Turret & Dome Camera
User Manual
UD.6L0201D1443A01
www.hikvision.com
Thank you for purchasing our product. If there
are a ny questi ons, or req uests, pleas e do not
hesitate to contac t the dealer.
This manual applies to
Type
720P
1080P
This man ual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice.
The upda tes will be a dded to the new versio n of
this manual. We will readily improve or update
the products or procedures described in the
manual.
Please refer to the product specification for
camera parameters and functions.
0100001040523
Model
DS-2CE56C2T-IRM
I
DS-2CE56C2T-IR
DS-2CE56C2T-IT1
II
DS-2CE56C2T-IT3
III
DS-2CE56C2T-IRMM
DS-2CE56D5T-IRM
I
DS-2CE56D5T-IT1
II
DS-2CE56D5T-IT3
Regulatory Information
FCC Information
FCC compliance: This equipment has been
tested and found to comply with the limits for a
digital device, p ursuant to part 15 of the FCC
Rules. T hese limits are designed to provid e
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
gen erates, uses, and ca n radiate ra dio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cau se ha rmful interfe rence to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
req uired to correct the i nterfere nce at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This de vice may no t cause harmfu l
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked
with "CE " and comply the refo re with
the applicable harmonized European
standards li sted u nder the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC,
the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points.
For more information see:
2006/66/EC (battery directive):This
product contains a battery that cannot
be disposed of as unsorted municipal
waste in the European Union.
www.recyclethis.info.
See the product documentation for specific
bat tery informat ion. The battery is marked with
this symbol, whic h may inclu de letter ing to
indicate cad mium (Cd), lea d (Pb ), or mercu ry (Hg).
For p roper recycling, return the battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
1 Introduction
1.1 Product Features
This ser ies of camera adopts new generation
sensor with high sensitivity and advanced circuit
design technology It features high resolution,.
low image distortion and low n ois e, etc , which.
makes it suitable for surveillance system and
image processing system.
l High performance CMOS sensor and high
resolution bring high-quality image;
l Low illumination;
l OSD menu , parameters are conf igu rabl e;
l Support auto white balance, auto gain control,
electronic shutter control;
SMART IR m ode;
l
l
Unit transmission control;
l Advanced 3-axis design meets different
installation requirements.
1.2 Overview
1.2.1 Overview of Typ e I Cam era
Enclosure
Switch Cable
Mounting Base
1.2.2 Overview of Typ e Cam era
Tri m Ring
Enclosure
Analog Video Cable
II
Camera
Analog Video Cable
Power Cab le
TVI
Mounting Base
Power Cab le
Switch Cable
TVI
1.2.3 Overview of Type CameraIII
Black Liner
Lower
Dome
Lock Screw
Camera
Analog Video Cable
Switch Cable
Power Cab le
TVI
2 Installation
Before you start:
l Please make sure th at the devi ce in the package
is in good condition and all the assembly parts
are i ncluded.
l Make sure that a ll the rela ted equip ment is
power-off during the installation.
l Check the specification of the products for the
installation environment.
l Check wheth er the power sup ply is matc hed
with your power out put to avoid damage.
l Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
l If the wall is th e cement wa ll, you nee d to insert
exp ansion screws before you i nsta ll the camera.
If the wall is the wooden wall, you can use
self-tapping screw to secu re the came ra.
l If the product does not function properly,
please contact your dealer or the nearest
service center. Do no t disassemble the camera
for repair or maintenance by yourself.
2.1 Installation of Type CameraI
Steps:
1.Drill t he screw ho les and the cabl e hole
according to the drill template.
Screw Hole
Drilling Template
Screw Hole
Screw Hole
2.Fix the mounting base to the ceiling with the
supplied screws.
3.Ro ute the cab les to the ca ble hole and con nec t
the correspondi ng power ca ble a nd video ca ble .
4.Secure the camera to the mounting base.
5.Fix the e nclosure to camera to complet t he
installation.
Figure 2-1 The Drill Template
Figure 2-2 Fix the Mo unting Base an d the C amera
6.Adjus t the camera acco rding to th e figure below
to get an optimu m ang le.
