Hikvision DS-2CE56D0T-IT3 Service Manual

TURBO HD

TVI Bullet&Turret Camera

User Manual

UD.6L0201D2132A01

Thank yo u for purch asi ng ou r product. If there

are a ny questions , or requests, please do not

hesitate to co ntact the dealer.

This manual applies to

Type

Type I

Type II

In the model list, “X” indicates single or multiple

letters. For example, DS-2CE56C0T-IRX can be

DS-2CE56C0T-IRMM.

This manual may contai n several t echnical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new v ersion of

this manual. We will readily improve or update

the products or procedures described in the

manual.

0200011051130

Model

DS-2CE16C0T-ITX DS-2CE16D0T-ITX

DS-2CE56C0T-ITX

--DS 2CE56D0T ITX

Please refer to the product specification for

camera parameters and functions.

Privacy Notice

Surveillance laws vary by jurisdiction. Check all

relevant laws in your jurisdiction before using

this product for surveillance purposes to ensure

that your use of this product conforms.

Please refer to the product specification for

camera parameters and functions.

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tes ted and fou nd to comply with the limits for a

digita l device, pursuant to part 15 of the F CC

Rules. These lim its a re designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

gen erates, u ses , and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cau se ha rmf ul interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

req uired to corre ct the interference at hi s own

expense.

FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This devic e may not cause harmf ul

interference.

2. This devic e must accept any interfe rence

received, including interference that may

cause undesired operation.

EU Conformity Statement

This product and - if applicable - the

supplied accessories too are marked

with "C E" and c omply therefore with

the applicable harmonized European standards listed under the Low Voltage Directive

2006/95/EC, the EMC Directive 2004/108/EC,

the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European Union. For proper recycling, return

upon the purchase of equivalent new equipment, or dispose of it at designated collection points.

For more information see:

See the product documentation for specific

bat tery info rmation. The battery is marked wi th

this sym bol, which may incl ude l ettering to

indica te cadmium (Cd), le ad (P b), o r mercury (Hg).

For p roper recycl ing , return the battery to you r

supplier or to a designated collection point. For

more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)

standards requirements.

this product to your local supplier

www.recyclethis.info.

2006/66/EC (battery directive):

This product contains a battery that

cannot be disposed of as unsorted

municipal waste in the European

Union.

1 Introduction

1.1 Product Features

This series o f cam era adopts new g enerati on

sensor with high sensitivity and advanced circuit

design technology It features high resolution,.

low imag e distortion and low noi se, e tc , whi ch.

makes it suitable for surveillance system and

image processing system.

l High performance CMO S sensor and high

resolution bring high-quality image;

l Low illumination;

l Support auto white balance;

l Unit transmission control;

l Advanced 3-axis design meets different

installation requirements.

1.2 Overview

1.2.1 Over view of Type I Ca mera

Power Ca ble

Mounting Base

HD Video Cable

Sun Shield

Lens

Figure 1 -1 Overview of Type I Camera

1.2.2 Over view of Type Ca mera

Mounting Base

Figure 1 -2 Overview of Type II Camera

Enclosure

Camera

Power Cable

HD Video Cable

2 Installation

Before you start:

l Please make s ure that the dev ice i n the p ackage

is in good condition and all the assembly parts

are i ncl ude d.

l Make sure that all the rel ated equipment is

power-off during the installation.

l Check the specificatio n of th e products for t he

installation environment.

l Check whether the power su ppl y is matched

with you r power output to avoid damage.

l Please make sure the wall is strong enough to

withstand three times the weight of the camera

and the mounting.

l If the wall is the cement wall, you need to i nse rt

exp ans ion s crews before yo u install the ca mera.

If the wall is the wooden wall, you can use

self-tapping screw to secure th e cam era.

l If the product does not function properly,

please contact your dealer or the nearest

service center. Do not disassemble the cam era

for repair or maintenance by yourself.

3.Route the cables to the cable hole and connect

the corresponding power cable and video cable.

4.Fix the camera to the ceiling with the supplied

screws.

P Direction

0 to 360°°

0 to 180°°

0 to 360°°

T Direction

R Direction

Figure 2-3 3-axis Adjustment

2.2 Installation of Type II Camera

Steps:

1.Drill the screw holes and the cable hole on the

ceiling according to the supplied drill template.

Cable Hole

Figure 2 -5 Fi x the Mounting Base and Camera

3.Ro ute the cables to the c able hole and connect

corresponding power cable and video cable.

4.Secure the camera to th e mou nting base.

Adjust the camera according to the figure below

to get an optimum angle.

2.1 Installation of Type CameraI

Steps:

1.Drill the screw holes in the ceiling according

to the supplied drill template.

2.Hammer the supplied plastic expansion bolt into

the scre w holes.

All Screw Holes: for

mounting base

Figure 2-1 Drill Template

Figure 2-2 Fix the Camera to the Ceiling

5.Adjust the surveillance angle.

1).Loosen No.3 adjusting screw to adjust the

panning position 0 ~ 360 .(° °)

.2).Tighten No.3 adjusting screw

3).Loosen the No.2 adjusting screw to adjust the

tilting position 0 ~ 180(° °).

4).Tighten No.2 adjusting screw.

5).Loosen No.1 adjusting screw to adjust the

azimuth angle of the image 0 ~ 360(° °).

.6).Tighten No.1 adjusting screw

Screw Hole

Figure 2-4 The Drill Template

2.Fix the mounting base to the ceiling with the

supplied screws.

0 to 360°°

P Direction

0to 75°°

T Direction

0 to 360°°

R Direction

Figure 2-6 3-axis Adjustment