Hitachi 57T500A User Manual

Download

Page 1

PROJECTION COLOR TV

57T500 57X500 65T500 65X500

OPERATING GUIDE

IMPORTANT SAFETY INSTRUCTIONS 2-3

FIRST TIME USE 4-22

THE REMOTE CONTROL

ON-SCREEN DISPLAY

USEFUL INFORMATION INDEX 72-78

45-71

23-44

Setup

Locks

Aspect

Audio

Video

Move

SEL

Sel

Ch. Manager

As an ENERGY STAR®Partner, Hitachi, Ltd. has determined that this product meets the E

NERGY STAR

guidelines for energy efficiency.

57T500A 65T500A

Page 2

IMPORTANT

SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION

Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this

section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI television.

Please fill out your warranty card and mail it to HIT ACHI. This will enable HITACHI to notify you promptly in the improbable event that a safety problem should be discovered in your product model.

Follow all warnings and instructions marked on this television.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS TELEVISION TO RAIN OR MOISTURE.

NOTE: • There are no user serviceable parts inside the television.

• Model and serial numbers are indicated on back side of the television.

POWER SOURCE

THIS

TELEVISION

IS DESIGNED TO OPERATE ON 120 VOLTS 60Hz, AC CURRENT. INSERT THE

POWER CORD INTO A 120 VOLT 60Hz OUTLET.

TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TELEVISION’S (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NEVER CONNECT THE

TELEVISION

TO 50Hz, DIRECT CURRENT, OR ANYTHING OTHER THAN THE

SPECIFIED VOLTAGE.

CAUTION: Never remove the back cover of the television as this can expose you to very high voltages and other haz-

ards. If the television does not operate properly, unplug the television and call your authorized dealer or service center.

NOTE: This television receiver will display television closed captioning, ( or ), in accordance with

paragraph 15.119 of the FCC rules.

CAUTION:

Adjust only those controls that are covered in the instructions, as improper changes or modifications not expressly approved by HITACHI could void the user’s authority to operate the television.

MODIFICATIONS:

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hitachi America, Ltd. Home Electronics Division may void the user’s authority to operate the equipment.

Page 3

IMPORTANT

Read before operating equipment

Follow all warnings and instructions marked on this television.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use the attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Televisions are designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to overturn resulting in product damage and/or personal injury.

16.Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.

17.An outdoor antenna should not be located in the vicinity of overhead power lines or other electrical circuits.

18.If an outside antenna is connected to the receiver be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding for the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

Note to the CATV system installer: This reminder is provided to call the CA TV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUNDING CONDUCTORS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250 PART H)

NEC NATIONAL ELECTRICAL CODE

ELECTRIC SERVICE EQUIPMENT

GROUND CLAMP

Do not place any objects on the top of the television which may fall or cause a child to climb to retrieve the objects.

Disposal of this product may require specific instructions pertaining to your resident state. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org.

PUBLIC VIEWING OF COPYRIGHTED MATERIAL

Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require prior authorization from the broadcaster or owner of the video program material.

Projection TV’s are heavy and can mark or damage floor surfaces (especially wood flooring) if moved improperly. Do not slide or force TV into position. Always roll TV allowing casters at bottom of unit to help steer and position the TV.

PREVENTION OF SCREEN BURN

This Wide Screen TV is designed to display wide screen pictures. Images should be viewed mostly in wide screen format or zoomed to fill the screen with moving pictures. Use of side panels, top and bottom panels of standard picture formats should only be 15% of your total viewing time to prevent uneven aging of the phosphors. Phosphors in the lighted area of the picture will age more rapidly than the gray areas. Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed (non-moving) patterns can cause permanent damage to television receivers. Such “SCREEN BURNS” constitute misuse and are NOT

COVERED by your HITACHI Factory Warranty.

Page 4

ACCESSORIES

1. Simple Remote Control Unit CLU-120S (Part No. HL01861).

2. Remote Control Unit CLU-5725TSI (Part No. HL01825).

3. Two “AA” size, 1.5V batteries (For Remote Control Unit).

4. Two “AAA” size, 1.5V batteries (for Simple Remote Control Unit).

5. Two IR Mouse Cables (Part No. EY01641).

REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT

1. Open the battery cover of the remote control by pushing the notched part of the cover with your fingers and pulling the cover off.

2. Insert two new “AA” size batteries for the remote control, and two new “AAA” size batteries for the simple remote control. When replacing old batteries, push them towards the springs and lift them out.

3. Match the batteries to the (+) and (-) marks in the battery compartment.

4. Replace the cover.

BOTTOM VIEW

Lift up on tab to remove back cover.

(Remote Control)

BOTTOM VIEW

(Simple Remote Control)

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace with the same or equivalent type.

Check to make sure you have the following accessories before disposing of the packing material.

CLU-120S 1.

CLU-5725TSI 2.

POWER

VCR

CBL

DVD

INFOSLEEP

A/V NET

EXIT

CHVOL

MUTE

PIP SURF

SWAP

FREEZE

PIP MODE

PIP ACCESS

DAY/NIGHT

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

LAST CH

VID 2

VID 3

VID 4

VID 5

PVR

AMP

VIRTUAL HD

SIMPLE REMOTE

CONTROL

REMOTE CONTROL

BATTERIES

(“AA”)

IR MOUSE

CABLE

BATTERIES

(“AAA”)

FIRST TIME USE

A/V NET

CH +

SELECT

VOL -

MUTE

CH -

POWER

ANT

EXIT

FAV CH

VOL +

Page 5

HOW TO SET UP YOUR NEW HITACHI PROJECTION TV

CAUTION: Magnetic fields, such as those of external speakers, may cause the picture to distort if they are placed too

close to the television. Move the magnetic field source away from the television until there is no picture distortion.

ANTENNA

Unless your TV is connected to a cable TV system or to a centralized antenna system, a good outdoor TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient.

LOCATION

Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.

VIEWING

The major benefit of the HITACHI Projection Television is its large viewing screen. To see this large screen at its best, test various locations in the room to find the optimum spot for viewing.

The best picture is seen by sitting directly in front of the TV and about 10 to 18 feet from the screen. Picture brightness decreases as the viewer moves to the left and right of the receiver.

During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the TV can be located in a different section of the room.

If the TV’s audio output will be connected to a Hi-Fi system’s external speakers, the best audio performance will be obtained by placing the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For best stereo separation, place the external speakers at least four feet from the side of the TV, place the surround speakers to the side or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker placement for best performance.

FIRST TIME USE

Page 6

HOOK-UP CABLES AND CONNECTORS

ANTENNA CONNECTIONS TO REAR JACK PANEL

VHF (75-Ohm) antenna/CATV (Cable TV)

When using a 75-Ohm coaxial cable system, connect the outdoor antenna or CATV coaxial cable to the ANT A (75-Ohm) terminal. If you have a second antenna or cable TV system, connect the coaxial cable to the ANTB terminal.

VHF (300-Ohm) antenna/UHF antenna

When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna leads to screws of the VHF or UHF adapter. Plug the adapter into the antenna terminal on the TV.

When both VHF and UHF antennas are connected

Attach an optional antenna cable mixer to the TV antenna terminal, and connect the cables to the antenna mixer. Consult your dealer or service store for the antenna mixer.

Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output and input connector types required by the various components and the length of each cable.

300-Ohm Twin Lead Connector

This outdoor antenna cable must be connected to an antenna adapter (300-Ohm to 75-Ohm).

Phono Connector

Used on all standard video and audio cables which connect to inputs and outputs located on the television’s rear jack panel and front control panel.

“F” Type 75-Ohm Coaxial Antenna Connector

For connecting RF signals (antenna or cable TV) to the antenna jack on the television.

S-Video (Super Video) Connector

This connector is used on camcorders, VCRs and laserdisc players with an S-Video feature in place of the standard video cable to produce a high quality picture.

IR Mouse Cable (Provided)

Connect the IR Mouse Cable to the IR BLASTER output of your TV when using the A/V Network feature. You must place the IR mouse transmitter in front of the IR sensor of your external components. This connection allows your TV to control your external components without using your external component’s remote control.

Digital Visual Interface (DVI) Connection Cable

This cable is used to connect external devices with DVIHDTV output capability.

FIRST TIME USE

To outdoor antenna or CATV cable

From UHF antenna

To second antenna or cable system

To outdoor VHF or UHF antenna

ANT A/ANT B

Antenna Mixer

From outdoo antenna or CATV System

Page 7

FRONT PANEL CONTROLS

FIRST TIME USE

POWER



INPUT 5

S-VIDEO

VIDEO

AUDIO

L/MONO

EXIT

INPUT

SELECT

MAGIC FOCUS

VOL- VOL+ CH- CH+















POWER



CURSOR

PHOTO MC

PULL





 MENU/SELECT button

This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode.

 INPUT/EXIT button

Press this button to select the current antenna source, VIDEO: 1, 2, 3, 4, 5 or alternate antenna source. Your selection is shown in the top right corner of the screen. This button also serves as the EXIT button when in MENU mode.

 CHANNEL selector

Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as the cursor down () and up () buttons when in MENU mode.

 VOLUME level

Press these buttons for your desired sound level. The volume level will be displayed on the TV screen. These buttons also serve as the cursor left () and right () buttons when in MENU mode. When the TV power is turned OFF at a volume level 31 or greater, the volume level will default to 30 when the TV is turned ON. However, if it is set to a level 30 or less, the volume level will be at the level it was set when the TV is turned ON.

 POWER button

Press this button to turn the TV on or off.

 MAGIC FOCUS

Use this button to automatically adjust your picture quality to optimum performance (see page 64).

 FRONT INPUT JACKS (INPUT 5)

Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantly view your favorite show or new recording. Press the INPUT/EXIT button on the front control panel until VIDEO: 5 appears in the top right corner of the TV screen. If you have mono sound, insert the audio cable into the left audio jack.

 IR RECEIVER / LEARNING AV NET sensor

The screen area acts as the IR receiver (remote sensor) and the LEARNING AV NET sensor of the TV. When using the remote control, point it towards the screen for best response.

 PHOTO MC

Insert Photo memory card to view your digital still pictures (see page 27).

 PHOTO MC LED Light Indicator

Shows the status of the memory card (see page 27).

NOTES: Your remote control does not have an INPUT button. To change to video inputs, press VID1~VID5 buttons depending

on your choice (see page 33).

Page 8

FRONT PANEL JACKS AND CONNECTORS

The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples:

NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture

may be abnormal.

2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable.

3. If you have a mono VCR, insert the audio cable into the left audio jack of your TV.

FIRST TIME USE

INPUT 5

S-VIDEO

VIDEO

AUDIO

L/MONO

MAGIC FOCUS

INPUT 5

S-VIDEO

VIDEO

AUDIO

L/MONO

MAGIC FOCUS

Page 9

REAR PANEL JACKS

 Antenna Input/Output

The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANTA and ANT B. ANT A input can be displayed as a main picture or sub-picture. ANT B can only be displayed as a main picture. (ANT B cannot be displayed as a sub-picture.) The antenna output labeled “TO CONVERTER” allows the ANT A connection to pass directly to a different source such as a cable box, only when ANT B is displayed as a main picture.

 Audio/Video Inputs 1, 2, 3 and 4

The VID1~VID4 buttons will select each video source each time they are pressed. Use the audio and video inputs to connect external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (if you have mono sound, insert the audio cable into the left audio jack.)

 MONITOR OUT

These jacks provide fixed audio and video signals which are used for recording. Use the S-VIDEO Output for high quality video output.

 AUDIO TO HI-FI Output

These jacks provide variable audio output to a separate stereo amplifier. With this connection, the audio to the stereo can be controlled by the television’s main volume.

 CENTER IN (Input)

These jacks are for center signals such as Dolby. This feature allows the TV speakers to be used as a center speaker. The TV must be set as a center channel by selecting “TV as Center” on the Internal Speakers Settings of the Audio Menu (see page 51).

 S-VIDEO Inputs 3 and 4

Inputs 3 and 4 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability.

NOTE: You may use VIDEO or S-VIDEO inputs to connect to INPUT 3 and 4, but only one of these inputs may be used at a

time.

NOTE: S-VIDEO Output may be used for recording, only when the input is of S-VIDEO type.

FIRST TIME USE

Models: 57T500 and 65T500

Models: 57X500 and 65X500



IR BLASTER



ANT A

TO CONVERTER

ANT B

AUDIO TO HI-FI

CENTER





INPUT 1

INPUT 2

INPUT 3

INPUT 4



MONITOR

OUT



AUDIO

(MONO)/L

(MONO)/L VIDEO

L VIDEO

AUDIO

Y/VIDEO



DVI-HDTV

S-VIDEO







IR BLASTER

ANT A

TO CONVERTER

ANT B

AUDIO TO HI-FI

CENTER





INPUT 1

INPUT 2

INPUT 3

INPUT 4



MONITOR

OUT



AUDIO

(MONO)/L

AUDIO

(MONO)/L

AUDIO

(MONO)/L VIDEO

LVIDEO



DVI-HDTV DVI-HDTV

Y/VIDEO

S-VIDEO







Page 10

REAR PANEL JACKS

 Component: Y-P

BPR

Inputs

Inputs 1 and 2 provide Y-P

BPR

jacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may

use composite video signal for INPUT:2.

NOTES: 1. Do not connect composite VIDEO and S-VIDEO to Input 3, 4 or 5 at the same time. S-VIDEO has priority

over VIDEO input.

Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PBinput and the components R-Y output to the TV’s PRinput.

3. Your component outputs may be labeled Y-CBCR. In this case, connect the component CBoutput to the TV’s PBinput and the component CRoutput to the TV’s PRinput.

4. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs (see page 48).

5. To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPRjacks.

6. Input 2 (Y/VIDEO) can be used for composite video and component video input.

 IR Blaster

This jack provides IR output to your external components (VCR, Cable box, DVD player, etc.). With this connection, your external components can automatically be controlled by the AV net feature. This connection will allow you to control the external components with your television’s remote control (see page 20).

 DVI-HDTV Input (INPUT 1)

Use this DVI-HDTV Input for your external devices with DVI-HDTV output such as a Set-Top-Box, high-band DTV decoders, DVD players and D-VHS with Digital Content Protection.

 DVI-HDTV Input (INPUT 2)

This input is an extra DVI-HDTV Input for any additional external devices.

NOTES: 1. Only DTV format such as 1080i, 720p, 480i and 480p are available for DVI-HDTV input.

2. The DVI-HDTV input is NOT compatible when used with a DVD player from a personal computer.

3. When connecting a Set-Top-Box with a copy-protect digital out terminal, a high definition picture can be displayed on the screen in its digital form.

FIRST TIME USE

Page 11

REAR PANEL CONNECTIONS

NOTE: 1.

Connect only 1 component to each input jack.

2. Follow connections that pertain to your personal entertainment system.

3. Composite video signal can be input to Input2~Input5.

4. Cables are optional except when noted as provided.

TYPICAL FULL-FEATURE SETUP

Models: 57T500 and 65T500

CENTER

DVI-HDTV

Outside antenna or cable TV coaxial cable

2-Way signal splitter

Stereo System Amplifier

INPUT

Laserdisc player, VCR, camcorder, etc.

HDTV Set-Top Box

DVD Player

Cable TV Box

INPUT

OUTPUT

VCR #1

ANT IN

OUTPUT

S-VIDEO

VLR

(Provided)

D-VHS

ANT A

TO CONVERTER

ANT B

(MONO)/L

IR BLASTER

AUDIO TO HI-FI

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

L VIDEO

INPUT 1

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

DIGITAL OUTPUT

OUTPUT

B/CBPR/CR

L R

VCR #2

V L R

OUTPUT

S-VIDEO

V L R

INPUT

S-VIDEO

OUTPUT

Y P

L R

CONNECT TO IR BLASTER

AUDIO

IR Sensor

FIRST TIME USE

Page 12

FIRST TIME USE

REAR PANEL CONNECTIONS

NOTE: 1.

Connect only 1 component to each input jack.

2. Follow connections that pertain to your personal entertainment system.

3. Composite video signal can be input to Input2~Input5.

4. Cables are optional except when noted as provided.

TYPICAL FULL-FEATURE SETUP

Models: 57X500 and 65X500

CENTER

DVI-HDTV DVI-HDTV

Outside antenna or cable TV coaxial cable

2-Way signal splitter

Stereo System Amplifier

INPUT

Laserdisc player, VCR, camcorder, etc.

HDTV Set-Top Box

DVD Player

Cable TV Box

INPUT

OUTPUT

VCR #1

ANT IN

OUTPUT

S-VIDEO

VLR

(Provided)

D-VHS

DIGITAL OUTPUT

OUTPUT

ANT A

TO CONVERTER

ANT B

(MONO)/L

IR BLASTER

AUDIO TO HI-FI

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

L VIDEO

INPUT 1

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

OUTPUT

B/CBPR/CR

L R

VCR #2

V L R

OUTPUT

S-VIDEO

V L R

INPUT

S-VIDEO

OUTPUT

Y P

L R

CONNECT TO IR BLASTER

IR Sensor

AUDIO

OUTPUT

Page 13

TIPS ON REAR PANEL CONNECTIONS

FIRST TIME USE

• S-VIDEO connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature.

• If your device has only one audio output (mono sound), connect it to the left audio jack on the television.

• Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.

•Asingle VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output (INPUT: 3 in the example on page 11 or page 12). Refer to your VCR operating guide for more information on line input-output connections.

•You may use VIDEO or S-VIDEO inputs to connect to Input 3, Input 4 or Input 5, but only one of these may be used at a time.

• Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack.

• COMPONENT : Y-PBPR (Input 1 & 2) connections are provided for high performance components, such as DVD players and settop-boxes. Use these connections in place of the standard video connection if your device has this feature. Input 2 accepts both composite and component video signals.

•Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PBinput and the components R-Y output to the TV’s PRinput.

•Your component outputs may be labeled Y-CBCR. In this case, connect the components CBoutput to the TV’s PBinput and the components CRoutput to the TV’s PRinput.

•You may use composite video signal for Input 2~Input 5.

• It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPRinputs (see page 48).

•To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the

Y-PBP

jacks.

• When using a DVI input from a Set-Top-Box, it is recommended to use a 1080i or 720p input signal.

Page 14

FIRST TIME USE

CONNECTING EXTERNAL AUDIO DEVICES

To control the audio level of an external audio amplifier with the remote control, connect the system as shown below.

NOTE: 1. To prevent damage to the speaker and distorted sound, set the volume control of the audio amplifier lower and adjust

the sound using the remote control of the TV set.

2. See page 51 for AUDIO Settings.

REAR PANEL OF TELEVISION

DVI-HDTV

DVI-HDTV DVI-HDTV

Stereo System Amplifier

INPUT

ANT A

TO CONVERTER

ANT B

(MONO)/L

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

LVIDEO

INPUT 1

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

Stereo System Amplifier

INPUT

ANT A

TO CONVERTER

ANT B

(MONO)/L

IR BLASTER

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

LVIDEO

INPUT 1

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

IR BLASTER

AUDIO

CENTER

AUDIO TO HI-FI

CENTER

AUDIO TO HI-FI

The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs.

The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your particular assortment of components and features. For best performance, video and audio cables should be made from coaxial shielded wire.

Before Operating External Video Source

The input mode is changed every time the VID1~VID5 button is pressed as shown below. Connect an external source to the INPUT terminal, then press the VID1~VID5 button as necessary to view the input source (see page 33).

(ANTENNA)

(INPUT)

VID1

ANT

Ant A

BPR:1

VID1

NOTE: When the TV is set to VIDEO and a video signal is not received from the VIDEO INPUT JACK on the back panel of the

TV (i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF), the set will appear to be OFF.

CONNECTING EXTERNAL VIDEO SOURCES

Models: 57T500

65T500

Models: 57X500

65X500

INPUT MODE SELECTION ORDER

Page 15

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A MONAURAL AUDIO SOURCE TO INPUT2~INPUT5

1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below.

2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.

3. Press the VID2~VID5 button to view the program from the VCR or the laserdisc player. The VIDEO label disappears automatically after approximately four seconds.

4. Press the ANT button to return to the previous channel.

FIRST TIME USE

Models: 57T500

65T500

Models: 57X500

65X500

IR BLASTER

ANT A

TO CONVERTER

ANT B

AUDIO TO HI-FI

CENTER

DVI-HDTV

(MONO)/L

(MONO)/L VIDEO

AUDIO

VIDEO

Y/VIDEO

S-VIDEO

INPUT 1

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

IR BLASTER

ANT A

TO CONVERTER

ANT B

AUDIO TO HI-FI

CENTER

DVI-HDTV DVI-HDTV

(MONO)/L

(MONO)/L VIDEO

LVIDEO

AUDIO

Y/VIDEO

AUDIO

S-VIDEO

INPUT 1

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

Audio Video

OUTPUT

VCR

Audio Video

OUTPUT

VCR

Page 16

FIRST TIME USE

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A STEREO SOURCE TO INPUT2~INPUT5

1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below.

2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

4. Press the VID2~VID5 button to view the program from the VCR or laserdisc player. The VIDEO label disappears automatically after approximately four seconds.

5. Press the ANT button to return to the previous channel.

NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output. (INPUT: 1 in example on page 11 or page 12) Refer to your VCR operating guide for more information on line input-output connections.

DVI-HDTV

CENTER

DVI-HDTV DVI-HDTV

CENTER

ANT A

TO CONVERTER

ANT B

(MONO)/L

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

VIDEO

INPUT 1

INPUT 2

INPUT 3

MONITOR

OUT

ANT A

TO CONVERTER

ANT B

(MONO)/L

IR BLASTER

AUDIO TO HI-FI

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

L VIDEO

INPUT 1

INPUT 2

INPUT 3

MONITOR

OUT

IR BLASTER

AUDIO TO HI-FI

AUDIO

VCR

OUTPUT

RLV

VCR

OUTPUT

RLV

(MONO)/L VIDEO

INPUT 4

(MONO)/L VIDEO

INPUT 4

Models: 57T500

65T500

Models: 57X500

65X500

Page 17

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING AN S-VIDEO SOURCE TO INPUT 3, 4 AND 5

1. Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV set below.

