Hikvision DS-2CE56D1T-AVFIRB, DS-2CE56D1T-AVPIR3B User Manual
TURBO HD
1080P Dome Camera
User Manual
UD.6L0201D1939A01
Thank y ou fo r pu rchas in g our pro duct. If there
are a ny ques tions, or r equests , please do n ot
hesitate t o contact the deal er.
This manual applies to
Type
Type
Type
This ma nu al may conta in several tec hnical
incorrect places or printing errors, and the
content is subject to change without notice.
The upd ates wi ll b e added to th e new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
Privacy Notice
Surveillance laws vary by jurisdiction. Check
all relevant laws in your jurisdiction before using
this product for surveillance purposes to ensure
that your use of this product conforms.
Please refer to the product specification for
camera parameters and functions.
0100001050409
DS-2CE56D1T-AVPIR3/ VPIR3
I
DS-2CE56D1T-AVFIR/VFIR
II
Model
Regulatory Information
FCC Information
FCC compliance: This equipment has been
tested and found to comply with the limits for a
digital devi ce , pursu ant to pa rt 1 5 of the FC C
Rules . Th ese limit s are desig ned to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
gen erates, uses, an d can rad iate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cau se h armful interferen ce to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
req uired to corre ct the interfe rence a t his own
expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This d evice may not caus e ha rmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - i f applica ble - the
supplied accessories too are marked
with "C E" a nd comp ly t herefore w ith
the applicable harmonized European
standard s liste d under the L ow Volta ge Dire ctive
2006/95/EC, the EMC Directive 2004/108/EC,
the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points.
For more information see:
See the product documentation for specific
bat tery in forma tion. The b atter y is marked with
this symbol, whi ch may in clude letterin g to
indic ate cadmium (Cd) , lead (Pb), or m ercur y (H g).
For p roper r ecycl ing, retu rn t he battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
this product to your local supplier
www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European
Union.
1 Introduction
1.1 Product Features
This camera adopts new generation sensor with
high sensitivity and advanced circuit board design
technology. It possesses the features of high
resolution, low distortion, and low noise, etc. It is
extremely suitable for supervisory system and
image processing system.
The main features are as follows:
l
High performance CMOS sensor and high
resolution bring high-quality image;
l
Low illumination;
l
Support IR cut filter with auto switch;
l
OSD men u, p ara meters are configurable;
l
Support auto white balance, auto gain control,
electronic shutter control and internal
synchronization;
l
SMART IR mode;
l
Unit transmission control;
l
Advanced 3-axis design meets different
installation requirements.
1.2 Overview
1.2.1 Overview of Type I Dome Camera
Black Liner
Figure 1-1 Ove rv iew of Type I Do me Camera
1.2.2 Overview of Type Dome Camera
Lens
Figure 1-2 Ove rv iew of Type Dome Ca meraII
Bubble
Lens
Back Box
II
Black Liner
Powe r Cable
HD Video Cable
Power Ca ble
HD Video Cable
Base plate
Bubble
2 Installation
Before you start:
l Pleas e make su re that t he device i n the package
is in good condition and all the assembly parts
are i ncluded.
l Make sure that all th e relat ed equipm ent is
power-off during the installation.
l Check t he s pecific ation o f th e produ ct s for t he
installation environment.
l Check w hether the po wer sup pl y is matc hed
with yo ur powe r output to avoid da mage.
l Pleas e make su re the wall is strong eno ug h to
withstand three times the weight of the camera
and the mounting.
l If the wa ll is the cem ent wal l, you need t o insert
exp ansion screws be fore you install th e camera.
If the wall is the wooden wall, you can use
self- tapping s crew to s ecure t he camera.
l If the product does not function properly,
please contact your dealer or the nearest
service c enter. Do not disass emble the cam era
for repair or maintenance by yourself.
2.1 Ceiling Mounting
Steps:
1.Dril l the screw h oles and th e cable hol e on t he
ceiling according to the supplied drill template.
Type I:
Figure 2-1 The Drill Template
.
2 Loosen the screws on the bubble of type 1
cam era /ro tat e the bubbl e of t ype2 ca me ra to
remove the bubble and the black liner.
Type I:
Figure 2-2 Remove the Bubble
Type I :I
Type I :I
3.Attac h the back box of type 1 camera / ba se plat e
of type2 camera to the ceiling and secure them
with supplied self-tapping screws.
4.Route th e cables through the c able hole .
5.Alig n the camera with th e ba ck box/ base plate,
and tig hten th e set screws to secu re the ca mera
with the back box/base plate.
Type I:
Type I :IType I :IType I :I
4.Route and connect the corresponding cables.
5.Fix the camera to the in-ceiling mount with the
supplied screws.
Type I:
Type I :I
Figure 2-6 Fix the C amera to the Mount
3 Menu Operation
MODE
VIDEO
SETTING
CONTRAST
SHARPNESS
SATURATION
DNR
MIRROR
RESET
AE
BRIGHTNESS
EXPOSURE MODE
AGC
DAY/NIGHT
WB
INFRARED
SMART IR
Figure 3-1 Main Menu
AWB: white balance is being adjusted
automatically.
