Hitachi 37HLX99 User Manual

Operating Guide for 37HLX99
IMPORTANT SAFETY INSTRUCTIONS....................................................................................... 2-3
FIRST TIME USE ....................................................................................................................... 4-22
THE REMOTE CONTROL........................................................................................................ 23-40
ON-SCREEN DISPLAY ............................................................................................................ 41-69
USEFUL INFORMATION.......................................................................................................... 70-78
END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE...........................................79-87
APPENDIXES...........................................................................................................................88-89
INDEX.............................................................................................................................................90
As an Energy Star®Partner, Hitachi, Ltd. has determined that this product meets the Energy Star energy efficiency.
®
guidelines for
Important Safety Instructions
SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI LCD TELEVISION
Our reputation has been built on the quality, performance, and ease of service of HITACHI LCD televisions.
Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI LCD television.
Please fill out your warranty card and mail it to HITACHI. This will enable HITACHI to notify you promptly in the improbable event that a safety problem should be discovered in your product model.
Follow all warnings and instructions marked on this LCD television.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to a person.
The exclamation point within an equilateral
triangle, is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
READ BEFORE OPERATING EQUIPMENT
Follow all warnings and instructions marked on this
LCD television.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding
2
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use the attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15.Televisions are designed to comply with the
recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to overturn resulting in product damage and/or personal injury.
16. Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
17. An outdoor antenna should not be located in the vicinity of overhead power lines or other electrical circuits.
18. If an outside antenna is connected to the receiver be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding for the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna­discharge unit, connection to grounding electrodes and requirements for the grounding electrode.
NEC National Electric Code
Note to the CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-44 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
Important Safety Instructions
Public viewing of copyrighted material
Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require prior authorization from the broadcaster or owner of the video program material.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited consumer uses only unless otherwise
Power source
This LCD television is designed to operate on 120 volts 60 Hz, AC current. Insert the power cord into a 120 volt 60 Hz outlet. The power cord is used as the
disconnect device and shall remain readily operable.
To prevent electric shock, do not use the LCD television’s (polarized) plug with an extension cord, receptacle, or other outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.
Never connect the LCD television to 50 Hz, direct current, or anything other than the specified voltage.
Caution
Never remove the back cover of the LCD television as this can expose you to very high voltages and other hazards. If
the television does not operate properly, unplug the LCD television and call your authorized dealer or service center.
Caution
Adjust only those controls that are covered in the instructions, as improper changes or modifications not expressly approved by HITACHI could void the user’s
warranty.
Warning
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
The LCD television should not be exposed to
dripping or splashing and objects filled with liquids, such as vases, should not be placed on the television.
This apparatus shall be connected to a mains
socket outlet with a protective earthing connection.
authorized by Macrovision. Reverse engineering or disassembly is prohibited.
Note
This digital television is capable of receiving analog basic, digital basic and digital premium cable television programming by direct connection to a cable system providing such programming. A CableCARD provided by your cable operator is required to view encrypted digital programming. Certain advanced and interactive digital cable services such as video-on-demand, a cable operator’s enhanced program guide and data-enhanced television services may require the use of a set-top box. For more information call your local cable company.
Note
There are no user serviceable parts inside the
LCD television.
Model and serial numbers are indicated on back side
and right side of the LCD television (page 78).
Lead/Mercury Notice
Hg
This pr
oduct contains lead and a lamp that contains
mer
cury. Dispose of this product and its lamp in accordance with applicable envir lamp recycling and disposal information, go to www.lamprecycle.or disposal information contact your local government agency or Electronic Industries Alliance at US) or the Electr
www.epsc.ca FOR MORE INFORMA
g. For pr
www
.eRecycle.org
onic Product Stewardship Canada at
(in Canada).
TION, CALL 1-800-HIT
onmental laws. For
oduct recycling and
(in California), the
www.eiae.org(in the
ACHI.
3
Accessories
Check to make sure you have the following accessories before disposing of the packing material.
Remote Control
Two “AA” size,
1.5V batteries
Power Cord
Table Top Stand
Power Swivel Cable
First time use
+
-
/
2 IR Blaster Cables
1 Ferrite Core (see page 14)
Note: Please visit our
For U.S. models:
For optional accessories, please access our web site at:
website for optional
accessories.
www.hitachi.us/tv
CAUTION: 1. Ceiling mounting is not recommended. Mounting the panel on the ceiling does not
provide adequate ventilation for the electronics or proper support for the front glass panel. This LCD television product is designed for a maximum tilting angle of 45 degrees from vertical.
2. This stand for use only with Hitachi 37HLX99. Use with other apparatus is capable of resulting in instability causing possible injury.
Remote Control Unit CLU-3861WL Two IR Blaster cables (P# EY01641).
(Part No. HL02069). 쐂 Power Swivel Cable (P# EW08432).
Two “AA” size, 1.5V batteries (P# FQ00021). 1 Ferrite Core (P#2169513).
Power Cord (P# EV01841). Table Top Stand (P# QJ02673 ).
REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT
BOTTOM VIEW
(Remote Control)
1. Open the battery cover of the remote control by pushing down and sliding the back cover off.
2. Insert two new “AA” size batteries for the
remote control. When replacing old batteries, push them
towards the springs and lift them out.
Press down and slide back to remove.
3. Match the batteries to the (+) and (-) marks in the battery compartment.
4. Replace the cover.
CAUTION: Do not insert batteries with the ‘+’and ‘-’ polarities reversed as this may cause the batteries to swell or rupture resulting in leakage.
4
How To Set Up Your New Hitachi LCD Television
To take measures to prevent the LCD Television from tipping over and prevent possible injury it is important to mount the unit in a stable and flat surface.
Securing to a table-top
1. Using wood screws (two) fasten the set to the
clamping screw holes on the rear of the LCD
TV stand as shown below.
2. Using commercially available wood screws, secure the set firmly in position.
Wire
Wood screw two places
Securing to a Wall
1.Keep the LCD television 4 inches away from the wall except when mounted using the wall mount bracket.
2. Secure the television to the wall as shown.
A
(a) Power Swivel
NOT USED
B
(b) Power Swivel
USED
37"
AB
4 in. 12 in.
10 cm 30 cm
* Please adjust the wire length to avoid touching the wall when turning the TV.
ANTENNA
Unless your LCD Television is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient.
LOCATION
Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set. In order to prevent an internal temperature increase, maintain a space of 10 cm (4 inches) from the sides/back of the Television, and 30 cm (12 inches) from the top of the television to the wall. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.
10 cm (4 inches)
30 cm (12 inches)
10 cm (4 inches)
First time use
NOTES: 1. Do not block the ventilation holes of the
LCD Television. Blocking the ventilation holes might cause fire or defect.
2. In case of an abnormal symptom, unplug the AC cord.
3. If you purchased the wall mount bracket
option, please ask for professional installer. Do not install by yourself.
4. Install the unit at a proper area where it does
not expose anyone to any danger of hitting
themselves (for example their hands, head
or face, etc.) against the edge of the unit and cause personal injury.
5. If the Power Swivel feature will not be
used, the LCD television should be secured to the wall as shown in fig. (a).
6. If the Power Swivel feature will be used,
the LCD television should be secured to the wall as shown in fig. (b).
Caution when moving the main unit
As this product is heavy, whenever it is moved, two people are required to transport it safely. Whenever the unit is moved it should be lifted forward using the top and base on both sides of the Television for stability. When moving the Television, lift the handles and the
botttom frame as shown below.
CONNECT POWER SWIVEL CABLE
Connect one end of cable (Arrow mark facing left) to the swivel slot of the LCD Rear Panel. Connect the other end (Arrow mark facing front)to the swivel slot of the Table Top Stand.
TURNING RADIUS
The maximum turning radius is 30˚ (left and right). Do not place any objects on the path of the monitor when using the power swivel feature.
C
CD
10.59 in. 1 3.93 in.
37"
D
27 cm 3 6 cm
37
5
First time use
How to set up your new HITACHI LCD Television
SETTING FOR WALL MOUNTING
STEP (1) :
Please locate the STAND PLATE metal on the back of the TV . This metal is use to hold the TV and the Base ; so it needs to be remove in order to separate the TV from the Base.
STAND PLATE METAL
STEP (2):
Please remove the 3 screws and the STAND PLATE metal from the TV, then put back only the screw to the back cover. Now the 4 screws that holds the TV STAND can be remove to separate the TV from the STAND BASE.
4 SCREWS
PLACE BACK THIS SCREW
3 SCREWS
STAND PLATE METAL
TV STAND BASE
NOTE: Use the specified WALL MOUNT base for the LCD TV depending on the size of your TV.
Please access our web site at: www.hitachi.us/tv for recommended accessories for your tv.
6
How to set up your new HITACHI LCD Television
VIEWING
The reccomended viewing horizontal and vertical angles for this LCD TV is 160°.
During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the TV can be located in a different section of the room.
20
First time use
BEST
VERTICAL VIEWING
ANGLE
If the TV’s audio output will be connected to a Hi-Fi system’s external speakers, the best audio performance will be obtained by placing the
0’
3’
5’
10’ 15’ 20’
speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For best stereo separation, place the external speakers at least four feet from the side of the TV, place the surround
R
S
speakers to the side or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker placement for best performance.
ANTENNA CONNECTIONS TO REAR JACK PANEL
4" Minimum
4" Minimum
L
80
BEST HORIZONTAL
5'
10'
VIEWING ANGLE
80
15' 20'
S
VHF (75-Ohm) antenna/CATV (Cable TV)
When using a 75-Ohm coaxial cable system, connect CATV coaxial cable to the AIR/CABLE (75-Ohm) terminal. Or if you have an antenna, connect the coaxial cable to the same AIR/CABLE terminal.
AIR / CABLE
To CATV cable
VHF (300-Ohm) antenna/UHF antenna
When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna leads to screws of the VHF or UHFadapter. Plug the adapter
To outdoor antenna
or
into the antenna terminal on the TV.
AIR / CABLE
When both VHF and UHF antennas are connected
Attach an optional antenna cable mixer to the TV antenna terminal, and connect the cables to the antenna mixer. Consult your dealer or service store
for the antenna mixer.
To UHF antenna
AIR / CABLE
Antenna Mixer
To outdoor VHF or UHF antenna
To outdoor antenna or CATV system
NOTE: Connecting a 300-Ohm twin lead connector may cause interference. Using a 75-Ohm coaxial
cable is recommended.
7
Hook-up Cables and Connectors
Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output and input connector types required by the various components and the length of each cable.
First time use
300-Ohm Twin Lead
Cable
This outdoor antenna cable must be connected to an antenna adapter (300-Ohm to 75-Ohm).
A/V
Cable
Used on all standard video and audio cables which connect to inputs and outputs located on the
television’s rear jack panel and side control panel.
“F” Type 75-Ohm Coaxial Antenna
For connecting RF signals (antenna or cable TV) to the antenna jack on the television.
S-Video (Super Video)
Cable
This connector is used on camcorders, VCRs and laser­disc players with an S-Video feature in place of the standard video cable to produce a high quality picture.
Optical Cable
This cable is used to connect to an audio amplifier with an Optical Audio In jack. Use this cable for the best sound quality.
HDMI Cable
This cable is used to connect your external devices such as Set-Top-Boxes or DVD players equipped with an HDMI output connection to the TV’s HDMI input.
Stereo Cable (3.8mm plug to 3.5mm plug)
Used on all standard video and audio cable which connect to inputs and outputs located on the rear jack
panel and side control panel.
USB Cable
This cable is used to connect your digital camera to the
Photo Input in the side of the LCD television.
IR Blaster Cable (Provided)
Connect the IR Blaster to the IR output of your LCD Television when using other devices. You must place the IR blaster in front of the corresponding IR window of your cable box or VCR. This connection allows your TV to control your cable box or VCR.
Power Swivel Cable (Provided)
This cable is used to connect the swivel stand to the
rear panel of the LCD Television.
AUDIO OUT
3.8mm STEREO MINI-PLUG
2 RCA TYPE PLUGS
8
Quick Reference Remote Control Buttons and Functions
In addition to controlling all of the functions on your HITACHI LCD TV, the new remote control is designed to
operate different types of devices, such as, DVD Players, CBL (Cable Boxes), set-top-boxes, satellite receivers,
and VCRs. The remote control must be programmed to control the chosen device. Please see pages 23-40 for a
complete description of all features and programming of the Remote Control.
(TV, DVD, CBL, STB, PVR/VCR, AMP/CD)
Turns the selected device on and off.
POWER BUTTON
First time use
Turns on or blinks to show remote control
mode when the SOURCE ACCESS buttons
(TV, DVD, CBL, STB, PVR/VCR, AMP/CD)
Changes the mode of the Universal Remote
The Cursor Pad is used as a cursor to navigate
through the OSD and INPUT menu systems.
The Select button is used to Select/Activate
CURSOR UP & DOWN /CH + & CH - BUTTON
The CH+ or CH- is used to change channels up or down.
The Cursor UP or DOWN to navigate through the OSD and INPUT menu systems.
Displays various information on the screen,
Scroll up and down to adjust the audio level of your
(TV, DVD, CBL, STB, PVR/VCR, AMP/CD)
Used to manually enter the TV channel, and used
for numeric entry when navigating through the OSD,
SOURCE ACCESS BUTTONS
Control to control the device selected.
Changes the aspect ratio of the TV.
Toggles picture mode settings between
(TV, DVD, CBL, STB, PVR/VCR)
Accesses the OSD menu system.
CURSOR PAD/SELECT BUTTON
(TV, DVD, CBL, STB, PVR/VCR)
TV. Push down on the wheel to mute.
MODE INDICATOR
are pressed.
ASPECT BUTTON
DAY and NIGHT mode.
MENU BUTTON
highlighted menu items.
(TV, CBL, STB, VCR)
INFO BUTTON
(TV, STB, CBL, PVR)
such as channel information.
VOLUME WHEEL
NUMERIC BUTTONS
(TV)
DAY/NIGHT
(TV)
(TV, AMP/CD)
INPUTS .
DVD/VCR CONTROL BUTTONS (DVD, PVR/VCR, AMP/CD)
Controls the functions of your VCR, DVD and audio devices.
PAUSE BUTTON (TV,PVR/VCR, DVD, AMP/CD)
Press to show and change the Freeze mode of the TV. Also used to pause other devices when the remote is in DVD, PVR/VCR, or AMP/CD mode.
PIP CONTROL BUTTONS
(TV)
Press to show and change the Picture-in-Picture mode.
GUIDE BUTTON (TV, STB, CBL, PVR)
Accesses the TV Guide On Screen system (see page 49) of the TV or the program guide of other devices.
EXIT BUTTON (TV, CBL, STB, PVR/VCR)
Exits out of the OSD, INPUTS or AV NET menu systems if their menu is displayed.
LAST CHANNEL BUTTON
(TV, CBL, STB, PVR)
Switches between the current and last channel viewed.
INPUTS BUTTON (TV, AMP)
Accesses the INPUTS menu system.
CHANNEL WHEEL (TV, CBL, STB, PVR/VCR, AMP/CD)
Scroll up or down to change channel. Push down on the wheel to access (FAV) Favorite Channel mode. (Favorite channel is only available for TV mode.)
TM
(-) BUTTON
The (-) button is used when the remote is in
Set-Top-Box (STB) mode or when the TV uses
(TV,STB)
a digital input.
LIGHT BUTTON
Press to use the back light feature. Can also be used to change backlight mode.
LEGEND TV – Television PVR – Video Recorder/Player CBL – Cable Box DVD – Digital Video Disc Player
STB – Set-Top-Box AMPAudio Amplifier
NOTES: 1. The TV’s remote control sensor is located on the right lower portion of the TV screen. To
control TV functions, please point the remote control directly at the remote control sensor for best results.
2. VCR precode is included in the PVR mode.
3. CD precode is included in the AMP mode.
4. Pressing the Light button will illuminate the backlight for 8 seconds.
9
First time use
Front/Side Panel Controls
햹 햺
SIDE POWER button
Press this button to turn the LCD Television ON/OFF. It can also be turned ON/OFF by remote control. The “MAIN POWER” button must be at stand-by mode.
MENU/SELECT button
This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode.
SIDE HDMI INPUT (5)
Use the side HDMI input for extrenal devices such as Set-Top-Boxes or DVD players equipped with an HDMI output connection (see page 15 for reference).
INPUT/EXIT button
Press this button to access the INPUT menu. Press again to exit the MENU mode.
Firmly bind the cables.
Thread the square hole with the band.
Hook the band to the claw.
POWER button
Television MAIN POWER button
This power button is for the complete system, and must be turned ON/OFF manually. It is recommended to leave the “MAIN POWER” to ON condition (lights red) for stand-by mode.
The Main Power button is located on
the underside of the
bottom, under the label “MAIN POWER”.
CHANNEL selector
Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as the cursor down () and up () buttons when in MENU mode.
VOLUME level
Press these buttons to adjust the sound level. The volume level will be displayed on the TV screen. These buttons also serve as the cursor left () and right () buttons when in MENU mode.
10
NOTE: When the “MAIN POWER” button is set to
OFF or the TV is unplugged, the clock will stop and may eventually reset itself.
Front/Side Panel Controls
PHOTO INPUT
Insert USB cable from your Digital Camera, USB memory or memory card USB drive to view your
digital still pictures (see page 27).
POWER light indicator
To turn the TV ON, press the main power switch located on the lower right side of the TV. A red stand-by indicator lamp located on the lower right of the front bezel will illuminate. The LCD TV is now ready for remote ON/OFF operation.
Indicating Lamp Power Status Operating
Lamp 1 Lamp 2
Off
Lights
Red
Off
Off
Lights
Orange
REMOTE CONTROL sensor
Point your remote at this area when selecting channels, adjusting volume, etc.
IR OUT sensor
Point your equipment’s remote control at this area. The IR will pass through the IR Blaster cables
to your equipment.
Off
Off
Blinking
Blue
Lights
Blue
Off
OFF.
OFF.
(Stand-by) is ON.
OFF.
(Turning ON )
nO
Off
(Power Saving) except antenna
When the main power switch is set to O.
When the main power switch on the TV
TV MAIN POWER is ON ; but no picture is shown.
TV MAIN POWER is ON ; picture is shown.
TV MAIN POWER is ON with no signal input
(no sync. signal).
Lamp 2 Lamp 1
IR Sensor
First time use
SIDE INPUT JACKS (for INPUT:5)
INPUT 5 provide Y-PBPR jacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may use
composite video signal for this input.
NOTE: 1.
Your component outputs may be labeled
Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PB input and the components R-Y output to the TV’s P
2.
Your component outputs may be labeled Y-C C
B output to the TV’s PB input and the
component C
It may be necessary to adjust TINT to
3. obtain optimum picture quality when using the Y-P
4.
INPUT 3, INPUT 4 and INPUT 5 (Y/VIDEO) can
be used for composite video and component
video input.
NOTES: 1. Your HITACHI LCD TV will appear to be turned OFF (lights orange) if there is no video input
R input.
BCR. In this case, connect the component
R output to the TV’s PR input.
BPR inputs (see page 43).
when INPUT : 1, 2, 3, 4 and 5. Check the Power Light condition to make sure the TV is turned off or in Stand-by mode (lights red) when not in use.
2. Remote Control can not turn ON/OFF the “MAIN POWER” of the TV.
11
First time use
Rear Panel Connections
Antenna Input
To switch between Cable and Air input, go to the Channel Manager option to change the signal source CABLE or AIR (see page 52).
Audio/Video Inputs 1, 2, 3 and 4
By using the INPUTS button, the CURSOR PAD ( and ), and the SELECT button or CURSOR PAD of the remote control, you can select each video source. Use the audio and video inputs to connect external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (if you have mono sound, insert the audio cable into the left audio jack).
햹 햶
MONITOR OUT & HI-FI AUDIO OUT
These jacks provide fixed and variable audio and video signals (CABLE/AIR or INPUTS ) which are used for recording. Use the S-VIDEO Output for high quality video output. Component
signal to Input 3,4 and 5, and HDMI inputs will not
have monitor output.
Optical Out (Digital Audio)
This jack provides Digital Audio Output for your audio device that is Dolby
®
Digital and PCM
compatible, such as an audio amplifier.
NOTE: *Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
S-VIDEO Inputs 1 and 2
Inputs 1 and 2 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability.
NOTE: 1. You may use VIDEO or S-VIDEO inputs to
connect to INPUT 1 and 2, but only one of these inputs may be used at a time.
2. S-VIDEO output may be used for recording, only when the input is of S­VIDEO type.
HDMI 1, 2 & 5 (High Definition Multimedia
Interface)
ABOUT HDMI HDMI is the next-generation all digital interface for consumer electronics. HDMI enables the secure distribution of uncompressed high-definition video and multi­channel audio in a single cable. Because digital television (DTV) signals remain in digital format, HDMI assures that pristine high-definition images retain the highest video quality from the source all the way to your television screen.
Use the HDMI input for your external devices such as Set-Top-Boxes or DVD players equipped with an HDMI output connection.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
12
trademarks of HDMI Licensing LLC.
NOTE: 1. The HDMI input is not intended for use
with personal computers.
2. Only DTV formats such as 1080i, 720p, 480i and 480p are available for HDMI input.
Component: Y-P
INPUTS 3 and 4 provide Y-P
BPR Inputs
BPR jacks for
connecting equipment with this capability, such as a DVD player or Set Top Box. You may use composite video signal for both inputs.
NOTE: 1. Do not connect composite VIDEO and
S-VIDEO to INPUT 1 or 2 at the same
time. S-VIDEO has priority over VIDEO input.
2. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s P
B
input and the components R-Y output to the TV’s P
R input.
3. Your component outputs may be labeled Y-C
BCR. In this case, connect the component
C
B output to the TV’s PB input and the
component C
R output to the TV’s PR input.
4. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-P
BPR inputs (see page 43).
5. To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-P
BPR jacks and HDMI
Input.
6. INPUT 3,4and 5 (Y/VIDEO) can be used for composite video and component video input.
IR Out / G-Link
This jack provides IR output to your external components
(VCR, Cable box, DVD player, etc.). This connection
will allow you to control the external components with your LCD Television’s remote control .
(For reference see pages 16).
For FACTORY use only.
Rear Panel Connections
T
Upgrade Card
This card slot is for future software upgrades. Hitachi will notify you if a software upgrade is required for your TV. In order to receive written notification, please complete and return your warranty card.
Power Swivel Connector
Connects to the Power Swivel Table Top Stand.
CableCARD Slot
This slot is for the CableCARD that will be provided by your local cable operator to gain access to chosen cable channels. The CableCARD will allow you to tune digital and high definition cable channels. Please call your local cable operator if this service is available before requesting a CableCARD (also known as Point of Deployment (POD) module).
1. Connect a coaxial cable to cable terminal of the Rear Panel Jacks.
2. Insert the CableCARD into the slot (Top of card
should be facing towards you as shown below). Completely insert the card until the back end
aligns with the line as shown.
Digital Cable
If the CableCARD is properly installed or removed, the TV will display the following respective screens.
First time use
CableCARD is installed
OR
CableCARD is not installed
After the CableCARD is installed, wait until the second screen below appears.
INSERTINSER
NOTE: 1. A digital cable subscription is required.
2. Do not insert a PCMCIA card into the CableCARD slot.
Acquiring Data.
Please wait.
In order to start cable service
for this device, please contact
your cable provider
CableCARD(tm): 123-456-789-1 Host: 123-456-789-1 Data: 123-456-789-1
Unit Address: 123-456-789-1
Press EXIT to return
Please take note of all information on the screen (you will provide this information to your cable operator). Call your cable operator and give them the information
from the card to start your cable service (refer to page 67
for more information).
13
The LEFT SIDE panel jacks are provided as a convenience to allow you to easily connect a camcorder , DVD, Video Game, VCR and a Digital Camera as shown in the following examples:
NOTE: 1. Completely insert connection cord plugs when connecting to left side panel jacks. If you do not, the
played back picture may be abnormal.
