How it Works
HIKVISION
Loading...
D
Loading...
Loading...
DS-2CE12H0T-PIRL
User Manual
16 pgs1.43 Mb0

HIKVISION DS-2CE11D0T-PIRL, DS-2CE12D0T-PIRL, DS-2CE11H0T-PIRL, DS-2CE12H0T-PIRL User Manual

Download
TURBO HD
D0T PIR Series Bullet
Camera
User Manual
User Manual
Type
Model
Type I Camera
DS-2CE11D0T-PIRL
Type II Camera
DS-2CE12D0T-PIRL
This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.
0200001080504
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the
applicable harmonized European standards listed under the Low Voltage Directive 2014/35/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a
battery that cannot be disposed of as
unsorted municipal waste in the European
Union. See the product documentation for
specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings
In the use of the device, you must be in strict
compliance with the electrical safety regulations of the nation and region.
Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 12 VDC according to the IEC60950-1 standard. Refer to technical specifications for detailed information.
Do not connect multiple devices to one power
adapter to avoid over-heating or a fire hazard caused by overload.
Make sure that the plug is firmly connected to the
power socket.
Make sure that the device is firmly fixed if wall
mounting or ceiling mounting is adopted.
If smoke, odor or noise rise from the device, turn off
the power at once and unplug the power cord, and then contact the service center.
Never attempt to disassemble the camera by
unprofessional personal.
Cautions
Do not drop the camera or subject it to physical
shock.
Do not touch senor modules with fingers. Do not place the camera in extremely hot, cold (the
operating temperature shall be -40°C to 60°C), dusty or damp locations, and do not expose it to high electromagnetic radiation.
If cleaning is necessary, use clean cloth with a bit of
ethanol and wipe it gently.
Do not aim the camera at the sun or extra bright
places.
The sensor may be burned out by a laser beam, so
when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam.
Do not expose the device to high electromagnetic
radiation or extremely hot, cold, dusty or damp environment.
To avoid heat accumulation, good ventilation is
required for the operating environment.
Warnings Follow these safeguards to prevent serious injury or death.
Cautions Follow these precautions to prevent potential injury or material damage.
Keep the camera away from liquid while in use for
non-water-proof device.
While in delivery, the camera shall be packed in its
original packing, or packing of the same texture.
Mark Description
Table 0-1 Mark Description
Mark
Description
DC Voltage
1 Introduction
1.1 Product Features
The main features are as follows:
High performance CMOS sensor IR cut filter with auto switch OSD menu with configurable parameters Auto white balance internal synchronization SMART IR mode Visible alarm PIR detection 3-axis adjustment
1.2 Overview
This manual applies to two types of the bullet camera. The overviews of each type are shown in the figures below.
1.2.1 Overview of Type I Camera
Video Cable
(TVI)
Power Cord
Lens
Bracket
Main Body
PIR
White Light
Source
Figure 1-1 Overview of Type I Camera
1.2.2 Overview of Type II Camera
PIR
Main Body
Bracket
Video Cable
(TVI)
Power Cord
12 VDC
Lens
White Light Source
Figure 1-2 Overview of Type II Camera Installation
2 Installation
Before you start
Make sure that the device in the package is in good
condition and all the assembly parts are included.
Make sure that all the related equipment is power-off
during the installation.
Check the specification of the products for the
installation environment.
Check whether the power supply is matched with
your power output to avoid the damage.
Make sure the wall is strong enough to withstand
three times the weight of the camera, and the mount.
If the wall is cement, insert expansion bolts before
installing the camera. If the wall is wooden, use self-tapping screws to secure the camera.
If the product does not function properly, contact
your dealer or the nearest service center. Do NOT disassemble the camera for repair or maintenance by yourself.
2.1 Installation of Type I Camera
2.1.1 Ceiling/Wall Mounting without Junction Box
Steps:
1. Paste the drill template (supplied) to the place
where you want to install the camera.
