HIKVISION DS-2CE16D0T-IT1E, DS-2CE16D0T-IRPE, DS-2CE56D0T-IT1E, DS-2CE16D0T-IRE, DS-2CE16D0T-IT5E User Manual

TURBO HD TVI

Bullet & Turret Camera

User Manual

User Manual

Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.

This manual applies to the model listed below.

Type

Model

Type I

DS-2CE16D0T-IT1E/3E/5E

Type II

DS-2CE16D0T-IRE/IRPE

Type III

DS-2CE56D0T-IT1E/3E

This manual may contain several technically incorrect
places or printing errors, and the content is subject to
change without notice. The updates will be added to
the new version of this manual. We will readily improve
or update the products or procedures described in the
manual.

0100001080423

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and

found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,
including interference that may cause undesired
operation

EU Conformity Statement

This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the

applicable harmonized European
standards listed under the EMC Directive 2014/30/EU,
the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products

marked with this symbol cannot be

disposed of as unsorted municipal waste in

the European Union. For proper recycling,

return this product to your local supplier

upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.

Warning

This is a class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.

Safety Instruction

These instructions are intended to ensure that user can
use the product correctly to avoid danger or property
loss.

The precaution measure is divided into “Warnings” and
“Cautions”

Warnings: Serious injury or death may occur if any of
the warnings are neglected.

Cautions: Injury or equipment damage may occur if any
of the cautions are neglected.

Warnings

 In the use of the product, you must be in strict

compliance with the electrical safety regulations of
the nation and region.

 Refer to technical specifications for detailed

information.

 Input voltage should meet both the SELV (Safety Extra

Low Voltage) and the Limited Power Source with 12 V
DC according to the IEC60950-1 standard. Refer to
technical specifications for detailed information.

 Do not connect several devices to one power adapter

as adapter overload may cause over-heating or a fire
hazard.

 Make sure that the plug is firmly connected to the

power socket.

 When the product is mounted on wall or ceiling, the

device shall be firmly fixed.

 If smoke, odor or noise rise from the device, turn off

the power at once and unplug the power cable, and
then contact the service center.

 If the product does not work properly, contact your

dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance.)

Cautions

 Make sure the power supply voltage is correct before

using the camera.

 Do not drop the camera or subject it to physical

shock.

 Do not touch senor modules with fingers. If cleaning

is necessary, use clean cloth with a bit of ethanol and
wipe it gently.

 Do not aim the camera at the sun or extra bright

places. Blooming or smearing may occur otherwise
(which is not a malfunction), and affect the
endurance of sensor at the same time.

Warnings Follow
these safeguards to
prevent serious injury
or death.

Cautions Follow these
precautions to prevent
potential injury or
material damage.

 The sensor may be burned out by a laser beam, so

when any laser equipment is in using, make sure that
the surface of sensor will not be exposed to the laser
beam.

 Do not place the camera in extremely hot, cold, dusty

or damp locations, and do not expose it to high
electromagnetic radiation.

 To avoid heat accumulation, good ventilation is

required for operating environment.

 Keep the camera away from liquid while in use.
 While in delivery, the camera shall be packed in its

original packing, or packing of the same texture.

Introduction

1.1 Product Features

The camera is applicable for both indoor and outdoor
conditions, and the application scenarios include road,
warehouse, parking lot, office, campus, etc..

The main features are as follows:

 High performance CMOS sensor
 1080p resolution
 Auto white balance
 Auto electronic shutter
 Auto gain control (AGC)
 IR cut filter
 PoC
 3-axis adjustment

Note:

Type III camera is applicable for indoor condition only.

1.2 Overview

1.2.1 Type I Camera Overview

Power Cord

Video Cable

Mounting Base

Sun Shield

Lens

Figure 1. 1 Type I Camera Overview

1.2.2 Type II Camera Overview

Power Cord

Mounting

Base

Main Body

Lens

IR LED

Video Cable

Figure 1. 2 Type III Camera Overview

1.2.3 Type III Camera Overview

Enclosure

Camera

Mounting

Base

Power Cord

Video Cable

Figure 1. 3 Type II Camera Overview

Installation

2.1 Installation Preparation

Before you start:

 Make sure that the device in the package is in good

condition and all the assembly parts are included.

