0
ANPR Network Bullet Camera
Quick Start Guide
UD04143B
Network Bullet Camera·Quick Start Guide
1
1
Quick Start Guide
COPYRIGHT © 2016 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures,
graphs are the properties of Hangzhou Hikvision Digital Technology
Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
This user manual (hereinafter referred to be “the Manual”) cannot
be reproduced, changed, translated, or distributed, partially or
wholly, by any means, without the prior written permission of
Hikvision. Unless otherwise stipulated, Hikvision does not make any
warranties, guarantees or representations, express or implied,
regarding to the Manual.
About this Manual
This Manual is applicable to 4Axx Network Camera.
The Manual includes instructions for using and managing the
product. Pictures, charts, images and all other information
hereinafter are for description and explanation only. The
information contained in the Manual is subject to change, without
notice, due to firmware updates or other reasons. Please find the
latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the
properties of Hikvision in various jurisdictions. Other trademarks and
logos mentioned below are the properties of their respective
owners.
Network Bullet Camera·Quick Start Guide
2
2
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND
FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,
SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE
LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR
LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF
THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL
NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS
PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
Network Bullet Camera·Quick Start Guide
3
3
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
Network Bullet Camera·Quick Start Guide
4
4
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the EMC Directive 2014/30/EU, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards
requirements.
Network Bullet Camera·Quick Start Guide
5
5
Warning
This is a class A product. In a domestic environment this product may
cause radio inter-ference in which case the user may be required to
take adequate measures.
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
● Proper configuration of all passwords and other security
settings is the responsibility of the installer and/or end-user.
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these precautions
to prevent potential injury or
material damage.
Network Bullet Camera·Quick Start Guide
6
6
● In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
● Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 12 VDC according
to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
● Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
● Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
● If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the service center.
Cautions
● Make sure the power supply voltage is correct before using the
camera.
● Do not drop the camera or subject it to physical shock.
● Do not touch sensor modules with fingers. If cleaning is
necessary, use clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
● Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
Network Bullet Camera·Quick Start Guide
7
7
malfunction), and affect the endurance of sensor at the same
time.
● The sensor may be burned out by a laser beam, so when any
laser equipment is in using, make sure that the surface of
sensor will not be exposed to the laser beam.
● Do not place the camera in extremely hot, cold (the operating
temperature shall be-30°C to +60°C , or -40°C to +60°C if the
camera model has an “H” in its suffix), dusty or damp locations,
and do not expose it to high electromagnetic radiation.
● To avoid heat accumulation, good ventilation is required for
operating environment.
● Keep the camera away from liquid while in use.
● While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
● Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average enduring time. The average time
varies because of differences between operating environment
and using history, so regular checking is recommended for all
the users. Please contact with your dealer for more details.
● Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
● If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume any
Network Bullet Camera·Quick Start Guide
8
8
responsibility for problems caused by unauthorized repair or
maintenance.)
Network Bullet Camera·Quick Start Guide
9
9
Table of Contents
1 Appearance Description ............................................................... 10
Type I ............................................................................ 10 1.1
Type II ........................................................................... 11 1.2
2 Installation .................................................................................... 14
Memory Card Installation .............................................. 14 2.1
Direct Mounting ............................................................ 15 2.2
Mounting with a Junction Box ....................................... 18 2.3
Mounting with a Gang Box ............................................ 20 2.4
Network Cable Water-proof Jacket Installation (Optional)21 2.5
3 Setting the Network Camera over the LAN .................................. 24
Wiring ........................................................................... 24 3.1
Activating the Camera ................................................... 25 3.2
Activation via Web Browser ................................ 25 3.2.1
Activation via SADP Software ............................. 27 3.2.2
Modifying the IP Address .............................................. 28 3.3
4 Accessing via Web Browser .......................................................... 30
0504031061226
Network Bullet Camera·Quick Start Guide
10
10
1 Appearance Description
This camera series has two appearance types.
Type I 1.1
The overview of the Type I bullet camera is shown below.
8
1
DC
12
V
ALARM
IN
G
1
A
1
B
V
I
E
O
D
2
3
4
5
6
10
9
7
11
12
13
Overview of Type I Camera Figure 1-1
Description of Type I Camera Table 1-1
No.