: Set the val ue from 1 t o 10.MWB R GAIN/B GAIN
As show n in Figure 3 -3.
3.2.3 DAY & NIGHT
EXIT
SAVE/EXIT
Move the cursor to DAY & NIGHT, and select
COLOR B/W SMART, , or as the DAY & NIGHT mode.
COLOR: The image i s color ed in day m ode all the
time.
: The image is b lack & white all the tim e, a ndB/W
the IR LE D tu rns on in the l ow-light conditi on s.
: Select to turn on/off the INFRARED_LAMPSMART
and to set the Smart I R level f rom 1to 1 6.
As shown in Figure 3-4.
Figure 2-3 Fix the Camera to the Ceiling
6. Connect the corresponding cables.
7. Adju st the ca me ra ac cording to the figure below
to get an optimu m angle.
8. Fit th e black liner o n the camera and tig hten th e
screws on the bubble of type 1 camera or rotate the
bubble of type 2 camera to complete.
Type I:
0~75°°
T Direction
R Direction
P Direction
0 ~355°°
Type I :I
T Direction
0 ~355°°
0~75°°
0°~355°
R Direction
0 ~340°°
P Direction
Figure 2-4 3-axis Adjustment
2.2 In-ceiling Mounting
You need to purchase an in-ceiling mount separately
if you adopt in-celling mounting.
Steps:
1.Dril l the screw h oles and th e cable hol e in t he
ceiling according to the supplied drill template.
2.Screw the bolts through the mount by aligning
with th e 2 bo lt holes. F it the toggle s onto th e bo lts.
3.Pus h th e two tog gl e bolts through the two screw
holes on the ceiling. Rotate the bolt till the toggle
holds the ceiling tightly.
Figure 2-5 Install the Mo unt
6. Repeat steps 6-8 of the Ceiling Mounting section
to complete the installation.
2.3 In-ceiling Mounting
in-ceiling mounting with gang box is supported by
the bot h ty pes of ca me ra.
1.Repeat steps 2-3 of the In-ceiling Mounting
section to secure the in-ceiling mount (supplied)
to the gang box.
Figure 2-7 Install the Mo unt
2.Route and connect the corresponding cables.
3.Align t he camera with the gang box, and tig hten
the screws to secure th e camera with the gang box..
Figure 2-8 Fix the C amera to the Gang Box
5. Repeat steps 6-8 of the Ceiling Mounting section
to complete the installation.
With a coaxial camera controller (purchase
separately) or calling the preset No.95 you can
select the menu and adjust the camera parameters.
3.1 FORMAT
You can set t he format as PAL/ NTSC.
3.2 SET UP
Move the curso r to , and press menu buttonSETUP
to en ter the S ET U P sub me nu .
3.2.1 AE
Move the cursor to AE, and you can adjust the
image brightness by the ,BRIGHTNESS EXPOSURE
MODE AGC, and .
:Brightness
Brigh tness refe rs to the b rightne ss of the image.
Exposure Mode:
Move the cursor to , you can selectExposure Mode
the exposure mode between and .Globe BLC
When BLC is selected as the exposure mode, the
level of BLC mode can b e ad juste d, as shown i n the
Figure 3-2.
EXPOSURE
1.BRIGHTNESS
2.EXPOSURE MODE
LEVEL
3.AGC
4.RETURN
5
BLC
5
MIDDLE
WB
MODE MWB
R GIAN 1-|--10
B GAIN 1-|--10
RETURN 8
Figure 3-3 WB
Figure 3-2 EXPOSURE
AGC:
AGC o pt imizes the clari ty of image i n po or light
scene . AGC level can be set a s OFF, LOW, MIDD LE
and HIG H.
3.2.2 WB
Move the curso r to WB, an d you can s et White
Balance mode as and in this menuAWB MWB .
DAY/NIGHT
MODE SMART
INFRARED OFF
SMART IR 0-|--5
RETURN 8
Figure 3-4 DAY/NIGHT
3.2.4 VIDEO SETTING
Contrast:
Contrast e nhances the d ifferenc e in color an d li ght
between parts of a n image.
You can set t he value from 1 to .
10
Sharpness:
Sharpness determines the amount of
detail that an imaging system can reproduce.
You can set t he value from 1 to 10.
Saturation:
You can set t he s aturation le vel of th e im age. The
val ue is fro m 0 to 10.
DNR:
DNR decreases the noise effect, especially in low
light conditions and delivers more accurate and
sharp i ma ge qual it y. You can set t he valu e from
0 to 7.
:Mirror
You can set t he M irror stat us as H, V, H V, or O FF.
3.2.5 Reset
Res et all the se tting s to the default.
3.2.6EXIT
Exit and Save & exit are selectable.
3.2.7SAVE/EXIT
Move the curso r to , and press OK toSAVE & Ex it
save the settings and exit the men u.
Loading...