Hikvision DS-2CE56D1T-IRM-3, DS-2CE56D1T-IRM-6, DS-2CE56D1T-IRMB-2.8MM, DS-2CE56D1T-IRMB-6MM User Manual

TURBO HD

TVI Turret Camera

User Manual

UD.6L0201D1933A01

Thank you for purchasing our product. If there are a ny questions, or requests, please do not hesitate to contac t th e de al er. This manual applies to

Type

III

This manual may c on tain severa l techni cal incorrect places or printing errors, and the content is subject to change without notice. The updates w il l be a dded to th e ne w ve rsion of this manual. We will readily improve or update the products or procedures described in the manual.

Privacy Notice

Surveillance laws vary by jurisdiction. Check all relevant laws in your jurisdiction before using this product for surveillance purposes to ensure that your use of this product conforms.

Please refer to the product specification for camera parameters and functions.

0100001050409

Model

DS-2C E56D1T-IRM

DS-2C E56D1T-IT3

DS-2C E56D1T-IR

DS-2C E56D1T-IT1

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tes ted and found to co mp ly w it h th e li mits for a digital d ev ic e, p ursu ant to part 15 of the F CC Rules. These limits are designed to pro vi de reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment gen erates, uses, and can rad ia te radio frequency energy and, if not installed and used in accordance with the instruction manual, may cau se harmf ul int er feren ce t o radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be req ui re d to correct the inte rference at h is o wn expense.

FCC Conditions

This device complies with part 15 of the FC C Rules. Operation is subject to the following two conditions:

1. This device may no t ca us e ha rm fu l interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement

This prod uc t and - if applicable - the supplied accessories too are marked with "CE" and com ply therefore w it h

stand ards listed u nder the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.

upon the purchase of equivalent new equipment, or dispose of it at designated collection points.

For more information see:

See the product documentation for specific bat tery informat io n. The bat tery is ma rke d with this sy mb ol , wh ic h may in cl ud e le ttering to indicate cadmium (C d) , le ad ( Pb ), o r me rc ur y (H g) . For p roper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

the applicable harmonized European

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted

municipal waste in the European Union. For proper recycling, return this product to your local supplier

www.recyclethis.info. 2006/66/EC (battery directive):This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union.

1 Introduction

1.1 Product Features

This series of camera a do pt s ne w gene ration sensor with high sensitivity and advanced circuit design technology It features high resolution,. low image d istort io n an d lo w no is e, e tc , wh ich. makes it suitable for surveillance system and image processing system.

l High performance CMOS sensor and high

resolution bring high-quality image;

l Low illumination; l OSD menu, parameters are configurable; l Support auto white balance, auto gain control,

Support image effect adjustment;

Unit transmission control;

l Advanced 3-axis design meets different

installation requirements.

1.2 Overview

1.2.1 Over view of Type I Came ra

Side Opening

Tri m Rin g

HD Video Cable

Power Cabl e

1.2.2 Over view of Type Came ra

Enclosure

Tri m Rin g

Mounting Base

1.2.3 Overview of Type CameraIII

Mounting Base

Enclosure

Camera

HD Video Cable

Power Cabl e

Enclosure

Camera

HD Video Cable

Power Cabl e

2 Installation

Before you start:

l Please make s ure th at the d evice in t he p ac kage

is in good condition and all the assembly parts are i nc lu ded.

l Make su re that all the related e qu ipment i s

power-off during the installation.

l Check the specification of the products for the

installation environment.

l Check whether the power supply is matched

with yo ur pow er o ut pu t to avoid damage.

l Please make sure the wall is strong enough to

withsta nd t hree tim es t he weight of the camera and the mounting.

l If the wall is the cement wall, you n eed to i ns er t

exp an si on s crews befor e you install the cam era. If the wall is the wooden wall, you can use self-tapping screw to secure t he c am era.

l If the product does not function properly,

please contact your dealer or the nearest service center. Do no t di sassemble the camera for repair or maintenance by yourself.

2.1 Installation of Type CameraI

Steps:

1.Drill the screw holes according to the drill template.

Screw hole

Figure 2-1 The Drill Template

2. Scre w th e cl ip p la te onto the mounting base loosely.

Figure 2- 2 Sc rew th e Cl ip P late

3. Fix the mounting base to the ceiling with the

supplied screws.

4.Ro ute the cables to the cable hole and connect

the corre sp on ding power c ab le a nd v id eo cab le .

5.Pull out the clip plate and secure the cam era

with the trim ring to the mounting base.

6.Push the clip plate in and tighten t he l oc k scre w

to secure the trim ring.

Clip Plate

Figure 2- 3 Fi x the the Camera

6.Adjust the cam era according to the figure b el ow to get an o pt im um a ng le .

