HID FlexSmart 607, FlexSmart 6075, FlexSmart 6076, FlexSmart 6077, FlexSmart 6073 Installation Manual
...Page 1
9292 Jeronimo Road
Irvine, CA 92618-1905
HID® FlexSmart™
607X Series Readers
INSTALLATION GUIDE
© 2007 HID Global Corporation. All rights reserved.
February 5, 2006
Document Number 6075-900
Document Version B.2
Page 2
6075-900, B.2 – FlexSmart™ 607X Series Installation Guide
Contents
1 Overview ............................................................................................................................................... 3
2 Mounting ...............................................................................................................................................4
3 Wiring ................................................................................................................................................... 5
Regulatory ................................................................................................................................................... 7
Models ................................................................................................................................................... 7
Contact ................................................................................................................................................... 8
List of Figures
Figure 1 Reader Dimensions and Mounting........................................................................................................ 4
Figure 2 Keypad Reader Dimensions and Mounting.......................................................................................... 5
Page 2 of 8 February 5, 2007
© 2007 HID Global Corporation. All rights reserved.
Page 3
FlexSmart™ 607X Series Installation Guide – 6075-900, B.2
1 Overview
1.1 Introduction
The HID® FlexSmart™ readers can easily be configured at the site because the readers’ bezel can be
interchangeably snapped onto the common reader module (only standard reader).
The FlexSmart readers mount on any North American standard electrical gang box or on any flat surface,
with snap-on bezels.
1.2 Parts Included
First, unpack the contents and become familiar with the components.
The following items will be included with FlexSmart readers:
1. Installation Guide
2. MIFARE reader module for Slim or Wall switch
3. Cover Bezel (reader only)
1.3 Specifications
Supply Voltage
Supply Current
Input
Output formats
Operating Frequency
Data Transmission
Operating Temperature
Non-Operating Temperature
Operating Humidity
Finish
Dimensions
9VDC to 16VDC
15 / 75mA Keypad 25 / 100mA
1-line LED (red/green), 1-line buzzer
Wiegand/ABA, Application dependant
13.56MHz, 106kBaud
Contactless
-25oC to +55oC
o
-40
C to +70oC
5% to 95% condensing
Black (Standard)
4.30” x 1.5” x .72” (10.9 x 3.8 x 1.8 cm)
Weight
February 5, 2007 Page 3 of 8
4.70” x 2.9” x 1.1” (11.9 x 7.4 x 2.8 cm)
4 oz (113g) keypad 12 oz (340g)
© 2007 HID Global Corporation. All rights reserved.
Page 4
6075-900, B.2 – FlexSmart™ 607X Series Installation Guide
1.4 Identifying the Reader Format
The reader format is found on the ID label (see below), which is located on the reader electronics module.
Reader
Format
2 Mounting
Page 4 of 8 February 5, 2007
Figure 1 Reader Dimensions and Mounting
© 2007 HID Global Corporation. All rights reserved.
Page 5
FlexSmart™ 607X Series Installation Guide – 6075-900, B.2
Figure 2 Keypad Reader Dimensions and Mounting
2.1 Mullion Mounting
The following describes how the readers mount to a mullion.
1. Drill two holes 6-32 or M-3 sheet metal or thread forming screws 3.3” (8.38 cm) apart.
2. Locate and drill a 0.375” (0.95 cm) hole for the reader cable.
3. Route the cable through the center hole to the controller.
4. Using the two 6-32 or M-3 screws, attach the reader to the first two mounting holes.
5. Once the reader module is screwed in place, snap on the bezel.
3 Wiring
3.1 Cable Types and Maximum Lengths
The MIFARE readers require a minimum voltage of 9.0 VDC. Voltage drops, caused by the cable
resistance, can be made by increasing the power supply voltage.
CAUTION: DO NOT SET THE POWER SUPPLY VOLTAGE TO HIGHER THAN 16 VDC.
CAUTION: DO NOT USE CABLES WITH GAUGES SMALLER THAN 24 AWG:
February 5, 2007 Page 5 of 8
© 2007 HID Global Corporation. All rights reserved.
Page 6
6075-900, B.2 – FlexSmart™ 607X Series Installation Guide
The following are recommended cable types and maximum cable lengths for a cable connecting the power supply
to the reader.
