.5, 14:189

C14-RM50

(Continued)

the COLOUR SYSTEM key to select modes

except PAL, check the COLOUR is not work-

ing properly. Then, select the "PAL" mode.

Check again its colour so that it is working prop-

erly.

press COLOUR SYSTEM key to select modes

except SECAM, check the COLOUR is not

working properly. Then, select the "SECAM"

1. Receive the "PAL COLOUR BAR" signal, press

2. Receive "SECAM COLOUR BAR" signal,

mode. Check again its colour so that it is work-

SYSTEM" to select B/G, I. Check the sound

output is not working properly. Select D/K and

check the sound output to make sure it is work-

ing properly.

nal thru AV, press COLOUR SYSTEM key to

select modes except N4.43/3.58, check the

COLOUR is not working properly. Then, se-

lect the "NTSC 4.43/3.58" mode. Check again

its colour so that it is working properly.

3. Receive "NTSC 4.43/3.58 COLOUR BAR" sig-

1. Receive "PAL-D/K" signal, press the "SOUND

ing properly.

2. Receive "PAL-I" signal, press the "SOUND

SYSTEM" to select B/G, D/K. Check the sound

output is not working properly. Select I and

check the sound output to make sure it is work-

ing properly.

sure the sound is heard from the speakers.

SYSTEM" to select I, D/K. Check the

sound output is not working properly. Select

B/G and check the sound output to make sure

3. Receive "PAL-B/G" signal, press the "SOUND

it is working properly.

Then put the unit in no signal state.

1. Receive "PAL COLOUR BAR" signal.

2. Turn up the volume control to maximum, make

3. Check the sound mute is effective.

4. Finally turn sound level of CTV to minimum.

Check OSD LANGUAGE quantity and type as

English, Russian, Chinese, French, Arabic and

Malay.

HEADPHONE JACK CHECKING

10-2

100% MODULATION (±50kHz Dev)

output with 400Hz sound and no sound out

1. Receive PAL Color BAR with SOUND 400Hz,

from speaker.

2. Maximum volume, and check the headphone

FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)

COLOUR

SYSTEM

9

NO. Adjustment part Adjusting procedure and conditions Waveform and others

SOUND

SYSTEM

10

NOISE MUTE

CHECKING

11

contrast, colour, bright,

Note:If nothing is display mean

OSD

LANGUAGE

12

tint or sharpness are all in

normal setting.

QUANTITY

CHECK

HEADPHONE

OUTPUT

CHECKING

1

NO. Adjustment part Adjusting procedure and conditions Waveform and others

10-1

the CONTRAST effect is OK or not.

1. Receive "Monoscope Pattern" signal.

2. Set P-Mode to select CONTRAST.

3. Press Volume Up/Down key to check whether

CONTRAST

key

FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)

1

NO. Adjustment part Adjusting procedure and conditions Waveform and others

01.C14-RM50(R)_E/p01-17 02.12.5, 14:1810

the COLOUR effect is OK or not.

1. Receive "Color Bar" signal.

2. Set P-Mode to select COLOUR.

3. Press Volume Up/Down key to check whether

2 COLOUR key

the BRIGHTNESS effect is OK or not.

1. Receive "Monoscope Pattern" signal.

2. Set P-Mode to select BRIGHTNESS.

3. Press Volume Up/Down key to check whether

BRIGHTNESS

key

3

in.

1. Receive the "NTSC Colour Bar" signal thru AV

2. Set P-Mode to select TINT.

4 TINT key

UP for GREEN direction and DOWN for PUR-

PLE direction whether is OK or not.

3. Press Volume Up/Down key to check TINT,

the SHARPNESS effect is OK or not.

1. Receive "Monoscope Pattern" signal.

2. Set P-mode to select SHARPNESS.

3. Press Volume Up/Down key to check whether

SHARPNESS

Key

5

10

channel number in green colour under AFT ON

condition.

1. All Ch (1~99) will have an OSD display of the

CH DISPLAY

COLOUR

6

is pressed, all the settings will be present to

normal setting.

(Normal setting value for every mode).

» CONTRAST : MAX

1. Once in PICTURE Mode, and theNORMAL key

7 NORMAL Key

» COLOUR : CENTER

» BRIGHTNESS : CENTER

» TINT : CENTER

» SHARPNESS : CENTER

1. Receive "Monoscope Pattern" signal.

2. Set FUNCTION to select WHITE TEMP.

3. Press Volume Up/Down key to check WHITE

8 White Temp

TEMP Option, STANDARD:

NORMAL SETTING, WARM for more RED-

DISH direction changing, COOL for more BLU-

ISH direction changing.

C14-RM50

ADDRESS

DATA

00

PASS WORD

55 00-FF

01

PASS WORD

4F 00-FF

02

PASS WORD

43 00-FF

03

PASS WORD

A1 00-FF

04

05

06

AGC TAKE-OVER

0E 00-3F

07

V-SLOPE

20 00-3F

08

V-AMPLITUDE

20 00-3F

09

V-CENTER

20 00-3F

0A

H-CENTER

20 00-3F

0B

H-SIZE

20 00-3F

0C

EW-PARALLELOGRAM

20 00-3F

0D

EW-PARABOLA/WIDTH

20 00-3F

0E

EW-UPPER CORNER

20 00-3F

0F

EW-LOWER CORNER

20 00-3F

10

EW-TRAPEZIUM

20 00-3F

11

HORIZONTAL-BOW

20 00-3F

12

S-CORRECTION

00 00-3F

13

14

15

16

DRIVE-R (STANDARD)

20 00-3F

17

DRIVE-G (STANDARD)

20 00-3F

18

DRIVE-B (STANDARD)

20 00-3F

19

DRIVE-R (WARM)

20 00-3F

1A

DRIVE-G (WARM)

20 00-3F

1B

DRIVE-B (WARM)

20 00-3F

1C

DRIVE-R (COOL)

19 00-3F

1D

DRIVE-G (COOL)

20 00-3F

1E

DRIVE-B (COOL)

20 00-3F

1F

20

21

22

SUB-VOLUME

3F 00-3F

23

SUB-CONTRAST

3F 00-3F

24

SUB-COLOUR

20 00-3F

25

SUB-BRIGHTNESS

20 00-3F

26

SUB-TINT

20 00-3F

27

SUB-SHARPNESS

20 00-3F

28

HTL-VOLUME

20 00-3F

29

HTL-POSITION

FF 00-FF

2A

2B

2C

2D

OSD-REFERENCE

0F 00-0F

2E

CUTOFF LEVEL -OFFSET R

20 00-3F

2F

CUTOFF LEVEL -OFFSET G

20 00-3F

30

CATHODE DRIVE LEVEL

00 00-0F

31

Y-DELAY (TV PAL)

0C 00-0F

32

Y-DELAY (TV SECAM)

0F 00-0F

33

Y-DELAY (TV N358)

0C 00-0F

34

Y-DELAY (TV N443)

0C 00-0F

35

Y-DELAY (TV BW)

0C 00-0F

36

Y-DELAY (AV PAL)

0C 00-0F

37

Y-DELAY (AV SECAM)

0F 00-0F

38

Y-DELAY (AV N358)

0C 00-0F

39

Y-DELAY (AV N443)

0C 00-0F

3A

Y-DELAY (AV BW)

0C 00-0F

3B

COLOUR-OFFSET (PAL)

08 00-0F

3C

COLOUR-OFFSET (SECAM)

08 00-0F

3D

COLOUR-OFFSET (N358)

04 00-0F

3E

COLOUR-OFFSET (N443)

04 00-0F

3F

SHARPNESS-OFFSET (PAL)

08 00-0F

MODEL MODEL

LETTER NO. LETTER NO.

(1) 20th August

2001:Change of

range & default.

MICON EEPROM EEPROM CHASSIS CTV FINAL

LAST INITIAL

SETTING DATA

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

DEFAULT RANGE

WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

REMARK

ADDRESS

DATA

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

40

SHARPNESS-OFFSET (SECAM)

04 00-0F

41

SHARPNESS-OFFSET (N358)

0C 00-0F

42

SHARPNESS-OFFSET (N443)

08 00-0F

43

44

FCO ACL OSO EHT EVG FFI AVL BKS

00-FF

45

SECAM N443 N358

PB-SECAM

BG I DK M

00-FF

46

SM1 SM0 FMWS AV BTSC HTL VMC VMI

00-FF

47

HP2 FSL RUS FRA CHN MLY ARB THA

00-FF

48

AGC1 AGC0 BIL CPTFOB-AV FOA-AV FOB-FE FOA-FE

NDF MSA LED-F

00-FF

00-03

49

4A

4B

4C

VOLUME

01 00-3C

4D

CONTRAST

3C 00-3C

4E

COLOUR

1E 00-3C

4F

BRIGHTNESS

1E 00-3C

50

TINT

1E 00-3C

51

SHARPNESS

1E 00-3C

52

53

54

55

POSITION/AV1/AV2

01 00-FF

56

FAV-POS A

0A 00-FF

57

FAV-POS B

14 00-FF

58

FAV-POS C

1E 00-FF

59

FAV-POS D

28 00-FF

5A

5B

5C

LAST POWER MODE

00 00-01

5D

WHITE-TEMP

00 00-02

5E

BLUE BACK

00 00-01

5F

LANGUAGE

00 00-07

60

LAST DIGIT MODE (1 OR 2)

00 00-01

61

62

SKIP 0 SKIP 1 SKIP 2 SKIP 3 SKIP 4 SKIP 5 SKIP 6 SKIP 7

80 00-FF

63

SKIP 8 SKIP 9 SKIP 10 SKIP 11 SKIP 12 SKIP 13 SKIP 14 SKIP 15

00 00-FF

64

SKIP 16 SKIP 17 SKIP 18 SKIP 19 SKIP 20 SKIP 21 SKIP 22 SKIP 23

00 00-FF

65

SKIP 24 SKIP 25 SKIP 26 SKIP 27 SKIP 28 SKIP 29 SKIP 30 SKIP 31

00 00-FF

66

SKIP 32 SKIP 33 SKIP 34 SKIP 35 SKIP 36 SKIP 37 SKIP 38 SKIP 39

00 00-FF

67

SKIP 40 SKIP 41 SKIP 42 SKIP 43 SKIP 44 SKIP 45 SKIP 46 SKIP 47

00 00-FF

68

SKIP 48 SKIP 49 SKIP 50 SKIP 51 SKIP 52 SKIP 53 SKIP 54 SKIP 55

00 00-FF

69

SKIP 56 SKIP 57 SKIP 58 SKIP 59 SKIP 60 SKIP 61 SKIP 62 SKIP 63

00 00-FF

6A

SKIP 64 SKIP 65 SKIP 66 SKIP 67 SKIP 68 SKIP 69 SKIP 70 SKIP 71

00 00-FF

6B

SKIP 72 SKIP 73 SKIP 74 SKIP 75 SKIP 76 SKIP 77 SKIP 78 SKIP 79

00 00-FF

6C

SKIP 80 SKIP 81 SKIP 82 SKIP 83 SKIP 84 SKIP 85 SKIP 86 SKIP 87

00 00-FF

6D

SKIP 88 SKIP 89 SKIP 90 SKIP 91 SKIP 92 SKIP 93 SKIP 94 SKIP 95

00 00-FF

6E

SKIP 96 SKIP 97 SKIP 98 SKIP 99

00 00-FF

6F

70

71

72

73

74

TUNING FREQUANCY (HIGHER PART)

S-SYS

POS 0

75

TUNING FREQUANCY (LOWER PART)

000:BG

76

S-SYS AFT (auto) C-SYS

001:I

77

TUNING FREQUANCY (HIGHER PART)

010:DK

POS 1

78

TUNING FREQUANCY (LOWER PART)

011:M

79

S-SYS AFT (auto) C-SYS

7A

TUNING FREQUANCY (HIGHER PART)

AFT

POS 2

7B

TUNING FREQUANCY (LOWER PART)

0:OFF

7C

S-SYS AFT (auto) C-SYS

1:ON

7D

TUNING FREQUANCY (HIGHER PART)

POS 3

7E

TUNING FREQUANCY (LOWER PART)

7F

S-SYS AFT (auto) C-SYS

MODEL MODEL

LETTER NO. LETTER NO.

