User Manual of Embedded Net DVS
Page １ Total 31
User Manual
of
DS-6104HCI
Net Video Server
User Manual of Embedded Net DVS
Page ２ Total 31
Index
CHAPTER 1 INTRODUCTION ................................................................................................................... 4
1.1 DS-6104HCI FUNCTIONS AND FEATURES.................................................................................................... 4
1.2 COMMON APPLICA TION ............................................................................................................................... 5
CHAPTER 2 INSTALLATION ..................................................................................................................... 6
2.1 HARDWARE INSTALLATION ......................................................................................................................... 6
2.1.1 Installation steps ................................................................................................................................ 6
2.1.2 Installation notice .............................................................................................................................. 6
2.2 PANEL DESCRIPTION .................................................................................................................................... 6
2.3 THE PIN DEFINITION OF PHYSICS INTERFACES ............................................................................................. 7
2.3.1 PIN definition of RS-232 serial interface ........................................................................................... 7
2.3.2 PIN definition of RS485 serial interface .......................................................................................... 10
2.3.3 PIN definition of Ethernet interface ................................................................................................. 10
CHAPTER 3 VIDEO SERVER SET UP ..................................................................................................... 11
3.1 PARAMETER SETUP THROUGH RS-232 SERIAL PORT ................................................................................. 11
3.1.2 Shell Commands under Hyper Terminal .......................................................................................... 14
3.2 VIDEO SERVER HDD FORMAT ................................................................................................................... 17
3.3 VIDEO SERVER RECORDING SETUP ........................................................................................................... 17
3.4 PTZ CONTROL .......................................................................................................................................... 17
3.5 REMOTE SETUP VIDEO SERVER PA RA ME TER S ............................................................................................ 18
CHAPTER 4 UPGRADE FIRMWARE ...................................................................................................... 19
4.1 USE SHELL COMMAND AND TFTP SERVER ............................................................................................... 19
4.2 USE CLIENT SOFTWARE TO UPGRADE FIRMWARE ...................................................................................... 22
CHAPTER 5 PPPOE DIALUP OPERATION ........................................................................................... 25
5.1 USING PPPOE TO ESTABLISH CONNECTION .................................................................................................. 25
5.2 CLIENT ACCESS DVS WHEN USING PPPOE ............................................................................................... 26
CHAPTER 6 FREQUENT ASK QUESTIONS .......................................................................................... 28
APPENDIX A DS-6104HCI SPECIFICATIONS......................................................................................... 29
APPENDIX B GOOD LIST ........................................................................................................................... 30
APPENDIX C CUSTOMER INFORMATION CARD ............................................................................... 31
User Manual of Embedded Net DVS
- 3 -
Thanks for purchasing the products of Hikvision. If you have any
requests or questions, please contact us immediately.
This manual is applicable to DS-6104HCI Net Video Server.
This manual may contain some technically incorrect places or
printing errors. The contents will be updated on a regular basis without
additional specific notice. The updates will be added to the new version
of this manual. We will readily improve and update the products or
procedures described in the manual.
User Manual of Embedded Net DVS
- 4 -
Chapter 1 Introduction
DS-6104HCI net video server adopts embedded Linux operation system (RTOS) and TI
DaVinci processor that is completely independent of PC platform, and efficiently improves system
performance. Firmware is burned into the FLASH, making the system more steady and reliable.
DS-6104HCI net video server has the function of compressing the video signal and audio
signal simultaneously into H.264 compression standard; transmitting the compression stream
through network; real-time video and audio preview; supporting stream protocol (RTP/RTCP,
RTSP), IE browser, bi-directional voice talk and multilingual etc.
Notes:
DS-6104HCI: 4 channels video inputs and 4 channels audio inputs. All channels
can support CIF resolution real time (25FPS for PAL or 30FPS for NTSC).
1.1 DS-6104HCI functions and features
Basic Function:
1. High speed & high compression ratio of H.264 video hardware real-time compression;
2. Multiple security level leads to high system safety;
3. Support one RS-485 interface that can be used for controlling pan-tilt-zoom and
translucent channel input.
