AM NOITAREPO S’RESU
LAUN
X08060287B
,ylhg
uoroht launam siht daer esaelp ,tinu siht gnitarepo erofeB
ecnerefer erutuf rof niater dna
NOTE
The manufacturer reserves the right for any modifications
on the product which might be deemed necessary or
useful without informing about it in this IFU.
Thank you for choosing a Hisense washing machine.
Before operating your new washing machine, please read
this instruction carefully, and keep it for future reference.
Please make sure the socket is grounded securely, the
water source connection is reliable. The manufacturer
declines all liability and warranty for damage to property
or injury to persons or animals due to non-compliance
with the directions given in this instruction.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
The new hose-sets supplied with the appliance are to be
used and that old hose-sets should not be reused.
This appliance can be used by children aged from 8 years
and above and persons with reduced physical. Sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction
concerning use of the appliance in a safe way and
understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user
supervision.
maintenance shall not be made by children without
Children of less than 3 years should be kept
away unless continuously supervised.
The maximum permissible inlet water pressure, 1 MPa,
for appliances intended to be connected to the water
mains.
The minimum permissible inlet water pressure, 0.1 MPa, if
this is necessary for the correct operation of the appliance
For washing machines with ventilation openings in the
base, that a carpet must not obstruct the openings.
ensure
Ensure
Ensure that the ventilation openings in the base of the washing machine
(if available on your model) are not obstructed by a carpet or other material.
Single inlet -
Dual inlet -
only
and cold
21
ing
the
that
that
The symbol on the product, or on the documents accompanying the product,
indicates that this appliance may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for there cyclingof electrical
and electronic equipment. Disposal must be carried out in accordance with local
environmental regulations for waste disposal. For more detailed information about
treatment, recovery and recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you purchased
the product.
en
from the mains supply,
,
3
the
4
Clean the outside
of the washing machine with a damp cloth. Do not use abrasive
detergents.
Never open the door forcibly or use it as a step.
DESCRIPTION OF THE WASHING MACHINE
1
2
4
7
is
while the
for
can
for
7
Control panel layout and
appearance will depend on the model.
while the
to be
BEFORE THE FIRST
To remove any residual water used during testing by the manufacture r, we
recommend that you carry out a short wash cycle without laundry.
1 Open the tap.
2 Close the door.
3 Pour a little detergent (about 30 ml) into the main wash chamber of the deter-
1
2
4
gent dispenser .
4. Select and start a short programme (see separate quick reference guide).
WASH CYCLE
PREPARATION OF THE WASHING
1. Sort the laundry according to...
Type of fabric / care label symbol
Cottons, mixed fibres, easy care/synthetics, wool, handwash items.
The wool wash
Woolmark Company for the washing of Woolmark garments labelled as “machine
wash” provided that the garments are washed according to the instructions on the
is
garment label and those issued by the manufacturer of this washing machine.
Colour
Separate coloured and white items. Wash new coloured articles separately.
Loading
W
items
ash
distribution in the drum.
Delicates
Wash small
in a cloth bag or pillow case with zip. Always remove curtain rings or wash curtains
with the rings inside a cotton bag.
2. Empty all pockets
Coins, safety pins etc. can damage your laundry as well as the appliance drum and
tub.
3. Fasteners
Close zips and fasten buttons or hooks; loose belts or ribbons should be tied
together.
Stain removal
Blood, milk, eggs
programme.
cycle of this machine has been tested and approved by The
of different sizes in the same load to improve washing efficiency and
items (e.g. nylon stockings, belts etc.) and items with hooks (e.g. bras)
etc. are generally removed by the automatic enzyme phase of the
5
6
.
/ soak
U
7 8
unds
2
Depending on the model, Insert removal tool like
slotted screwdriver into the small opening of
bottom baffle, press the bottom baffle downward
with much strength and open it. Or, push down on
the tabs provided on both the sides and remove it.
9 1
0
fit
fit
11 12
solv
no screen are off.
and Choose the desired
programmme to start the machine.