1B

DE

53

3E

C4

00

MICON EEPROM EEPROM CHASSIS CTV FINAL

LAST INITIAL

SETTING DATA

DEFAULT RANGE

WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

REMARK

(1) 20th August 2001:

Added 3 new items.

11-2

MEMORY MAP

01.C14-RM50(R)_E/p01-17 02.12.5, 14:1811

11

11-1

C14-RM50

ADDRESS

DATA

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

80

TUNING FREQUANCY (HIGHER PART)

POS 4

81

TUNING FREQUANCY (LOWER PART)

82

S-SYS AFT (auto) C-SYS

83

TUNING FREQUANCY (HIGHER PART)

POS 5

84

TUNING FREQUANCY (LOWER PART)

85

S-SYS AFT (auto) C-SYS

86

TUNING FREQUANCY (HIGHER PART)

POS 6

87

TUNING FREQUANCY (LOWER PART)

88

S-SYS AFT (auto) C-SYS

89

TUNING FREQUANCY (HIGHER PART)

POS 7

8A

TUNING FREQUANCY (LOWER PART)

8B

S-SYS AFT (auto) C-SYS

8C

TUNING FREQUANCY (HIGHER PART)

POS 8

8D

TUNING FREQUANCY (LOWER PART)

8E

S-SYS AFT (auto) C-SYS

8F

TUNING FREQUANCY (HIGHER PART)

POS 9

90

TUNING FREQUANCY (LOWER PART)

91

S-SYS AFT (auto) C-SYS

92

TUNING FREQUANCY (HIGHER PART)

POS 10

93

TUNING FREQUANCY (LOWER PART)

94

S-SYS AFT (auto) C-SYS

95

TUNING FREQUANCY (HIGHER PART)

POS 11

96

TUNING FREQUANCY (LOWER PART)

97

S-SYS AFT (auto) C-SYS

98

TUNING FREQUANCY (HIGHER PART)

POS 12

99

TUNING FREQUANCY (LOWER PART)

9A

S-SYS AFT (auto) C-SYS

9B

TUNING FREQUANCY (HIGHER PART)

POS 13

9C

TUNING FREQUANCY (LOWER PART)

9D

S-SYS AFT (auto) C-SYS

9E

TUNING FREQUANCY (HIGHER PART)

POS 14

9F

TUNING FREQUANCY (LOWER PART)

A0

S-SYS AFT (auto) C-SYS

A1

TUNING FREQUANCY (HIGHER PART)

POS 15

A2

TUNING FREQUANCY (LOWER PART)

A3

S-SYS AFT (auto) C-SYS

A4

TUNING FREQUANCY (HIGHER PART)

POS 16

A5

TUNING FREQUANCY (LOWER PART)

A6

S-SYS AFT (auto) C-SYS

A7

TUNING FREQUANCY (HIGHER PART)

POS 17

A8

TUNING FREQUANCY (LOWER PART)

A9

S-SYS AFT (auto) C-SYS

AA

TUNING FREQUANCY (HIGHER PART)

POS 18

AB

TUNING FREQUANCY (LOWER PART)

AC

S-SYS AFT (auto) C-SYS

AD

TUNING FREQUANCY (HIGHER PART)

POS 19

AE

TUNING FREQUANCY (LOWER PART)

AF

S-SYS AFT (auto) C-SYS

B0

TUNING FREQUANCY (HIGHER PART)

POS 20

B1

TUNING FREQUANCY (LOWER PART)

B2

S-SYS AFT (auto) C-SYS

B3

TUNING FREQUANCY (HIGHER PART)

POS 21

B4

TUNING FREQUANCY (LOWER PART)

B5

S-SYS AFT (auto) C-SYS

B6

TUNING FREQUANCY (HIGHER PART)

POS 22

B7

TUNING FREQUANCY (LOWER PART)

B8

S-SYS AFT (auto) C-SYS

B9

TUNING FREQUANCY (HIGHER PART)

POS 23

BA

TUNING FREQUANCY (LOWER PART)

BB

S-SYS AFT (auto) C-SYS

BC

TUNING FREQUANCY (HIGHER PART)

POS 24

BD

TUNING FREQUANCY (LOWER PART)

BE

S-SYS AFT (auto) C-SYS

BF

TUNING FREQUANCY (HIGHER PART)

POS 25

MODEL MODEL

LETTER NO. LETTER NO.

MICON EEPROM EEPROM CHASSIS CTV FINAL

LAST INITIAL

SETTING DATA

DEFAULT RANGE

WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

REMARK

ADDRESS

DATA

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

C0

TUNING FREQUANCY (LOWER PART)

POS 25

C1

S-SYS AFT (auto) C-SYS

C2

TUNING FREQUANCY (HIGHER PART)

POS 26

C3

TUNING FREQUANCY (LOWER PART)

C4

S-SYS AFT (auto) C-SYS

C5

TUNING FREQUANCY (HIGHER PART)

POS 27

C6

TUNING FREQUANCY (LOWER PART)

C7

S-SYS AFT (auto) C-SYS

C8

TUNING FREQUANCY (HIGHER PART)

POS 28

C9

TUNING FREQUANCY (LOWER PART)

CA

S-SYS AFT (auto) C-SYS

CB

TUNING FREQUANCY (HIGHER PART)

POS 29

CC

TUNING FREQUANCY (LOWER PART)

CD

S-SYS AFT (auto) C-SYS

CE

TUNING FREQUANCY (HIGHER PART)

POS 30

CF

TUNING FREQUANCY (LOWER PART)

D0

S-SYS AFT (auto) C-SYS

D1

TUNING FREQUANCY (HIGHER PART)

POS 31

D2

TUNING FREQUANCY (LOWER PART)

D3

S-SYS AFT (auto) C-SYS

D4

TUNING FREQUANCY (HIGHER PART)

POS 32

D5

TUNING FREQUANCY (LOWER PART)

D6

S-SYS AFT (auto) C-SYS

D7

TUNING FREQUANCY (HIGHER PART)

POS 33

D8

TUNING FREQUANCY (LOWER PART)

D9

S-SYS AFT (auto) C-SYS

DA

TUNING FREQUANCY (HIGHER PART)

POS 34

DB

TUNING FREQUANCY (LOWER PART)

DC

S-SYS AFT (auto) C-SYS

DD

TUNING FREQUANCY (HIGHER PART)

POS 35

DE

TUNING FREQUANCY (LOWER PART)

DF

S-SYS AFT (auto) C-SYS

E0

TUNING FREQUANCY (HIGHER PART)

POS 36

E1

TUNING FREQUANCY (LOWER PART)

E2

S-SYS AFT (auto) C-SYS

E3

TUNING FREQUANCY (HIGHER PART)

POS 37

E4

TUNING FREQUANCY (LOWER PART)

E5

S-SYS AFT (auto) C-SYS

E6

TUNING FREQUANCY (HIGHER PART)

POS 38

E7

TUNING FREQUANCY (LOWER PART)

E8

S-SYS AFT (auto) C-SYS

E9

TUNING FREQUANCY (HIGHER PART)

POS 39

EA

TUNING FREQUANCY (LOWER PART)

EB

S-SYS AFT (auto) C-SYS

EC

TUNING FREQUANCY (HIGHER PART)

POS 40

ED

TUNING FREQUANCY (LOWER PART)

EE

S-SYS AFT (auto) C-SYS

EF

TUNING FREQUANCY (HIGHER PART)

POS 41

F0

TUNING FREQUANCY (LOWER PART)

F1

S-SYS AFT (auto) C-SYS

F2

TUNING FREQUANCY (HIGHER PART)

POS 42

F3

TUNING FREQUANCY (LOWER PART)

F4

S-SYS AFT (auto) C-SYS

F5

TUNING FREQUANCY (HIGHER PART)

POS 43

F6

TUNING FREQUANCY (LOWER PART)

F7

S-SYS AFT (auto) C-SYS

F8

TUNING FREQUANCY (HIGHER PART)

POS 44

F9

TUNING FREQUANCY (LOWER PART)

FA

S-SYS AFT (auto) C-SYS

FB

TUNING FREQUANCY (HIGHER PART)

POS 45

FC

TUNING FREQUANCY (LOWER PART)

TUNING FREQUANCY (HIGHER PART)

TUNING FREQUANCY (LOWER PART)

FD

S-SYS AFT (auto) C-SYS

FE

POS 46

FF

MODEL MODEL

LETTER NO. LETTER NO.

MICON EEPROM EEPROM CHASSIS CTV FINAL

LAST INITIAL

SETTING DATA

DEFAULT RANGE

WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

REMARK

12-2

01.C14-RM50(R)_E/p01-17 02.12.5, 14:1812

12

12-1

C14-RM50

ADDRESS

DATA

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

100

POS 46

101

TUNING FREQUANCY (HIGHER PART)

POS 47

102

TUNING FREQUANCY (LOWER PART)

103

S-SYS AFT (auto) C-SYS

S-SYS AFT (auto) C-SYS

104

TUNING FREQUANCY (HIGHER PART)

POS 48

105

TUNING FREQUANCY (LOWER PART)

106

S-SYS AFT (auto) C-SYS

107

TUNING FREQUANCY (HIGHER PART)

POS 49

108

TUNING FREQUANCY (LOWER PART)

109

S-SYS AFT (auto) C-SYS

10A

TUNING FREQUANCY (HIGHER PART)

POS 50

10B

TUNING FREQUANCY (LOWER PART)

10C

S-SYS AFT (auto) C-SYS

10D

TUNING FREQUANCY (HIGHER PART)

POS 51

10E

TUNING FREQUANCY (LOWER PART)

10F

S-SYS AFT (auto) C-SYS

110

TUNING FREQUANCY (HIGHER PART)

POS 52

111

TUNING FREQUANCY (LOWER PART)

112

S-SYS AFT (auto) C-SYS

113

TUNING FREQUANCY (HIGHER PART)

POS 53

114

TUNING FREQUANCY (LOWER PART)

115

S-SYS AFT (auto) C-SYS

116

TUNING FREQUANCY (HIGHER PART)

POS 54

117

TUNING FREQUANCY (LOWER PART)

