TurboHD
DS-2CE11H0T-PIRL
Bullet Camera
User Manual
Thank you for purchasing our product. If there are any questions, or requests, do
not hesitate to contact the dealer.
This manual may contain several technical incorrect places or printing errors, and
the content is subject to change without notice. Updates will be added to new
versions of this manual. We will readily improve or update the products or
procedures described in the manual.
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
1 Regulatory Information
1.1 FCC Information
Please take attention that changes or modification not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
FCC Compliance: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
1.2 FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
1.3 EU Conformity Statement
This product and, if applicable, the supplied accessories too are marked
standards listed under the Low Voltage Directive 2014/35/EU, the EMC Directive
2014/30/EU, the RoHS Directive 2011/65/EU.
collection points. For more information see: www.recyclethis.info.
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the
battery to your supplier or to a designated collection point. For more information
see: www.recyclethis.info.
1.4 Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
1.5 Warning
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
1.6 Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions.”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are
neglected.
with “CE” and comply therefore with the applicable harmonized European
2012/19/EU (WEEE Directive): Products marked with this symbol cannot
be disposed of as unsorted municipal waste in the European Union. For
proper recycling, return this product to your local supplier upon the
purchase of equivalent new equipment, or dispose of it at designated
2006/66/EC (Battery Directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
See the product documentation for specific battery information. The
battery is marked with this symbol, which may include lettering to
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
Warnings
Follow
Cautions
Follow these
these safeguards to
precautions to prevent
prevent serious injury
potential injury or
or death.
material damage.
1.7 Warnings
• In the use of the device, you must be in strict compliance with the electrical
safety regulations of the nation and region.
• Input voltage should meet both the SELV (Safety Extra Low Voltage) and the
Limited Power Source with 12 VDC according to the IEC60950-1 standard. Refer
to technical specifications for detailed information.
• Do not connect multiple devices to one power adapter to avoid overheating or
a fire hazard caused by overload.
• Make sure that the plug is firmly connected to the power socket.
• Make sure that the device is firmly fixed if wall mounting or ceiling mounting is
adopted.
• If smoke, odor, or noise rise from the device, turn off the power at once and
unplug the power cord, and then contact the service center.
• Never attempt to disassemble the camera by unprofessional personal.
1.8 Cautions
• Do not drop the camera or subject it to physical shock.
• Do not touch sensor modules with fingers.
• Do not place the camera in extremely hot, cold (the operating temperature shall
be -40° to 60° C), dusty, or damp locations, and do not expose it to high
electromagnetic radiation.
• If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it
gently.
• Do not aim the camera at the sun or extra bright places.
• The sensor may be burned out by a laser beam, so when any laser equipment is
in use, make sure that the surface of the sensor will not be exposed to the laser
beam.
• Do not expose the device to high electromagnetic radiation or extremely hot,
cold, dusty, or damp environment.
• To avoid heat accumulation, good ventilation is required for the operating
environment.
• Keep the camera away from liquid while in use for non-waterproof device.
• While in delivery, the camera shall be packed in its original packing or packing of
the same texture.
1.9 Mark Description
Table 0-1 Mark Description
Mark Description
DC Voltage
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
2 Introduction
2.1 Product Features
The main features are as follows:
• High performance CMOS sensor
• IR cut filter with auto switch
• OSD menu with configurable parameters
• Auto white balance
• Internal synchronization
• SMART IR mode
• Visible alarm
• PIR detection
• 3-axis adjustment
2.2 Overview
2.2.1 Camera Overview
Figure 1, Camera Overview
3 Installation
Before you start
•
Make sure that the device in the package is in good condition and all the
assembly parts are included.
•
Make sure that all the related equipment is powered off during the
installation.
•
Check the specification of the products for the installation environment.
•
Check whether the power supply matches your power output to avoid
damage.
•
Make sure the wall is strong enough to withstand three times the weight
of the camera and the mount.
•
If the wall is cement, insert expansion bolts before installing the camera. If
the wall is wood, use self-tapping screws to secure the camera.
•
If the product does not function properly, contact your dealer or the
nearest service center. Do NOT disassemble the camera for repair or
maintenance yourself.
3.1 Camera Installation
3.1.1 Ceiling/Wall Mounting without Junction Box
Steps:
1. Paste the drill template (supplied) to where you want to install the
camera.
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
2. Drill the screw holes and the cable hole (optional) in the
ceiling/wall according to the drill template.
Figure 2, Drill Template
Note:
Drill a cable hole when using the ceiling outlet to route the cable.
Figure 3, Fix the Camera to the Ceiling
3. Attach the bracket to the ceiling/wall, and secure the camera with
supplied screws.
Note:
•
The supplied screw package contains self-tapping screws and
expansion bolts.
