Hilti TE 7-C User Manual

TE 7-C
Operating instructions en
Mode d’emploi fr
Manual de instrucciones es
Manual de instruções pt
1
ThisProduct is Listed
Ce produit est homologué
Esteproduto está registrado
2
4 5
6 7
3
8 9
ORIGINAL OPERATING INSTRUCTIONS
TE 7C rotary hammer
It is essential that the operating instruc­tions are read before the power tool is op­erated for the first time.
Always keep these operating instructions together with the power tool.
Ensure that the operating instructions are with the power tool when it is given to other persons.
Contents Page
1. General information 1
2. Description 2
3. Insert tools, accessories 4
4. Technical data 4
5. Safety instructions 5
6. Before use 8
7. Operation 8
8. Care and maintenance 10
9. Troubleshooting 11
10. Disposal 12
11. Manufacturer’s warranty - tools 12
1 These numbers refer to the corresponding illustra­tions. The illustrations can be found on the fold-out cover pages. Keep these pages open while studying the operating instructions. In these operating instructions, the designation “the power tool” always refers to the TE 7-C rotary ham­mer.
Operating controls and parts 1
@ ; = % & ( )
en
Chucks Function selector switch Control switch Forward / reverse switch Side handle with depth gauge Interface for TE DRSM dust removal module Supply cord
1. General information
1.1 Safety notices and their meaning
DANGER
Draws attention to imminent danger that could lead to serious bodily injury or fatality.
WARNING
Draws attention to a potentially dangerous situation that could lead to serious personal injury or fatality.
CAUTION
Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage to the equipment or other property.
NOTE
Draws attention to an instruction or other useful information.
1.2 Explanation of the pictograms and other information
Warning signs
General warning
Warning: electricity
1
Obligation signs
Wear eye
en
protection
Wear breathing protection
Symbols
Read the
operating
instructions
before use
Chiseling Chisel position
2. Description
Wear a hard
hat
Return waste
material for
recycling.
adjustment
Wear ear
protection
Drilling without
hammering
Volts Amps
Wear
protective
gloves
Hammer
drilling
Alternating
current
Diameter Double
Hertz Rated speed
insulated
under no load
Reverse rotation
Revolutions
per minute
Forward rotation
Location of identification data on the power tool
The type designation can be found on the type iden­tification plate and the serial number on the side of the motor housing. Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department.
Type:
Serial no.:
2.1 Use of the product as directed
The power tool is an electrically-powered rotary hammer with pneumatic hammering mechanism. The power tools are designed for drilling in concrete, masonry, gypsum board (drywall), wood, plastic and metal. The power tool can also be used for light chiseling work on masonry and surface finishing on concrete. Working on materials hazardous to the health (e.g. asbestos) is not permissible. The power tool is designed for professional use. The power tool may be operated, serviced and repaired only by authorized, trained personnel. This personnel must be informed of any special hazards that may be encountered. The power tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed. The working environment may be as follows: construction site, workshop, renovation, conversion or new construction. The power tool may be operated only when connected to a power supply providing a voltage and frequency in compliance with the information given on its type identification plate. Changes or modifications to the power tool are not permissible. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance.
2
2.2 Chucks
TEC CLICK chuck
2.3 Switches
Speed control switch for smooth starting. Function selector switch: Drilling without hammering Hammer drilling Chisel adjustment (18 positions) Chiseling
2.4 Grips
Vibration-absorbing, pivotable side handle with depth gauge Vibration-absorbing grip
2.5 Protective feature
Mechanical slip clutch
2.6 Lubrication
Oil lubrication
2.7 Items supplied as standard
1 Power tool 1TE‑C CLICK chuck 1 Side handle with depth gauge 1 Operating instructions 1 Hilti toolbox 1 Cleaning cloth 1 Grease
en
2.8 Using extension cords
Use only extension cords of a type approved for the application and with conductors of adequate cross section. The power tool may otherwise loose performance and the extension cord may overheat. Check the extension cord for damage at regular intervals. Replace damaged extension cords.
Recommended minimum conductor cross section and max. cable lengths
Conductor cross sec­tion
Mains voltage 100V 50 m Mains voltage 110-
120 V Mains voltage 220-
240 V
Do not use extension cords with 1.25 mm² or 16 AWG conductor cross sections.
1.5 mm² 2.5 mm² 3.5 mm² 14 AWG 12 AWG
30 m 50 m
75 m 100 m
100 ft 150 ft
3
2.9 Using extension cords outdoors
When working outdoors, use only extension cords that are approved and correspondingly marked for this application.