118

S-SYS AFT (auto) C-SYS

119

TUNING FREQUANCY (HIGHER PART)

POS 55

11A

TUNING FREQUANCY (LOWER PART)

11B

S-SYS AFT (auto) C-SYS

11C

TUNING FREQUANCY (HIGHER PART)

POS 56

11D

TUNING FREQUANCY (LOWER PART)

11E

S-SYS AFT (auto) C-SYS

11F

TUNING FREQUANCY (HIGHER PART)

POS 57

120

TUNING FREQUANCY (LOWER PART)

121

S-SYS AFT (auto) C-SYS

122

TUNING FREQUANCY (HIGHER PART)

POS 58

123

TUNING FREQUANCY (LOWER PART)

124

S-SYS AFT (auto) C-SYS

125

TUNING FREQUANCY (HIGHER PART)

POS 59

126

TUNING FREQUANCY (LOWER PART)

127

S-SYS AFT (auto) C-SYS

128

TUNING FREQUANCY (HIGHER PART)

POS 60

129

TUNING FREQUANCY (LOWER PART)

12A

S-SYS AFT (auto) C-SYS

12B

TUNING FREQUANCY (HIGHER PART)

POS 61

12C

TUNING FREQUANCY (LOWER PART)

12D

S-SYS AFT (auto) C-SYS

12E

TUNING FREQUANCY (HIGHER PART)

POS 62

12F

TUNING FREQUANCY (LOWER PART)

130

S-SYS AFT (auto) C-SYS

131

TUNING FREQUANCY (HIGHER PART)

POS 63

132

TUNING FREQUANCY (LOWER PART)

133

S-SYS AFT (auto) C-SYS

134

TUNING FREQUANCY (HIGHER PART)

POS 64

135

TUNING FREQUANCY (LOWER PART)

136

S-SYS AFT (auto) C-SYS

137

TUNING FREQUANCY (HIGHER PART)

POS 65

138

TUNING FREQUANCY (LOWER PART)

139

S-SYS AFT (auto) C-SYS

13A

TUNING FREQUANCY (HIGHER PART)

POS 66

13B

TUNING FREQUANCY (LOWER PART)

13C

S-SYS AFT (auto) C-SYS

13D

TUNING FREQUANCY (HIGHER PART)

POS 67

13E

TUNING FREQUANCY (LOWER PART)

13F

S-SYS AFT (auto) C-SYS

MODEL MODEL

LETTER NO. LETTER NO.

MICON EEPROM EEPROM CHASSIS CTV FINAL

LAST INITIAL

SETTING DATA

DEFAULT RANGE

WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

REMARK

ADDRESS

DATA

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

140

TUNING FREQUANCY (HIGHER PART)

POS 68

141

TUNING FREQUANCY (LOWER PART)

142

S-SYS AFT (auto) C-SYS

143

TUNING FREQUANCY (HIGHER PART)

POS 69

144

TUNING FREQUANCY (LOWER PART)

145

S-SYS AFT (auto) C-SYS

146

TUNING FREQUANCY (HIGHER PART)

POS 70

147

TUNING FREQUANCY (LOWER PART)

148

S-SYS AFT (auto) C-SYS

149

TUNING FREQUANCY (HIGHER PART)

POS 71

14A

TUNING FREQUANCY (LOWER PART)

14B

S-SYS AFT (auto) C-SYS

14C

TUNING FREQUANCY (HIGHER PART)

POS 72

14D

TUNING FREQUANCY (LOWER PART)

14E

S-SYS AFT (auto) C-SYS

14F

TUNING FREQUANCY (HIGHER PART)

POS 73

150

TUNING FREQUANCY (LOWER PART)

151

S-SYS AFT (auto) C-SYS

152

TUNING FREQUANCY (HIGHER PART)

POS 74

153

TUNING FREQUANCY (LOWER PART)

154

S-SYS AFT (auto) C-SYS

155

TUNING FREQUANCY (HIGHER PART)

POS 75

156

TUNING FREQUANCY (LOWER PART)

157

S-SYS AFT (auto) C-SYS

158

TUNING FREQUANCY (HIGHER PART)

POS 76

159

TUNING FREQUANCY (LOWER PART)

15A

S-SYS AFT (auto) C-SYS

15B

TUNING FREQUANCY (HIGHER PART)

POS 77

15C

TUNING FREQUANCY (LOWER PART)

15D

S-SYS AFT (auto) C-SYS

15E

TUNING FREQUANCY (HIGHER PART)

POS 78

15F

TUNING FREQUANCY (LOWER PART)

160

S-SYS AFT (auto) C-SYS

161

TUNING FREQUANCY (HIGHER PART)

POS 79

162

TUNING FREQUANCY (LOWER PART)

163

S-SYS AFT (auto) C-SYS

164

TUNING FREQUANCY (HIGHER PART)

POS 80

165

TUNING FREQUANCY (LOWER PART)

166

S-SYS AFT (auto) C-SYS

167

TUNING FREQUANCY (HIGHER PART)

POS 81

168

TUNING FREQUANCY (LOWER PART)

169

S-SYS AFT (auto) C-SYS

16A

TUNING FREQUANCY (HIGHER PART)

POS 82

16B

TUNING FREQUANCY (LOWER PART)

16C

S-SYS AFT (auto) C-SYS

16D

TUNING FREQUANCY (HIGHER PART)

POS 83

16E

TUNING FREQUANCY (LOWER PART)

16F

S-SYS AFT (auto) C-SYS

170

TUNING FREQUANCY (HIGHER PART)

POS 84

171

TUNING FREQUANCY (LOWER PART)

172

S-SYS AFT (auto) C-SYS

173

TUNING FREQUANCY (HIGHER PART)

POS 85

174

TUNING FREQUANCY (LOWER PART)

175

S-SYS AFT (auto) C-SYS

176

TUNING FREQUANCY (HIGHER PART)

POS 86

177

TUNING FREQUANCY (LOWER PART)

178

S-SYS AFT (auto) C-SYS

179

TUNING FREQUANCY (HIGHER PART)

POS 87

17A

TUNING FREQUANCY (LOWER PART)

17B

S-SYS AFT (auto) C-SYS

17C

TUNING FREQUANCY (HIGHER PART)

TUNING FREQUANCY (HIGHER PART)

POS 88

17D

TUNING FREQUANCY (LOWER PART)

17E

S-SYS AFT (auto) C-SYS

17F

POS 89

MODEL MODEL

LETTER NO. LETTER NO.

MICON EEPROM EEPROM CHASSIS CTV FINAL

LAST INITIAL

SETTING DATA

DEFAULT RANGE

WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

REMARK

13-2

01.C14-RM50(R)_E/p01-17 02.12.5, 14:1813

13-1

13

C14-RM50

ADDRESS

DATA

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

180

POS 89

181

182

TUNING FREQUANCY (HIGHER PART)

POS 90

183

TUNING FREQUANCY (LOWER PART)

184

S-SYS AFT (auto) C-SYS

185

TUNING FREQUANCY (HIGHER PART)

POS 91

186

TUNING FREQUANCY (LOWER PART)

187

S-SYS AFT (auto) C-SYS

188

TUNING FREQUANCY (HIGHER PART)

POS 92

189

TUNING FREQUANCY (LOWER PART)

18A

S-SYS AFT (auto) C-SYS

18B

TUNING FREQUANCY (HIGHER PART)

POS 93

18C

TUNING FREQUANCY (LOWER PART)

18D

S-SYS AFT (auto) C-SYS

18E

TUNING FREQUANCY (HIGHER PART)

POS 94

18F

TUNING FREQUANCY (LOWER PART)

190

S-SYS AFT (auto) C-SYS

191

TUNING FREQUANCY (HIGHER PART)

POS 95

192

TUNING FREQUANCY (LOWER PART)

193

S-SYS AFT (auto) C-SYS

194

TUNING FREQUANCY (HIGHER PART)

POS 96

195

TUNING FREQUANCY (LOWER PART)

196

S-SYS AFT (auto) C-SYS

197

TUNING FREQUANCY (HIGHER PART)

POS 97

198

TUNING FREQUANCY (LOWER PART)

199

S-SYS AFT (auto) C-SYS

19A

TUNING FREQUANCY (HIGHER PART)

POS 98

19B

TUNING FREQUANCY (LOWER PART)

19C

S-SYS AFT (auto) C-SYS

19D

TUNING FREQUANCY (HIGHER PART)

POS 99

19E

TUNING FREQUANCY (LOWER PART)

19F

S-SYS AFT (auto) C-SYS

1A0

AV1

1A1

1A2

(auto) C-SYS

1A3

AV2

1A4

1A5

(auto) C-SYS

1A6

1A7

1A8

1A9

1AA

1AB

1AC

1AD

1AE

1AF

1B0

1B1

1B2

1B3

1B4

1B5

1B6

1B7

1B8

1B9

1BA

1BB

1BC

1BD

1BE

1BF

MODEL MODEL

LETTER NO. LETTER NO.

TUNING FREQUANCY (LOWER PART)

S-SYS AFT (auto) C-SYS

MICON EEPROM EEPROM CHASSIS CTV FINAL

LAST INITIAL

SETTING DATA

DEFAULT RANGE

WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

REMARK

ADDRESS

DATA

MICON EEPROM EEPROM CHASSIS CTV FINAL

LAST INITIAL

SETTING DATA

(HEX) D7 D6 D5 D4 D3 D2 D1 D0

DEFAULT RANGE

WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE

REMARK

1C0

1C1

1C2

1C3

1C4

1C5

1C6

1C7

1C8

1C9

1CA

1CB

1CC

1CD

1CE

1CF

1D0

1D1

1D2

1D3

1D4

1D5

1D6

1D7

1D8

1D9

1DA

1DB

1DC

1DD

1DE

1DF

1E0

1E1

1E2

1E3

1E4

1E5

1E6

1E7

1E8

1E9

1EA

1EB

1EC

1ED

1EE

1EF

1F0

1F1

1F2

1F3

1F4

1F5

1F6

1F7

1F8

1F9

1FA

1FB

1FC

1FD

1FE

1FF

MODEL MODEL

LETTER NO. LETTER NO.

14-2

01.C14-RM50(R)_E/p01-17 02.12.5, 14:1814

14-1

14

C14-RM50

Blown out.

Replace the fuse.

Check IC701, D701 and

C707.

The fuse is again blown out.

Does horizontal circuit

oscillate ?

Check IC605, IC751 and

IC801.

D1001 (Power LED Green)

turns on or turns ON/OFF.

Check T701 pin (7) voltage

(Approx. 310V at 220V AC)

Check F701.

Check Secondary Main+B

(Approx. 115V)

Check CRT connector K1-

K5 bias.

Check

C878.

Check

IC801.

Checking the

protector circuit.

Check R618 and R615.

D1001 (Power LED Green)

turns on.

Check R701, R707 and D709.

Check D758, IC702,

IC753.

TROUBLE SHOOTING TABLE

NO RASTER

HOTEL ON

PASSWORD ****

Set vol up/down by R/C key.

Input 1,3,7,9 by R/C key.

#1 Ch 1 is your selected channel

for hotel mode.