2. Drill the screw holes and the cable hole (optional) in
the ceiling/wall according to the drill template.
Ø 68 mm
( 2.68" )
Ø 55 mm
( 2.17" )
Template
Side Opening
Screw Hole
Screw Hole
Screw Hole
Ø 18 mm
( 2.68" )
Figure 2-1 Drill Template
Note:
Drill the cable hole, when adopting the ceiling outlet to route the cable.
3. Attach the bracket to the ceiling/wall, and secure
the camera with supplied screws.
Figure 2-2 Fix the Camera to the Ceiling
Note:
The supplied screw package contains self-tapping
screws, and expansion bolts.
For cement wall/ceiling, expansion bolts are
required to fix the camera. For wooden wall/ceiling, self-tapping screws are required.
4. Route the cables through the cable hole, or the side
opening.
5. Connect the corresponding power cord, and video
cable.
6. Power on the camera to check whether the image
on the monitor is gotten from the optimum angle. If not, adjust the camera according to the figure below to get an optimum angle.
Pan Position [0° to 360°]
P Screw
Tilt Position [0° to 180°]
T Screw
R Screw
Rotation Position [0° to 360°]
Figure 2-3 3-axis Adjustment
1). Loosen the P screw to adjust the pan position [0°
to 360°]. Tighten the screw after completing the adjustment.
2). Loosen the T screw to adjust the tilt position [0°
to 180°]. Tighten the screw after completing the adjustment.
3). Loosen the R screw and rotate the camera [0° to
360°]. Tighten the screw after completing the adjustment.
2.1.2 Ceiling/Wall Mounting with Junction Box
Before you start:
You need to purchase a junction box separately.
Steps:
1. Paste the drill template on the ceiling/wall.
2. Drill screw holes and the cable hole in the
ceiling/wall according to the holes of the drill template.
Figure 2-4 Drill Template of Junction Box
3. Take apart the junction box, and align the screw
holes of the bullet camera with those on the Junction box’ cover.
4. Fix the camera on the junction box’s cover with
supplied screws.
Junction
Box Cover
Figure 2-5 Fix the Camera on the Junction Box’s Cover
5. Attach the junction box body to the ceiling/wall by
aligning the screw holes of the junction box.
6. Secure the junction box’s body with supplied screws
on the ceiling/wall.
Junction Box
Body
Figure 2-6 Fix the Junction Box to the Wall/Ceiling
7. Route the cables through the bottom cable hole, or
the side cable hole of the junction box.
8. Combine the junction box cover with its body.
Figure 2-7 Fix the Junction Box Cover back to its
Body
9. Repeat the step 5 and 6 of 2.1.1 Ceiling/Wall
Mounting without Junction Box to complete the installation.
2.2 Installation of Type II Camera
2.2.1 Ceiling/Wall Mounting without Junction Box
Steps:
1. Paste the drill template (supplied) to the place
where you want to install the camera.
2. Drill the screw holes according to the drill template,
and the cable hole (optional) on the ceiling.
Ø 68 mm
( 2.68" )
Ø 55 mm
( 2.17" )
Template
Side Opening
Screw Hole
Screw Hole
Screw Hole
Ø 18 mm
( 2.68" )
Figure 2-8 Drill Template
Note:
Drill the cable hole in the center of the drill template, when adopting ceiling outlet to route the cable.
3. Route the cables through the cable hole (optional)
or the side opening.
4. Fix the camera to the ceiling with supplied screws.
Figure 2-9 Fix the Camera to the Ceiling
Note:
The supplied screw package contains self-tapping
screws, and expansion bolts.
For cement wall/ceiling, expansion bolts are
required to fix the camera. For wooden wall/ceiling, self-tapping screws are required.
5. Connect the corresponding power cord, and video
cable.
6. Power on the camera to check whether the image
on the monitor is gotten from the optimum angle. If not, adjust the surveillance angle.