Compression Function
1. Support four channels video (PAL/NTSC) signal, and can be real-time hardware
compressed in 25F/S (PAL) or 30F/S (NTSC) CIF resolutions independently. Video is
compressed with H.264 standard, and it supports not only variable bit rate but also
variable frame rate. When choosing video image quality, you can also limit the bit rate
of the compression code.
2. Support changeable OSD position, the date and time can be added automatically.
3. Support LOGO, the position is changeable in the video image.
Network Function
1. Support one 10M/100M Ethernet compatible in ter f ace;
2. Support TCP/IP protocols; support video, audio, alarm, voice data, serial device data
transmission through TCP/IP network; build-in WEB browser, support IE access.
3. Support pan-tilt-zoom control such as PTZ, iris and focus;
4. Support remote upgrading and maintenance;
5. RS-485 interfaces support transparent transmission mode, and remote hosts can control
serial devices through it;
User Manual of Embedded Net DVS
- 5 -
1.2 Common application
Network digital surveillance, such as ATM machine, factory and the bank etc;
Remote monitoring service for prison, nursery and school;
Intelligent gate system (dynamic record the people in and out);
Intelligent building and community;
Uncared-for system of electric power station or telecom base station;
Outdoor equipment monitoring;
Bridge, tunnel and cross road-monitor ing system;
Pipeline, warehouse monitoring;
24 hour traffic monitoring;
Remote monitoring of forest, water and river, etc
User Manual of Embedded Net DVS
- 6 -
Chapter 2 Installation
2.1 Hardware installation
2.1.1 Installation steps
1. Open packing case, and check the integrity;
2. Take out things needed during installation;
3. Connect cables needed (video signal input cable, audio signal input cable, RS485 cable
and cable for LAN);
4. Take out stabilizer power supply and power on.
2.1.2 Installation notice
Please read the following notice carefully. If you have any question, please
contact us.
Notice:
1. After Opening the packing box, please check carefully to confirm that the goods in it are
consistent with list;
2. Please read user manual carefully before installation;
3. Please power-off all related equipments before installation;
4. Please check the voltage of power supply to avoid voltage mismatch;
5. Installation environmental: Do not use it under humidity and high temperature; to keep
ventilation vent freely, avoid being walled up; keep them horizontally, avoid setting up
in the vibration surroundings.
2.2 Panel description
Front panel:
User Manual of Embedded Net DVS
- 7 -
Interface Instruction (From left to right in turn)
1. Tx/Rx indicator lamp;
2. Link indicator lamp;
3. Power supply indicator lamp;
Back panel:
Interface Instruction (From left to Right in return):
1. Power jack is connected with 12V direct current through voltage stabilizer; Please use the
stabilizer power supply correctly;
2. UTP network connector;
3. 4 external alarm input and 2 relay output;
4. Standard RS-485 serial port RJ45 socket and Standard RS-232 serial port RJ45 socket;
5. 4 channels video input and audio input;
6. One line in audio input
7. One audio output.
2.3 The pin definition of physics interfaces
2.3.1 PIN definition of RS-232 serial interface
The DVS has one RS232 standard serial interface, with RJ-45 connector. Its pin definition is
as follows (‘I’ means input, and ‘O’ means output):
User Manual of Embedded Net DVS
- 8 -
(1) When the RS232 interface of the DVS connects with the DTE equipment, one end of the
cable is the 8-pin RJ45 connector (to DVS) and the other of the cable is the DB25 female
connector (to DTE). Below is the description of the internal connection between RJ45 and DB25.
(2) 25-pin to 9-pin converter’s internal connection is like this:
User Manual of Embedded Net DVS
- 9 -
(3) If you don’t want to use 25-pin to 9-pin convertor to connect DVS and DTE through
RS232 interface, you must use RJ45-DB9 cab le. Its internal connection description is:
(4) When the RS232 interface of the DVS connects with the DCE (such as MODEM), one
end of the cable is the 8-pin RJ45 connector and the other is the DB25 male connector. Below is
the description of the internal connection between RJ45 and DB25:
User Manual of Embedded Net DVS
- 10 -
2.3.2 PIN definition of RS485 serial interface
2.3.3 PIN definition of Ethernet interface
(1) PIN definition of the direct network cable connecting DVS and HUB:
(2) PIN definition of the cross network cable connecting DVS and host PC:
User Manual of Embedded Net DVS
- 11 -
Chapter 3 Video Server Setup
There are three kinds of methods to configure the parameters of video server.