 Make sure that all the related equipment is power-off

during the installation.

 Check the specification of the products for the

installation environment.

 Check whether the power supply is matched with

your power output to avoid damage.

 Make sure the wall is strong enough to withstand

three times the weight of the camera and the
mounting bracket.

 If the wall is cement, insert expansion bolts before

installing the camera. If the wall is wooden, use
self-tapping screws to secure the camera.

 If the product does not function properly, contact

your dealer or the nearest service center. Do NOT
disassemble the camera for repair or maintenance by
yourself.

2.2 Installation of Type I Camera

Before you start:

Both wall mounting and ceiling mounting are suitable
for the bullet camera. Ceiling mounting will be taken as
an example in this section. You can take the steps of
ceiling mounting as a reference, when adopting the wall
mounting.

Steps:

1. Paste the dill template to the ceiling.

2. Drill the screw holes according to the drill template,

and the cable hole (optional) on the ceiling.

47.6

13.7

27.5

Φ

68

3

-

Φ

4

Unit： mm

Figure 2. 1 Drill Template

Note:

Cable hole is required when adopting ceiling outlet
to route the cable.

3. Attach the mounting base of the type I camera to

the ceiling and secure the camera with supplied
screws.

Figure 2. 2 Secure the Camera to the Ceiling

Note:

 The supplied screw package contains self-tapping

screws, and expansion bolts.

 For cement wall, expansion bolts are required to fix

the camera. For wooden wall, self-tapping screws
are required.

4. Route the cables through the cable hole (optional),

or the side opening.

5. Connect the corresponding power cord, and video

cable.

6. Power on the camera to check whether the image

on the monitor is gotten from the optimum angle.
If not, adjust the camera according to the figure
below to get an optimum angle.

0° to 90°

0° to 360°

0° to 360°

1

2

3

Figure 2. 3 3-Axis Adjustment

1) Loosen the No.1 adjusting screw to adjust the

pan position (0° to 360°).

2) Tighten the No.1 adjusting screw.

3) Loosen the No.2 adjusting screw to adjust the

tilting position (0° to 90°).

4) Tighten the No. 2 adjusting screw.

5) Loosen the No.3 adjusting screw to adjust the

rotation position (0° to 360°).

6) Tighten the No.3 adjusting screw.

2.3 Installation of Type II Camera

Before you start:

Both wall mounting and ceiling mounting are suitable
for the bullet camera. Ceiling mounting will be taken as
an example in this section. You can take the steps of
ceiling mounting as a reference, when adopting wall
mounting.

Steps:

1. Paste the dill template to the ceiling.

2. Drill the screw holes according to the drill template,

and the cable hole (optional) on the ceiling.

47.6

13.7 27.5

Φ

68

3

-

Φ

4

Unit: mm

Figure 2. 4 Drill Template

Note:

Cable hole is required when adopting ceiling outlet
to route the cable.

3. Attach the mounting base of the type I camera to

the ceiling and secure the camera with supplied
screws.

Figure 2. 5 Secure the camera to the ceiling

Note:

 The supplied screw package contains self-tapping

screws, and expansion bolts.

 For cement wall, expansion bolts are required to fix

the camera. For wooden wall, self-tapping screws
are required.

4. Route the cables through the cable hole (optional),

or the side opening.

5. Connect the corresponding power cord and video

cable.

6. Power on the camera to check whether the image

on the monitor is gotten from the optimum angle.
If not, adjust the camera according to the figure
below to get an optimum angle.

0° to 360°

1

2

3

0° to 360°

0° to 180°

Figure 2. 6 3-Axis Adjustment

1). Loosen the No.1 adjusting screw to adjust the

pan position (0° to 360°).

2). Tighten the No.1 adjusting screw.