Cable Type Maximum Cable Length
24 AWG (0.60mm), three conductors, with an overall foil shield, 9533 or
equivalent.
200’ (61 m)
22 AWG (0.80mm), two conductors, with an overall foil shield, Alpha 5192
or equivalent.
18 AWG (1.20mm), two conductors, with an overall foil shield, 5836 or
equivalent.
The following are recommended wiring types at various maximum distances. Variations in distances
require different wire gauges, because of system data termination differences. Contact your system
manufacturer for its exact requirements. Installation should be in accordance with National Electric Code
ANSI/NFPA 70.
22 AWG (0.80mm), six or eight conductor, with an overall foil shield, Alpha
5196, 5198 or equivalent.
18 AWG (1.20mm), six or eight conductor, with an overall foil shield, Alpha
5386, 5388 or equivalent.
3.2 Grounding
Connect the reader directly to an earth ground (an earth ground can be established by driving a copper
clad ground rod into the earth). Make certain the DC resistance between your established earth ground
and the system ground is 50 Ohms or less. If a direct connection to a ground rod is not possible, connect
the reader to an earth grounded cold water metal pipe (do not connect to a copper fire sprinkler system
because it may have non-conductive couplings) or steel frames (building beams) that connect to earth.
Connection of the shield/drain to an earth ground will provide greater ESD protection of the reader.
Prevent ground loops by connecting both the cable shield and the negative line of the power supply to one
common earth ground point. Connecting different points to separate earth grounds may result in a ground
loop.
300’ (91 m)
500’ (152 m)
Cable Type Maximum Cable Length
500’(152 m)
500’ (152m)
Note: For the heavy duty keypad readers, the Shield/drain wire should be floating at the power supply.
Note: Ground loops may cause poor read range and communication line interference, resulting in no code
or improper code seen by the controller.
Reader Defaults
Card read (LED, beep & backlight) Red +12Vdc
One-line control (bi-colour LED) Black 0Vdc
Keypad Defaults Green Data 0/Strobe
Key-press (LED, beep & backlight) White Data 1/Data
1 0001 2 0010 3 0011 Brown LED Control
4 0100 5 0101 6 0110 Blue Beeper Control
7 0111 8 1000 9 1001 Orange Not Used
Θ1010
0 0000 # 1011 Shield/drain Door controller earth ground
Reader Wiring
Page 6 of 8 February 5, 2007
© 2007 HID Global Corporation. All rights reserved.
Page 7
FlexSmart™ 607X Series Installation Guide – 6075-900, B.2
Notes:
• Keypad outputs only available
• The system must have a single earth ground point.
• As shown, do not connect shield (screen) wire at reader cable splice.
• For open collector (non-terminated output), consult your system manufacturer for correct cable length
and type.
Regulatory
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
UL
This reader is intended to be used with UL294 Listed Control Equipment.
CE
Hereby, HID declares that this proximity reader is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Models
Readers
6075 HID Format MIFARE Reader
6076 Custom MIFARE Reader
6077 Custom DESFire Reader
Keypad Readers
6071 HID Format MIFARE Reader
6072 Custom MIFARE Reader
6073 Custom DESFire Reader
February 5, 2007 Page 7 of 8
© 2007 HID Global Corporation. All rights reserved.
Page 8
6075-900, B.2 – FlexSmart™ 607X Series Installation Guide
Contact
Americas
HID Corporation (California, USA)
Email:
tech@hidcorp.com
main: (949) 598-1600
support: 1-800-237-7769
fax: (949) 598-1690
Europe, Middle East and Africa
HID Corporation, Ltd. (Haverhill, UK)
email:
eusupport@hidcorp.com
main: +44 (0) 1440 714 850
support: +44 (0) 1440 711 822
fax number: +44 (0) 1440 714 840
Asia-Pacific
HID Asia Pacific Ltd. (Hong Kong)
email:
asiasupport@hidcorp.com
main: (852) 3160 9800
support: (852) 3160 9802
fax : (852) 3160 4809
Page 8 of 8 February 5, 2007
© 2007 HID Global Corporation. All rights reserved.
Loading...