2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

4. Press the VID3~VID5 button to view the program from the VCR or laserdisc player. The VIDEO label disappears automatically after approximately four seconds.

5. Press the ANT button to return to the previous channel.

NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

FIRST TIME USE

Models: 57T500

65T500

Models: 57X500

65X500

ANT A

TO CONVERTER

ANT B

AUDIO TO HI-FI

CENTER

IR BLASTER

INPUT 1

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

(MONO)/L

(MONO)/L VIDEO

(MONO)/L

AUDIO

OUTPUT

RLV

VCR

AUDIO

VIDEO

Y/VIDEO

DVI-HDTV

S-VIDEO

ANT A

TO CONVERTER

ANT B

AUDIO TO HI-FI

CENTER

IR BLASTER

INPUT 1

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

(MONO)/L

AUDIO

(MONO)/L

AUDIO

(MONO)/L VIDEO

L VIDEO

AUDIO

OUTPUT

RLV

VCR

DVI-HDTV DVI-HDTV

Y/VIDEO

S-VIDEO

Page 18

FIRST TIME USE

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A COMPONENT SOURCE WITH DVI-HDTV CAPABILITY TO INPUT 1 OR INPUT 2 (Models: 57/65X500)

1. Connect the DVI connection cable from the output of the HDTV set top box or DVD player to the DVI-HDTV input as shown on the TV set below.

2. Connect the cable from the AUDIO OUT R of the HDTV set top box or DVD player to the INPUT (AUDIO/R) jack.

3. Connect the cable from the AUDIO OUT L of the HDTV set top box or DVD player to the INPUT (AUDIO/L) jack.

4. Press the VID1 or VID2 (Models: 57/65X500) button to view the program from the HDTV set top box or DVD player. The VIDEO label disappears automatically after approximately four seconds.

5. Press the ANT button to return to the previous channel.

CENTER

DVI-HDTV DVI-HDTV

DVI-HDTV

CENTER

ANT A

TO CONVERTER

ANT B

(MONO)/L

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

VIDEO

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

ANT A

TO CONVERTER

ANT B

(MONO)/L

IR BLASTER

AUDIO TO HI-FI

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

L VIDEO

INPUT 1

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

DIGITAL

OUTPUT CAPABILITY

DIGITAL OUTPUT

OUTPUT

DIGITAL

OUTPUT CAPABILITY

DIGITAL OUTPUT

OUTPUT

INPUT 1

IR BLASTER

AUDIO TO HI-FI

AUDIO

DIGITAL

OUTPUT CAPABILITY

DIGITAL OUTPUT

OUTPUT

AUDIO

Models: 57T500

65T500

Models: 57X500

65X500

NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. The DVI-HDTV input on INPUT 1 or INPUT 2 (Models: 57/65X500) contains the copy protection system called Highbandwidth Digital Content Protection (HDCP). HDCP is a cryptographic system that encrypts video signals when using DVI connections to prevent illegal copying of video contents.

3. DVI is not a “NETWORK” technology. It establishes a one-way point-to-point connection for delivery of uncompressed video to a display.

4. The connected digital output device controls the DVI interface so proper set-up of device user settings determines final video appearance.

Page 19

FIRST TIME USE

CONNECTING A COMPONENT SOURCE TO INPUT 1 OR 2: Y-PBPR.

1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set below.

2. Connect the cable from the CB/PBOUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB)jack.

3. Connect the cable from the CR/PROUT or R-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PR) jack.

4. Connect the cable from the AUDIO OUT R of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/R) jack.

5. Connect the cable from the AUDIO OUT L of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/L) jack.

6. Press the VID1~VID2 button, to view the program from the Laserdisc/DVD player or HDTV set top box. The VIDEO label disappears automatically after approximately four seconds.

7. Press the ANT button to return to the previous channel.

NOTE: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. See page 13 for tips on REAR PANELCONNECTIONS.

DVI-HDTV

CENTER

DVI-HDTV DVI-HDTV

CENTER

AUDIO

ANT A

TO CONVERTER

ANT B

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

VIDEO

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

ANT A

TO CONVERTER

ANT B

IR BLASTER

AUDIO TO HI-FI

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

L VIDEO

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

DVD Player

OUTPUT

RPB

L R

DVD Player

OUTPUT

RPB

L R

AUDIO

(MONO)/L

INPUT 1

IR BLASTER

AUDIO TO HI-FI

(MONO)/L

INPUT 1

Models: 57T500

65T500

Models: 57X500

65X500

Page 20

CONNECTING AV NETWORK

Your Hitachi Television is equipped with an AV Network feature. This feature helps to control your external Audio/Video equipment (VCR, Set Top Box, DVD, etc.). Once this is setup, it allows your IR Mouse connector to control your equipment using your Hitachi TV Remote Control. You can use your Hitachi remote control to control the Audio/Video equipment command without the equipment’s remote control.

The Television rear panel has 2 IR BLASTER jacks. Each IR Mouse cable can connect up to 2 external Audio/Video components. Therefore, you can connect the Television with up to four components. Please see the following example of an AV Network setup between your Hitachi Television and external Audio/Video equipment (VCR and DVD Player).

CONNECTING EXTERNAL AUDIO/VIDEO COMPONENTS TO IR BLASTER FOR AV NETWORK

1. Connect your external Audio/Video components to the Rear Panel jacks as shown on pages 15~19.

2. Connect the IR Mouse cable to the IR BLASTER input of the Television’s rear panel.

3. Place the IR mouse in front of the infrared sensor of the external components you wish to control.

NOTES: 1. The Rear Panel has two IR BLASTER inputs which can control up to a total of four external components.

2. The IR Mouse must be placed in front of the external components IR sensor for the AV Network to work.

3. The correct codes must be entered for each of the Audio/Video components for the AV Network to function properly (see page 22).

CENTER

DVI-HDTV DVI-HDTV

CENTER

ANT A

TO CONVERTER

ANT B

IR BLASTER

AUDIO TO HI-FI

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

LVIDEO

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

AUDIO

INPUT 1

AUDIO

(MONO)/L

DVI-HDTV

DVD Player

IR Sensor

IR Mouse

VCR

R L V

OUTPUT

IR Sensor

OUTPUT

R/CRPB/CB

L R

ANT A

TO CONVERTER

ANT B

AUDIO TO HI-FI

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

L VIDEO

INPUT 2

INPUT 4

MONITOR

OUT

IR Mouse

AUDIO

DVD Player

IR Sensor

IR Mouse

VCR

R L V

OUTPUT

IR Sensor

OUTPUT

R/CRPB/CB

L R

IR Mouse

(MONO)/L

INPUT 1

(MONO)/L VIDEO

INPUT 3

IR BLASTER

4. Press the A/V NET button on the remote control. Use THUMB STICK  or  to highlight the component you wish to set up. Use THUMB STICK  to enter component’s “SOFT KEY” control button. The AV Network Setup Wizard will automatically start upon the very first use. You can access the Setup Menu Wizard again in the future by pressing the INFO button.

Memory Card

Cable Box

VCR

DVD

Move

POWER MENU MORE

Models: 57T500

65T500

Models: 57X500

65X500

FIRST TIME USE

Page 21

AV NETWORK SETUP WIZARD

There are six steps in the setup procedure (DVD setup example below).

5. Follow the steps below to setup your AV network (See page 22 for AV Network Codes).

6. Enter “9999” to uninstall the equipment from your AV Network.

7. See Remote Control AV NET button usage on page 26. NOTES: 1. If your equipment cannot be operated after performing the above procedures, your equipment code has not been pre-

coded into the AV Net.

2. In the unlikely event that your equipment receiver cannot be operated after performing the above procedures, please consult your equipment receiver operating guide.

HITACHI AV NET SET UP

Proper Code Entered

from page 22.

Memory Card

Cable Box

VCR

DVD

Move

POWER MENU MORE

INFO

Device Setting

DVD

Device Code - - - -

(Enter code “9999” to uninstall)

Video Input No Connection Audio Input No Connection

Transmission Test POWER PLAY CH UP BACK OK EXIT

HITACHI AV NET SET UP

DVD

Device Code 0 6 7 2

(Enter code “9999” to uninstall)

Video Input No Connection Audio Input No Connection

Transmission Test POWER PLAY CH UP BACK OK EXIT

Congratulations

Your DVD is now

connected to your AV network.

HITACHI AV NET SETTING LIST

Device Code Video Audio DVD 0672 INPUT 1 Using TV VCR ---- Not Setup Not Setup CBL ---- Not Setup Not Setup STB ---- Not Setup Not Setup PVR ---- Not Setup Not Setup AVR ---- Not Setup Not Setup Custom ---- Not Setup Not Setup

EXIT

HITACHI AV NET SET UP

DVD Device Code 0 6 7 2

(Enter code “9999” to uninstall)

Video Input Input 1 Audio Input Using TV

Transmission Test POWER PLAY CH UP BACK OK EXIT

Move

SEL Select

Set Input

Memory Card

Cable Box

VCR

DVD

POWER MENU MORE

Move

INFO

Device Setting

HITACHI AV NET SET UP

DVD Device Code 0 6 7 2

(Enter code “9999” to uninstall)

Video Input Input 1 Audio Input No Connection

Transmission Test POWER PLAY CH UP BACK OK EXIT

Move

SEL Select

Set Input

HITACHI AV NET SET UP

DVD Device Code 0 6 7 2

(Enter code “9999” to uninstall)

Video Input Input 1 Audio Input Using TV

Transmission Test POWER PLAY CH UP BACK OK EXIT

Move

SEL Select

Set Input

HITACHI AV NET SET UP

SEL

Select

Move

0-9

Input

Move

0-9

Input

THUMB

STICK

THUMB

STICK

THUMB

STICK

THUMB

STICK

SELECT

THUMB

STICK

SELECT

THUMB

STICK

(x2)

Enter the device (equipment) code listed on page 22.

Use THUMBSTICK  to select the input that the device (equipment) is hooked-up to.

Transmission test for the device to confirm that the proper code was set, by selecting (POWER, PLAY, etc.) soft keys shown. If the device responds to the transmission test soft key, then it is properly set up. Select OK to continue.

FIRST TIME USE

Page 22

FIRST TIME USE

AUDIO/VIDEO NETWORK (A/V NET) CODES

VCR BRAND . . . . . . . . . . . . . . . . . . . . . . . . . . . CODE

Admiral. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0048, 0209

Adventura . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0000

Aiko . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278

Aiwa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0037

Akai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0041

America Action . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278

American High . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035

Asha . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Audiovox . . . . . . . . . . . . . . . . . . . . . . . . . . 0037, 0278

Beaumark. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Bell & Howell . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0104

Broksonic . . . . . . . . . . . . . . . . 0121, 0184, 0002, 0209,

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0479, 1479, 0278

CCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072, 0278

Calix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Canon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035

Carver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0081

Cineral . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278

Citizen . . . . . . . . . . . . . . . . . . . . . . . 0278, 0037, 1278

Colt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

Craig. . . . . . . . . . . . . . . . . . . . 0037, 0072, 0047, 0240

Curtis Mathes. . . . 0035, 0041, 0060, 0162, 0760, 1035

Cybernex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Daewoo . . . . . . . . . . . . . . . . . . . . . . 0278, 1278, 0045

Denon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0042

Dynatech . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Electrohome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Electrophonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Emerex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0032

Emerson . . . . . . . . . . . . . . . . . . . . . 0184, 0002, 0209,

. . . . . . . . . . . . . . . . . . . . . . . . 0121, 0000, 0037, 0043

Fisher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0104, 0047

Fuji . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0033, 0035

Funai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

GE . . . . . . . 0035, 0060, 0240, 0760, 0807, 1035, 1060

Garrard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Go Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0432

GoldStar . . . . . . . . . . . . . . . . . . . . . . 0037, 0038, 1237

Gradiente. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

HI-Q. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0047

Harley Davidson. . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Harman/Kardon . . . . . . . . . . . . . . . . . . . . . 0038, 0081

Harwood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

Hitachi . . . . . . . . . . . . . . . . . . . . . . . 0000, 0041, 0042

Hughes Network Systems. . . . . . . . . . . . . . . . . . . 0042

JVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0067, 0041

Jensen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0041

KEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037, 0278

KLH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

Kenwood. . . . . . . . . . . . . . . . . . . . . . 0041, 0067, 0038

Kodak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035, 0037

LXI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Lloyd's . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Logik . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

MEI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035

MGA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0043, 0240

MGN Technology . . . . . . . . . . . . . . . . . . . . . . . . . 0240

MTC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0240

Magnasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1278

Magnavox . . . . . . . . . . . . . . . . . . . . 0035, 0081, 0563,

. . . . . . . . . . . . . . . . . . . . . . . . 0000, 0039, 0149, 1781

Magnin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Marantz . . . . . . . . . . . . . . . . . . . . . . . . . . . 0081, 0035

Marta . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Matsushita . . . . . . . . . . . . . . . . . . . . 0035, 0162, 0454

Memorex . . . . . . . . . . . . . . . . 0047, 0037, 0104, 0209,

. . . . . . . . . . . . . . . . . . . 0454,0048, 0039, 0240, 0000,

. . . . . . . . . . . . . . . . . . . 0479, 1037, 1162, 1237, 1262

Minolta. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0042

Mitsubishi. . . . . . . . . . . . . . . . . . . . . 0807, 0043, 0067

Motorola. . . . . . . . . . . . . . . . . . . . . . . . . . . 0035, 0048

Multitech. . . . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0072

NEC . . . . . . . . . . . . . . . . . . . . 0038, 0041, 0067, 0104

Nikko . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Noblex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Olympus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035

Optimus . . . . . . . . . . . . . . . . . 1062, 0162, 0037, 0048,

. . . . . . . . . . . . . . 0104, 0432, 0454, 1048, 1162, 1262

Orion . . . . . . . . . . . . . . . 0184, 0209, 0002, 0479, 1479

Panasonic. . . . . . . . . . 1062, 0035, 01625, 0225, 0454,

. . . . . . . . . . . . . . . . . . . . . . . . 0616, 1035, 1162, 1262

Penney. . . . . . . . . . . . . . . . . . 0035, 0037, 0240, 0042,

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0038, 1035, 1237

Pentax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0042

Philco . . . . . . . . . . . . . . . . . . . . . . . . 0035, 0209, 0479

Philips . . . . . . . . . . . . . . 0081, 0035, 0618, 1081, 1181

Pilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Pioneer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0067

Polk Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0081

Profitronic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Proscan . . . . . . . . . . . . . . . . . . . . . . 0060, 0760, 1060

Protec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

Pulsar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0039

Quasar. . . . . . . . . . . . . . 0035, 0162, 0454, 1035, 1162

RCA. . . . . . . . . . . . . . . . . . . . 0060, 0240, 0042, 0149,

. . . . . . . . . . . . . . . . . . . . . . . . 0760, 0807, 1035, 1060

Radio Shack . . . . . . . . . . . . . . . . . . . . . . . . 0000, 1037

Radix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Randex. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Realistic. . . . . . . . 0035, 0037, 0048, 0047, 0000, 0104

ReplayTV . . . . . . . . . . . . . . . . . . . . . . . . . . 0614, 0616

Runco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0039

STS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0042

Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . 0045, 0240

Sanky . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0039, 0048

Sansui . . . . . . . . . 0000, 0067, 0209, 0041, 0479, 1479

Sanyo. . . . . . . . . . . . . . . . . . . . . . . . 0047, 0240, 0104

Scott . . . . . . . . . . . . . . . . . . . . 0184, 0045, 0121, 0043

Sears . . . . . 0035, 0037, 0047, 0000, 0042, 0104, 1237

Semp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0045

Sharp . . . . . . . . . . . . . . . . . . . . . . . . 0048, 0807, 0848

Shintom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

Shogun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Singer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

Sonic Blue . . . . . . . . . . . . . . . . . . . . . . . . . 0614, 0616

Sony. . . . . . 0035, 0032, 0000, 0033, 0636, 1032, 1232

Sylvania. . . . . . . . . . . . . 0035, 0081, 0000, 0043, 1781

Symphonic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

TMK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Tatung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0041

Teac. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0041

Technics. . . . . . . . . . . . . . . . . . . . . . . . . . . 0035, 0162

Teknika. . . . . . . . . . . . . . . . . . . . . . . 0000, 0035, 0037

Thomas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Tivo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0618, 0636

Toshiba. . . . . . . . . . . . . . . . . . . . . . . . 0045, 0043, 845

Totevision. . . . . . . . . . . . . . . . . . . . . . . . . . 0037, 0240

Unitech. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Vector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0045

Vector Research. . . . . . . . . . . . . . . . . . . . . . . . . . 0038

Video Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . 0045

Videomagic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Videosonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Wards. . . . . . . . . . . . . . . . . . . 0060, 0035, 0048, 0047,

. . . . . . . . . 0081, 0240, 0000, 0042, 0072, 0149, 0760

White Westinghouse . . . . . . . . . . . . . 0072, 1278, 0209

XR-1000 . . . . . . . . . . . . . . . . . . . . . . 0072, 0000, 0035

Yamaha . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0038

Zenith. . . . . . . . . . . . . . . . . . . 0039, 0000, 0209, 0033,

. . . . . . . . . . . . . . 0479, 1479, 0033, 0034, 0209, 0479

DVD BRAND . . . . . . . . . . . . . . . . . . . . . . . . . . . CODE

Aiwa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0641

Apex. . . . . . . . . . . . . . . . . . . . 0672, 0717, 0755, 0794,

. . . . . . . . . . . . . . . . . . . . . . . . 0795, 0796, 0797, 0830

Audiologic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0736

B & K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0655, 0662

Blue Parade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0571

Brooksonic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0695

DVD2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0521

Daewoo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0784

Denon . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0490, 0634

Emerson . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0591

Enterprise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0591

Fisher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0670

GE . . . . . . . . . . . . . . . . . . . . . . . . . . 0522, 0717, 0815

GPX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0699, 0769

Go Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0715

Gradiente. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0651

Greenhill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0717

Harman/Kardon . . . . . . . . . . . . . . . . . . . . . 0582, 0702

Hitachi . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0573, 0664

Hiteker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0672

JBL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0702

JVC . . . . . . . . . . . . . . . . . . . . . . . . . 0623, 0558, 0867

KLH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0717

Kenwood. . . . . . . . . . . . . . . . . . . . . . 0490, 0534, 0682

Konka . . . . . . . . . . . . . . . . . . . . . . . . 0711, 0719, 0721

Koss. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0651

Lasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0798

Magnavox. . . . . . . . . . . . . . . . . . . . . . . . . . 0503, 0675

Malata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0782

Marantz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0539

Microsoft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0522

Mintek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0717

Mitsubishi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0521

Nesa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0717

Onkyo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0627, 0503

Oritron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0651

Panasonic. . . . . . . . . . . . . . . . . . . . . 0490, 1362, 0632

Philips. . . . . . . . . . . . . . . . . . . 0503, 0539, 0646, 0854

Pioneer. . . . . . . . . . . . . . . . . . . . . . . 0525, 0571, 0632

Polk Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0539

Princeton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0674

Proscan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0522

RCA . . . . . . . . . . . . . . . . . . . . 0522, 0571, 1022, 0717

Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . 0573, 0820

Sansui . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0695

Sanyo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0670

Sharp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0630

Sherwood. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0633

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0533

Sylvania. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0675

Technics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0490

Techwood. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0692

Theta Digital. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0571

Toshiba. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0503, 0695

Urban Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . 0503

Yamaha . . . . . . . . . . . . . . . . . . . . . . 0490, 0545, 0539

Zenith . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0591, 0503

CABLE BRAND. . . . . . . . . . . . . . . . . . . . . . . . . CODE

ABC . . . . . . . . . . . . . . . . . . . . 0003, 0008, 0014, 0017

Americast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0899

Bell & Howel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0014

Bell South . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0899

Director . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0476

General Instrument . . . . . . . . . 0003, 0476, 0276, 0810

GoldStar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0144

Hamlin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0009, 0273

Jerrold. . . . . . . . . .0476, 0003, 0276, 0012, 0014, 0810

Memorex. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0000

Motorola . . . . . . . . . . . . . . . . . 0476, 1106, 0276, 0810

Pace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0237

Panasonic. . . . . . . . . . . . . . . . . . . . . . . . . . 0107, 0000

Philips . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0305, 0317

Pioneer . . . . . . . . . . . . . . . . . . 0144, 0533, 0877, 1877

Pulsar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Quasar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0000

Regal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0273, 0279

Runco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0000

Samsung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0144

Scientific Atlanta . . . . . . 0877, 0008, 0017, 0477, 1877

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1006

Starcom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0003

Supercable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0276

Tocom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0012

Torx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0003

Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Zenith . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0525, 0899