1. Through Hyper Terminal (connect DVS with the PC through RE-232 serial ports)
2. Through TELNET (connect DVS with PC through network)
3. Through client-end application software (connect DVS with PC through network)
3.1 Parameter Set u p through RS-232 serial port
Please direct connect the RS-232 serial port of PC with the RS-232 serial port of video server
before configuration (there are RJ45 head and DB9 line in the packing carton)
How to establish the connection with the super terminal connection?
Step one: Enter into Hyper Terminal. Click “Start” “Programs” “Accessories”
“Communications” “Hyper Terminal” in Windows system, and the dialogue box below will
appear (Fig. 3.1):
Fig. 3.1 Newly establish a connection and define the name and icon
Step2: To name the connection name and to define the icon. Input a name (e.g. aa), select a icon,
press “OK”, the dialogue box like Fig. 3.2 appears.
User Manual of Embedded Net DVS
- 12 -
Fig. 3.2 Select communication port
Step 3”: to select the communication port. Select “com1” communication port in Fig3.2, press
“OK”, the dialogue box as Fig. 3.3 will appear.
Fig. 3.3 Serial ports parameter setup
Step 4: Serial port parameters setup. Set the serial port parameters as the following setup: Bits per
second: 115200, Data bits: 8, Parity: None, Stop bits: 1, Flow control: None. Press “OK” after
finish, the Hyper Terminal interface like Fig. 3.4 will appear
User Manual of Embedded Net DVS
- 13 -
Fig. 3.4 Hyper Terminal Interface
Step 5: To close the window, the Fig. 3.5 will appear. Select “Yes” and Fig. 3.6 will appear:
Fig. 3.5 Disconnect
Fig. 3.6 Save Hyper Terminal session
Step 6: Save the Hyper Terminal session for using next time. After saving, it will new establish a
“Hyper Terminal” item in the program group “Start” “Programs” “Accessories”
“Communications” “Hyper Terminal” and it includes all “Connection” name for all Hyper
Terminal. Here you have see “aa.ht”.
User Manual of Embedded Net DVS
- 14 -
3.1.2 Shell Commands under Hyper Terminal
Please use the DTE cable and the DB9/DB25 convertor to connect PC with DVS RS-232
port.
Step 1: Enter into the Hyper Terminal. Click “Start” “Programs” “Accessories”
“Communications” “Hyper Terminal” “aa.ht”, the Hyper Terminal interface in Fig. 3.4 will
appear.
Step 2: Press “Enter” in Hyper Terminal, the prompt “#” appear, as in Fig. 3.7. Under this prompt
the following operation comm ands to accomplish the setup of the parameters.
Fig. 3.7 Hyper Terminal command prompt
Input help, the supported configuration commands can be checked up, as in Fig. 3.8.
User Manual of Embedded Net DVS
- 15 -
Fig. 3.8 Check command
The following is the introduction of getIp, setIp commands.
getIp
Function: get the fixed IP, subnet mask, gateway, command port, IP address of PPPoE dialup (the
IP address of PPPoE will be 0.0.0.0 if there is no dialup or dialup is not successful).
Parameter: none.
Grammar format: Enter after input the command
Explanation: Please pay attention whether the inputting letters are capital or low case.
User Manual of Embedded Net DVS
- 16 -
Fig. 3.9 Get parameters of IP, PPPoE
setIp
Function: set the IP, subnet mask and gateway of the device
Parameter: IP address, subnet mask, gateway
Grammar format: setIp IP: mask
Explanation: Please pay attention whether the inputting letters are capital or low case. And
separate the parameters by colons.
Fig. 3.10 Set IP
User Manual of Embedded Net DVS
- 17 -
3.2 Video Server HDD format
Please refer to chapter 3.1 to get video server IP address. Then use remote client software to
access video server. Please refer to client software user manual for detail information.
