HIKVISION DS-9100HDI-S Quick Start Manual
USA, Inc.
A Division of Hikvision China
USA, Inc.
A Division of Hikvision China
First Choice For Security Professionals First Choice For Security Professionals
www.hikvision-usa.comwww.hikvision-usa.com
www.hikvision-usa.comwww.hikvision-usa.com
USA, Inc.
A Division of Hikvision China
USA, Inc.
A Division of Hikvision China
First Choice For Security Professionals First Choice For Security Professionals
Check that your package includes the following:
Front Panel Description:
To startup your DVR:
Quick Start
NOTE: Connect VGA monitor and mouse before starting.
1. Overview
2. Connection
3. Start Up/Shutdown
4. Formatting a Disk
5. Setting Date & Time
6. Recording
7. Playback
8. Backup
1. Overview 2. Connection
3. Startup and Shutdown
Series 4 DVR Mouse IR Remote Power Cord Screws
Hard Drive (PreInstalled)
1. Power Button
2. IR Receiver
3. USB Ports
4. Status Indicators
5. Alphanumeric Buttons
6. Control Buttons
7. Direction/Enter Button
8. Jog Shuttle Control
HDD Cables Rack Mount Ears Quick Start Guide Manual/Software CD
To setup quick recording schedule:
6. Recording
Startup and Shutdown (cont.)
Internet
Router
Ethernet
PC
VGA Monitor Main Monitor Aux/Spot Monitor
Speaker
PC
Alarm
Output
Alarm
Input
Audio Input USB Device
USB Mouse IR Remote
Analog Camera
Analog Dome
Keyboard
To shutdown your DVR:
1. Plug power cord into DVR and electrical outlet. It is HIGHLY recommended to use a surge
protector. The Power indicator LED on the front panel will turn red.
2. Connect a VGA monitor and mouse into the DVR. NOTE: Monitor and mouse needs to be
plugged in before starting.
3. Switch the POWER botton on the back rear panel. The Power indicator LED will turn blue.
The unit will begin to start.
NOTE: Default password is 12345
OPTION 1: Standard Shutdown
1. Enter the Shutdown menu by going to Main Menu > Maintenance > Shutdown.
2. Select the Shutdown button.
3. Click the Yes button.
OPTION 2: Manual Shutdown
1. Press and hold the POWER button for 3 seconds.
2. Enter the administrator's username and password
in the dialog box for authentication.
3. Click the Yes button.
NOTE: Do not press the POWER button again
when the system is shutting down.
4. Formatting a Disk
NOTE: One hard disk drive (HDD) is already installed and formatted in this DVR.
A newly installed hard disk drive (HDD) must be formatted first before it can be used with your DVR.
NOTE: Formatting the disk will erase all data on it.
To format a new disk:
1. Enter the Disk Management menu by going to Main Menu > System Configuration
> Disk Management.
2. Select a disk to format. A disk that has not been formatted will show Error Detected as its status.
If the disk is one that is newly installed, the status of the drive will show up as Non-Active and the
Reformat button will change to the Add button.
3. Click the Add button.
Formatting a Disk (cont.)
4. A confirmation message will appear on the screen.
Click the Yes button to continue formatting process.
5. A format progress bar will be shown on the menu.
After the disk has been formatted, the status of the
disk will change to Active.
6. Click the Done button to exit out of Disk Management.
1. Enter the Quick Schedule Configuration menu by
going to Main Menu > Recording Configuration
> Quick Schedule Configuration.
2. Select the camera to configure from the camera
drop down menu. If all the cameras are to be configured
with the same settings, select All Cameras from the list.
3. Check the Enable checkbox to enable the recording
schedule. If the checkbox is unchecked, the recording
schedule will be disabled.
4. Check the 24/7 checkbox if you would like to record continuously or on event for 24 hours a
day, 7 days a week. If you wish to schedule different time frames for Monday through Sunday,
leave the 24/7 checkbox unchecked and skip to step 6.
5. Select Recording Type for 24/7 recording and move on to step 8. Recording type includes
Continuous for continuous recording or On Event for recording when an event is triggered (i.e.
from detected motion).