SATELLITE BRAND (Set-Top-Box). . . . . . . . . . CODE

AlphaStar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0772

Chapparral. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0215

Crossdigital. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1109

DishPro . . . . . . . . . . . . . . . . . . . . . . . . . . . 1005, 0775

Echostar . . . . . . . . . . . . . . . . . . . . . . . . . . . 1005, 0775

Expressvu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0775

GE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0566

GOI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0775

General Instrument. . . . . . . . . . . . . . . . . . . . . . . . 0869

HTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0775

Hitachi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0819

Hughes Network Systems . . . . . . . . . 1142, 0749, 1749

JVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0775

Magnavox. . . . . . . . . . . . . . . . . . . . . . . . . . 0724, 0722

Memorex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0724

Mitsubishi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0749

Motorola. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0869

Next Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0869

Panasonic. . . . . . . . . . . . . . . . . . . . . . . . . . 0247, 0701

Paysat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0724

Philips . . . . . . . . . 1142, 0749, 0724, 1076, 0722, 1749

Proscan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0392

RCA . . . . . . . . . . . . . . . . . . . . 0392, 0566, 0855, 0143

Radioshack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0869

SKY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0856

Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1109

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0639

Star Choice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0869

Toshiba. . . . . . . . . . . . . . . . . . . . . . . 0749, 0790, 1749

Uniden . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0724, 0722

Zenith . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0856, 1856

AMPLIFIER BRAND . . . . . . . . . . . . . . . . . . . . . CODE

Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0406

Bose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0674

Carver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0269

Curtis Mathes . . . . . . . . . . . . . . . . . . . . . . . . . . . .0300

Denon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0160

GE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0078

Harman/Kardon . . . . . . . . . . . . . . . . . . . . . . . . . . .0892

JVC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0331

Left Coast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0892

Linn. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0269

Luxman . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0165

Magnavox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0269

Marantz. . . . . . . . . . . . . . . . . . . . . . . 0269, 0321, 0892

NEC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0264

Nakamichi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0321

Optimus . . . . . . . . . . . . . . . . . . . . . . . . . . . 0395, 0300

Panasonic. . . . . . . . . . . . . . . . . . . . . . . . . . 0308, 0521

Parasound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0246

Philips . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0269, 0892

Pioneer. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0013, 0300

Polk Audio . . . . . . . . . . . . . . . . . . . . . . . . . 0269, 0892

RCA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0300

Realistic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0395

Sansui . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0321

Shure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0264

Sony. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0689, 0220

Soundesign. . . . . . . . . . . . . . . . . . . . . . . . . 0078, 0211

Technics. . . . . . . . . . . . . . . . . . . . . . . . . . . 0308, 0521

Victor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0331

Wards . . . . . . . . . . . . . . . . . . . . . . . . 0013, 0078, 0211

Yamaha . . . . . . . . . . . . . . . . . . . . . . . . . . . 0354, 0133

RECEIVER BRAND (Amplifier). . . . . . . . . . . . . CODE

ADC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0531

Adcom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0616

Aiwa. . . . . . . . . . . . . . . . . . . . 1089, 1405, 0121, 0158,

. . . . . . . . . . . . . . . . . . . . . . . . 0189, 0405, 1321, 1388

Akai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0076, 0224

Alco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1390

Anam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074, 1609

Apex Digital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1257

Arcam. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1120

Audiotronic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1189

Audiovox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1390

Bose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1229

Capetronic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0531

Carver . . . . . . . . . 1089, 1189, 0008, 0042, 0189, 0360

Casio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

Celestion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1264

Clarinette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

Compaq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1136

Curtis Mathes. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0080

Denon . . . . . . . . .1104, 0004, 0273, 0771, 1311, 1360

Emerson . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0424

Fisher . . . . . . . . . . . . . . . . . . . . . . . . 0042, 0219, 0360

GPX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1299

Garrard. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0424, 0463

Glory Horse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1263

Harman/Kardon . . . . . . . . . . . . . . . . . 0891, 0110, 0189

Hewlett Packard . . . . . . . . . . . . . . . . . . . . . . . . . . 1181

Inkel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0062

JBL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0110, 1306

JVC . . . . . . . . . . . . . . . . . . . . . . . . . 0074, 1263, 1374

Kenwood. . . . . . . 1313, 1027, 1570, 1569, 0027, 0042,

. . . . . . . . . 0077, 0186, 0313, 0314, 0569, 1051, 1052

Koss. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0424, 1366

LXI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0181

Lexicon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1076

Linn. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0189

Lloyd's . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

MCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0039, 0346

Magnavox . . . . . . . . . . . . . . . . . . . . 1089, 1189, 0128,

. . . . . . . . . . . . . . . . . . . . . . . . 0189, 0195, 0391, 0531

Marantz . . . . . . . . . . . . . 1089, 1189, 0039, 0128, 0189

Modulaire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

Musicmagic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1089

NAD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0320

NEC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0235

Nakamichi. . . . . . . . . . . . . . . . . . . . . . . . . . 0097, 0347

Onkyo . . . . . . . . . . . . . . 0100, 0135, 0380, 0842, 1298

Optimus . . . . . . . 1023, 0042, 0080, 0177, 0181, 0186,

. . . . . . . . . . . . . . 0219, 0531, 0670, 0738, 0801, 1074

Panasonic . . . . . . . . . . . . . . . . . . . . 1518, 0039, 0309,

. . . . . . . . . . . . . . . . . . . . . . . . 0367, 0518, 1288, 1350

Penney. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

Philips . . . . . . . . . . . . . . . . . . 1089, 1189, 1269, 0189,

. . . . . . . . . . . . . . . . . . . . . . . . 0391, 1120, 1268, 1283

Pioneer. . . . . . . . . . . . . . . . . . 1023, 0014, 0080, 0150,

. . . . . . . . . . . . . . . . . . . 0244, 0531, 0630, 1343, 1384

Polk Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0189

Proscan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1254

Quasar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0039

RCA . . . . . . . . . . 1023, 1254, 0054, 0080, 0346, 0360,

. . . . . . . . . . . . . . 0530, 0531, 1074, 1154, 1390, 1609

Radio Shack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1263

Realistic . . . . . . . . . . . . . . . . . . . . . . 0163, 0181, 0195

Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1295

Sansui. . . . . . . . . . . . . . . . . . . 0189, 1089, 0193, 0346

Sanyo. . . . . . . . . . . . . . . . . . . . . . . . 0219, 0801, 1251

Scott. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0163, 0322

Sharp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0186

Sherwood . . . . . . . . . . . . . . . . 0062, 0491, 0502, 1653

Sony. . . . . . . . . . . . . . . . . . . . 1058, 1258, 1158, 0158,

. . . . . . . . . . . . . . . . . . . 0168, 0474, 1042, 1458, 1758

Soundesign . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0670

Stereophonics . . . . . . . . . . . . . . . . . . . . . . . . . . . 1023

Sunfire . . . . . . . . . . . . . . . . . . 1313, 0313, 0314, 1052

Teac . . . . . . . . . . . . . . . . . . . . . . . . . 0463, 0163, 1074

Technics. . . . . . . . . . . . . . . . . . . . . . 1308, 1309, 1518,

. . . . . . . . . . . . . . . . . . . . . . . . 0039, 0208, 0309, 0518

Thorens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1189

Victor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0074

Wards. . . . . . . . . . . . . . .0014, 0054, 0080, 0158, 0189

Yamaha. . . . . . . . . . . . . . . . . . . . . . . 0176, 0186, 1176

Yorx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

Zenith. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0857

AUDIO BRAND . . . . . . . . . . . . . . . . . . . . . . . . . CODE

Aiwa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0010, 0159

AudioSource. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0351

Cambridge Soundworks . . . . . . . . . . . . . . . . . . . . 0351

Carver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0351

Fisher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0052

Fosgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0259

Harmon/Kardon . . . . . . . . . . . . . . . . . . . . . . . . . . 0477

JBL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0477

JVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0073

KLH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0351

Magnavox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0325

Nikko . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0376

Paramount Pictures . . . . . . . . . . . . . . . . . . 0317, 0351

RCA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0056

SSI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0317

Sansui . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0325

Schneider. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0376

Sony. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0010, 0576

Soundesign . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0376

Yorx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0376

SET TOP BOX BRAND . . . . . . . . . . . . . . . . . . . CODE

Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1120

Pioneer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010

Princeton . . . . . . . . . . . . . . . . . . . . . . . . . . 0113, 0295

Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1190

Sensory Science. . . . . . . . . . . . . . . . . . . . . . . . . . 1126

Sharp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0639

PERSONAL VIDEO RECORDER BRAND . . . . . CODE

Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0616

Philips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0618

ReplayTV . . . . . . . . . . . . . . . . . . . . . . . . . . 0614, 0616

SonicBlue. . . . . . . . . . . . . . . . . . . . . . . . . . 0614, 0616

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0636

Tivo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0618, 0636

Page 23

THE REMOTE CONTROL

In addition to controlling all the functions on your HITACHI Projection TV, the new remote control is designed to operate different types of VCRs, CATV (Cable TV) converters, set-top-box, satellite receiver, DVD players, and other audio/video equipment with one touch. Basic operation keys are grouped together in one area.

To operate your TV, point the remote control at the screen of the TV and press the TV button. The TV button will blink, indicating that the remote will now control your television.

To operate your VCR, point the remote at the remote sensor of the VCR and press the VCR button. The VCR button will blink, indicating that the remote will now control your VCR (see page 37 for instructions on how to program the remote to control your VCR).

To operate your cable box, point the remote at the remote sensor of the cable box and press the CABLE (CBL) button. The CBL button will blink, indicating that the remote will now control your cable box (see page 38 for instructions on how to program the remote to control your cable box).

To operate your set-top-box or satellite receiver point the remote at the remote sensor of the set-top-box and press the SET-TOPBOX (STB) button. The STB button will blink, indicating that the remote will now control your set-top-box. If you have a satellite receiver, use this button to program your satellite receiver (see page 39 for instructions on how to program the remote to control your set-top-box).

To operate your DVD player, point the remote at the remote sensor of the DVD player and press the DVD button. The DVD button will blink, indicating that the remote will now control your DVD player (see page 40 for instruction on how to program the remote to control your DVD player).

To operate your PVR (Personal Video Recorder), point the remote at the remote sensor of the PVR and press the PVR button. The PVR button will blink, indicating that the remote will now control your PVR (see page 41 for instruction on how to program the remote to control your PVR).

To operate additional audio equipment, point the remote at the remote sensor of the component you wish to control and press the CD or AMP button. This button will blink, indicating that the remote will now control the desired component (see page 42 for instructions on how to program the remote to control additional Audio/Video equipment).

 These buttons allow the remote to control your TV, VCR,

cable box, satellite receiver, DVD player, or other Audio/Video equipment depending on which mode is chosen, as explained above.

, LIGHT BUTTON

When you are in a dark room, press the light button  on the remote to light up the buttons shown in  and the source button will blink. The light will stay on for about 8 seconds if the light button is not pressed again. These buttons will not appear to light if the room is too bright.







POWER

VCR

CBL

DVD

INFOSLEEP

A/V NET

EXIT

CHVOL

MUTE

PIP SURF

SWAP

FREEZE

PIP MODE

PIP ACCESS

DAY/NIGHT

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

LAST CH

VID 1

VID

VID 3

VID 5

PVR

AMP

VIRTUAL HD

THE REMOTE CONTROL

Page 24

THE REMOTE CONTROL

HOW TO USE THE REMOTE TO CONTROL YOUR TV

 POWER button

Press this button to turn the TV set on or off when the remote is in TV mode (see page 23 for instructions on how to set the remote control to TV mode).

 TV button

When the TV button is pressed, it will blink, to indicate the remote is in TV mode.

 VCR button

When the VCR button is pressed, it will blink to indicate the remote is in VCR mode (see page 37).

 CABLE (CBL)

When the CABLE button is pressed, it will blink to indicate the remote is in CABLE mode (see page 38).

 SET-TOP-BOX (STB)

When the STB button is pressed, it will blink to indicate the remote is in STB mode (see page 39). If you have a Satellite receiver, use this button to program your Satellite receiver (see page 39).

 DVD button

When the DVD button is pressed, it will blink to indicate the remote is in DVD mode (see page 40).

















 























POWER

VCR

CBL

DVD

INFOSLEEP

A/V NET

EXIT

CHVOL

MUTE

PIP SURF

SWAP

FREEZE

PIP MODE

PIP ACCESS

DAY/NIGHT

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

LAST CH

VID 1

VID 3

VID 4

VID 5

PVR

AMP

VIRTUAL HD



Page 25

THE REMOTE CONTROL

HOW TO USE THE REMOTE TO CONTROL YOUR TV

 C.C. button

Press this button to quickly turn the Closed Caption feature on, off and auto. You can also access this feature on the Setup menu (See page 71).

 PVR (Personal Video Recorder) button

When pressed, this button will blink to indicate the remote is in PVR mode (see page 41).

 CD and AMP buttons

When pressed, each of these buttons will blink to indicate the remote is in Audio mode (see page 42).

 CHANNEL selector buttons

CHANNEL selector buttons are used to select channels, lock access code, etc. Enter one, two, or three numbers to select channels. Enter “0” first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the “1” button, wait until two dashes appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons. Channel selection may also be performed by pressing CH up () or down ().

 SLEEP and (-) DASH button

Press this button to display the sleep timer in the lower left corner of the screen. Every subsequent press of this button will add 15 minutes to this timer, up to a maximum of three hours. Once set, use INFO when you want to view time remaining. If the SLEEP button is pressed while the timer is set, it will reset to the original condition. The DASH (-) button can only be used when the remote control is in Set-Top-Box (STB) mode.

 INFO button

Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second audio program (SAP), the time, CHANNEL ID and if the SLEEP timer is set.

 ANTENNA button

The ANT button will select between Antenna A and Antenna B each time the button is pressed.

NOTE: The TV may not receive some channels if you are not in the correct ANTENNA/CABLE mode (see page 54).

Main Picture Source

Time

Wide

Mode

Day/Night

Mode

Closed

Captioning

Off Timer

Sleep Timer

3:32 PM

Ant A 22

Stereo

1080i Format

Day 4:3 Expanded HD 1080i Off 0:00 AM -:--

View

Zzzz

Audio Broadcast Broadcast Rating Signal Format

Virtual HD

When an S-VIDEO Input is connected to VIDEO: 3.

When a COMPONENT VIDEO: Y-PBPRInput is connected to VIDEO: 1.

3:32 PM

S-IN: 3

VID 3

3:32 PM

YPBPR: 1

VID: 1

3:32 PM

Ant B 22

Stereo

3:32 PM

Ant A 15

Stereo

ANT

Page 26

HOW TO USE THE REMOTE TO

CONTROL YOUR TV

THE REMOTE CONTROL

 AV NET button

Press this button to access the Audio/Video network (AV Net) menu. The AV Net allows the user to control external components with the Projection TV’s remote control. When you press the AV NET button, the following window will pop up within the Display Monitor screen. The window will disappear after 30 seconds if you don’t press any buttons.

The AV Net Setup Wizard will automatically start upon the very first use. (see page 20-22). THUMBSTICK  or  to highlight the equipment you wish to control or setup and then press THUMBSTICK . Use THUMBSTICK , , ,  to navigate and SELECT to select button. The command on the button is passed through the IR mouse and onto the AUDIO/VIDEO equipment. These on-screen buttons are called “Soft Keys”.

Customize your Audio/Video equipment list and soft keys by selecting the “Custom” icon and following the instructions of the AV NET learning wizard (see page 30).

This window shows the available Audio/Video equipment soft keys. The equipment list will scroll up or down.

Photo MC

Cable Box

VCR

DVD

Move

POWER MENU MORE..

THUMB

STICK

SELECT

THUMB

STICK

INFO

Device Setting

AV Receiver

PV Recorder

VCR

DVD

Move

POWER MENU MORE

SEL

123

456

MORE..

Photo MC

Cable Box

VCR

DVD

Move

POWER

INFO

Device Setting

CH CH





TV/VCR

MORE..

AV Receiver

PV Recorder

VCR

DVD

Move

POWER

SEL

CH CH



TV/VCR

123

456

THUMB

STICK

SELECT

MORE..

THUMB

STICK

Photo MC

Cable Box

VCR

DVD

Move

INFO

Device Setting

THUMB

STICK

Photo MC

Cable Box

VCR

DVD

Move

THUMB

STICK

ACCESS

THUMB

STICK

SELECT

Move

ORIGINAL MENU

OF EQUIPMENT

AV NET

Return

THUMB

STICK

SELECT

Move

ORIGINAL MENU

OF EQUIPMENT

AV NET

Return

See Page 29

See Page 27

POWER

CH CH



INFO

123

456

LAST CH

THUMB

STICK

NOTE: To access the cursor function of a specific equipment (Ex. DVD, VCR), select the “MENU” soft key on OSD, and press

the MENU button of the Projection TV remote control. Then THUMBSTICK and EXITbutton of the Projection TV remote control is available to control the cursor of the equipment.

Page 27

HOW TO USE THE REMOTE TO CONTROL YOUR TV

THE REMOTE CONTROL

Photo MC

The Photo MC feature is useful for viewing digital still pictures from your digital camera using a memory card and displaying them on the TV screen. Insert Photo MC (memory card) to be viewed to a PC Card adapter. Insert the loaded PC Card adapter to the Photo MC slot of the control panel in the front of the TV.

Press THUMBSTICK  to view the digital photos in THUMBNAIL view. Use THUMBSTICK , , ,  to select individual photos. Press SELECT to view and enlarge individual photos. Press SELECT once again to switch enlarged photo back to THUMBNAIL view. Press MENU to access the PHOTO MC menu. Press THUMBSTICK ,  to highlight menu item. Press SELECT to choose the menu item. Press EXIT to quit menu.

1/10 2/10 3/10 4/10

8/107/106/105/10

9/10 10/10

THUMB

STICK

1/10 2/10 3/10 4/10

8/107/106/105/10

9/10 10/10

No. 7/10 03/04/03 1632x1232

Picture No. Date Resolution

1/10 2/10 3/10 4/10

8/107/106/105/10

9/10 10/10

1/10 2/10 3/10 4/10

8/107/106/105/10

9/10 10/10

Jump

Slideshow Rotate

Please Enter

Picture Number

- - -

1/10 2/10 3/10 4/10

8/107/106/105/10

9/10 10/10

No. 7/10 03/04/03 1632x1232

Picture No. Date Resolution

THUMB

STICK

THUMB

STICK

SELECT

THUMB

STICK

SELECT

THUMB

STICK

SELECT

THUMB

STICK

SELECT

Jump

Photo MC

Cable Box

VCR

DVD

ACCESS

JUMP

Select this menu item to view the chosen picture number.

NOTE: 1. Contrast will decrease automatically if stationary images such as digital still photos are left on the screen for

more than 3 minutes.

2. The maximum number of digital Photos that can be displayed is 500.

LED Light and OSD Indicator

Memory Card Detail Information (OSD and LED)

Accessing LED Blinking Normal LED always On Card not inserted “No Memory Card” FAT32 “Memory Card is not available” Not available format “Memory Card is not available” Abnormal “Memory Card is not available” No File “No File”

Page 28

HOW TO USE THE REMOTE TO

CONTROL YOUR TV

THE REMOTE CONTROL

SLIDESHOW

Select this menu item to start a slideshow of the Photos in the memory card. Time interval selections can be set from 5, 10 and 30 seconds.

ROTATE

Select this menu item to rotate selected photos either clockwise (THUMBSTICK ) and counterclockwise (THUMBSTICK ).

Use THUMBSTICK ,  to highlight Slideshow item. While interval is highlighted, press SELECT to change interval time from 5, 10 and 30 seconds. Each press will change interval time from the three mentioned choices. Press SELECT to stop on a chosen picture of the slideshow. After 30 seconds, the slideshow will resume or press SELECTagain to continue the slideshow. Press EXIT to exit the slideshow.

NOTES: 1. Photo file names modified on a computer should be 8 characters (Ex. ABCD1234.jpg). 1st character: letters;

2nd to 4th: letters or numbers; 5th to 8th: numbers. Photo files should be first placed on a sub directory name with 8 characters (Ex. 123ABCDE). 1st to 3rd: number; 4th to 8th: letters. The sub directory then should be placed on a main directory with a “dcim” file name format.

2. Supported image types are from VGA (640 x 480) up to UXGA (1600 x 1200); JPEG format should conform with DCF Standard (Design rule for Camera File System).

3. This TV set displays only digital pictures from digital cameras which meet DCF Standard. Pictures that were copied, edited or modified on a computer may not be displayed on the TV set.

Jump

1/10 2/10 3/10 4/10

Slideshow

Rotate

8/107/106/105/10

9/10 10/10

1/10

Slideshow

THUMB

STICK

SELECT

THUMB

STICK

SELECT

5 seconds

1/10 2/10 3/10 4/10

Jump

Slideshow

Rotate

9/10 10/10

Start

Interval

5 sec

8/107/106/105/10

2/10

5 seconds.. etc.

Jump

1/10 2/10 3/10 4/10

Slideshow

Rotate

8/107/106/105/10

9/10 10/10

1/10

Rotate

THUMB

STICK

SELECT

THUMB

STICK

THUMB

STICK

1/10

Page 29

HOW TO USE THE REMOTE TO CONTROL YOUR TV

THE REMOTE CONTROL

NOTE: To access the cursor function of a specific equipment (Ex. PV Recorder), select the “MENU” soft key on OSD, and press

the MENU button of the Projection TV remote control. Then THUMBSTICK and EXITbutton of the Projection TV remote control is available to control the cursor of the equipment.

POWER

CH CH

STICK

SOURCE3SOURCE2

SOURCE7



SOURCE4

SOURCE8

AV Receiver

PV Recorder

Set Top Box

Custom

Move

INFO

Device Setting

Audio VOL VOL

Inputs:

SOURCE1

SOURCE6

SOURCE5

THUMB

AV Receiver

PV Recorder

Set Top Box

Custom

Move

AV Receiver

PV Recorder

Set Top Box

Custom

Move

AV Receiver

PV Recorder

Set Top Box

Custom

Move

INFO

Device Setting

INFO

Device Setting

INFO

Device Setting

POWER

CH CH

THUMB

STICK

POWER

CH CH

123

456

LAST CH

THUMB

STICK

SETUP

THUMB

STICK



TV/VCR

INFO



GUIDE

MORE..

THUMB

STICK

SELECT

MORE..

AV Receiver

PV Recorder

Set Top Box

Custom

Move

SEL

Select

POWER

CH CH

123

456

LAST CH



TV/VCR

INFO

GUIDE

THUMB

STICK

SELECT

ORIGINAL MENU

OF EQUIPMENT

Move

AV NET

Return



INFO

GUIDE

HITACHI AV NET WIZARD (Learning)

THUMB

STICK

Use this wizard to manually learn or modify your AV NET soft keys.