15-2

15-1

UA1 HOTEL MODE APPLICATION

Preset mode

Fine tuning

Skip mode

System selection

press the (one/two digit) {2} key and keep pressing it for five second, then you can see

the hotel mode with four digits password.

mode will be enable, you can switch on/off the hotel mode by using R/C (volume up/

down) {3} key.

How to enable/disable the "Hotel Mode?"

Ans: a) Press the R/C (FUNCTION) {1} key until language selection appear, within five second

b) Key in the four digits password starting with number "1", "3", "7", "9", then the hotel

Before set the hotel mode, it is better to choose ch 1 & set s-vol level Up to 75% full scale.

After set hotel mode, starting channel will be always ch 1 & maximum sound level out will

be set the half of full scale.

* We recommend

* If you set hotel mode in AV, starting channel will be the last ch which you received before

power off (same as normal operation)

When using hotel mode, user can control "contrast", "brightness", "sharpness" and "tint"

function.

But after power off, it will return to the initial setting.

CONDITION

You can’t use:–

The others function is allowed to be used.

15

01.C14-RM50(R)_E/p01-17 02.12.5, 14:1815

C14-RM50

TROUBLE SHOOTING TABLE

(Continued)

NEITHER VERTICAL NOR

HORIZONTAL SYNCHRONIZATION

CIRCUIT TO BE CHECKED:

» Sync. Separator Circuit.

NO VERTICAL SCAN

Vertical linearity and size

abnormal.

Check pins (16), (17) and

(34) of IC801.

DEFECTIVE VERTICAL AMP.

AND VERTICAL LINEARITY

Readjust vertical size.

(Bus Data)

Check IC501.

Check C503 and C507.

Check IC501.

Check R504, R503, R506,

R513, C517 and D501.

TROUBLE SHOOTING TABLE

(Continued)

NO PICTURE, NO SOUND

NO SOUND

CIRCUITS TO BE CHECKED:

» Tuner.

» PIF.

» Automatic Gain Control.

» (5V), (32V) Power Source.

CIRCUITS TO BE CHECKED:

» Sound system pins (28), (29)

and (44) of IC801.

» Sound Detector Circuit.

» Sound Switch and Att.

Control.

» Audio Output Circuit.

Check P301, P303 connector of

IC301 and peripheral circuit.

Check Q310, pins(4) and (6)

of IC801 and peripheral

circuit.

Does noise signal appear at

pin (44) of IC801 ?

Check IC801.

Check C356, C359

and peripheral

circuit.

Does signal appear at pins

(6) and (8) of IC301 ?

Does signal appear at pins(28)

and (29) of IC801?

No snow noise.

Does noise or signal appear at pin (40)

of IC801 ?

Noise increases but no signal is

received.

Check the tuner supply voltage LB must

be approx. 5V, BT must be approx. 32V.

and CH preset data check.

Check the tuner AGC

(TP201).

Does noise or

signal appear at

pin (38) of IC801 ?

Check IC801 and

its related circuit.

Does noise or

signal appear at

pins (23) and (24)

of IC801?

Check Q205 and

related circuit.

Check pin (1) of

SF201 and Tuner

related circuit.

Check pin (37) of

IC801 and related

circuit.

Check pin (27) of

IC801, Tuner and

related circuit.

Check pin(38) of

IC801.

Does the noise level increase at max.

Contrast, Brightness and Sound controls ?

16-2

01.C14-RM50(R)_E/p01-17 02.12.5, 14:1816

16

16-1

C14-RM50

TROUBLE SHOOTING TABLE

(Continued)

NO SPECIFIC COLOUR

Is some colour produced in

B/W broadcast reception ?

Is the white balance properly

adjusted ?

Readjust the white balance.

The picture colour is yellow.

The picture colour is magenta.

The picture colour is cyan.

Check Q871, Q883 and their

adjacent circuits.

Check Q870, Q885 and their

adjacent circuits.

Check Q872, Q887 and their

adjacent circuits.

Check IC801 and bias

control circuit.

NO SPECIFIC COLOUR

“PAL”/“SECAM”

(NO COLOUR SYNCHRONIZATION)

Check IC801, R801, R802,

R803, D804, D805, D806

and Q801.

Check X1001. (12MHz)

17-2

01.C14-RM50(R)_E/p01-17 02.12.5, 14:1817

17-1

17

C14-RM50

654321

A

B

C

D

E

F

G

H

CHASSIS LAYOUT

18

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3818

654321

A

B

C

D

E

F

G

H

BLOCK DIAGRAM:CRT and HEADPHONE Unit

Ë

CRT Unit

C14-RM50

Ë

HEADPHONE Unit

19

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3819

C14-RM50

87109654321

A

B

C

D

E

F

G

H

BLOCK DIAGRAM:MAIN Unit

20

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3820

1716 1918151413121110

C14-RM50

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3821

21

C14-RM50

1

6

q

yui

2

7

wert

3

8

4

9

5

0

1 Vp-p 2.5 Vp-p (H) 2.55 Vp-p (H) 3.35 Vp-p (H) 68 Vp-p (H)

66 Vp-p (H) 72 Vp-p (H) 3 Vp-p (V) 1.85 Vp-p (H) 150 Vp-p (H)

8.4 Vp-p (H) 1.3 Vp-p (V) 0.98 Vp-p (V) 43 Vp-p (V) 190 Vp-p (H)

1050 Vp-p (H) 2.4 Vp-p (V) 500 Vp-p

DESCRIPTION OF SCHEMATIC DIAGRAM

SAFETY NOTES:

1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE
REPLACING PARTS.

2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OP­ERATING.

IMPORTANT SAFETY NOTICE:

PARTS MARKED WITH “å” ( ) ARE IMPORTANT FOR
MAINTAINING THE SAFETY OF THE SET. BE SURE TO RE­PLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAIN­ING THE SAFETY AND PERFORMANCE OF THE SET.

SERVICE PRECAUTION:

THE AREA ENCLOSED BY THIS LINE (
CONNECTED WITH AC MAINS VOLTAGE.
WHEN SERVICING THE AREA, CONNECT AN ISOLATING TRANS­FORMER BETWEEN TV RECEIVER AND AC LINE TO ELIMINATE
HAZARD OF ELECTRIC SHOCK.

) IS DIRECTLY

WAVEFORMS

NOTES:

1. The unit of resistance “ohm” is omitted.
(K = 1000 ohms, M = Meg ohm).

2. All resistors are 1/10 watt, unless otherwise noted.

3. All capacitors are

µ

F, unless therwise noted. (P = µµF).

VOLTAGE MEASUREMENT CONDITIONS:

1. Voltage in parenthesis measured with no Signal.

2. Voltages without parenthesis measured with 3mVB&W or Colour­Signal.

3. All the voltages in each point are measured with VTVM.

WAVEFORM MEASUREMENT CONDITIONS:

1. Colour bar generator signal of 1.0V peak to peak applied at Pin
(40) of IC801.

2. Approximately 4.0 V AGC bias.

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3822

22

654321

A

B

C

D

E

F

G

H

SCHEMATIC DIAGRAM:CRT and HEADPHONE Unit

Ë

CRT Unit

C14-RM50

Ë

HEADPHONE Unit

23

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3823

C14-RM50

87109654321

A

B

C

D

E

F

G

H

SCHEMATIC DIAGRAM:MAIN Unit

24

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3824

1716 1918151413121110

C14-RM50

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3825

25

C14-RM50

654321

A

B

C

D

E

F

G

H

PRINTED WIRING BOARD ASSEMBLIES

PWB-B:CRT Unit (Wiring Side)

PWB-B:CRT Unit (Component Side)

26

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3826

654321

A

B

C

D

E

F

G

H

PWB-C:HEADPHONE Unit (Wiring Side )

C14-RM50

PWB-C:HEADPHONE Unit (Component Side )

PWB-C:HEADPHONE Unit (Chip Parts Side)

27

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3827

C14-RM50

654321

A

B

C

D

E

F

G

H

PWB-A:MAIN Unit (Wiring Side)

28

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3828

C14-RM50

654321

A

B

C

D

E

F

G

H

PWB-A:MAIN Unit (Component Side)

29

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3829

C14-RM50

654321

A

B

C

D

E

F

G

H

PWB-A:MAIN Unit (Chip Parts Side)

30

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3830

TOP VIEW

85

14

43

12

BASE
COLLECTOR
EMITTER

BASE
COLLECTOR
EMITTER

BCE

123

ANODE
(RED)
CATHODE
(COMMON)
ANODE
(GREEN)

1 3

112

+ ~ ~ -

ZR

T.R

COLLECTOR

COLLECTOR

BASE EMITTER

JC

COLLECTOR

BASE EMITTER

BASE EMITTER

H.R

COLLECTOR

BASE EMITTER

1

8

1

3

1

5

1357

2468

9

2SA1015
2SC1815

2SC2482

DX111PE

KA7808
KA7805

SE115N

STRF6653

TDA7056A

PX0037PE

2SD1877

M24C04W

FX0008GE D601A A1530AR

2SC2735

C3928AR

iX3368CE

LA7016

TA48M033

TDA8357

C14-RM50

SOLID STATE DEVICE BASE DIAGRAM

SIDE VIEW

02.C14-RM50(R)_E_p18-31 02.12.5, 14:3831

31

C14-RM50

REPLACEMENT PART LIST

The following service parts list are available for purchase. Serviceman may quote the components
shown in this page for servicing purposes.

PRODUCT SAFETY NOTE : Components marked with a å have special characteristics important to safety. The use of a substitute
replacement part which does not have the same safety characteristics may create shock, fire or other hazards. Don’t degrade the
safety of the receiver through improper servicing.

SYMBOL PART

No. No.

å ACC701 QACCB5003PEZZ AC Cord (For models with destination code 051 only).

å ACC701 QACCZ2008PEZZ AC Cord (For all models except destination code 051).