Connecting External Video Sources
Video Camera
OUTPUT
R L
INPUT
PHOTO
lenaPediStfeL
INPUT 5
lenaPediStfeL
R
L/MONO
PR P
AUDIO
B
Y / VIDEO
PHOTO
INPUT
R
L/MONO
AUDIO
First time use
Note : Connection cables will depend
on the external device specification.
OUTPUT
P
PR/C
R L
Video Game
OUTPUT CAPABILITY
DVD , Set Top Box,
Video Game Console.
Y
B/CB
R
COMPONENT
PR P
B
Y / VIDEO
V
INPUT 5
R
L/MONO
PR P
AUDIO
B
Y / VIDEO
Ferrite Core Instructions:
1. Wrap once the USB cable on the ferrite core near the Photo Input as shown.
2. Fold and close the ferrite core while being careful not to pinch the cable.
lenaPediStfeL
PHOTO
INPUT
Ferrite Core
USB Cable
Digital Camera
14
Connecting External Video Sources
The RIGHT SIDE panel jacks are provided as a convenience to allow you to easily connect HDMI or DVI signals from a DVD, Set Top Box , Video Game as shown in the following examples (When connecting DVI signal it will
need to connect the audio output into the Left Side Input jacks) :
A) Connecting HDMI signal.
Right Side Panel
HDMI DIGITAL
OUTPUT CAPABILITY
DVD , Set Top Box,
Video Game Console.
Right Side Panel
Note : Connection cables will depend
on the external device specification.
B) Connecting DVI signal.
Left Side Panel
R
L/MONO
AUDIO
DVI to HDMI
Cable
DIGITAL OUTPUT
DVI DIGITAL
OUTPUT CAPABILITY
DVD , Set Top Box,
Video Game Console.
OUTPUT
R L
INPUT 5
PR P
B
Y / VIDEO
Back of
HDTV Set-Top-Box or DVD Player
First time use
NOTE: 1. Completely insert connection cord plugs when connecting to side panel jacks. If you do not, the
played back picture may be abnormal.
The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set
Top Box to your LCD TV is dependent on the model and features of each component. Check the
owner’s manual of each component for the location of video and audio inputs and outputs.
The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your particular assortment of components and features. For best performance, video and audio cables should be made from coaxial shielded wire.
Before Operating External Video Source
Connect an external source to one of the INPUT terminals, then press the INPUTS button to show the
INPUTS menu. Use the CURSOR PAD ( and ) to select the Input of your choice. Then press the SELECT button or the CURSOR PAD to confirm your choice (see page 26).
Input 5 Photo Input
Cable
Air /
Input 1
Input 2
Move SEL Sel.
15
Rear Panel Connections
Antenna
Outside
or
Cable TV coaxial cable
2-Way signal splitter
First time use
ANT IN
Optional
S-VIDEO
VCR #1
OUTPUT
VLR
DIGITAL
OUTPUT CAPABILITY
DIGITAL OUTPUT
AUDIO OUT
DVI
to
HDMI
16
Optional
OUTPUT
YP
B/CBPR/CR
DVD Player
L R
S-VIDEO
VCR #2
V L R
INPUT
(PROVIDED)
CONNECT TO G-LINK/IR OUT
NOTE: Cables are optional, except when specified.
V L R
S-VIDEO
OUTPUT
Laserdisc player,VCR, camcorder, etc.
CONNECT TO IR OUT
P
Y P
B
R
OUTPUT
HDTV Set-Top Box
(PROVIDED)
L R
HDMI
to
HDMI
HDMI OUTPUT
HDMI DIGITAL
OUTPUT CAPABILITY
Tips on Rear Panel Connections
• S-VIDEO, Y-PBPR, or HDMI connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature.
• If your device has only one audio output (mono sound), connect it to the left audio jack on (L/(MONO)) the Rear Panel.
• Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.
• A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line
output (INPUT: 1 in the example on page 16). Refer to your VCR operating guide for more information on
line input-output connections.
• Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack.
• COMPONENT: Y-PBP DVD players and set-top-boxes. Use these connections in place of the standard video connection if your device has this feature.
• Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PBinput and the components R-Y output to the TV’s PRinput.
• Your component outputs may be labeled Y-CBCR. In this case, connect the components CBoutput to the TV’s PBinput and the components CRoutput to the TV’s PRinput.
• It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPRinputs. (See
page 43)
• To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPR, and HDMI input jacks.
Input 1 , 2 or 5 can accept HDMI signal.
• S-VIDEO monitor output may be used for recording only when the input is of S-VIDEO type.
(Input 3, 4 & 5) connections are provided for high performance components, such as
R
First time use
• When using a HDMI input from a Set-Top-Box, it is recommended to use a 1080i or 720p input signal.
INSTALLATION RECOMMENDATION:
1. Video signals fed through a VCR may be affected by copyright protection systems and the picture will be distorted on the television.
2. Connecting the television directly to the Audio /Video output of a Set-Top-Box will assure a more normal picture.
17
First time use
Connecting External Video Sources
CONNECTING A VIDEO AND STEREO AUDIO SOURCE TO INPUT1 – INPUT5
1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the Rear Panel to the right.
2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.
3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.
4. Press the INPUTS button, then select INPUT 2 from the INPUTS menu to view the program from the VCR or laserdisc player.
5. Select CABLE or AIR from the INPUTS menu to return to the last channel tuned.
Back of
VCR
OUTPUT
VCR
NOTE: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and
sound that is played back will be abnormal if the connection is loose.
2. A single VCR can be used for VCR #1 and VCR #2 (see page 16) but note that a VCR cannot record its own video or line output. Refer to your VCR operating guide for more information on line input­output connections.
3. When INPUT 3 , 4 or 5 are used, it is necessary to connect the video output of the device to the Y/VIDEO input jack of the TV (For INPUT 5 please see page 14 for reference).
CONNECTING AN S-VIDEO AND STEREO AUDIO SOURCE TO INPUT 1, 2
CABLE
or
Air signal
1. Connect the cable from the S-VIDEO OUT of the S-VHS VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the Rear Panel to the right.
2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.
3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.
4. Press the INPUTS button, then select INPUT 1 from the INPUTS menu to view the program from the VCR or laserdisc player.
5. Select CABLE or AIR from the INPUTS menu to return to the last channel tuned.
Back of VCR or
Laserdisc Player
R L V
OUTPUT
VCR or Laserdisc Player
NOTE: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and
sound that is played back will be abnormal if the connection is loose.
2. A single VCR can be used for VCR #1 and VCR #2 (see page 16), but note that a VCR cannot record its own video or line output. Refer to your VCR operating guide for more information on line input­output connections.
18
S-VIDEO
Connecting External Video Sources
CONNECTING A COMPONENT SOURCE WITH HDMI OR DVI CAPABILITY TO INPUT 1, 2 OR 5
1. Connect the HDMI or DVI to HDMI connection cable from the output of the HDTV set top box or DVD player to the HDMI input as shown on the Rear panel below.
2. With DVI output, connect the cable from the AUDIO OUT R of the HDTV set top box or DVD player to the INPUT (AUDIO/R) jack as shown on the Rear Panel below.
3. With DVI output, connect the cable from the AUDIO OUT L of the HDTV set top box or DVD player to the INPUT (AUDIO/L) jack as shown on the Rear Panel below.
4. Press the INPUTS button, then select INPUTS 1, 2 or 5 to view the program from the HDTV set top box or DVD player.
5. Select CABLE or AIR from the INPUTS menu to return to the last channel viewed.
HDMI input
CABLE
or
Air signal
NOTE: 1. Completely insert the connection cord
plugs when connecting to rear panel jacks. The picture and sound that is played back will be abnormal if the connection is loose.
2. The HDMI input on INPUT 1 , 2 and 5 contains the copy protection system called High-bandwidth Digital Content Protection (HDCP). HDCP is a cryptographic system that encrypts video signals when using HDMI connections to prevent illegal copying of video contents.
3. HDMI is not a “NETWORK” technology. It establishes a one-way point-to-point connection for delivery of uncompressed video to a display.
4. The connected digital output device controls the HDMI interface so proper set­up of device user settings determines final video appearance.
5. When using a DVI to HDMI cable, connect the Audio Out L and R cables at the same INPUT (1 , 2 or 5) as your HDMI INPUT(1 , 2 or 5). (For INPUT 5 please see page 15 for reference).
First time use
DVI to HDMI Input
CABLE
or
Air signal
HDMI
P
R
LR
OUTPUT
DIGITAL OUTPUT
P
B
DIGITAL OUTPUT
Cable
Back of
HDTV Set-Top-Box or DVD Player
DVI to HDMI
Cable
Back of HDTV Set-Top-Box or DVD Player
or
HDTV Set-Top-Box or DVD Player
or
or
HDTV Set-Top-Box or
DVD Player
19
Connecting External Audio/Video Devices
CONNECTING A COMPONENT AND STEREO AUDIO SOURCE TO INPUT 3 , 4 or 5 : Y- PBPR.
First time use
1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the Rear panel below.
2. Connect the cable from the PB/CBOUT or B­Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB)jack.
3. Connect the cable from the PR/CROUT or R­Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PR) jack.
4. Connect the cable from the AUDIO OUT R of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/R) jack.
5. Connect the cable from the AUDIO OUT L of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/L) jack.
6. Press the INPUTS button, then select INPUT 4 from the INPUTS menu to view the program from the Laserdisc/DVD player or HDTV set top box.
7. Select CABLE or AIR to return to the last channel tuned.
NOTE: 1. Completely insert the connection cord
plugs when connecting to rear panel jacks. The picture and sound that is played back will be abnormal if the connection is loose.
2. See page 17 for tips on REAR PANEL
CONNECTIONS.
(For INPUT 5 please see page 14 for reference).
CABLE
or
Air signal
OUTPUT
L R Y P
HDTV Set-Top Box
B PR
AUDIO
L R
Back of DVD Player
OUTPUT
OR
VIDEO
PR/CR PB/CB Y
DVD Player
20
Connecting External Audio/Video Devices
CONNECTING A VIDEO AND MONAURAL AUDIO
SOURCE TO INPUT 1 ~ INPUT 5
CABLE
or
Air signal
1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the Rear Panel on
the right.
2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.
3. Press the INPUTS button, then select INPUT 2 from the INPUTS menu to view the program from the VCR or the laserdisc player.
4. Select CABLE or AIR from the INPUTS menu to return to the previous channel.
(For INPUT 5 please see page 14 for reference).
CONNECTING OPTICAL OUT TO AN EXTERNAL AUDIO AMPLIFIER
CABLE
To monitor the audio level of the LCD TV to an
or
Air signal
external audio amplifier, connect the system as shown on the right. The “OPTICALOUT” from the Rear Panel is a fixed output. The Volume of the amplifier is controlled by the amplifier, not by the
LCD Television. The OPTICAL OUT terminal
outputs all audio sources with Optical IN capability.
Back of
VCR
AUDIO OUT VIDEO OUT
OUTPUT
VCR
First time use
1. Connect an optical cable from the Optical out to
the Optical input of a separate Stereo System
Amplifier as shown on the Rear Panel on the
right.
CONNECTING MONITOR OUT
CABLE
or
The MONITOR OUT terminal outputs video and
Air signal
audio of CABLE/AIR and INPUTS 1, 2, 3, 4 and 5. It
does not output component and HDMI video.
1. Connecting S-Video: Connect the cable from the S-VIDEO OUT of the Rear Panel to the INPUT (S-VIDEO) jack,
of the VCR .
Connecting Video: Connect the cable from the VIDEO INPUT of
the VCR to the VIDEO out jack on the TV Rear Panel.
2. Connect the cable from the AUDIO IN R of the
VCR to the OUTPUT (AUDIO/R) jack on the TV Rear Panel.
3. Connect the cable from the AUDIO IN L of the
VCR to the OUTPUT (AUDIO/L) jack on the TV Rear Panel.
VCR or other external
NOTE: When making video connections, connect S-Video only or Video only. If both are connected, S-
Video takes priority.
Stereo System Amplifier
OPTICAL
IN
Stereo System Amplifier
or DVD Player
Optional
R L V
S-VIDEO
INPUT
components
21
Connecting External Video Sources
First time use
Your HITACHI LCD Television is equipped with a G-LINK feature. This connection is necessary for the TV
Guide On Screen
TM
system to work with your cable box to receive program listings and to enable VCR
recording features. Once you setup the G-LINK (IR Blaster) connector, then you can use your HITACHI LCD TV Remote Control and the TV Guide On Screen system to control your cable box and VCR
recording features.
The LCD Television Rear Panel has IR OUT/G-LINK terminals. One IR Blaster cable can connect up to
2 external Audio/Video components. Please see the following example of a G-LINK setup between your
HITACHI LCD Television and external Audio/Video equipment (VCR and Cable box).
CONNECTING THE CABLE BOX/VCR TO G-LINK FOR TV GUIDE ON SCREEN
TM
SYSTEM
1. Connect your external Audio/Video components to the Rear Panel shown below.
2. Connect the IR Blaster cable to the IR OUT/G-LINK output terminal of the Rear Panel.
3. Place the IR Blaster in front of the infrared sensor of the external components you want to control.
4. To access the TV Guide On-ScreenTMsystem, press the MENU button.
5. Use the CURSOR PAD or channel scroll down to highlight TV GUIDE ON SCREEN.
6. Press the SELECT or CURSOR PAD button to select.
7. Follow the Setup procedure on pages 49-51.
NOTE:
G-LINK connections are available on both IR OUT terminals.
Infrared Sensor
IR
Blaster
V L R
OUTPUT
VCR
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move
SEL
Select
Infrared Sensor
YP
Cable Box
OUTPUT
B/CBPR/CR
R L
22
The Remote Control
In addition to controlling all the functions on your
HITACHI LCD TV, the new remote control is
designed to operate different types of VCRs, CATV (Cable TV) converters, set-top-box, satellite receiver, DVD players, and other audio/video equipment with one touch. Basic operation keys are grouped together in one area.
To operate your LCD TV, point the remote
control at the remote sensor of the television and select the TV by pressing the  or  button of the Source Access on the remote. The TV mode indicator will blink, indicating that the remote will now control your television.
To operate your VCR, point the remote at the remote sensor of the VCR and select PVR by pressing the  or  button of the Source Access on the remote. The PVR mode indicator will blink, indicating that the remote will now control your
VCR (see page 36 for instructions on how to
program the remote to control your VCR).
To operate your PVR (Personal Video Recorder), point the remote at the remote sensor of the PVR and select PVR by pressing the  or  button of the Source Access on the remote. The PVR mode indicator will blink, indicating that the remote will
now control your PVR (see page 36 for instruction
on how to program the remote to control your PVR).
To operate your cable box, point the remote at the remote sensor of the cable box and select the CABLE (CBL) by pressing the  or  button of the Source Access on the remote. The CBL mode indicator will blink, indicating that the remote will
now control your cable box (see page 33 for
instructions on how to program the remote to control your cable box).
To operate your set-top-box or satellite receiver point the remote at the remote sensor of the set­top-box and select the SET-TOP-BOX (STB) by pressing the  or  button of the Source Access on the remote. If you have a satellite receiver, use this button to program your satellite receiver. The STB mode indicator will blink, indicating that the remote will now control your set-top-box (see
page 34 for instructions on how to program the
remote to control your set-top-box).
To operate additional audio equipment, point the remote at the remote sensor of the component you wish to control and select AMP by pressing the or button of the Source Access on the remote. The AMP mode indicator will blink, indicating that the remote will now control your audio equipment
(see page 37 for instructions on how to program
the remote to control additional Audio/Video equipment).
There are two modes of illuminating the Remote Control buttons. They are the Automatic and Manual modes.
AUTOMATIC MODE (Optional mode)
In Automatic mode, if any button is pressed (including the LIGHT button), the illumination will last for 4 seconds.
MANUAL MODE (Default mode)
In Manual mode, the illumination will only work when the LIGHT button is pressed. When the LIGHT button is pressed, the illumination will last for 8 seconds. During the illumina­tion, if the LIGHT button is pressed, the illumination will turn off.
CHANGING LIGHTING MODES (Automatic to Manual/Manual to Automatic)
1. Place the Remote Control in TV Mode by using the SOURCE ACCESS indicator will blink 3 times to confirm the remote control mode.
2. Press and hold the LIGHT button for 10 seconds. After releasing the LIGHT button, the TV mode indicator will blink 3 times to confirm the mode switch.
NOTE: When you press any remote control button,
the buttons will light up. The illumination will last a few seconds during this time. The buttons will appear illuminated if the room is dark.
and buttons. The TV mode
A/V NET
+
-
/
The Remote Control
To operate your DVD player, point the remote at the remote sensor of the DVD player and select DVD by pressing the  or  button of the Source Access on the remote. The DVD mode indicator will blink, indicating that the remote will now
control your DVD Player (see page 35 for
instruction on how to program the remote to control your DVD player).
23
How to Use the Remote to Control Your TV
POWER button
Press this button to turn the TV set on or off when
the remote is in TV mode. (See page 23 for
햷 햸
+
-
instructions on how to set the remote control to TV mode.)
MODE Indicator
Turns on or blinks to show remote control mode.
SOURCE ACCESS (or ) buttons
Press these buttons to select remote control mode.
SOURCE ACCESS (ENT) button
Hold down this button while entering your device
code to program the remote (see pages 33-38).
You can also use this button in an optional Input
access feature (see page 38).
PAUSE button
Press the PAUSE button to freeze the picture. Press the EXIT button to return the picture to motion. Press the PAUSEbutton repeatedly to cycle through the three different freeze modes
(see page 32).
The Remote Control
/
Freeze
Freeze
Freeze
Freeze
24
Freeze
How to Use the Remote to Control Your TV
ASPECT button
Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal format received, the picture format ratio allows you to adjust the images through the following options.
4:3 STANDARD
Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the left and right of the image to preserve the original aspect ratio of the source.
4:3 EXPANDED
Use this aspect mode to display conventional (4:3) sources by linearly increasing image expansion from the center towards the edges of the display area in order to fill it.
Antenna-Analog Channel
S-Video/Video Input
(Auto Aspect: Off)
HDMI-480i/480p Input (Auto Aspect: Off)
IMA GE INPUT
Component-480i/480p Input (Auto Aspect: Off)
Note: Please see Appendix A
on page 88.
Antenna-Digital Channel (4:3)
S-Video/Video 4:3/Letter
Input (Auto Aspect: On)
HDMI-480i/480p 4:3/
Letter Input (Auto Aspect: On)
Component-480i/480p 4:3/
IMA GE INPUT
Letter Input (Auto Aspect: On)
4:3 ZOOM1/ZOOM2
Use these aspect modes to zoom in on conventional (4:3) sources.
16:9 STANDARD 1
Use this aspect mode to display 16:9 sources like
HDTV and DVD’s preserving the original 16:9 aspect ratio showing 95% of the size.
16:9 STANDARD 2
Use this aspect mode to display 16:9 sources like HDTV and DVD’s preserving the original 16:9 aspect ratio showing 100% of the size.
16:9 ZOOM
Use this aspect to Zoom-in once while in 16:9 aspect.
1
The Remote Control
Note: Please see Appendix A
on page 88.
S-Video/Video 16:9 Input
(Auto Aspect: On)
HDMI-480i/480p 16:9 Input
(Auto Aspect: On)
Component-480i/480p
IMA GE INPUT
1
16:9 Input (Auto Aspect: On)
Note: Please see Appendix A
on page 88.
Antenna-Digital Channel (16:9)
HDMI-720p/1080i Input
Component-720p/1080i
Input
IMA GE INPUT
1
Note: Please see Appendix A
on page 88.
NOTE: 1. The Aspect Style in all five video inputs have independent Aspect Style setting.
2. Vertical position adjustments are directly available when you choose 4:3
EXPANDED/ZOOM1/ZOOM2 or 16:9 ZOOM aspect style (see also page 46)..
3. When displaying 16:9 STANDARD 2 it may appear lines at the edge of the picture this is normal operation of the TV.
2
25
How to Use the Remote to Control Your TV
When a Component Video: Y-PbPr
Input is connected to INPUT 3
DAY/NIGHT button
Press this button to toggle between Day(Normal), Day(Dynamic) and Night picture mode settings. Select Day modes for day time viewing with more brightness and contrast to compete with room light. Select Night for nighttime viewing with less brightness
and contrast for a more detailed picture (see page 43
for settings changes).
INFO
480i 3:17PM
Input Signal
Format
Y-PBPR: 3
The Remote Control
NOTE: For automatic DAY/NIGHT picture mode
settings, see page 61.
PICTURE-IN-PICTURE button
See separate section on pages 30-31 for a
description.
MENU button
The MENU button will start the On-Screen Display.
INFO button
Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second audio program (SAP), the time, CHANNEL ID and if the TIMER is set.
ANALOG CHANNELS
Program Information
Program Run Time
INFO
Program Information
Program Run Time
INFO
Show Name Air 8
3:00PM-
3:30PM KXYZ-HD
ST TV-G 480i 3:17PM
Audio
Broadcast
Auto STEREO
Closed
Caption setting
DIGITAL CHANNELS
Show Name Air 15-1
3:00PM-
ST 1080i 3:17PM
Audio
Broadcast
Auto
Closed
Caption setting
Broadcast
Rating
Audio Source
Selection
Digital Closed Caption
This icon will appear only when
receiving a Digital Broadcast with
Closed Captioning.
ALT U.S.
3:30PM KPBS-HD
TV-G DTvCC
Broadcast
Alternate
Rating
Rating
Program Desctiption
(Press INFO again for a more detailed description)
When an S-VIDEO Input is connected
to INPUT 1
INFO
Auto
NOTE: 1. The Sleep Timer info will show
momentarily after releasing INFO button.
2. The Aspect setting will not be shown if the channel is locked.
Picture Format
Picture Format
480i 3:17PM
S-IN: 1
Main Picture Source and channel indication
Broadcast channel identication Clock
Main Picture Source and channel indication
Broadcast channel identication Clock
Auto
EXIT button
This button will exit all On-Screen Displays.
CURSOR PAD/SELECT button
All the On-Screen Display features can be set or adjusted by using the CURSOR PAD, except for numeric entries. The CURSOR PAD will highlight functions or adjust and set different features. Press the CURSOR PAD toward desired direction and press the SELECT button to select.
GUIDE button
Press this button to access the TV Guide On
TM
Screen
interactive display (see page 49). Press
this button to access the Channel Guide of the (CBL), and (SAT/STB) while in (CBL)(SAT/STB) mode.
INPUTS button
When the remote control is in TV mode, press this button to access the INPUTS menu. Use the CURSOR PAD and SELECT button to select the inputs that are being used. Pressing the INPUTS button repeatedly will also cycle through the Inputs menu items. Then press the SELECT button to select.
Input 5
Photo Input
Cable
Air /
Input 1 Input 2
Move SEL Sel.
INPUT 1 Select to choose INPUT 1. INPUT 2 Select to choose INPUT 2.
INPUT 3 Select to choose INPUT 3. INPUT 4 Select to choose INPUT 4. INPUT 5 Select to choose INPUT 5.
CABLE Select between Cable or Air signal.AIR /
PHOTO INPUT Select to access your pictures from a
digital camera, USB memory or memory card USB drive connected to the Photo Input in the side panel of
the TV (see pages 27-28).
26
How to Use the Remote to Control Your TV
PHOTO INPUT
This feature is useful for viewing digital still pictures from your digital camera, USB Drive or memory cards USB drive using the Photo Input in the left side panel of the TV.
1. Press the INPUTS button to cycle through the INPUTS selections until the PHOTO INPUT is selected. Press the SELECT button or CURSOR PAD .
Input 5 Photo Input
Cable
Air /
Input 1 Input 2
Move SEL Sel.
2. Press the CURSOR PAD  or  to access the next or previous photo.
SEL Thumbnail [0-9] Jump
Next
The Remote Control
3. Press the SELECT button to view THUMBNAIL.
4. Use the CURSOR PAD buttons , ,  or  and the SELECT button to navigate and select individual chosen photos.
5. Press the picture number to jump from picture to picture.
6. Press the INFO button to access PHOTO Input menu and to view Photo information.
7. Press the CURSOR PAD  or  and the SELECT button to navigate and select the PHOTO Input menu.
Please Enter
Picture Number
--
Picture No.