Description
1
Photoresistor
2
Lens
3
Sun Shield
Network Bullet Camera·Quick Start Guide
11
11
No.
Description
4
3-axis Bracket
5
RJ45 Network Interface
6
Power Cord (12 VDC)
7*
Alarm Input and Output Interface
8
BNC
9*
Audio Output Interface
10*
Audio Input Interface
11
Reset Button
12
Memory Card Slot
13
Serial Port
Note:
The items marked with the "*" are only supported by certain
camera models.
Press RESET about 10s when the camera is powering on or
rebooting to restore the default settings, including the user name,
password, IP address, port No., etc.
Type II 1.2
The overview of the Type II bullet camera is shown below.
Network Bullet Camera·Quick Start Guide
12
12
1
2
3 4
11
12
13
5
6
7
VIEOD
8
9
10
Overview of Type II Camera Figure 1-2
Description of Type II Camera Table 1-2
No.
Description
1
Photoresistor
2
Lens
3
Sun Shield
4
3-axis Bracket
5
RJ45 Network Interface
6
Power Cord (12 VDC)
7
Alarm Input and Output Interface
8
BNC
Network Bullet Camera·Quick Start Guide
13
13
No.
Description
9
Audio Output Interface
10
Audio Input Interface
11
Reset Button
12
Memory Card Slot
13
Serial Port
Note:
The items marked with the "*" are only supported by certain
camera models.
Press RESET about 10s when the camera is powering on or
rebooting to restore the default settings, including the user name,
password, IP address, port No., etc.
Network Bullet Camera·Quick Start Guide
14
14
2 Installation
Before you start:
● Make sure the device in the package is in good condition and all
the assembly parts are included.
● The standard power supply is 12 VDC, please make sure your
power supply matches with your camera.
● Make sure all the related equipment is power-off during the
installation.
● Check the specification of the products for the installation
environment.
● Make sure that the wall is strong enough to withstand four
times the weight of the camera and the bracket.
For the camera that supports IR and white light supplement, you are
required to pay attention to the following precautions to prevent
IR/white light reflection:
● Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back into
the lens causing reflection.
Memory Card Installation 2.1
This series of camera supports memory card installation. Follow the
steps below to mount and unmount the memory card.
1. Loosen the two lock screws and remove the slot cover.
Network Bullet Camera·Quick Start Guide
15
15
Slot
Cover
Figure 2-1 Remove Card Cover
2. Insert the memory card into the memory card slot.
Memory
Card
Figure 2-2 Insert the Card
3. (Optional) To unmount the memory card, push to get it ejected.
4. Screw the slot cover back to the camera.
Direct Mounting 2.2
The camera series shares similar mounting steps. We take Type I
camera as the example in demonstration.
Network Bullet Camera·Quick Start Guide
16
16
Steps:
1. Drill 4 screw holes (hole 1 on drill template) and the cable hole in
the ceiling/wall.
Drill Template Figure 2-3
2. Fix the camera to the wall/ceiling with the supplied screws.
Note:
Insert the expansion screws first if the camera is mounted to the
cement wall/ceiling. Use the self-tapping screws directly if camera
is mounted to the wooden wall/ceiling.
Network Bullet Camera·Quick Start Guide
17
17
Wall
Ceiling
Install the Camera Figure 2-4
3. Adjust the surveillance angle.
1). Loosen No.1 lock screw to adjust the tilt angle [0 ° to 100°].
2). Loosen No.2 lock screw to adjust the pan angle [0° to 360°].
3). Loosen No.3 lock screw to rotate the camera [0° to 360°].
4). Tighten the lock screws.
Note:
A wrench is supplied to loosen and tighten the screws.
0°
~
100°
0°
~
360°
0°
~
360°
1
2
3
Adjust the Surveillance Angle Figure 2-5
Network Bullet Camera·Quick Start Guide
18
18
Supplied Wrench Figure 2-6
4. (Optional) Install the water-proof jacket for network interface.
Refer to Section 2.5 Network Cable Water-proof Jacket Installation
(Optional).
Note:
It is recommended to adopt the water-proof jacket (supplied) for
the network interface, especially when the camera is installed
outdoor.