BACK Learn Modify

Move

SEL

Start Wizard

THUMB

STICK

SELECT

GUIDE

See Page 30

Move

AV NET

ORIGINAL GUIDE

OF EQUIPMENT

Return

DVD

VCR

Cable Box

Photo MC

Move

INFO

POWER MENU MORE..

Device Setting

Page 30

HOW TO USE THE REMOTE CONTROL TO

CONTROL YOUR TV

THE REMOTE CONTROL

AV NET LEARNING WIZARD

This function of the AV NET makes it more expandable because it allows the user to use equipment that is not supported by the pre-code library, listed on page 22. For example, after programming your equipment to the AV NETand the soft keys do not work, the user just has to follow the steps below. The AV NET Learning Wizard will transfer any remote button IR code of your equipment to the soft keys of your AV NET. If all remote button transfers are successful, the user can now control their equipment by using the TV remote control.

NOTE: It is very important to point the equipment’s remote control directly to the LEARNING AVNET sensor located on the TV

screen (see page 7) while trying to transfer the desired remote control button to the AV NET.

Learn

HITACHI AV NET WIZARD (Learning) Use this wizard to manually learn

or modify your AV NET soft keys.

BACK Learn Modify

HITACHI AV NET WIZARD (Learning) A device is stored in memory.

To learn a new device AV Net will replace the current device.

BACK Add New Device

Add New

Device

HITACHI AV NET WIZARD (Learning) Which device do you want to add?

(•) DVD2 ( ) VCR2 ( ) STB2 ( ) CBL2 ( ) PVR2

BACK NEXT

Select

Softkey

HITACHI AV NET WIZARD (Learning) Select the DVD2 softkey to learn?

TV Softkeys

BACK

POWER

SELECT EXIT

Yes

HITACHI AV NET WIZARD (Learning) Press and hold desired button to

transfer the command to AV NET.

Please wait while AV NET Learns the command...

HITACHI AV NET WIZARD (Learning)

Transfer was successfull Press OK to continue.

BACK OK

HITACHI AV NET WIZARD (Learning) Select another DVD2 softkey to learn?

TV Softkeys

Done Continue

POWER

SELECT EXIT

Done

HITACHI AV NET WIZARD (Learning) DVD2 (Custom)

Video Input No Connection Audio Input No Connection

Transmission Test POWER PLAY CH UP

BACK OK EXIT

HITACHI AV NET SETTING LIST

EXIT

SEL

Select

HITACHI AV NET WIZARD (Learning)

Transfer not completed! Try again?

NO YES

Yes

DVD2

Set Top Box

Cable Box

POWER

Move

INFO

Device Setting

Continue

Move

SEL

Start Wizard

Move

SEL

Initialize

Move

SEL

Move

SEL

Select

Next Step

Move

SEL

Select

Move

SEL

Select

Move

SEL

Select

Move

SEL

Select

THUMB

STICK

SELECT

THUMB

STICK

SELECT

THUMB

STICK

SELECT

THUMB

STICK

SELECT

THUMB

STICK

SELECT

THUMB STICK

SELECT

THUMB

STICK

SELECT

THUMB

STICK

SELECT

BACK

Highlight CUSTOM, and THUMBSTICK  to enter AV NET WIZARD. Select MODIFY to make changes on equipment already stored in the CUSTOM memory.

This page will not appear at initial set up.

Select the device (equipment) to be added for soft key learning.

Select soft key to be learned.

NOTE: To access the cursor function of a

specific equipment (Ex. DVD), select the “MENU” soft key on OSD, and press the MENU button of the Projection TV remote control. In order to use THUMBSTICK and EXIT button of the Projection TV remote control, “arrows, select, and EXIT” button must be learned. Then the menu of the programmed equipment can be controlled with the Projection TV remote control.

Page 31

HOW TO USE THE REMOTE CONTROL TO CONTROL YOUR TV

THE REMOTE CONTROL

 ASPECT button

Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal, the picture format ratio allows you to adjust the images through the following options. 4:3 Standard Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the

left and right of the image to preserve the original aspect ratio of the source. Note: Use this mode for only 15% of your total viewing time to prevent uneven aging of the phosphors. Phosphors in the lighted area of the picture will age more rapidly than the black areas.

4:3 Expanded use this aspect mode to display conventional (4:3) sources by expanding the outer edges of the image

to fill the 16:9 screen. The center of the image remains unaltered. 4:3 Zoom1/Zoom2 Use these aspect modes to zoom in on conventional (4:3) sources. 16:9 Standard Use this aspect mode to display 16:9 sources like HDTV and DVD’s preserving the original 16:9 aspect

ratio. 16:9 Zoom Use this aspect mode to zoom 16:9 images.

(1) NTSC/480i/480p Input

(2) 480i/480p INPUT

(3) 720p/1080i INPUT

4:3

INPUT

4:3 EXPANDED

4:3 ZOOM1

4:3 ZOOM2

16:9 STANDARD

4:3 STANDARD

INPUT

4:3 EXPANDED

4:3 ZOOM1

4:3 ZOOM2

16:9 STANDARD

4:3 STANDARD

INPUT

16:9

16:9 STANDARD 16:9 ZOOM

16:9 ZOOM

16:9

NOTE: The Aspect Style setting you

select for an ANT input will automatically be set for the other ANT inputs. However, all five video inputs have independent Aspect Style settings.

Page 32

HOW TO USE THE REMOTE TO

CONTROL YOUR TV

 VIRTUAL HD button

Press this button to toggle between 1080i and 540p. 540p and 1080i represent two ways to display the TV signal.

• Progressive: The “p” in 540p tells you that the display is showing you the picture in the progressiveformat. With the progressive format the complete picture is created by drawing lines across the screen from left to right which fill the screen from the top to the bottom. If you look very closely at the screen there will be a very small space between each line. The progressive format is good for displaying fast moving programs such as a sporting event.

• Interlaced: The “i” in 1080i tells you that the display is showing you the picture in the interlaced format. With the interlaced format the picture is created by drawing lines across the screen from left to right which fill the screen from top to bottom, and then returning to the top and drawing another set of lines in between the first set. The TV draws the lines so fast that our eyes can’t see them. If you look very closely at the screen you will notice a smoother image than with the progressive format. The interlaced format is good for displaying detailed images like feature films.

•You can compare the progressive and interlaced formats by toggling the “VIRTUAL HD” button on the remote control. Some people like the crisp picture from 540p and some people like the smooth and detailed 1080i. Hitachi offers you the choice.

 MENU button

The MENU button will start the On-Screen Display.

 EXIT button

When in MENU mode, this button will exit all On-Screen Displays.

 THUMB STICK/SELECT button

All the On-Screen Display features can be set or adjusted by using the THUMB STICK, except for numeric entries. The THUMB STICK will highlight functions or adjust and set different features. Press the THUMB STICK toward desired direction and press down to SELECT.

When no on-screen displays are on the TV screen, use THUMB STICK  or  to access the Favorite Channels feature. To add channels to Favorite Channels, use the number keys to enter the channel number. Use THUMB STICK  to highlight “Add”,

then press SELECT to store the channel to the Favorite Channel feature. To delete (Del) the channel from the Favorite Channel, use THUMB STICK  ,  to highlight the channel, then THUMB STICK 

to highlight Delete (Del) and press SELECT to delete. To view a Favorite Channel use THUMB STICK  ,  to highlight the channel and press SELECT to view.

Favorite Channels

Move

Ant A 8

A6 A3

- - - - -

THUMB

STICK

THUMB

STICK

Add

SEL

Select

Favorite Channels

Move

Ant A 8

A6 A3

- - - - -

Del

THUMB

STICK

SELECT

NOTE: The VIRTUAL HD button will not change the picture with a 1080i HDTV input. HDTV signals bypass the VIRTUAL HD

circuitry and are shown in their native 1080i format.

 VOLUME, MUTE button

Press the VOLUME up () or down () button until you obtain the desired sound level. To reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc., press the MUTE button. Press the

MUTE button again to turn the sound off completely (MUTE). To restore the sound, press the MUTE button one more time, or press the VOLUME Up () button.

Closed Captioning will display when MUTE/SOFT MUTE is on and Closed Caption is set to AUTO (see page 71).

Volume 8

Mute 8

Soft Mute 8

THE REMOTE CONTROL

MUTE

Page 33

HOW TO USE THE REMOTE TO CONTROL YOUR TV

LAST CHANNEL (LAST CH) button

Use this button to select between the last two channels viewed (Good for watching two sporting events, etc.).

PICTURE-IN-PICTURE buttons

See separate section on pages 34~36 for a description.

SURF button

Press the SURF button to automatically scan all active channel numbers (those set in memory) and display them as PIP subpictures. Press the SURF button a second time to remove the sub-pictures from the screen.

VID1 ~ VID5

When the remote control is in TV mode, press these buttons to directly select the video input sources between the five video inputs.

DAY/NIGHT button

Press this button to toggle between Day and Night picture mode settings. Select Day for day time viewing with more brightness and contrast to compete with room light. Select Night for night time viewing with less brightness and contrast for a more detailed picture (see page 47 for settings changes).

3:32 PM

Ant A 10

Stereo

3:32 PM

Ant A 39

Stereo

LAST CH

Ant A 28

TAKA

YPBPR:1

VID1

Stereo

ST/SA

Video:2

VID2

Video:4

VID4

Video:5

VID5

Video:3

VID3

VID 1 VID 2

VID 3

VID 4

VID 5

Ant

SURF

NOTES: 1. If no buttons are pressed when in SURF mode, auto-scanning will continuously scan channels in memory (see

page 55).

2. If a channel is changed during this SURF scanning, sub-pictures will be removed from the screen.

3. If MOVIE/TV RATINGS LOCK setting is ON, PIP SURF mode will be deactivated.

4. CLOSED CAPTION will not appear when PIP SURF mode is on.

5. The SURF button will only work in ANT A and ANT B.

6. While in SURF scanning mode, press SELECT on the remote control to stop on a chosen channel. Press SELECT again to resume SURF scanning.

THE REMOTE CONTROL

SURF

Page 34

3434

PICTURE-IN-PICTURE (PIP)

Use above connection to view VCR program as a sub-picture while viewing another program as main picture (ANT A, ANT B, V:1, V:2, V:3, or V:5). You may also view the VCR program as a main picture while viewing another program as a sub-picture (ANT A, V:1, V:2, V:3, or V:5).

 PIP button

Press the PIP button and a sub-picture will appear in one of the three different modes (POP, PIP and SPLIT), depending on the last selection of the PIP mode. To change the PIP mode, use the PIP MODE button to cycle through the three different modes.

POP MODE PICTURE-IN-PICTURE

Press the PIP button and a sub-picture appears in one of the three different modes (POP, PIP and SPLIT), depending on the last selection of the PIP mode. Press the PIP button again to remove the sub-picture from the screen. Use the SWAP button to select between main and sub-picture tuning control (indicated by green highlighted channel display.) Press the VID1, VID2, VID3, VID4 or VID5 button when sub-picture channel tuning is being controlled, to change between VIDEO: 1, VIDEO: 2, VIDEO: 3, VIDEO:4, VIDEO:5 and ANT:A sources, (ANT B source cannot be viewed as a sub-picture.)

PIP MODE PICTURE-IN-PICTURE

This feature is only available with a 1080i input signal (Component and DVI-HDTV).

NOTES: 1. In POP mode, thumb stick CURSOR  ,  will move the sub-picture up/down.

2. Only sound from the main picture can be heard.

Your HITACHI Projection TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. The Dual Tuner can operate with only one input (ANTAonly) or two inputs (ANTA and ANT B).

ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture. To select between main picture and PIP sub-picture tuning, press the SWAP button on the remote. The green highlighted channel display will move with every press of the SWAP button. When the top channel display is highlighted, channel tuning is for the main picture. When the lower channel display is highlighted, channel tuning is for the PIP sub-picture.

The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing other programs from the ANTAsource or any of the video inputs.

,







EXIT

CHVOL

MUTE

PIP SURF

SWAP

FREEZE

PIP MODE

PIP ACCESS

DAY/NIGHT

REC

SELECT

LAST CH

VID 2

VID 3

VID 4

VID 5

DVI-HDTV

CENTER

DVI-HDTV DVI-HDTV

CENTER

ANT A

TO CONVERTER

ANT B

(MONO)/L

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

VIDEO

INPUT 1

INPUT 2

INPUT 3

MONITOR

OUT

ANT A

TO CONVERTER

ANT B

(MONO)/L

IR BLASTER

AUDIO TO HI-FI

S-VIDEO

Y/VIDEO

(MONO)/L

(MONO)/L VIDEO

LVIDEO

INPUT 1

INPUT 2

INPUT 3

INPUT 4

MONITOR

OUT

OUTPUT

Audio Video

VCR

IR BLASTER

AUDIO TO HI-FI

AUDIO

OUTPUT

Audio Video

VCR

(MONO)/L VIDEO

INPUT 4

(MONO)/L VIDEO

THE REMOTE CONTROL

Models: 57T500

65T500

Models: 57X500

65X500

Main Picture

Sub Picture

PIP

PIP MODE

Page 35

PICTURE-IN-PICTURE (PIP)

SPLIT MODE PICTURE-IN-PICTURE

Split Mode PIP displays the main picture and sub-picture evenly on the screen.

 SWAP button (with PIP ON)

Press this button to toggle between the Main and Sub picture which is highlighted with a green border around the picture. Picture sound and channel can be controlled when it is highlighted.

NOTE: The SWAP button will only operate in POP/PIP/SPLIT PIP mode.

Main Picture

Sub Picture

 PIP MODE button

To change between the available PIP modes (moving picture - SPLIT, POP or PIP; freeze picture - SPLIT, STROBE, MAIN and SUB) press the PIP MODE button when PIP is ON. Each press of this button will change PIP to a different mode. Pressing this button two times will cycle through both PIP modes.

a) Moving Picture

THE REMOTE CONTROL

b) Freeze Picture

NOTE: PIP modes will depend on the type of signal format

received.

NOTE: Freeze modes will depend on the type of signal for-

mat received.

SWAP

SPLIT

PIP MODE

PICTURE-IN-PICTURE (PIP) MODES

POP PIP SPLIT NTSC (ANT A/B) 480i 480p 720p 1080i

YES x YES YES x YES

xxYES x xYES x YES YES

Freeze

PIP MODE

Freeze

PIP MODE

Freeze

Freeze Freeze Freeze

FREEZE MODES

POP PIP SPLIT STROBE NTSC (ANT A/B) 480i 480p 720p 1080i

YES x YES YES

xxYES X x xYES X x YES YES X

Page 36

PICTURE-IN-PICTURE (PIP)

 FREEZE button (With PIP ON)

If you wish to freeze the sub-picture, press the FREEZE button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the FREEZE button again.

 FREEZE button (with PIP OFF)

Press the FREEZE button to freeze the picture, depending on the PIP mode selected (POP Main Freeze, POP Sub Freeze, SPLIT or STROBE). To change FREEZE modes, use the PIP MODE button to cycle through the four different modes.

POP MAIN FREEZE (with PIP OFF)

PIP FREEZE should be in POP Main mode. Press the FREEZE button to freeze one frame of the picture you are currently viewing and the frozen frame will show in the Main Picture. Press this button again or PIP to return to normal viewing. This feature is useful for freezing a picture frame with addresses.

POP SUB FREEZE (with PIP OFF)

PIP FREEZE should be in POP Sub mode. Press the FREEZE button to freeze the sub-picture. Press the FREEZE button again or the PIP button to return to normal viewing.

NOTES: Each freeze frame is delayed about 0.1 (1/10) second.

NOTE: When PIP is on, the FREEZE function will only operate when POP/PIP/SPLIT mode is chosen.

STROBE FREEZE(with PIP OFF)

PIP FREEZE should be in STROBE mode. Press the FREEZE button to freeze three frames of the picture you are currently viewing. Press this button again or PIP to return to normal viewing. This feature is useful for viewing a moving picture that has many details, for example, a close play in a sporting event or a golf swing.

FREEZE

SPLIT FREEZE(with PIP OFF)

PIP FREEZE should be in SPLIT mode. Press the FREEZE button to freeze the picture you are currently viewing (only the right sub-picture will freeze). Press the FREEZE button again or the PIP button to return to normal viewing.

Main Picture

Sub Picture

FREEZE

THE REMOTE CONTROL

Hot Springs Clay Mask

C/O John Doe

Run-Spa Retreat

P.O. Box 55512

Any Town, USA98765

Check or

Money Order Only

1-800-555-1212

FREEZE

Hot Springs Clay Mask

C/O John Doe

Run-Spa Retreat

P.O. Box 55512

Any Town, USA 98765

Check or

Money Order Only

1-800-555-1212

Hot Springs Clay Mask

C/O John Doe

Run-Spa Retreat

P.O. Box 55512

Any Town, USA98765

Check or

Money Order Only

1-800-555-1212

FREEZE

Hot Springs Clay Mask

C/O John Doe

Run-Spa Retreat

P.O. Box 55512

Any Town, USA98765

Check or

Money Order Only

1-800-555-1212

FREEZ

Page 37

USING THE REMOTE TO CONTROL VCR FUNCTIONS

Operating the precoded function for your VCR.

This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR (refer to page 44 for pre-codes).

1. Turn ON your VCR.

2. Aim the remote control at the front of your VCR.

3. Press and release the VCR button to switch to VCR pre-coded mode.

4. Hold down the VCR button on the remote and enter the two digit preset code that matches your VCR, as shown on page 44. The indicator light will flash 3 times if the code was accepted.

5. Aim the remote at the VCR and press the POWER button. The remote will turn off your VCR when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your VCR. If the VCR does not turn off, try a different two digit preset code.

6. The remote will now control your VCR.

NOTES:

1. If your VCR cannot be operated after performing the above procedures, your VCR’s code has not been precoded into the remote.

2. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide.

3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

4. The MENU button will act as the VCR MENU button for HITACHI VCRs.

5. The LAST CH button will act as your VCR ENTER button if required.

6. The SLEEP button will act as your VCR ‘100’ button if required.

 VCR Button

This button allows the remote to control your VCR by setting it to VCR mode.

 PRECODED VCR Buttons

These buttons transmit the chosen precoded VCR codes. For some VCRs, you must press the RECORD button twice to record a program.

 EXCLUSIVE TV Buttons

These buttons are for operating the TV.



















POWER

VCR

CBL

DVD

INFOSLEEP

A/V NET

EXIT

CHVOL

MUTE

PIP SURF

SWAP

FREEZE

PIP MODE

PIP ACCESS

DAY/NIGHT

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

LAST CH

VID 1

VID 2

VID 3

VID 4

VID 5

PVR

AMP

VIRTUAL HD

MY VCR CODE IS:

NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR.

THE REMOTE CONTROL

Page 38

USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS

Operating the precoded function for your cable box.

This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of your cable box (refer to page 44).

1. Turn ON your cable box.

2. Aim the remote control at the front of your cable box.

3. Press and release the Cable (CBL) button to switch to Cable pre-coded mode.

4. Hold down the CBL button on the remote and enter the two digit preset code that matches your cable box as shown on page 44. The indicator light will flash 3 times if the code was accepted.

5. Aim the remote at the cable box and press the POWER button. The remote will turn off your cable box when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different two digit preset code.

6. The remote will now control your Cable box.

NOTES:

1. If your cable box cannot be operated after performing the above procedures, your cable box code has not been precoded into the remote.

2. In the unlikely event that your cable box cannot be operated after performing the above procedures, please consult your cable box operating guide.

4. The LAST CH button will act as the cable box ENTER button if required.

5. The SLEEP button will act as your cable box ‘100’ button if required.

6. The ANT button will act as the TV/STB button when in STB mode.

 CABLE (CBL) button

This button allows the remote to control your cable box by setting it to CABLE mode.

 PRECODED CABLE BOX buttons

These buttons transmit the chosen precoded cable codes.

 EXCLUSIVE TV buttons

These buttons are for operating the TV.











POWER

VCR

CBL

DVD

INFOSLEEP

A/V NET

EXIT

CHVOL

MUTE

PIP SURF

SWAP

FREEZE

PIP MODE

PIP ACCESS

DAY/NIGHT

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

LAST CH

VID 1

VID 2

VID 3

VID 4

VID

PVR

AMP

VIRTUAL HD

MY CABLE BOX CODE IS:

NOTE: Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box.

THE REMOTE CONTROL

Page 39

USING THE REMOTE TO CONTROL SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS

Operating the precoded function for your set-top-box/satellite receiver.

This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set-top-box/satellite systems (refer to page 44).

1. Turn ON your set-top-box/satellite systems.

2. Aim the remote control at the front of your set-top-box/satellite systems.

3. Press and release the SET-TOP-BOX (STB) button to switch to set-top-box/satellite pre-coded mode.

4. Hold down the STB button on the remote and enter the two digit preset code that matches your set-top-box/satellite receiver as shown on page 44. The indicator light will flash 3 times if the code was accepted.

5. Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satellite receiver when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your settop-box/satellite receiver. If the set-top-box/satellite receiver does not turn off, try a different two digit preset code.

6. The remote will now control your set-top-box/satellite receiver.

NOTES:

1. If your set-top-box/satellite receiver cannot be operated after performing the above procedures, your set-topbox/satellite receiver code has not been precoded into the remote.

2. In the unlikely event that your set-top-box/satellite receiver cannot be operated after performing the above procedures, please consult your set-top-box/satellite receiver operating guide.

4. The ANT button will act as the TV/STB button when in STB mode.

 SET-TOP-BOX (STB) button

This button allows the remote to control your satellite receiver by setting it to SET-TOP-BOX/SATELLITE mode.

 PRECODED SET-TOP-BOX/SATELLITE RECEIVER but-

tons

These buttons transmit the chosen precoded set-topbox/satellite codes.

 EXCLUSIVE TV buttons

These buttons are for operating the TV.



