å C701 RC-FZ031SCEZZ 0.1 275V Metalized Plastic Film

å C721 RC-KZ0102GEZZ 680p 4KV Ceramic

å C759 VCKYPA1HB102K+ 1000p 50V Ceramic

DESCRIPTIONS

D701 RH-DX0111PEZZ DX0111PE

F301 QFS-J2521CEZZY Fuse (for C21-RM50, C21-RF50S, C21-RF50SN only)

å F701 QFS-C3229CEZZ Fuse

IC301 VHITDA7056A-1 IC TDA7056A (for C14-RM50, C14-RF50 only)

IC302 VHIAN5276//-1 IC AN5276 (for C21-RM50, C21-RF50S, C21-RF50SN only)

IC501 VHITDA8357/-1 TDA8357J/N1/S1

IC701 VHISTRF6653-1 IC STR-F6653 (for C14-RM50, C14-RF50 only)

IC701 VHISTRF6654-1 IC STR-F6654 (for C21-RM50, C21-RF50S, C21-RF50SN only)

å IC702 RH-FX0008GEZZ IC PC123FY8

IC801 RH-IX3368CEN6 I.C. (for C14-RM50, C14-RF50 only)

IC801 RH-IX3410CEN6 I.C. (for C21-RM50, C21-RF50S, C21-RF50SN only)

å L708 RCILG0095PEZZ Degaussing Coil (for C14-RM50, C14-RF50 only)

å L708 RCILG0069PEZZ Degaussing Coil (for C21-RM50, C21-RF50S, C21-RF50SN only)

Q602 VS2SD1877//1E TRS. 2SD1877 (for C14-RM50, C14-RF50 only)

Q602 VS2SD1586//1E TRS. 2SD2586 (for C21-RM50, C21-RF50S, C21-RF50SN only)

å R505 VRG-PD2HD330J 33 OHM 1/2W Fuse Re

å R712 VRG-PD2HD150J 15 OHM 1/2W Fuse Re

å R719 VRC-UA2HG825KY 8.2M OHM 1.2W SOLI

å R726 VRC-UA2HG825KY 8.2M OHM 1.2W SOLI

å S701 QSW-P0591CEZZ Power On/Off

å SC881 QSOCV0017PEZZ Socket (for C14-RM50, C14-RF50 only)

å SC882 QSOCV0016PEZZ CRT Socket (for C21-RM50, C21-RF50S, C21-RF50SN only)

å T601 RTRNZ0026PEZZ Transformer (for C21-RM50, C21-RF50S, C21-RF50SN only)

å T602 RTRNF0219PEZZ FBT (for C14-RM50, C14-RF50 only)

å T602 RTRNF0237PEZZ FBT (for C21-RM50, C21-RF50S, C21-RF50SN only)

å T603 RTRNZ0179CEZZ Transformer (for C14-RM50, C14-RF50 only)

å T701 RTRNZ0180PEZZ Transformer (for C14-RM50, C14-RF50 only)

å T701 RTRNZ0200PEZZ Transformer (for C21-RM50, C21-RF50S, C21-RF50SN only)

å TU201 VTUVTST5HD970 Tuner (for C14-RM50, C14-RF50 only)

å TU201 VTUCT5511+++ Tuner (for C21-RM50, C21-RF50S, C21-RF50SN only)

å VA700 RH-VX0073CEZZ Varistor

å RCILHA006WJZZ Deflection Yoke (for C14-RM50, C14-RF50 only)

å RCILH0193PEZZ Deflection Yoke (for C21-RM50, C21-RF50S, C21-RF50SN only)

RRMCGA066WJSA R/C (for C14-RM50, C14-RF50 only)

RRMCGA098WJSA Infrared R-C (for C21-RM50, C21-RF50S, C21-RF50SN only)

03.C14-RM50(R)_E_p32-end 02.12.5, 14:4332

32

Ref. No. Part No. Description Ref. No. Part No. Description

C14-RM50

PARTS LIST

FOR REFERENCE ONLY

The components shown in page 33 - 38 serve as a reference. It is not
meant for ordering of components for servicing purposes.
Do not quote any componets from these lists.

Ref. No. Part No. Description

PICTURE TUBE

å VB37GDA86X/1E Picture Tube
å RCiLHA006WJZZ Deflection Yoke
å L708 RCiLG0095PEZZ Degaussing Coil

QEARC1422PEZZ Grounding Strap
LHLDW0003PEKZ ADG Holder
MSPRT0001PEFJ CRT Spring
PMAGF3045CEZZ Purity Magnet
PSPAG0004PEZZ Spacer

PWB ASSEMBLIES

(NOT REPLACEMENT ITEM)

PWB-A DUNTK9988WED8 MAIN Unit
PWB-B DUNTK9990WED2 CRT Unit
PWB-C DUNTK9989WEV9 HEADPHONE Unit

PWB-A:DUNTK9988WED8

MAIN UNIT

TUNER

NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN

ASSEMBLY NOT INDEPENDENTLY

å TU201 VTUVTST5HD970 Tuner

INTEGRATED CIRCUITS

IC301 VHiTDA7056A-1 TDA7056A
IC501 VHiTDA8357/-1 TDA8357J/N1/S1
IC304 VHiLA7016//-1 LA7016
IC402 VHiLA7016//-1 LA7016
IC605 VHiKA7808AP-1 KIA7808API
IC701 VHiSTRF6653-1 STR-F6653

å IC702 RH-FX0008GEZZ PC123FY8

IC751 VHiTA48M033-1 TA48M033F
IC753 VHiSE115N//-1 SE115N
IC801 RH-iX3368CEN6 I.C.
IC1003 VHiM24C04W/-1 M24C04-WBN6
IC1005 VHiKA7805AP-1 KIA7805API

TRANSISTORS

Q201 VS2SC2735//1EY 2SC2735
Q203 VS2SC3928AR-1Y 2SC3928AR
Q205 VS2PC1815G+-1+ 2PC1815G
Q301 VS2SC3928AR-1Y 2SC3928AR
Q302 VS2SC3928AR-1Y 2SC3928AR
Q305 VS2SC3928AR-1Y 2SC3928AR
Q510 VS2PD601AR/-1Y 2PD601AR
Q601 VS2SC2482//-1+ 2SC2482
Q602 VS2SD1877//1E 2SD1877
Q603 VS2SC3928AR-1Y 2SC3928AR
Q723 VS2SC3928AR-1Y 2SC3928AR
Q752 VS2PC1815G+-1+ 2PC1815G
Q753 VS2PC1815G+-1+ 2PC1815G
Q801 VS2SA1530AR-1Y 2SA1530AR
Q802 VS2SA1530AR-1Y 2SA1530AR
Q1010 VS2SC3928AR-1Y 2SC3928AR

DIODES

D201 RH-EX0676GEZZY Zener Diode, 33V
D301 RH-DX0048GEZZY Diode
D305 RH-EX0631GEZZY Zener Diode, 9.1V
D308 RH-EX0631GEZZY Zener Diode, 9.1V
D311 VHDRL3Z////-1 Diode
D401 RH-EX0631GEZZY Zener Diode, 9.1V
D402 RH-EX0631GEZZY Zener Diode, 9.1V
D501 RH-EX0640GEZZY Zener Diode, 12V
D502 RH-DX0048GEZZY Diode
D503 RH-DX0048GEZZY Diode
D504 RH-DX0048GEZZY Diode
D505 RH-DX0127CEZZY Diode
D507 RH-DX0048GEZZY Diode
D508 RH-EX0647GEZZY Zener Diode, 15V
D509 RH-EX0647GEZZY Zener Diode, 15V
D510 RH-EX0263TAZZY Zener Diode, 8.2V
D511 RH-EX0263TAZZY Zener Diode, 8.2V
D512 RH-DX0048GEZZY Diode
D513 RH-DX0048GEZZY Diode
D514 RH-EX0903CEZZY Zener Diode, 27V
D515 RH-EX0903CEZZY Zener Diode, 27V
D518 RH-DX0048GEZZY Diode
D602 RH-DX0048GEZZY Diode
D603 RH-DX0131CEZZY Diode
D604 RH-DX0048GEZZY Diode
D605 RH-EX0253TAZZY Zener Diode, 3.3V
D606 RH-DX0048GEZZY Diode
D607 RH-EX0662GEZZY Zener Diode, 22V
D608 RH-EX0604GEZZY Zener Diode, 3.9V
D609 RH-DX0048GEZZY Diode
D610 RH-EX0662GEZZY Zener Diode, 24V
D611 RH-DX0302CEZZY Diode
D612 RH-EX0627GEZZY Zener Diode, 8.2V
D613 RH-DX0048GEZZY Diode

03.C14-RM50(R)_E_p32-end 02.12.5, 14:4333

33

C14-RM50

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

PWB-A:DUNTK9988WED8

MAIN UNIT (Continued)

D614 RH-DX0048GEZZY Diode
D701 RH-DX0111PEZZ Diode
D702 VHD1SS82///1AY Diode
D705 RH-DX0492CEZZY Diode
D706 VHD1SS82///1AY Diode
D707 VHD1SS82///1AY Diode
D708 RH-DX0400CEZZY Diode
D709 RH-DX0164CEZZY Diode
D710 RH-EX0601GEZZY Zener Diode, 3.6V
D711 VHD1SS82///1AY Diode
D713 RH-EX0621GEZZY Zener Diode, 6.8V
D750 RH-DX0048GEZZY Diode
D752 RH-DX0048GEZZY Diode
D753 RH-DX0471CEZZY Diode
D758 RH-DX0461CEZZ Diode
D760 RH-DX0048GEZZY Diode
D763 RH-DX0048GEZZY Diode
D801 RH-DX0048GEZZY Diode
D802 RH-DX0048GEZZY Diode
D803 RH-DX0048GEZZY Diode
D804 RH-DX0048GEZZY Diode
D805 RH-DX0048GEZZY Diode
D806 RH-DX0048GEZZY Diode
D810 RH-EX0610GEZZY Zener Diode, 4.7V
D813 RH-DX0048GEZZY Diode
D1001 RH-PX0037PEZZ Photo Diode
D1007 RH-EX0263TAZZY Zener Diode, 8.2V
D1008 RH-EX0263TAZZY Zener Diode, 8.2V
D1009 RH-EX0263TAZZY Zener Diode, 8.2V
D1010 RH-EX0263TAZZY Zener Diode, 8.2V

å VA700 RH-VX0073CEZZ Varistor

PACKAGED CIRCUITS

PR702 RMPTP0028CEZZ Packaged Circuit
X1001 RCRSB0300CEZZ Crystal, 12MHz

FILTERS AND COILS

CF201 RFiLC0465CEZZ Ceramic Filter
CF202 RFiLC0318CEZZ Ceramic Filter
SF201 RFiLC0442CEZZ SAW Filter
L203 VP-DF270K0000Y Peaking 27µH
L204 VP-XF1R2K0000Y Peaking 1.2µH
L205 VP-DF1R0K0000Y Peaking 1µH
L207 VP-DF1R0K0000Y Peaking 1µH
L208 VP-XF100K0000Y Peaking 10µH
L209 VP-XF6R8K0000Y Peaking 6.8µH
L212 VP-DF270K0000Y Peaking 27µH
L301 VP-DF1R0K0000Y Peaking 1µH
L401 VP-DF1R0K0000Y Peaking 1µH
L601 VP-CF1R0M0000Y Peaking 1µH
L603 RCiLP0225CEZZ Coil

å L701 RCiLF0021PEZZ Coil
å L702 RCiLF0036PEZZ Coil

L802 VP-DF100K0000Y Peaking 10µH
L803 VP-DF100K0000Y Peaking 10µH
L1030 VP-DF100K0000Y Peaking 10µH
L1050 VP-DF100K0000Y Peaking 10µH
L1051 VP-DF100K0000Y Peaking 10µH

TRANSFORMERS

å T602 RTRNF0219PEZZ FBT
å T603 RTRNZ0179CEZZ Transformer
å T701 RTRNZ0180PEZZ Transformer

CAPACITORS

[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]

C200 VCEA0A1CW476M+ 47 16V EL.
C203 VCKYCY1HF103Z 0.01 50V Ceramic
C204 VCEA0A1CW107M+ 100 16V EL.
C205 VCKYCY1HF103Z 0.01 50V Ceramic
C206 VCEA0A1HW106M+ 10 50V EL.
C207 VCKYCY1HF103Z 0.01 50V Ceramic