6. Select the start and stop time for each day of the week. The start and stop time are listed
using a 24 hr cycle (i.e. 18:00 is equivalent to 6:00pm).
7. Select Recording Type for each day of the week. Recording type includes Continuous for
continuous recording or On Event for recording when an event is triggered (i.e. from detected
motion) for the selected time period.
8. Check the Enable Audio checkbox if you would like to enable audio recording along with the
video. Audio can only be recorded if an amplified audio source is connected to the DVR.
9. Select the Save button to save the schedule settings and select Exit to return to the previous
menu. Selecting the Exit button without clicking Save will quit out of the menu without saving
settings.
Note: On Event recordings are recordings that are triggered from motion detection and/or from
an external alarm See ”Configuring Alarms and Exceptions” on page 61 of the user manual.
5. Setting Date & Time
1. Enter the Time/Date menu by going to Main Menu
> System Configuration > Time/Date.
2. Enter the correct date and time.
3. Click the Save button to save the setting.
To setup date and time:
NOTE: For more detailed information, refer to the Users Manual on
the CD-ROM. You must use your PC or MAC to access the files.
1
23
4
6 8
7 5
Quick Start Guide
Quick Start Guide
DS-9100HDI-S DVR Version 2.0
Quick Start Guide
DS-9100HDI-S DVR Version 2.0
Quick Start Guide
Quick Start Guide
DS-9100HDI-S DVR Version 2.0
Quick Start Guide
DS-9100HDI-S DVR Version 2.0
USA, Inc.
A Division of Hikvision China
USA, Inc.
A Division of Hikvision China
First Choice For Security Professionals First Choice For Security Professionals
www.hikvision-usa.comwww.hikvision-usa.com
www.hikvision-usa.com
Quick Start Guide
Quick Start Guide
DS-9100HDI-S DVR Version 2.0
Quick Start Guide
DS-9100HDI-S DVR Version 2.0
USA, Inc.
A Division of Hikvision China
USA, Inc.
A Division of Hikvision China
First Choice For Security Professionals First Choice For Security Professionals
Quick Start Guide
Quick Start Guide
DS-9100HDI-S DVR Version 2.0
Quick Start Guide
DS-9100HDI-S DVR Version 2.0
8. Backup
Quick Start Guide
DS-9100HDI-S
Version 2.0
USA, Inc.
A Division of Hikvision China
565 Brea Canyon Road, Suite A
Walnut, California 91789
techsupport@hikvision-usa.com
7. Playback
Playback from Search:
1. Enter the Playback menu by going to
Main Menu > Playback.
2. Set the search parameters by selecting
cameras to search and date to search on.
3. The search results will be shown on the timeline
with blue bars designating recorded files.
4. Select file and click the Play button to begin playback.
Playback from System Log:
1. Enter the System Logs menu by going to
Main Menu > Maintenance > System Logs.
2. Select date from the Calendar to search for system
logs in.
3. Select Search Type.
4. Click the Search button.
5. A list of results with your search criteria will be displayed.
If applicable, select the video log to playback and click Play.
6. The recording will begin to play in the Playback interface.
To backup recorded files:
1. Enter the File Management menu by going to
Main Menu > System Configuration > File Management
2. Select desired parameters to search for files
to backup.
3. Select the files to backup. You may also click the Play
button to verify that these files are indeed the ones
you would like to backup. The total size of the files will
also be shown on this menu.
4. Click the Files Backup button to access the Files
Backup Menu.
5. Select device to backup to from drop-down list (USB
Flash Drive, USB HDD, DVD Writer). If backup device
is not recognized:
• Click the Refresh button.
• Reconnect device.
• Check for compatibility from vendor.
6. The total available free space will be shown. If the
free space is not sufficient, delete files from the storage
device or insert a device with more available free
space.
7. Click the Backup button to begin backup process. After
the backup has completed, click the OK button.
NOTE: For more detailed information, refer to the Users Manual on
the CD-ROM. You must use your PC or MAC to access the files.
Loading...