Hikvision RS-485 User Manual
Appearance
Dimension(L*W*H)
161mm*105mm*28mm
RS-485 Wireless Receiver
Indicator and Function Button
DIP Address Settings
The DIP address and associated zone No. for different
control panels are shown below：
Network Security Control Panel Bus Security Control Panel
RS-485 Wireless Receiver
Quick Start Guide
2
Status Indicator
Adding or Deleting: Red and
green alternately flashes every
second.
Operation Finished: flashing green
Operation Failed: flashing red
Working:
Working Properly: solid green
Exception(RS-485 disconnected):
solid red
Power Indicator
Solid green after power on
RS-485 Terminal
The power of wireless receiver is supplied by control panel on the model of DS-19A08-BN, DS-19A08-BNG, and
DS-19A08-DNG. The power supply of the control panel is made by Channel Well Technology Co.,Ltd., and meets LPS.
1 2 3
Quick Operation
1
Receiver Wiring
Wire the receiver according to the diagram.
RS-485 Terminal
Power Terminal
Security Control Panel
D
+ +
D G12V
-
DIP Switch
Power Terminal
Add.9->Zone 9-16
Add.10->Zone 17-24
Add.11->Zone 25-32
Add.12->Zone 33-40
Add.13->Zone 41-48
For control panel supports 16
zones, the receiver address
starts from 10.
Add.9->Zone 9-16
Add.10->Zone 17-24
Add.11->Zone 25-32
Add.12->Zone 33-40
Add.13->Zone 41-48
Add.14->Zone 49-56
Add.15->Zone 57-64
Add.16->Zone 65-72
When the switch is towards ON, the binary value is 1. If
you set the DIP switch like the figure displayed below, its
binary value is 00010, and its decimal value is 2.
1 2 3 4 5
Specification
RF Frequency
RF Modulation
Transmission Speed
RF Transmission Distance
Power Supply
RS-485 Interface
DIP Switch
Tamper-proof
Indicator
Material
Operation Environment
Temperature
Humidity
433MHz
2GFSK
10.0kbps
400m
12 VDC
1
5 bits (address 0 to 31)
2(front/rear panel)
2, power and status
PC+ABS
Indoor
-10℃ to +55℃
10% to 90%
RS-485 Terminal
Power Terminal
Installation
Wall Mounting
RS-485 Wireless Receiver
4 5 6
UD10719B
Quick Operation
2
Add/Deletethe wireless detector to the control panel via
keypad programming.
Only the installer and administrator can add/delete the
wireless detector.
Add Detector to the Control Panel
1. Insert the following command to make the control panel
enter the adding mode. The zone No. should be 3digits, enter
0 on the high-order posion for deficiency, e.g. ,enter
023 if the zone No. is 23.
[Password]+[*]+[95]+[Zone No.]+[#]
2. Trigger the detector to add the detector to the control
panel.
3. Insert the following command to make the control panel
exit the adding mode.
[*]+[#]
At most 8 wireless devices can be connected to a wireless
receiver.
3
Install ReceiverAdd/Delete Wireless Detector
1. Install the rear panel.
Secure the rear panel on the wall with 5 screws.
2. Fix the PCB board on the rear panel.
3. Route the cables.
4. Fix the front panel on the rear panel by
ghtening the set screw.
87 9 10
Dimension
Installation
Front Panel
PCB Board
Screws
Wall
Rear Panel
Quick Operation
Delete Detector to the Control Panel
1. Insert the following command to make the control panel
enter the deleng mode.
[Password]+[*]+[96]+[#]
2. Trigger the detector to delete the detector to the control
panel.
3. Insert the following command to make the control panel
exit the deleng mode.
[*]+[#]
You can add/delete keypad via programming. For details, refer
to Security Control Panel Programming Guide.
You can also add/delete the detector via client soware.
For details, refer to Security Control Panel Programming
Guide.
11
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology
Co., Ltd.
ALL RIGHTS RESERVED.
Any and all informaon, including, among others,
wordings, pictures, graphs are the properes of Hangzhou
Hikvision Digital Technology Co., Ltd. or its subsidiaries
(hereinaer referred to be “Hikvision”). This user manual
(hereinaer referred to be “the Manual”) cannot be
reproduced, changed, translated, or distributed, parally
or wholly, by any means, without the prior wrien
permission of Hikvision. Unless otherwise spulated,
Hikvision does not make any warranes, guarantees or
representaons, express or implied, regarding to the
Manual.
About this Manual
This Manual is applicable to Control Panel
The Manual includes instrucons for using and managing
the product. Pictures, charts, images and all other
informaon hereinaer are for descripon and explanaon
only. The informaon contained in the Manual is subject to
change, without noce, due to firmware updates or other
reasons. Please find the latest version in the company
website (hp://overseas.hikvision.com/en/).
Please use this user manual under the guidance of
professionals.
12 13
Trademarks Acknowledgement and other
Hikvision’s trademarks and logos are the properes of
Hikvision in various jurisdicons. Other trademarks and
logos menoned below are the properes of their
respecve owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE
LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH
ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY
QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR
AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,
INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
DATA OR DOCUMENTATION, IN CONNECTION WITH THE
USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE
USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR
ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER
DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK,
VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL
SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK
ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING
THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE
CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE
LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH
ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL
AND THE APPLICABLE LAW, THE LATER PREVAILS.
This product and - if applicable - the supplied accessories too
are marked with "CE" and comply therefore with the
applicable harmonized European standards listed under the
RE Direcve 2014/53/EU, the EMC Direcve 2014/30/EU, the
LVD Direcve 2014/35/EU, the RoHS Direcve 2011/65/EU.
Loading...