3). Loosen the No.2 adjusting screw to adjust the

tilting position (0° to 180°).

4). Tighten the No. 2 adjusting screw.

5). Loosen the No.3 adjusting screw to adjust the

rotation position (0° to 360°).

6). Tighten the No.3 adjusting screw.

2.4 Installation of Type II camera

Before you start:

Both wall mounting and ceiling mounting are suitable
for the turret camera. Ceiling mounting will be taken as
an example in this section. You can take the steps of
ceiling mounting as a reference, when adopting wall
mounting.

Steps:

1. Disassemble the turret camera by rotating the

camera to align the notch to one of the marks, as
shown in Figure 2. 1.

Mark

Notch

Figure 2. 7 Disassemble the Camera

2. Remove the mounting base from the camera body

with a flat object, e.g., a coin.

3. Paste the drill template (supplied) to the place

where you want to install the camera, and then drill
the screw holes and the cable hole (optional) on the
ceiling according to the drill template.

Screw Hole

Cable Hole

Figure 2. 8 Drill Template

Note:

Cable hole is required when adopting the ceiling
outlet to route the cable.

4. Attach the mounting base to the ceiling and secure

them with supplied screws

Figure 2. 9 Attach the Mounting Base to the Ceiling

Note:

 The supplied screw package contains self-tapping

screws, and expansion bolts.

 For cement wall, expansion bolts are required to fix

the camera. For wooden wall, self-tapping screws
are required.

5. Route the cables through the cable hole (optional),

or the side opening.

6. Align the camera with the mounting base, and

tighten the screws to secure the camera with the
mounting base.

Figure 2. 10 Secure the Camera with Mounting Base

7. Connect the corresponding cables, such as power

cord, and video cable.

8. Power on the camera to check whether the image

on the monitor is gotten from the optimum angle. If
not, adjust the camera according to the figure below
to get an optimum angle.

Tilt Position Range
[0°to 75°]

Pan Position Range
[0° to 360°]

Rotation Position Range
[0°to 360°]

Figure 2. 11 3-axis Adjustment

1). Hold the camera body and rotate the enclosure

to adjust the pan position [0° to 360°].

2). Move the camera body up and down to adjust

the tilt position [0° to 75°].

3). Rotate the camera body to adjust the rotation

position [0° to 360°].

Menu Description

Purpose:

Call the menu by clicking button on the PTZ Control
interface, or call the preset No.95.

Steps:

1. Connect the camera with the TVI DVR, and the

monitor, shown as the figure 3-1.

Camera

TVI DVR

Monitor

Figure 3. 1 Connection

2. Power on the analog camera, TVI DVR, and the

monitor to view the image on the monitor.

3. Click PTZ Control to enter the PTZ Control interface.

4. Call the camera menu by clicking button, or call

the preset No. 95.

AE

EXPOSURE MODE

MAIN MENU

VIDEO

SETTINGS

SAVE & EXIT

AGC

RETURN

DWDR

CONTRAST

SHARPNESS

COLOR GAIN

DNR

MIRROR

RETURN

RESET

BRIGHTNESS

IMAGE

MODE

WB

RETURN

MODE

FORMAT

LANGUAGE

DAY-NIGHT

INFRARED

SMART IR

RETURN

MODE

Figure 3. 2 Main Menu Overview

5. Click the direction arrow to control the camera.

7). Click up/down direction button to select the

item.

8). Click Iris + to confirm the selection.

9). Click left/right direction button to adjust the

value of the selected item.

3.1 VIDEO FORMAT

You can select the video format as 1080p@25fps , or
1080p@30fps.

3.2 LANGUAGE

Supports English, and Chinese.

3.3 MAIN MENU

3.3.1 EXPOSURE

You are allowed to set BRIGHTNESS, EXPOSURE MODE,
AGC, and DWDR.

EXPOSURE

BRIGHTNESS
EXPOSURE MODE
AGC

DWDR

RETURN

5

G LO B AL

H IG H
O FF



Figure 3. 3 EXPOSURE

BRIGHTNESS

Brightness refers to the brightness of the image. You
can set the brightness value from 1 to 10 to darken or
brighten the image. The greater the value is, the
brighter the image is.

