HID V100, V200, V300, V1000, V2000 Installation Guide

15370 Barranca Parkway

Irvine, CA 92618

USA

VertX®

V100, V200, V300, V1000, and V2000

Installation Guide

December 2010

Document Number: 6080-901 Rev G.2

VertX Installation Guide

Introduction

HID’s VertX open platform is flexible and scalable to permit economic and high performance access control solutions for a wide range of applications. The VertX units interconnect through different sub-networks and protocols to a standard TCP/IP network with the capability of a variety of applications.

For example, the VertX Access Controllers are a cost-effective method for two-way communication using Ethernet between a computer and a V1000 or V2000. In addition, the V1000 can communicate through a RS-232 serial port and a multi-drop RS-485.

Parts List

Description Quantity

VertX™ units (one of the following):

V2000 (Reader Interface / Access Controller)

V1000 (Access Controller)

V100 (Door/Reader Interface)

V200 (Input Monitor Interface)

V300 (Output Control Interface)

Note: Each VertX unit has a plastic base and is covered with a Plastic or Mylar cover.

- Lithium Battery (V1000 / V2000) 1

- Mounting screws 4

- 2.2K EOL resistors 8 ea V1000/V2000

- Quick Installation Guide 1

- Installation Wiring Diagram Example 1

Note: One or more VertX Interface panels are required when installing a V1000 controller. Note: A modem and RS-232 Serial modem cable must be purchased separately, if your installation includes a

modem.

1 V2000

or

1 V1000 and any combination of (up to 32) interface panels.

4 ea V100-Series

Product Specifications

Description Specification

Power Supply 12-16VDC

Maximum Current at 12VDC per unit 1 Amp

Average operating current at 12VDC

Operating temperature range 32°-122°F (0°-50°C)

Humidity 5% to 95% non-condensing

December 2010 Page 3 of 24

V1000 -210mA V2000 - 625mA (with two R40 iCLASS Readers) V100 - 450mA (with two R40 iCLASS Readers)

V200 - 60mA

V300 - 75mA

VertX Installation Guide

Cable Specifications

Cable Type Length Specification

RS-485 * 4000 feet (1220 m) to host

15 feet (4.57 m) for RS-232

RS-232

Serial modem cable

6 inch (15.24 cm) adapter

Input Circuits * 500 feet (150 m)

Output Circuits * 500 feet (150 m)

Wiegand

500 feet (150 m) to reader ALPHA 1299C, 22AWG, 9-conductor, stranded, overall shield.

Ethernet 328 feet (100 m) Cat5, Cat5E, and Cat6

Power Supply

+12 VDC IN

---- Refer to your Power Supply Installation Guide.

* Minimum wire gauge depends on cable length and current requirements.

Using Belden 3105A, 22AWG twisted pair, shielded 100 cable, or equivalent.

Use any RS-232 Serial modem cable specified by the modem manufacturer.

HID Serial Adapter cable, P/N 70007

2-conductor, shielded, using ALPHA 1292C (22AWG) or Alpha 2421C (18AWG), or equivalent.

2-conductor, using ALPHA 1172C (22AWG) or Alpha 1897C (18AWG), or equivalent.

Fewer conductors needed if all control lines are not used.

December 2010 Page 4 of 24

VertX Installation Guide

Overview

The following outlines what is required to install VertX controllers and panels.

December 2010 Page 5 of 24

VertX Installation Guide

Step 1 Connect

1.1 What you need before getting started

Prior to starting the installation, completely read this guide. Reference the Configuration Checklist

instructions.

CAUTION: VertX controllers and panels are sensitive to Electrostatic Discharges (ESD). Observe precautions while handling the circuit board assembly by using proper grounding straps and handling precautions at all times.