Resolution
File Name
Rotate Slideshow Device
No. 02/08
Date
06/13/05 2048x1536 DSC00467
NOTES: 1. Contrast will decrease automatically if stationary images such as digital still photos are left
on the screen for more than 3 minutes.
2. The maximum number of digital Photos that can be displayed is 999.
3. Press INFO button to show Picture Numbers in Thumbnail view, plus other information in individual photos.
4. Digital photos recorded on a DVD-RAM disc may not work with this Photo Input.
5. Certain types of digital cameras may not work with this Photo Input.
6. Digital cameras with low battery power may not properly display your photos in this input.
7. The screen may show “Input device not detected” if the digital camera’s large capacity memory is fully loaded, or because of slow access time on some digital cameras. Please wait 1 or 2 minutes before checking your Photo Input connections.
27
The Remote Control
How to Use the Remote to Control Your TV
ROTATE
Select this menu item to rotate selected photos either clockwise (CURSORPAD ) and counterclockwise (CURSOR PAD ).
SLIDESHOW
Select this menu item to start a slideshow of the digital photos. While the Interval sub menu is highlighted, press the SELECT button to cycle through the interval time from 5, 10 and 30 seconds. Press the SELECT button to stop on a chosen picture of the slideshow. After 30 seconds, the slideshow will resume or press the SELECT button again to continue with the slideshow.
DEVICE
Select this menu item to select the Photo Input Device Drive when using a USB Drive device. Use the CURSOR PAD  or  to select Device Drive. Press the INFO button to highlight a device, then press the SELECT button or CURSOR PAD  to access it. Use the CURSORPAD or to the device to read.
Rotate Slideshow Start Device Interval 30sec
Rotate Slideshow Device Drive B
 
NOTES: 1. Automatic contrast reduction also applies during SLIDESHOW, then press any button to
continue.
2. Photo file names modified on a computer should be 8 characters (Ex. ABCD1234.jpg). 1st four characters: Letters; 5th to 8th: Non duplicated numbers from 0001 to 9999. Photo files should be first placed on a sub directory name with 8 characters (Ex. 123ABCDE). 1st to 3rd: Non­duplicated numbers from 0001 to 9999 4th to 8th: Letters. The sub directory then should be placed on a main directory with a “dcim” file name format.
3. Supported image types are up to 3072 x 2304; JPEG format should conform with DCF Standard (Design rule for Camera File System).
4. This TV set displays only digital pictures from digital cameras which meet DCF Standard. Pictures that were copied, edited or modified on a computer may not be displayed on the TV set.
28
How to Use the Remote to Control Your TV
( CH-)
LAST CHANNEL (LAST CH) button
Press this button to toggle between the current and last channel viewed.
VOLUME (VOL) WHEEL, MUTE button
Use the VOL WHEEL ( or ) until you obtain the desired sound level.
To reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc., press the VOL wheel down. Press the VOL wheel again to turn the sound off completely (MUTE). To restore the sound, press the VOL wheel one more time or VOL Up ().
Volume 8
When using the Cursor up or down
(CH+ or CH-)
to change channel it will operate same as the
CHANNEL WHEEL except for the (FAV) channel setting. The cursor up or down can only change channels ; but to activate the (FAV) channels it has to be activated from the CHANNEL WHEEL only.
Press the channel (CH) wheel to switch to Favorite (FAV) channel mode.You will know you are in Favorite Channel mode when (FAV) is displayed and the displayed channel is GREEN. Press it again to return to your regular tuned channels.You can add any channel to your Favorite channel list by pressing and holding down the Channel (CH) wheel until the displayed channel turns from WHITE to highlighted GREEN.You can also delete a channel from your favorite channel list by pressing and holding down the Channel (CH) wheel until the displayed channel turns highlighted GREEN to WHITE.
Cable 22
The Remote Control
Soft Mute 8
Mute 8
Closed Captioning will display automatically when MUTE/SOFT MUTE is on and Closed Caption is set
to AUTO (see page 65).
When the TV power is turned off at a volume level 31 or greater, the volume level will default to 30 when the TV is turned on. However, if it is set to a level 30 or less, the volume level will be at the level it was set when the TV is turned ON.
CHANNEL (CH) WHEEL/CHANNEL SELECTOR
buttons
The CHANNEL wheel or the CHANNEL SELECTOR buttons are used to select channels, lock access code, etc. Use the CHANNEL WHEEL ( or ) to select the desired channel. Use the CHANNEL SELECTOR buttons to enter one, two, or three numbers to select channels. Enter “0” first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune. For Digital Channels, use the CHANNEL SELECTOR buttons with the (-) DASH button. Channel selection may also be performed by CHANNEL WHEEL up () , CHANNEL WHEEL down () or CURSOR up & Cursor down .
( CH+)
/
FAV Cable 22
Cable 22
/
(-) DASH button
Use the (-) DASHbutton with the CHANNEL SELECTOR buttons to enter Digital Channels that have subchannel numbers indicated by (-) DASH (example 15-1).
BACKLIGHT button
Press this button to light up and illuminate the buttons of the remote control.
29
Picture-in-Picture (PIP)
Your HITACHI LCD TV incorporates one Tuner technology designed for improved viewing enjoyment. This feature allows you to view Digital Channels and Video inputs on both the main picture and sub picture simultaneously, with separate control. When a Digital channel is viewed in the main picture, the Digital or Analog channel can not be viewed in the sub picture. Please see table for PIP availability.
To select between main picture and PIP sub picture, use the CURSOR PAD button on the remote. The Green highlighted PIP square will move with every press of the CURSOR PAD buttons.
The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing other programs from any of the video inputs.
CABLE
or
Air signal
The Remote Control
Use connection at right to view VCR program as a sub­picture while viewing another program as main picture (CABLE/AIR Digital channel).
PIP button
Press the PIP button and a sub-picture will appear in one of the four different modes (POP, PIP, or SPLIT), depending on the INPUT signal. To change the PIP mode, use the PIP button to cycle through the three different modes.
SPLIT MODE PICTURE-IN-PICTURE
Split Mode PIP displays the main picture and sub-
picture evenly on the screen.
SWAP
Main Picture
Sub Picture
POP MODE PICTURE-IN-PICTURE
POP Mode PIP displays the sub-picture outside of the main picture. Use the CURSOR PAD ( or ) to move the sub-picture. This feature is not available with a 1080i/720p signal. Please refer to the PICTURE-IN-PICTURE MODES Table (see page
31).
Main Picture
Back of
AUDIO OUT VIDEO OUT
VCR
OUTPUT
VCR
+
-
Sub Picture
SWAP
NOTE : 1. Press the CURSOR PAD ( or ) to
enable the sub-picture sound.
30
Picture-In-Picture (PIP)
PIP MODE PICTURE-IN-PICTURE
Select CABLE/AIR or INPUT 1~5 from the INPUTS menu. Select a channel that has a 1080i/720p signal.
Main Picture
PIP Specifications Table
Sub Picture
PIP
Mode
Main Picture
POP
PIP 16x9
PIP 4x3
SPLIT
STROBE
(4pix)
Yes* l: Auto Aspect OFF
Yes*2: Aulo Aspect ON
( - ) : Not available
Digital Ch.
(Air or Cable)
Component Composite S-IN HDMI
Digital Ch.
(Air or Cable)
Component Composite. S-IN HDMI
Digital Ch.
(Air or Cable)
Componet Composite S-IN HDMI
Digital Ch.
(Air or Cable)
Component Cmposite S-IN HDMI
Digital Ch.
(Air or Cable)
Component Composite S-IN HDMI
1080i 16x9
720p 16x9
480p 16x9
480p 4x3
480i 16x9
480i 4x3
1080i 16x9
720p 16x9
480p 16x9
480p 4x3
480i 16x9
480i 4x3
1080i 16x9
720p 16x9
480p 16x9
480p 4x3
480i 16x9
480i 4x3
1080i 16x9
720p 16x9
480p 16x9
480p 4x3
480i 16x9
480i 4x3
1080i 16x9
720p 16x9
480p 16x9
480p 4x3
480i 16x9
480i 4x3
1080i 16x9
720p 16x9
480p 16x9
480p 4x3
480i 16x9
480i 4x3
1080i 16x9
720p 16x9
480p 16x9
480p 4x3
480i 16x9
480i 4x3
1080i 16x9
720p 16x9
480p 16x9
480p 4x3
480i 16x9
480i 4x3
1080i 16x9
720 p 16x9
480p 16x9
480p 4x3
480i 16x9
480i 4x3
1080i 16x9
720p 16x9
480p 16x9
480p 4x3
480i 16x9
480i 4x3
SWAP
Digital Channel
1080i 720p 480p 480p 480i 480i 1080i 720p 480p 480p 480i 480i
16x9 16x9 16x9 4x3 16x9 4x3 16x9 16x9 16x9 4x3 16x9 4x3
----- ---- -- -
----- ---- -- -
----- ---- -- -
- - - - - - Yes Yes Yes Yes Yes Yes
----- ---- -- -
- - - - - - Yes Yes Yes Yes Yes Yes
----------- -
----- ---- -- -
Yes*l Yes*l Yes*l Yes*l Yes*l Yes*l - - - - - -
Yes Yes Yes Yes Yes Yes - - - - - -
Yes*l Yes*l Yes*l Yes*l Yes*l Yes*l - - - - - -
Yes Yes Yes Yes Yes Yes - - - - - -
- - - - - - Yes Yes Yes*2 - Yes*2 -
- - - - - - Yes Yes Yes*2 - Yes*2 -
- - - - - - Yes Yes Yes*2 - Yes*2 -
----- ---- -- -
- - - - - - Yes Yes Yes*2 - Yes*2 -
----- ---- -- -
Yes Yes Yes - Yes - - - - - - -
Yes Yes Yes - Yes - - - - - - -
Yes*2 Yes*2 Yes*2 - Yes*2 - - - - - - -
——— - — - - - - - - -
Yes*2 Yes*2 Yes*2 - Yes*2 - - - - - - -
----_------ -
- - - - _ - - - Yes*l Yes Yes*l Yes
- - - - - - - - Yes*l Yes Yes*l Yes
- - - - - - - - Yes*l Yes Yes*l Yes
----- ---- -- -
- - - - - - - - Yes*l Yes Yes*l Yes
- - - Yes - Yes - - - - - -
- - - Yes - Yes - - - - - -
- - - Yes*2 - Yes*2 - - - - - -
----- ---- -- -
- - - Yes*2 - Yes*2 - - - - - -
----- ---- -- -
- - - - - - Yes Yes Yes Yes Yes Yes
- - - - - - Yes Yes Yes Yes Yes Yes
- - - - - - Yes Yes Yes Yes Yes Yes
- - - - - - Yes Yes Yes Yes Yes Yes
- - - - - - Yes Yes Yes Yes Yes Yes
- - - - - - Yes Yes Yes Yes Yes Yes
Yes Yes Yes Yes Yes Yes - - - - - -
Yes Yes Yes Yes Yes Yes - - - - - -
Yes Yes Yes Yes Yes Yes - - - - - -
Yes Yes Yes Yes Yes Yes - - - - - -
Yes Yes Yes Yes Yes Yes - - - - - -
Yes Yes Yes Yes Yes Yes - - - - - -
Yes----- ----- -
-Yes------ --- -
--Yes---------
---Yes--------
----Yes--- --- -
-----Yes-- --- -
----- -Yes_--- -
----- --Yes--- -
----- ---Yes-- -
---------Yes--
----------Yes-
----- ---- --Yes
Component/Composite/S-lN/HDMI
Sub Picture
The Remote Control
31
Picture-In-Picture (PIP)
The Remote Control
PAUSE button
If you wish to freeze the sub-picture, press the PAUSE button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the EXIT button. Press the PAUSE button repeatedly to toggle between FREEZE modes (Main Freeze, SPLIT and STROBE).
Freeze
Freeze
Freeze Freeze
Freeze
SPLIT FREEZE
Press the PAUSE button to freeze the picture you are currently viewing (only the right sub-picture will freeze). Press the EXIT button to return to normal viewing.
Main Picture
STROBE FREEZE
Press the PAUSE button to freeze three frames of the picture you are currently viewing (only the 3 sub-pictures will freeze). Press the EXIT button to return to normal viewing. This feature is useful for viewing a moving picture that has many details, for example, a close play in a sporting event or a golf swing.
Sub Picture
MAIN FREEZE
Press the PAUSE button to freeze one frame of the picture you are currently viewing and the frozen frame will show in the Main Picture. Press the EXIT button to return to normal viewing. This feature is useful for freezing a picture frame with addresses.
Hot Springs Clay Mask
C/O John Doe
Run-Spa Retreat
P.O. Box 55512
Any Town, USA 98765
Check or
Money Order Only
1-800-555-1212
NOTE: 1. The default FREEZE mode is the MAIN
freeze followed by the SPLIT freeze and then the STROBE freeze. The last FREEZE mode you selected before you pressed the EXIT button will be the one that comes up after pressing the PAUSE button again.
2. Each freeze frame in Strobe Freeze is delayed about 0.1 (1/10) second.
32
The Remote Control for Cable Box Functions
Operating the precoded function for your cable box.
This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of your cable box (refer to
pages 39-40 for pre-codes).
1. Turn ON your cable box.
2. Aim the remote control at the front of your cable box.
3. To switch to Cable (CBL) pre-coded mode, use the SOURCE ACCESS buttons ( or ) on the remote
control to position the LED light to the corresponding selection.
4. Hold down the ENT button on the remote and enter the four digit preset code that matches your cable
box as shown on pages 39-40. Release the ENT
button. The indicator light will flash 3 times if the code was accepted.
5. Aim the remote at the cable box and press the POWER button. The remote will turn off your cable box when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different four digit preset code.
+
-
The Remote Control
/
6. The remote will now control your Cable box.
NOTE: 1. If your cable box cannot be operated after
performing the above procedures, your cable box code has not been precoded into the remote.
2. In the unlikely event that your cable box cannot be operated after performing the above procedures, please consult your cable box operating guide.
3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.
PRECODED CABLE BOX buttons
These buttons transmit the chosen precoded cable codes.
EXCLUSIVE TV buttons
These buttons are for operating the TV.
MY CABLE BOX CODE IS:
NOTE: Refer to instruction manual of the Cable Box
for operation of the buttons exclusively for the Cable Box.
33
The Remote Control for Set-Top-Box/Satellite Receiver
Functions
The Remote Control
Operating the precoded function for your set-top­box/satellite receiver.
This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set-
top-box/satellite systems (refer to pages 39-40 for pre-
codes).
1. Turn ON your set-top-box/satellite systems.
2. Aim the remote control at the front of your set-top­box/satellite systems.
3. To switch to set-top-box/satellite (STB) pre-coded mode, use the SOURCE ACCESS buttons ( or )
on the remote control to position the LED light to the corresponding selection.
4. Hold down the ENT button on the remote and enter the four digit preset code that matches your set-
top-box/satellite receiver as shown on page 39-40.
Release the ENT button. The indicator light will flash 3 times if the code was accepted.
5. Aim the remote at the set-top-box/satellite receiver and press the POWERbutton. The remote will turn off your set-top-box/satellite receiver when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your set-top-box/satellite receiver. If the set-top­box/satellite receiver does not turn off, try a different four digit preset code.
+
-
/
6. The remote will now control your set-top­box/satellite receiver.
NOTE: 1. If your set-top-box/satellite receiver
cannot be operated after performing the above procedures, your set-top-box/ satellite receiver code has not been precoded into the remote.
2. In the unlikely event that your set-top­box/satellite receiver cannot be operated after performing the above procedures, please consult your set-top-box/satellite receiver operating guide.
3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.
PRECODED SET-TOP-BOX/SATELLITE
RECEIVER buttons
These buttons transmit the chosen pre-coded set­top-box/satellite codes.
EXCLUSIVE TV buttons
These buttons are for operating the TV.
MY Satellite RECEIVER/ SET-TOP-BOX CODE IS:
NOTE: Refer to instruction manual of the Set-Top-
Box/Satellite Receiver for operation of the buttons exclusively for the Set-Top­Box/Satellite Receiver.
34
The Remote Control for DVD Functions
Operating the precoded function for your DVD player.
This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player (refer to
pages 39-40 for pre-codes).
1. Turn ON your DVD player.
2. Aim the remote control at the front of your DVD player.
3. To switch to DVD pre-coded mode, use the SOURCE ACCESS buttons ( or ) on the remote
control to position the LED light to the corresponding selection.
4. Hold down the ENT button on the remote and enter the four digit preset code that matches your DVD
player, as shown on pages 39-40. Release the
ENT button. The indicator light will flash 3 times if the code was accepted.
5. Aim the remote at the DVD player and press the POWER button. The remote will turn off your DVD player when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not turn off, try a different four digit preset code.
The Remote Control
+
-
/
6. The remote will now control your DVD player.
7. You will need to set the display type of your DVD player to 16:9 widescreen.
NOTE: 1. If your DVD player cannot be operated
after performing the above procedures, your DVD player code has not been precoded into the remote.
2. In the unlikely event that your DVD player cannot be operated after performing the above procedures, please consult your DVD player operating guide.
3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.
PRECODED DVD Buttons
These buttons transmit the chosen precoded DVD codes.
EXCLUSIVE TV Buttons
These buttons are for operating the TV.
MY DVD PLAYER CODE IS:
NOTE: Refer to instruction manual of the DVD Player
for operation of the buttons exclusively for the DVD Player.
35
The Remote for VCR/PVR Functions
Operating the precoded function for your VCR/PVR (Personal Video Recorder).
This remote is designed to operate different types of VCRs/PVRs. You must first program the remote to match the remote system of your VCR/PVR (refer to
pages 39-40 for pre-codes).
1. Turn ON your VCR/PVR.
2. Aim the remote control at the front of your VCR/PVR.
3. To switch to VCR/PVR pre-coded mode, use the SOURCE ACCESS buttons ( or ) on the remote
control to position the LED light to the corresponding selection.
4. Hold down the ENT button on the remote and enter the four digit preset code that matches your
VCR/PVR, as shown on pages 39-40. Release the
ENT button. The indicator light will flash 3 times if the code was accepted.
+
-
The Remote Control
5. Aim the remote at the VCR/PVR and press the POWER button. The remote will turn off your PVR when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your VCR/PVR. If the VCR/PVR does not turn off, try a different four digit preset code.
6. The remote will now control your VCR/PVR.
NOTE: 1. If your VCR/PVR cannot be operated after
performing the above procedures, your VCR/PVR code has not been precoded into the remote.
2. In the unlikely event that your VCR/PVR cannot be operated after performing the above procedures, please consult your VCR/PVR operating guide.
3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.
PRECODED VCR/PVR Buttons
These buttons transmit the chosen precoded VCR/PVR codes.
/
MY VCR/PVR CODE IS:
NOTE: Refer to instruction manual of the VCR/PVR
for operation of the buttons exclusively for the VCR/PVR.
EXCLUSIVE TV Buttons
These buttons are for operating the TV.
36
The Remote Control for Additional Audio Equipment
Operating the precoded function for your Audio component.
This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component
(refer to pages 39-40 for pre-codes).
1. Turn ON your Audio component you wish to control with the Remote.
2. Aim the remote control at the front of your Audio component.
3. To switch to Audio (AMP) component pre-coded mode, use the SOURCE ACCESS buttons ( or )
on the remote control to position the LED light to the corresponding selection.
4. Hold down the ENT button on the remote and enter the four digit preset code that matches your Audio
component, as shown on pages 39-40. Release
the ENT button. The indicator light will flash 3 times if the code was accepted.
5. Aim the remote at the Audio component and press the POWERbutton. The remote will turn off your Audio component when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio component does not turn off, try a different four digit preset code.
6. The remote will now control your Audio component.
7. Repeat steps 1 - 6 if you wish to program the remote to control another Audio component.
NOTE: 1. If your Audio component cannot be
operated after performing the above procedures, your Audio component code has not been precoded into the remote.
2. In the unlikely event that your Audio component cannot be operated after performing the above procedures, please consult your Audio component operating guide.
3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.
+
-
/
MY AUDIO COMPONENT CODE IS:
NOTE: Refer to instruction manual of the VCR/PVR
for operation of the buttons exclusively for the VCR/PVR.
The Remote Control
PRECODED AUDIO Buttons
These buttons transmit the chosen precoded Audio component codes.
EXCLUSIVE TV Buttons
These buttons are for operating the TV.
37
How to Use the ENT Button
INPUT ACCESS
This optional feature allows the user of the remote control to setup it’s ENTER (ENT) button to access the specified input of the TV. Setup for this feature is applicable to the remote control’s normal mode only and only applies to the DVD, CBL, STB, PVR and AMP modes.
1. Select the desired device mode (DVD, CBL, STB, PVR, or AMP) by using your SOURCE ACCESS buttons ( or ) to position the LED indicator to the corresponding selection.
2. Hold down the ENTER (ENT) button on the remote and enter the four digit preset code that
matches your device as shown on pages 39-40.
3. Then enter the assigned input number (1-5) that the device is related to.
4. Release ENTER (ENT) button.
5. If done correctly, the device LED indicator will flash 3 times to confirm proper setup.
, , 
, , 
+
-
/
The Remote Control
6. The remote will now control the desired device.
7. Pressing the ENTER (ENT) button will now access the video input (1-5) of the desired device.
SETUP EXAMPLE (Hitachi DVD with precode 0573 connected to INPUT 1 of the TV)
Select DVD mode by using your SOURCE ACCESS
buttons ( or ) to position the LED indicator to DVD.
Hold down the ENTER (ENT) button and press the
numbers 0, 5, 7 and 3.
Then press the number 1 for the assigned input
number of the DVD player.
Release ENTER (ENT) button.
If done correctly, the device LED indicator will flash
3 times to confirm proper setup.
The remote will now control the DVD player.
Press the ENTER (ENT) button to instantly access
the video input of your DVD on Input 1.