2.10 Using a generator or transformer
en
This power tool may be powered by a generator or transformer which fulfills the following conditions: The unit must provide a power output in watts of at least twice the value printed on the rating plate on the power tool. The operating voltage must remain within +5% and -15% of the rated voltage at all times, frequency must be in the 50 – 60 Hz range and never above 65 Hz, and the unit must be equipped with automatic voltage regulation and starting boost. Never operate other power tools or appliances from the generator or transformer at the same time. Switching other power tools or appliances on and off may cause undervoltage and / or overvoltage peaks, resulting in damage to the power tool.
3. Insert tools, accessories
Designation Description
Chucks TEC CLICK Hammer drill bits Ø 5…28 mm Forming and installation drill bits Ø 5…20 mm Lightweight percussion core bits Ø 25…68 mm Multipurpose hole saws Ø 25…82 mm, hexagonal Pointed chisel Flat chisel Shaped chisels C-type connection end Anchor-setting tools Quick-release chuck for wood and metal drill bits Key-type chuck With smooth or hex. shank Wood drill bits Ø 3…20 mm Metal drill bits Ø Max. 13 mm Metal drill bits / stepped drill bits Ø 5…22 mm
C-type connection end C-type connection end
C-type connection end For smooth or hex. shank
Designation Description
Dust module Angular chuck
TE DRS-M C-type connection end
4. Technical data
Right of technical changes reserved.
NOTE
The power tool is available in various voltage ratings. Please refer to the power tool’s type identification plate for details of its rated voltage and rated input power.
4
Power tool TE 7C
Rated voltage 120 V Rated current input 6.3 A Mains frequency Weight of the tool, including side handle Dimensions (L x W x H) 341 mm x 86 mm x 217 mm Drilling speed without hammering 0…900/min Hammer drilling speed 740/min Single impact energy
Other information about the power tool
Chuck TEC Click Drilling performance in medium-hard concrete Protection class Protection class I (grounded) or protection class II
60 Hz
3.5 kg
2.6 J
Ø 16 mm: 56 cm³/min
(double insulated). See type identification plate.
5. Safety instructions
NOTE
contain all general safety rules for power tools which, in accordance with the applicable standards, require to be listed in the operating instructions. Accordingly, some of the rules listed may not be relevant to this tool.
5.1 General Power Tool Safety Warnings
a)
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
5.1.1 Work area safety
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you to lose control.
5.1.2 Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and refrigerators. There is anincreased riskof electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
en
5
5.1.3 Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not use a power tool while you are tired or under
en
the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the offposition before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
5.1.4 Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool before making any adjustments, changing ac­cessories, or storing power tools. Such prevent-
ive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak­ing into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
5.1.5 Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement parts. This will ensure that thesafety of the power
tool is maintained.
5.2 Hammer safety warnings
a) Wear ear protectors. Exposure to noise can cause
hearing loss.
b) Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
c) Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool "live" and could give the operator an electricshock.
5.3 Additional safety precautions
5.3.1 Personal safety
a) Always hold the power tool securely with both
hands on the grips provided. Keep the grips dry, clean and free from oil and grease.
b) Breathing protection must be worn if the power
tool is used without a dust removal system for work that creates dust.
c) Improve the blood circulation in your fingers by
relaxing your hands and exercising your fingers during breaks between working.
d) Avoid touching rotating parts. Switch the power
tool on only after bringing it into position at the
6
workpiece. Touching rotating parts, especially rotating insert tools, may lead to injury.
e) Always lead the supply cord and extension cord
away from the power tool to the rear while working. This helps to avoid tripping over the
cord while working.
f) Children must be instructed not to play with the
power tool.
g) The power tool is not intended for use by chil-
dren, by debilitated persons or those who have received no instruction or training.
h) WARNING: Some dust created by grinding,
sanding, cutting and drilling contains chem­icals known to cause cancer, birth defects, infertility or other reproductive harm; or seri­ous and permanent respiratory or other injury.
Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks, concrete and other masonry products and natural stone, arsenic and chromium from chemically­treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.To reduce exposure to these chemicals,
the operator and bystanders should work in a well-ventilated area, work with approved safety equipment, such as respiratory protection ap­propriate for the type of dust generated, and designed to filter out microscopic particles and direct dust away from the face and body. Avoid prolonged contact with dust. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth,
eyes, or to remain on your skin may promote absorption of harmful chemicals.