1.2 V1000 or V2000

1. Verify the battery jumper is installed in the ON position (or OUT position on old covers), P15 connector (V1000).

2. If installing a V1000 - Verify the termination jumper is in

the Out position when there are no panels attached to

the port. If there are downstream interface panels

attached then the termination jumper should be in the In position. The V1000 is shipped with jumpers in the Out

positions

, page 21, and gather the information before proceeding with these

1.3 Mounting Instructions

1. The controllers and interface panels should always be mounted in a secure area.

2. Mount using the four mounting screws (provided) or other appropriate fasteners. Place the fasteners in the corner holes of the base.

3. The VertX devices can be stacked with or without the cover. Do not remove the plastic base. Make sure you position the VertX devices in such a way as to provide room for wiring, air-flow and cable runs.

1.4 V100, V200, or V300

1. If the V100-Series panel will be attached to the end of the

RS-485 bus, install a terminating jumper to the In position

on the termination resistor pins, P8 on the cover (P10 on the PCB) of the V100, V200 and V300.

2. If the V100-Series panel is being installed as part of an array, or in a third party enclosure, follow the directions provided by the Integrator or Dealer.

Terminating Jumper

December 2010 Page 6 of 24

VertX Installation Guide

1.5 Wiring VertX

CAUTION: Connectors on the VertX devices are positioned to be mirror images and are not interchangeable once the installation is complete. Therefore, you cannot unplug a connector from one side and plug it into the corresponding connector on the other side.

1. Network Connection: Connect the VertX V1000/V2000 to the network using a standard Cat5 network patch cable. Connect one end of the Cat5 network patch cable to the J1 (RJ-45) connector

on the V1000/V2000 and the other end to the network connection point (network jack, hub, switch, or router) on your site.

2. Serial (RS-232) Adapter cable (P/N 70007)

The Serial Adapter cable is a six inch adapter that converts the 9 pin MTA header to a standard DB-9 male connector. This adapter is to be utilized for attaching a standard RS-232 serial modem cable (not included) to the VertX controller. This will allow one of the approved external modems (listed in 1.6.1 Modem Setup Requirements, page 12) to be attached to the VertX V1000.

The table shows the P17 pin settings.

Pin # P17

1 DCD

2 RX

3 TX

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

9 RI

3. Power and Alarm input connections (All VertX units): Connect power by providing 12VDC to the P7 connector. +12VDC goes to Pin 1 and ground to Pin 2. Batt

Fail, AC Fail, and Tamper switch inputs are wired as shown in the table. Connect the Bat Fail and AC Fail inputs to battery low/failure and AC failure contacts provided on the power supply. Connect the Tamper input to a tamper switch on the enclosure.

Pin # P7

1 +12VDC

2 Ground

3 Bat Fail -

4 Bat Fail +

5 AC Fail -

6 AC Fail +

7 Tamper -

8 Tamper +

December 2010 Page 7 of 24

VertX Installation Guide

4 Reader Connections (V2000 or V100):

Connect Wiegand or clock-and-data interfaces to a V2000 or V100 using the connection table shown. You can connect up to 10 signal lines for the reader. Use as many of the signal lines as required for your reader interface.

Note: Connect the data return line to the

same ground as the reader power if the reader is not powered by the VertX units 12VDC.

Pin #

1 Reader Power Shield Ground

2 Ground Hold

3 Data 0 / Data Beeper

4 Data 1 / Clock Red LED

5 Data Return Green LED

6 Green LED Data Return

7 Red LED

8 Beeper Data 0 / Data

V2000 and V100 V2000 and V100

P4 P1

Data 1 / Clock

9 Hold

10 Shield Ground Reader Power

Ground

5. RS-485 Connections – The V1000

has two - RS-485 connectors and uses

the 10-pin connector on P3 and P4.

Each RS-485 bus can support a maximum of 16 V100-Series panels using one or two ports.

Having two ports on each bus provides the option of splitting each RS-485 bus into two physical connections, allowing a total of four physical connections for the

wo busses.

t RS-485 busses must be connected in a

daisy chain topology and not a star topology.