NOTE: 1. This feature is optional
2. Assigned input numbers can be used more than once if applicable.
38
Remote Control Codes
VCR BRAND ..................CODE
ABS ..................................1972
Admiral ....................0048, 0209
Adventura .........................0000
Aiko....................................0278
Aiwa ..............0000, 0037, 0307
Akai ..............0041, 0061, 0106
Alienware ..........................1972
America Action ..................0278
American High ..................0035
Asha ..................................0240
Audiovox..................0037, 0278
Beaumark ..........................0240
Bell & Howell ....................0104
Broksonic................0121, 0184,
......................0002, 0209, 0479
CCE ........................0072, 0278
Calix ..................................0037
Canon ................................0035
Carver................................0081
Cineral ..............................0278
Citizen......................0278, 0037
Colt ....................................0072
Craig ......................0037, 0072,
......................0047, 0240, 0271
Curtis Mathes ........0035, 0041,
................................0060, 0162
CyberPower ......................1972
Cybernex ..........................0240
Daewoo ........0278, 0045, 0561
Dell ....................................1972
Denon ................................0042
Durabrand................0039, 0038
Dynatech ..........................0000
Electrohome ......................0037
Electrophonic ....................0037
Emerex ..............................0032
Emerson0037, 0184, 000, 0121,
0043, 0209, 0002, 0278, 0061,
..0208, 0212, 0479, 0561, 1593
Fisher ............0104, 0047, 0066
Fuji ..........................0033, 0035
Funai........................0000, 1593
GE ................0035, 0060, 0240,
................................0202, 0761
Garrard ..............................0000
Gateway ..........................1972
Go Video ................0432, 0526
GoldStar ..................0037, 0038
Gradiente ................0000, 0008
HI-Q ..................................0047
HP......................................1972
Harley Davidson ................0000
Harman/Kardon ......0038, 0081
Harwood ............................0072
Headquarter ......................0046
Hewlett Packard ................1972
Hitachi 0000, 0041, 0042, 0105
Howard Computers............1972
Hughes Network Systems 0042
iBuy Power ........................1972
JVC................0067, 0041, 0008
Jensen ..............................0041
KEC ........................0037, 0278
KLH....................................0072
Kenwood ......0041, 0067, 0038
Kodak ......................0035, 0037
LG......................................0037
LXI ....................................0037
Lloyd's ....................0000, 0208
Logik ..................................0072
MEI ....................................0035
MGA ..............0043, 0240, 0061
MGN Technology ..............0240
MTC ........................0000, 0240
Magnasonic ......................0593
Magnavox ....0035, 0081, 0563,
0000, 0039, 0593
Magnin ..............................0240
Marantz....................0081, 0035
Marta ................................0037
Matsushita ....0035, 0162, 1162
Media Center PC ..............1972
Memorex ......0035, 0162, 0037,
..........0048, 0039, 0047, 0240,
..........0000, 0104, 0209, 0046,
..0307, 0479, 1037, 1162, 1262
Microsoft ............................1972
Mind ..................................1972
Minolta ....................0042, 0105
Mitsubishi .... 0061, 0043, 0067
Motorola ..................0035, 0048
Multitech ..................0000, 0072
NEC ....0038, 0041, 0067, 0104
Nikko..................................0037
Noblex ..............................0240
Northgate ..........................1972
Olympus ............................0035
Optimus ........0593, 1062, 0162,
..........0037, 0048, 0104, 0432,
......................1048, 1162, 1262
Optonica ............................0062
Orion....0184, 0209, 0002, 0479
Panasonic ....0162, 1062, 0035,
......................0616, 1162, 1262
Penney0035, 0037, 0240, 0042,
..........................................0038
Pentax ....................0042, 0105
Philco ..0035, 0209, 0479, 0561
Philips ..........0081, 0035, 0618,
......................1081, 1181, 0062
Pilot....................................0037
Pioneer ..............................0067
Polk Audio..........................0081
Profitronic ..........................0240
Proscan ........0060, 0202, 0761
Protec ................................0072
Pulsar ................................0039
Quarter ..............................0046
Quartz................................0046
Quasar ..........0035, 0162, 1162
RCA....0060, 0240, 0042, 0105,
............0106, 0202, 0761, 0880
Radio Shack ............0000, 1037
Radix ................................0037
Randex. ............................0037
Realistic........0035, 0037, 0048,
..........0047, 0000, 0104, 0046,
................................0062, 0066
ReplayTV ................0614, 0616
Runco ................................0039
STS....................................0042
Samsung ......0045, 0240, 0432
Sanky ......................0039, 0048
Sansui ..........0000, 0067, 0209,
............0041, 0479, 1479, 0271
Sanyo ..0047, 0240, 0104, 0046
Scott ............0184, 0045, 0121,
......................0043, 0210, 0212
Sears..0035, 0037, 0047, 0000,
0042, 0104, 1237, 0046, 0066,
..........................................0105
Semp. ................................0045
Sharp ............0048, 0848, 0062
Shintom ............................0072
Shogun ..............................0240
Singer ................................0072
Sonic Blue ..............0614, 0616
Sony ............0035, 0032, 0000,
............0033, 0636, 1032, 1972
Sylvania........0035, 0081, 0000,
......................0043, 0593, 1593
Symphonic ....0000, 0593, 1593
Systemax ..........................1972
TMK ........................0240, 0208
Tagar Systems ..................1972
Tatung................................0041
Teac ........................0000, 0041
Technics ..................0035, 0162
Teknika ..........0000, 0035, 0037
Thomas..............................0000
Tivo................0618, 0636, 1503
Toshiba ........0045, 0043, 0066,
..........0210, 0212, 0366, 0845,
............1008, 1145, 1503, 1972
Totevision ................0037, 0240
Touch ................................1972
Unitech ..............................0240
Vector ................................0045
Vector Research................0038
Video Concepts ......0045, 0061
Videomagic........................0037
Videosonic ........................0240
Viewsonic ..........................1972
Wards 0060, 0062, 0035, 0048,
..........0047, 0081, 0240, 0000,
......................0042, 0072, 0212
White Westinghouse..................
................................0072, 0209
XR-1000 ........0072, 0000, 0035
Yamaha ............................0038
ZT Group ..........................1972
Zenith 0039, 0000, 0209, 0033,
................................0479, 1479
DVD BRAND ..................CODE
AMW..................................0872
Aiwa ..................................0641
Allegro ..............................0869
Apex Digital ..0672, 0717, 0755,
0794, 0796, 0797, 1004, 1020,
..1056, 1061, 1100, 1915, 1937
Audiovox..................0790, 1072
Axion..................................1072
Blaupunkt ..........................0717
Blue Parade ......................0571
Brooksonic ........................0695
CAVS ................................1057
CineVision ..............0876, 0869
Classic ..............................1917
Coby ..................................1086
Curtis Mathes ....................1087
CyberHome ..0816, 1023, 1024
DVD2000 ..........................0521
Daewoo ..................0784, 0705,
......................0833, 0869, 1918
Denon......................0490, 0634
Dual ........................1068, 1085
Emerson ..................0591, 0675
Enterprise ..........................0591
Fisher ................................0670
Funai..................................0675
GE ................0522, 0717, 0815
GPX ........................0699, 0769
Gateway ............................1073
Go Video ......0744, 0715, 0783,
......................0833, 0869, 1075
Gradiente ..........................0651
Greenhill ............................0717
Grundig..............................0705
Harman/Kardon ................0702
Hitachi ..........0573, 0664, 0695
Hiteker ..............................0672
IRT ....................................0783
Initial ..................................0717
Integra ..............................0627
Hiteker ..............................0672
JBL ....................................0702
JVC......0623, 0558, 0867, 1901
KLH ..............0717, 0790, 1020
Kawasaki ..........................0790
Kenwood..................0490, 0534
Koss ..................................0651
Lasonic ..............................0798
Lite-On ..............................1058
Magnavox ..............0503, 0675,
................................1914, 1976
Marantz..............................0539
Memorex............................0695
Microsoft ............................0522
Mintek......................0717, 0839
Mitsubishi ................0521, 1521
Nesa ..................................0717
Norcent....................1003, 0872
Onkyo ......................0627, 0503
Oritron................................0651
Panasonic..........................0490
Philco ................................0790
Philips..0503, 0539, 0646, 0854
Pioneer ..........0525, 0571, 1902
Polaroid ..................1061, 1086
Polk Audio..........................0539
Proscan ............................0522
Qwestar ............................0651
RCA..............0522, 0571, 0717,
......................0790, 0822, 1974
Recco ................................0698
Rio ....................................0869
Rotel ..................................0623
Rowa ................................0823
Sampo ....................0698, 0752
Samsung ................0490, 0573,
......................0820, 0744, 1075
Sansui................................0695
Sanyo ............0670, 0695, 0873
Semp ................................0503
Sharp ......................0630, 0752
Shinsonic ................0533, 0839
Sonic Blue ........................0869
Sony ..................................0533
Sylvania ............................0675
Symphonic ........................0675
TYT....................................0705
Teac ..................................0790
Technics ............................0490
Theta Digital ......................0571
Tivo....................................1996
Toshiba ........0503, 0695, 1045,
......................1988, 1996, 2006
Tredex ....................0799, 0803
US Logic............................0839
Urban Concepts ................0503
Venturer ............................0790
XBox ..................................0522
Yamaha ........0490, 0545, 0539
Zenith ............0591, 0503, 0869
CABLE BRAND..............CODE
ABC ....0003, 0008, 0011, 0013,
................................0014, 0017
Allegro ....................0153, 0315
Americast ..........................0899
Antronix ..............................022
Archer..............022, 0153, 0797
Bell & Howel .....................0014
Bell South ..........................0899
Cabletenna ........................0022
Cableview ..........................0022
Century ..............................0153
Citizen......................0153, 0315
ClearMax ..........................0883
Clearmaster ......................0883
Colour Voice............0025, 0031
Comtronics ........................0040
Contec ..............................0019
Coolmax ............................0883
Digi ....................................0637
Director ..............................0476
Dumont ..............................0637
Emerson ............................0797
Everquest ................0015, 0040
Focus ................................0400
Garrard ..............................0153
Gemini ....................0015, 0797
General Instrument 0003, 0011,
......................0476, 0276, 0810
GoldStar ..................0040, 0144
Goodmind ..........................0797
Hamlin 0009, 0020, 0034, 0273
Hitachi................................0011
The Remote Control
39
Remote Control Codes
The Remote Control
Jasco ............0015, 0153, 0315
Jerrold ......... 0003, 0011, 0012,
0014, 0015, 0024, 0276, 0476,
..........................................0810
Memorex ...........................0000
Motorola ...... 0276, 0476, 0810,
......................1106, 1254, 1376
Movie Time ........................0063
Multivision..........................0012
NSC ..................................0063
Novaplex............................0618
Oak ....................................0019
Optimus ............................0021
Pace ........................0237, 1877
Panasonic......0000, 0021, 0107
Panther ..............................0637
Paragon ............................0000
Philips......................0305, 0317
Pioneer0023, 0025, 0031, 0153,
............0144, 0533, 0877, 1877
Popular Mechanics ............0400
Pulsar ................................0000
Quasar...............................0000
RCA ..................................0021
RadioShack ..0015, 0315, 0797,
..........................................0883
Recoton ............................0400
Regal .............0020, 0273, 0279
Rembrandt ........................0011
Runco ...............................0000
SL Marx ............................0040
Samsung .................0040, 0144
Scientific Atlanta ....0877, 0008,
......................0017, 0477, 1877
Signal ......................0015, 0040
Signature ..........................0011
Sony ..................................1006
Sprucer ..............................0021
Starcom ..................0003, 0015
Stargate ........0015, 0040, 0797
Starquest ..........................0015
Supercable ........................0276
Supermax ..........................0883
TFC....................................0310
TV86 ..................................0063
Tandy ................................0258
TeleCaption........................0221
Teleview ............................0040
Timeless ............................0040
Tocom......................0012, 0013
Torx....................................0003
Toshiba ..............................0000
Tristar ................................0883
Tusa ..................................0015
Unika ......................0022, 0153
Universal ......0022, 0153, 0191
V2 ......................................0883
ViewMaster........................0883
Viewstar ..................0063, 0258
Vision ................................0883
Vortex View........................0883
Zenith ..0000, 0054, 0525, 0899
Zentek................................0400
SATELLITE BRAND (Set-Top-
Box) ................................CODE
AlphaStar ..........................0772
Amway ....................0043, 0075
Astro Industries..................0095
BSR ..................................0095
Cable Innovations..............0554
Capetronic ........................0095
Century ..............................0856
Channel Master ......0018, 0212
Chapparral ....0053, 0209, 0216
Conifer ..............................0004
Crossdigital ........................1109
Curtis Mathes ......................061
DX Antenna ......................0041
DirecTV ........0392, 0566, 0639,
............1639, 1142, 0247, 0749,
..........1749, 0724, 0819, 1856,
............1076, 1109, 0099, 1052,
..1053, 1054, 1442, 1443, 1444
Dish Network System ......1005,
0775, 1170
DishPro....................1005, 0775
Drake ............0018, 0064, 0245
Echostar ......1005, 0775, 0148,
......................0269, 0280, 1170
Expressvu..........................0775
GE ....................................0566
GOI ....................................0775
General Instrument ..........0869,
................................0547, 0554
Gradiente ..........................0856
HTS ..................................0775
Hitachi................................0819
homecable ........................0238
Hughes Network Systems 1142,
..0749, 1749, 1442, 1443, 1444
Hytek ................................0095
IQ ......................................0210
IQ Prism ............................0210
Innova................................0099
Intersat ..............................0043
JVC ..........................0775, 1170
Janeil ................................0152
Legend ..............................0269
Macom ....................0018, 0061
Magnavox................0724, 0722
Memorex..................0724, 0269
Mitsubishi ..........................0749
Motorola ............................0869
Netsat ................................0099
Next Level..........................0869
Norsat ................................0004
Pace ..................................0455
Panasonic......0247, 0701, 0152
Paysat................................0724
Philips 1142, 0749, 0724, 1076,
............0722, 1749, 0856, 0099
Pico....................................0075
Proscan ..................0392, 0566
RCA ....0392, 0566, 0855, 0143
Radioshack..............0869, 0554
Ramsey ............................0075
Realistic ............................0052
SKY ..............0856, 1856, 0099
STS..........................0041, 0210
Samsung..................1276, 1109
Sony ........................0639, 1639
Star Choice........................0869
Star Trak........0180, 0421, 0547
Strong ................................0421
Tivo......1142, 1442, 1443, 1444
Toshiba ........0749, 1749, 0790,
..........0061, 0082, 1052, 1053,
..1054, 1285, 1286, 1287, 1289
Town & Country ................0547
Uniden0724, 0722, 0052, 0074,
............0076, 0238, 0370, 0554
Zenith ..0856, 1856, 0061, 0064
AMPLIFIER BRAND ......CODE
Aiwa...................................0406
Bose ..................................0674
Carver................................0269
Curtis Mathes ...................0300
Denon ...............................0160
Durabrand..........................1561
GE .....................................0078
Harman/Kardon .................0892
JVC ...................................0331
Left Coast ..........................0892
Lenoxx ..............................1561
Linn ...................................0269
Luxman..............................0165
Magnavox ..........................0269
Marantz ........0269, 0321, 0892
NEC ..................................0264
Nakamichi..........................0321
Optimus ..................0395, 0300
Panasonic................0308, 0521
Parasound ........................0246
Philips......................0269, 0892
Pioneer ....................0013, 0300
Polk Audio ..............0269, 0892
RCA ..................................0300
Realistic .............................0395
Sansui................................0321
Shure ................................0264
Sony ..............0815, 0689, 0220
Soundesign..............0078, 0211
Technics ..................0308, 0521
Toshiba ..............................0353
Victor ................................0331
Wards ............0013, 0078, 0211
Yamaha ..................0354, 0133
RECEIVER BRAND (Amplifier) CODE
ADC ..................................0531
Aiwa....1405, 0121, 0158, 0189,
0405
Anam ......................1074, 1609
Arcam ................................1120
Audiotronic ........................1189
Bose ..............0639, 1229, 1253
Capetronic .........................0531
Carver............1189, 0042, 0189
Casio ................................0195
Clarinette ..........................0195
Coby ..................................1263
Compaq ............................1136
Curtis Mathes ....................0080
Dell ....................................1383
Denon .....................0004, 1360
Fisher ................................0042
Garrard ..............................0463
Glory Horse ......................1263
Harman/Kardon ......0891, 0110,
0189
Hewlett Packard ................1181
Hitachi................................0228
Integra ..............................0135
JBL ....................................0110
JVC..........................0074, 1263
KLH....................................1428
Kenwood ......1313, 1570, 1569,
............0027, 0042, 0186, 0239
LXI ....................................0181
Linn ...................................0189
Lloyd's................................0195
MCS ..................................0039
Magnavox ....1189, 1269, 0189,
0195, 0391, 0531 Marantz1189, 0039, 0189, 1269
Mitsubishi ..........................1393
Modulaire ..........................0195
Musicmagic........................1089
Nakamichi..........................0097
Onkyo ......................0135, 0842
Optimus ........1023, 0042, 0080,
..........0177, 0181, 0186, 0219,
..0531, 0670, 0738, 0801, 1074
Panasonic ....1518, 0039, 0309,
0367
Penney ..............................0195
Philips ..........1189, 1269, 0189,
................................0391, 1120
Pioneer ........1023, 0014, 0080,
............0150, 0244, 0531, 0630
Polk Audio..........................0189
Proscan ............................1254
Quasar ..............................0039
RCA..............1023, 1254, 0080,
......................0531, 1074, 1609
Radio Shack ......................1263
Realistic ..................0181, 0195
Rio ....................................1383
Sansui................................0189
Sanyo ......................0801, 1251
Scott ........................0163, 0322
Sharp ................................0186
Sharper Image ..................1263
Sherwood ................0491, 0502
Sonic Blue ........................1383
Sony ..1058, 1441, 1759, 0158,
............0474, 1349, 1406, 1442
Soundesign........................0670
Stereophonics....................1023
Sunfire ..............................1313
Teac ........................0463, 1074
Technics..................1308, 1518,
................................0039, 0309
Thorens..............................1189
Toshiba ..............................1572
Victor ................................0074
Wards .0014, 0080, 0158, 0189
Yamaha..........0176, 0186, 1176
Yorx. ..................................0195
Zenith ................................0857
AUDIO BRAND ..............CODE
Aiwa ........................0010, 0159
AudioSource ......................0351
Cambridge Soundworks ....0351
Carver................................0351
Fisher ................................0052
Fosgate..............................0259
Harmon/Kardon ................0477
JBL ....................................0477
JVC....................................0073
KLH....................................0351
Magnavox ..........................0325
Nikko..................................0376
Paramount Pictures 0317, 0351
RCA ..................................0056
SSI ....................................0317
Sansui................................0325
Schneider ..........................0376
Sony ........................0010, 0576
Soundesign........................0376
Yorx....................................0376
SET TOP BOX BRAND..CODE
Panasonic ..........................1120
Pioneer ..............................1010
Princeton..................0113, 0295
Samsung............................1190
Sensory Science................1126
Sharp ................................1010
Sony ..................................0639
PERSONAL VIDEO
RECORDER BRAND......CODE
Panasonic..........................0616
Philips ................................0618
ReplayTV ................0614, 0616
SonicBlue ................0614, 0616
Sony ..................................0636
Tivo..........................0618, 0636
40
On-Screen Display
1. Press MENU on the remote control to display the
different features on your HITACHI LCD TV.
2. Use the CURSOR PAD (buttons , ,  and ) or CHANNEL WHEEL to navigate to a different menu item.
3. Press EXIT on the remote control to quickly exit from a menu.
This part of the screen shows which selections are available.
Vide o
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move SEL Select
This part of the screen shows which Remote Control buttons to use.
Video
Picture Mode Select between 3 pictures modes;
Day (Dynamic), Day (Normal) and Night.
White Level Adjust picture white level. Black Level Adjust picture black level.
Color Adjust color. Tint Adjust tint. Sharpness Adjust sharpness.
Motion Sharpness Select between 3 sharpness modes
to increase detail on moving pictures.
Back Light Adjust the intensity of the panel back
light.
Color Temperature Set this to High for less intense
color with more blue, set to Medium for natural color, set to Standard for standard colors or Black and White for more reddish color.
Black Enhancement Enhance picture brightness in
light scenes.
Contrast Mode Use this function to choose
between 2 Contrast Mode
settings.
Noise Reduction Reduces conspicuous noise in
the picture.
Auto Movie Mode Turn On/Off the 3:2 Pulldown
detection feature.
Color Management Adjust and balance individual
colors to make either deeper or more pure according to preference.
Color Decoding Adjust the percentage of Red,
Green and Color according to preference.
Auto Color The AUTO COLOR function
automatically monitors and adjusts the color to maintain constant color levels even after a program or channel changes. It also maintains natural flesh tones while preserving fidelity of background colors.
White Balance Use this function to adjust the
dark end (Cutoff) and bright end (drive) of the White background.
Black Side Panel Set the gray side bars On/Off
when watching 4:3 signals in standard mode.
Aspect Choose the picture format
aspect ratio.
Reset Video Settings Choose to Reset Video Settings
to factory settings.
On-Screen Display
41
TV Guide On Screen Set, Control and navigate the
system
Signal Meter Access Signal Meter. Auto Channel Scan Set Auto Channel Scan. Channel List Set Channel List.
Unlocked Power Swivel enabled. Control
the motorized Table Top Stand
Locked Power Swivel disabled.
NOTE: 1. The Signal Meter feature of the Channel
Manager OSD is only available for Digital
channels.
2. The CableCARD information feature of the Setup OSD is only available when a CableCARD from your cable operator is installed in the rear panel of the TV.
3. Power Swivel feature is only available when Table Top Stand is connected.
On-Screen Display
Audio
Treble Adjust the treble. Bass Adjust the bass. Balance Adjust the balance.
Surround Select Surround settings (Off,
Wide, Normal)
Bass Boost Select Bass Boost option ON or OFF.
Audio Source Select between three Audio
Sources.
Internal Speakers Select internal or external
speakers.
Auto Noise Cancel Eliminates the noise between
stations. Perfect Volume Adjust volume in fixed setting. Loudness Adjust Loudness. Language Select Language options if
available. Digital Output Select Optical Output options. DRC Select Dynamic Range
Compression to ON or OFF.
NOTE: The Language, Digital Output, and the
Dynamic Range Compression feature of the Audio OSD are only available for Digital channels.
Timers
Set the Clock Set Clock Settings. Set Sleep Timer Set Sleep Timer intervals
(30 min. intervals, 00:30-3:00).
Set Day/Night Timer Set Day/Night picture mode
settings.
Setup
Set The Menu Options Choose English, French, or
Spanish text and Background.
Set The Power Saving
Set The Inputs
Set The Closed Captions Feature to display dialogue/text. Set The Output Terminals Set Output source options.
CableCARD Information Access important CableCARD
Set The Quick Start Options Select the TV Quick Start Up
Reset The Software Select to upgrade TV software.
Automatic Power Saving
features.
Label Video Inputs, VCR, DVD,
etc.
and Diagnostics info.
options.
TV Guide On Screen
Channel Manager
On-Screen Display
Locks
Change Access Code Change Lock access code. Engage Lock Choose to lock channel,
Movie Ratings Block various types of movies
TV Ratings Block various types of movies
Canadian Ratings (ENG)
Canadian Ratings (FRN)
Alternate Ratings U.S. Ratings system for DTV Signal
and/or Side panel.
and video types based on motion picture ratings.
and television programming based on a parental guide ratings. Block various types of movies and television programming based on the Canadian ratings system. Block various types of movies and television programming based on the Canadian French ratings system.
to block various types of programs
Power Swivel
42
Video
Video
Select VIDEO to adjust picture settings and improve picture quality. You can independently customize each of the Video Inputs to your preference to increase viewing performance and pleasure depending upon the video program being viewed. If RESET is selected, only the selected input will reset to initial conditions.
Picture Mode
Use this function to choose from automatic picture settings to optimize your TV’s performance.
1. Use the CURSOR buttons select PICTURE MODE settings (Day-Normal,
Day-Dynamic or Night).
2. Then press the SELECT button to set the mode and return to the Video menu or press EXIT to quit menu.
3. There are 3 Picture Modes available for the customer Day (Dynamic), Day (Normal) and Night mode. Day (Dynamic) is the original factory preset mode , this
can be changed by adjusting any video setting to your desire conditions. Day ( Normal ) can be used as a second video setting for daytime viewing. Night is set to watch programing during nigthtime.
or to highlight and
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move SEL Select
Video
Picture Mode
OR
OR
White Level
Black Level
Color
Tint
Sharpness
Motion Sharpness
Back Light
Color Temperature
Move
SEL Select
Day(Dynamic)
100%
50%
62%
50%
Off
50%
High
Air
On-Screen Display
OR
Picture Mode Day (Dynamic)
Next/Prev Select
SEL
Return
1. Use the CURSOR PAD
2. Press the SELECT button or the CURSOR PAD
3. Press the CURSOR PAD
or or CHANNEL WHEEL to highlight the function to be adjusted.
to select the function settings.
or to adjust the function.
4. Press MENU to return to main menu.
5. Press EXIT to quit menu.
White Level
Use this function to change the white level in the picture.
Black Level
Use this function to change the black level in the picture.
Color
Use this function to adjust the level of color in the picture.
Tint
Use this function to adjust flesh tones so they appear natural.
Sharpness
Use this function to adjust the amount of fine detail in the picture.
Motion Sharpness
When moving picture occurs detail in the picture is lost this function improves the picture detail in 3 modes Off,
Low and High.
Back Light
Use this function to change the back light of the LCD panel, this will increase or decrease the brightness of the LCD panel, but not the brightness of the video signal.