Mounting with a Junction Box 2.3
Before You Start:
Junction box is not included in package. You need to prepare one in
advance if you adopt this mounting type. The shown junction box is
for demonstration.
Network Bullet Camera·Quick Start Guide
19
19
Dimension of Junction Box Figure 2-7
Steps:
1. Paste the drill template to desired mounting place. Drill the screw
hole and cable hole according to the supplied drill template
(shown as Figure 2-3).
2. Align the screw holes of the junction box to the drill template, and
fix the junction box to the wall with screws.
3. Hang the camera with the safety rope of junction box.
4. Route the cables.
5. Fix the camera to the junction box with screws.
6. Adjust the surveillance angle according to step 3 in Section2.2.
7. Install the water-proof jacket according to Section 2.5.
Network Bullet Camera·Quick Start Guide
20
20
Drill Template
Safety Rope
Junction Box
Installation with a Junction Box Figure 2-8
Mounting with a Gang Box 2.4
Before You Start:
An adapter plate should be purchased separately if you mount the
camera to a gang box.
Steps:
1. Install the adapter plate to the gang box.
2. Route the cables.
3. Fix the camera to the adapter plate with screws.
4. Adjust the surveillance angle according to step 3 in Section 2.2.
5. Install the water-proof jacket according to Section 2.5.
Network Bullet Camera·Quick Start Guide
21
21
Adapter Plate
Figure 2-9 Installation with a Gang Box
Network Cable Water-proof Jacket 2.5
Installation (Optional)
Purpose:
If the camera is installed outdoor, you can adapt the water-proof
accessory for the network cable after the camera is secured on the
installation surface.
①
②
③
④
⑤
⑥ ⑦
Figure 2-10 Water-proof Accessory Components
Network Bullet Camera·Quick Start Guide
22
22
Table 2-1 Components
No.
Components
1
Camera’s Network Interface Socket
2
O-Type Gasket
3
Network Plug
4
Waterproof Endcap
5
Waterproof Rubber Gasket
6
Lock Nut
7
Network Cable from Router/Switch
Steps:
Feed the plugless network cable ⑦ through the lock nut ⑥, 1.
waterproof rubber gasket ⑤ (rubber gasket inset ridge must
face waterproof endcap), and the water-proof endcap ④ in
order.
Crimp an RJ-45 network plug ③onto the end of the cable, 2.
taking care to insert the twisted pairs of wires in correct order.
Place the O-type gasket ② onto the end of the camera’s 3.
network interface socket ①.
Insert the network plug ③ into the camera’s network interface 4.
socket①.
Network Bullet Camera·Quick Start Guide
23
23
Insert the water-proof rubber gasket ⑤ into the waterproof 5.
endcap ④, and secure lock nut ⑥ with the water-proof
endcap ④.
Align the snap on the water-proof endcap ④ with the notch on 6.
the camera’s network interface socket ①, and then secure the
water-proof endcap ④ to the camera’s network interface
socket ① to finish installation.
Camera
Switch/Router
Align the snap and notch.
i. Insert ⑤ into ④.
ii. Secure ⑥ with ④.
Water-proof Accessory Installation Figure 2-11
Network Bullet Camera·Quick Start Guide
24
24
3 Setting the Network Camera over the
LAN
Note:
You shall acknowledge that the use of the product with Internet
access might be under network security risks. For avoidance of any
network attacks and information leakage, please strengthen your
own protection. If the product does not work properly, please
contact with your dealer or the nearest service center.
Wiring 3.1
Please connect to the camera to the network according to the
following figures
Network Cable
or
Network Camera
Computer
Connecting Directly Figure 3-1
Network Cable
Network Cable
or
or
Network Camera Computer
Connecting via a Switch or a Router Figure 3-2
Network Bullet Camera·Quick Start Guide
25
25
Activating the Camera 3.2
You are required to activate the camera first by setting a strong
password for it before you can use the camera.
Activation via Web Browser, Activation via SADP, and Activation via
Client Software are all supported. We will take activation via SADP
software and Activation via Web Browser as examples to introduce
the camera activation. Please refer to the User Manual of Network
Camera for Activation via Client Software.