The V1000 termination jumper should

be in the Out position if there are no

panels attached to the port. If there are downstream panels attached then the

termination jumper should be in the In

PCB Pin #

1 A 1 Not in use

2 B 2 Not in use

3 Shield 3 Shield

4 Not in use 4 B

5 Not in use 5 A

6 A 6 Not in use

7 B 7 Not in use

8 Shield 8 Shield

9 Not in use 9 B

10 Not in use 10 A

V1000 P3 (port 1 and 2)

PCB Pin #

V1000 P4 (port 3 and 4)

position.

CAUTION: The V1000 RS-485 Ports 1 & 2 (P1) are a common bus and therefore cannot hav panels with duplicate Interface Addresses assigned. The same is true of the V1000 RS-485, Ports 3 & 4 (P4). For example, two panels, both with Interface Address 0 (factory default), cannot be connected to Ports 1 and/or 2 (P1).

e

December 2010 Page 8 of 24

VertX Installation Guide

It is recommended to wire the RS-485 to the In position of the P9 terminal block of the V100-Series

panel. This is especially important when the RS-485 communication is in a “daisy chain”

configuration. If the RS-485 is wired In and Out, and power is lost, or the P9 terminal block is

unplugged on a V100-Series panel, RS-485 communications will be lost to downstream V100-Series panels.

6. Interface

the Address dial. Ensure that the V100 Interface Address

is documented in the Hardware Installation Worksheet

7. Output Connections (All VertX units) – All Output

connections are used for general purpose controls. The following table shows where the various outputs are located. Pin numbers shown use the convention “NO/C/NC”. For example, Output 1, V2000: P3 Pin1 is NO (Normally Open,) Pin 2 is C (Common,) and Pin 3 is NC (Normally Closed).

Note: Relays are dry contact rated for 2Amps @ 30VDC.

Address – Set the interface address by turning

.

Output number

1

2

3

4

December 2010 Page 9 of 24

V2000 V1000 V100 V200 V300

P3 Pins 1/2/3

Strike(lock) Relay 1

P3 Pins 4/5/6

Aux Relay 1

P6 Pins 6/5/4

Strike (lock) Relay 2

P6 Pins 3/2/1

Aux Relay 2

P14 Pins 3/4/5

P11 Pins 3/4/5

P3 Pins 1/2/3

Strike (lock) Relay 1

P3 Pins 4/5/6

Aux Relay 1

P6 Pins 6/5/4

Strike (lock) Relay 2

P6 Pins 3/2/1

Aux Relay 2

P3 Pins 2/3/4 P1 Pins 1/2/3

P6 Pins 3/2/1 P1 Pins 4/5/6

P1 Pins 7/8/9

P2 Pins 1/2/3

VertX Installation Guide

Output number

5 P2 Pins 4/5/6

6 P2 Pins 7/8/9

7 P4 Pins 9/8/7

8 P4 Pins 6/5/4

9 P4 Pins 3/2/1

10 P5 Pins 9/8/7

11 P5 Pins 6/5/4

12 P5 Pins 3/2/1

V2000 V1000 V100 V200 V300

CAUTION: Some magnetic locks exhibit both high inrush current when activated and a high instantaneous break voltage when de-energized due to magnetic field collapse. It is recommended you use of a snubber circuit across the controlling relay terminals to protect the controlling relay contacts. Go to support.hidglobal.com

, see Solution 891 - How do I wire a High

In-Rush Current locking device to VertX/Edge/Edge Solo?.

8. Input Connections (All VertX devices) – Input connections are analog inputs used for a combination of

specific functions such as Request-to-Exit (REX), Door monitor, etc. They can also be used as general

purpose monitoring. Connect one side of the switch or contact to the + (plus) lead and the other to the –

(minus) lead. The following table shows where the inputs are located. Pin numbers shown on the cover

use the convention +/–.