0 ~360°°

0~75°°

Figure 2-4 3-axis Adjustment

2.2 Installation of Type CameraII

Steps:

1.Drill the screw holes and the cable hole on the ceiling according to the supplied drill template.

Cable Hole

Screw Hole

Figure 2-5 The Drill Template

2.Fix the mounting base to the ceiling with the supplied screws.

Figure 2- 6 Fi x the Mounti ng Base and Camera

3.Ro ute the cables to the cable hole and connect corresponding power cable and video cable.

4.Secure t he cam era to the mounting base.

5.Fix the enclosure to c am era.

6.Attach the trim ring to the camera a nd rotate it clockwise to secure the camera loosely.

0 ~360°°

0~75°°

0 ~360°°

Figure 2-7 3-axis Adjustment

7.Adjust the camera according to the figure 2-7 to

get a n op ti mu m an gle and tighte n th e tr im r in g.

2.3 Installation of Type CameraIII

Steps:

1.Drill the screw holes and the cable hole on the ceiling according to the supplied drill template.

Cable Hole

Screw Hole

Figure 2-8 The Drill Template

2.Fix the mounting base to the ceiling with the

supplied screws.

Figure 2- 9 Fi x the Mounti ng Base and Camera

3.Ro ute the cables to the cable hole and connect

corresponding power cable and video cable.

4.Secure t he cam era to the mounting base.

Adjust the camera according to the figure below

to get an o pt im um a ng le .

0~360°°

0~75°°

0 ~360°°

Figure 2-10 3-axis Adjustment

3 Menu Operation

MODE

5 BLC 5 MIDDLE

VIDEO

SETTING

CONTRAST

SHARPNESS

SATURATION

DNR

MIRROR

MODE MWB

RESET

EXIT

R GIAN 1-|--10 B GAIN 1-|--10

RETURN 8

Figure 3-3 WB

SAVE/EXIT

DAY/NIGHT

BRIGHTNESS

EXPOSURE MODE

AGC

INFRARED

SMART IR

Figure 3-1 Main Menu

With a coaxial camera controller (purchase separately) or calling the preset No.95 you can select the menu and adjust the camera parameters.

3.1 FORMAT

You can set the for ma t as PAL/NTSC.

3.2 SET UP

Move th e cu rsor to , and pre ss m enu buttonSET UP to en ter the S E T U P sub menu.

3.2.1 AE

Move the cursor to AE, and you can adjust the image brightness by the ,BRIGHTNESS EXPOSURE MODE AGC, and .

:Brightness

Brightness re fers to the b ri ghtnes s of t he i ma ge .

Exposure Mode:

Move the cursor to , you can selectExposure Mode the exposure mode between and .Globe BLC When BLC is selected as the exposure mode, the level o f B L C mode can be adjusted, as shown in the Figure 3-2.

EXPOSURE

1.BRIGHTNESS

2.EXPOSURE MODE LEVEL

3.AGC

4.RETURN

Figure 3-2 EXPOSURE

AGC: AGC o pt im izes the cla ri ty o f im ag e in p oo r li gh t scene. AGC leve l ca n be s et a s OF F, LOW, MIDDLE and HIGH.

3.2.2 WB

Move th e cu rsor to WB, and you can s et W hi te Balance mode as and in this menuAWB MWB .

AWB: white balance is being adjusted

automatically.

: Set the value from 1 to 10.MWB R GAIN/B GAIN

As shown in Figure 3-3.

3.2.3 DAY & NIG HT

Move the cursor to DAY & NIGHT, and select

COLOR B/W SMART, , or as the DAY & NIGHT mode. COLOR: The image is colore d in d ay m od e al l th e

time.

: The image is black & white all the time, andB/W

the IR LED turns on in the low-light conditions.

: Select to turn on/off the INFRARED_LAMPSMART

and to set th e Sm art IR lev el f rom 1to 16.

As shown in Figure 3-4.

DAY/NIGHT

MODE SMART

INFRARED OFF

SMART IR 0-|--5

RETURN 8

Figure 3-4 DAY/NIGHT

3.2.4 VIDEO SETTING

Contrast:

Contrast enhances the d iffer en ce i n colo r an d li ght betwe en p ar ts of an image. You can set the value fro m 1 to .

Sharpness: Sharpness determines the amount of detail that an imaging system can reproduce. You can set the value fro m 1 to 10.

Saturation:

You can set the saturatio n level of the image. The val ue i s from 0 to 10.

DNR:

DNR decreases the noise effect, especially in low light conditions and delivers more accurate and sharp image quality. You can set t he val ue f rom 0 to 7.

:Mirror

You can set the Mirror status as H, V, H V, or O F F.

3.2.5 Reset

Res et a ll t he s ettings to the defa ul t.

3.2.6 EXIT

Exit and Save & exit are selectable.

3.2.7 SAVE/EXIT

Move th e cu rsor to , and pre ss O K toSAVE & E xi t save the settings and exit the menu.