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move SEL Select
Video
Picture Mode
OR
White Level
Black Level
Color
Tint
Sharpness
Motion Sharpness
Back Light
Color Temperature
Move
SEL Select
Day(Dynamic)
100%
50%
62%
50%
Off
50%
High
Air
43
Video
Color Temperature
Set this to High for cooler color with more blue, set to Medium for more natural color, set to Standard for accurate
color or set to Black/White for more reddish color.
Black Enhancement
Use this function to enhance the shadow detail in dark scenes using the settings off, low, middle and high.
NOTE: 1. If WHITE LEVEL is selected, you are adjusting CONTRAST. The additional menu items BLACK LEVEL,
COLOR, TINT, and SHARPNESS can be selected and adjusted in the same manner.
2. It may be necessary to adjust TINT to obtain optimum picture quality when using the COMPONENT VIDEO Y-P
BPR input jacks.
3. CABLE and AIR share a Video setting. Also, each of the video inputs have their own independent settings.
Contrast Mode
Use this function to choose between 2 Contrast Mode settings. Set to Dynamic for darker images more in the level of Black, set to Normal for a balanced White to Black level.
Noise Reduction
The NOISE REDUCTION function automatically reduces conspicuous noise in the picture without degrading picture quality. Set NOISE REDUCTION to OFF if the TV experiences picture blocking.
Auto Movie Mode
The AUTO MOVIE MODE function turn ON or OFF the 3:2 PULLDOWN DETECTION SPECIAL FEATURE. Theatrical movies are shot on film at 24 frames or still pictures per second, instead of 30 frames or 60 fields like video. When film is transferred to video for television viewing, the disparity between the two frame rates must be reconciled. This involves a process known as 3:2 pulldown.
When AUTO MOVIE MODE is turned ON from the VIDEO menu, your Hitachi LCD Television will activate the circuitry for this special feature to improve video performance when watching film based sources.
NOTE: 1. When using a Progressive Scan Component or HDMI Input (480p or 720p), AUTO MOVIE MODE
will not be available
2. All Video settings are independent of each other based on it’s input (Cable/Air, Input 1~5).
Color Management
Use this function to adjust and balance the listed individual colors to make them either deeper or more pure depending on the user’s preference. Adjust the GAIN settings to make the color brighter (+) or darker (-). Adjust the PHASE settings to make the colors deeper (+) or normal (-) to match real life colors.
1. Use CURSOR PAD or or CHANNEL WHEEL to
2. Press the SELECT button or CURSOR PAD to select Set User Colors setting. When the function has a “” in the box called “Set User Colors”, it is ON.
3. Press the CURSOR PAD , , ,  and SELECT button to highlight and adjust individual colors.
4. Use the CURSOR PAD  and  to highlight and select
“Reset” then press the SELECT button to return all colors to default settings.
NOTE: When the Set User Colors box is not
checked, the listed colors will be grayed out.
On-Screen Display
highlight the Color Management function.
OR
Video
Noise Reduction Low
Auto Movie Mode
Color Management
Color Decoding
Auto Color
White Balance
Black Side Panel O
Aspect
Reset V ideo Settings
Move
or
Video
Color Management
Magenta
Red Yellow
Green
Cyan
Blue
Move
SEL Select
Set User Colors
SEL Return
Phase ±0 ±0 ±0 ±0 ±0 ±0
Reset
Gain ±0 ±0 ±0 ±0 ±0 ±0
O
O
Gain
Phase
44
Video
Color Decoding
Use this function to adjust and balance the percentage of Red, Green and Color according to the user’s preference in each of the four color temperature settings. Use TINT to adjust flesh tones so they appear natural.
1. Use CURSOR PAD
or or CHANNEL WHEEL to
highlight functions.
2. Press the CURSOR PAD , ,  or  and SELECT button to highlight and adjust individual colors.
or
Video
Color Decoding
RGB R G B
Red 50%
50%
Green
62
%
Color
Tint
Reset
SEL Return
Move
NOTE: The Red and Green adjustments will apply for each color temperature.
Auto Color
The Auto Color function automatically monitors and adjusts the color to maintain constant color levels even after a program or channel changes. It also maintains natural flesh tones while preserving fidelity of background colors.
NOTE: When receiving Antenna Digital Channel or using Component input , Auto Color will not be available (grayed out).
White Balance
Use the CUTOFF functions to adjust the color temperature of the dark areas of the picture. Use the DRIVE functions to adjust the color temperature of the bright areas of the picture.
1. Use the CURSOR PAD
or or CHANNEL WHEEL
to highlight the choice.
2. Press the CURSOR PAD  or  to adjust.
3. Press the EXIT button to quit or select White Balance to return to the previous MENU.
or
Video
White Balance
Color Temperature : High
Red Drive
Green Drive Blue Drive
Red Cuto
Green Cuto
Blue Cuto
Reset
Move
SEL Return
100% 100% 100% 50% 50% 50%
On-Screen Display
Black Side Panel
The BLACK SIDE PANEL function turns the gray side bars on/off when watching 4:3 signals in Standard mode or use of the PIP modes.
1. Press the CURSOR PAD  or  to set to ON or OFF.
2. Press EXIT to quit menu or select BLACK SIDE PANEL to return to the previous menu.
Black Side Panel Next On/Off
Black Side Panel Next On/Off
O
SEL Return
On
SEL Return
45
Video
Reset Video Settings
This function allows you to Reset the Video Menu Settings of the present input and return it to the Day-Dynamic VIDEO mode.
1. Use CURSOR PAD , or CHANNEL WHEEL buttons to highlight functions.
2. Press the SELECT button or CURSOR PAD  to select Reset Video Settings.
3. Use the CURSOR PAD to access at the Reset softkey.
4. Press the SELECT button to Reset the Video Settings.
You can customize each of the Video Inputs to your preference to increase viewing performance and pleasure, depending upon the video program being viewed. If RESET is selected, only the selected Input will reset to the initial conditions as explained above.
If RESET is selected in Input 1, only Input 1 will return to factory conditions.
Aspect
Use this function to select the Picture Format Aspect Ratio.
Auto Aspect
Automatically adjust the Aspect Ratio depending on the input signal to fill the screen.
Mode
Manually select the Aspect Ratio.
Vertical Position
This function allows you to select when aspect style is either 4:3 EXPANDED/ZOOM1/ZOOM2 or 16:9 ZOOM. Vertical position can be changed with these modes. For example, it will be useful for centering the picture area at both the top and bottom of the picture with 480i/480p signal. Adjustable range is -10 (video center is toward bottom of screen) to +10 (video is toward top of screen).
Video
OR
Aspect
Auto Aspect : On Mode 16:9 Standard1 Vertical Position : 0
Move
SEL Return
1. Use the CURSOR PAD
2. Press the CURSOR PAD
or to to select menu item.
or to adjust the function.
3. Press the EXIT to quit the MENU, or select ASPECT to return to the main menu.
NOTE: Vertical Position will not be available in 4:3 Standard and 16:9 Standard modes.
OR
Move
On-Screen Display
OR
Video
Noise Reduction Low
Auto Movie Mode
Color Management
Color Decoding
Auto Color
White Balance
Aspect
Black Side Panel
Reset Video Settings
SEL Select
Video
Reset Video Settings
Select “Reset” to return the video menu settings on this Input to the original factory settings.
Reset
O
O
O
46
Move
SEL Return
or
Audio
Audio
Select AUDIO to adjust the TV to your preference and to improve the sound quality.
1. Press CURSOR PAD  or  to select menu item.
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move
SEL
Select
2. Press CURSOR PAD  or  to adjust the function.
3. Press EXIT to quit the MENU, or select AUDIO to return to the main menu.
NOTE: If TREBLE is selected you are adjusting
treble. The additional menu items Bass and Balance can be selected and adjusted in the same manner.
Treble
OR
Audio
Treble
Bass
Balance
Surround
Bass Boost
Audio Source
Internal Speakers
Auto Noise Cancel
Perfect Volume
Move
SEL Return
50%
50%
L R
Off
On
Stereo
On
Off
Off
This function controls the high frequency audio to all speakers.
Bass
This function controls the low frequency audio to all speakers.
Balance
This function will control the left to right balance of the LCD TV internal speakers.
Surround
Surround sound is the concept of expanding the spatial imaging of audio from one dimension ( Mono/Left-Right) to two or three dimensions. This is often done to create a more realistic audio environment.
On-Screen Display
1.- Use cursor to highlight surround option.
2.- Use cursor to select Off, Normal or Wide.
or
Off : turns off the surround sound effect. Normal Surround : Provides the surround effect by locating two or more speakers to the rear of the listener. Wide Surround : Reproduce much better quality 5 channel sound signals from ordinary stereo contents comparing with
normal surround technology. Wide surround enable users to enjoy sound playback in wide surround virtual area like
5 channel contents with ordinary stereo contents.
Bass Boost
This function allows to enhance the low frequency audio performance of your speaker system.
47
Audio Source
Multi-Channel Television Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural sound) used when receiving a weak stereo broadcast or SECOND AUDIO PROG (SAP) which may be a secondary language, weather report, etc.
Internal Speakers
This function is useful when setting up the external speakers.
ON Select this feature if using the internal speakers only. TV as Center Select this feature when setting up external speakers from a separate stereo system. The
TV’s speakers will work as the center speaker.
OFF Select this feature if you prefer to use only speakers from a separate stereo system.
Auto Noise Cancel
This function eliminates the noise between stations. If a channel is tuned and is noisy, this function will automatically eliminate the audio for that channel.
Perfect Volume
This function will automatically adjust volume so each channel and input has the same average volume level.
Loudness
Set this function to ON to emphasize bass and treble at low volume levels.
Language
Some programs transmit more than one DTV language option. Most will have English as a default language. The language function will allow you to select up to 4 language options (if available).
Digital Output
This function allows you to select between Dolby
® Digital and PCM.
Dolby
®
Digital - Select this feature if the TV is connected to an amplifier/receiver with a Dolby®Digital only
decoder; it will provide six independent soundtrack channels through the optical output jack (Digital Audio).
NOTE: *Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
PCM - Select this feature if the TV is connected to an amplifier/receiver with a PCM only decoder; it will provide two independent soundtrack channels through the optical output jack (Digital Audio).
DRC
Dynamic Range Compression - Use this function to compress the range of sound volume. By compressing the range of sound volume, it is possible not only to suppress the output of loud sound at night but also to
raise the volume of low sound. The default setting is ON.
Use the CURSOR PAD  or  to select the chosen options.
NOTE: The functions Language, Digital Output and DRC are only available when viewing digital programs.
Use the functions at right if your TV is connected to an amplifier/receiver with optical digital input with Dolby Digital or PCM decoder capabilities.
NOTE: 1.- The DRC control affects only Dolby Digital
signals decoded internally by the TV.
2.- DRC does not affect the Dolby Digital bitstream available at the digital audio output.
Audio
On-Screen Display
OR
Audio
Treble
Bass
Balance
Surround
Bass Boost
Audio Source
Internal Speakers
Auto Noise Cancel
Perfect Volume
Move
Audio
Bass Boost
Audio Source
Internal Speakers
Auto Noise Cancel
Perfect Volume
Loudness
Language
Digital Output
DRC
Move
SEL Return
SEL Return
50%
50%
L R
Off
On
Stereo
On
Off
Off
On
Stereo
On
Off
Off
Off
1 [Unknown]
Dolby Digital
On
48
TV Guide On Screen
TV Guide On Screen
The TV Guide On-Screen system is a built-in feature that provides a channel lineup and program listings in your area. Once the setup process is complete, the program listings are automatically updated several times a day.
If using a VCR, you must first setup the
LCD TV as shown on Page 22.
To Setup the TV Guide On Screen System:
1. Press the MENU button. Use the CURSOR PAD to highlight TV GUIDE ON SCREEN, then press the SELECT button.
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move SEL Select
Screen 2: Enter the zip code (USA) or postal code (Canada):
Use the Numeric buttons and the CURSOR PAD and for letter entries to enter the ZIP code (USA) or postal code (CANADA) of your location.
*For USA is a 5 digit ZIP CODE
**For CANADA is a 6 digit ZIP CODE
Screen 3:
Please select which service(s) you would like your
TV Guide On Screen
TM
to support (Check all that
apply):
Use the CURSOR PAD  and  to highlight your
choice, then press the SELECT button then select Next :
On-Screen Display
Note: Pressing the GUIDE button also allows you
immediate access to this feature.
2. Press the SELECT button to continue.
Setup Procedure:
Screen 1: Select which country your TV is located in:
Use the CURSOR PAD  and  to highlight your TV location (USA or CANADA), then press the SELECT button to continue.
Screen 4:
Are the above settings correct ?
Use the CURSOR PAD  and  to highlight your
choice, then press the SELECT button then select Next :
*If all setting are correct please select Yes to continue. *If a setting is wrong please select No to modify.
49
Screen 5:
Would you like to use the TV Guide On Screen
Use the CURSOR PAD and to highlight your choice, then press the SELECT button then next. If YES: Please see Screen 6. If NO: Please see Screen 12.
Screen 6:
The screen will show the correct way to setup the VCR with the G-Link. Please confirm the connections (see page 22). Press SELECT
Screen 7:
What brand of VCR is connected to this TV ?
Use the CURSOR PAD  and  to highlight your choice, then press the SELECT button to continue.
Screen 8:
This screen shows the stept that you need to follow to make the correct setup of your VCR with the G-LINK. Please check your connection (see Page 22). Press the SELECT button to continue.
Screen 9:
Now the TV GUIDE will send the code to control the VCR through the G-Link connection.
Screen 10:
Did your VCR stop playback of the TAPE ? If Yes then go to screen 11 If No the TV Guide will try a different code and return to screen 9. If you like to Test this test code again one more time
TV Guide On Screen
system to control recording with your VCR?
button to continue.
On-Screen Display
50
TV Guide On Screen
NOTE: 1. The LCD TV should be in standby mode
in order to continually receive updated program listings from your cable company.
2. If using a Cable box, please leave it ON to continually receive updated program listings from your cable company.
Screen 11:
Are the settings correct ? If Yes the TV Guide setup is complete, then press SELECT button to continue. If No please make the necessary changes in order to complete the TV Guide setup procedure.
Screen 12:
This shows that the setup procedure is complete Use the CURSOR PAD and to highlight Next or if you are like to make changes select Back ; Then press SELECT button to continue or finish.
Screen 14:
None of the Hitachi codes appeared to control your VCR. What would you like to do now ?
1.- Try VCR configuration again to repeat the setup.
2.- Try alternate remote codes to see other code alternatives that may solve the problem.
3.- Skip this step , will finish the TV Guide setup ;
but will show an incomplete setup for your VCR.
Screen 13:
When a CODE for a VCR is not accepted then the following message will appear. Check the setup as mentioned then select Next.
On-Screen Display
For using and navigating the TV Guide On Screen System please refer to the TV Guide Instruction Book.
51
Channel Manager
or
Channel Manager
Select CHANNEL MANAGER to set your Antenna options, run Auto Channel Scan, Check Signal Meter and Set Channel List.
1. Press CURSOR PAD ,  or CHANNEL WHEEL buttons to highlight function.
2. Press the SELECT button or CURSOR PAD  to select.
Signal Meter
Select SIGNAL METER when using an indoor or outdoor antenna. This feature will show the signal strength and peak values of the Antenna signal to help you adjust your antenna to optimize signal reception.
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move
SEL
Select
Channel Manager
OR
OR
Signal Meter
Auto Channel Scan
Channel List
Move
Channel Manager
Signal Meter
Auto Channel Scan
Channel List
Move
SEL Select
SEL Select
On-Screen Display
Use the CURSOR PADS and the SELECT button to highlight and select CLOSE to exit.
NOTE: The Signal Meter will not be available (grayed
out) when watching analog channels.
Auto Channel Scan
This feature will automatically store active Analog and Digital channels in Auto Channel Scan memory.
1. Use the CURSOR buttons to highlight
AIR, CABLE (1) or CABLE(2) source.
2. Press the CURSOR buttons
or to highlight the
START or RESET option.
3. Press the SELECT button to select.
NOTE: 1. When a CableCARD is installed, Auto
Channel Scan will not be available since channels will be fixed based on what was agreed upon by you and your cable operator.
2. If certain channels are poor or not possible in cable(1) mode, set cable source to cable(2) by using the CURSOR buttons  or .
Channel Manager
Signal Meter
Channel 3- 1 Strength 91 Peak 91
SNR 10
Close
Move SEL Return
Channel Manager
Signal Meter
Auto Channel Scan
Channel List
Move
SEL Select
Channe l Man ager
OR
Auto Channel Scan
Source Air
Auto Channel Scan
Move SEL Return
Start Reset
52
Channel Manager
Channel List
This function allows you to review which channels are labeled (CH ID), which have been added to CHANNEL MEMORY (SCAN), which are protected by LOCK and
Channel Manager
Signal Meter
Auto Channel Scan
Channel List
Move
SEL Return
which are your FAVORITE (FAV) CHANNELS.
1. Use the CURSOR PAD to navigate the Channel List.
2. Press the SELECT button to select ON or OFF on the SCAN and LOCK columns.
3. To select LOCK column, input the access code. (Default access code: 0000)
4. Press the CHANNEL WHEEL button to set or remove the FAVORITE channel settings.
5. Press the EXIT button to return to normal viewing.
OR
Channel Manager
Channel List

FAV CH# Scan Lock ID
3-1 OnO -------
4On O ------­5On O ------­6On O ------­7On O ------­8On O ------­9On O -------
10 On O -------
No Info.
Move Return
--:-- AM- --:-- AM
INFO Detail
NOTE: 1. When a CableCARD is installed, the Channel List will be dependent on channels agreed
upon by you and your cable operator.
2. The Channel List cannot be updated by only changing the cable source. Auto Channel Scan must be performed for the Channel List to be updated.
On-Screen Display
53
Locks
Locks
This function will block out the picture and sound of the selected channel or video input.
The code to enter the Locks feature is a four digit access code number. The factory preset code is 0000. Use the NUMBER buttons to enter the access code.
1. Use the CURSOR PAD
WHEEL buttons to highlight the desired function in the LOCKS menu.
2. Press the SELECT button to select.
Change Access Code
1. To change the ACCESS CODE NUMBER, select CHANGE ACCESS CODE to change the factory
preset code (0000) to your preference.
If you forget your ACCESS CODE NUMBER, use the factory code 7777 to erase your key number. This will reset the access code number back to the factory preset (0000).
2. Enter a new four digit number.
,  or CHANNEL
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move
SEL
Select
OR
Please Enter Access Code
Access Code: - - - -
[#Keys] Enter Code
0
0
0
0
Locks
Change Access Code
Engage Lock
Movie Ratings
TV Ratings
Canadian Ratings(Eng)
Canadian Ratings(Frn)
Alternate Ratings U.S.
Move SEL Select
On-Screen Display
3. Press EXIT to quit the menu.
Engage Lock
When ENGAGE LOCK is selected, SET CHANNEL LOCK and SET FRONT PANEL LOCK can be set individually.
When SET CHANNEL LOCK is turned on, the picture and sound for the chosen channel will be blocked out.
When FRONT PANEL LOCK is turned on, all buttons on the Front Panel will be deactivated, except the POWER button.
When MOVIE RATINGS is selected, you can block various types of movies and video tapes based on motion
picture ratings. Picture-in-Picture will also be blocked automatically (see page 55).
When TV RATINGS is selected, various types of television programming based on a parental guide ratings will be
blocked. Picture-in-Picture will also be blocked automatically (see page 56).
Use CANADIAN RATINGS to block various types of movies and television programs based on the two rating
systems used in Canada that you feel may be inappropriate due to its content (see pages 57-58).
Use ALTERNATE RATINGS (U.S.) to block various types of movies and television pograms based on ratings systems used in U.S. that you feel may be inappropriate due to its content (see page 59).
NOTE:
The ALTERNATE RATINGS (U.S.) option is available for Digital Channels only.
54
Locks
Movie Ratings
Use Movie Ratings to prevent viewing of any movie that you feel may be inappropriate due to its content.
1. Use the CURSOR PAD
,  or CHANNEL WHEEL
buttons to select the MOVIE RATING category that you want to block.
Locks
Change Access Code
Engage Lock
Movie Ratings
TV Ratings
Canadian Ratings(Eng)
Canadian Ratings(Frn)
Alternate Ratings U.S.
Move SEL Select
2. Press SELECT to block the MOVIE RATING that you have selected. Once rating is selected, for example PG-13, all movies rated PG-13 and higher (R, NC-17, and X) will be blocked.
OR
3. Press EXIT to quit the menu or select MOVIE RATING to return to the previous menu.
Locks
Movie Ratings
sutatS
detaRtoN G PG PG-13 R NC-17 X
Move SEL Return
Motion Picture Ratings Table
NOT RATED Contains no rating. Not Rated (NR) and Not Applicable (NA) programs. Movie has not
been rated or ratings do not apply. G General audiences. All ages admitted. PG Parental guidance suggested. Some material may not be suitable for children. PG-13 Parents strongly cautioned. Some material may be inappropriate for children under 13. R Restricted. Under 17 requires accompanying parent or adult guardian. NC-17 No one 17 and under admitted. X Adults only
On-Screen Display
NOTE: 1. A movie rating is dependent upon the movie that is viewed. If the movie does not carry a rating, the
TV will not block it.
2. Blocking NOT RATED programs may block emergency programming, sports, news, public service announcements, religious programs and weather.
3. If a CableCARD is installed, your cable operator may provide an Emergency Alert System (EAS) message in the event of a local or national emergency with the purpose of alerting the general public. When you receive such messages, the Television will immediately tune to an EAS channel as directed by the EAS message. Please be advised that if the EAS channel is blocked using the LOCKS feature, you will not be able to tune to that channel.
55
Locks
On-Screen Display
TV Ratings
Use TV RATINGS to prevent the viewing of any TV program that you feel may be inappropriate due to its content.
1. Use the CURSOR PAD
,  or CHANNEL WHEEL
buttons to select the TV RATING category that you
want to block.
Locks
Change Access Code
Engage Lock
Movie Ratings
TV Ratings
Canadian Ratings(Eng)
Canadian Ratings(Frn)
Alternate Ratings U.S.
Move SEL Select
2. Press SELECT to block the TV RATING that you have selected.
3. Press EXIT to quit the menu or select TV RATING
to return to the previous menu.
OR
Locks
TV Ratings
Status D L S V FV
Y-VT TV-Y7 TV-G TV-PG TV-14 TV-MA
Move SEL Return
gnitaRbuS
TV Parental Guide Ratings Table
TV-Y All children. The themes and elements in this program are specifically designed for a very
young audience, including children from ages 2-6.
TV-Y7 Directed to older children. Themes and elements in this program may include mild
physical or comedic violence, or may frighten children under the age of 7.
TV-G General audience. It contains little or no violence, no strong language, and little or no
sexual dialogue or situations.
TV-PG Parental guidance suggested. The program may contain infrequent coarse language,
limited violence, some suggestive sexual dialogue and situations.
TV-14 Parents strongly cautioned. This program may contain sophisticated themes, intense
sexual situation, more intense violence and intensely suggestive dialogue.
TV-MA Mature audiences only. This program may contain mature themes, indecent language,
graphic violence, and explicit sexual content. FV Fantasy Violence V Violence S Sexual Situation L Adult Language D Sexually Suggestive Dialogue
NOTE: 1. If you Block TV-14D, you will still permit TV-MA programs; If you block TV-14V, you will
automatically block TV-MAV programs, but you will still permit TV-MALS programs. This means that the TV will block violence in TV-14 and higher (TV-MA), but not language and sex.
2. TV program ratings are dependent on the broadcaster. If the program is not rated, the TV will not block it.
3. If a CableCARD is installed, your cable operator may provide an Emergency Alert System (EAS) message in the event of a local or national emergency with the purpose of alerting the general public. When you receive such messages, the Television will immediately tune to an EAS channel as directed by the EAS message. Please be advised that if the EAS channel is blocked using the LOCKS feature, you will not be able to tune to that channel.