The default REX input configuration is normally open (NO) unsupervised (no EOL resistors).

However, the default door switch (DS) configuration is Normally Closed (NC), unsupervised (no EOL resistors).

All other input points are defaulted for NO switches and are unsupervised (no EOL resistors).

Configure any input as NO or NC, as well as unsupervised or supervised. They can be configured for supervisory resistors of 1K – 6K Ohm. The setup of supervised inputs should be done during configuration of the VertX devices via the host

Example: Input 1, V1000 is: P14 Pin1 is + and Pin 2 is -.

Except for the door monitor, all other

Supervised inputs can be configured for:

inputs default to NO, unsupervised:

December 2010 Page 10 of 24

VertX Installation Guide

Input number

1

2

3

4

5

6

7

V2000 V1000 V100 V200 V300

P2 Pins 1/2

Door Monitor

P2 Pins 3/4

REX input

P5 Pins 4/3

Door Monitor

P5 Pins 2/1

Rex Input

P7 Pins 8/7

Tamper

P7 Pins 6/5

AC Fail

P7 Pins 4/3

Batt Fail

P14 Pins 1/2

P11 Pins 4/3

P7 Pins 8/7

Tamper

P7 Pins 6/5

AC Fail

P7 Pins 4/3

Batt Fail

P2 Pins 1/2

Door Monitor

P2 Pins 3/4

REX input

P5 Pins 4/3

Door Monitor

P5 Pins 2/1

Rex Input

P7 Pins 8/7

Tamper

P7 Pins 6/5

AC Fail

P7 Pins 4/3

Batt Fail

P1 Pins 1/2 P6 Pins 2/1

P1 Pins 3/4 P3 Pins 1/2

P1 Pins 5/6

P1 Pins 7/8

P7 Pins 8/7

Tamper

P7 Pins 6/5

AC Fail

P1 Pins 9/10 P7 Pins 4/3

Batt Fail

P2 Pins 1/2

P2 Pins 3/4

8 P2 Pins 5/6

9 P4 Pins 10/9

10 P4 Pins 8/7 11 P4 Pins 6/5 12 P4 Pins 4/3

13 P4 Pins 2/1

14 P5 Pins 6/5

15 P5 Pins 4/3

16 P5 Pins 2/1

17

18

19

P7 Pins 8/7

Tamper

P7 Pins 6/5

AC Fail

P7 Pins 4/3

Batt Fail

December 2010 Page 11 of 24

VertX Installation Guide

1.6 Modem

The VertX controller will automatically answer incoming calls when an external serial modem is attached to the RS-232 port 1.

1.6.1 Modem Setup Requirements

 External Modem (not included). The modem must be selected from the following approved HID modem

list:

o Zoom V.90 56 K Fax Modem, Model 2949 (external modem uses phone jack) o U.S. Robotics V.92 56K Fax Modem, Model 5686 (external modem uses phone jack) o Telular GSM 850/1900, Model 1C02A160 (external cellular modem)

 RS-232 Serial modem cable (not included)

 HID Serial Adapter cable (included with the VertX controller)

 AC electrical outlet or surge protector for supplying power to the modem

 Analog phone line

 VertX V1000 controller

1.6.2 Physical Modem Setup

1. Connect the RS-232 Serial modem cable (purchased separately) 9 or 25-pin connector into the back of the modem.

2. Connect the other end of the RS-232 Serial modem cable (9-pin connector) into the HID Serial Adapter cable (P/N 70007). In addition, connect the HID RS-232 Serial Adapter cable into P17 RS-232 Port 1.

3. Connect one end of the phone cord (included with the modem) into the TELCO or LINE jack on the back of the modem and plug the other end into an analog telephone wall jack.

4. Plug the power adapter (included with modem) into a surge protector or electrical outlet. Make sure you use the power adapter that came with the modem, as others may be of different voltages and could damage your modem.