0~75°°
0 ~360°°
0 ~360°°
Figure 2-3 3-axis Adjustment
2.2 Installation of Type CameraII
Steps:
1.Drill t he screw ho les and the cabl e hole on the
ceiling according to the supplied drill template.
Mounting Base
Hole
Figure 2-4 The Drill Template
2.Fix the mounting base to the ceiling with the
supplied screws.
Figure 2-5 Fix the Mo unting Base an d Cam era
3.Ro ute the cab les to the ca ble hole and con nec t
corresponding power cable and video cable.
4.Secure the camera to the m ounting base .
5.Fix the e nclosure to camera .
6.Attac h the trim ring to t he camera and rot ate
it clockwise to secure the camera loosely.
0 ~360°°
Figure 2-6 3-axis Adjustment
Hole
0~75°°
0 ~360°°
2.3 Installation of Type CameraIII
Steps:
1.Hold t he mounting ba se, and rot ate th e lower
dome counterclockwise to disassemble the
lower dome and the black l iner.
2.Dril l the screw h oles and the cab le hole on the
ceiling according to the supplied drill template.
Screw Hole
Drilling Template
Screw Hole
Figure 2-7 The Drill Templ ate & Mounting
Base Installation
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4.Fix the mounting base to the ceiling with
the supplied screws.
355°
0-90°
5.Adjust the Lens
1).Loosen the tilting lock screws besides the
2).Adjust the camera from the pan angle
(0 ~ 355 ); tilt angle (0 ~ 90 ), and rotate°° °°
the lens (0 ~3 55 ) to get the o ptimum angle .°°
3).Tighten the tilting lock screws.
6.Fit the b lack liner bac k to the camera.
7.Install the lower dome back t o the camera and
rotate it c lockwise to get it secured.
355°
Figure 2-8 3-axis Adjustment
& Lower Dome
lens.
3 Menu Operation
Menu
VIDEO.
OUT
BACKLIGHT
EXPOSURE
SCENE
INDOOR
OUTDOOR
INDOOR1
LOWLIGHT
LENS
MANUAL
SHUTTER
AGC
SENS-UP
BRIGHTNESS
D-WDR
DEFOG
HSBLC
WB
BLC
ATW
AWC-SET
INDOOR
OUTDOOR
MANUAL
Figure 3-1 Main Menu
A coaxial camera controller (purchase separately)
is required to select the menu and adjust the
camera parameters.
SETUP
DAY&NIGHT
COLOR
B/W
EXT
LAUGUAGE
2D NR
3D NR
ADJUST
SPECIAL
NR
CAM
SHARPNESS
TITLE
D-EFFECT
MONITOR
MOTION
LSC
PRIVACY
DEFECT
VERSION
RESET
EXIT
3.1 VIDEO.OUT
PAL or NTSC is selectable .
3.2 LANGUAGE
Englis h, Japanese, CHN1 , CHN2, Korean, Germ an,
French, Italian, Spanish, Polish, etc., are selectable.
3.3SETUP
3.3.1 SCENE
You can select indoor, outdoor, indoor 1 and low
-light a s the worki ng environments.
3.3.2 LENS
The came ra is eq uip ped with a fixed lens.
3.3.3 EXPOSURE
SHUTTER: AUTO,1/25, 1/50, FLK, 1/200, 1/400,
1/1k, 1/ 2k, 1/5k, 1/10k, 1/ 50k, x2, x4, x6, x 8, x10,
and x15 are selectable.
: You can set th e AGC value f rom 0 to 15.AGC
: You can set th e SEN S-UP to OFF o r AUTO.SENS-UP
: You can set th e bri ghtness valueBRIGHTNESS
fro m 1 to 100.
: You can set th e D-W DR to ON to imp roveD-WDR
the imag e quality or OFF to disable the fu nction.
: You can set th e defog fun ction as ON toDEFOG
enable the function. Position, size, and the defog
gradation are configurable.