5.3.2 Power tool use and care
a) Secure the workpiece. Use clamps or a vice
to secure the workpiece. The workpiece is thus
held more securely than by hand and both hands remain free to operate the power tool.
b) Check that the insert tools used are compatible
with the chuck system and that they are secured in the chuck correctly.
c) Switch the power tool off and unplug the supply
cord in the event of a power failure or inter­ruption in the electric supply. This will prevent
accidental restarting when the electric power re­turns.
5.3.3 Electrical safety
a) Before beginning work, check the working area
(e.g. using a metal detector) to ensure that no concealed electric cables or gas and water pipes are present. External metal parts of the
power tool may become live, for example, when an electric cable is damaged accidentally. This presents a serious risk of electric shock.
b) Check the power tool’s supply cord at regular
intervals and have it replaced by a qualified specialist if found to be damaged. If the power tool’s supply cord is damaged it must be re­placed with a specially-prepared supply cord available from Hilti Customer Service. Check extension cords at regular intervals and replace them if found to be damaged. Do not touch the supply cord or extension cord if it is damaged while working. Disconnect the supply cord plug from the power outlet. Damaged supply cords or
extension cords present a risk of electric shock.
c) Dirty or dusty power tools which have been
used frequently for work on conductive mater­ials should be checked at regular intervals at a Hilti Service Center. Under unfavorable cir-
cumstances, dampness or dust adhering to the surface of the power tool, especially dust from conductive materials, may present a risk of elec­tric shock.
d) When working outdoors with an electric tool
check to ensure that the tool is connected to the electric supply by way of a ground fault circuit interrupter (GFCI) with a rating of max. 30 mA (tripping current). Use of a ground fault circuit
interrupter reduces the risk of electric shock.
e) Use of a ground fault circuit interrupter (GFCI)
with a maximum tripping current of 30 mA is recommended.
5.3.4 Work area safety
a) Ensure that the workplace is well lit. b) Ensure that the workplace is well ventilated.
Exposure to dust at a poorly ventilated workplace may result in damage to the health.
en
7
c) If the work involves breaking right through, take
the appropriate safety measures at the opposite side. Parts breaking away could fall out and / or
fall down and injure other persons.
5.3.5 Personal protective equipment
en
The user and any other persons in the vicinity must wear ANSI Z87.1-approved eye protection, a hard
6. Before use
6.1 Fitting the side handle 2
CAUTION
Remove the depth gauge from the side handle in order to avoid injury.
1. Disconnect the supply cord plug from the power
outlet.
2. Release the side handle clampingband byturning
the handle counterclockwise.
hat, ear protection, protective gloves and breathing protection while the machine is in use.
3. Slide the side handle clamping band over the chuck and onto the cylindrical section at the front end of the power tool.
4. Pivot the side handle into the desired position.
5. CAUTION Check that the clamping band is en-
gaged in the groove provided on the power tool.
Secure the side handle by turning the grip clock­wise.
6.2 Use of extension cords and generators or transformers
Please refer to the “Description” section.
7. Operation
CAUTION
In the event of the drill bit sticking, the power tool will pivot about its own axis. Always use the power tool with the side handle fitted and hold it securely with both hands so that the resulting opposing force causes the slip clutch to release in the event of the drill bit sticking. Use clamps or a vice to hold the workpiece securely.
8
7.1 Preparing for use
7.1.1 Adjusting the depth gauge 3
1. Release the side handle clampingband byturning the handle counterclockwise.
2. Pivot the side handle into the desired position.
3. Adjust the depth gauge to the desired drilling depth.
4. Tighten the side handle securely by turning the grip section. This also clamps the depth gauge in position.
7.1.2 Fitting the insert tool 4
CAUTION
Wear protective gloves when changing the insert tool.
1. Disconnect the supply cord plug from the power outlet.
2. Check that the connection end of the insert tool is clean and lightly greased. Clean it and grease it if necessary.
3. Check that the sealing lip of the dust shield is clean and in good condition. Clean the dust shield if necessary or replace it if the sealing lip is found to be damaged (please refer to the “Care and maintenance” section).
4. Push the insert tool into the chuck and rotate it while applying slight pressure until it engages in the guide grooves.
5. Push the insert tool further into the chuck until it is heard to engage.
6. Check that the insert tool has engaged correctly by pulling it.
7.1.5 Fitting the chuck 7
CAUTION
Remove the depth gauge from the side handle and the insert tool from the chuck in order to avoid injury.
NOTE
Set the selector switch to the “Chiseling” position before removing the chuck.