5. Turn on the modem. This is usually done by using a switch located next to the status lights. There may also be a power switch located on the back of the modem.

December 2010 Page 12 of 24

VertX Installation Guide

Step 2 Contact

Contact the VertX controller through two methods.

 Discovery Client (DHCP or Static TCP/IP Configurations Only)

 Virtual Port

2.1 Discovery Client

The Discovery Client provides a technician with a method of locating all of the VertX controllers that are connected to a network. Controller information is displayed providing the ability to ‘blink’ the VertX controller Comm LED and configure the unit by launching a browser pointed at the Configuration GUI of the targeted controller. When the Discovery Client is launched, a discover command is issued and the Configuration GUI screen is populated with the results. Also provided is the ability to refresh the Configuration GUI screen on command.

Use this feature when the VertX controllers and network have been installed and are operational, but before the VertX controller(s) has been configured. At this point, all of the controllers on a network will have the same host name and unknown IP addresses (assuming a DHCP environment). In this scenario, the only mechanism available to configure a controller is the serial debug port or by only placing one controller on the network at a time. The Discovery Client provides an easy to use mechanism to configure controllers.

2.1.1 Installation

An operating system of Windows® XP with .NET Framework v2.0 installed is a requirement for the Discovery Client to function properly.

1. The Discovery Client can be downloaded by placing the following path in an Internet browser.

http://www.hidcorp.com/downloads/DiscoveryClient.zip

2. The File Download dialog will display, click Open

3. When the contents of the zip file display, double-click setup.exe

4. If a security warning is received, click Run

5. From the Discovery Client Welcome page, click Next

6. Select the Installation folder and who should have access to the Discovery Client, click Next

7. Confirm the installation location, click Next

8. Click Close

December 2010 Page 13 of 24

VertX Installation Guide

2.1.2 Use

The following provides information on how to access and use the Discovery Client.

1. Enable VertX controllers on the network

2. Click Start > Programs > VertX Tool Box > Discovery GUI to access the Discovery Client

3. Returned is a list of controllers attached to the network. If there is more than one controller listed, controllers can be identified using the MAC Address label on the unit

4. If unsure of a controllers physical location click Blink ON to start the Comm LED blinking on the controller. Note the name on the button will change to Blink OFF. When verification of the controller is complete, click Blink OFF

5. Click Configure Unit to open the Basic Configuration page of that controller

6. Go to Step 3 Configure, page 15

2.2 Virtual Port

Contact a VertX controller by directly connecting the computer to the controller using an Ethernet cable. By

default, every controller is configured to respond to a fixed address: 169.254.242.121.

1. Ensure you are running a Windows 2000 or XP computer

2. Disconnect your Windows computer from its hub or network

3. Connect the Windows computer to the controller with an Ethernet cable

4 Using the Windows™ Start button, click Start > Run

5. Enter ipconfig /renew -- wait for DHCP to timeout (approximately 60 sec). The computer will acquire a 169.254.x.x address

6. Access a web browser and enter 169.254.242.121 into the Address field. The controller is now

accessible through this Virtual Port

December 2010 Page 14 of 24

VertX Installation Guide

Step 3 Configure

This section describes the communications configuration that enables the controller to communicate with the host software.

There are three methods of communication possible on a V1000 controller:

 Dynamic Host Configuration Protocol (DHCP) TCP/IP Addressing

 Static TCP/IP Addressing (see Configuration Checklist

TCP/IP configuration)

 Modem (see Configuration Checklist

Enter only the configuration that relates to your sites specific installation.

, page 21 for a list of criterion needed for a modem configuration)

, page 21 for a list of criterion needed for a Static

3.1 VertX Communications

The VertX communications configuration is provided through a browser-based application called the

Configuration GUI (Graphic User Interface).

3.1.1 Configuration GUI Login

The Login screen for that controller will display. In the User name field, enter admin (leaving the Password field empty). Click OK.