POWER

VCR

CBL

DVD

INFOSLEEP

A/V NET

EXIT

CHVOL

MUTE

PIP SURF

SWAP

FREEZE

PIP MODE

PIP ACCESS

DAY/NIGHT

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

LAST CH

VID 1

VID 2

VID 3

VID 4

VID 5

PVR

AMP

VIRTUAL HD

MY SATELLITE RECEIVER/STB CODE IS:

NOTE: Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-top-

box/satellite receiver.

THE REMOTE CONTROL

Page 40

USING THE REMOTE TO CONTROL DVD FUNCTIONS

Operating the precoded function for your DVD player.

This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player (refer to page 44 for pre-codes).

1. Turn ON your DVD player.

2. Aim the remote control at the front of your DVD player.

3. Press and release the DVD button to switch to DVD pre-coded mode.

4. Hold down the DVD button on the remote and enter the two digit preset code that matches your DVD player, as shown on page 44. The indicator light will flash 3 times if the code was accepted.

5. Aim the remote at the DVD player and press the POWER button. The remote will turn off your DVD player when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not turn off, try a different two digit preset code.

6. The remote will now control your DVD player.

7. You will need to set the display type of your DVD player to 16:9 widescreen.

NOTES:

1. If your DVD player cannot be operated after performing the above procedures, your DVD player’s code has not been precoded into the remote.

2. In the unlikely event that your DVD player cannot be operated after performing the above procedures, please consult your DVD player operating guide.

 DVD Button

This button allows the remote to control your DVD player by setting it to DVD mode.

 PRECODED DVD Buttons

These buttons transmit the chosen precoded DVD codes.

 EXCLUSIVE TV Buttons except number buttons

These buttons are for operating the TV. The number buttons can also be used for operating your DVD.











POWER

VCR

CBL

DVD

INFOSLEEP

A/V NET

EXIT

CHVOL

MUTE

PIP SURF

SWAP

FREEZE

PIP MODE

PIP ACCESS

DAY/NIGHT

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

LAST CH

VID 1

VID 2

VID 3

VID 4

VID 5

PVR

AMP

VIRTUAL HD

MY DVD PLAYER CODE IS:

NOTE: Refer to instruction manual of the DVD player for operation of the buttons exclusively for the DVD player.

THE REMOTE CONTROL

Page 41

USING THE REMOTE TO CONTROL PVR FUNCTIONS

THE REMOTE CONTROL

Operating the precoded function for your PVR (Personal Video Recorder).

This remote is designed to operate different types of PVRs. You must first program the remote to match the remote system of your PVR (refer to page 44 for pre-codes).

1. Turn ON your PVR.

2. Aim the remote control at the front of your PVR.

3. Press and release the PVR button to switch to PVR pre-coded mode.

4. Hold down the PVR button on the remote and enter the two digit preset code that matches your PVR, as shown on page 44. The indicator light will flash 3 times if the code was accepted.

5. Aim the remote at the PVR and press the POWER button. The remote will turn off your PVR when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your PVR. If the PVR does not turn off, try a different two digit preset code.

6. The remote will now control your PVR.

NOTES:

1. If your PVR cannot be operated after performing the above procedures, your PVR’s code has not been precoded into the remote.

2. In the unlikely event that your PVR cannot be operated after performing the above procedures, please consult your PVR operating guide.

 PVR Button

This button allows the remote to control your PVR by setting it to PVR mode.

 PRECODED PVR Buttons

These buttons transmit the chosen precoded PVR codes.

 EXCLUSIVE TV Buttons

These buttons are for operating the TV.









POWER

VCR

CBL

DVD

INFOSLEEP

PHOTO

EXIT

CHVOL

MUTE

PIP SURF

SWAP

FREEZE

PIP MODE

PIP ACCESS

DAY/NIGHT

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

LAST CH

VID 1

VID 2

VID 3

VID 4

VID 5

PVR

AMP

VIRTUAL HD

MY PVR CODE IS:

NOTE: Refer to instruction manual of the PVR for operation of the buttons exclusively for the PVR.

NOTE: The C.C. button functions as “replay”.

Page 42

THE REMOTE CONTROL

USING YOUR REMOTE

TO CONTROL ADDITIONAL AUDIO EQUIPMENT

Operating the precoded function for your Audio component.

This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component (refer to page 44 for pre-codes).

1. Turn ON your Audio component you wish to control with the Remote.

2. Aim the remote control at the front of your Audio component.

3. Press and release the CD or AMP button (Audio buttons) to switch to Audio component pre-coded mode.

4. Hold down the CD or AMPbutton on the remote and enter the two digit preset code that matches your Audio component, as shown on page 44. The indicator light will flash 3 times if the code was accepted.

5. Aim the remote at the Audio component and press the POWER button. The remote will turn off your Audio component when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio component does not turn off, try a different two digit preset code.

6. The remote will now control your Audio component.

7. Repeat steps 1 - 6 if you wish to program the remote to control another Audio component. Be sure to use a different Audio button on the remote, since only one component can be programmed per button.

NOTES:

1. If your Audio component cannot be operated after performing the above procedures, your Audio component’s code has not been precoded into the remote.

2. In the unlikely event that your Audio componentcannot be operated after performing the above procedures, please consult your Audio equipment operating guide.

 CD and AMP Buttons

These buttons allow the remote to control your Audio equipment by setting it to Audio mode.

 PRECODED AUDIO Buttons

These buttons transmit the chosen precoded Audio component codes.

 EXCLUSIVE TV Buttons

These buttons are for operating the TV.











POWER

VCR

CBL

DVD

INFOSLEEP

A/V NET

EXIT

CHVOL

MUTE

PIP SURF

SWAP

FREEZE

PIP MODE

PIP ACCESS

DAY/NIGHT

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

LAST CH

VID 2

VID 3

VID

PVR

AMP

VIRTUAL HD

MY AUDIO EQUIPMENT CODE IS:

NOTE: Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment.

AMP/RCVR

Page 43

THE SIMPLE REMOTE CONTROL



 POWER button

Press Power button to turn the Projection TV ON or OFF.

 CH+ (), CH- ()

Press the CH+ () up or CH- ()down buttons to select desired channel or to navigate the on screen display features when in AV NET mode.

 VOL- (), VOL+ ()

Press the VOL- () down or VOL+ ()up buttons to select desired sound level or to navigate the on screen display features when in AV NET mode.

 SELECT button

Press SELECT button to Select when in MENU and AV NET mode.

 MUTE button

To reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc., press the MUTE button. Press the MUTE button again to turn the sound off completely (MUTE). To restore the sound, press the MUTE button one more time, or press the VOLUME Up () button. (See complete explanation and example on page 32, Item .)

 FAV CH button

Press FAV CH button to access your favorite channels.

 ANT button

The ANT button will select between Antenna A and Antenna B each time the button is pressed. (See example on page 25, item

.)

 EXIT button

When in MENU mode, this button will exit all On-Screen Displays.

 MENU button

Press the MENU button to start the On-Screen Display.

 AV NET

Press this button to access the Audio/Video network (AV Net) menu. The AV Net allows the user to control external components with the TV’s remote control. (See complete explanation and example on page 26, item .)

HITACHI has provided a second remote control for your convenience. The Simple Remote Control has the basic features that are most often used.

NOTE: The Simple Remote cannot be programmed to control external components.

(Patent Pending)

THE REMOTE CONTROL

CH +

A/V NET











VOL -

MUTE

SELECT

CH -

EXIT

VOL +



FAV CH

ANT







POWER

Page 44

VCR, CABLE, SATELLITE, DVD and

AUDIO/VIDEO CODES FOR REMOTE CONTROL

VCR BRAND. . . . . . . . . . . . . . . . . CODE

Adventura . . . . . . . . . . . . . . . . . . . . . . 01

Aiko. . . . . . . . . . . . . . . . . . . . . . . . . . . 09

Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . 01

Akai. . . . . . . . . . . . . . . . . . . . . 02, 47, 48

American High. . . . . . . . . . . . . . . . . . . 23

Asha . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Audiovox. . . . . . . . . . . . . . . . . . . . . . . 24

Beaumark . . . . . . . . . . . . . . . . . . . . . . 44

Bell & Howell . . . . . . . . . . . . . . . . . . . . 32

Broksonic. . . . . . . . . . . . . . . . . 33, 34, 41

Calix . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Canon. . . . . . . . . . . . . . . . . . . . . . . . . 23

Carver. . . . . . . . . . . . . . . . . . . . . . . . . 31

CCE . . . . . . . . . . . . . . . . . . . . . . . . . . 09

Citizen. . . . . . . . . . . . . . . . . . . . . . 09, 24

Craig . . . . . . . . . . . . . . . . . . . . 19, 24, 44

Curtis Mathes . . . . . . . . . . . . . 02, 23, 46

Cybernex. . . . . . . . . . . . . . . . . . . . . . . 44

Daewoo . . . . . . . . . . . . . . . . . . . . . 09, 17

Dynatech. . . . . . . . . . . . . . . . . . . . . . . 01

Electrohome . . . . . . . . . . . . . . . . . . . . 24

Electrophonic. . . . . . . . . . . . . . . . . . . . 24

Emerex . . . . . . . . . . . . . . . . . . . . . . . . 08

Emerson . . . . . . . . 01, 09, 13, 16, 24, 27,

. . . . . . . . . . . . . . . 28, 33, 34, 36, 41, 47

Fisher . . . . . . . . . . . . . . . . . . . 19, 21, 32

Fuji . . . . . . . . . . . . . . . . . . . . . . . . 10, 23

Funai. . . . . . . . . . . . . . . . . . . . . . . . . . 01

Garrard . . . . . . . . . . . . . . . . . . . . . . . . 01

GE . . . . . . . . . . . . . . . . . . . 04, 23, 40, 46

Goldstar. . . . . . . . . . . . . . . . . . 24, 25, 43

Gradiente . . . . . . . . . . . . . . . . . . . . . . 01

Harley Davidson . . . . . . . . . . . . . . . . . 01

Harmon/Kardon. . . . . . . . . . . . . . . . . . 25

Headquarter . . . . . . . . . . . . . . . . . . . . 18

Hi-Q . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Hitachi . . . . . . . . . . . . . 01, 02, 03, 04, 05

Jensen . . . . . . . . . . . . . . . . . . . . . . . . 02

JVC. . . . . . . . . . . . . . . . . . . . . 02, 14, 26

KEC . . . . . . . . . . . . . . . . . . . . . . . 09, 24

Kenwood . . . . . . . . . . . . . . . . . 02, 25, 26

KLH. . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Kodak . . . . . . . . . . . . . . . . . . . . . . 23, 24

Lloyd. . . . . . . . . . . . . . . . . . . . . . . . . . 01

Lloyd’s. . . . . . . . . . . . . . . . . . . . . . . . . 27

LXI . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Magnavox . . . . . . . . . . . . . 15, 23, 31, 35

Magnin . . . . . . . . . . . . . . . . . . . . . . . . 44

Marantz. . . . . . . . . . . . . . . . . . . . . 23, 31

Marta. . . . . . . . . . . . . . . . . . . . . . . . . . 24

Matsushita. . . . . . . . . . . . . . . . . . . . . . 23

MEI. . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Memorex. . . . . . . . . . . . . . 01, 15, 18, 19,

. . . . . . . . . . . . . . . . . . 20, 23, 24, 32, 44

MGA . . . . . . . . . . . . . . . . . . . . . . . 16, 47

MGN Technology. . . . . . . . . . . . . . . . . 44

Minolta . . . . . . . . . . . . . . . . . . . . . 03, 05

Mitsubishi. . . . . . . . . . . 16, 26, 39, 47, 48

Motorola . . . . . . . . . . . . . . . . . . . . 20, 23

MTC . . . . . . . . . . . . . . . . . . . . . . . 01, 44

Multitech . . . . . . . . . . . . . . . . . . . . . . . 01

NEC. . . . . . . . . . . . . . . . . . 02, 25, 26, 32

Nikko. . . . . . . . . . . . . . . . . . . . . . . . . . 24

Noblex. . . . . . . . . . . . . . . . . . . . . . . . . 44

Olympus . . . . . . . . . . . . . . . . . . . . 12, 23

Optimus . . . . . . . . . . . . . . . . . 20, 24, 32

Panasonic . . . . . . . . . . . . . 11, 12, 23, 38

Penney . . . . . . . . . . . . 03, 23, 24, 25, 44

Pentax. . . . . . . . . . . . . . . . . . . 03, 04, 05

Philco . . . . . . . . . . . . . . . . . . . . . . . . . 23

Phillips. . . . . . . . . . . . . . . . . . . . . . 23, 31

Pilot. . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Pioneer . . . . . . . . . . . . . . . . . . . . . . . . 26

Pulsar . . . . . . . . . . . . . . . . . . . . . . . . . 15

Quarter . . . . . . . . . . . . . . . . . . . . . . . . 18

Quartz. . . . . . . . . . . . . . . . . . . . . . . . . 18

Quasar . . . . . . . . . . . . . . . . . . . . . . . . 23

Radio Shack . . . . . . . . . . . . . . . . . 01, 24

Radix. . . . . . . . . . . . . . . . . . . . . . . . . . 24

Randex . . . . . . . . . . . . . . . . . . . . . . . . 24

RCA. . . . . . . . . . . . 03, 04, 05, 35, 40, 46

Realistic . . . . . . . . . . . . . . 01, 18, 19, 20,

. . . . . . . . . . . . . . . . . . 21, 23, 24, 32, 44

Ricoh. . . . . . . . . . . . . . . . . . . . . . . . . . 22

Runco . . . . . . . . . . . . . . . . . . . . . . . . . 15

Samsung. . . . . . . . . . . . . . . . . . . . 17, 44

Sanky . . . . . . . . . . . . . . . . . . . . . . 15, 20

Sansui. . . . . . . . . . . . . . . . . . . . . . 02, 26

Sanyo . . . . . . . . . . . . . . . . 18, 19, 32, 44

Scott . . . . . . . . . . . 16, 17, 33, 34, 36, 41

Sears . . . . . . . . . . . . . . . . 03, 05, 18, 19,

. . . . . . . . . . . . . . . . . . . . . 21, 23, 24, 32

Sharp . . . . . . . . . . . . . . . . . . . . . . . . . 20

Shintom. . . . . . . . . . . . . . . . . . . . . . . . 30

Shogun . . . . . . . . . . . . . . . . . . . . . . . . 44

Sony . . . . . . . . . . . . . . . . . 08, 10, 22, 23

STS. . . . . . . . . . . . . . . . . . . . . . . . . . . 03

Sylvania . . . . . . . . . . . . . . . 01, 16, 23, 31

Symphonic . . . . . . . . . . . . . . . . . . . . . 01

Tatung . . . . . . . . . . . . . . . . . . . . . . . . . 02

Teac . . . . . . . . . . . . . . . . . . . . . . . 01, 02

Technics . . . . . . . . . . . . . . . . . . . . 23, 38

Teknika . . . . . . . . . . . . . . . . . . 01, 23, 24

TMK . . . . . . . . . . . . . . . . . . . . . . . . 27,44

Toshiba . . . . . . . . . . . . . . . 16, 17, 21, 36

Totvision . . . . . . . . . . . . . . . . . . . . 24, 44

Unitech . . . . . . . . . . . . . . . . . . . . . . . . 44

Vector . . . . . . . . . . . . . . . . . . . . . . . . . 17

Vector Research . . . . . . . . . . . . . . . . . 25

Video Concepts. . . . . . . . . . . . . . . 17, 47

Videosonic. . . . . . . . . . . . . . . . . . . . . . 44

Wards. . . . . . . . . . . . . 01, 03, 19, 20, 23,

. . . . . . . . . . . . . . . . . . . . . 35, 36, 44, 46

XR-1000 . . . . . . . . . . . . . . . . . . . . 01, 23

Yamaha. . . . . . . . . . . . . . . . . . . . . . . . 25

Zenith . . . . . . . . . . . . . . . . . . . 10, 15, 22

DVD BRAND. . . . . . . . . . . . . . . . . CODE

APEX . . . . . . . . . . . . . . . . . . . . . . . . . 15

Denon. . . . . . . . . . . . . . . . . . . . . . . . . 04

Go Video . . . . . . . . . . . . . . . . . . . . . . . 14

Hitachi. . . . . . . . . . . . . . . . . . . 07, 12, 13

JVC. . . . . . . . . . . . . . . . . . . . . . . . . . . 01

Kenwood. . . . . . . . . . . . . . . . . . . . 04, 16

Magnavox . . . . . . . . . . . . . . . . . . . . . . 05

Mitsubishi . . . . . . . . . . . . . . . . . . . . . . 10

Panasonic . . . . . . . . . . . . . . . . . . . . . . 04

Phillips . . . . . . . . . . . . . . . . . . . . . . . . 06

Pioneer . . . . . . . . . . . . . . . . . . . . . . . . 03

RCA (Proscan). . . . . . . . . . . . . . . . 09, 17

Samsung. . . . . . . . . . . . . . . . . . . . . . . 12

Sanyo . . . . . . . . . . . . . . . . . . . . . . . . . 13

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Toshiba . . . . . . . . . . . . . . . . . . . . . . . . 05

Yamaha. . . . . . . . . . . . . . . . . . . . . . . . 08

Zenith . . . . . . . . . . . . . . . . . . . . . . 05, 11

CABLE BRAND . . . . . . . . . . . . . . CODE

ABC . . . . . . . . . . . . . . . . . 01, 07, 08, 17,

. . . . . . . . . . . . . . . . . . 18, 20, 36, 37, 49

Antronix. . . . . . . . . . . . . . . . . . . . . . . . 39

Archer . . . . . . . . . . . . . . . . . . . 11, 24, 39

Belcor . . . . . . . . . . . . . . . . . . . . . . . . . 32

Cable Star. . . . . . . . . . . . . . . . . . . . . . 32

Century . . . . . . . . . . . . . . . . . . . . . . . . 11

Citizen. . . . . . . . . . . . . . . . . . . . . . . . . 11

Colour Voice . . . . . . . . . . . . . . . . . 30, 42

Comtronics . . . . . . . . . . . . . . . . . . 25, 28

Contec . . . . . . . . . . . . . . . . . . . . . . . . 21

Dae Ryung . . . . . . . . . . . . . . . . . . . . . 20

Eastern . . . . . . . . . . . . . . . . . . . . . . . . 14

Electricord. . . . . . . . . . . . . . . . . . . . . . 31

Everquest . . . . . . . . . . . . . . . . . . . . . . 51

Focus . . . . . . . . . . . . . . . . . . . . . . . . . 52

Garrard . . . . . . . . . . . . . . . . . . . . . . . . 11

GC Electronics. . . . . . . . . . . . . . . . 32, 39

Gemini. . . . . . . . . . . . . . . . 05, 38, 43, 51

General Instrument . . . . . . . . . . . . 01, 12

Goldstar. . . . . . . . . . . . . . . . . . . . . 10, 25

Hamlin. . . . . . . . . . . . . . . . 04, 13, 22, 23

Hitachi. . . . . . . . . . . . . . . . . . . . . . . . . 01

Hytex. . . . . . . . . . . . . . . . . . . . . . . . . . 36

Jasco. . . . . . . . . . . . . . . . . . . . . . . . . . 11

Jerrold . . . . . . . 01, 08, 12, 37, 49, 50, 51

Macom . . . . . . . . . . . . . . . . . . . . . . . . 35

Magnavox . . . . . . . . . . . . . . . . . . . . . . 15

Memorex. . . . . . . . . . . . . . . . . . . . . . . 03

Movie Time . . . . . . . . . . . . . . . 29, 31, 33

NSC . . . . . . . . . . . . . . . . . . . . 29, 33, 38

Oak . . . . . . . . . . . . . . . . . . . . . 21, 36, 46

Panasonic . . . . . . . . . . . . . . . . 02, 03, 09

Paragon . . . . . . . . . . . . . . . . . . . . . . . 03

Phillips . . . . . . . . . . . . . . . 11, 15, 16, 26,

. . . . . . . . . . . . . . . . . . . . . 30, 42, 43, 44

Pioneer . . . . . . . . . . . . . . . 06, 10, 19, 55

Popular Mechanics . . . . . . . . . . . . . . . 52

Pulsar . . . . . . . . . . . . . . . . . . . . . . . . . 03

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Realistic . . . . . . . . . . . . . . . . . . . . . . . 39