EXPOSURE MODE

You can set the EXPOSURE MODE as GLOBAL, or BLC.

 GLOBAL

GLOBAL refers to the normal exposure mode which
adjusts lighting distribution, variations, and
non-standard processing.

 BLC (Backlight Compensation)

BLC (Backlight Compensation) compensates light to the
object in the front to make it clear, but this may cause
the over-exposure of the background where the light is
strong.
You can set the brightness value from 0 to 8 to darken
or brighten the image. The greater the value is, the
brighter the image is.

AGC (Auto Gain Control)

It optimizes the clarity of the image in poor light
conditions. The AGC level can be set as HIGH, MIDDLE,
or LOW. Select OFF to disable the AGC function.

Note:

The noise will be amplified when the AGC is on.

DWDR (Digital Wide Dynamic Range)

The digital wide dynamic range helps the camera
provide clear images even under backlight
circumstances. WDR balances the brightness level of
the whole image and provides clear images with details.

3.3.2 WB (White Balance)

White balance, the white rendition function of the
camera, is to adjust the color temperature according to
the environment. It can remove unrealistic color casts in
the image. You can set WB mode as ATW, or MWB.

 ATW

Under the ATW mode, white balance is being adjusted
automatically according to the color temperature of the
scene illumination.

 MWB

You can set the RGAIN/BGAIN value from 1 to 255 to
adjust the shades of red/blue color of the image.

WB

MODE
RGAIN
BGAIN
RETURN

MWB

5

5



Figure 3. 4 MWB MODE

3.3.3 DAY/NIGHT

COLOR, B/W (Black White), and SMART are selectable
for DAY and NIGHT switches.

COLOR

The image is colored in day mode all the time.

B/W

The image is black and white all the time.

SMART

The IR light turns on automatically as the environmental
illumination becomes poor. You can set the value of
SMART IR in this menu.

DAY/NIGHT

MODE
SMART IR

RETURN

SMART
1



Figure 3. 5 DAY NIGHT

 SMART IR

The Smart IR function is used to adjust the light to its
most suitable intensity, and prevent the image from
over exposure. The SMART IR value can be adjusted
from 0 to 3. The greater the value is, the more obvious
effects are.

3.3.4 VIDEO SETTINGS

Move the cursor to VIDEO SETTINGS and click Iris+ to
enter the submenu. IMAGE MODE, CONTRAST,
SHARPNESS, COLOR GAIN, DNR, and MIRROR are
adjustable.

VIDEO SETTINGS

IMAGE MODE
CONTRAST
SHARPNESS
COLOR GAIN
DNR

MIRROR
RETURN

ST D

5

5

5

O FF





5

Figure 3. 6 VIDEO SETTINGS

IMAGE MODE

IMAGE MODE is used to adjust the image saturation,
and you can set it as STD (Standard) or HIGH-SAT (High
Saturation).

CONTRAST

This feature enhances the difference in color and light
between parts of an image. You can set the CONTRAST
value from 1 to 10.

SHARPNESS

Sharpness determines the amount of detail an imaging
system can reproduce. You can set the SHARPNESS
value from 1 to 10.

COLOR GAIN

Adjust this feature to change the gain of the color. The
value ranges from 1 to 10.

DNR (Digital Noise Reduction)

The DNR function can decrease the noise effect,
especially when capturing moving images in poor light
conditions, and delivering more accurate and sharper
image. You can set the DNR value from 1 to 9.

MIRROR

OFF, H, V, and HV are selectable for mirror.
OFF: The mirror function is disabled.
H: The image flips 180° horizontally.
V: The image flips 180° vertically.
HV: The image flips 180° both horizontally and

vertically.

3.3.5 RESET

Reset all the settings to the factory default.

3.3.6 SAVE & EXIT

Move the cursor to SAVE & EXIT, and click Iris+ to save
the settings, and exit the menu.

UD10298B