3.1.2 Basic Network Setup

Select the Connection Selection radio button to establish your systems specific communication type.

Choices include:

 Network

 Modem

 Network with Modem Backup

Default network information will load. Before making changes, review the default network information.

Note: Most configurations will not require accessing the Advanced Setup screen.

3.1.2.1 Static Network

If using a Static TCP/IP network, proceed with changes using the information collected on the Configuration

Checklist, page 21.

3.1.2.2 DHCP Network

If using a DHCP TCP/IP network, this information is configured automatically.

3.1.2.3 Modem

If using a Modem, proceed with changes using the information collected on the Configuration Checklist

21.

December 2010 Page 15 of 24

, page

VertX Installation Guide

3.1.3 Host Communication Setup

Enter the Host Name, and the Here I Am Interval collected on the Configuration Checklist, page 21.

3.1.3.1 Controller Login Password

During your first instance of accessing the Configuration GUI, you must change the password (located at the bottom of the screen). Enter a new password, and reenter the password in the second field.

Note: This step is not necessary during any consecutive Configuration GUI sessions. However on consecutive

sessions the password may be changed.

Once configuration changes have been made, click Submit, and the Confirmation page (see 3.1.4

Confirmation, page 16) will display.

3.1.4 Confirmation

Once configuration changes are complete and submitted, the Confirmation screen will display. Verify that the changes submitted are accurate, and click Save. If the changes submitted are not accurate, click Cancel and

adjust the settings appropriately.

Step 4 Communicate

Now that the controller is connected, contacted and configured, contact the host to test the system.

Basic setup is now complete!

Additional trouble-shooting tools are available on the System Status and Supplemental Configuration (page 17) screens.

December 2010 Page 16 of 24

VertX Installation Guide

Appendices

Trouble-shooting

System Status

System Status provides a technician with a method of validating the VertX installation, field wiring and installed devices. Perform the System Status at any time after the VertX controller has been installed and power is available. In addition, a technician may perform a system status as many times as necessary.

Upon startup, the System Status page will discover all connected and powered V100-Series devices attached

to the controller and displays the inputs, outputs, and host status.

Reference the Legend to determine the meaning of the different images. By clicking Add Unconfigured you can configure the V1000 for the attached panels and readers. The

assumption is that two readers are attached to any V100 interface panel and that both readers are Wiegand card only. Once the configuration is complete, the VertX software will refresh.

Once the page refreshes, a Restore Previous button becomes available. The Restore Previous button enables the technician to use the previously saved configuration.

Supplemental Configuration

Supplemental Configuration provides the ability to view and configure system inputs and outputs These buttons provide navigation to the following functionality:

Configure - configure inputs, outputs and door characteristics for a V1000, V100, V200, and V300

System Time - update System Time

Update System – updates the interface boards firmware

Configure

Configure provides the ability to view and modify system inputs and outputs and door characteristics.

Upon successful validation, the Save button will write modified values to the interface board.

System Time

System Time provides the ability to view and set the date, time, and time zone values on the controller. Upon initialization, Date, Time, Time Zone and TZ fields will be populated with the current system settings. The

date displayed (non-text box) will be updated approximately every 30 seconds.

The Time Zone field provides a drop-down menu. One of the options in the Time Zone drop-down menu is Custom Time Zone. If Custom Time Zone is selected, the TZ text box will be enabled. Otherwise, the TZ is associated with the Time Zone field.

Update System

Update System allows the user to update the firmware on the interface board. During a download the interface board image flashes between grey and yellow. When a download completes the image color changes to green for successful or red for failure. If the download fails, a tool tip with the error status code may be viewed by hovering the mouse over the image in question.

Initially, all of the interface boards will be selected for a download to commence.

Note: Depending on the VertX controller and system, it may take several minutes to completely download.