Recoton. . . . . . . . . . . . . . . . . . . . . . . . 52

Regal. . . . . . . . . . . . . . . . . . . . 04, 22, 34

Regency . . . . . . . . . . . . . . . . . . . . . . . 14

Rembrandt. . . . . . . . . . . . . . . . . . . 01, 38

Runco . . . . . . . . . . . . . . . . . . . . . . . . . 03

Samsung. . . . . . . . . . . . . . . . . . . . 10, 25

Scientific Atlanta. . . . . . 17, 20, 41, 45, 55

Signal . . . . . . . . . . . . . . . . . . . . . . 25, 51

Signature. . . . . . . . . . . . . . . . . . . . . . . 01

SL Marx. . . . . . . . . . . . . . . . . . . . . . . . 25

Sprucer . . . . . . . . . . . . . . . . . . . . . . . . 02

Starcom . . . . . . . . . . . . . . . . . . 37, 49, 51

Stargate. . . . . . . . . . . . . . . . . . . . . 25, 51

Starquest. . . . . . . . . . . . . . . . . . . . . . . 51

Starsight . . . . . . . . . . . . . . . . . . . . 53, 54

Sylvania . . . . . . . . . . . . . . . . . . . . . . . 18

Teleview . . . . . . . . . . . . . . . . . . . . . . . 25

Texscan. . . . . . . . . . . . . . . . . . . . . . . . 18

Tocom . . . . . . . . . . . . . . . . . . . 07, 27, 50

Toshiba . . . . . . . . . . . . . . . . . . . . . . . . 03

Tusa . . . . . . . . . . . . . . . . . . . . . . . . . . 51

TV 86 . . . . . . . . . . . . . . . . . . . . . . . . . 29

Unika. . . . . . . . . . . . . . . . . . . . . . . 11, 39

United Artists. . . . . . . . . . . . . . . . . . . . 36

United Cable . . . . . . . . . . . . . . . . . . . . 49

Universal . . . . . . . . 11, 24, 31, 32, 34, 39

Videoway . . . . . . . . . . . . . . . . . . . . . . 47

Viewstar. . . . . . . . . . . . . . . 15, 28, 29, 40

Zenith . . . . . . . . . . . . . . . . . . . . . . 03, 48

Zentek. . . . . . . . . . . . . . . . . . . . . . . . . 52

SATELLITE BRAND. . . . . . . . . . . CODE

Echostar . . . . . . . . . . . . . . . . . . . . . . . 04

Hitachi. . . . . . . . . . . . . . . . . . . . . . . . . 01

Hughes . . . . . . . . . . . . . . . . . . . . . . . . 05

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . 03

SET-TOP-BOX . . . . . . . . . . . . . . . CODE

Panasonic . . . . . . . . . . . . . . . . . . . . . . 06

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . 07

Samsung. . . . . . . . . . . . . . . . . . . . . . . 08

Zenith . . . . . . . . . . . . . . . . . . . . . . . . . 09

AMPLIFIER BRAND . . . . . . . . . . . CODE

Aiwa . . . . . . . . . . . . . . . . . . . . . . . 05, 06

Carver . . . . . . . . . . . . . . . . . . . 01, 06, 08

Denon. . . . . . . . . . . . . . . . . . . . . . . . . 10

Fisher . . . . . . . . . . . . . . . . . . . . . . 08, 11

Hitachi. . . . . . . . . . . . . . . . . . . . . . . . . 12

JVC. . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Kenwood . . . . . . . . . . . . . . 14, 15, 17, 18

Magnavox . . . . . . . . . . . . . . . . . . . 01, 06

Marantz . . . . . . . . . . . . . . . . . . 01, 06, 16

MCS . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Optimus . . . . . . . . . . . . 03, 04, 11, 15, 20

Panasonic . . . . . . . . . . . . . . . . . . . . . . 16

Philips . . . . . . . . . . . . . . . . . . . . . . 01, 06

Pioneer . . . . . . . . . . . . 03, 04, 20, 21, 22

Quasar . . . . . . . . . . . . . . . . . . . . . . . . 16

Sansui. . . . . . . . . . . . . . . . . . . . . . . . . 06

Sanyo . . . . . . . . . . . . . . . . . . . . . . . . . 11

Sharp . . . . . . . . . . . . . . . . . . . . . . . . . 15

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . 05

Technics. . . . . . . . . . . . 02, 16, 23, 24, 25

Victor. . . . . . . . . . . . . . . . . . . . . . . . . . 13

Wards . . . . . . . . . . 03, 05, 06, 08, 20, 21

Yamaha. . . . . . . . . . . . . . . . . . . . . 15, 26

CD BRAND. . . . . . . . . . . . . . . . . . CODE

Adcom. . . . . . . . . . . . . . . . . . . . . . . . . 01

Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . 02

California Audio Lab . . . . . . . . . . . . . . 03

Carver. . . . . . . . . . . . . . . . . . . . . . . . . 02

Denon. . . . . . . . . . . . . . . . . . . . . . . . . 04

DKK . . . . . . . . . . . . . . . . . . . . . . . . . . 05

Emerson . . . . . . . . . . . . . . . . . . . . . . . 01

Fisher . . . . . . . . . . . . . . . . . . . . . . . . . 06

Genexxa . . . . . . . . . . . . . . . . . . . . . . . 07

Hitachi . . . . . . . 01, 07, 08, 09, 10, 11, 12

JVC. . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Kenwood . . . . . . . . . . . . . . . . . 06, 14, 15

Krell . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Magnavox . . . . . . . . . . . . . . . . . . . . . . 02

Marantz. . . . . . . . . . . . . . . . . . . . . 02, 03

MCS . . . . . . . . . . . . . . . . . . . . . . . . . . 03

Mission . . . . . . . . . . . . . . . . . . . . . . . . 03

NSM . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Onkyo . . . . . . . . . . . . . . . . . . . . . . . . . 16

Optimus . . . . . . . . . . . . . . . . . . 05, 07, 17

Panasonic . . . . . . . . . . . . . . . . . . . . . . 03

Philips. . . . . . . . . . . . . . . . . . . . . . . . . 02

Pioneer . . . . . . . . . . . . . . . . . . . . . 07, 17

Proton. . . . . . . . . . . . . . . . . . . . . . . . . 02

QED . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Quasar . . . . . . . . . . . . . . . . . . . . . . . . 03

RCA . . . . . . . . . . . . . . . . . . . . . . . 01, 21

Realistic . . . . . . . . . . . . . . . . . . . . . . . 01

Rotel . . . . . . . . . . . . . . . . . . . . . . . . . . 02

SAE . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Sansui. . . . . . . . . . . . . . . . . . . . . . . . . 02

Scott . . . . . . . . . . . . . . . . . . . . . . . . . . 01

Sony . . . . . . . . . . . . . . . . . . . . . . . 05, 18

Technics . . . . . . . . . . . . . . . . . 03, 19, 20

Victor. . . . . . . . . . . . . . . . . . . . . . . . . . 13

PERSONAL VIDEO

RECORDER BRAND . . . . . . . . . . CODE

Tivo. . . . . . . . . . . . . . . . . . . . . . . . . . . 01

Replay. . . . . . . . . . . . . . . . . . . . . . . . . 02

THE REMOTE CONTROL

Page 45

OSD

1. Press MENU on the remote control to display the different features on your HITACHI Projection TV.

2. Press the THUMB STICK to highlight a different feature.

3. Press EXIT on the remote control to quickly exit from a menu.

4. Press A/V Net on the remote control to access the A/V Net menu to control external components.

5. Press THUMB STICK  or  to access Favorite Channels menu.

A/V Net

EXIT

SELECT

Setup

Locks

Aspect

Audio

Video

Move

SEL

Sel

Ch. Manager

This part of the screen shows which selections are available.

This part of the screen shows which Remote Control buttons to use.

ON-SCREEN DISPLAY

Page 46

OSD

Picture Mode Select between the two picture modes; Day

and Night. Contrast Adjust contrast. Brightness Adjust brightness. Color Adjust color. Tint Adjust tint. Sharpness Adjust sharpness. Color Temperature Set this to High for less intense color with more blue, set to Medium

for natural color, set to Standard for standard colors or Black and

White for more reddish color. Black Enhancement Adjust shadow detail in dark screens. Edge Enhancement Automatically enhances the edges between light and dark areas. Reset Video Settings Choose the Reset Video settings. Color Management Adjust and balance individual colors to make either deeper or more

pure according to preference. Color Decoding Adjust the percentage of Red, Green and Color according to

preference. Auto Color

The AUTO COLOR function automatically monitors and adjusts the

color to maintain constant color levels even after a program or channel

changes. It also maintains natural flesh tones while preserving fidelity

of background colors. Noise Reduction Reduces conspicuous noise in the picture. Auto Movie Mode Turn ON/OFF the 3:2 Pulldown detection feature.

Treble Adjust the treble. Bass Adjust the bass. Balance Adjust the balance. Sound Enhancement Select SRS and BBE settings. Audio Source Select between three Audio Sources. Internal Speakers Select internal or external speakers. Auto Noise Cancel Eliminates the noise between stations. Perfect Volume Adjust volume in fixed setting. Loudness Adjust Loudness.

Mode Choose the picture format aspect ratio.

Ant A View/edit Channel ID, Scan, and Lock settings in antenna A. Ant B View/edit Channel ID, Scan, and Lock settings in antenna B.

Change Access Code Change Lock access code. Engage Lock Choose to lock channel, video input, and front panel. TV Time Lock Set specific time to Lock TV. Movie Ratings Block various types of movies and video types based on motion

picture ratings. TV Ratings Block various types of movies and television programming based on a

parental guide ratings. Canadian Ratings (ENG) Block various types of movies and television programming based on

the Canadian ratings system. Canadian Ratings (FRN) Block various types of movies and television programming based on

the Canadian French ratings system. Magic Focus Tune Up Automatic and manual alignment of the red, green and blue colors to

make white. Menu Preference Choose English, French, or Spanish text. Set The Clock Set the TV clock. It must be set before using the Lock feature. Set The Inputs Label Video Inputs , VCR, DVD, etc. Set The Color System Set tint and color coordinates for DTV programs. Set Virtual HD Select between 1080i and 540p signal. Set Black Side Panel Set the gray side bars on/off when watching 4:3 signals in

standard mode. Set Event Timer Turn TV on and off once, daily, or weekly. Set Closed Captions Feature to display dialogue/text. About Your TV Information display for this TV.

Video

ON-SCREEN DISPLAY

Aspect

Channel Manager

Audio

Locks

Setup

Page 47

VIDEO

ON-SCREEN DISPLAY

THUMB

STICK

SELECT

Color

Brightness

Contrast

Picture Mode

Video

Move

SEL

Select

Color Temperature

Sharpness

Tint

Reset Video Settings

Edge Enhancement

Setup

Locks

Aspect

Audio

Video

Move

SEL

Sel

Black Enhancement

Ch. Manager

100%

50% 50%

50% High

ANT A/B

High High

Day Night

SEL

Select

Picture Mode Day

Night

Return

Next/Prev

THUMB

STICK

THUMB

STICK

Select VIDEO to adjust picture settings and improve picture quality. You can customize each of the Video Inputs to your preference to increase viewing performance and pleasure depending upon the video program being viewed. If RESET is selected, only the selected mode will reset to initial conditions.

Video

Use THUMB STICK  or  to highlight Picture Mode settings.

Press EXIT to quit menu or select PICTURE MODE to return to previous menu.

Use this function to choose from automatic picture settings to optimize your TV’s performance.

Picture Mode

Function Day Night Reset

Contrast 100% 50% Brightness 50% 50% Color 50% 45% Tint Center Center Sharpness 50% 50% Color Temperature High Standard Black Enhancement High Low Edge Enhancement High Low Auto Color Off Off Noise Reduction Off Off Color Management Off Off

(Set User Colors) Auto Movie Mode Off Off

(TV/Cinema Detection)

Reset the video menu settings on current input to the Day or Night conditions depending on the selected VIDEO mode.

Page 48

VIDEO

ON-SCREEN DISPLAY

Use this function to change the contrast between black and white levels in the picture.

Use the THUMB STICK  or  to highlight the function to be adjusted. Press down on THUMB STICK to select the function settings. Press the THUMB STICK  or  to adjust the function. Press MENU to return to main menu. Press EXIT to quit menu.

Use this function to adjust the level of color in the picture.

Use this function to adjust overall picture brightness.

Set this to High for cooler color with more blue, set to Medium for more natural color, set to Standard for accurate color or set to Black/White for more reddish color.

Contrast

Color

Brightness

Color Temperature

NOTES: 1. If CONTRAST is selected, you are adjusting CONTRAST. The additional menu items BRIGHTNESS, COLOR, TINT,

and SHARPNESS can be selected and adjusted in the same manner.

2. It may be necessary to adjust TINT to obtain optimum picture quality when using the COMPONENT VIDEO Y-PBP

input jacks.

Use this function to adjust flesh tones so they appear natural.

Tint

Use this function to adjust the amount of fine detail in the picture. Sharpness function will be disabled when Noise Reduction is ON.

Sharpness

Use this function to automatically enhance the edges between light and dark areas using the settings Off, Low, Middle and High.

Edge Enhancement

THUMB

STICK

SELECT

Color

Brightness

Contrast

Picture Mode

Video

Move

SEL

Select

Color Temperature

Sharpness

Tint

Reset Video Settings

Edge Enhancement

Setup

Locks

Aspect

Audio

Video

Move

SEL

Sel

Black Enhancement

Ch. Manager

100%

50% 50%

50%

High

ANT A/B

High High

Day Night

Use this function to enhance the shadow detail in dark scenes using the settings off, low, middle and high.

Black Enhancement

Page 49

VIDEO

ON-SCREEN DISPLAY

This function allows you to Reset the Video Menu Settings of the present input and return it to the Day or Night conditions depending on the selected VIDEO mode.

Use THUMB STICK to highlight functions. Press down on THUMB STICK to select Reset Video Settings.

Use THUMBSTICK  to access other video settings. You can customize each of the Video Inputs to your preference to increase viewing performance and pleasure, depending upon the

video program being viewed. If RESET is selected, only the selected mode will reset to the initial conditions as explained above . If RESET is selected in Video:1 mode, only Video:1 mode will return to factory conditions.

Reset Video

Settings

THUMB

STICK

SELECT

THUMB

STICK

SELECT

100%

50%

High

Day Night

ANT A/B

High High

Move

SEL

Return

Select “Reset” to Return the Video menu Settings on this input to the original factory settings.

Reset

Color

Brightness

Contrast

Picture Mode

Video

Move

SEL

Select

Color Temperature

Sharpness

Tint

Reset Video Settings

Edge Enhancement

Black Enhancement

Reset Video Settings

Video

100%

50% 50%

50%

High

Day Night

ANT A/B

High High

Color

Brightness

Contrast

Picture Mode

Video

Move

SEL

Select

Color Temperature

Sharpness

Tint

Reset Video Settings

Edge Enhancement

Black Enhancement

THUMB

STICK

SELECT

THUMB

STICK

Off

ANT A/B

Off Off

Noise Reduction

Auto Color

Color Decoding

Color Management

Video

Move

SEL

Select

Auto Movie Mode

Use this function to adjust and balance the listed individual colors to make them either deeper or more pure depending on the user’s preference.

Color Management

Use THUMBSTICK to highlight function. Press down to select the User Colors setting. When the function has a “” in the box, it is ON. Press THUMBSTICK , , , , to highlight and adjust individual colors. Use THUMBSTICK to highlight and select “Reset” to return all colors to default settings.

NOTE: When the Set User Colors box is not checked off, the listed colors will be grayed out.

Video

Color Management

Color Decoding Auto Color Noise Reduction Auto Movie Mode

Move

Video

Color Management

Set User Colors Magenta 50% Red 50% Yellow 50% Green 50% Cyan 50% Blue 50%

Reset

SEL

Move

SEL

Select

ANT A/B

Off Off Off

THUMB

STICK

Return

Page 50

VIDEO

ON-SCREEN DISPLAY

Use this function to adjust the percentage of Red, Green and Color according to the user’s preference. Use TINT to adjust flesh tones so they appear natural.

Color Decoding

The AUTO COLOR function automatically monitors and adjusts the color to maintain constant color levels even after a program or channel changes. It also maintains natural flesh tones while preserving fidelity of background colors.

The NOISE REDUCTION function automatically reduces conspicuous noise in the picture without degrading picture quality. Set NOISE REDUCTION to OFF if the TV experiences picture blocking. When Noise Reduction is ON, Sharpness function is disabled (grayed out).

The Auto Movie Mode function turns ON or OFF the 3:2 PULLDOWN DETECTION SPECIAL FEATURE. Theatrical movies are shot on film at 24 frames or still pictures per second, instead of 30 frames or 60 fields like video. When film is transferred to video for television viewing, the disparity between the two frame rates must be reconciled. This involves a process known as 3:2 pulldown.

When Auto Movie Mode is turned ON from the VIDEO menu, your Hitachi Projection Television will activate the circuitry for this special feature to improve video performance when watching film based sources.

Use THUMBSTICK to highlight function. Press down to select from 4 menu items. Press THUMBSTICK , , , , to highlight and adjust Red, Green, Color and Tint. Use THUMBSTICK to highlight and select “Reset” to return all settings to default.

NOTE: When using Component or DVI-HDTV input, Auto Color will not be available (grayed out).

NOTES: 1. When using Progressive Scan Component or DVI-HDTV input (Ex. 480p, 720p), Auto Movie Mode will not be

available (grayed out).

2. All Video settings are independent of each other based on it’s input (ANTA/B, Input 1~5).

Auto Color

Noise Reduction

Auto Movie Mode

NOTE: Color Decoding settings are independently stored in each of the 4 Color Temperature settings.

Video

Color Management

Color Decoding

Auto Color Noise Reduction Auto Movie Mode

Move

ANT A/B

Off Off

SEL

Select

Off

THUMB

STICK

Video

Color Decoding

RGB R G B Red 50% Green 50% Color 50% Tint

Reset

Move

SEL

Return

Page 51

ON-SCREEN DISPLAY

AUDIO

Select AUDIO to adjust the TV to your preference and to improve the sound quality.

Audio

THUMB

STICK

SELECT

Sound Enhancement

Balance

Bass

Treble

Audio

Move

SEL

Return

Internal Speakers

Audio Source

Perfect Volume

Auto Noise Cancel

50%

Off

Locks

Chan. Manager

Aspect

Audio

Video

Move

SEL

Sel

Setup

On On

45%

Stereo

THUMB

STICK

Loudness

This function controls the low frequency audio to all speakers.

Press THUMB STICK , , to select menu item. Press THUMB STICK  or  to adjust the function. Press EXIT to quit the MENU, or select Audio to return to the main menu.

NOTE: If TREBLE is selected you are adjusting treble. The additional menu items Bass and Balance can be selected and

adjusted in the same manner.

This function controls the high frequency audio to all speakers.

This function will control the left to right balance of the Projection TV internal speakers.

Bass

Balance

Treble

Multi-Channel Television Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural sound) used when receiving a weak stereo broadcast or 2nd Audio Prog (SAP) which may be a secondary language, weather report, etc. The sources received will be displayed at the top right edge of the TV. The source you select will be displayed above the sources received. See example below for each selection when both stereo and second audio are received (monaural is always received).

This function is useful when setting up the external speakers. ON - Select this feature if using the internal speakers only. TV as Center - Select this feature when setting up external speakers from a separate stereo system. The

TV’s speakers will work as the center speaker.

OFF - Select this feature if you prefer to use only speakers from a separate stereo system. This function eliminates the noise between stations. If a channel is tuned and is noisy, this function will

automatically eliminate the audio for that channel.

This function will automatically adjust volume so each channel and input has the same average volume level.

This function turns loudness ON or OFF. It will improve the quality of both low and high frequency sounds when listening at low volume levels.

STEREO SELECTED

SAP SELECTED

MONO SELECTED

3:32 PM

Ant A 10

Stereo

3:32 PM

Ant A 10

SAP

3:32 PM

Ant A 10

Mono

Audio Source

Internal Speakers

Auto Noise Cancel

Perfect Volume

Loudness

Sound Enhancement

See page 52.

Page 52

AUDIO

ON-SCREEN DISPLAY

Sound Enhancement

The following surround settings will reproduce the “live” sound you would hear in concert halls, sports stadiums, movie theaters, etc. with only two speakers.

THUMB

STICK

SELECT

Sound Enhancement

Balance

Bass

Treble

Audio

Move

SEL

Return

Internal Speakers

Audio Source

Perfect Volume

Auto Noise Cancel

50%

SRS

Off

Locks

Chan. Manager

Aspect

Audio

Video

Move

SEL

Sel

Setup

Off Off

45%

Stereo

THUMB

STICK

Loudness

To enter SOUND ENHANCEMENT, use THUMB STICK  or  to highlight then press THUMB STICK  to select SOUND ENHANCEMENT of your choice (Off, SRS, BBE and SRS and BBE).

Use the THUMB STICK to highlight your sound enhancement choice, and press SELECT to select your choice.

Based on the principles of the human hearing system, SRS technology delivers and exciting and realistic 3D Sound experience from just two external speakers (or) the two internal speakers of your HITACHI Television. If your HITACHI Television is connected to an external audio system, SRS will also create an incredible 3D sound experience from two speakers and even enhance a complete multi-speaker surround sound system.

Technology

Sound reproduction quality enhancement system. The BBE technology produces sound that is natural and crisp from just two speakers (or) the two internal speakers of your HITACHI television. If your HITACHI television is connected to an external audio system, BBE will also create an incredible crisp sound experience from two speakers and even more complete and accurate reproduction of the original performance. BBE brings to the listener’s ear a more complete and accurate reproduction of the original performance. Each voice, speaking or singing, each instrument or sound effect is presented with its attendant harmonics or partials more clearly audible. The ear can then more easily recognize the unique tonal colors of each sound as though the sound was being produced live.

NOTES:

*SRS and the symbol are registered trademarks of SRS Labs, Inc. SRS technology is incorporated under license

from SRS Labs, Inc.

NOTES:

Licensed by BBE Sound, Inc. under USP4638258 and 4482866. BBE and BBE symbol are registered trademarks of BBE

Sound, Inc. Manufactured under license from BBE Sound, Inc.

Page 53

ON-SCREEN DISPLAY

ASPECT MODE

Aspect Mode

Auto Aspect

Automatically adjust the Aspect Ratio depending on the input signal to fill the screen.

Press THUMB STICK , , to select menu item. Press down on THUMBSTICK to select. A“” in the box indicates that the feature is ON.

Vertical Position

This function allows you to select when aspect style is either 4:3 EXPANDED/ZOOM1/ZOOM2 or 16:9 ZOOM. Vertical position can be changed with these modes. For example, it will be useful for centering the picture area at both the top and bottom of the picture with 480i/480P signal. Adjustable range is -10 (video center is toward bottom of screen) to +10 (video center is toward top of screen).

Press THUMB STICK , , to select menu item. Press THUMB STICK  or  to adjust the function. Press EXIT to quit the MENU, or select Aspect to return to the main menu.

Use this function to select the Picture Format Aspect Ratio.

NOTES: 1. The Auto Aspect function is recommended on an input signal with VIDEO ID.

2. The Auto Aspect function is best used on component video, S-Video, and 480i component signals.

3. See page 31 for Aspect Mode availability.

NOTE: Vertical Position will not be available in 4:3 Standard and 16:9 Standard modes.