EXPOSURE
1. SHUTTER AUTO
2. AGC OFF
3. SENS-UP ---
4. BRIGHTNESS ---|------ 40
5. DEFOG OFF
6. BACKLIGHT OFF
7. RETURN RET
Figure 3-2 Exposure
HSBLC
1. SELECT AREA 1
2. DISPLAY ON 8
3. LEVEL ---|------ 40
4. MODE ALL DAY
5. BLACK MASK ON
6. DEFAULT 8
7. RETURN RET
Figure 3-3 HSBLC
3.3.4 Backlight
Backlight Compensation (BLC):
Set the gain of BLC as High, Middle, or L ow.-GAIN:
Press the up/down/left/right button to-AREA:
define the BLC position and size. Select RET or
AGA IN to go back the BLC menu or re- define th e
BLC a rea.
Restore t he BLC settings to the d efau lt.-Default:
HSBLC:
Select an HSBLC area. Set the DISPLAY status as ON.
Press the up/down/left/right button to define the
are a position and size. Set th e HSBLC LEVEL from 0
to 100. Select ALL DAY or Night for the HSBLC mode.
Set the BL ACK MASK status as ON or O FF.
3.3.5 White Balance (WB)
INDOOR, OUTDOOR, MANUAL, ATW (Auto-tracking
White Balance), AWC→SET are selectable.
3.3.6 Day & Night
Color, B/W, and EXT are selectable for DAY and
NIGHT switches.
3.3.7 NR
: You can set 2D N R stat us as O N or OFF.2D NR
: Set the Smart NR status as ON and adjust3D NR
the 3D sma rt NR sensitivity range s from 0 to 100 .
Set the 3D N R LEVEL ran ges from 0 to 100. Set the
START. AGC l evel as the t hreshol d to enable AGC,
and set th e END. A GC level as t he threshold to
disable AGC.
2D&3D NR
1. 2DNR O FF
2. 3DNR O N
3. RETURN RET
Figure 3-5 NR
8
3D NR
1. SMART NR ON
2. LEVEL ------|--8 0
3. START. AGC -|--------10
4. END. AGC -|--------10
5. RETURN RET
8
Figure 3-6 3D NR
3.3.8 SP ECIAL
: Edi t the camera title on this se ction.Camera Title
:D-effect
: Set the freeze function a s ON or OFF.-FREEZE
: OFF, MIR ROR, V-FLIP, and ROTATE are-MIRROR
selectable for mirror.
: Def ine t he zoo m area by con figuring-D-ZOOM
the posi tion from PAN & TILT.
: The D-Zoom area, sensitivity-SMART D-ZOOM
and time are configurable.
: Set the NEG IMAGE as ON o r OFF.-NEG.IMAGE
SPECIAL
1. CAM TITLE ON
2. D-DFFECT 8
3. MOTION OFF
4. PRIVACY O FF
5. LANGUAGE ENG
6. DEFECT 8
7. VERSION 130722
8. RETURN RET
8
8
Figure 3-7 Special
Figure 3-8 Motion Detection
MOTION
1. SELECT AREA 1
2. DISPLAY ON8
3. SENSITIVITY ----|---- 30
4. MOTION VIEW ON
5. DEFAULT 8
6. RETURN RET
Motion: Select a MOTION area. Set the DISPLAY
status as ON or OFF. Press the up/down/left/right
button to defi ne the positio n and s ize of t he area.
Set the SE NSITIVITY from 0 to 60. Set t he MOT ION
VIEW status as O N or OF F.
Privacy: Select a PRIVACY area. Set the DISPLAY
status as INV, MOSAIC, COLOR or OFF. Pre ss th e
up/down/left/right button to define the position
and size of the area.
Defect: LIVE DPC, STATIC DPC and Black D PC are
adjustable in this section.
: You can check the s oftware versi on of theVersion
device.
Figure 3-9 Privacy Mask
PRIVACY
1. SELECT AREA1
2. DISPLAY MOSAIC
3. COLOR 10
4. TRANS. 1
5. DEFAULT
6. RETURN RET
8
ADJUST
8
1. SHARPNESS
2. MONITOR LCD8
3. LSC OFF
4. VIDEO. OUT PAL
5. RETURN RET
--------|15
Figure 3-10 Adjust
3.3.9 ADJUST
: Adjust the sharpness from 0 to 15.Sharpness
: Monitor CRT, and Monitor LCD areMonitor
selectable.
: Set the LS C stat us as ON or OFF.LSC
3.3.10 RESET
Res et all the settings to t he defaul t.
3.3.11 EXIT
Pre ss OK to exit t he menu.