December 2010 Page 17 of 24

VertX Installation Guide

Network Defaults Jumper

The Netw

ork Defaults Jumper requires that someone with physical access to the V1000, place a jumper over

the debug port prior to the controller rebooting. The controller reconfigures its network settings to the factory defaults when the jumper is on the debug port during a reboot. From this point, configuration (or reconfiguration) will proceed normally.

Use the Network Defaults Jumper to correct potential errors in a VertX controllers network configuration.

1. Place a jumper over the right two pins of the P9 debug port.

2. Reboot the controller to change all of the network configuration settings back to the factory defaults.

3. After the LED turns amber, remove the jumper from the P9 debug port. Upon removing the jumper it takes approximately 60 seconds for the controller to reset. Once the reset is complete, the LED will return to green.

CAUTION: During the process of rebooting the controller, all network configuration information will be overwritten and returned to the original defaults.

4. Configure the controller for your installation parameters. See 3.1 VertX Communications, page 15.

Firewall

If the VertX controller is being installed where it communicates through a firewall, then the firewall may need to be configured to allow TCP data transfer on the specified port(s).

1. Before starting, ensure that any pop-up blocker software is disabled on the computer.

2. Open the following ports on the firewall.

connection_port(4070)TCP outbound.This port must be open on the Host computer.



listen_port(4050)TCP incoming. This port must be open when using selected



applications.

If you are not familiar with configuring a firewall for a network, contact the Network/IT administrator or

manager.

CAUTION: If the firewall is not configured properly the controller may not communicate with the host.

December 2010 Page 18 of 24

VertX Installation Guide

Contact Information

Americas

HID Global (California, USA) support: support_na@hidvertx.com sales: sales@hidvertx.com main: (949) 598-1600 sales: (800) 210-4744 telephone: 1-800-237-7769 fax number: (949) 598-1690

Europe, Middle East and Africa

HID Corporation, Ltd. (Haverhill, UK) support: support_emea@hidvertx.com sales: salesemea@hidvertx.com telephone: +44 1440 714 850 fax number: +44 1440 714 840

Asia-Pacific

HID Asia Pacific Ltd. (Hong Kong) support: support_APAC@hidvertx.com sales: salesapac@hidvertx.com telephone: (852) 3160 9802 fax number: (852) 3160 4809

December 2010 Page 19 of 24

VertX Installation Guide

Regulatory

All National and local Electrical codes apply.

 This equipment is intended to be powered from a limited power source output of a

previously certified power supply.

 Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Class A Digital Devices FCC Compliance Statement: This equipment has been tested and found to comply with the limits for a

Class. A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Canada Class A

CE Mark – Europe (EU)

C-Tick – Australia and New Zealand

VCCI – Japan

UL Recognized Component (UL294 and UL1076)

December 2010 Page 20 of 24

VertX Installation Guide

Configuration Checklist - Static and Modem

Ensure that the Configuration checklist contents are provided prior to installing a VertX controller with Static TCP/IP or

Modem configuration. Note: Advanced setting requirements are shown in gray.

Contact

Name Email Phone Number

IT contact

Sales / PM

Hardware

Name Source Part Number

Ethernet Cable

Computer with Web Browser

Hub (Optional)

Modem (Optional)

VertX Modem Cable (Optional) HID 70007

AC Electrical Outlet or Surge Protector (Optional)

Configuration Data

Connection Type Network (DHCP/Static), Modem, Network with Modem

VertX IP Address . . .

Subnet Mask . . .

Default Gateway . . .

Primary DNS Server . . .

Secondary DNS Server . . .

Network Broadcast . . .

Domain Name

VertX Host Name

FTP Enabled Yes No

Telnet Enabled Yes No

Virtual Port Enabled Yes No

Host Addressing (IP Address or Host Name) . . . OR

Here I Am Interval (sec)

TCP/IP Connection Port

TCP/IP Listen Port

Login Password

Modem

Modem Type

Incoming Mode

Host Phone Number - -

VertX RS-232 Port 1 or 2

Modem Host (IP Address or Host Name) . . . OR

December 2010 Page 21 of 24

VertX Installation Guide

Intentional Blank

December 2010 Page 22 of 24

VertX Installation Worksheet

This installation worksheet is provided for you to have a historical record of your system settings. Complete each appropriate field, and keep this worksheet in a safe location.