C208 VCKYCY1HF103Z 0.01 50V Ceramic
C209 VCKYCY1HF103Z 0.01 50V Ceramic
C210 VCKYCY1HF103Z 0.01 50V Ceramic
C211 VCKYCY1EF104Z 0.1 25V Ceramic
C212 VCEA0A1CW106M+ 10 16V EL.
C213 VCKYCY1HF223Z 0.022 50V Ceramic
C215 VCEA0A1CW476M+ 47 16V EL.
C216 VCKYCY1HB821K 820p 50V Ceramic
C217 VCKYCY1HB472K 4700p 50V Ceramic
C301 VCEA0A1CW107M+ 100 16V EL.
C302 VCEA0A1HW225M+ 2.2 50V EL.
C303 VCEA0A1CW106M+ 10 16V EL.
C304 VCQYTA1HM473J+ 0.047 50V Mylar
C305 VCQYTA1HM473J+ 0.047 50V Mylar
C312 VCQYTA1HM123J+ 0.012 50V Mylar
C314 VCEA0A1EW477M 470 25V EL.
C315 VCKYPA1HF103Z+ 0.01 50V Ceramic
C317 VCEA0A1HW224M+ 0.22 50V EL.
C318 VCKYCY1HB102K 1000p 50V Ceramic
C331 VCEA0A1HW105M+ 1 50V EL.
C332 VCEA0A1EW477M 470 25V EL.
C333 VCKYPA2HB102K+ 1000p 500V Ceramic
C356 VCKYCY1HB682K 6800p 50V Ceramic
C359 VCEA9M1CW106M+ 10 16V EL.
C360 VCEA9M1HW225M+ 2.2 50V EL.
C364 VCEA0A1CW106M+ 10 16V EL.
C371 VCEA0A1CW476M+ 47 16V EL.
C373 VCEA0A1CW107M+ 100 16V EL.
C374 VCEA0A1HW225M+ 2.2 50V EL.
C375 VCEAEA1HW225M+ 2.2 50V EL.
C379 VCEA0A1HW335M+ 3.3 50V EL.
C390 VCEA0A1HW105M+ 1 50V EL.
C405 VCEA0A1CW107M+ 100 16V EL.
C406 VCEA0A1CW477M+ 470 16V EL.
C407 VCEA0A1CW106M+ 10 16V EL.
C408 VCEA0A1CW106M+ 10 16V EL.
C409 VCKYCY1CF474Z 0.47 16V Ceramic
C410 VCKYCY1EF104Z 0.1 25V Ceramic
C411 VCKYCY1HB102K 1000p 50V Ceramic
C469 VCEA0A1HW105M+ 1 50V EL.
C501 VCKYCY1HF103Z 0.01 50V Ceramic
C502 VCKYCY1HF103Z 0.01 50V Ceramic
C503 VCEA0A1EW108M 1000 25V EL.
C504 VCKYCY1HF223Z 0.022 50V Ceramic
C506 VCQYTA1HM104J+ 0.1 50V Mylar
C507 VCEA0A1JW107M 100 63V EL.
C508 VCQYTA1HM103J+ 0.01 50V Mylar
C512 VCKYCY1HB102K 1000p 50V Ceramic
C513 VCKYCY1HB102K 1000p 50V Ceramic
C514 VCKYPA1HF103Z+ 0.01 50V Ceramic
C515 VCKYPA2HB102K+ 1000p 500V Ceramic
C516 VCEA0A1JW477M 470 63V EL.
C517 VCQYTA1HM104J+ 0.1 50V Mylar
C520 VCKYCY1CB104KY 0.1 16V Ceramic
C601 VCEA0A2EW106M 10 250V EL.
C602 VCQYTA1HM104J+ 0.1 50V Mylar
C603 VCEA0A1HW105M+ 1 50V EL.
C604 VCEA0A1HW105M+ 1 50V EL.
C605 VCKYPA1HF103Z+ 0.01 50V Ceramic
C606 VCKYCY1HF103Z 0.01 50V Ceramic
C607 VCEA0A1CW477M+ 470 16V EL.
C608 VCEA0A1EW476M+ 47 25V EL.
C609 VCEA0A1EW108M 1000 25V EL.
C610 VCFYSB2EB823J 0.082 250V Mylar
C611 VCKYPA2HB102K+ 1000p 500V Ceramic
C612 RC-EZ0776CEZZ 100 160V EL.
C613 VCFPFA2EB394J 0.39 250V M-Polyp.
C614 RC-KZ0035CEZZ 220p 2kV Ceramic
C615 VCFPPB2EB224J 0.22 250V M-Poly.
C616 VCFPVC3ZA622H 6200p 1.8kV M-Poly.
C617 VCKYPA2HB102K+ 1000p 500V Ceramic
C620 VCKYCY1EF104Z 0.1 25V Ceramic
C623 VCQYTA1HM222J+ 2200p 50V Mylar
C624 VCQYTA1HM472J+ 4700p 50V Mylar
C625 VCEA0A1HW105M+ 1 50V EL.
C626 VCKYCY1HF223Z 0.022 50V Ceramic

03.C14-RM50(R)_E_p32-end 02.12.5, 14:4334

34

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

C14-RM50

PWB-A:DUNTK9988WED8

MAIN UNIT (Continued)

C627 VCEA0A1HW106M+ 10 50V EL.
C628 VCEA0A1HW224M+ 0.22 50V EL.
C650 VCKYCY1EF104Z 0.1 25V Ceramic
C654 VCEA0A1CW476M+ 47 16V EL.
C700 VCQYTA1HM103J+ 0.01 50V Mylar

å C701 RC-FZ033SCEZZ 0.47

C702 RC-KZ0029CEZZ+ 0.01 250V Ceramic
C703 RC-KZ0029CEZZ+ 0.01 250V Ceramic
C704 VCKYPA2HB102K+ 1000p 500V Ceramic
C705 VCKYPA2HB102K+ 1000p 500V Ceramic
C707 RC-EZ1286CEZZ 150 400V EL.
C708 RC-KZ0029CEZZ+ 0.01 250V Ceramic
C709 VCQYTA1HM471J+ 470p 50V Mylar
C711 RC-KZ0039CEZZ 680p 2kV Ceramic
C712 VCQYTA1HM102J+ 1000p 50V Mylar
C713 RC-KZ007JCEZZ 0.01 250V Ceramic
C714 VCKYPH3DB561K 560p 2kV Ceramic
C715 VCKYPA2HB102K+ 1000p 500V Ceramic
C716 VCEA0A1EW107M+ 100 25V EL.
C717 VCQYTA1HM182J+ 1800p 50V Mylar
C718 VCEAGA2AW475M+ 4.7 100V EL.

å C721 RC-KZ0106GEZZ 3300p 250V Ceramic

C752 VCEA0A0JW107M+ 100 6.3V EL.
C753 VCKYPA2HB102K+ 1000p 500V Ceramic
C754 VCEA0A1CW477M+ 470 16V EL.
C755 VCEA0A1CW108M+ 1000 16V EL.
C757 VCEA0A1HW105M+ 1 50V EL.

å C759 VCKYPA1HB102K+ 1000p 50V Ceramic

C760 RC-KZ0039CEZZ 680p 2kV Ceramic
C761 RC-EZ0776CEZZ 100 160V EL.
C762 VCQYTA1HM473J+ 0.047 50V Mylar
C802 VCEA0A1CW337M+ 330 16V EL.
C803 VCEA9M1CW107M+ 100 16V EL.
C804 VCKYCY1HB222K 2200p 50V Ceramic
C805 VCKYCY1HB102K 1000p 50V Ceramic
C806 VCKYCY1HB102K 1000p 50V Ceramic
C807 VCKYCY1HB102KY 1000p 50V Ceramic
C808 VCEA0A1CW107M+ 100 16V EL.
C809 VCKYCY1HF223Z 0.022 50V Ceramic
C810 VCKYCY1EF104Z 0.1 25V Ceramic
C811 VCEA0A1CW107M+ 100 16V EL.
C812 VCFYFA1HA224J+ 0.22 50V Mylar
C813 VCFYFA1HA224J+ 0.22 50V Mylar
C814 VCKYCY1HB471K 470p 50V Ceramic
C1001 VCEA0A0JW107M+ 100 6.3V EL.
C1003 VCEA0A1CW106M+ 10 16V EL.
C1004 VCKYCY1CF474Z 0.47 16V Ceramic
C1005 VCKYCY1HF223Z 0.022 50V Ceramic
C1006 VCEA0A1CW106M+ 10 16V EL.
C1008 VCCCCY1HH330J 33p 50V Ceramic
C1009 VCCCCY1HH330J 33p 50V Ceramic
C1010 VCEA0A0JW107M+ 100 6.3V EL.
C1011 VCKYCY1HF223Z 0.022 50V Ceramic
C1012 VCKYCY1HF223Z 0.022 50V Ceramic
C1013 VCEA0A0JW107M+ 100 6.3V EL.
C1014 VCEA0A1CW106M+ 10 16V EL.
C1016 VCQYTA1HM104J+ 0.1 50V Mylar
C1018 VCKYCY1HB221K 220p 50V Ceramic
C1019 VCEA9M1HW225M+ 2.2 50V EL.

RESISTORS

[M-Ox.··· Metal Oxide, M-Film··· Metal Film]

RJ2 VRN-MD2AL000J 0 1/10W M-Film
RJ5 VRN-MD2AL000J 0 1/10W M-Film
RJ9 VRS-CY1JF000JY 0 1/16W M-Ox.
RJ10 VRN-MD2AL000J 0 1/10W M-Film
RJ11 VRN-MD2AL000J 0 1/10W M-Film
RJ12 VRN-MD2AL000J 0 1/10W M-Film
RJ13 VRN-MD2AL000J 0 1/10W M-Film
RJ15 VRN-MD2AL000J 0 1/10W M-Film
RJ19 VRS-CY1JF000JY 0 1/16W M-Ox.
RJ21 VRN-MD2AL000J 0 1/10W M-Film

