HID ProxCard Handling User Manual

Access Control Card

Handling Guide

Please Read Carefully

MART

S

S

S

HID CORPORATION

C

NTACTLE

O

RD

A

C

An ASSA ABLOY Group company

DO'S AND DON'TS FOR ALL HID CARDS

General Information:

HID Cards are made of PVC, except for the ProxCard II,

R

which consists of a polycarbonate base with a PVC cover.
Proximity cards contain an antenna coil and integrated
electronic chip. Wiegand cards contain magnetic wire
strips. Glossy finish PVC cards or direct print overlays
are suitable for dye-sublimation printing of images,
photos and text.

Care should be taken to follow HID's handling and
printing recommendations.

Do Not Do The Following:

Do not use for any other purpose other than for
access control or identification.
Do not leave in direct sunlight, for example on the
dash of a car.
Do not expose to extreme heat or open flame. For
example, clothes dryers or clothes irons.
Do not expose to organic solvents, thinners, mineral
spirits, etc.
Do not machine wash.
Do not use as an ice scraper or scraping tool.
Do not crimp, bend, or twist card.
Do not re-laminate.
Do not immerse in alcohol, Isopropyl, ethanol,
methyl, etc.
Do not bite.
Do not pound with a pen or tool.
Do not punch a slot or hole in an undesignated area.

Okay To Do The Following:

Place in a wallet or purse.
Direct image with dye sublimation printers.
Clean with a soft, non-scratching cloth and water.

Page 2

PRINTING INSTRUCTIONS

HID's ISO and Duo Prox cards are shipped to you shrink

1.

wrapped. Care should be taken not to scratch cards when
opening shrink wrapping, especially when using a knife or
other sharp object.

Even with careful card handling, it is possible that the image

2.

quality may vary. This can be due to printer setup variations,
lot to lot material variations, environmental changes, printer
types, background color selections and other variables. HID
Corporation is not responsible for image quality variations.
These cards have been quality controlled to a specification
that meets requirements for high quality images. Failure to
achieve the desired image quality is not a fault of the card.

Gloves that are free of any powder residue should be worn

3.

when handling cards. Oils from your hands will transfer to
the cards and may cause smudging, fingerprints or other
distortions to appear on the cards.

Cards should be handled by the edges, not the flat,

4.

finished surface.
Always check cards for noticeable debris. In some instances

5.

there may be minute pieces of vinyl on the card. Carefully
clean all cards with 99% pure Isopropyl alcohol. You can
find this at your local pharmacy. Anything other than

99% pure alcohol may leave residues on the card surface.

The office where you plan to print cards should be neat,

6.

clean and free of airborne particles. Any dirt or debris that
is on the cards, or that gets into the printers, may render the
card unprintable and/or damage the printer.

Check the printer's roller often. The manufacturer's instructions

7.

generally call out for the roller to be cleaned after 250 cards
have been run or, with every ribbon change. We recommend
a maximum of 50 cards being run before the roller is cleaned.
Check your printer manual or contact the printer manufacturer
for specific details.

If a card has been dropped or mishandled, do not attempt to

8.

print on it until it has been thoroughly cleaned with 99% pure
Isopropyl alcohol only.

Occasionally, very fine scuff marks may be seen on the surface

9.

of cards. These marks will not affect the printer, nor will they
affect the outcome of the printed images. These scuff marks
sometimes occur during final inspection and testing for
functionality of the card.

Surface imperfections caused by embedded components may

10.

cause color variations or printing voids. When designing card
artwork, avoid large areas with solid or screened color
backgrounds or half-tones, do not place a logo or a photo portrait
over the chip location or opposite the edge of a magnetic stripe,
and use art with varied color or pattern. A white background gives
a professional appearance, and is most likely to yield successful
results. Always print a few test cards, and be prepared to make
minor adjustments the artwork to create the best appearance.

(Continued on Page 4) Page 3

PRINTING INSTRUCTIONS (Cont'd.)

The drawing below outlines the recommended print area on
the card. Some printers are capable of full-bleed or
edge-to-edge printing. HID recommends that you run some
test cards on your printer before designing your graphics for
edge-to-edge printing. Also, most printer manufacturers
discourage printing on cards which are pre slot punched,
as the slot edge may tear the printer ribbon or interfere with
the end-of-card sensor and stop the printing process.
Print your cards first, then slot punch them. If your cards are
already punched, do not print in the area near the slot (dark
hatched area in diagram below).

.125"

.317 cm

.125"

.317 cm

Do NOT print this area if card is slotted on this edge.

PRINT AREA

(unless card is slot punched)

.450"

1.143 cm

Do NOT print this area if card is slotted on this edge.

.125"

.317 cm

We hope these suggestions will help you
successfully print on your HID cards.

HID Corporation, Irvine

9292 Jeronimo Road
Irvine, CA 92618-1905
Tel: [phone]

Fax: [phone]

www.HIDCorp.com

HID Corporation, CT

333 State Street

North Haven, CT 06473

Tel: [phone]
Fax: [phone]

www.HIDCorp.com

.450"

1.143 cm

Page 4