1. Disconnect the supply cord plug from the power outlet.
2. Grip the chuck sleeve, pull it forward and hold it securely in this position.
3. Slide the chuck onto the guide tube from the front and then release the sleeve.
4. Rotate the chuck until it is heard to engage.
7.2 Operation
en
7.1.3 Removing the insert tool 5
CAUTION
Wear protective gloves when changing insert tools as the insert tool will get hot during use.
1. Disconnect the supply cord plug from the power outlet.
2. Open the chuck by pulling back the chuck release sleeve.
3. Pull the insert tool out of the chuck.
7.1.4 Removing the chuck 6
CAUTION
Remove the depth gauge from the side handle and the insert tool from the chuck in order to avoid injury.
NOTE
Set the selector switch to the “Chiseling” position before removing the chuck.
1. Disconnect the supply cord plug from the power outlet.
2. Pull the chuck sleeve forward and hold it se­curely.
3. Remove the chuck by pulling it away from the power tool.
CAUTION
Working on the material may cause it to splinter.
Wear eye protection and protective gloves. Wear breathing protection if no dust removal system is used. Splintering material presents a risk of injury to
the eyes and body.
CAUTION
The work generates noise. Wear ear protectors. Exposure to noise can cause hearing loss.
7.2.1 Working at low temperatures
NOTE
The hammering mechanism works only when the power tool has reached a minimum operating tem­perature.
Bring the drill bit briefly into contact with the base material while allowing the power tool to run under no load until the minimum operating temperature is reached. If necessary, repeat this procedure until the hammering mechanism begins to operate.
9
7.2.2 Drilling without hammering 8
1. Turn the function selector switch until it engages in the “Drilling without hammering” position. Do not operate the function selector switch while
en
the motor is running.
2. Bring the side handle into the desired position and check that it is fitted correctly and secured.
3. Plug the supply cord into the power outlet.
4. Position the power tool and drill bit at the point where the hole is to be drilled.
5. Press the control switch slowly (drill at a low speed until the drill bit centers itself in the hole).
6. Press the control switch fully to continue drilling with full power.
7. Adjust the pressure applied to the power tool according to the material you are working on. This will ensure the optimum rate of drilling progress.
7.2.3 Hammer drilling 8
1. Turn the function selector switch until it engages in the “Hammer drilling” position. Do not operate the function selector switch while the motor is running.
2. Bring the side handle into the desired position and check that it is fitted correctly and secured.
3. Plug the supply cord into the power outlet.
4. Position the power tool and drill bit at the point where the hole is to be drilled.
5. Press the control switch slowly (drill at a low speed until the drill bit centers itself in the hole).
6. Press the control switch fully to continue drilling with full power.
7. Do not apply excessive pressure. This will not increase the power tool’s hammering perform­ance. Lower pressure extends the life of the insert tool.
8. Reduce drilling speed shortly before breaking through in order to avoid spalling.
7.2.4 Chiseling
NOTE
The chisel can be adjusted to 18 different positions (in 20° increments). This ensures that flat chisels and shaped chisels can always be set to the optimum working position.
7.2.4.1 Chisel position adjustment
CAUTION
Do not work operate the power tool when the selector switch is set to “Chisel adjustment”.
1. Turn the function selector switch until it engages in the “Chisel adjustment” position. Do not oper­ate the function selector switch while the motor is running.
2. Bring the side handle into the desired position and check that it is fitted correctly and secured.
3. Rotate the chisel to the desired position.
7.2.4.2 Locking the chisel
Turn the function selector switch until it engages in the “Chiseling” position. Do not operate the function selector switch while the motor is running.
7.2.4.3 Chiseling 8
1. Plug the supply cord into the power outlet. NOTE Donot operate thefunction selector switch while the motor is running.
2. Position the tip of the chisel at the point where chiseling is to begin.
3. Press the control switch.
7.2.5 Forward / reverse 9
CAUTION
Do not operate the forward / reverse switch while the motor is running.
Move the forward/reverse switch to the “Forward” or “Reverse” position.
8. Care and maintenance
CAUTION Disconnect the mains plug from the power outlet.
8.1 Care of insert tools
Clean off dirt and dust deposits adhering to the insert tools and protect them from corrosion by wiping the insert tools from time to time with an oil-soaked rag.
10
8.2 Care of the power tool
CAUTION Keep the power tool, especially its grip surfaces, clean and free from oil and grease. Do not use cleaning agents which contain silicone.