AC250V

Prastic

RJ22 VRN-MD2AL000J 0 1/10W M-Film
RJ23 VRN-MD2AL000J 0 1/10W M-Film
RJ26 VRN-MD2AL000J 0 1/10W M-Film
RJ27 VRN-MD2AL000J 0 1/10W M-Film
RJ29 VRN-MD2AL000J 0 1/10W M-Film
RJ30 VRN-MD2AL000J 0 1/10W M-Film
RJ31 VRN-MD2AL000J 0 1/10W M-Film
RJ32 VRN-MD2AL000J 0 1/10W M-Film
RJ33 VRN-MD2AL000J 0 1/10W M-Film
RJ34 VRN-MD2AL000J 0 1/10W M-Film
RJ38 VRS-CY1JF000JY 0 1/16W M-Ox.
RJ41 VRN-MD2AL000J 0 1/10W M-Film
RJ43 VRN-MD2AL000J 0 1/10W M-Film
RJ51 VRN-MD2AL000J 0 1/10W M-Film
RJ53 VRN-MD2AL000J 0 1/10W M-Film
RJ61 VRN-MD2AL000J 0 1/10W M-Film
RJ64 VRN-MD2AL000J 0 1/10W M-Film
RJ66 VRS-CY1JF000JY 0 1/16W M-Ox.
RJ68 VRN-MD2AL000J 0 1/10W M-Film
RJ69 VRN-MD2AL000J 0 1/10W M-Film
RJ71 VRN-MD2AL000J 0 1/10W M-Film
RJ74 VRN-MD2AL000J 0 1/10W M-Film
RJ75 VRN-MD2AL000J 0 1/10W M-Film
RJ76 VRN-MD2AL000J 0 1/10W M-Film
RJ78 VRN-MD2AL000J 0 1/10W M-Film
RJ79 VRN-MD2AL000J 0 1/10W M-Film
RJ80 VRN-MD2AL000J 0 1/10W M-Film
RJ84 VRS-CY1JF000JY 0 1/16W M-Ox.
RJ85 VRS-CY1JF000JY 0 1/16W M-Ox.
RJ87 VRN-MD2AL000J 0 1/10W M-Film
RJ88 VRN-MD2AL000J 0 1/10W M-Film
RJ89 VRN-MD2AL000J 0 1/10W M-Film
RJ92 VRN-MD2AL000J 0 1/10W M-Film
RJ94 VRN-MD2AL000J 0 1/10W M-Film
RJ97 VRN-MD2AL000J 0 1/10W M-Film
RJ100 VRN-MD2AL000J 0 1/10W M-Film
RJ103 VRN-MD2AL000J 0 1/10W M-Film
RJ105 VRN-MD2AL000J 0 1/10W M-Film
RJ201 VRN-MD2AL000J 0 1/10W M-Film
RJ202 VRN-MD2AL000J 0 1/10W M-Film
RJ204 VRN-MD2AL000J 0 1/10W M-Film
RJ205 VRN-MD2AL000J 0 1/10W M-Film
RJ206 VRN-MD2AL000J 0 1/10W M-Film
RJ211 VRS-CY1JF000JY 0 1/16W M-Ox.
RJ213 VRS-CY1JF000JY 0 1/16W M-Ox.
RJ215 VRS-CY1JF000JY 0 1/16W M-Ox.
R201 VRN-MD2AL101J 100 1/10W M-Film
R202 VRN-MD2AL101J 100 1/10W M-Film
R203 VRD-RM2HD102JY 1k 1/2W Carbon
R204 VRD-RM2HD102JY 1k 1/2W Carbon
R205 VRD-RA2BE680JY 68 1/8W Carbon
R206 VRN-MD2AL122J 1.2k 1/10W M-Film
R207 VRN-MD2AL221J 220 1/10W M-Film
R208 VRN-MD2AL681J 680 1/10W M-Film
R209 VRN-MD2AL392J 3.9k 1/10W M-Film
R217 VRD-RA2BE392JY 3.9k 1/8W Carbon
R218 VRN-MD2AL102J 1k 1/10W M-Film
R219 VRN-MD2AL391J 390 1/10W M-Film
R220 VRN-MD2AL101J 100 1/10W M-Film
R221 VRN-MD2AL102J 1k 1/10W M-Film
R222 VRN-MD2AL681J 680 1/10W M-Film
R226 VRN-MD2AL750J 75 1/10W M-Film
R227 VRD-RM2HD330JY 33 1/2W Carbon
R228 VRD-RM2HD330JY 33 1/2W Carbon
R230 VRN-MD2AL101J 100 1/10W M-Film
R231 VRN-MD2AL153J 15k 1/10W M-Film
R232 VRD-RA2BE680JY 68 1/8W Carbon
R233 VRN-MD2AL181J 180 1/10W M-Film
R237 VRN-MD2AL272J 2.7k 1/10W M-Film
R238 VRN-MD2AL821J 820 1/10W M-Film
R239 VRN-MD2AL221J 220 1/10W M-Film
R301 VRN-MD2AL680J 68 1/10W M-Film
R302 VRN-MD2AL473J 47k 1/10W M-Film
R303 VRN-MD2AL473J 47k 1/10W M-Film
R304 VRN-MD2AL392J 3.9k 1/10W M-Film
R305 VRN-MD2AL100J 10 1/10W M-Film

03.C14-RM50(R)_E_p32-end 02.12.5, 14:4335

35

C14-RM50

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

PWB-A:DUNTK9988WED8

MAIN UNIT (Continued)

R307 VRD-RA2BE182JY 1.8k 1/8W Carbon
R308 VRD-RA2BE472JY 4.7k 1/8W Carbon
R320 VRN-MD2AL101J 100 1/10W M-Film
R321 VRN-MD2AL561J 560 1/10W M-Film
R328 VRN-MD2AL564J 560k 1/10W M-Film
R329 VRN-MD2AL332J 3.3k 1/10W M-Film
R330 VRN-MD2AL101J 100 1/10W M-Film
R331 VRN-MD2AL102J 1k 1/10W M-Film
R332 VRN-MD2AL561J 560 1/10W M-Film
R333 VRN-MD2AL103J 10k 1/10W M-Film
R334 VRN-MD2AL102J 1k 1/10W M-Film
R341 VRN-MD2AL332J 3.3k 1/10W M-Film
R342 VRN-MD2AL564J 560k 1/10W M-Film
R343 VRN-MD2AL104J 100k 1/10W M-Film
R344 VRN-MD2AL101J 100 1/10W M-Film
R357 VRN-MD2AL100J 10 1/10W M-Film
R378 VRN-VV3DBR68J 0.68 2W M-Film
R403 VRN-MD2AL101J 100 1/10W M-Film
R404 VRD-RA2BE820JY 82 1/8W Carbon
R406 VRN-MD2AL103J 10k 1/10W M-Film
R407 VRN-MD2AL101J 100 1/10W M-Film
R411 VRD-RA2BE820JY 82 1/8W Carbon
R412 VRN-MD2AL101J 100 1/10W M-Film
R501 VRN-MD2AL182J 1.8k 1/10W M-Film
R502 VRN-MD2AL182J 1.8k 1/10W M-Film
R503 VRD-RM2HD2R2JY 2.2 1/2W Carbon
R504 VRD-RM2HD150JY 15 1/2W Carbon
R505 VRG-PD2HD330J 33 1/2W Fuse Resistor
R506 VRD-RA2BE124JY 120k 1/8W Carbon
R508 VRD-RM2HD221JY 220 1/2W Carbon
R509 VRD-RM2HD1R0JY 1 1/2W Carbon
R510 VRN-MD2AL101J 100 1/10W M-Film
R511 VRN-MD2AL101J 100 1/10W M-Film
R513 VRD-RA2BE393JY 39k 1/8W Carbon
R514 VRN-MD2AL101J 100 1/10W M-Film
R515 VRN-MD2AL272J 2.7k 1/10W M-Film
R516 VRD-RM2HD223J 22k 1/2W Carbon
R520 VRS-CY1JF104JY 100k 1/16W M-Ox.
R521 VRS-CY1JF392JY 3.9k 1/16W M-Ox.
R602 VRN-VV3AB1R5J 1.5 1W M-Film
R603 VRD-RM2HD102JY 1k 1/2W Carbon
R604 VRD-RA2BE393JY 39k 1/8W Carbon
R605 VRD-RM2HD101JY 100 1/2W Carbon
R607 VRN-MD2AL102J 1k 1/10W M-Film
R608 VRN-MD2AL123J 12k 1/10W M-Film
R609 VRD-RA2BE273GY 27k 1/8W Carbon
R610 VRD-RA2BE153JY 15k 1/8W Carbon
R611 VRD-RA2EE823GY 82k 1/4W Carbon
R612 VRD-RA2BE103JY 10k 1/8W Carbon
R613 VRD-RA2BE103JY 10k 1/8W Carbon
R614 VRN-MD2AL103J 10k 1/10W M-Film
R615 VRS-KT3LB332J 3.3k 3W M-Ox.
R616 VRN-MD2AL102J 1k 1/10W M-Film
R617 VRD-RM2HD472JY 4.7k 1/2W Carbon
R618 VRS-KA3HG4R7K 4.7 5W M-Ox.
R619 VRD-RM2HD682JY 6.8k 1/2W Carbon
R622 VRD-RM2HD221JY 220 1/2W Carbon
R624 VRD-RA2BE101JY 100 1/8W Carbon
R625 VRN-MD2AL563J 56k 1/10W M-Film
R626 VRN-MD2AL472J 4.7k 1/10W M-Film
R627 VRD-RM2HD4R7JY 4.7 1/2W Carbon
R628 VRD-RM2HD470JY 47 1/2W Carbon
R629 VRS-CY1JF683JY 68k 1/16W M-Ox.
R630 VRN-MD2AL100J 10 1/10W M-Film
R631 VRN-MD2AL391J 390 1/10W M-Film
R632 VRN-MD2AL273J 27k 1/10W M-Film
R633 VRN-MD2AL102J 1k 1/10W M-Film
R635 VRN-MD2AL822J 8.2k 1/10W M-Film
R636 VRS-CY1JF223JY 22k 1/16W M-Ox.
R637 VRD-RM2HD181JY 180 1/2W Carbon
R638 VRN-MD2AL333J 33k 1/10W M-Film
R640 VRS-CY1JF563JY 56k 1/16W M-Ox.

R701 VRW-KQ3NC3R3K 3.3 7W Cement
R703 VRS-KT3LB473J 47k 3W M-Ox.
R705 VRD-RA2BE122JY 1.2k 1/8W Carbon
R706 VRD-RM2HD152JY 1.5k 1/2W Carbon
R707 VRS-KT3LB473J 47k 3W M-Ox.
R708 VRD-RM2HD272JY 2.7k 1/2W Carbon
R709 VRD-RA2BE681JY 680 1/8W Carbon
R710 VRN-VV3ABR39J 0.39 1W M-Film
R711 VRN-VV3ABR33J 0.33 1W M-Film

å R712 VRG-PD2HD150J 15 1/2W Fuse Resistor

R717 VRD-RM2HD124JY 120k 1/2W Carbon
R718 VRD-RM2HD124JY 120k 1/2W Carbon

å R719 VRC-UA2HG825KY 8.2M 1/2W Solid

R721 VRD-RA2BE393JY 39k 1/8W Carbon
R722 VRD-RM2HD124JY 120k 1/2W Carbon
R723 VRD-RA2BE684JY 680k 1/8W Carbon

