Hikvision DS-2CE12H0T-PIRL-2-8mm User Manual

TurboHD

DS-2CE12H0T-PIRL

Bullet Camera

User Manual

Thank you for purchasing our product. If there are any questions, or requests, do
not hesitate to contact the dealer.

This manual may contain several technical incorrect places or printing errors, and
the content is subject to change without notice. Updates will be added to new
versions of this manual. We will readily improve or update the products or
procedures described in the manual.

UM D-2CE12H0T-PIRL  2018 Hikvision USA Inc.

1 Regulatory Information

1.1 FCC Information

Please take attention that changes or modification not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.

FCC Compliance: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.

1.2 FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that
may cause undesired operation.

1.3 EU Conformity Statement

This product and, if applicable, the supplied accessories too are marked

standards listed under the Low Voltage Directive 2014/35/EU, the EMC Directive
2014/30/EU, the RoHS Directive 2011/65/EU.

collection points. For more information see: www.recyclethis.info.

indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the
battery to your supplier or to a designated collection point. For more information
see: www.recyclethis.info.

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.

The precaution measure is divided into “Warnings” and “Cautions.”

Warnings: Serious injury or death may occur if any of the warnings are neglected.

Cautions: Injury or equipment damage may occur if any of the cautions are

neglected.

with “CE” and comply therefore with the applicable harmonized European

2012/19/EU (WEEE Directive): Products marked with this symbol cannot
be disposed of as unsorted municipal waste in the European Union. For
proper recycling, return this product to your local supplier upon the
purchase of equivalent new equipment, or dispose of it at designated

2006/66/EC (Battery Directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
See the product documentation for specific battery information. The
battery is marked with this symbol, which may include lettering to

1.4 Industry Canada ICES-003 Compliance

1.5 Warning

1.6 Safety Instruction

UM D-2CE12H0T-PIRL  2018 Hikvision USA Inc.

Warnings

Follow

Cautions

Follow these

these safeguards to

precautions to prevent

prevent serious injury

potential injury or

or death.

material damage.

1.7 Warnings

• In the use of the device, you must be in strict compliance with the electrical
safety regulations of the nation and region.



• Input voltage should meet both the SELV (Safety Extra Low Voltage) and the
Limited Power Source with 12 VDC according to the IEC60950-1 standard. Refer
to technical specifications for detailed information.

• Do not connect multiple devices to one power adapter to avoid overheating or
a fire hazard caused by overload.

• Make sure that the plug is firmly connected to the power socket.

• Make sure that the device is firmly fixed if wall mounting or ceiling mounting is

adopted.

• If smoke, odor, or noise rise from the device, turn off the power at once and
unplug the power cord, and then contact the service center.

• Never attempt to disassemble the camera by unprofessional personal.



1.8 Cautions

• Do not drop the camera or subject it to physical shock.

• Do not touch sensor modules with fingers.

• Do not place the camera in extremely hot, cold (the operating temperature shall

be -40° to 60° C), dusty, or damp locations, and do not expose it to high
electromagnetic radiation.

• If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it
gently.

• Do not aim the camera at the sun or extra bright places.

• The sensor may be burned out by a laser beam, so when any laser equipment is

in use, make sure that the surface of the sensor will not be exposed to the laser
beam.

• Do not expose the device to high electromagnetic radiation or extremely hot,
cold, dusty, or damp environment.

• To avoid heat accumulation, good ventilation is required for the operating
environment.

• Keep the camera away from liquid while in use for non-waterproof device.





• While in delivery, the camera shall be packed in its original packing or packing of
the same texture.



1.9 Mark Description

Table 0-1 Mark Description

Mark Description

DC Voltage

UM D-2CE12H0T-PIRL  2018 Hikvision USA Inc.

2 Introduction

2.1 Product Features

The main features are as follows:

• High performance CMOS sensor

• IR cut filter with auto switch

• OSD menu with configurable parameters

• Auto white balance

• Internal synchronization

• SMART IR mode

• Visible alarm

• PIR detection

• 3-axis adjustment

2.2 Overview

2.2.1 Camera Overview





Figure 1, Camera Overview

Figure 1-2

3 Installation

Before you start

•

Make sure that the device in the package is in good condition and all the
assembly parts are included.

•

Make sure that all the related equipment is powered off during the
installation.

•

Check the specification of the products for the installation environment.

•

Check whether the power supply matches your power output to avoid
damage.

•

Make sure the wall is strong enough to withstand three times the weight





of the camera and the mount.

•

If the wall is cement, insert expansion bolts before installing the camera. If
the wall is wood, use self-tapping screws to secure the camera.

•

If the product does not function properly, contact your dealer or the
nearest service center. Do NOT disassemble the camera for repair or
maintenance yourself.

3.1 Camera Installation

3.1.1 Ceiling/Wall Mounting without Junction Box

Steps:

1. Paste the drill template (supplied) to where you want to install the
camera.

2. Drill the screw holes according to the drill template and the cable











UM D-2CE12H0T-PIRL  2018 Hikvision USA Inc.