1
2 3
Pan Position [0° to 360°]
Tilt Position [0° to 180°]
Rotation Position [0° to 360°]
Figure 2-10 3-Axis Adjustment
1) Loosen the No.1 adjusting screw to adjust the pan
position [0° to 360°]. Tighten the No.1 adjusting screw.
2) Loosen the No.2 adjusting screw to adjust the
tilting position [0° to 180°]. Tighten the No. 2 adjusting screw.
3) Loosen the No.3 adjusting screw to adjust the
rotation position [0° to 360°]. Tighten the No.3 adjusting screw.
2.2.2 Ceiling/Wall Mounting with Junction Box
Before you start:
You need to purchase a junction box separately.
Steps:
1. Paste the drill template on the ceiling/wall.
2. Drill screw holes and the cable hole (optional) in the
ceiling/wall according to the holes of the drill template.
Figure 2-11 Drill Template
Note:
Drill the cable hole, when adopting ceiling outlet to route the cable.
3. Take apart the junction box, and align the screw
holes of the bullet camera with those on the Junction box’s cover.
4. Fix the camera on the junction box’s cover with
three supplied screws.
Junction Box
Cover
Figure 2-12 Install the Junction Box
5. Secure the junction box’s body with supplied screws
on the ceiling/wall.
6. Route the cables through the bottom cable hole, or
the side cable hole of the junction box.
7. Combine the junction box cover with its body with
supplied screws on the junction box’s cover.
Figure 2-13 Combine the Junction Box’s Cover with its
Body
8. Repeat the step 5 and 6 of 2.2.1 Ceiling/Wall
Mounting without Junction Box to complete the installation.
3 Menu Description
Purpose:
Call the menu by clicking button on the PTZ Control interface, or call the preset No.95.
Steps:
1. Connect the camera with the TVI DVR, and the
monitor, shown as the figure 3-1.
Camera
TVI DVR
Monitor
Figure 3-1 Connection
2. Power on the analog camera, TVI DVR, and the
monitor to view the image on the monitor.
3. Click PTZ Control to enter the PTZ Control interface.
4. Call the camera menu by clicking button, or call
the preset No. 95.
EXPOSURE
EXPOSURE MODE
MAIN MENU
VIDEO
SETTINGS
FUNCTIONS
EXIT
SAVE & EXIT
AGC
BACK
EXIT
CONTRAST
SHARPNESS
SATURATION
DNR
MIRROR
BACK
PIR LEVEL
BACK
EXIT
LANGUAGE
VIDEO
FORMAT
FACTORY
DEFAULT
SAVE & EXIT
WHITE
BALANCE
BRIGHTNESS
EXIT
SAVE & EXIT
WHITE LIGHT
SAVE & EXIT
DAY/NIGHT
BACK
EXIT
SAVE & EXIT
MODE
IMAGE MODE
Figure 3-2 Main Menu Overview
5. Click the direction arrow to control the camera.
1). Click up/down direction button to select the
item.
2). Click Iris + to confirm the selection.
3). Click left/right direction button to adjust the
value of the selected item.
3.1 VIDEO FORMAT
You can select the video format as 2MP@25fps , or 2MP@30fps.
3.2 LANGUAGE
Supports English, and Chinese.
3.3 EXPOSURE
EXPOSURE MODE
You can set the EXPOSURE MODE as GLOBAL, BLC, or DWDR.
GLOBAL
GLOBAL refers to the normal exposure mode which adjusts lighting distribution, variations, and non-standard processing.
BLC (Backlight Compensation)
BLC (Backlight Compensation) compensates light to the object in the front to make it clear, but this may cause the over-exposure of the background where the light is strong.
DWDR (Digital Wide Dynamic Range)
The digital wide dynamic range helps the camera provide clear images even under backlight circumstances. WDR balances the brightness level of the whole image and provides clear images with details.