å R726 VRC-UA2HG825KY 8.2M 1/2W Solid

R728 VRN-MD2AL272J 2.7k 1/10W M-Film
R750 VRD-RM2HD4R7JY 4.7 1/2W Carbon
R755 VRD-RA2BE222JY 2.2k 1/8W Carbon
R756 VRN-MD2AL152J 1.5k 1/10W M-Film
R758 VRD-RA2BE102JY 1k 1/8W Carbon
R759 VRN-MD2AL102J 1k 1/10W M-Film
R760 VRD-RA2BE471JY 470 1/8W Carbon
R761 VRD-RA2BE221JY 220 1/8W Carbon
R764 VRN-MD2AL272J 2.7k 1/10W M-Film
R766 VRD-RM2HD680JY 68 1/2W Carbon
R801 VRN-MD2AL101J 100 1/10W M-Film
R802 VRN-MD2AL101J 100 1/10W M-Film
R803 VRN-MD2AL101J 100 1/10W M-Film
R804 VRN-MD2AL101J 100 1/10W M-Film
R805 VRS-CY1JF822JY 8.2k 1/16W M-Ox.
R806 VRS-CY1JF123JY 12k 1/16W M-Ox.
R807 VRN-MD2AL103J 10k 1/10W M-Film
R808 VRN-MD2AL221J 220 1/10W M-Film
R809 VRD-RA2BE224JY 220k 1/8W Carbon
R812 VRN-MD2AL101J 100 1/10W M-Film
R813 VRN-MD2AL221J 220 1/10W M-Film
R1001 VRD-RA2BE221JY 220 1/8W Carbon
R1002 VRN-MD2AL331J 330 1/10W M-Film
R1003 VRN-MD2AL471J 470 1/10W M-Film
R1004 VRN-MD2AL821J 820 1/10W M-Film
R1005 VRD-RA2BE181JY 180 1/8W Carbon
R1011 VRN-MD2AL820J 82 1/10W M-Film
R1012 VRN-MD2AL391J 390 1/10W M-Film
R1013 VRN-MD2AL101J 100 1/10W M-Film
R1014 VRD-RA2BE101JY 100 1/8W Carbon
R1015 VRN-MD2AL332J 3.3k 1/10W M-Film
R1016 VRD-RA2BE101JY 100 1/8W Carbon
R1017 VRN-MD2AL332J 3.3k 1/10W M-Film
R1019 VRN-MD2AL472J 4.7k 1/10W M-Film
R1020 VRD-RA2BE101JY 100 1/8W Carbon
R1021 VRN-MD2AL153J 15k 1/10W M-Film
R1022 VRD-RA2BE101JY 100 1/8W Carbon
R1023 VRN-MD2AL101J 100 1/10W M-Film
R1024 VRN-MD2AL122J 1.2k 1/10W M-Film
R1025 VRN-MD2AL101J 100 1/10W M-Film
R1026 VRN-MD2AL224J 220k 1/10W M-Film
R1027 VRD-RA2BE101JY 100 1/8W Carbon
R1028 VRD-RA2BE391JY 390 1/8W Carbon
R1030 VRN-MD2AL102J 1k 1/10W M-Film
R1031 VRD-RA2BE562JY 5.6k 1/8W Carbon
R1032 VRN-MD2AL332J 3.3k 1/10W M-Film
R1033 VRD-RA2BE102JY 1k 1/8W Carbon
R1034 VRD-RA2BE101JY 100 1/8W Carbon
R1035 VRN-MD2AL332J 3.3k 1/10W M-Film
R1036 VRN-MD2AL332J 3.3k 1/10W M-Film
R1037 VRD-RA2BE101JY 100 1/8W Carbon
R1038 VRD-RA2BE101JY 100 1/8W Carbon
R1040 VRN-MD2AL101J 100 1/10W M-Film
R1041 VRN-MD2AL101J 100 1/10W M-Film
R1045 VRD-RA2BE271JY 270 1/8W Carbon
R1046 VRD-RA2BE101JY 100 1/8W Carbon
R1047 VRN-MD2AL101J 100 1/10W M-Film
R1067 VRN-MD2AL000J 0 1/10W M-Film

03.C14-RM50(R)_E_p32-end 02.12.5, 14:4336

36

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

C14-RM50

PWB-A:DUNTK9988WED8

MAIN UNIT (Continued)

å S701 QSW-P0591CEZZ Power On/Off

S1001 QSW-K0003AJZZ+ CH UP
S1002 QSW-K0003AJZZ+ CH Down
S1003 QSW-K0003AJZZ+ VOL UP
S1004 QSW-K0003AJZZ+ VOL Down
S1005 QSW-K0003AJZZ+ Picture

å F701 QFS-C3229CEZZ Fuse, T3.15A/250V

FH701 QFSHD1014CEZZ+ Fuse Holder
FH702 QFSHD1013CEZZ+ Fuse Holder
FB306 RBLN-0091GEZZY Ferrite Bead
FB501 RBLN-0091GEZZY Ferrite Bead
FB502 RBLN-0091GEZZY Ferrite Bead
FB602 RBLN-0091GEZZY Ferrite Bead
FB701 RBLN-0091GEZZY Ferrite Bead
FB702 RBLN-0091GEZZY Ferrite Bead
FB751 RBLN-0091GEZZY Ferrite Bead
FB752 RBLN-0091GEZZY Ferrite Bead
J402 QJAKE0211CE04 Jack
J403 QJAKE0211CE09 Jack
J405 QJAKH0044AJZZ Jack
P301 QPLGN0441CEZZ Plug, 4-pin(S)
P303 QPLGN0541CEZZ Plug, 5-pin(HP)
P502 QPLGN0660CEZZ Plug, 6-pin(F)
P602 QPLGN0641CEZZ Plug, 6-pin(H)
P701 QPLGN0260CEZZ Plug, 2-pin(G)
P712 QPLGN0269GEZZ Plug, 2-pin(A)
P1001 QPLGN0541CEZZ Plug, 5-pin(K)
P1002 QPLGN0541CEZZ Plug, 5-pin(BC)
RDA501
RDA701
RDA754
RDA756
RMC1001

PRDAR0283PEFW Heat Sink, for IC501
PRDAR0260PEFW Heat Sink, for IC701
PRDAR0224PEFW Heat Sink, for Q602
PRDAR0248PEFW Heat Sink, for IC301
RRMCU0222CEZZ R/C Receiver
LHLDP1066PE00 LED Holder

SWITCHES

MISCELLANEOUS PARTS

PWB-B:DUNTK9990WED2

CRT UNIT

TRANSISTORS

Q870 RH-TX0110BMZZ+ TX0110BM
Q871 RH-TX0110BMZZ+ TX0110BM
Q872 RH-TX0110BMZZ+ TX0110BM
Q883 RH-TX0124BMZZ+ TX0124BM
Q885 RH-TX0124BMZZ+ TX0124BM
Q887 RH-TX0124BMZZ+ TX0124BM

DIODES

D811 RH-DX0048GEZZY Diode
D812 RH-DX0048GEZZY Diode
D880 RH-DX0048GEZZY Diode
D881 RH-DX0048GEZZY Diode
D882 RH-DX0048GEZZY Diode
D883 VHD1SS244//-1Y 1SS244
D884 VHD1SS244//-1Y 1SS244
D885 VHD1SS244//-1Y 1SS244
D886 VHD1SS244//-1Y 1SS244
D887 VHD1SS244//-1Y 1SS244
D888 VHD1SS244//-1Y 1SS244

CAPACITORS

[EL.··· Electrolytic]

C871 VCKYPA1HB471K+ 470p 50V Ceramic
C872 VCKYPA1HB471K+ 470p 50V Ceramic
C873 VCKYPA1HB471K+ 470p 50V Ceramic
C875 VCKYPA2HB102K+ 1000p 500V Ceramic
C876 RC-KZ0150CEZZ 1000p 3kV Ceramic
C878 VCEA0A2EW106M 10 250V EL.
C880 VCKYPA1HB471K+ 470p 50V Ceramic
C881 VCKYPA1HB471K+ 470p 50V Ceramic
C882 VCKYPA1HB471K+ 470p 50V Ceramic

RESISTORS

[M-Ox.··· Metal Oxide]

R879 VRD-RA2BE471JY 470 1/8W Carbon
R880 VRD-RA2BE471JY 470 1/8W Carbon
R881 VRD-RA2BE471JY 470 1/8W Carbon
R882 VRS-VV3AB153J 15k 1W M-Ox.
R883 VRD-RM2HD272JY 2.7k 1/2W Carbon
R884 VRS-VV3AB153J 15k 1W M-Ox.
R885 VRD-RM2HD272JY 2.7k 1/2W Carbon
R886 VRS-VV3AB153J 15k 1W M-Ox.
R887 VRD-RM2HD272JY 2.7k 1/2W Carbon
R888 VRD-RA2BE471JY 470 1/8W Carbon
R892 VRD-RA2BE102JY 1k 1/8W Carbon
R893 VRD-RA2BE102JY 1k 1/8W Carbon
R894 VRD-RA2BE102JY 1k 1/8W Carbon
R898 VRD-RA2BE471JY 470 1/8W Carbon
R899 VRD-RA2BE471JY 470 1/8W Carbon

03.C14-RM50(R)_E_p32-end 02.12.5, 14:4337

P851 QPLGN0661CEZZ Plug, 6-pin(H)

MISCELLANEOUS PARTS

P882 QPLGN0561CEZZ Plug, 5-pin(K)
SC881 QSOCV0017PEZZ CRT Socket

37

C14-RM50

1-4

1-2

1-3

1-7 1-8

2-1

1-8 1-7

1-5

1 1-1

2

2-2

1-6

FOR REFERENCE ONLY

Ref. No. Part No. Description Ref. No. Part No. Description

PWB-C:DUNTK9989WEV9

HEADPHONE UNIT

RESISTORS

RJ1 VRN-MD2AL000J 0 1/10W M-Film
RJ7 VRN-MD2AL000J 0 1/10W M-Film
RJ8 VRN-MD2AL000J 0 1/10W M-Film
R354 VRN-MD2AL471J 470 1/10W M-Film
R355 VRN-MD2AL471J 470 1/10W M-Film

J351 QJAKJ0101SEZZ Headphone Jack
P351 QPLGN0441CEZZ Plug, 4-pin

[M-Film··· Metal Film]

MISCELLANEOUS PARTS

MISCELLANEOUS PARTS

å

ACC701

QACCZ2008PEZZ AC Cord

AC110~240V, 50/60Hz
QCNW-2377PEZZ Connecting Cord
QCNW-2423PEN1 Connecting Cord
QCNW-2452PEZZ Connecting Cord
QANTR0018PEZZ Rod Antenna
LHLDK0005PE00 AC Cord Holder

CABINET PARTS

1 CCABAA102WEV0 Front Cabinet Ass’y

1-1
1-2 HBDGEA003WJSA “HITACHI” BADGE
1-3 GCOVA0120PESA Cover, for R/C,LED
1-4 JBTN-0318PESE Button, Power (431)
1-5 JBTN-0319PESE

1-6 MSPRC0008PEFW Spring, for Power Button
1-7 VSP9050PB35WA Speaker
1-8 QCNW-2380PEZZ SP Wire

2 CCABBA093WEV0 Rear Cabinet Ass’y

2-1
2-2

Not Available

Not Available
Not Available

(431)
Front Cabinet

Control Button, Picture preset,
Vol-up/down

(431)
Rear Cabinet
Caution Label

(431)

SUPPLIED ACCESSORIES

RRMCGA066WJSA Infraed R/C Unit
QPLGJ0113CEZZ Antenna Plug
TiNS-A351WJZZ Operation Manual

PACKING PARTS

(NOT REPLACEMENT ITEM)

SPAKCA349WJZZ Packing Case
SPAKX2724PEZZ Buffer Material
SSAKA0031PEZZ Polyethylene Bag

CABINET PARTS LOCATION

03.C14-RM50(R)_E_p32-end 02.12.5, 14:4338

38

C14-RM50

03.C14-RM50(R)_E_p32-end 02.12.5, 14:4339