56
Locks
Canadian Ratings (Eng)
Use CANADIAN RATINGS (ENG) to block any type of movie and television program in Canada that you feel might be inappropriate in its content.
1. Use the CURSOR PAD
,  or CHANNEL WHEEL
buttons to select the CANADIAN RATINGS
(ENG) category that you want to block.
Locks
Change Access Code
Engage Lock
Movie Ratings
TV Ratings
Canadian Ratings(Eng)
Canadian Ratings(Frn)
Alternate Ratings U.S.
Move SEL Select
2. Press SELECT to block the CANADIAN RATINGS (ENG) that you have selected. Once rating is
selected, for example C8+, all movies and television programs rated C8+ and higher (G, PG, 14+ and 18+) will be blocked automatically.
3. Press EXIT to quit the menu or select CANADIAN RATINGS (ENG) to return to the previous menu.
OR
Locks
Canadian Ratings(Eng)
sutatS
C C8+ G PG 14+ 18+
Move SEL Return
Canadian Ratings English Table
C Programming intended for children under age 8 - Violence Guidelines; Careful attention is
paid to themes, which could threaten children’s sense of security and well-being. There will be no realistic scenes of violence. Depictions of aggressive behaviour will be infrequent and limited to portrayals that are clearly imaginary, comedic or unrealistic in nature. Other Content Guidelines: There will be no offensive language, nudity or sexual content.
C8+ Programming generally considered acceptable for children 8 years and over to watch on
their own - Violence Guidelines: Violence will not be portrayed as the preferred, acceptable, or only way to resolve conflict; or encourage children to imitate dangerous acts which they may see on television. Any realistic depictions of violence will be infrequent, discreet, of low intensity and will show the consequences of the acts. Other Content Guidelines: There will be no profanity, nudity or sexual content.
G General Audience - Violence Guidelines: Will contain very little violence, either physical or
verbal or emotional. Will be sensitive to themes which could frighten a younger child, will not depict realistic scenes of violence which minimize or gloss over the effects of violent acts. Other Content Guidelines: There may be some inoffensive slang, no profanity and no nudity.
PG Parental Guidance - Programming intended for a general audience but which may not be
suitable for younger children. Parents may consider some content inappropriate for unsupervised viewing by children ages 8-13. Violence Guidelines: Depictions of conflict and/or aggression will be limited and moderate; may include physical, fantasy, or supernatural violence. Other Content Guidelines: May contain infrequent mild profanity, or mildly suggestive language. Could also contain brief scenes of nudity.
14+ Programming contains themes or content which may not be suitable for viewers under the
age of 14 - Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and early teens. Violence Guidelines: May contain intense scenes of violence. Could deal with mature themes and societal issues in a realistic fashion. Other Content Guidelines: May contain scenes of nudity and/or sexual activity. There could be frequent use of profanity.
18+ Adult - Violence Guidelines: May contain violence integral to the development of the plot,
character or theme, intended for adult audiences. Other Content Guidelines: May contain graphic language and explicit portrayals of nudity and/or sex.
On-Screen Display
57
Locks
Canadian Ratings (Frn)
Use CANADIAN RATINGS (FRN) to block Canadian French programs according to various program ratings that you feel might be inappropriate in its content.
1. Use the CURSOR PAD
, or CHANNEL WHEEL
buttons to select the CANADIAN RATINGS
(FRN) category that you want to block.
Locks
Change Access Code
Engage Lock
Movie Ratings
TV Ratings
Canadian Ratings(Eng)
Canadian Ratings(Frn)
Alternate Ratings U.S.
Move SEL Select
2. Press SELECT to block the CANADIAN RATINGS (FRN) that you have selected. Once rating is
selected, for example 8 ANS+, all movies and television programs rated 8 ANS+ and higher will be blocked automatically.
3. Press EXIT to quit the menu or select CANADIAN RATINGS (FRN) to return to the previous menu.
OR
Locks
Canadian Ratings(Frn)
sutatS
G 8 ans + 13 ans + 16 ans + 18 ans +
Move SEL Return
Canadian Ratings French Chart
G General - Programming intended for audiences of all ages. Contains no violence, or the
violence content is minimal or is depicted appropriately with humor or caricature or in an unrealistic manner.
8 ans + 8 + General - Not recommended for young children - Programming intended for a broad
audience but contains light or occasional violence that could disturb young children. Viewing with an adult is therefore recommended for young children (under the age of 8) who cannot differentiate between real and imaginary portrayals.
13 ans + Programming may not be suitable for children under the age of 13 - Contains either a few
violent scenes or one or more sufficiently violent scenes to affect them. Viewing with an adult is therefore strongly recommended for children under 13.
16 ans + Programming is not suitable for children under the age of 16 - Contains frequent scenes of
violence or intense violence.
18 ans + Programming restricted to adults - Contains constant violence or scenes of extreme
violence.
On-Screen Display
58
Locks
T
TV-Y7
ABCDEFJH
T
TV-Y7
ABCDEFJH
Alternate Ratings U.S.
Use Alternate Ratings to prevent viewing of any movie or program that you feel may be inappropriate due to its content.
This feature will be available only for ATSC Digital signal. In case only NTSC analog signal is received this feature will
be unavailable (grayed out).
In order to set the Alternate Ratings the ATSC Digital channel received must include Alternate Ratings data .To see if the channel has Alternate Ratings , press the INFO key on the R/C. See fig. (1) for reference.
Once the TV has received Alternate Ratings data , the Alternate Ratings US in the lock menu will become available.
1.
Use the CURSOR buttons or to select the
ALTERNATE RATIN G category that you want to block.
INFO
Receiving
Audio Language
(Digital CH)
/Receiving BTSC
(Analo g CH )
Receiving
Rating Broadcast
Alternate Ratings
Closed Caption Mode
OR
Program Title
Program Title. . . . . . . . Cable 888-001
11:30AM
11:55AM ALT U.S. KDEF-DT
Multi DTVCC CF-18 ans+ 1080i 10:35 AM
Fig. (1)
Locks
Change Access Code
Engage Lock
Movie Ratings
TV Ratings
Canadian Ratings(Eng)
Canadian Ratings(Frn)
Alternate Ratings U.S.
Move SEL Select
Locks
Alternate Ratings U.S.
Status CATEGORY NAME (1 / 10)
V-Y
:
: :
12345678
:[ ]
Program Time
Receiving Digital Closed Caption
MA03:11otuA
Event Timer G-Guide Model
Source
CH ID/Input ID
Current Time
Receiving Signal Format
On-Screen Display
Press SELECT to block the ALTERNATE RATING
2.
Move SEL View Block
that you have selected. Once rating is selected, for
example PG-13, all movies rated PG-13 and higher (R, NC-17 and X) will be blocked.
Press EXIT to quit the menu or select ALTERNATE
3.
RATINGS to return to the previous me nu.
OR
Locks
Alternate Ratings U.S.
Status CATEGORY NAME (1 / 10)
V-Y
:
: :
12345678
:[ ]
Directed to older children. Themes and elements in this program may include mild physical or comedic violence, or may frighten children under the age of 7.
Move SEL View Block
Alternate Ratings (Example Only) :
G General audiences. All ages admitted. PG Parental guidance suggested. Some material may not be suitable for children. PG-13 Parents strongly cautioned. Some material may be inappropriate for children under 13. R Restricted. Under 17 requires accompanying parent or adult guardian. NC-17 No one 17 and under admitted. X Adults only
Y Adults only
NOTE: In some cases the OSD will show the function name as " Alternate Ratings U.S. " or "Downloaded
Ratings " , in both cases the operation is the same only name is different.
59
Timers
NOTE: 1. When AUTOMATICALLY ADJUST CLOCK FOR DAYLIGHT SAVING CHANGES is checked
, the
TV will automatically calculate the clock adjustment for Daylight Saving.
2. When the CableCARD is used, the TV will SET THE CLOCK automatically and also when the TV Guide
3. The TV counts electrical pulses for regulating the TIMERS. When the power cord is unplugged then plugged in quickly, the clock is stopped momentarily and the TIME indication will become slow.
Timers
Select TIMERS to set your Clock, Sleep Timer and Day/Night Timer.
1. Use the CURSOR buttons
WHEEL to highlight the function to be adjusted.
2. Press the SELECT button to select.
Set The Clock
The Clock must be adjusted before you can use the
DAY/NIGHT TIMER feature.
1. Use the CURSOR PAD
WHEEL buttons to highlight the chosen TIME ZONE settings.
or or CHANNEL
, , ,  or CHANNEL
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Mov e
SEL
Select
Timers
OR
Set The Clock
Set Sleep Timer
Set Day/Night Timer
Move SEL Return
Timers
Set The Clock
Set Sleep Timer
Set Day/Night Timer
Move SEL Select
-- : -- AM PST
0:00
Not Set
-- : -- AM PST
0:00
Not Set
2. Press the SELECT button to select. If you observe daylight savings, use CURSOR PAD to highlight
DAYLIGHT SAVING CORRECTION and press the SELECT button to select.
3. Use the CURSOR PAD
, , , or CHANNEL
OR
Timers
WHEEL buttonsto highlight the CURRENT TIME hour and minute), AM or PM, MONTH, DAY, and YEAR.
On-Screen Display
4. Use the CURSOR PAD
,  to adjust settings.
5. Press the SELECT button to set the TIME AND DATE.
6. Press EXIT to quit the menu or select SET THE CLOCK to return to the previous menu.
On Screen system setup process is complete. In this case the Set The Clock feature will not be available (grayed out).
Set The Clock
Time Zone : PST Date : Jan. 1 2005 Time : -- : -- AM
Automatically adjust clock
for daylight savings changes.
Move SEL Return
60
Timers
Set Sleep Timer
Select this feature to set your SLEEP TIMER from 30 minutes to 3 hours (30 minute increments).
1. Press the CURSOR PAD
repeatedly to set your
Timer from 0:00, 0:30, 1:00, 1:30, 2:00, 2:30 and 3:00.
Set Day/Night Timer
Select this feature to activate and set your TV’s DAY/NIGHT PICTURE MODE automatically. This feature is not available until the clock is set.
1. Use the CURSOR PADS to highlight SET DAY/NIGHT TIMER settings.
2. Press the SELECT button to select.
Timers
Set The Clock
Set Sleep Timer
Set Day/Night Timer
Move SEL Select
Timers
Set The Clock
Set Sleep Timer
Set Day/Night Timer
Move SEL Set
Timers
Set The Clock
Set Sleep Timer
Set Day/Night Timer
Move SEL Select
-- : -- AM PST
0:00
Not Set
-- : -- AM PST
0:00
Not Set
-- : -- PST
0:00
Not Set
On-Screen Display
3. Use the CURSOR PADS to select DAY MODE ON and to set it’s TIMER.
4. Use the CURSOR PADS to select DAY MODE OFF and to set it’s TIMER.
5. Press EXIT to quit the menu or select SET DAY/NIGHT TIMER to return to the previous menu.
Timers
OR
Set Day/Night Timer
Activate Day Mode On : 06:00 AM Day Mode O : 06:00 PM
Move SEL Return
61
Setup
Setup
Select SETUP when setting your TV up for the first time.
1. Use the CURSOR PAD sub-menu of your choice.
2. Press the SELECT button to select.
Set The Menu Options
Setup the Language and background of the Menu OSD.
Set The Language
This feature will allow you to select any one of three different languages for all on-screen displays.
, ,  or  to select the
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move
SEL
Select
Setup
OR
Set The Menu Options
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move SEL Select
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move
SEL
Select
On-Screen Display
1. Use the CURSOR PAD
or to select the
language of your choice.
2. Press EXIT to quit menu or select SET THE MENU OPTIONS to return to previous menu.
Setup
OR
OR
Set The Menu Options
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move SEL Select
Setup
Set The Menu Options
Set The Language : English Set The Menu Background : Shaded
Move SEL Return
62
Setup
Set the Menu Background
This function allows you to choose from two menu
backgrounds.
1. Use the CURSOR PAD
or to highlight
SET THE MENU BACKGROUND (SHADED OR SOLID) of your choice. Use the CURSOR
PAD  or  to select shaded or solid.
2. Select SOLID for a black background (no picture can be seen behind menu screen), select SHADED and a light background is visible.
3. Press EXIT to quit menu or select MENU PREFERENCE to return to previous menu.
Setup
Menu Preference
Set The Language : English Set The Menu Background : Shaded
Move SEL Return
Set The Power Saving
This features help to increase the Lamp life.
Image Power
Use this feature to have the TV save energy by changing the back light level in three modes: Max,Med and Min.
1. Press the CURSOR buttons
or to select the
modes Max, Med or Min.
Automatic Power Saving
Use this feature to have the TV turned OFF automatically when a video signal is not detected for
about 12 seconds.
1. Press the CURSOR buttons
or to highlight
Yes or No.
OR
Setup
Set The Menu Options
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
CableCARD Information
Set The Quick Start Options
Reset The Software
Move SEL Select
Setup
Set The Power Saving
Image Power : Max
Automatic Power Saving
Yes No
Move SEL Return
On-Screen Display
NOTE: Your new HDTV has a built-in Automatic Power Saving feature that shuts Off the TV if a video signal is not
detected within 12 seconds. The default setting for this feature is ON (Yes). The Automatic Power Saving feature needs to be set to OFF (No) before any CableCARD set up can be performed. INSTRUCTIONS:
1. Access the Menu OSD by press the MENU button of the remote control.
2. Navigate the menu to access SETUP, then SET THE POWER SAVING. SET AUTO POWER SAVING OFF (No) using the Cursor and the SELECT buttons of the remote control.
3. Use the Cursor buttons to highlight “No” then press the SELECT button to set this feature to Off.
4. After CableCARD set up is completed, set the Auto Power Saving feature to ON (Yes).
63
Setup
Set The Inputs
Use this feature to give a name to any of the five video inputs.
1. Press the CURSOR PAD
or to highlight the
video inputs.
2. Press the CURSOR PAD
or to select your
choices.
OR
Setup
Set The Menu Options
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move SEL Select
Note: The inputs labeled Gray out (Skip) or Hide
(Skip) are disabled in the INPUTS selection.
INPUT 4 Auto Link
Use this function to automatically turn the TV on and tune to INPUT 4 when it detects a video signal to INPUT 4.
1. Use the CURSOR PAD
, ,  or  to
highlight and select the AUTO LINK setting of
Setup
Set The Inputs
Input1 : Input2 : Input3 : Input4 : Auto Link : O Input5 :
Move SEL Return
your choice.
- Auto
When AUTO is selected, the TV will turn on and switch to INPUT 4 automatically, when the INPUT 4 input device is turned on. This is convenient when you want to watch a movie with your VCR, laserdisc player or DVD player.
- Remote
When REMOTE is selected, the TV will turn on and switch to INPUT 4 automatically when the INPUT 4 input device is turned on and the VCR, laserdisc, or DVD play button on your remote control is pressed. This is convenient when you want to record a movie with your VCR and watch it later.
- Off
Select OFF to disable this function.
2. Press EXIT to quit menu or select SET THE INPUTS to return to previous menu.
**** **** **** ****
****
On-Screen Display
NOTE: 1. Once the TV has been turned on using the AUTO LINK feature, it must be reset before AUTO LINK
is used again. To do this, turn your VCR, laserdisc, or DVD player OFF. This feature is now reset and will turn on your TV as described above.
2. When using REMOTE mode, any remote control button will substitute for your video input device play button. However, intended operation is for use with your VCR, laserdisc, or DVD play button.
3. If no remote control button is pressed after the TV is turned on by AUTO LINK, the TV will automatically turn off after three hours.
Set AV NET
64
Setup
Set The Closed Captions
Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video which are displayed on the TV screen. Your local TV program guide denotes these programs as or .
1. Use the CURSOR PAD
, ,  and  to highlight
and select the function to change.
2. Press EXIT to quit menu or select SET THE CLOSED CAPTIONS to return to the previous menu.
Caption Display:
ON/OFF will turn the display on or off. AUTO will turn the display on when
Mute/Soft Mute is on.
Analog Captions:
Set CAPTIONS for Analog programs. This function will help choose and set available mode and channel.
Caption Mode:
CAPTIONS is for the program you are viewing. TEXT is for additional information such as news reports or a TV program guide. This information covers
the entire screen and viewing the TV program is not possible. Text may not be available with every program.
Channel:
1 is used for the primary language (usually English). 2 is sometimes used for a second language (may vary by region). 3 is sometimes used for a third language (may vary by region). 4 is sometimes used for a fourth language (may vary by region).
Setup
OR
OR
Set The Menu Options
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move SEL Select
Setup
Set The Closed Captions
Caption Display : O
Analog Mode : Captions Channel : 1
Digital Language : 1(Unknown) Font : Default
H i t a c h i Size : Standard
Style : Standard
Move SEL Return
:
On-Screen Display
Digital Captions
Set captions for digital programs. This function will help choose and set available language, font, size and style of digital captions.
1. Use the CURSOR PAD
, ,  or  to highlight
and select desired DIGITAL CAPTIONS feature.
2. Press EXIT to quit menu or select SET CLOSED
Setup
Set The Closed Captions
Caption Display : O
Analog Mode : Captions Channel : 1
Digital Language : 1(Unknown) Font : Default
H i t a c h i Size : Standard
Style : Standard
Move SEL Return
CAPTION to return to the previous menu.
NOTE: 1. Some types of digital closed captions will not work with this TV.
2. Caption Display will not work when viewing a 480p, 720p, or 1080i input via the
COMPONENT: Y- P
BPR inputs.
3.4.Digital Captions Font Style are sometimes different from the Font Style of Analog Captions. Closed Caption and Digital Captions availability and content depends on the broadcaster. Closed Caption is available when Closed Caption icon is displayed on screen.
65
Setup
Set The Output Terminals
This feature will select the source of the Output Terminal.
Video Out :
Select MONITOR to output the audio and video signals of the chosen input source (CABLE, AIR or INPUT 1-5) to a VCR or
other A/V device.
Select TV TUNER OUT to output the audio and video signals of the last watched Antenna Source (CABLE, AIR).
Audio Out:
Select AUDIO OUT FIXED to have the Audio at fixed volume.
Select AUDIO OUT VARIABLE to have Audio
volume that can be controlled by the LCD TV
TV TUNER OUT: Available Monitor Out Signals
3. Press EXIT to quit menu or select SET THE OUTPUT TERMINALS to return to previous menu.
NOTE: 1. When TV TUNER OUT is selected, VARIABLE AUDIO OUT will not be available (grayed out).
2. When using MONITOR OUT for recording, set the VIDEO OUT to MONITOR.
IR Out :
Select IR OUT NORMAL LENGTH to pass remote control signal to IR Out Terminal as is and reach 2m (max)
Select IR OUT EXTENDED LENGTH to process remote control signal to IR Out Terminal and reach 5m (max)
2. Use the CURSOR PAD
or to select the function.
1. Use CURSOR PAD
or or CHANNEL WHEEL to highlight the function to change.
through provided IR Blaster CABLE.
through provided IR Blaster CABLE.
use Normal Length funtion, or point the remote control directly at the external components.
Volume Up/Down.
Video Out Audio Out Use Monitor Fixed To record currently viewed Video and Audio. Monitor Variable When an external device like a monitor
audio and video output of the TV. You can
TV Tuner Out Fixed To record currently viewed Video and Audio from either Cable or Air.
or Hi-Fi audio system is connected to the
control the volume output by changing the volume of the TV.
Setup
OR
OR
Set The Menu Options
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move SEL Select
Setup
Set The Output Terminals
Video Out : Monitor
io Out :
Aud Fixed
IR Out : Normal Length
Move SEL Return
NOTE : Extended Length funtion is not available for some kinds of external components. For those components
On-Screen Display
MONITOR: Available Monitor Out Signals
tuOrotinoMedoMtupnI
iFiHR/LoediVoediV-S
ANT Digital No Macrovision S-Video YES YES YES YES (Air or Channel Macrovision S-Video - - - YES Cable) Analog Channel Video - YES YES YES
ANT Digital No Macrovision S-Video YES YES YES YES (Air or Channel ANT ANT ANT ANT Cable) Macrovision S-Video - - - YES
Input 1 HDMI_1 - - - YES
S-Video_1 YES YES YES YES
Input 2 HDMI_2 - - - YES
Video_1 - YES YES YES
Input 1 HDMI_1 Y-PbPr YES YES YES YES
S-Video_2 YES YES YES YES
Input 3 Y-PbPr_3 - - - YES
Video_2 - YES YES YES
Input4
V
ideo_3
Y-PbPr_4
-
YES YES YES
-
- - YES
Video_4 - YES YES YES
Input 5 HDMI_5 - - - YES
Y-PbPr_5 - - - YES
Video_5 - YES YES YES
Input 2 HDMI_2 Y-PbPr only
Input 3 Y-PbPr_3
Input4 Y-PbPr_4
Input 5 HDMI_5 Y-PbPr
66
Input Mode Monitor Out (TV Tuner Out)
iFiHR/LoediVoediV-S
ANT
Analog Channel Video - YES YES YES
ANT ANT ANT
S-Video_1 ANT ANT ANT ANT
Video_1 digital
S-Video_2
Video_2
Video_3
Video_4
Y- PbPr_5
Video_5
Setup
CableCARD Information
After the CableCARD has been successfully installed,
you can access CableCARD Information menu in the SETUP menu of the On-Screen Display.
Follow the instructions below to access the CableCARD Information menu.
1. Press the MENU button on the Remote Control to access the Main Menu screen.
2. Use the CURSOR PAD
to highlight SETUP in
the Main Menu and press the SELECT button.
3. Use the CURSOR PAD
to highlight CableCARD
Information and press the SELECT button.
4. To view the CableCARD ID and Host ID, use the
CURSOR PAD
to highlight CableCARD Info and
press the SELECT button.
NOTE: The Diagnostics Info. window is for
Service use only.
THINGS TO CHECK WHEN USING THE CableCARD / CableCARD Services
1. Check that the CableCARD is properly inserted in the CableCARD slot.
2. Remove the CableCARD by pulling
the CableCARD straight out.
3. Visually inspect the CableCARD to ensure all pin­holes are in good condition, with none blocked or damaged.
4. Make sure the CableCARD is re-inserted in the correct direction, then slowly push until it is fully seated in the slot.
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move
SEL
Select
Setup
OR
OR
Set The Menu Options
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
CableCARD Information
Set The Quick Start Options
Reset The Software
Move SEL Select
Setup
CableCARD Information
Select the button below to acess CableCARD ID and Host ID.
Select the button below to access CableCARD and Host Diagnostics.
Move SEL Return
CableCARD Info.
Diagnostics Info.
On-Screen Display
In order to start cable service
for this device, please contact
your cable provider
CableCARD(tm): 123-456-789-1 Host: 123-456-789-1 Data: 123-456-789-1
Unit Address: 123-456-789-1
5. When the CableCARD is installed, note all screen messages that appear (“CableCARD Installed”, “Acquiring Data”, “CableCARD is not Installed”). If the “CableCARD Installed” message does not appear when card is installed, check the TV’s card slot and CableCARD pins for obstructions or damage.
6. If problems still remain, please contact your Cable Service Provider.
NOTES:
1. When a CableCARD is installed, Auto Channel scan will not be needed because the channel list is automatically loaded to the TV's channel memory.
2. The TV will take several minutes to detect and recognize the presence of the CableCARD. This process must be completed before any CableCARD information or Channel listings is accessed.
Press EXIT to return
67
Setup
When setting the Quick Start option to ON
the option of Reset TV Settings will not operate.
Set The Quick Start Options
This feature will select QUICK START UP options. Set this feature to ON to have the TV tune channels (both Analog and Digital) quickly when first turning the TV on. Set this feature to OFF to save electricity. Selecting ON for the QUICK START UP feature will activate the TV tuners circuits when the TV is in “standby mode” which is commonly referred to as “off”. This will allow you to quickly tune to channels when first turning the TV on. Digital signals often change and this feature will monitor any changes and prepare the television to quickly present a picture. A small amount of electricity is used to continually monitor signals when this feature is selected.
