Hikvision DS-2CE56C2N-IT3-12, DS-2CE56C2N-IT3-2-8MM, DS-2CE56C2N-IT3-3, DS-2CE56C2N-IT3-6MM User Manual
Dome Camera
User Manual
www.hi kv is io n. com
Thank you for purchasing our pro du ct . If t he re
are a ny questions, or re qu ests, please do not
hesitate to contact the dealer.
This manual applies to
Type
Model
I
DS- 2CE55 82P(N ), DS-2 CE55C 2P(N)
DS- 2CE55 82P(N )-IRP, DS-2C E55C2 P(N)- IR P
DS- 2CE55 82P(N )-IR, DS-2C E55C2 P(N)- IR
DS- 2CE56 82P(N )-IT3 , DS-2C E56C2 P(N)- IT3
II
III
IV
DS- 2CE55 82P(N )-VFI R3
This manual may contain seve ral tec hn ic al
incor re ct p laces or printing errors, and the
con tent is subject to change w it ho ut n ot ic e.
The updat es w il l be a dd ed to the new versi on o f
this manual. We will rea di ly i mp rove or updat e
the pro du ct s or p rocedures described in the
manual.
DISCLAIMER STATEMENT
Underwriters Laborat or ie s In c. ( ”UL”) has not
tes ted the perfo rm an ce o r reliability of the
security or signaling aspects of this pro du ct .
Regulatory Information
FCC Information
FCC com pl ia nc e: T hi s eq ui pm ent has been
tes ted and fou nd t o comply with the limits for a
digital d ev ic e, p ursuant to pa rt 1 5 of t he FCC
Rules. These limits are d es ig ne d to provide
rea so na bl e protection agai nst harmful
int er feren ce w he n th e eq ui pm ent is operated in
a com me rcial environ me nt. This equipment
gen erates, uses, a nd c an radiate radio
fre qu en cy e ne rgy and, if not insta ll ed a nd u se d
in acco rd an ce with the instruction manual, may
cau se h ar mf ul i nterference to rad io
com mu ni cations. Operat io n of t hi s eq ui pm ent in
a res id ential area is likely to cause harmf ul
int er feren ce i n wh ic h case the user will be
req ui red to correc t th e interfe rence at his own
exp en se .
UL Certificat io n do es n ot
perfo rm an ce o r reliability of the
signaling aspects of this pro du ct U L MA KES NO
REPRESE NTATIONS, WARRANTIES OR
CERTI FI CATIONS WHATSOEVER REGARDING
THE PERFO RM AN CE O R RE LI AB IL IT Y OF A NY
SEC UR IT Y OR S IG NA LI NG R EL ATED FUNCTIONS
OF THIS PRO DU CT.
cov er the
security or
0100001030115
FCC Con di ti on s
This device com pl ie s wi th p ar t 15 o f th e FCC
Rules. Operation is subject to the fol lowing two
con di ti on s:
1. This devic e may not cause harmful
int er feren ce .
2. This devic e mu st a cc ept any int er feren ce
rec ei ved, including interference that m ay
cau se u nd es ir ed o perat io n.
EU Conformity Statement
This prod uc t an d - if a pp li cable -
the supplied accessories to o are
marked with "CE" and comply
up on t h e pu rch as e o f eq uiv al ent n ew e q ui pme nt ,
or d is p os e of it a t de s ig nat ed co ll ect ion p oi n ts .
For mo re i n fo rma tio n se e:
www.recyclethis.info.
2006/66/EC (b attery dire ct ive):
This prod uc t contains a battery
that ca nn ot b e di sp os ed o f as
unsorte d mu ni ci pa l waste in the
Europ ea n Un io n.
See the pro du ct d oc um entation for specific
bat tery info rm at ion. The batter y is m ar ked with
this sy mb ol , wh ic h may include lettering to
indicate cadmium (Cd), lead (Pb), or mercu ry ( Hg ).
For p roper recyc li ng , return the batter y to your
supplier or to a de si gn ated collection point . For
more in formation see :
www.recyclethis.info.
This series of ca me ra adopts new generation
sensor with high sensitivity and adva nc ed c ircuit
design te ch no lo gy . It features high res ol ut io n
low image d istortion and low noise etc . w hi ch
makes it suitable fo r su rveillance system and
image p rocessing sys tem.
●High-perfor ma nc e sensor and high resolution
bring high-quality image
●IR LED enables day nig ht sur veillance
●Day /n ig ht auto switc h
●ATW brings high color ren di ti on
●Auto el ec tronic shutte r co ntrol to ad ap t to t he
different su rvei ll an ce e nviro nm en ts
●Auto gain contro l, a da pt ive brightness
●High SNR brings high-quality image
●Ingre ss p rotection: IP66
Type Ⅰ came ra doesn’t support day nig ht auto
switc h an d IP .
DS-2CE5582P N IRP and DS- C E5 5C P N IRP
don’t support IP66.
,
, ,
/
Notes :
/
66
( )- 2 2 ( ) -
1 Introduction
1.1 Product Features
1.2 Overview
2 Installation
Befor e yo u start:
●Please make sure that th e de vi ce i n th e pa ckage
is in goo d co nd it io n an d al l th e as se mb ly p ar ts
are i nc lu de d.
●Please make sure that al l th e related equipme nt
is powe r- of f du ring the installati on .
●Check the specifica ti on o f th e products fo r th e
installation environment.
●Check whether t he p ow er s up pl y is m atched
with yo ur A C ou tl et to avo id d am age.
●If the prod uc t do es n ot f un ct io n properly, pl ea se
con tact your dealer or the neare st ser vi ce
cente r. Do not disassemble the camera for
rep ai r or m ai ntenance by you rself.
●Please make sure that th e wall or the ceiling is
strong enough to withsta nd 3 t im es t he weight
of the ca me ra.
UD.6L0201D0172A01
there fore wi th t he a pp li cable harmonized
Europ ea n standards l is ted under the Low Voltage
Direc ti ve 2006/95/EC, the EMC Dire ct ive 2004/
108/EC.
UL has only tes ted for f ire, shock or casualty
hazards as outlined in Ul’s Sta nd ard(s) for Sa fety,
UL60950-1.
2002/96/EC (W EE E di rective):
Pro du ct s ma rked with this symbol
can no t be d is po se d of a s un so rt ed
mu ni c ip al wa st e in th e Eur op e an
Un io n . Fo r pr ope r rec yc lin g, r e tu rn
th is p r od uct t o yo ur lo cal s up p li er
Power
Cable
Power
Cable
Power Cable
Zoo m & Focu s
Video C able
Video
Cable
Power Cable
Mounting
Base
Lock
Screw
Enclo sure
Camera
TYPE
II
Enclo sure
Trim Ring
Mounting
Base
Video
Cable
Enclo sure
Trim Ring
Mounting
Base
Video
Cable
Camera
TYPE
III
Camera
Adjust able Screw
Black L iner
Lower
Dome
TYPE
IV
TYPE
I
Camera
1.Hold the mounti ng b as e, a nd rotate t he l ower
dome co un terclockwise to d is as se mb le t he
lower d om e an d th e bl ac k li ne r.
2.Drill the screw h ol es and the cable hole the
ceiling according to the supplied drill templa te.
on
83.5
2-∅4.5
Ste ps :
Figure 2- 1 Th e Di sa ss em bl in g
2.1 Ceiling Mounting for Type I
Camera
3.Ro ute the cables to t he cab le h ol e an d
the cor re sp on di ng p ower cable and video ca bl e.
4.Secure t he m ou nting base to the ceiling with
the self ta pp in g sc rews.
con ne ct
-
6.Fit the black liner back to th e camera.
7.Install the lower dome back to the ca me ra and
rotate it clockwis e to get it secured.
Figure 2- 2 Th e Se cu ri ng & 3 -axis Adjustment
5.Adjust t he L en s
1).Loosen the tilting lock screws besides the
lens.
2).Adjust th e ca me ra from t he p an a ng le
( deg rees); tilt angle (0~90 degre es ),
and rotate the lens(0~355 degr ee s) to get the
optimum angle.
3).Tight en t he t ilting lock screws.
0~355
108
Screw Hole
∅86
108
∅72
Ste ps :
1.Drill the scre w ho les and th e cable hole
accor di ng to the drill templat e.
Figure 2- 5 Dr il l Temp late of Type Ⅲ Camera
2.Secure t he m ou nting base to the ceiling with
the screws.
Figure 2- 6 Se cu re the Mounting Base
3.Ro ute the cables to t he cab le h ol e an d
the cor re sp on di ng p ower cable and
video cab le .
4.Secure t he camera to th e mo un ti ng b as e.
5.Install the enclosure and the trim ring to
cam era.
con ne ct
Figure 2- 7 Se cu re the Components
Camera
Figure 2- 4 Dr il l Temp late of Type Ⅱ Camera
110
Hole
Ceiling Mounting
Hole
110
∅102
∅5
∅20
83.5
2.2 Ceiling Mounting for Type II/ III
Screw Hole
Template
3-∅4.5
∅110
45
39
39
22.5
22.5
6.Adjust t he s ur ve il la nc e an gl e ac cording to th e
figure be lo w.
7.Ro tate th e tr im r in g cl oc kw is e to secure the
cam era.
Figure 2- 10 T he L oc k Sc rew
Figure 2- 8 Le ns A dj ustment
2.3 Ceiling Mounting for Type IV
Camera
Figure 2- 9 Th e Dr il l Temp late
2.Loosen the lock scre w to disassemble the
cam era from the mounti ng b as e.
3.Secure t he m ou nting base to the ceiling.
Ste ps :
1.Drill the scre ws holes and the cable hole on the
ceiling according to the supplied drill templa te.
360°
360°
0-75°
P 0°an -360°
Rotation 0°-360°
Tilt 0°-75°
4.Ro ute the cables to t he cab le h ol e an d connect
the cor re sp on di ng cables.
5.Secure t he camera to th e mo un ti ng b as e by
tight en in g th e lo ck screw.
6.Adjust t he c am era accordi ng to the figure
below to get an optimum angle.
Figure 2- 11 L en s Ad ju stment
7.U se t he s crewdriver to a dj ust the ZOOM scre w
and the FOC US s crew until yo u ge t th e
optimum image .
Figure 2- 12 Zoom and Focus Adjust me nt
2.4 Power Supply
Figure 2- 13 T he Power Cable & the Vide o Ca bl e
Note:
Please make sure that th e po wer adapter is
com pa ti bl e wi th t he camera, an d the standard
power s up pl y is 1 2V D C. Please refer to t he
tec hn ic al s pe ci fi cation fo r mo re info rm ation.
Figure 2- 3 Co mp le te the Instal la tion
Loading...