AGC (Auto Gain Control)
It optimizes the clarity of the image in poor light conditions. The AGC level can be set as HIGH, MEDIUM, or LOW. Select OFF to disable the AGC function.
Note:
The noise will be amplified when the AGC is on.
3.4 DAY/NIGHT
COLOR, B&W (Black White), and AUTO are selectable for DAY and NIGHT switches.
Note:
Under the LIGHTING mode, the image is colored all the time, and there’s no DAY/NIGHT settings in the menu.
COLOR
The image is colored in day mode all the time.
B/W
The image is black and white all the time, and it is better to turn the IR LIGHT on in poor light conditions.
IR LIGHT
You can turn on/off the IR LIGHT to meet the requirements of different circumstances.
SMART IR
The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure. The SMART IR value can be adjusted from 0 to 3. The greater the value is, the more obvious effects are.
AUTO
You can turn on/off the IR LIGHT, and set the value of SMART IR in this menu.
DAY/NIGHT
MODE IR LIGHT SMART IR D-N THRESHOLD
N-D THRESHOLD
BACK EXIT SAVE&EXIT
AU TO ON 2 2
7
  
Figure 3-3 DAY NIGHT
IR LIGHT
You can turn on/off the infrared to meet the requirements of different circumstances.
SMART IR
The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure. The SMART IR value can be adjusted from 0 to 3. The greater the value is, the more obvious effects are.
D-N THRESHOLD ((Day to Night Threshold))
Day to Night Threshold is used to control the sensitivity of switching the day mode to the night mode. You can set the value from 1 to 9. The larger the value is, the more sensitive the camera is.
N-D THRESHOLD (Night to Day Threshold)
Night to Day Threshold is used to control the sensitivity of switching the night mode to the day mode. You can set the value from 1 to 9. The larger the value is, the more sensitive the camera is.
3.5 VIDEO SETTINGS
Move the cursor to VIDEO SETTINGS and click Iris+ to enter the submenu. IMAGE MODE, WHITE BALANCE,
CONTRAST, SHARPNESS, COLOR GAIN, 3 DNR, and MIRROR are adjustable.
Figure 3-4 VIDEO SETTINGS
IMAGE MODE
IMAGE MODE is used to adjust the image saturation, and you can set it as STD (Standard) or HIGH-SAT (High Saturation).
WHITE BALANCE
White balance, the white rendition function of the camera, is to adjust the color temperature according to the environment. It can remove unrealistic color casts in the image. You can set WB mode as AUTO, or MANUAL.
AUTO
Under AUTO mode, white balance is being adjusted automatically according to the color temperature of the scene illumination.
MANUAL
VIDEO SETTINGS
IMAGE MODE WHITE BALANCE BRIGHTNESS CONTRAST SHARPNESS SATURATION DNR
MIRROR BACK EXIT SAVE & EXIT
5 5 5 5
5
O F F

ST D
You can set the R GAIN/B GAIN value from 1 to 255 to adjust the shades of red/blue color of the image.
WHITE BALANCE
MODE R-GAIN B-GAIN BACK EXIT SAVE&EXIT
M A N U A L 5 5



Figure 3-5 MWB MODE
BRIGHTNESS
Brightness refers to the brightness of the image. You can set the brightness value from 1 to 9 to darken or brighten the image. The greaterr the value is, the brighter the image is.
CONTRAST
This feature enhances the difference in color and light between parts of an image. You can set the CONTRAST value from 1 to 9.
SHARPNESS
Sharpness determines the amount of detail an imaging system can reproduce. You can set the SHARPNESS value from 1 to 9.
SATURATION
Adjust this feature to change the saturation of the color. The value ranges from 1 to 9.
DNR (Digital Noise Reduction)
The DNR function can decrease the noise effect, especially when capturing moving images in poor light conditions, and delivering more accurate and sharper image. You can set the DNR value from 1 to 9.