NOTE:
Setup
OR
OR
Set The Menu Options
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move SEL Select
Setup
Set The Quick Start Options
Select ON to have the TV tune channels quickly at 1st turn on.
Select OFF to save electricity
O On
Move SEL Select
On-Screen Display
Reset The Software
This feature shows software information and easy upgrade procedure. This function allows the TV software to be upgraded by using a flash card (MMC CARD). If a future software upgrade is required for your TV, HITACHI will notify and provide you with a flash card. In order to receive written notification and the flash card, please complete and return the warranty card.
1. Insert MMC CARD
2. Press the CURSOR PAD
or to highlight
UPGRADE NOW.
3. Press the SELECT button to select and start upgrading.
4. Unplug the AC power cord when the UPGRADE is complete.
NOTE: Any power interruption during the upgrade
process will cancel the upgrade. When this happens, repeat the upgrade procedure.
68
Setup
OR
OR
Set The Menu Options
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move SEL Select
Setup
Reset The Software
MMC Software Upgrade:
Upgrade Now
Please Insert MMC card before upgrading.
Reset TV Settings (Select "Yes" to return all settings to the factory default after main power OFF/ON.
Move
No Yes
SEL Return
Main Vxxxx.xxxx
)
Setup
Reset TV Settings
This function allows you to Reset all TV Settings to the original factory settings on all modes during the next
main power on/off.
1. Use CURSOR PAD ,  to highlight functions.
2. Press the SELECT button or CURSOR PAD  to select Reset The Software.
3. Use the CURSOR PAD to access the Reset TV Settings
Setup
Reset The Software
MMC Software Upgrade:
Upgrade Now
Please Insert MMC card before upgrading.
Reset TV Settings : Select "Yes" to return all settings to the factory to the factory default after main power OFF/ON.
Move
No Yes
SEL Return
Main Vxxxx.xxxx
option.
4. Select the "YES" option to Reset ALL the TV Settings during the
next main power on/off.
NOTE: If YES is selected, ALL TV MENU SETTINGS will be reset to the original factory settings on all
modes during the next power on/off.
Power Swivel
This feature controls the motorized stand. It allows
the customer to turn the display left or right using the remote control. This feature is only available
when the Table Top Stand is connected.
1. Use the CURSOR PAD
or to unlock or lock
the Power Swivel.
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move
SEL
Select
Exit the OSD menu system before controlling the motorized stand.
2. Press the CURSOR PAD the right.
to rotate the TV to
or
On-Screen Display
3. Press the CURSOR PAD
to rotate the TV to
the left.
4. Release the CURSOR PAD to stop rotation.
Power Swivel
Select
NOTE: 1. The Power Swivel has a maximum turning radius of 30° (left and right).
2. Do not place any objects in the path of the monitor when using the power swivel feature.
3. Before using the power swivel, please make sure that the path of the monitor is clear of any fingers, hands or any other body parts to avoid causing injury.
4. When the Picture-In-Picture (PIP) or Freeze mode is ON, the Power Swivel is disabled.
Return
Locked
SEL
69
Equipment Care and Troubleshooting
DO
Dust the screen and cabinet with a soft cloth.
Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty.
Place your LCD Television away from extreme heat, humidity, and extremely dusty places.
Remove the plug from the wall outlet if your LCD
Television will not be used for a long period of time, for instance, when you go on vacation.
DO NOT
Do not clean your screen with strong cleaners, polishes or a chemically treated cloth.
Do not place rubber or vinyl products or cellophane
tape on your LCD Television.
Avoid repeatedly touching the screen.
Do not subject the remote control to shocks such as dropping it on the floor, etc. This may cause damage to the precision parts.
Avoid placing the remote control in a high humidity place or getting it wet. Do not leave it on or near a heater. Excessive heat or moisture may cause the unit to fail.
When the batteries run down, remote control operation will become erratic or become unresponsive. Replace the old batteries with two new “AA” size batteries. Do not use an old battery with a new battery.
Exposing the screen to direct sunlight for a long period
of time or heat may cause damage to the LCD
screen.
TROUBLESHOOTING
Your HITACHI LCD Television incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage power surges.
IF YOUR TELEVISION SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE:
1. Press the POWER
2. If there is still no power,
3. If there is still no power,
Useful Information
This protective technology should provide for years of lasting entertainment from your HITACHI LCD Television.
SWITCH (ON/OFF SWITCH) once.
wait 30 seconds and press the POWER SWITCH again.
unplug the power cord from the wall. Wait 30 seconds and plug the power cord back in. Press the POWER SWITCH again.
SYMPTOMS
No Picture, no sound
Sound OK, picture poor
Picture OK, sound poor
Picture blurred
Lines or streaks in picture
Poor reception on some channels
Picture rolls vertically
No color
Poor color
n is corre
Be sure external connectio
Be sure
쏹쏹
power cord is plugged in
Be sure TV is switched''ON"
CHECK THESE ITEMS AND
TRY THESE ADJUSTMENTS
ct
ections (back of TV)
a for broken lead-in
k outside
Chec
Try another channel (station trouble)
쏹쏹쏹쏹
쏹쏹
쏹쏹쏹쏹
쏹쏹쏹쏹
쏹쏹쏹쏹
쏹쏹쏹쏹
쏹쏹쏹쏹
쏹쏹쏹쏹
Chec
Check antenn
Check antenna conn
쏹쏹쏹쏹
쏹쏹
wire
rence
antenna
cal interfe
k for lo
Adjust Contrast control
ess control
Adjust Brightn
Adjust Color control
Adjust Tint control
Adjust Volume control
70
Reception Problems
IGNITION NOISE:
Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances.
GHOSTS:
Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception. Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers.
SNOW:
If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture.
RADIO FREQUENCY INTERFERENCE:
• RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture.
• PREVENTION OF AN OBSTACLE TO RADIO RECEIVERS This television has been designed pursuant to the FCC class B Rules. This is to prevent a problem to Radio receivers. If this television causes a problem to Radio receivers, then take the following steps:
- Keep the television away from Radio.
- Adjust Radio antennas in order for the television not to receive interference.
- The antenna cable of Radio should be kept away from the television.
- Use a coaxial cable for antenna. You can check if this television influences Radio receivers by turning off all other equipment other than the television. If you find a problem receiving Radio when using the television, check the instructions mentioned above.
BLOCK NOISE (DIGITAL INPUT):
Fuzzy blocks may appear in some area or the whole area of the screen. This is usually caused by interference from automobile ignition systems, neon lamps, electrical drills, ghosting of the image and weak signals.
BLACK SCREEN:
When using an antenna, weak signals will display a black screen. It may be necessary to upgrade your antenna.
Useful Information
NOTE: The TV set can generate sound distortion in external devices such as a radio. Please separate radio
equipment from the TV set to a considerable distance.
71
Troubleshooting
1. LCD Television Troubleshooting
IMPORTANT NOTES
No. Items Notes
1 Arching sound from LCD
display monitor’s panel.
2 Interference for infrared
equipment.
3 Picture Image (Spectrum)
4 LCD Surface 5 Transportation
6 Granular spots
Black dots and
7
Bright Points
8
Disturbance to video apparatus
9 Lip Sync
10 Caution on prolonged
storage
11 Operating
12 Storage 13 Power ON or OFF
2. TV Guide On-Screen
My Guide listings disappeared after a power failure.
You should begin to receive listings again within 24 hours.
A buzzing sound might be heard when the LCD display monitor is turned on in a very quiet room. This is due to the LCD panel
drive circuit when it is functioning. This arching sound is normal and it is not a malfunction.
Some infrared rays are emitted from the LCD display monitor’s panel that might affect other infrared controlling equipment.
When receving still picture signals, (e.g. channel number indication or clock indication) for a while, you can see image-like when the picture varied. This is not a defect.
The LCD panel is made from glass. Heavy shock on the front panel might damage it.
When the LCD monitor is transported horizontally, the glass panel has the possibility of being broken or increasing the picture defects. At the time of transportation, horizontal style is prohibited. More-over, please treat the LCD panel with great care because of a precision apparatus. Please instruct transporters so that it should be put into the packing box at the time
of shipment.(There is a possibility that breakage of the panel or defects will increase.) Rough transportation might cause
damage to the panel and pixel failure. When a screen is seen at point-blank range, a random fine grain may be visible to a dark part.
Black dots and Bright points may appear on the LCD screen. This is a structural property of the LCD panel and is not a defect.
If an apparatus (VCR, etc.) antenna line is arranged near the monitor, the image may shake, or disturbance may be received.
There is some time lag betweeen the picture and the sound. You can see lip motion that is delayed compared to the sound.
Storing the LCD television for a period of more than 2 to 3 months without use might cause an unstable picture when the set is turned on.
Operating altitude: 800 to 1,114hPa (6,194ft to -2,484ft). Operating temperature: 41 F to 95 F. Avoid operating the LCD TV below 41 F LCD response speed may slow down when operating at these temperatures.
This is a normal operating characteristic of the LCD monitor.
Storage Altitude: 300 to 1,114hPa (31,912ft to -2,484ft). Storage temperature: 5 F to 140 F. Frequent use of the Power ON or OFF might trigger the power protection circuit. If the TV does not turn ON, please wait
a little before turning ON again.
TM
System Frequently Asked Questions
Some channel numbers in the Guide are incorrect.
You can correct them using Change Channel Display under Setup.
I have not received any Guide show listings.
Listings usually begin to appear within 24 hours after a successful Setup. It may take up to 5 days to receive a full 8 days of program listings.
A show I set to Record did not occur.
The TV did not tune to a show I scheduled with the Reminder feature.
I set a show to Auto-Tune and it did not.
Useful Information
• Check the connections between the TV, cable, antenna, and the IR cable if using a cable box.
• Verify Setup information under Change System Settings.
• Make sure the cable box is On, if applicable.
• Review Screen 4 and Screen 5 in the Initial Guide Setup section.
• Make sure your recorder is turned Off before the recording begins.
• Make sure there is a tape or DVD in the VCR or DVD Recorder.
• Check the Schedule menu and verify that the show is listed before recording begins.
• Check the placement of the IR cable in front of your recorder.
• Check the Schedule menu and verify that the show is listed.
• If you have a cable box, check the IR cable.
• Check the Schedule menu and verify that the show is listed as a Reminder.
• Highlight the show under Listings and do the following:
• Press the Menu button on the remote.
• Use the down arrow to highlight Edit Reminder, and press SELECT.
• Verify the Auto-Tune option reads Yes.
• The TV must be On at the scheduled time for Auto-Tune.
I set a show with the Power On TV option and it did not.
• Check the Schedule menu and verify that the show is listed as a Reminder.
• Highlight the show under Listings and do the following:
• Press the Menu button on the remote.
• Use the down arrow to highlight Edit Reminder, and press SELECT.
• Verify the Power On TV option reads Yes.
• The TV must be Off at the scheduled time for Power On TV.
72
Troubleshooting
TV Guide On-ScreenTMFrequently asked quiestions continued
If I add a recorder or change my cable service, how do I change my Setup information?
1) Highlight the Setup Service in the Guide.
2) Use the down arrow to select Change System Settings.
3) Follow the on-screen instructions.
A show entry in the Guide reads “No Listing.” What does that mean?
Show information for that entry was not available during the last Guide information update (download). Show information is updated on a daily basis.
When I entered the Guide, I was asked to choose from more than one channel lineup. What should I do?
Select the lineup that most closely matches the one for your area. If after you choose the lineup, you want to make changes to:
1) Highlight the Setup Service in the Guide.
2) Use the down arrow to select Change Channel Display.
3) Follow the on-screen instructions.
Remind feature. Highlight Schedule and press menu. Choose the event type, press SELECT and then enter date, start and stop time, channel number, etc.
What do the frequencies for Record and Remind mean?
Once—records/reminds the show one time
Daily (manual only)—records/reminds the time, channel, and input combination Monday through Friday
Regularly— records/reminds for the channel/time combination on any day of the week, on the same channel
Weekly— records/reminds for the channel/ time combination on a specific day of the week
Off (not cancel)—keeps the show in the list but will not record/remind the show until the frequency is changed
How can I look for a specific show in the Guide?
Search lets you find shows by Category (HDTV, Movies, Sports, Children, Educational, News, Variety, Series), Keyword, or Alphabetical.
What do the color for shows in the Listings and Search screens indicate?
Green=Sports; Dark Blue=Children’s; Purple=Movies; Teal=Other Show
If I have a power outage, do I need to complete Setup again?
No; Setup information is stored in TV Guide On Screen.
Is Help available in the Guide? If so, how do I find it?
Yes. Highlight any of the 5 main Services (i.e., Listings, Schedule, Recordings, Setup, Search) and press the Info Button. An Expanded Info Box displays additional help information; press Info again to close the box.
Help is also available in a Panel Menu. Press the Info Button to display an Expanded Info Box; press Info again to close the box.
After some show titles, I have noticed from 1 to 4 stars (****). What does that mean?
These stars are a broadcast-industry rating system used to inform you of a show’s quality. The more stars, the better the rating.
I have seen the word “download” in reference to the Guide. What does that mean?
A download sends channel and show information to a TV Guide On Screen device. A download happens at least once a day.
In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide International, Inc.
The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates.
The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895; 6,418,556; 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.
Gemstar-TV Guide International Inc. and/or its related affiliates are not in any way liable for the accuracy or availability of the program schedule information or other data in the TV Guide On Screen system and cannot guarantee service availability in your area. In no event shall Gemstar-TV Guide International, Inc. and/or its related affiliates be liable for any damages in connection with the accuracy or availability of the program schedule information or other data in the TV Guide On Screen system.
Useful Information
Can I set a Record or Remind event without highlighting a show title in the Guide?
Yes. TV Guide On Screen has a Manual Record and
73
FCC Information
This device complies with part15 of the FCC Rules.Operation is subject to the following two conditions : (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.
Useful Info
Cable Compatible Television Apparatus- Tèlèvision câblocompatible, Canada.
AGENCY REGULATORY INFORMATION
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not
expressly approved by Hitachi America ,Ltd. Home Electronics Division may void the user’s authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations.
Any cables that are supplied with the system must be replaced with identical cables in order to assure compliance with FCC rules. Order Hitachi spares as replacement cables.
Note
This LCD Television receiver will display television closed captioning, ( or ), in accordance with paragraph 15.119 of the FCC rules.
INDUSTRY CANADA AGENCY REGULATORY INFORMATION
Useful Information
74
Features and Specifications
Features:
New Easy-to-Use On-Screen Menu Control (3 Language)
Downloadable V-Chip
IR OUT/G-LINK System Control
- Contr ol your components with one remote control.
- 2 IR Blaster cables included
Illuminated and Preprogrammed Remote Contr ol
• Power Management: ON/OFF via signal detection
• Picture Enhancement
• Input Signal Identification
• CableCARD compatible - Contact your local cable
• operator for mor e information HDMI (High Definition Multimedia Interface)(High
• Bandwidth Digital Content Pro tection V1.1 Compatible)
Photo Input (for your digital camera, USB drive or
memory card USB drive)
Technology
• TV Guide On Screen
Video:
1366 x 768 Display Resolution
IPS (In-Plane Switching Technology)
Wide Viewing Angle: More than 160°
TM
Color Temperature Presets: High, Standard,
Medium and B/W .
Multiple Screen Fill Modes
(4:3 Standard/4:3 Expanded/4:3 Zoom 1/
4:3 Zoom 2/16:9 Standard1/Standard2/16:9 Zoom)
4MB 10-bit 3D Y/C Comb Filter
Picture Modes :Day(Normal), Day(Dynamic) and Night
Inputs:
Power Input . . . . . . . . . . . . . . . . . . . . .AC 120V, 60Hz
Power Consumption
- Refer to rear panel at the back of the LCD Television
Receiver
Antenna input impedance . . . . . . . . . . . . . . . .75 Ohm
Channel coverage . . . . . . . . . . . . . . . . . . . . . . . 191ch.
VHF-Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ~ 13
UHF-Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ~ 69
CATV Mid Band . . . . . . . . . . . . . . . . . . . . . . A-5 ~ A-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-I
Super Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J-W
Hyper Band . . . . . . . . . . . . . . . . . . . . . . . W+1 - W+28
Ultra Band . . . . . . . . . . . . . . . . . . . . . . . W+29 - W+94
Television System . . . . . . . . . . . . . . . NTSC Standard
Video . . . . . . . . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm
S-Video
Luminance (Y) . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm
Chrominance (C) . . . . . . . . . . . . . 0.286Vp-p, 75 Ohm
Component Video
Luminance (Y) . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm
Chrominance (PB/PR) . . . . . . . . . . . 0.7Vp-p, 75 Ohm
Audio input Impedance . . . . . . . . . . . . . . . . 270k Ohm
Average input level . . . . . . . . . . . . . . . . . . . 470mVrms
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (19 PIN)
ATSC Standard (8 VSB, 64-QAM, 256-QAM)
1
Outputs:
Video1.0Vp-p. 75 Ohm
Audio . . . . . . . . . . . . . . . . . . . . . . .470mVrms, 1k Ohm
Optical Out (Digital Audio) . . . . . .1 Optical Connector
Audio:
MTS Stereo/SAP
Bass Boost
Surround Sound
20W
Soft Mute (50%)
Supplied Accessories:
Remote Control
Batteries (AA)
6' AC Power cord cable
Table Top Stand
IR Blaster Cables
Power Swivel Cable
Ferrite Core
Optional Accessories:
For U.S. Models: Please access our website:
www.hitachi.us/tv
INPUTS/OUTPUTS
Wideband Component Y, Pb,Pr . . . . . . . . . . . . . . . . 3
Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
S-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Antenna (RF)Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Audio Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Monitor Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Optical Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
IR Blaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
G-LINK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CableCARD Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Upgrade Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Swivel Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Photo Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SPECIFICATIONS
Pixel Pitch . . . . 0.60(horiz.) x 0.60(vert.) mm.
FCC class: . . . . . . . . . . . . B for Consumer Use
Power Requirements:. . . . . . . . 108-132VAC, 60Hz
1
Screen mode availability varies by input format
HDTV Televisions display HDTV only when an HDTV source is available.
All specifications, weights, and dimensions are subject to change without prior notice. Please access www.hitachi.com/tv for detailed specifications and dimensions for custom installations.
UltraVision Digital is a registered trademark of Hitachi Home Electronics (America), Inc.
㪚㪦㪧㪰㪩㪠㪞㪟㪫㩷㪺㩷㪈㪐㪐㪐㪄㪉㪇㪇㪍㩷㪤㪦㪥㪫㪘㪭㪠㪪㪫㪘㩷㪪㪦㪝㪫㪮㪘㪩㪜㪃㩷㪠㪥㪚㪅㩷㪘㪣㪣㩷㪩㪠㪞㪟㪫㪪㩷㪩㪜㪪㪜㪩㪭㪜㪛㪅
Interface are trademarks or registered trademarks of HDMI Licensing LLC.
*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia
Useful Information
75
Set Dimensions
37 Inch Models (Includes Table Top Stand) Weight (lbs./kg): 63.9/29
B
E
D
B
C
62.9
D
28-9/16
725.7
Units
A
Inches
37-3/8 2-1/2 2-1/2
MM
62.9
949.4 485.3
J
E
26-3/16
664.3
F
19-1/8
A
F
16-11/16
I
G
424.1.
H
14-1/4
362.7
C
I
32-7/16
823.6
H
G
K
J
18-5/16 4-3/4
464.8
120.9 20.2
L
L
3-15/16
3/4
K M
N
M
100.7
N
14-3/8
365
Useful Information
76
Hitachi
Service Hotline
To locate an authorized HITACHI
service facility in the continental
U.S.A. and Canada,
DIAL TOLL FREE
7 days a week, 24 hours a day
1-800-HITACHI
(1-800-448-2244)
HITACHI AMERICA, LTD. HOME ELECTRONICS DIVISION
HITACHI has made every effort to assure you hours of trouble free operation from your unit. However, should you require service, a network of HITACHI Authorized Service Facilities has been established in all 50 states and Puerto Rico. Each facility will provide you with convenient and expedient assistance. Our service hotline operator will direct you to the HITACHI Authorized Service Facility nearest you. Just present proof of purchase and/or delivery receipts to the Hitachi Authorized Service Facility, and service will be rendered in accordance with the terms of the limited warranty as stated on your warranty card or operating guide.
Should you have any questions regarding warranty, service, operation, or technical assistance, please contact:
Hitachi America, LTD. Home Electronics Division 900 Hitachi Way Chula Vista, CA 91914-3556
HITACHI CANADA, LTD. DIGITAL MEDIA DIVISION
Should you have any questions regarding warranty, service, operation, or technical assistance, please contact:
In Canada: 1-800-HITACHI (1-800-448-2244)
Monday – Friday (EST).........................9:00am – 7:00pm
Saturday (EST) .....................................9:00am – 5:00pm
Look for your French Manual on the outside of the box. If the manual is missing, call 1-800-HITACHI (1-800-448-2244) for a copy.
Useful Information
Pour de plus amples renseignements sur le service durant la période couverte par la garantie, sur le fonctionnement ou pour de l’assistance technique communiquez avec:
Au Canada: 1-800-HITACHI (1-800-448-2244)
Lundi - Vendredi L’EST ........................9:00am – 7:00pm
Samedi L’EST.......................................9:00am – 5:00pm
La version français de votre manual se trouve a l’exterieur de la boîte. Si le manuel est manquant, coposez le 1-800-HITACHI (1-800-448-2244) pour obenir votre copie.
HITACHI CANADA, LTD. 1-2495 Meadowpine Blvd. Mississauga, Ontario L5N 6C3
77
Service Information
When you call HITACHI SERVICE HOTLINE they will require some information related to the TV MODEL NAME and SERIAL # in order to give you the proper support. This information is located on the back of the TV and also on the RIGHT SIDE of your TV set. Please follow the next steps to find this information and then provide to SERVICE.
Look on the right side of the TV.
Locate the LABEL where it shows the information related to MODEL NAME and SERIAL #.
HITACHI Service Department will require this information in order to give you the proper support regarding your questions.
Useful Information
78
End User License Agreement for HITACHI DTV Software
END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE
IMPORTANT – READ CAREFULLY: This End User License Agreement for HITACHI DTV Software (this “Agreement”) is a legal agreement between you (“you” or “your”), in your capacity as the owner of a HITACHI brand digital television (the “DTV”), and HITACHI America, Ltd., Ubiquitous
Platform System Division ("HITACHI"). By using the DTV or the digital television software installed on the DTV (the "DTV Software") or any Upgrade (as defined below, and together with the DTV Software, the “Software”), you agree to be bound by the terms and conditions of this
Agreement. IF YOU DO NOT AGREE TO BE BOUND BY THIS LICENSE AGREEMENT, DO NOT USE THE DTV OR THE DTV SOFTWARE.
1. LICENSE GRANT. HITACHI grants to you, for the life of the DTV, a
non-exclusive, non-transferable, revocable license to install and use one copy of the Software on the DTV, subject to the following limitations and restrictions: a. You may not share, duplicate, republish or redistribute the
Software;
b. You may not resell, rent, lease, sublicense, gift, loan, assign or
otherwise transfer the Software or any of your rights under this Agreement;
c. You may not modify, adapt, translate, reverse engineer,
decompile, disassemble or make derivative works from the Software or use the Software in combination with any non-
Hitachi software; and
d. You may not use the Software for any commercial purpose.
2. VIOLATIONS; INDEMNITY. You understand and agree that your
use of the Software in any manner except as permitted under this Agreement could constitute a serious crime and could subject you to damages and an award to HITACHI of attorneys’ fees in connection with your violation of this Agreement. You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights caused or facilitated by your failure to abide by the terms of this Agreement. You agree to defend, indemnify and hold HITACHI and its parent and affiliate companies harmless from and against any and all liability resulting from any breach by you of this Agreement.