3.3 Video Server Recording Setup
Please use remote client software to remote setup video server local recording parameters.
3.4 PTZ control
Step1: Connect DS-6104HCI RS-485 interface with PTZ. Please refer to RS-485 pin
definition. DVS just uses Pin8 (TX+) and Pin7 (TX-) to send PTZ control command.
Step2: You can use remote client software to setup PTZ protocol.
In client software remote “Local Configure” dialog box, select “COM configuration” tab button.
You can select DVS PTZ parameters in the corresponding dialog box.
Fig. 3.11 RS-485
Please refer to client software user manual for detail information.
User Manual of Embedded Net DVS
- 18 -
3.5 Remote setup video server parameters
Before the configuration, please make sure that the PC and the video server has been
established the network connection, you can confirm using PING command. Please refer to the
user manual of DVRDVS client software for detail information.
Fig.3.12 Server Configuration
User Manual of Embedded Net DVS
- 19 -
Chapter 4 Upgrade Firmware
There are two methods to upgrade the DVS firmware. One is using shell commands to ask
DVS to download firmware from TFTP server. The other is using PC client software.
4.1 Use Shell Command and TFTP Server
Step 1:
Before the update start you should do the follow steps:
1. Download the TFTP server from the internet, such as Cisco TFTP Server. Then put the
firmware in the root directory of the Cisco TFTP Server.
2. Connect the device to the Router.
3. Please use DTE cable to connect device 232 port with COM port of the server PC.
4. Configure the Hyper Terminal. Steps as below.
Enter into start----all programs----accessories------communications-----hyper terminal. Click hyper
terminal.
1) Input the name “aa”. And do the step 1 again. Then enter into Fig 4.2. Select COM1 and click
“OK” to enter into Fig 3.
Fig 4.1 Fig 4.2
2) Modify the bits per second to ‘115200’. and modify the flow control to’ None.’ Finally click
“apply” and “ok” to enter into the hyper terminal main interface.
User Manual of Embedded Net DVS
- 20 -
Fig 4.3
Step 2:
Then reboot the device and press any button in the pc keyboard again and again until the HIK
# come out in the Hyper Terminal interface, show as Fig 4.4. Then input the “print” to check if the
IP of the server and device is correct, also both of them should be in the same LAN. you can use
the command
“set serverip” to modified the server ip
“set ipaddr” to modified the device ip
“set netmask” to modified the mask ip
Show as the Fig.4.5.
Fig 4.4
User Manual of Embedded Net DVS
- 21 -
Fig 4.5
Step 3:
Input commend “save” and press enter button. Show as Fig.4.5.
Step 4:
Input the commend “update” and press enter button, then space button. After that the update
will start. Show as Fig.4.6
Fig. 4.6
User Manual of Embedded Net DVS
- 22 -
Step 5:
After the update finished, please input the command “reset” and press the enter button. The
device will reset. Show as Fig.4.7.
Fig 4.7
4.2 Use Client Software to upgrade firmware
In the system setup dialog of DVRDVS client software (refer to client software user manual),
there is a button named “Other”:
User Manual of Embedded Net DVS
- 23 -
Fig.4.8 Remote upgrading
Click “Explore” button and select the firmware file.
Fig.4.9
Then click “Upgrade” button, to complete the upgrading process of the video server
firmware.
User Manual of Embedded Net DVS
- 24 -
Fig.4.10
User Manual of Embedded Net DVS
- 25 -
Chapter 5 PPPoE Dialup Operation
DS-6104HCI video server supports remote access through network, through browser, through
PPPoE or PPP dialup. Before using this function, please make sure that the software you used in
your device support such functions or not.
5.1 Using PPPoE to establish connection
In the local LAN, use the client software remote setup the DVS parameters. The setup dialog
is looked as following:
Fig.5.1
In the server parameters sub dialog, enable PPPoE function, input the correct PPPoE user
name and PPPoE password. Click “Confirm” button and “Save Para.” button. The new server
parameters will be saved into video server through network. Reboot the video server, the DVS will
start to dialup the internet. After success, the video server will get a dynamic WAN IP address.