Record if the input is wired: 1) N/O or N/C, 2) Unsupervised or Supervised (resistor values), and 3) what

type of device is attached.

Record if output is wired: 1) N/O or N/C and 2) what type of device is attached.

V1000/V2000 Information:

Customer Name: Contact:

Installed Location: MAC Address:

Modem Model: RS232 Port #: Phone #:

Hostname: IP Address:

Tamper: AC Fail: BATT Fail:

Input 1: Input 2: Relay 1: Relay 2:

V100-Series Information (If V2000, there is a V100 at Interface Address 0 built-in):

Reader

V100 Door /

V200 Input

Interface

Monitor

Interface

Interface Address: (0-31)

Tamper: AC Fail: BATT Fail:

Reader 1: Reader 2:

Door Switch 1: REX 1: Door Switch 2: REX 2

Strike Relay 1: Aux Relay 1: Strike Relay 2: Aux Relay 2:

Input 1: Input 2: Input 3: Input 4:

Input 5: Input 6: Input 7: Input 8:

Input 9: Input 10: Input 11: Input 12:

Input 13: Input 14: Input 15: Input 16:

Relay 1: Relay 2:

Relay 1:

Relay 5: Relay 6: Relay 7: Relay 8:

Relay 2: Relay 3: Relay 4:

Interface Type:

(V100, V200, V300, V2000)

Control

V300 Output

December 2010 Page A1

Relay 9: Relay 10: Relay 11: Relay 12:

Interface

Input 1: Input 2:

VertX Installation Worksheet

V100-Series Information (If V2000, there is a V100 at Interface Address 0 built-in):

Reader

V100 Door /

V200 Input

Interface

Monitor

Interface

Interface Address: (0-31)

Tamper: AC Fail: BATT Fail:

Reader 1: Reader 2:

Door Switch 1: REX 1: Door Switch 2: REX 2

Strike Relay 1: Aux Relay 1: Strike Relay 2: Aux Relay 2:

Input 1: Input 2: Input 3: Input 4:

Input 5: Input 6: Input 7: Input 8:

Input 9: Input 10: Input 11: Input 12:

Input 13: Input 14: Input 15: Input 16:

Relay 1: Relay 2:

Relay 1:

Relay 5: Relay 6: Relay 7: Relay 8:

Relay 2: Relay 3: Relay 4:

Interface Type:

(V100, V200, V300, V2000)

Control

V300 Output

December 2010 Page A2

Relay 9: Relay 10: Relay 11: Relay 12:

Interface

Input 1: Input 2:

HID V100, V200, V300, V1000, V2000 Installation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Contents

Introduction

Parts List

Product Specifications

Cable Specifications

Overview

Step 1 Connect

1.1 What you need before getting started

1.2 V1000 or V2000

1.3 Mounting Instructions

1.4 V100, V200, or V300

1.5 Wiring VertX

1.6 Modem

1.6.1 Modem Setup Requirements

1.6.2 Physical Modem Setup

Step 2 Contact

2.1 Discovery Client

2.1.1 Installation

2.1.2 Use

2.2 Virtual Port

Step 3 Configure

3.1 VertX Communications

3.1.1 Configuration GUI Login

3.1.2 Basic Network Setup

3.1.3 Host Communication Setup

3.1.4 Confirmation

Step 4 Communicate

Appendices

Trouble-shooting

System Status

Supplemental Configuration

Network Defaults Jumper

Firewall

Contact Information

Regulatory

Configuration Checklist - Static and Modem

VertX Installation Worksheet