•
For cement wall/ceiling, expansion bolts are required to fix the
camera. For wood wall/ceiling, self-tapping screws are required.
4. Route the cables through the cable hole or the side opening.
5. Connect the corresponding power cord and video cable.
6. Power on the camera to check whether the image on the monitor
is at an optimum angle. If not, adjust the camera according to the
figure below to get an optimum angle.
Figure 4, 3-axis Adjustment
1). Loosen the P screw to adjust the pan position [0° to 360°].
Tighten the screw after completing the adjustment.
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
2). Loosen the T screw to adjust the tilt position [0° to 180°].
Tighten the screw after completing the adjustment.
3). Loosen the R screw and rotate the camera [0° to 360°].
Tighten the screw after completing the adjustment.
3.1.2 Ceiling/Wall Mounting with Junction Box
Before you start:
You need to purchase a junction box separately.
Steps:
1. Paste the drill template on the ceiling/wall.
2. Drill screw holes and the cable hole in the ceiling/wall according
to the holes of the drill template.
Figure 5, Drill Template of Junction Box
3. Take apart the junction box and align the screw holes of the bullet
camera with those on the junction box cover.
4. Fix the camera on the junction box’s cover with supplied screws.
Figure 6, Fix the Camera on the Junction Box Cover
5. Attach the junction box body to the ceiling/wall by aligning the
screw holes of the junction box.
6. Secure the junction box’s body with supplied screws on the
ceiling/wall.
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
Figure 7, Fix the Junction Box to the Wall/Ceiling
7. Route the cables through the bottom cable hole or the side cable
hole of the junction box.
8. Combine the junction box cover with its body.
Figure 8, Fix the Junction Box Cover back to its Body
9. Repeat step 5 and 6 of 2.1.1 Ceiling/Wall Mounting without
Junction Box to complete the installation.
4 Menu Description
Purpose:
Call the menu by clicking the button on the PTZ Control interface, or call
the preset no.95.
Steps:
1. Connect the camera to the TVI DVR and the monitor, as shown below.
Figure 9, Connection
2. Power on the analog camera, TVI DVR, and the monitor to view the image
on the monitor.
3. Click PTZ Control to enter the PTZ Control interface.
4. Call the camera menu by clicking the button or call the preset no. 95.
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
Figure 10, Main Menu Overview
5. Click the direction arrow to control the camera.
1). Click Up/Down direction button to select the item.
2). Click Iris+ to confirm the selection.
3). Click Left/Right direction button to adjust the value of the selected
item.
4.1 VIDEO FORMAT
You can set the video format to 5 MP @ 20 fps, 4 MP @ 25 fps, 4 MP @ 30
fps, 2 MP @ 25 fps, or 2 MP @ 30 fps.
4.2 EXPOSURE
4.2.1 EXPOSURE MODE
You can set the EXPOSURE MODE to GLOBAL, BLC, or DWDR.
• GLOBAL
GLOBAL refers to the normal exposure mode, which adjusts lighting
distribution, variations, and non-standard processing.
• BLC (Backlight Compensation)
BLC (Backlight Compensation) compensates light to the object in the
front to make it clear, but this may cause overexposure of the
background where the light is strong.
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
• DWDR (Digital Wide Dynamic Range)
The digital wide dynamic range helps the camera provide clear
images even under backlight circumstances. WDR balances the
brightness level of the whole image and provides clear images with
details.
4.2.2 AGC (Auto Gain Control)
It optimizes the clarity of the image in poor light conditions. The AGC
level can be set as HIGH, MEDIUM, or LOW. Select OFF to disable the
AGC function.
Note:
The noise will be amplified when the AGC is on.
4.2.3 DAY/NIGHT
COLOR, B&W (Black White), and AUTO are selectable for DAY and
NIGHT switches.
Note:
Under the LIGHTING mode, the image is in color all the time, and
there’s no DAY/NIGHT setting in the menu.
• COLOR
The image is in color in day mode all the time.
• B/W
The image is black and white all the time. Turning the IR LIGHT on in
poor light conditions will improve the image.
• AUTO
Figure 11, DAY NIGHT
You can turn on/off the IR LIGHT and set the SMART IR value in this
menu.
˗ IR LIGHT
You can turn on/off the IR LIGHT to meet the circumstances.
˗ SMART IR
The Smart IR function adjusts the light to its most suitable
intensity and prevents the image from overexposure. The SMART
IR value can be adjusted from 0 to 3. The greater the value, the
more obvious the effect
• D-N THRESHOLD (Day to Night Threshold)
Day to Night Threshold controls the sensitivity of switching the day
mode to night mode. You can set the value from 1 to 9. The larger
the value, the more sensitive the camera.
• N-D THRESHOLD (Night to Day Threshold)
Night to Day Threshold controls the sensitivity of switching the night
mode to day mode. You can set the value from 1 to 9. The larger the
value, the more sensitive the camera.