The outer casing of the power tool is made from impact-resistant plastic.Sections of the grip are made from a synthetic rubber material. Never operate the power tool when the ventilation slots are blocked. Clean the ventilation slots carefully using a dry brush. Do not permit foreign objects to enter the interior of the power tool. Clean the outside of the power tool at regular intervals with a slightly damp cloth. Do not use a spray, steam pressure cleaning equipment or running water for cleaning. This may negatively affect the electrical safety of the power tool.
8.3 Cleaning or replacing the dust shield
Clean the dust shield on the chuck with a dry, clean cloth at regular intervals. Clean the sealing lip by wiping it carefully and then grease it again lightly with Hilti grease. It is essential that the dust shield is replaced if the sealing lip is found to be damaged. Push the tip of a screwdriver under the edge of the dust shield and prise it out toward the front. Clean
the area of the chuck in contact with dust shield and then fit a new dust shield. Press it in firmly until it engages.
8.4 Maintenance
WARNING Repairs to the electrical section of the power tool may be carried out only by trained electrical spe­cialists.
Check all external parts of the power tool for damage at regular intervals and check that all controls operate faultlessly. Do not operate the power tool if parts are damaged or when the controls do not function faultlessly. If necessary, the power tool should be repaired by Hilti Service.
8.5 Checking the power tool after care and maintenance
After carrying out care and maintenance work on the power tool, check that all protective and safety devices are fitted and that they function faultlessly.
9. Troubleshooting
Fault Possible cause Remedy
The power tool doesn’t start.
No hammering action. The power tool is too cold. Allow the power tool to warm up to
Interruption in the electric supply. Plug in another electric appliance
and check whether it works.
Supply cord or plug defective.
Other electrical fault.
The carbon brushes are worn. Have the supply cord and plug
The function selector switch is set to “Drilling without hammering”.
The forward/reverse switch is set to reverse rotation.
Have the supply cord and plug checked by a trained electrical spe­cialist and replaced if necessary.
Have it checked by a trained elec­trical specialist.
checked by a trained electrical spe­cialist and replaced if necessary.
the minimum operating temperat­ure. See section: 7.2.1 Working at low temperatures
Set the function selector switch to “Hammer drilling”.
Set the forward/reverse switch to forward rotation.
en
11
Fault Possible cause Remedy
The power tool doesn’t achieve full power.
en
The drill bit doesn’t rotate.
The drill bit can’t be released.
The drill bit makes no pro­gress.
The extension cord’s conductor cross section is inadequate.
The control switch is not pressed fully.
The function selector switch is not engaged or is in the “Chiseling” or “Chisel adjustment” position.
The chuck is not pulled back fully. Pull the chuck back as far as it will
The forward/reverse switch is set to reverse rotation.
Use an extension cord with an ad­equate conductor cross section. (Please refer to the “Description” section.)
Press the control switch as far as it will go.
When the motor has stopped, turn the function control switch to the “Drilling without hammering” or “Hammer drilling” position.
go and remove the insert tool. Set the forward/reverse switch to
forward rotation.
10. Disposal
Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information.
11. Manufacturer’s warranty - tools
Hilti warrants that the tool supplied is free of defects in material and workmanship. This warranty is valid so long as the tool is operated and handled correctly, cleaned and serviced properly and in accordance with the Hilti Operating Instructions, and the technical system is maintained. This means that only original Hilti consumables, components and spare parts may be used in the tool.
This warranty provides the free-of-charge repair or replacement of defective parts only over the entire lifespan of the tool. Parts requiring repair or replace­ment as a result of normal wear and tear are not covered by this warranty.
12
Additional claims areexcluded, unlessstringent na­tional rules prohibit such exclusion. In particular, Hilti is not obligated for direct, indirect, incidental or consequential damages, losses or expenses in connection with, or by reason of, the use of, or inability to use the tool for any purpose. Implied warranties of merchantability or fitness for a par­ticular purpose are specifically excluded.
For repair or replacement, send the tool or related parts immediately upon discovery of the defect to the address of the local Hilti marketing organization provided.
This constitutes Hilti’s entire obligation with regard to warranty and supersedes all prior or contempor­aneous comments and oral or written agreements concerning warranties.
Hilti Corporation
LI-9494 Schaan Tel.:+423 / 2342111 Fax:+423/ 2342965 www.hilti.com
Hilti = registered trademark of Hilti Corp., Schaan W 3090 0406 00-Pos. 3 1 Printed in China © 2006 Right of technical and programme changes reserved S. E.& O.
202931 / A
*202931*
202931
Loading...