MIRROR
OFF, H, V, and HV are selectable for mirror. OFF: The mirror function is disabled. H: The image flips 180° horizontally. V: The image flips 180° vertically. HV: The image flips 180° both horizontally and
vertically.
3.6 FUNCTIONS
3.6.1 WHITE LIGHT
The embedded white light source can be worked as the visible alarm, or the lighting.
In the WHITE LIGHT mode, you can set the mode as ALARM, LIGHTING, or OFF.
When you select the WHITE LIGHT as ALARM, you can set the parameters in the TRIGGER MODE, and the ALARM MODE to meet your needs.
TRIGGER MODE
DVR
Select the TRIGGER MODE as DVR. In this way, the alarm signal is sent from the DVR, and the camera works as the alarm detector in the process. Besides, the alarm type only supported by the DVR can also triggers the visible alarm in the camera.
CAMERA
Select the TRIGGER MODE as CAMERA, the embedded PIR module sends the alarm signal to the visible alarm in the camera, when PIR module detected the alarm source.
ALARM
In the ALARM mode, you can select the ALARM MODE as SOLID, or FLASHING.
FUNCTIONS
WHITE LIGHT
TRIGGER MODE ALARM MODE
TIME SETTING PIR LEVEL
BACK EXIT
SAVE & EXIT
AL A R M
C A M E R A SO LID
15 S
3
  
Figure 3-6 ALARM MODE
SOLID
Select the ALARM MODE as SOLID. In this way, the white light source turns on, when the PIR module received the alarm signal. In the TIME SETTING you can set the time as 5 s, 10 s, 15 s, 30 s, or 60 s, which means that the solid mode stays for the set time when the camera received one alarm signal.
Note:
The solid mode will be stayed for another set time when second alarm signal is received, and the rest can be done in the same way.
FLASHING
Select the ALARM MODE as FLASHING. In this way, the white light source flashes when the PIR module received the alarm signal.
LIGHTING
Select the LIGHTING mode, the embedded white light source turns on in poor light conditions automatically. You can set the LIGHTING MODE as SOLID or FLASHING.
SOLID
The white light source turns on in the poor light conditions.
FUNCTIONS
WHITE LIGHT LIGHTING MODE PIR LEVEL BACK EXIT
SAVE & EXIT
LIG H T IN G SO LID
3
  
Figure 3-7 SOLID
FLASHING
When you select the LIGHTING MODE as FLASHING, you can set the TRIGGER MODE as CAMER, or DVR. The white light source flashes in the poor light
conditions when receiving the alarm signal.
FUNCTIONS
WHITE LIGHT LIGHTING MODE TRIGGER MODE PIR LEVEL BACK EXIT
SAVE & EXIT
LIG H T IN G FL AS H IN G
C A M ER A 3

 
Figure 3-8 FLASHING
TRIGGER MODE
DVR
Select the TRIGGER MODE as DVR. In this way, the alarm signal is sent from the DVR, and the camera works as the alarm detector in the process. Besides, the
alarm type only supported by the DVR can also triggers the visible alarm in the camera.
CAMERA
Select the TRIGGER MODE as CAMERA, the embedded PIR module sends the alarm signal to the visible alarm in the camera, when PIR module detected the alarm source.
Note:
Type I camera do not have LIGHTING mode. Under the LIGHTING mode, the image is colored all
the time, and there’s no DAY NIGHT settings in the menu.
OFF
Select OFF to give up this function.
3.6.2 PIR LEVEL
Adjust the sensitivity of the PIR module, and the greater the value is, the more sensitive the PIR module is.
3.7 FACTORY DEFAULT
Reset all the settings to the factory default.
3.8 EXIT
Move the cursor to EXIT and click Iris+ to exit the menu.
3.9 SAVE & EXIT
Move the cursor to SAVE & EXIT and click Iris+ to save the settings, and exit the menu.
UD10293B
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use