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
.
4.3 VIDEO SETTINGS
Move the cursor to VIDEO SETTINGS and click Iris+ to enter the submenu.
CONTRAST, SHARPNESS, COLOR GAIN, 3 DNR, and MIRROR are adjustable.
Figure 12, VIDEO SETTING
• WHITE BALANCE
White balance, the white rendition function of the camera, adjusts
the color temperature according to the environment. It can remove
unrealistic color casts in the image. You can set WHITE BALANCE
mode to AUTO or MANUAL.
˗
AUTO
Under AUTO mode, white balance is adjusted automatically
according to the color temperature of the scene illumination.
˗ MANUAL
You can set the R-GAIN/B-GAIN value from 1 to 255 to adjust the
shades of red/blue color of the image.
Figure 13, MWB MODE
• BRIGHTNESS
Brightness refers to the brightness of the image. You can set the
brightness value from 1 to 9 to darken or brighten the image. The
greater the value, the brighter the image.
• CONTRAST
This feature enhances the difference in color and light between
parts of an image. You can set the CONTRAST value from 1 to 9.
• SHARPNESS
Sharpness determines the amount of detail the imaging system can
reproduce. You can set the SHARPNESS value from 1 to 9.
• SATURATION
Adjust this feature to change the saturation of the color. The value
ranges from 1 to 9.
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
• DNR (Digital Noise Reduction)
The DNR function can decrease the noise effect, especially when
capturing moving images in poor light conditions, and delivers more
accurate and sharper images. You can set the DNR value from 1 to
9.
• MIRROR
OFF, H, V, and HV are selectable for mirror.
OFF: The mirror function is disabled.
H: The image flips 180° horizontally.
V: The image flips 180° vertically.
HV: The image flips 180° both horizontally and vertically.
4.4 FUNCTIONS
• WHITE LIGHT
The embedded white light source can work as an visible alarm or lighting.
In the WHITE LIGHT mode, you can set the mode to ALARM, LIGHTING, or
OFF.
When you set the WHITE LIGHT to ALARM, you can set the Parameters in
the TRIGGER MODE and the ALARM MODE to meet your needs.
˗ TRIGGER MODE
>
DVR
Set the TRIGGER MODE to DVR. In this way, the alarm signal is sent
from the DVR and the camera works as the alarm detector in the
process. Besides, the alarm type only supported by the DVR can also
trigger the visible alarm in the camera.
> CAMERA
Set the TRIGGER MODE to CAMERA, the embedded PIR module
sends the alarm signal to the visible alarm in the camera when the
PIR module detects the alarm source.
˗ ALARM
In the ALARM mode, you can set the ALARM MODE to SOLID or
FLASHING.
Figure 14, ALARM MODE
> SOLID
Set the ALARM MODE to SOLID. In this way, the white light source
turns on when the PIR module receives the alarm signal.
In the TIME SETTING you can set the time to 5s, 10s, 15s, 30s, or
60s, which means that the solid mode stays for the set time when
the camera receives one alarm signal.
Note:
The solid mode will stay for another set time when a second alarm
signal is received, and the rest can be done in the same way.
> FLASHING
Set the ALARM MODE to FLASHING. In this way, the white light
source flashes when the PIR module receives the alarm signal.
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
• LIGHTING
Select the LIGHTING mode, the embedded white light source turns on in
poor light conditions automatically. You can set the LIGHTING MODE to
SOLID or FLASHING.
˗ SOLID
The white light source turns on in poor lighting conditions.
Figure 15, SOLID
˗ FLASHING
When you set the LIGHTING MODE to FLASHING, you can set the
TRIGGER MODE to CAMERA or DVR.
The white light source flashes in poor lighting conditions when
receiving the alarm signal.
*
TRIGGER MODE
o
DVR
Set the TRIGGER MODE to DVR. In this way, the alarm signal is
sent from the DVR, and the camera works as an alarm detector
in the process. Besides, the alarm type only supported by the
DVR can also trigger the visible alarm in the camera.
Figure 16, FLASHING
o CAMERA
Set the TRIGGER MODE to CAMERA, the embedded PIR module
sends the alarm signal to the visible alarm in the camera when
the PIR module detects the alarm source.
˗ OFF
Select OFF to disable this function.
• PIR LEVEL
Adjust the sensitivity of the PIR module. The higher the value, the more
sensitive the PIR module.
• FACTORY DEFAULT
Reset all the settings to the factory defaults.
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
• EXIT
Move the cursor to EXIT and click Iris+ to exit the menu.
• SAVE & EXIT
Move the cursor to SAVE & EXIT and click Iris+ to save the settings and
exit the menu.
UM D-2CE11H0T-PIRL 2018 Hikvision USA Inc.
Loading...