Activation via Web Browser 3.2.1
Steps:
1. Power on the camera, and connect the camera to the network.
2. Input the IP address into the address bar of the web browser, and
click Enter to enter the activation interface.
Notes:
The default IP address of the camera is 192.168.1.64.
For the camera enables the DHCP by default, you need to
activate the camera via SADP software and search the IP
address.
Network Bullet Camera·Quick Start Guide
26
26
Activation Interface(Web) Figure 3-3
3. Create a password and input the password into the password
field.
STRONG PASSWORD RECOMMENDED– We highly
recommend you create a strong password of your own
choosing (using a minimum of 8 characters, including
upper case letters, lower case letters, numbers, and
special characters) in order to increase the security of
your product. And we recommend you reset your
password regularly, especially in the high security
system, resetting the password monthly or weekly can
better protect your product.
4. Confirm the password.
5. Click OK to save the password and enter the live view interface.
Network Bullet Camera·Quick Start Guide
27
27
Activation via SADP Software 3.2.2
SADP software is used for detecting the online device, activating the
camera, and resetting the password.
Get the SADP software from the supplied disk or the official website,
and install the SADP according to the prompts. Follow the steps to
activate the camera, please refer to the User Manual of Network
Camera for other two activation methods.
Steps:
1. Run the SADP software to search the online devices.
2. Check the device status from the device list, and select the
inactive device.
SADP Interface Figure 3-4
Network Bullet Camera·Quick Start Guide
28
28
Note:
The SADP software supports activating the camera in batch. Please
refer to the user manual of SADP software for details.
3. Create a password and input the password in the password field,
and confirm the password.
STRONG PASSWORD RECOMMENDED– We highly
recommend you create a strong password of your own
choosing (using a minimum of 8 characters, including
upper case letters, lower case letters, numbers, and
special characters) in order to increase the security of
your product. And we recommend you reset your
password regularly, especially in the high security
system, resetting the password monthly or weekly can
better protect your product.
4. Click OK to save the password.
You can check whether the activation is completed on the popup
window. If activation failed, please make sure that the password
meets the requirement and try again.
Modifying the IP Address 3.3
Purpose:
To view and configure the camera via LAN (Local Area Network), you
need to connect the network camera in the same subnet with your
PC. Then, install the SADP software or client software to search and
change the IP of network camera. We will take modifying the IP
Address via SADP software as an example to introduce the IP address
modification.
Network Bullet Camera·Quick Start Guide
29
29
Steps:
1. Run the SADP software.
2. Select an active device.
Note:
Please refer to Chapter 3.2 to activate the camera if the camera is
inactive.
3. Change the device IP address to the same subnet with your
computer by either modifying the IP address manually or checking
the checkbox of Enable DHCP.
Modify the IP Address Figure 3-5
4. Input the password to activate your IP address modification.
The batch IP address modification is supported by the SADP; please
refer to the User Manual of SADP for details.
Network Bullet Camera·Quick Start Guide
30
30
4 Accessing via Web Browser
System Requirement:
Operating System: Microsoft Windows XP SP1 and above version
CPU: 2.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 8.0 and above version, Apple Safari
5.0.2 and above version, Mozilla Firefox 5.0 and above version and
Google Chrome 18 and above version
Steps:
1. Open the web browser.
2. In the browser address bar, input the IP address of the network
camera, and press the Enter key to enter the login interface.
Note:
The default IP address is 192.168.1.64.
If the camera is not activated, please activate the camera first
according to Chapter 3.2.
3. Input the user name and password.
The admin user should configure the device accounts and
user/operator permissions properly. Delete the unnecessary
accounts and user/operator permissions.
Note:
The device IP address gets locked if the admin user performs 7
failed password attempts (5 attempts for the user/operator).
Network Bullet Camera·Quick Start Guide
31
31
4. Click Login.
Login Interface Figure 4-1
5. Install the plug-in before viewing the live video and managing the
camera. Please follow the installation prompts to install the
plug-in.
Note:
You may have to close the web browser to finish the plug-in
installation.
Download Plug-in Figure 4-2
6. Reopen the web browser after the installation of the plug-in and
repeat steps 2 to 4 to login.
Note:
For detailed instructions of further configuration, please refer to
the user manual of network camera.
0
Loading...