3. INTELLECTUAL PROPERTY. The Software is protected by federal
copyright laws, international copyright treaties and other intellectual property laws and treaties. The Software is licensed, not sold, to you. All right, title and interest in and to the Software and any intellectual property associated therewith, including any accompanying printed materials, shall belong to HITACHI and its licensors and suppliers. Except as expressly provided herein, neither HITACHI nor any of its licensors or suppliers grants to you under this Agreement any express or implied right in or to any patents, copyrights, trademarks, trade secrets or other intellectual property. All right, title and interest in and to the intellectual property rights associated with any content that is accessible through use of the Software shall belong to the applicable content owners and may be protected by copyright or other intellectual property laws and treaties. This Agreement grants you no rights to use such content. Any rights of HITACHI not expressly granted to you hereunder are reserved expressly by Hitachi.
4. SOFTWARE UPGRADES. In the future, HITACHI may release or
make available one or more upgrades to the DTV Software (each, an “Upgrade”). You understand and agree that if you decide to install or use any Upgrade, your installation and use of such Upgrade and/or any other software or intellectual property HITACHI may provide in connection therewith shall be governed by the terms and conditions of this Agreement, except to the extent that HITACHI provides different or supplementary license terms or conditions that accompany such Upgrade or other software or intellectual property. In the event HITACHI provides you with a “flash card” or other media to effect or facilitate an Upgrade, you understand and acknowledge that your failure to return such flash card or other media to HITACHI as HITACHI may require could result in HITACHI placing your name and your DTV’s serial number on a “No Further Upgrades” list, which will prohibit you from receiving any subsequent Upgrades HITACHI may later release or make available. IF YOU DO NOT AGREE WITH ALL THE TERMS
AND CONDITIONS OF THIS AGREEMENT OR ALL THE TERMS AND CONDITIONS OF ANY DIFFERENT OR SUPPLEMENTARY LICENSE THAT MAY ACCOMPANY SUCH UPGRADE, (A) DO NOT USE ANY HITACHI-PROVIDED FLASH CARD OR OTHER MEDIA, (B) DO NOT INSTALL ANY HITACHI-PROVIDED UPGRADE SOFTWARE ON YOUR DTV, AND (C) PROMPTLY RETURN SUCH FLASH CARD OR OTHER MEDIA TO HITACHI.
5. EXPORT RESTRICTIONS. HITACHI is licensing the Software for use within North America only. You agree that you will not export or re-export the Software. You specifically agree not to export or re­export the Software: (i) to any country to which the U.S. has embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Libya, North Korea, Sudan and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development, or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the U.S. Bureau of Industry and Security nor any other U.S federal Agency has suspended, revoked, or denied your export privileges.
6. NO WARRANTIES. The software is provided to you in "as is” condition and HITACHI makes no warranties of any kind whatsoever regarding the software and, to the maximum extent permitted by law, hereby expressly disclaims all warranties of any kind whatsoever, express or implied, with respect to the software. All implied warranties, including without limitation, the implied warranties of non-infringement, merchantability and fitness for a particular purpose are hereby expressly disclaimed by hitachi to the maximum extent permitted by law.
7. LIMITATION OF LIABILITY. To the maximum extent permitted by applicable law, HITACHI, its licensors, suppliers, parent companies, affiliates, subsidiaries, employees and agents shall not under any circumstances be liable to you or any third parties for any damages of any nature arising in any way from this agreement, your use of the software or otherwise, whether indirect, special, incidental, consequential or otherwise, including, without limitation, any claims for lost profits, lost good will, lost data, business interruption, procurement of substitute goods or services, or expenditures made or committed for in reliance on the continuation of this agreement, even if advised in advance of the possibility of such damages.
8. NO FAILURE OF ESSENTIAL PURPOSE. You agree that neither HITACHI' S breach of this agreement nor its failure to repair a
defect, error or bug in the software shall constitute a failure of the essential purpose of this agreement.
9. CRYPTOGRAPHIC SOFTWARE. The software contains software developed by the OpenSSL Project, including cryptographic software written by eric young (the "cryptographic software"). The cryptographic software is provided by the OpenSSL Project in "as is'' condition and any express or implied warranties, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose are hereby expressly disclaimed to the maximum extent permitted by law. In no event shall the OpenSSL Project, its contributors, HITACHI or any of its parent or affiliate companies be liable for any direct, indirect, incidental, special, exemplary, or consequential damages (including, but not limited to, procurement of substitute goods or services; loss of use, data, or profits; or business interruption) however caused and on any theory of liability, whether in contract, strict liability, or tort (including negligence or otherwise) arising in any way out of the use of the software or the cryptographic software, even if advised in advance of the possibility of such damages.
10. TERMINATION. HITACHI may terminate this Agreement immediately at any time by providing notice to you.
11. GOVERNING LAW; SEVERABILITY. This Agreement will be governed by the laws of the State of New York, and you consent to the exclusive jurisdiction and venue in the federal courts sitting in the Southern District of New York, unless no federal subject matter jurisdiction exists, in which case you consent to the exclusive jurisdiction and venue in the Borough of Manhattan, New York, USA.
License Agreements
79
End User License Agreements for Operating System Software
SOFTWARE LICENSE INFORMATION
Your HITACHI brand digital television (the “DTV”) uses certain open source operating system software (the “OS Software”) distributed pursuant to GNU GENERAL PUBLIC LICENSE Version 2 and GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, each as defined and published by the Free Software Foundation, Inc.
The OS Software modules incorporated into the DTV are listed in the table below opposite the applicable GNU software license. Copies of such GNU software licenses are provided in the pages that follow.
Software Module Applicable GNU Software License
Linux Kernal busybox dhcpdcd ifupdow net-tool iptables libstdc++5
glibc libposixtime
For purposes of incorporating the OS Software into the DTV, Hitachi made certain modifications to the source code of the OS Software (collectively, the “Source Code Modifications”) in 2006. The Source Code Modifications also are distributed pursuant to the applicable GNU software licenses identified above.
THE OS SOFTWARE AND THE SOURCE CODE MODIFICATIONS ARE PROVIDED “AS IS” AND THE LICENSEE DISCLAIMS ANY AND ALL WARRANTIES OF ANY KIND, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for additional terms and conditions.
If you would like to learn more about the Free Software Foundation or the GNU software project, please visit http://www.fsf.org. If you would like to request a copy of the Source Code Modifications from HITACHI, please send an email to the following address: tvsoftwaresupport@hhea.hitachi.com
GNU GENERAL PUBLIC LICENSE
Version 2
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1
License Agreements
80
End User License Agreement for Operating System Software
GNU GENERAL PUBLIC LICENSE Version 2, June 1991
Copyright © 1989, 1991 Free Software Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
(YHU\RQHLVSHUPLWWHGWRFRS\DQGGLVWULEXWHYHUEDWLPFRSLHVRIWKLVOLFHQVHGRFXPHQWEXWFKDQJLQJLWLVQRWDOORZHG
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General PublicLicense is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not
UHÀHFWRQWKHRULJLQDODXWKRUVUHSXWDWLRQV
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and PRGL¿FDWLRQIROORw.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may
The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim
(Hereinafter, translation is included without limitation in the term
PRGL¿FDWLRQ(DFKOLFHQVHHLVDGGUHVVHGDV\RX
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a)
You must cause the modified files to carry prominent notices stating that you changed the ¿OHV and the date of any change.
b) You must cause any work that you distribute or publish, that
in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands
interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. ([FHSWLRQ if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identL¿DEOH sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply
But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and
.esneciL cilbuP lareneG siht fo smret eht rednu detubirtsid eb
every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or
.egaugnal rehtona otni detalsnart ro/dna snoitacifidom htiw ro
collective works based on the Program.
License Agreements
.skrow etarapes sa meht etubirtsid uoy nehw snoitces esoht ot
81
End User License Agreement for Operating System Software
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:
The source code for a work means the preferred form of the work for making PRGL¿FDWLRQV to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface GH¿QLWLRQ ¿OHV plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license
License Agreements
from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.
a)
Accompany it with the complete corresponding machine­readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
b)
Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
c) Accompany it with the information you received as to
the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all.
For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be torefrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable underany particular circumstance, the balance of the section is intended toapply and the section as a whole is intended to apply in othercircumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or .emit ot emit morf esneciL cilbuP lareneG eht fo snoisrev wen
Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program VSHFL¿HV a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free
programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
82
End User License Agreement for Operating System Software
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source ¿le to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.
<one line to give the program's name and a brief idea of what it does.> Copyright © <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright © year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details.
The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than `show w' and `show c'; they could even be mouse-clicks or menu items-­whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which makes passes at compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989 Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General Public License instead of this License.
License Agreements
83
End User License Agreement for Operating System Software
GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999
Copyright © 1991, 1999 Free Software Foundation, Inc. 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
[This is the ¿UVW released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you ¿UVW think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modi¿ed by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be
FRQVLVWHQWZLWKWKHIXOOIUHHGRPRIXVHVSHFL¿HGLQWKLVOLFHQVH
Most GNU software, including some libraries, is covered by the
License Agreements
ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.
Preamble
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.
We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non­free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a
.seirarbil eerf-non desu ylediw sa boj emas eht seod yrarbil eerf In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in non­free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/ Linux operating system.
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to UXQWKDWSURJUDPXVLQJDPRGL¿HGYHUVLRQRIWKH/LEUDUy.
The precise terms and conditions for copying, distribution and PRGL¿FDWLRQ follow. Pay close attention to the difference between
."yrarbil eht sesu taht krow" a dna "yrarbil eht no desab krow" a The former contains code derived from the library, whereas the latter must be combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".
A "library" means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.
The "Library", below, refers to any such software library or work which has been distributed under these terms. A "work based on the Library" means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with PRGL¿FDWLRQV and/or translated
84
End User License Agreement for Operating System Software
straightforwardly into another language. (Hereinafter, translation
LVLQFOXGHGZLWKRXWOLPLWDWLRQLQWKHWHUPPRGL¿FDWLRQ
"Source code" for a work means the preferred form of the work for making PRGL¿FDWLRQV to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface GH¿QLWLRQ ¿OHV plus the scripts used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing LW Whether that is true depends on what the Library does and what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
D 7KHPRGL¿HGZRUNPXVWLWVHOIEHDVRIWZDUHOLEUDUy.
E You must cause the files modified to carry prominent
notices stating that you changed the ¿OHV and the date of any change.
F You must cause the whole of the work to be licensed at no
charge to all third parties under the terms of this License.
G If a facility in the PRGL¿HG Library refers to a function or a
table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. (For example, a function in a library to compute square roots has a purpose that is entirely well-de¿Qed independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply
LWWKHVTXDUHURRWIXQFWLRQPXVWVWLOOFRPSXWHVTXDUHURRWV
These requirements apply to the modified work as a whole. If GHQWL¿DEOH sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply
But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is
to exercise the right to control the distribution of derivative or collective works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the LibraU\ on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has
Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of it, under Section  in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine­readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.
However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library, rather than a "work that uses the library". The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.
When a "work that uses the Library" uses material from a header ¿OH that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The WKUHVKROGIRUWKLVWREHWUXHLVQRWSUHFLVHO\GH¿QHGE\ODw.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in lHQJWK then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus
.skrow etarapes sa meht etubirtsid uoy nehw snoitces esoht ot
SRUWLRQVRIWKH/LEUDU\ZLOOVWLOOIDOOXQGHU6HFWLRQ
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section
6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library to produce
.hsiw uoy fi daetsni noisrev taht yficeps nac uoy neht ,deraeppa
License Agreements
85
End User License Agreement for Operating System Software
a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit
PRGL¿FDtion of the work for the customer's own use and reverse HQJLQHHULQJIRUGHEXJJLQJVXFKPRGL¿FDWLRQV
You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this /LFHQVH You must supply a copy of this /LFHQVH If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this /LFHQVH Also, you must do one of these things:
a) Accompany the work with the complete corresponding
b) Use a suitable shared library mechanism for linking with
c) Accompany the work with a written offer, valid for at least
d) If distribution of the work is made by offering access to copy
e) Verify that the user has already received a copy of these
For an executable, the required form of the "work that uses the Library" must include any data and utility programs needed for reproducing the executable from iW However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that
FRPSRQHQWLWVHOIDFFRPSDQLHVWKHH[HFXWDEOH
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating V\VWHP Such a contradiction means you cannot use both them and the Library together in an
H[HFXWDEOHWKDW\RXGLVWULEXWH
 You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is
License Agreements
otherwise permitted, and provided that you do these two things:
a) Accompany the combined library with a copy of the same
machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable "work that uses the Library", as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the
DSSOLFDWLRQWRXVHWKHPRGL¿HGGH¿QLWLRQV
the Library A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a PRGL¿HG version of the library, if the user installs one, as long as the modified version is interface-compatible with the version
WKDWWKHZRUNZDVPDGHZLWK
three years, to give the same user the materials VSHFL¿HG in Subsection 6a, above, for a charge no more than the cost of
SHUIRUPLQJWKLVGLVWULEXWLRQ
from a designated place, offer equivalent access to copy
WKHDERYHVSHFL¿HGPDWHULDOVIURPWKHVDPHSODFH
materials or that you have already sent this user a copy
work based on the Library, uncombined with any other library IDFLOLWLHV This must be distributed under the terms of
WKH6HFWLRQVDERYH
b) tcaf eht fo yrarbil denibmoc eht htiw eciton tnenimorp eviG
that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the
VDPHZRUN
8 You may not copy, modify, sublicense, link with, or distribute
esneciL siht rednu dedivorp ylsserpxe sa tpecxe yrarbiL eht Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this LiFHQVH However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full
FRPSOLDQFH
9 You are not required to accept this License, since you have not signed LW However, nothing else grants you permission to modify or distribute the Library or its derivative ZRUNV These actions are prohibited by law if you do not accept this LiFHQVH Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or
PRGLI\LQJWKH/LEUDU\RUZRUNVEDVHGRQLW
 Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions You may not impose any further restrictions on the recipients' exercise of the rights granted hereiQ You are not responsible for enforcing compliance by third
SDUWLHVZLWKWKLV/LFHQVH
11 If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other
FLUFXPVWDQFHV
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is
LPSOHPHQWHGE\SXEOLFOLFHQVHSUDFWLFHV0DQ\SHRSOHKDYHPDGH
generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee
FDQQRWLPSRVHWKDWFKRLFH
This section is intended to make thoroughly clear what is
EHOLHYHGWREHDFRQVHTXHQFHRIWKHUHVWRIWKLV/LFHQVH
12 If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in
86
End User License Agreement for Operating System Software
or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or
If the Library specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of
If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License).
It is safest to attach them to the start of each source ¿le to most effectively convey the exclusion of warranty; and each ¿OH should have at least the "copyright" line and a pointer to where the full notice is found.
<one line to give the library's name and a brief idea of what it does.> Copyright © <year> <name of author>
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public
.rebmun noisrev gnihsiugnitsid a nevig si noisrev hcaE .snrecnoc
.noitadnuoF erawtfoS eerF eht yb dehsilbup noisrev retal yna
.yrarbil eht ot seciton gniwollof eht hcatta ,smret eseht ylppa oT
License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by James Random Hacker.
<signature of Ty Coon>, 1 April 1990 Ty Coon, President of Vice
That's all there is to it!
License Agreements
87
Appendixes
Appendixes
Appendix A:
Picture Format for Each Input Source
Aspect Specifications
Input A uto Aspect Aspect
S ignal Aspect Video ID 16:9
ANT
Analog
ANT YCBCR480p No 16x 9 Yes
Digital 480i
Input 1 HDMI 1080i/720p
Input 2 HDMI 1080i/720p No 16x9 Yes Ye s Ye s
Input 3 Y PBPR1080i/720p No 16x9 Yes Ye s Yes
Video NTSC No 4x 3 Y es No Ye s Y es Ye s Y es Y es
No
YPBPR1080i/720p
480p Auto ON 16x9 Y es Initial
480i Letter
Video NTSC Auto ON 16x 9 Y es Initial
S-Video Letter
480p Auto ON 16x9 Y es Initial
480i Letter
Video NTSC Auto ON 16x 9 Y es Initial
S-Video Letter
480p Auto ON 16x9 Y es Initial
480i Letter
No Signal
Video NTSC Auto ON 16x 9 Y es Initial No Ye s
No
No
No Info Yes
Auto OF F No Ye s
Auto OF F No Ye s
No Info Yes
Auto OF F No Ye s
Auto OF F No Ye s
Auto OF F No
No No
Auto OF F No
Standard 1
4x3 No
16x9 Yes Yes Ye s
16x9 Yes Yes Ye s
4x3
4x3
No ID Yes
4x3
4x3
No ID Yes
4x3
No ID Yes
Letter
4x3
No ID Yes
Standard 2
No No No
No No No
No No No
No No No
No No No
No No No
No No No
No No No
No No No
No No No
No No No
No No No
16:9
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes : Selectable No : Un -
16:9
Zoom
Ye s No Ye s No No
No Ye s Ye s Y es Y es
Ye s
Ye s Y es Ye s Y es Ye s
Ye s Y es Ye s Y es Ye s
Ye s
Ye s Y es Ye s Y es Ye s
Ye s Y es Ye s Y es Ye s
Ye s
Ye s Y es Ye s Y es Ye s
Ye s Y es Ye s Y es Ye s
Ye s
Ye s Y es Ye s Y es Ye s
Ye s Y es Ye s Y es Ye s
Ye s
Ye s Y es Ye s Y es Ye s
Ye s Y es Ye s Y es Ye s
4:3
Standard
No
No
No
Ye s Y es Ye s Initial Ye s
Ye s Y es Initia l Y es Ye s
No No No No
Ye s Y es Ye s Initial Ye s
Ye s Y es Initia l Y es Ye s
No
No No No No
Ye s Y es Ye s Initial Ye s
Ye s Y es Initia l Y es Ye s
No No No No
Ye s Y es Ye s Initial Ye s
Ye s Y es Initia l Y es Ye s
No
No
Ye s Y es Ye s Initial Ye s
Ye s Y es Initia l Y es Ye s
No No No No
Ye s Y es Ye s Initial Ye s
Ye s Y es Initia l Y es Ye s
4:3
Ex panded
Ye s
Ye s
No
Ye s
Ye s
No
Zoom 1
Selectable
4:3
Zoom 2
No No
No No
No No
No No
No No
No No
4:3
88
Appendixes
Aspect Specifications
(Continuation)
Input Auto Aspect Aspect
S ignal As pect Video ID 16:9
Input 4 Y PBPR1080i/720p No 16x9 Y es Y es Ye s
480p Auto ON 16x9 Y es Initial
480i Letter
No Signal
V ideo NT S C Auto O N 16 x9 Y es I nitial
Input 5 HDMI 1080i/720p No 16x9 Yes Y es Y es No Yes
YPBPR1080i/720p No 16x9 Yes Yes Y es No Ye s No No
No Signal
V ideo NT S C Auto O N 16 x9 Y es I nitial No Ye s
Auto OF F No
No No
Auto OF F No
480p
Auto ON 16x9 Y es Initial No Ye s
480i
No Info Yes
Auto OF F No Ye s
480p
Auto ON 16x9 Y es Initial No Ye s
480i
Auto OF F No
No No
Auto OF F No
Standard 1
No No No
4x3
No ID Yes
L ette r
4x3
No ID Yes
L ette r
4x3
L ette r
4x3
No ID Yes No Ye s Y es Ye s Ye s Y es
L ette r
4x3
No ID Yes No Ye s Y es Ye s Ye s Y es
No No No
No
No No No
No No No
No No No
No No No
No No No
No No No
No No No
16:9
Standard 2
No
No
No
No No
No
No
No
16:9
Zoom
Ye s
Ye s Ye s Ye s Ye s Y es
Ye s
Ye s Ye s Ye s Ye s Y es
Ye s Ye s Ye s Ye s Y es
Ye s Ye s Ye s Ye s Y es
Yes : Selectable No : Un - Selectable
4:3
Standard
No
No
Yes Yes Yes Initial Yes
Ye s Y es Initial Ye s Ye s
No No No No
Yes Yes Yes Initial Yes
Ye s Y es Initial Ye s Ye s
No No No No
Yes Yes Yes Initial Yes
Ye s Y es Initial Ye s Ye s
No No No No
Yes Yes Yes Initial Yes
Ye s Y es Initial Ye s Ye s
No No No No
Yes Yes Yes Initial Yes
Ye s Y es Initial Ye s Ye s
4:3
Ex panded
Ye s
No No No
4:3
Zoom 1
No No
No No
4:3
Zoom 2
89
Appendixes
Index
Photo Input . . . . . . . . . . . . . . . . . . . . . . . . . .27
Power Swivel . . . . . . . . . . . . . . . . . . . . . .5,8,69
A
Accessories, . . . . . . . . . . . . . . . . . . . . . . . . . .4
Antennas (Connecting), . . . . . . . . . . . . . . . . .7
Aspect Ratio, . . . . . . . . . . . . . . . . . . . . .25, 46
Audio
Bass Boost . . . . . . . . . . . . . . . . . . . . . . . .47
Audio Settings . . . . . . . . . . . . . . . . . . . . . . .48
Audio Source . . . . . . . . . . . . . . . . . . . . . . . .48
Auto Noise Cancel . . . . . . . . . . . . . . . . . . . . .48
B
Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Bass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Black Enhancement . . . . . . . . . . . . . . . . . . . .44
Black Side Panel . . . . . . . . . . . . . . . . . . . . . .45
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . .43
C
CableCARD . . . . . . . . . . . . . . . . . . . . . . . . . .67
Caution and Safety Tips . . . . . . . . . . . . . . . .2-3
Channel Manager . . . . . . . . . . . . . . . . . . .52-53
Auto Channel Scan . . . . . . . . . . . . . . . . . . .52
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Closed Captions
Captions . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Color Temperature . . . . . . . . . . . . . . . . . . . . .44
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Contrast Mode . . . . . . . . . . . . . . . . . . . . . . . .44
E
External Video Source . . . . . . . . . . . . . . .18-22
TV Ratings (Canadian - French) . . . . . . . . .58
Alternate Ratings U.S. . . . . . . . . . . . . . . . . . .59
M
Menu Preference
Language . . . . . . . . . . . . . . . . . . . . . . . . . .62
Background . . . . . . . . . . . . . . . . . . . . . . . .63
Monitor Out . . . . . . . . . . . . . . . . . . . . . . . . . .66
N
Noise Cancel . . . . . . . . . . . . . . . . . . . . . . . . .48
P
Perfect Volume . . . . . . . . . . . . . . . . . . . . . . .48
Picture Mode . . . . . . . . . . . . . . . . . . . . . . . .43
Picture-in-Pictur e (PIP) . . . . . . . . . . . . . .30-32
R
Remote Control
Functions . . . . . . . . . . . . . . . . . . . . . . . .23-40
Programming Codes . . . . . . . . . . . . . . .39-40
Installing Batteries . . . . . . . . . . . . . . . . . . . .4
S
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . .63
Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Connecting External Speakers . . . . . . . . . .21
Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Split Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Index
F
Favorite Channel . . . . . . . . . . . . . . . . . . . . . .29
Freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . 24,32
H
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15,19
I
Input Setup . . . . . . . . . . . . . . . . . . . . . . .24,64
L
Language
Menu Language . . . . . . . . . . . . . . . . . . . . ..62
Locks
Change Access Code . . . . . . . . . . . . . . . . 54
Channel Lock . . . . . . . . . . . . . . . . . . . . . . .54
Front Panel Lock . . . . . . . . . . . . . . . . . . . .54
Movie Ratings . . . . . . . . . . . . . . . . . . . . . . .55
TV Ratings . . . . . . . . . . . . . . . . . . . . . . . . .56
TV Ratings (Canadian - English) . . . . . . . . .57
90
T
Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Tint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Treble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
TV Guide On ScreenTM. . . . . . . . . . . . . .49-51
V
Video Settings . . . . . . . . . . . . . . . . . . . . .43
W
White Balance . . . . . . . . . . . . . . . . . . . . . . . .45
-46
Notes
91
Notes
92
Notes
93
Notes
94
Notes
95
QR68671
Loading...