Page 54

ON-SCREEN DISPLAY

CHANNEL MANAGER

Select ANTENNAif you are using an indoor or outdoor antenna. Select Cable if you have cable TV.

Use THUMB STICK  ,  to highlight the correct Channel Source. Press the THUMB STICK to select highlighted source. Press EXIT to quit the menu.

Reception channels for each mode are shown at the left.

Refer to your cable or TV guide for channel identification standards.

Chan. Manager

Move

SEL

Return

Channel Source Antenna Cable(1) Cable(2)

Auto Channel Scan

Start

THUMB

STICK

SELECT

THUMB

STICK

Move

SEL

Select

Channel Source

Antenna

Cable(1) Cable(2)

Auto Channel Scan

Start

Ant. B

Chan. Manager

Move

SEL

Select

Ant. A

Channel List

Chan. Manager

Ant. A

Channel List

Chan. Manager

Ant. A

THUMB

STICK

RECEPTION BAND

CATV 1 OR CATV 2

AIR

VHF 2 ~ 13ch

UHF 14 ~ 69ch

CATV CHANNEL

VHF 2~13

Mid band A~1

A-5 ~ A-1

Super band J~W

Hyper band

W + 1 ~ W + 28

Ultraband

W + 29 ~ W + 84

Indicated on

the screen

2 ~ 13

14 ~ 22 95 ~ 99

23 ~ 36 37 ~ 64

65 ~ 125

NOTE:

If certain CATV channels are poor or not possible in Cable(1) mode, select Cable(2).

Page 55

CHANNEL MANAGER

ON-SCREEN DISPLAY

This feature will automatically store active TV channels in Auto Channel Scan. This will allow you to skip unused channels when using CHANNEL UP () or DOWN ().

If the EXIT button is pressed while AUTO CHANNEL SCAN function is engaged, programming will stop. If two antennas are connected, switch antenna inputs and repeat AUTO CHANNEL SCAN for the second antenna input.

Remember to select the correct ANTENNA/CABLE mode before using AUTO CHANNEL SCAN. See CHANNEL MANAGER - SCAN to add or to erase additional channels.

Auto Channel Scan

THUMB

STICK

SELECT

THUMB

STICK

SEL

Cancel

Scanning Channel Number: 66

Move

SEL

Select

Channel Source

Auto Channel Scan

Start

Chan. Manager

Ant. A

Channel List

Antenna Cable(1) Cable(2)

Move

SEL

Select

Channel Source

Auto Channel Scan

Start

Chan. Manager

Ant. A

Channel List

Antenna Cable(1) Cable(2)

Chan. Manager

Ant. A

Auto Channel Scan

Page 56

CHANNEL MANAGER

ON-SCREEN DISPLAY

Press THUMB STICK  or  to review more channels. Press EXIT to quit the menu.

THUMB

STICK

SELECT

Move

SEL

Return

Ch# Scan CH ID Lock

2 Off -------3 Off -------4 Off -------5 Off -------6 Off -------7 Off -------8 Off -------9 Off --------

Chan. Manager

Channel List

Move

SEL

Select

Channel Source

Auto Channel Scan

Start

Chan. Manager

Ant. A

Channel List

Antenna Cable(1) Cable(2)

This function allows you to review which channels are labeled (CH ID), which have been added to Channel Memory (SCAN), and which are protected by LOCK.

Channel

List

Use this feature after Auto Channel Scan is completed to add (On) or skip (Off) additional channels to the remote control channel  or  buttons.

Scan

To add (Scan-On) or skip (Scan-Off) additional channels while in Channel Manager, THUMB STICK  to highlight the channel number, then THUMB STICK  or  to highlight other channels. Once the desired channel is highlighted, THUMB STICK  to scan column, then THUMB STICK  or  to select ON or OFF.

NOTE: Lock feature cannot be selected or set in CHANNEL MANAGER.

THUMB

STICK

Move

SEL

Return

Ch# Scan CH ID Lock

2 Off -------3 Off -------4 Off -------5 Off -------6 Off -------7 Off -------8 Off -------9 Off --------

Move

SEL



Ch# Scan CH ID Lock

Off -------3 Off -------4 Off -------5 Off -------6 Off -------7 Off -------8 Off -------9 Off --------

Move

Set

Ch# Scan CH ID Lock

Off

-------3 Off -------4 Off -------5 Off -------6 Off -------7 Off -------8 Off -------9 Off --------

Ch# Scan CH ID Lock

-------3 Off -------4 Off -------5 Off -------6 Off -------7 Off -------8 Off -------9 Off --------

THUMB

STICK

THUMB

STICK

[]

Move

Set

Tune

Chan. Manager

Ant. A

Chan. Manager

Ant. A

Chan. Manager

Ant. A

Chan. Manager

Ant. A

Time

Page 57

ON-SCREEN DISPLAY

CHANNEL MANAGER

This section contains advanced features which will make TV viewing easier and more enjoyable. Use this feature to give up to 20 channels a name when ANTENNA signal source is selected and up to 60 channels a name when CATV signal source is selected.

NOTES: 1. If ANTA and ANT B are in the same ANTENNA/CABLE mode, the CHANNEL ID for both antenna inputs will be the

same.

2. CHANNEL ID will not be displayed when PIP is ON.

Channel ID

Move

Edit (A-Z, 0-9, _, -)

Ch# Scan Ch ID Lock

2On-------3On-------4 Off -------5 Off -------6 Off -------7 Off -------8 Off -------9 Off --------

SEL

Return

Ch# Scan Ch ID Lock

2OnA------3On-------4 Off -------5 Off -------6 Off -------7 Off -------8 Off -------9 Off --------

Ch# Scan Ch ID Lock

2OnA------3On-------4 Off -------5 Off -------6 Off -------7 Off -------8 Off -------9 Off --------

THUMB

STICK

THUMB

STICK

THUMB

STICK

[]

Move

Edit (A-Z, 0-9, _, -)

SEL

Return

Move

Edit (A-Z, 0-9, _, -)

SEL

Return

Chan. Manager

Ant. A

Chan. Manager

Ant. A

Chan. Manager

Ant. A

Page 58

LOCKS

ON-SCREEN DISPLAY

This function will block out the picture and sound of the selected channel or video input. It can also be used to keep the TV from being viewed for a scheduled time period that you set.

The code to enter the Locks feature is a four digit secret code number. The factory preset code is 0000. Use the number buttons to select secret code.

Locks

Please Enter Access Code

[ - - - - ]

[# Keys] Enter Code

0000

THUMB

STICK

SELECT

Locks

Chan. Manager

Aspect

Audio

Video

Move

SEL

Sel

Setup

Movie Ratings

TV Time Lock

Engage Lock

Change Access Code

Locks

Move

SEL

Return

Canadian Ratings (Frn)

Canadian Ratings (Eng)

TV Ratings

NOTE: 1. If ANTA and ANT B are in the same signal source mode (see page 54), when a channel is locked, it is locked

on both antenna inputs.

2. When using TV TIME LOCK make sure the clock is set (see page 67).

3. Text appears on the screen to indicate that TV TIME LOCK is activated.

4. If MOVIE/TV Ratings Lock function settings are ON, SURF will be deactivated.

Use THUMB STICK  or  to highlight function and then press SELECT button. To change the secret code number, select Change Access Code. Enter a new four digit key number you prefer.

Select CHANGE ACCESS CODE to change the factory preset code (0000) to your preference. When ENGAGE LOCK is selected, SET CHANNEL LOCK, SET INPUT LOCK, and SET FRONT PANEL LOCK can be set individually.

When SET CHANNEL LOCK is turned on, the picture and sound for the chosen channel will be blocked out. When SET INPUT LOCK is turned on, the picture and sound for all video inputs and the picture and sound for channels 3, 4 will be

blocked out. When FRONT PANEL LOCK is turned on, all buttons on the Front Panel will be deactivated, except the Power button. When TV TIME LOCK is turned on (❒ TIME LOCK) you can set the BEGIN and END times (THUMB STICK ) and the TV

cannot be viewed during that time period (Set clock first). Use CURSOR  or  to highlight ONCE (TV will time out one time only), DAILY (TV will time out every day), WEEKLY (TV will time out one time a week).

When MOVIE RATINGS is selected, you can block various types of movies and video tapes based on motion picture ratings. Picture in-Picture will also be blocked automatically (see page 59).

When TV RATINGS is selected, various types of television programming based on a parental guide ratings will be blocked. Picture-in-Picture will also be blocked automatically (see page 60).

Use CANADIAN RATINGS to block various types of movies and television programs based on the two rating systems used in Canada that you feel may be inappropriate due to its content (see pages 61-62).

If you forget your secret code, use the factory code 7777 to erase your key number. This will reset the secret code number back to the factory preset 0000. Press EXIT to quit the menu.

✔

Page 59

LOCKS

ON-SCREEN DISPLAY

Use MOVIE RATINGS to prevent viewing of any movie that you feel may be inappropriate due to its content.

Use THUMB STICK  or  to select the MOVIE RATING category that you want to block. Press SELECT to block the MOVIE RATING that you have selected. Once rating is selected, for example PG-13, all movies rated PG-13 and higher (R, NC-17, and X) will be blocked. Press EXIT to quit the menu or select MOVIE RATINGto return to the previous menu.

Movie Ratings

THUMB

STICK

SELECT

Locks

Move

SEL

Return

Movie Ratings

TV Time Lock

Engage Lock

Change Access Code

Locks

Status

TV Ratings

Move

SEL

Select

Canadian Ratings (Eng) Canadian Ratings (Frn)

Not Rated:

PG:

PG-13:

NC-17:

THUMB

STICK

Contains no rating. Not Rated (NR) and Not Applicable (NA) programs. Movie has not been rated or

ratings do not apply.

Restricted. Under 17 requires accompanying parent or adult guardian.

Parents strongly cautioned. Some material may be inappropriate for children under 13.

Parental guidance suggested. Some material may not be suitable for children.

General audiences. All ages admitted.

Adults only

No one 17 and under admitted.

PG-13

NC-17

NOT RATED (NR)

Motion Picture Ratings Chart

Page 60

LOCKS

ON-SCREEN DISPLAY

TV Ratings

THUMB

STICK

SELECT

Locks

Move

SEL

Return

TV Ratings

Movie Ratings

TV Time Lock

Engage Lock

Change Access Code

Locks

Status

TV Ratings

Move

SEL

Select

Canadian Ratings (Eng) Canadian Ratings (Frn)

TV-Y:

TV-Y7:

TV-G: TV-PG: TV-14: TV-MA:

THUMB

STICK

Sub Rating

DL S VFV

TV Parental Guide Ratings Chart

Use TV RATINGS to prevent the viewing of any TV program that you feel may be inappropriate due to its content.

Use THUMB STICK  or  to highlight the category that you want to block. Press select to block the TV RATINGS that you have selected.

Press EXIT to quit the menu or select TV RATINGS to return to the previous menu.

Parental guidance suggested. The program may contain infrequent coarse language, limited violence, some suggestive sexual dialogue and situations.

Directed to older children. Themes and elements in this program may include mild physical or comedic violence, or may frighten children under the age of 7.

All children. The themes and elements in this program are specifically designed for a very young audience, including children from ages 2-6.

General audience. It contains little or no violence, no strong language, and little or no sexual dialogue or situations.

TV-Y

TV-Y7

TV-G

TV-PG

TV-14

TV-MA

Parents strongly cautioned. This program may contain sophisticated themes, intense sexual situation, more intense violence and intensely suggestive dialogue.

Mature audiences only. This program may contain mature themes, indecent language, graphic violence, and explicit sexual content.

Fantasy Violence

Violence

Sexual Situation

Adult Language

Sexually Suggestive Dialogue.

L D

NOTE:

If you Block TV-14D, you will still permit TV MA programs; If you block TV-14DV, you will automatically block TV-MAV programs, but you will still permit TVMALS programs. This means that the TV will block violence in TV-14 and higher (TV-MA), but not language and sex.

N/A

None.

Page 61

LOCKS

ON-SCREEN DISPLAY

Canadian Ratings

(Eng)

THUMB

STICK

SELECT

Locks

Move

SEL

Return

Canadian Ratings (Eng)

Movie Ratings

TV Time Lock

Engage Lock

Change Access Code

Locks

Status

TV Ratings

Move

SEL

Select

Canadian Ratings (Eng)

Canadian Ratings (Frn)

C8+:

PG: 14+: 18+:

THUMB

STICK

Canadian Ratings English Chart

Use Canadian Ratings (Eng) to block any type of movie and television program in Canada that you feel might be inappropriate in its content.

Use THUMB STICK  or  to select the CANADIAN RATINGS (Eng) category that you want to block. Press SELECT to set the CANADIAN RATINGS (Eng) that you have selected. Once rating is selected, for example C8+, all movies and television programs rated C8+ and higher (G, PG, 14+ and 18+) will be blocked automatically. Press EXIT to quit menu.

C8+

18+

14+

Programming intended for children under age 8 - Violence Guidelines; Careful attention is paid to themes, which could threaten children’s sense of security and wellbeing. There will be no realistic scenes of violence. Depictions of aggressive behaviour will be infrequent and limited to portrayals that are clearly imaginary, comedic or unrealistic in nature. Other Content Guidelines: There will be no offensive language, nudity or sexual content.

Programming generally considered acceptable for children 8 years and over to watch on their own - Violence Guidelines: Violence will not be portrayed as the pre-

ferred, acceptable, or only way to resolve conflict; or encourage children to imitate dangerous acts which they may see on television. Any realistic depictions of violence will be infrequent, discreet, of low intensity and will show the consequences of the acts. Other Content Guidelines: There will be no profanity, nudity or sexual content.

General Audience - Violence Guidelines: Will contain very little violence, either physical or verbal or emotional. Will be sensitive to themes which could frighten a younger child, will not depict realistic scenes of violence which minimize or gloss over the effects of violent acts. Other Content Guidelines: There may be some inoffensive slang, no profanity and no nudity.

Parental Guidance - Programming intended for a general audience but which may not be suitable for younger children. Parents may consider some content inappropriate for unsupervised viewing by children ages 8-13. Violence Guidelines: Depictions of conflict and/or aggression will be limited and moderate; may include physical, fantasy, or supernatural violence. Other Content Guidelines: May contain infrequent mild profanity, or mildly suggestive language. Could also contain brief scenes of nudity.

Programming contains themes or content which may not be suitable for viewers under the age of 14 - Parents are strongly cautioned to exercise discretion in permit-

ting viewing by pre-teens and early teens. Violence Guidelines: May contain intense scenes of violence. Could deal with mature themes and societal issues in a realistic fashion. Other Content Guidelines: May contain scenes of nudity and/or sexual activity. There could be frequent use of profanity.

Adult - Violence Guidelines: May contain violence integral to the development of the plot, character or theme, intended for adult audiences. Other Content Guidelines: May contain graphic language and explicit portrayals of nudity and/or sex.

Page 62

ON-SCREEN DISPLAY

LOCKS

Canadian Ratings

(Frn)

THUMB

STICK

SELECT

Locks

Move

SEL

Return

Canadian Ratings (Frn)

Movie Ratings

TV Time Lock

Engage Lock

Change Access Code

Locks

Status

TV Ratings

Move

SEL

Select

Canadian Ratings (Eng)

Canadian Ratings (Frn)

8 ans+: 13 ans+: 16 ans+: 18 ans+:

THUMB

STICK

Canadian Ratings French Chart

Use CANADIAN RATINGS (FRN) to block Canadian French programs according to various program ratings that you feel might be inappropriate in its content.

Use THUMB STICK  or  to highlight the category that you want to block. Press SELECT to set the CANADIAN RATINGS (FRN) that you have selected. Once rating is selected, for example 8 ans+, all movies and television programs rated 8 ans+ and higher will be

automatically blocked.

Press EXIT to quit menu or select THUMB STICK  to return to the previous menu.

8 + General - Not recommended for young children - Programming intended for a broad

audience but contains light or occasional violence that could disturb young children. Viewing with an adult is therefore recommended for young children (under the age of 8) who cannot differentiate between real and imaginary portrayals.

General - Programming intended for audiences of all ages. Contains no violence, or the violence content is minimal or is depicted appropriately with humor or caricature or in an unrealistic manner.

Programming restricted to adults - Contains constant violence or scenes of extreme violence.

Programming is not suitable for children under the age of 16 - Contains frequent scenes

of violence or intense violence.

8 ans +

13 ans +

16 ans +

18 ans +

Programming may not be suitable for children under the age of 13 - Contains either a

few violent scenes or one or more sufficiently violent scenes to affect them. Viewing with an adult is therefore strongly recommended for children under 13.

Page 63

SETUP

ON-SCREEN DISPLAY

Select SETUP when setting your TV up for the first time. Use the THUMB STICK  or  on the remote to highlight the function desired.

Setup

Locks

Aspect

Audio

Video

Move

SEL

Sel

Set The Clock

Magic Focus Tune Up

Setup

Set The Inputs

Move

SEL

Return

Set The Color System Set Virtual HD

THUMB

STICK

THUMB

STICK

SELECT

Set Black Side Panel

Ch. Manager

Menu Preference

Set Event Timer Set Closed Caption About Your TV

Use THUMB STICK  or  to select the sub-menu of your choice.

Page 64

SETUP

ON-SCREEN DISPLAY

MAGIC

FOCUS

MAGIC FOCUS

Auto Digital Convergence Adjustment

Please turn ON your television for at least 20 minutes before using this feature. The Magic Focus button on control panel will not work when adjustment mode is set to Manual (see page 65). Your HITACHI Projection TV has three color projection tubes: one for red, one for green, one for blue. When mixed together in the

proper proportion, the output of these three color tubes can produce any color. To produce these colors, however, the beams must be precisely aligned over each other so that the colors can be mixed. The process of aligning these picture beams is called “convergence”.

Over a period of time, the picture tubes can drift out of alignment due to normal bumps and vibrations or moving the TV. If you move your TV, or if, after a time, you notice color rings or halos around objects in the picture, you may want to converge (align) the colors.

Properly converged, the lines appear white, which is actually a combination of the outputs of the three color tubes. The output of the green tube is stationary. The outputs of the red and blue tubes can be adjusted. When properly aligned, the outputs of all three tubes should be directly over each other to produce the white lines.

To simplify convergence, HITACHI incorporates a function called MAGIC FOCUS located on the front control panel, which allows the TV to self-adjust. Press this MAGIC FOCUS button and the convergence self adjustment will start and this process will take approximately 20 seconds. If this button is pressed during this process, no change in picture quality will occur. After this 20 second self-adjust period, picture quality will be optimum. (Do not move the TV during self-adjust.)

You may also select MAGIC FOCUS TUNE UP from the Setup Menu.

Magic Focus

Tune Up

NOTES: Only a momentary press of the MAGIC FOCUS button is necessary to start AUTO DIGITAL CONVERGENCE. At any

time during this convergence correction process, you may press the MAGIC FOCUS button to exit the MAGIC FOCUS mode. However, the convergence correction process needs to be completed to SAVE the new corrected convergence data.

Magic Focus Tune Up

Setup

Move

SEL

Return

Aligns the Red, Green, and Blue colors to correct for Magnetic Influences.

Auto At turn off (after 90 days) Manual

THUMB

STICK

THUMB

STICK

SELECT

Setup

Locks

Ch. Manager

Aspect

Video

Move

SEL

Sel

Set The Inputs

Set The Clock

Menu Preference

Magic Focus Tune Up

Setup

Move

SEL

Select

Set Black Side Panel

Set Virtual HD

Set The Color System

THUMB

STICK

SELECT

Adjustment Mode

If you want to adjust now

THUMB

STICK

THUMB

STICK

SELECT

Start

MAGIC FOCUS

Audio

About Your TV

Set Closed Caption

Set Event Timer

Page 65

SETUP

ON-SCREEN DISPLAY

NOTES: 1. Please turn ON your television for at least 20 minutes before using this feature.

2. Auto Adjustment Mode is recommended. If convergence is still not acceptable, use the Manual Adjustment Mode. DO NOT press MAGIC FOCUS or use Auto Adjustment Mode after using Manual Adjustment Mode.

Manual Convergence Adjustment Mode

Using the Remote Control, select SETUP-MAGIC FOCUS TUNE UP-MANUAL ADJUSTMENT MODE-START to access convergence crosshatch pattern. The adjustment point is indicated by the Adjustment Point Cursor.

To Move Adjustment Point

To move the adjustment point cursor using the THUMBSTICK, the Adjustment Cursor must be WHITE. Another way to move the Adjustment Point Cursor is to press the following buttons: [2] up, [4] left, [5] down, [6] right. If you use the number buttons while the adjustment point is WHITE, it will change to RED.

To Change the Color of Adjustment Point

Press the SELECT button repeatedly (WHITE-RED-BLUE-WHITE...). Green color is fixed and cannot be adjusted.

To Adjust the Convergence

Move the Adjustment Cursor to the point to be adjusted. Use the THUMB STICK to match the RED and BLUE colors to GREEN (reference color). Properly aligned, all three colors should appear white.

If convergence is acceptable after Manual Convergence adjustment, press EXIT button to access menu mode.

Press the [0] button on the remote control to CANCEL adjusted data and return to main picture. Press the [1] button on the remote control to SAVE adjusted data and return to main picture. Press the [2] button on the remote control to return to the manual convergence adjustment mode (crosshatch pattern). Press the [3] button on the remote control to recall the factory pre-set convergence data. Press the [9] button on the remote control to read the SAVED adjusted data. If there is no saved data, pressing the [9] button will recall the factory pre-set data.

THUMB

STICK

THUMB

STICK

SELECT

Setup

Locks

Ch. Manager

Aspect

Video

Move

SEL

Sel

THUMB

STICK

SELECT

Audio

Magic Focus Tune Up

Setup

Move

SEL

Return

Aligns the Red, Green, and Blue colors to correct for Magnetic Influences.