User Manual of Embedded Net DVS
- 26 -
Fig.5.2
[Explanation] please make sure that ADSL Modem is installed. If it is the first time to set
PPPoE parameters, it needs to reboot video server to establish the connection.
5.2 Client access DVS when using PPPoE
There are two methods:
One is to access using the current WAN IP address of the video server.
When the video server is successful establish the network connection by using PPPoE mode,
it will get the WAN IP address. You can use Hyper Terminal to get the WAN IP address, and
access this IP address throu gh cli en t software.
The other is to access through domain analysis server. By using this mode, you need a PC
with a fixed WAN IP address in the Internet, and there is the domain analysis server software
running in this PC (actually this PC is the analysis server). We provide such demo DNS software
and SDK.
In the server parameters of video server, there is an item named DNS. Please input the PC
fixed WAN IP address here. When the video server is successfully connection with the internet by
using PPPoE, it will get a dynamic WAN IP address, and send the name and current IP address to
the analysis server. If the client-end software wants to access the video server, it’d first to
connect with the PC used as the analysis server, telling the analysis server which one video server
he wants to access. The analysis server will search all the video servers have been registered, find
out the server with the same name or same serial number, and tell the client-end the WAN IP
address of the video server. After the client-end software get the current IP address, it can establish
User Manual of Embedded Net DVS
- 27 -
the network connection with the video server to get the video images directly .
Fig.5.3
Here the fixed WAN IP address of PC is 220.184.114.48. We cal l it as DNS IP. In that the PC,
one demo analysis server software named IP Server is run. It can get the video server information,
including the dynamic WAN IP address of the video server.
Fig.5.4
User Manual of Embedded Net DVS
- 28 -
Chapter 6 Frequent ask questions
1, Failure to control PTZ
It is possible that the camera and equipment are not connected through RS485
port, or the wrong configuration of the decoder.
2,certain individual channel picture is un-normal
Please check whether the video cable is well connected with the camera and the
Embedded DVS
3,Possible reasons which can cause the failure of upgrading
Failure of the network, IP address error in the FTP host computer, FTP service is
not been booted by PC, the path to upgrade is incorrect; no permission (usually
happened when to upgrade through client-end.)
If the above information cannot meet your demand, please not hesitate to contact
the provider.
User Manual of Embedded Net DVS
- 29 -
Appendix A DS-6104HCI Specifications
Model DS-6104HCI
Video compression
H.264
Encode/Decode
resolution
4CIF/DCIF/2CIF/CIF/QCIF
Video input
4
Video input interface
BNC (1.0Vp-p, 75Ω), support PAL, NTSC
Frame rate (per
channel)
4CIF/DCIF/2CIF: 4fps for 4-ch
CIF: 25(P)/30(N) fps
Stream type
Video / Video&Audio
Support dual stream
Yes
Bit rate
32Kbps~2Mbps adaptive ( M ax. 8Mbps)
Audio input
4
Audio input interface
BNC (2Vp-p, 1kΩ)
Audio output
1 channel (linear electrical level, 600Ω)
Audio compression
OggVorbis, 16Kbps
Voice talk input
1 channel (2Vp-p, 1kΩ)
Communication
interface
1 RJ45 10M/100M Adaptive Ethernet interface, 1 RS232 interface and 1
RS485 interface
Alarm input
4 channels
Alarm output
2 channels
Power supply
12V DC
Power consumption
≤20W
Working temperature
-10℃~+55℃
Working humidity
10%~90%
Size(mm)
39mm(H)*198mm(W)*123mm(D)
Weight
≤1 Kg
Stabilizer power suppler: input AC 100-240V47-63Hz
User Manual of Embedded Net DVS
- 30 -
Appendix B Good list
1. One piece of DS- 6104HCI video server;
2. A CD contains client application;
3. One power supply voltage stabilizer
4. A 220V power cable;
5. A cable connecting RS232 with DTE;
User Manual of Embedded Net DVS
- 31 -
Appendix C Customer Information Card
User’s Name
Mr./Mrs.
Company Name
Post Address
Postcode
Phone Number
E-mail
Model Number
of Product
Serial Number
of Product
Purchase Date
Distributor
Suggestions:
Loading...