Hilti SF 2-A Operating Instructions Manual
SF 2-A /
SFD 2-A
Operating instructions en
Mode d’emploi fr
Manual de instrucciones es
Manual de instruções pt
Printed: 24.03.2014 | Doc-Nr: PUB / 5174908 / 000 / 00
௹ ௺
ః
ం
ఁ
ఀ
1
This Product is Certied
Ce produit est homologué
Producto homologado por
Este produto está registrado
C US
Printed: 24.03.2014 | Doc-Nr: PUB / 5174908 / 000 / 00
2
3
/
5
4
5
76
Printed: 24.03.2014 | Doc-Nr: PUB / 5174908 / 000 / 00
en
1
ORIGINAL OPERATING INSTRUCTIONS
SF 2-A/SFD 2-A cordless drill /
driver
It is essential that the operating instructions are read before the power tool
is operated for the first time.
Always keep these operating instructions together with the power tool.
Ensure that the operating instructions are with the power tool when it is
given to other persons.
Contents
1 Generalinformation ........................... 2
2 Description ................................. 4
3 Inserttools,accessories ........................ 5
4 Technicaldata ............................... 6
5 Safetyinstructions ............................ 7
6 Beforeuse................................. 13
7 Operation ................................. 15
8 Careandmaintenance......................... 17
9 Troubleshooting ............................. 19
10 Disposal .................................. 20
11 Manufacturer’swarranty-tools................... 21
1 These numbers refer to the corresponding illustrations. The illustrations
canbefoundonthefold-outcoverpages. Keepthesepagesopenwhile
studying the operating instructions.
In these operating instructions, the designation “power tool” always refers
to the SF 2-A or SFD 2-A cordless drill / driver, with battery fitted.
Parts, operating controls and indicators
1
@ Keyless chuck (SF 2-A)
; Torque and drilling mode setting ring
= Gear selector switch
% Hex. socket with locking sleeve (SFD 2-A)
& Forward / reverse switch
Printed: 24.03.2014 | Doc-Nr: PUB / 5174908 / 000 / 00
en
2
( Grip
) Lamp
+ Belt hook (optional)
§ Charging status indicator
/ Release button
: Control switch (with electronic speed control)
1 General information
1.1 Safety notices and their meaning
DANGER
Draws attention to imminent danger that will lead to serious bodily injury or
fatality.
WARNING
Draws attention to a potentially dangerous situation that could lead to
serious personal injury or fatality.
CAUTION
Draws attention to a potentially dangerous situation that could lead to slight
personal injury or damage to the equipment or other property.
NOTE
Draws attention to an instruction or other useful information.
1.2 Explanation of the pictograms and other information
Warning signs
General warning Warning: electricity Warning: caustic
substances
Printed: 24.03.2014 | Doc-Nr: PUB / 5174908 / 000 / 00
en
3
Obligation signs
Wear eye protection Wear a hard hat Wear ear protection Wear protective
gloves
Wear breathing
protection
Symbols
Read the operating
instructions before
use
Volts Direct current Rated speed under
no load
Revolutions per
minute
Drilling without
hammering
Return waste
material for
recycling.
Location of identification data on the power tool
The type designation can be found on the type identification plate at the
base of the power tool and the serial number on the side of the casing.
Make a note of this data in your operating instructions and always refer to it
when making an enquiry to your Hilti representative or service department.
Type:
Generation: 01
Serial no.:
Printed: 24.03.2014 | Doc-Nr: PUB / 5174908 / 000 / 00
en
4
2 Description
2.1 Use of the product as directed
The SF 2A and SFD 2A are hand-held cordless drill / drivers for driving
and removing screws and drilling in steel, wood and plastic.
Working on materials hazardous to the health (e.g. asbestos) is not
permissible.
Do not use the battery as a power source for other unspecified appliances.
Modification of the power tool or tampering with its parts is not permissible.
To avoid the risk of injury, use only genuine Hilti accessories and insert tools.
Observe the information printed in the operating instructions concerning
operation, care and maintenance.
The power tool is designed for professional use and may be operated,
serviced and maintained only by trained, authorized personnel. This
personnel must be informed of any special hazards that may be encountered.
The power tool and its ancillary equipment may present hazards when used
incorrectly by untrained personnel or when used not as directed.
The working environment may be as follows: construction site, workshop,
renovation, conversion or new construction.
2.2 Chuck
The SF 2-A has a keyless chuck and the SFD 2-A features a hex. socket drive.
2.3 Switches
Control switch with electronic speed control
Gear selector switch
Forward / reverse selector switch with transport lock
Torque and drilling mode setting ring
2.4 Grips
Vibration-absorbing grip
2.5 The items supplied include (toolbox versions):
1 Power tool
1 Operating instructions
1 Hilti toolbox
Printed: 24.03.2014 | Doc-Nr: PUB / 5174908 / 000 / 00
en
5
2.6 The items supplied include (cardboard box versions):
1 Power tool
1 Operating instructions
2.7 Additional items required for operating the tool:
B 12/2.6 Li-Ion battery and C4⁄1250 charger.
2.8 Liion battery charge status display
LEDs light constantly LEDs blink Charge status C
LED1,2,3,4 - C≧75%
LED1,2,3 - 50 % ≦ C < 75 %
LED 1, 2 - 25 % ≦ C < 50 %
LED 1 - 10 % ≦ C < 25 %
- LED 1 C<10%
2.9 Overload and overheating protection
The power tool is equipped with an electronic protection system to prevent
overloading and overheating. The power tool switches itself off automatically
in the event of overloading and overheating. After releasing the control
switch, the power tool may not restart immediately when the switch is
pressed again (while the power tool is cooling down).
NOTE
Overloading or overheating are not indicated by the LEDs on the battery.
3 Insert tools, accessories
Designation Short designation
Charger for Li-ion batteries C 4/12-50
Battery B12/2.6LiIon
Belt hook (optional)
Designation Description
Keyless chuck clamping range ∅ 0.8…10 mm (0.03…0.39")
Drilling diameter range in wood
(soft)
∅ 0.8…14 mm (0.03…0.55")
Printed: 24.03.2014 | Doc-Nr: PUB / 5174908 / 000 / 00
Loading...