Auto At Turn Off

(After 90 Days)

Manual

Adjustment Mode

If you want to adjust now

THUMB

STICK

THUMB

STICK

SELECT

Start

Adjustment Point

Cursor

Set The Inputs

Set The Clock

Menu Preference

Magic Focus Tune Up

Setup

Move

SEL

Select

Set Black Side Panel

Set Virtual HD

Set The Color System

About Your TV

Set Closed Caption

Set Event Timer

EXIT

117 Manual Adjust Please Enter Number.

0.Cancel and go to Normal Mode.

1.Done and go to Normal Mode.

2.Back to Adjust Mode

3.Factory Reset and Back to Adjust Mode.

0-3.Select

Page 66

SETUP

ON-SCREEN DISPLAY

This feature will allow you to select any one of three different languages for all on-screen displays.

Use THUMB STICK  ,  to highlight the language of your choice. Press SELECT to select the highlighted language. Press EXIT to quit menu or select MENU PREFERENCE to return to previous menu.

Menu Preference

THUMB

STICK

SELECT

Setup

Move

SEL

Return

Menu Preferences

Set The Language English Francais Español

Set The Menu Background Shaded Solid

THUMB

STICK

Setup

Move

SEL

Select

Menu Preferences

Set The Language

English

Francais Español

Set The Menu Background Shaded Solid

THUMB

STICK

Set The Inputs

Set The Clock

Menu Preference

Magic Focus Tune Up

Setup

Move

SEL

Select

Set Black Side Panel

Set Virtual HD

Set The Color System

About Your TV

Set Closed Caption

Set Event Timer

Page 67

SETUP

ON-SCREEN DISPLAY

The clock must be adjusted before you can use the “Set Event Timer” or “TV Time Out” features.

Use THUMB STICK  or  to set the time and date. Press THUMB STICK  or  to change position. Press EXIT to quit menu.

Set The Clock

THUMB

STICK

SELECT

Setup

Move

SEL

Return

Set The Clock

Time : 03:57 PM Apr 29, 2003

Setup

Move

SEL

Return

Set The Clock

THUMB

STICK

Set The Inputs

Set The Clock

Menu Preference

Magic Focus Tune Up

Setup

Move

SEL

Select

Set Black Side Panel

Set Virtual HD

Set The Color System

About Your TV

Set Closed Caption

Set Event Timer

Time : 03:57 PM Apr 29, 2003

Setup

Move

SEL

Return

Set The Clock

Time : 03:57 PM Apr 29, 2003

THUMB

STICK

Set

This function allows you to choose from two menu backgrounds.

Use THUMB STICK  ,  to highlight SET THE MENU BACKGROUND (shaded or solid), and press down on THUMB STICK to select setting. Press EXIT to quit menu or THUMB STICK  to return to previous menu. Select SOLID for a black background (no picture can be seen behind menu screen), or select SHADED for a light background.

Menu Background

THUMB

STICK

Setup

Move

SEL

Select

Menu Preferences

Set The Language

English

Francais Español

Set The Menu Background Shaded Solid

Page 68

SETUP

ON-SCREEN DISPLAY

Use this feature to give a name to any of the five video inputs.

Press THUMB STICK , , , , to highlight the name of the video inputs. Press down on THUMB STICK to select desired input name.

Select RESET to set video names to original factory preset condition.

Set The Inputs

THUMB

STICK

SELECT

Setup

Move

SEL

Return

Set The Inputs

Video1 Video2 Video3 Video4 Video5

Set The Clock

Magic Focus Tune Up

Setup

Set The Inputs

Move

SEL

Select

Set The Color System Set Virtual HD

THUMB

STICK

Set Black Side Panel

Menu Preference

Set Event Timer Set Closed Caption About Your TV

Rename List

AVR DVD PVR2 VCR CAM DVD2 SAT VCR2 CBL LD STB CBL2 PVR STB2 Reset

Use this function to automatically turn the TV on and tune to Video2 when it detects a video signal to input 2.

Use THUMB STICK , ,  or , then press down on THUMB STICK to change AUTO LINK setting. When AUTO is selected, the TV will turn on and tune to Video2 automatically, when the Video2 input device is turned on. This is con-

venient when you want to watch a movie with your VCR, laserdisc player, or DVD player. When REMOTE is selected, the TV will turn on and switch to Video2 automatically when the Video2 input device is turned on and the

VCR, laserdisc, or DVD play button on your remote control is pressed. This is convenient when you want to record a movie with your VCR and watch it later.

Select Off to disable this function. Press EXIT to quit menu.

Video 2 Auto Link

NOTES: 1. Once the TV has been turned on using the AUTO LINK feature, it must be reset before AUTO LINK is used again. To

do this, turn your VCR, laserdisc, or DVD player OFF. This feature is now reset and will turn on your TV as described above.

2. When using REMOTE mode, any remote control button will substitute for your video input device play button. However, intended operation is for use with your VCR, laserdisc, or DVD play button.

3. If no remote control button is pressed after the TV is turned on by AUTO LINK, the TV will automatically turn off after three hours.

Setup

Move

SEL

Return

Set The Inputs

Video1 Video2 Video3 Video4 Video5

Rename List

AVR DVD PVR2 VCR CAM DVD2 SAT VCR2 CBL LD STB CBL2 PVR STB2 Reset

Setup

Move

SEL

Return

Set The Inputs

Video1

Video2

Video3 Video4 Video5

Rename List

AVR DVD PVR2 VCR CAM DVD2 SAT VCR2 CBL LD STB CBL2 PVR STB2 Reset

Auto Link

Auto Remote Off

DVD

THUMB

STICK

Page 69

SETUP

ON-SCREEN DISPLAY

Set The Color

System

Set Virtual HD

Set Black Side

Panel

This function allows you to automatically change tint and color coordinates for DTV programs. HDTV - High Definition Television - Use for High Vision Signal Y-P

BPR

from HDTV Set-Top Box.

SDTV/DVD - Standard Definition Television or DVD (Digital Versatile Disc Player) Y-CBCR.

NOTES: 1. If Color System is set improperly (does not match actual input signal), the color and tint of the main picture will be

abnormal.

2. You must be tuned to VIDEO: 1 or 2 inputs and have a component hooked up to the Y-PBPRinput jacks to access this color system.

3. All component color type settings will affect only color component input you are currently viewing. If you are using both sets of component input jacks, be sure to set the color system feature for both inputs.

Use this feature to select between 1080i and 540p (see page 32).

The BLACK SIDE PANEL function turns the gray side bars on/off when watching 4:3 signals in Standard mode. The top/bottom gray bar will appear in SPLIT MODE PIP and SPLIT FREEZE.

NOTE: To maximize operating life of the TV’s picture tubes when watching 4:3 signal, Black Side Panel is cancelled at Power

OFF. It is recommended to watch 4:3 signal with gray side bar.

Page 70

SETUP

ON-SCREEN DISPLAY

This function will automatically turn the Projection TV on and off, one time only, every day, or once a week.

Use THUMB STICK ,  to highlight Event 1, 2 or 3 and then press THUMBSTICK to select. Use THUMB STICK  to change position of On time, Off time, Antenna, Channel, and On/Off Frequency. Use THUMB STICK  or  to select the time the TV will turn on and off. Use THUMB STICK  or  to select the day of the week you want the timer to turn on TV. Use number buttons to set the channel the TV will tune to when it automatically turns on. Use THUMB STICK  or  to select mode Once (TV will turn on/off one time only), Daily (TV will turn on/off at the same time every day), or Weekly-SUN (TV will turn on/off at same time every week). Press EXIT to quit the menu.

NOTE: 1. The Event Timer will be disabled if the clock setting is changed.

2. When the INFO button is pressed, the Event Timer Icon will only display the current date ON/OFF timer.

3. The Off Timer will only activate if the TV was turned on by the On Timer and no channel selection was made after this time. If you change the channel after the On Timer has been activated, the Off Timer will deactivate.

4. If no remote control button is pressed after Event Timer is activated, the TV will automatically turn of f after three hours. Therefore, do not Set Event Timer for more than three hours if you do not plan to control your television with the remote control.

CAUTION: Do not use your TV as a deterrent when away from home by using the On and Off Timers. For safety, the TV

should be turned off when you are away from home.

Set Event Timer

THUMB

STICK

SELECT

Setup

Move

SEL

Return

Set Event Timer

Event 1 --:-- AM --:-- AM Jan. 1, 2003 Ant A Ch -Event 2 --:-- AM --:-- AM Jan. 1, 2003 Ant A Ch -Event 3 --:-- AM --:-- AM Jan. 1, 2003 Ant A Ch --

Setup

Move

SEL

On/Off

Set Event Timer

Event 1

--:-- AM --:-- AM Jan. 1, 2003 Ant A Ch -Event 2 --:-- AM --:-- AM Jan. 1, 2003 Ant A Ch -Event 3 --:-- AM --:-- AM Jan. 1, 2003 Ant A Ch --

THUMB

STICK

Return

Set The Clock

Magic Focus Tune Up

Setup

Set The Inputs

Move

SEL

Select

Set The Color System Set Virtual HD Set Black Side Panel

Menu Preference

Set Event Timer

Set Closed Caption About Your TV

Please Set Clock First.

If the clock is not set, you can not use this function and the screen below will appear. The message on the screen will disappear after 3 seconds, then the screen automatically goes to the clock setup mode (see page 67).

Page 71

SETUP

ON-SCREEN DISPLAY

Caption Display: On/Off will turn the display on or off.

Auto will turn the display on when Mute/Soft Mute is on.

Caption Mode: Captions is for the program you are viewing.

Text is for additional information such as news reports or a TV program guide. This information covers the entire

screen and viewing the TV program is not possible. Text may not be available with every program.

CHANNEL: 1 is used for the primary language (usually English).

2 is sometimes used for a second language (may vary by region). 3 is sometimes used for a third language (may vary by region). 4 is sometimes used for a fourth language (may vary by region).

Use THUMB STICK ,  to highlight the function to change then press THUMB STICK to change the function. Press EXIT to quit menu or THUMB STICK  to return to previous menu.

Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video which are displayed on the TV screen. Your local TV program guide denotes these programs as

Set Closed

Caption

THUMB

STICK

SELECT

Setup

Move

SEL

Return

Set Closed Caption

Caption Display Off On Auto

Analog Captions

Mode: Captions Text

Channel: 1 2 3 4

Set The Clock

Magic Focus

Setup

Set The Inputs

Move

SEL

Select

Set The Color System Set Virtual HD Set Black Side Panel

Menu Preference

Set Event Timer

Set Closed Caption

About Your TV

NOTE: 1. CAPTION DISPLAY will not work when viewing a 480p, 720p, or 1080i input via the COMPONENT: Y-PBPRinputs.

2. When PIP Surf is on, Closed Caption will not work.

The TV model name and set dimensions will be displayed on the TV screen. The set dimensions of each TV model are listed on page 75.

About Your TV

Setup

Magic Focus Menu Preference

Set The Clock

Set The Inputs

Set The Color System Set Virtual HD Set Black Side Panel Set Event Timer Set Closed Caption

About Your TV

Move

Setup

About Your TV

Caution: Continuous on-screen

displays such as Video games, stock market quotations, and other fixed (non-moving) patterns can cause permanent damage. Such “SCREEN BURNS” are not covered by your Hitachi Factory Warranty.

Move

Setup

About Your TV

THUMB

STICK

SELECT

SEL

Select

THUMB

STICK

SELECT

SEL

Return

THUMB

STICK

Model: Dimensions (Inches) (mm)

Height: - / -

Width: - / Depth: - / -

SEL

Return

Move

Caution

Page 72

CARE OF YOUR HITACHI TELEVISION

AND YOUR REMOTE CONTROL

Dust the screen and cabinet with a soft cloth.

Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. Amild soap may be used if the screen is extremely dirty.

Place your Television away from extreme heat, humidity, and extremely dusty places.

Remove the plug from the wall outlet if your Television will not be used for a long period of time, for instances, when you go on vacation.

DO NOT

Do not clean your screen or cabinet with strong cleaners, polishes or a chemically treated cloth.

Do not place rubber or vinyl products or cellophane tape on your Television.

Do not touch the screen too often.

Do not subject the remote control to shocks such as dropping it on the floor, etc. Physical damage to the precision parts may result.

Avoid placing the remote control or the Simple Remote Control in a high humidity place or getting it wet. Do not leave it on or near a heater. Excessive heat or moisture may cause the unit to cease operation.

When the batteries run down, remote control operation will become erratic or possibly stop altogether. Replace the old batteries with two new “AA” or “AAA” size batteries. Do not use an old battery with a new battery.

Exposure of the viewing screen to prolonged direct sunlight or heat may cause the screen to permanently warp, resulting in a distorted picture.

Page 73

RECEPTION PROBLEMS

• IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances.

• GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception. Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers.

• SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture.

• RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture.

NOTE: The TV set can generate sound distortion in external devices such as a radio. Please separate radio equipment from

the TV set to a considerable distance.

Page 74

USEFUL INFO

HITACHI Projection Television incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage power surges.

IF YOUR TELEVISION SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE:

1. Press the power switch (ON/OFF switch) once.

2. If there is still no power, wait 30 seconds and press the power switch again.

3. If there is still no power, unplug the power cord from the wall. Wait 30 seconds and plug the power cord back in. Press the power switch again.

This protective technology should provide for years of lasting entertainment from your HITACHI Projection Television.

SYMPTOMS

CHECK THESE ITEMS AND

TRY THESE ADJUSTMENTS

No Picture, no sound

Sound OK, picture poor

Picture OK, sound poor

Picture blurred

Lines or streaks in picture

Poor reception on some channels

Picture rolls vertically

No color

Poor color



































Be sure external connection is correct

Be sure power cord is plugged in

Be sure TV is switched''ON"

Try another channel (station trouble)

Check antenna connections (back of TV)

Check antenna for broken lead-in wire

Check for local interference

Check outside antenna

Adjust Contrast control

Adjust Brightness control

Adjust Color control

Adjust Tint control

Adjust Volume control

Page 75

USEFUL INFO

•Velocity Modulation

• Six Aspect Modes

• Closed Caption Decoder

• 2-Tuner Picture in Picture

• Magic Focus (Auto Digital Convergence and Manual Adjustment)

• Dual Antenna Inputs

•Video Input Sensor

•3 Dimensional Y/C Comb Filter

• Full 1080i HDTV capable when used with a Set-Top Box.

• High bandwidth Digital Content Protection V1.0 compatible.

• Photo MC(View digital still pictures from a memory card).

•Technology.

•Technology. *SRS and the symbol are registered trademarks of SRS Labs, Inc. SRS technology is incorporated under license from SRS

Labs, Inc. *Licensed by BBE Sound, Inc. under USP4638258 and 4482866. BBE and BBE symbol are registered trademarks of BBE Sound, Inc. Manufactured under license from BBE Sound, Inc.

Features:

• Superfine Picture Quality

1280 Line Horizontal Resolution

• Remote (Controls many VCR brands, cable boxes, satellite boxes, and other audio equipment.)

• Extra Simple Remote for easy basic operations.

• New Easy-to-Use (3-Language) On-Screen Menu

• New AV Network Infra-Red (IR) System Control up to 4 components with one remote. (2 IR Mouse cables included.)

• Full Set of Input Jacks, including S-VIDEO

• COMPONENT VIDEO: Y-P

B/PR

Inputs:

•

Power Input . . . . . . . . . . . . .AC 120V, 60Hz

•

Stand-by Power . . . . . . . . . . . . . . . . . .1.3W

• Power Consumption

- Refer to rear panel at the back of the T.V.

• Antenna input impedance . . . . . . . . .75 Ohm

• Channel coverage . . . . . . . . . . . . . . .181ch.

VHF-Band . . . . . . . . . . . . . . . . . . . . .2 ~ 13

UHF-Band . . . . . . . . . . . . . . . . . . . .14 ~ 69

CATV Mid Band . . . . . . . . . . . . . . .A-5 ~ A-1

. . . . . . . . . . . . . . . . . . . . . . . . . . .A-I

Super Band . . . . . . . . . . . . . . . . . . . . .J-W

Hyper Band . . . . . . . . . . . . . . .W+1 - W+28

Ultra Band . . . . . . . . . . . . . . .W+29 - W+84

•Video . . . . . . . . . . . . . . . .1.0Vp-p, 75 Ohm

• S-Video

Luminance (Y) . . . . . . . . . .1.0Vp-p, 75 Ohm

Chrominance (C) . . . . . .0.286Vp-p, 75 Ohm

• Component Video

Luminance (Y) . . . . . . . . . . . . . . .1.0Vp-p, 75 Ohm

Chrominance (PB/PR) . . . . . . . . .0.7Vp-p, 75 Ohm

• Audio input Impedance . . . . . . . . . .47k Ohm

•Average input level . . . . . . . . . . . . . . . .470mVrms

• DVI - HDTV . . . . . . . . . . . . . . . . . . . . . .DVI 25pin

Outputs:

•Video . . . . . . . . . . . . . . . . . . . . .1.0Vp-p. 75 Ohm

• Audio (Fixed) . . . . . . . . . . . . .470mVrms, 1k Ohm

Dimensions:

57T500 57X500 65T500

65X500

• Height (in.) 54 3/16 54 3/16 59 7/8 (mm) 1,376.2 1,376.2 1,520.7

•Width (in.) 54 54 61

(mm) 1,372.0 1,372.0 1,549.0

• Depth (in.) 25 1/2 25 9/16 28 3/16

(mm) 647.9 648.7 716.0

•Weight (lbs.) 265 265 324

NOTE: Due to improvements, specifications in this oper-

ating guide are subject to change without notice.

Page 76

USEFUL INFO

Hitachi America, LTD.

Home Electronics Division

900 Hitachi Way

Chula Vista, CA 91914-3556

Hitachi America, LTD. Home Electronics Division

Hitachi has made every effort to assure you hours of trouble free operation from your unit. However, should you require service, a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico. Each facility will provide you with convenient and expedient assistance. Our service hotline operator will direct you to the Hitachi Authorized Service Facility nearest you. Just present proof of purchase and/or delivery receipts to the Hitachi Authorized Service Facility, and service will be rendered in accordance with the terms of the limited warranty as stated on your warranty card or operating guide.

Should you have any questions regarding warranty, service, operation, or technical assistance, please contact:

To locate an authorized HITACHI service facility in the continental U.S.A. and Canada,

DIAL TOLL FREE

7 days a week, 24 hours a day

800 HITACHI

(1-800-448-2244)

Page 77

USEFUL INFO

In Canada:

1-800-HITACHI

(1-800-448-2244)

Monday - Friday EST 9:00am - 7:00pm

Saturday EST 9:00am - 5:00pm

Hitachi Canada, LTD. Digital Media Division

Should you have any questions regarding warranty, service, operation, or technical assistance, please contact:

Look for your French Manual on the outside of the box. If the manual is missing, call

for a copy.

1-800-HITACHI

(1-800-448-2244)

Au Canada:

1-800-HITACHI

(1-800-448-2244)

Lundi - Vendredi L’EST 9:00am - 7:00pm

Samedi L’EST 9:00am - 5:00pm

Pour de plus amples renseignements sur le service durant la période couverte par la garantie, sur le fonctionnement ou pour de l’assistance technique communiquez avec:

La version français de votre manual se trouve a l’exterieur de la boîte. Si le manuel est manquant, coposez le

pour obenir votre copie.

1-800-HITACHI

(1-800-448-2244)

HITACHI CANADA, LTD.

6740 Campobello Road

Mississauga, ON L5N 2L8

Page 78

INDEX

Accessories, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Antennas (Connecting), . . . . . . . . . . . . . . . . . . . . .5, 6

Aspect Ratio, . . . . . . . . . . . . . . . . . . . . . . . . . . .31, 53

Audio (Sound Enhancement)

SRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . .51-52

Audio Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Auto Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Auto Noise Cancel . . . . . . . . . . . . . . . . . . . . . . . . . .51

AV Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-22

Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Bass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Black Enhancement . . . . . . . . . . . . . . . . . . . . . . . . .48

Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Channel Manager . . . . . . . . . . . . . . . . . . . . . . . .54-57

Channel Source . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Auto Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . .55

Clock

Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Closed Captions

Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Color System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Color Temperature . . . . . . . . . . . . . . . . . . . . . . . . . .48

Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Convergence (see Magic Focus)

DVI-HDTV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10, 18

Edge Enhancement . . . . . . . . . . . . . . . . . . . . . . . . . .48

Event Timer ANT A/B . . . . . . . . . . . . . . . . . . . . . . . .70

Input Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

IR Blaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10, 20

Language

Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Locks

Change Access Code . . . . . . . . . . . . . . . . . . . . . . 58

Channel Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Input Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Locks (Continued)

Front Panel Lock . . . . . . . . . . . . . . . . . . . . . . . . . . .58

TV Time Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Movie Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

TV Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

TV Ratings (Canadian - English) . . . . . . . . . . . . . . .61

TV Ratings (Canadian - French) . . . . . . . . . . . . . . .62

Loudness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Magic Focus

Auto Convergence . . . . . . . . . . . . . . . . . . . . . . .7, 64

Manual Convergence . . . . . . . . . . . . . . . . . . . . . . .65

Menu Preference

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Monitor Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Noise Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Perfect Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Photo MC . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7,27-28

Picture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Picture-in-Picture (PIP) . . . . . . . . . . . . . . . . . . . . .34-36

Picture-outside-Picture (POP) . . . . . . . . . . . . . . . . . .34

Remote Control

Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-44

Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . .4

Programming Codes . . . . . . . . . . . . . . . . . .37-42, 44

Simple Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Sound Enhancement . . . . . . . . . . . . . . . . . . . . . .51-52

Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Connecting External Speakers . . . . . . . . . . . . . .5, 14

Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Tint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Treble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Video Settings . . . . . . . . . . . . . . . . . . . . . . . . . . .47-50

Virtual HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Page 79

NOTES

Page 80

QR57061

Hitachi 57T500A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual