TurboHD
DS-2CE16D0T-WL3
TVI Bullet Camera
User Manual
Thank you for purchasing our product. If there are any questions, or requests, do
not hesitate to contact the dealer.
This manual may contain several technically incorrect places or printing errors, and
the content is subject to change without notice. Updates will be added to new
versions of this manual. We will readily improve or update the products or
procedures described in the manual.
UM DS-2CE16D0T-WL3 061818NA 2018 Hikvision USA Inc.
Regulatory Information
these safeguards to
precautions to prevent
prevent serious injury
potential injury or
or
death.
material damage.
FCC Information
FCC Compliance: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case the user will be required to correct
the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
EU Conformity Statement
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly
to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions.”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are
neglected.
This product and, if applicable, the supplied accessories too are
marked with “CE” and comply therefore with the applicable
harmonized European standards listed under the EMC Directive
2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE Directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Warnings Follow Cautions Follow these
Warnings
•
In use of the device, you must be in strict compliance with the electrical safety
regulations of the nation and region.
•
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the
Limited Power Source with 12 VDC according to the IEC60950-1 standard. Refer
to technical specifications for detailed information.
•
Do not connect multiple devices to one power adapter to avoid overheating or
fire hazard caused by overload.
•
Make sure that the plug is firmly connected to the power socket.
UM DS-2CE16D0T-WL3 061818NA 2018 Hikvision USA Inc.
•
Make sure that the device is firmly fixed if wall mounting or ceiling mounting is
adopted.
•
If smoke, odor, or noise rise from the device, turn off the power at once and
unplug the power cord, and then contact the service center.
•
Never attempt to disassemble the camera by unprofessional personal.
Cautions
•
Do not drop the camera or subject it to physical shock.
•
Do not touch sensor modules with fingers.
•
If cleaning is necessary, use a clean cloth with a bit of ethanol, and wipe it gently.
•
Do not aim the camera at the sun or extra bright places.
•
The sensor may be burned out by a laser beam, so if any laser equipment is in
use, make sure that the sensor surface is not exposed to the laser beam.
•
Do not expose the device to high electromagnetic radiation or extremely hot,
cold, dusty, or damp environments.
•
To avoid heat accumulation, good ventilation is required for the operating
environment.
•
Keep the camera away from liquid while in use for a non-waterproof device.
•
While in delivery, the camera shall be packed in its original packing or packing of
the same texture.
UM DS-2CE16D0T-WL3 061818NA 2018 Hikvision USA Inc.
1. Introduction
1.1 Product Features
The camera is applicable for outdoor conditions, and the application
scenarios include roads, parking lots, campuses, etc.
The main features are as follows:
•
High performance CMOS sensor
•
1080p resolution
•
Auto white balance
•
Auto electronic shutter
•
Auto gain control (AGC)
•
White supplement light
•
Up-the-Coax (HIKVISION-C)
1.2 Overview
1.2.1 Camera Overview
Figure 1, Camera Overview
1.3 Installation Preparation
Before you start:
•
Make sure that the device in the package is in good condition and all
the assembly parts are included.
•
Make sure that all the related equipment is powered-off during the
installation.
•
Check the specification of the products for the installation
environment.
•
Check whether the power supply matches your power output to
avoid damage.
•
Make sure the wall is strong enough to withstand three times the
weight of the camera and the bracket.
•
If the wall is cement, insert expansion bolts before you install the
camera. If the wall is wood, use self-tapping screws to secure the
camera.
•
If the product does not function properly, contact your dealer or the
nearest service center. Do NOT disassemble the camera for repair or
maintenance yourself.
1.4 Wall Mounting
Before you start:
The package contains the wall mounting bracket.
Steps:
1. Attach the bracket to the wall.
2. Mark the screw holes on the wall according to the holes on the
bracket.
UM DS-2CE16D0T-WL3 061818NA 2018 Hikvision USA Inc.
3. Drill the screw holes.
4. Attach the bracket to the wall and secure the camera with supplied
screws.
Figure 2, Secure the camera to the wall
Note:
•
The supplied screw package contains both self-tapping screws and expansion
bolts.
•
If the wall is cement, expansion bolts are required to fix the camera. If the wall
is wood, self-tapping screws are required.
5. Align the camera to the pedestal, and secure the camera on the
pedestal with supplied screws.
Figure 3, Secure the Camera on the Bracket
6. Route the cables and connect the corresponding power cord and
video cable.
7. Power on the camera to check whether the image on the monitor is
at an optimum angle. If not, adjust the camera according to the
figure below to get an optimum angle.
1). Loosen the horizontal adjusting screw to adjust the pan
position (0° to 360°).
2). Tighten the horizontal adjusting screw.
3). Loosen the vertical adjusting screw to adjust the tilt
position (0° to 90°)
4). Tighten the vertical adjusting screw.
Figure 4, Angle Adjustment
UM DS-2CE16D0T-WL3 061818NA 2018 Hikvision USA Inc.
1.5 Pendant Mounting
Before you start:
You must purchase a pendant bracket.
Steps:
1. Attach the bracket to the ceiling.
2. Mark the screw holes on the ceiling according to the holes on the
bracket.
3. Drill the screw holes.
4. Attach the bracket to the ceiling and secure the camera with
supplied screws.
Figure 5, Fix the Bracket on the Ceiling
Note:
•
The supplied screw package contains both self-tapping screws and expansion
bolts.
•
If the wall is cement, expansion bolts are required to fix the camera. If the wall is
wood, self-tapping screws are required.
5. Remove the screw on the top of the camera to expose the screw
hole.
Figure 6, Remove the Screw
6. Align the screw hole on the top of the camera with the pendant
mounting bracket and rotate the camera to fix it.
UM DS-2CE16D0T-WL3 061818NA 2018 Hikvision USA Inc.
Figure 7, Fix the Camera to the Bracket
7. Route the cables and connect the corresponding power cord and
video cable.
8. Power on the camera to check whether the image on the monitor is
at an optimum angle. If not, adjust the camera according to the
figure below to get an optimum angle.
1). Loosen the adjusting knob to adjust the pan position (0°
to 360°) and tilt position (0° to 90°)
2). Tighten the adjusting knob.
Figure 8, Angle Adjustment
UM DS-2CE16D0T-WL3 061818NA 2018 Hikvision USA Inc.
Loading...