The washing machine will not start, and the screen flashes.
Check if the water tap is closed.
the screen is flashing. Press the
the screen is flashing.
remove some
too
13 14
Hot / Cold fill fault - For Models with Dual Inlets
Fault Code List
If you wish to connect hot and cold water supply (Fig.1):
1. Fix the red marked inlet hose to the hot water tap and to the inlet valve with the red
filter on the rear side of machine.
2. Fix the other inlet hose to the cold water tap and to the inlet valve with the blue filter
on the rear side of the machine.
Make sure:
a) The connections are tightly fixed
b) Do not invert their position (for example: cold fill into hot inlet valve and vice versa).
If you wish to connect only the cold fill follow the below instructions (Fig. 2):
1. You will need a Y-piece connector. This can be purchased from local hardware or plumb
ing supplier.
2. Fix the Y-piece connector to the cold fill tap.
3. Connect the two inlet valves present on the rear part of the machine to the Y-piece
connector using the hoses provided.
Ensure that:
All connections are tightly fixed.
Do not allow children to operate, crawl on, be near or inside your washer.
Note that during the wash cycles, the surface temperature of the porthole door may
increase.
Close supervision of children is necessary when the appliance is used near children.
Displayed on Display Window Fault Description
“F01” Water inflow fault
“F03” Drainage fault
“F04”, “F05”, “F06”, “F07”，“F23” and “F02/F24”
“F13”
“F14” Door unlock fault
“Unb”
Electronic module fault, overflow or too much foam.
Door lock fault
Unbalance alarm
a. “F01” displayed on screen
The machine is not fed with water or insufficient water. Check:
• Faucet is fully open and has enough water pressure.
• Water inlet pipe is knotted or not.
• Filtering net of water inlet pipe is blocked or not (refer to maintenance and
repair).
• Water pipe is frozen or not.
Press “Start/Pause” key after fault is removed.
If fault occurs again, please contact with after-sale service (refer to after-sale
service.).
Hot fill
Cold fill
Cold fill
Y-piece
b. “F03” displayed on screen
The washer is not emptied. The washer stops the program being executed. Shut
down the machine and disconnect power supply. Check:
• Drain pipe is knotted or not.
Red inlet valve
Blue inlet valve
Fig.1
Red inlet valve
Blue inlet valve
Fig.2
• Filter in drain pump is blocked or not (refer to the cleaning of filter in drain pump)
Ensure that
15 16
C. Fault code
The washer stops when the program is running. The display window
shows fault code “F02/F24”, fault codes from “F04’ to “F07”, “F13”,“F14”,
“F23” or “Unb”.
If fault code “F02/F24” is shown
Water level reaches overflow level.
Remove it by pressing “Start/Pause” key and feed water.
Select and start required program. If fault occurs again, disconnect power supply
and contact with after-sale service.
If fault code “F04” to “F07”, “F23” shown
Electronic module fails.
Turn the nub to Off for 3 seconds to turn off the machine.
After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect
power supply and contact with after-sale service.
If fault code “F13” is shown
Door lock is abnormal. Start program for 20 sec and unlock the washer door
(PTC) to check whether the door is closed.
Open and close it again.
After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect
power supply and contact with after-sale service.
If fault code “F14” is shown
Door open fault..
Action: Press “Start/Pause” button. The washing machine will try to open the
door. The alarm will not be removed until the door is unlocked. Or, turn the nub to
Off for 3 seconds to turn off the machine. Choose the desired programmme to
start the machine. The alarm will be removed.
If fault code “Unb” is shown
Unbalance alarm.
Turn the nub to Off for 3 seconds to turn off the machine. Open the door and
re-tidy clothes and then rotate program knob to single dehydration mode. Spin
clothes to dry again.
If fault occurs again, disconnect power supply and contact with after-sale service.
adequate for the machine’s 10 A Current Rating.
The electrical power cable must be replaced exclusively by a licensed electrician.
17 18
Loading...