HID EDM-M Installation Guide

EDGE EVO

15370 Barranca Parkway
Irvine, CA 92618-2215
USA

© 2009 - 2012 HID Global Corporation. All rights reserved.

The EDGE EVO Door module is wired to interface with the EDGE EVO device (Hi-O Networked Controler & Reader or Networked
Controller) with electronic door components. Designed for providing interface to traditional discrete access inputs and outputs, the Door

Module provides four input analog/digital inputs and two outputs. Congure the Door Module in two ways; as a primary door interface to
REX, Door Position Switch, Battery Fail, Power Fail, Lock, and Aux (Group 1) or as a general purpose input/output module (Group 2).

Specifications

CONDITIONS

DC Input (NSC)

DC Input (MAX)

Input

Supervised inputs

(AC, Batt, REX, Door Mon) (MAX)

Strike *** /

AUX

NC or NO

DC Output

Output

(MAX)

AUX 12 VDC

Input @

Controller

AUX 24VDC

Input @

Controller

PoE Input @

Controller

AUX 12-24 VDC

/ PoE Input @

Controller

NSC = Normal Standby Condition ** Each Relay
* Combined output rating not to exceed V*I = W *** Shared between relays

1.2 Amp (+24 VDC AUX Input, 28.8 W)

1.2 Amp (+12 VDC AUX Input, 12.96 W)

Unregulated (Wet)

Jumpers

Unregulated (Wet)

Jumpers

Regulated (Wet)

Jumpers – 12 VDC
Unregulated (Wet)

Jumpers

Regulated (Wet)

Jumpers – 12 VDC

Jumpers Set to Dry

VOLTAGE DC
(VDC)

+12 VDC 0.04 Amp 0.48
+24 VDC 0.04 Amp 0.96
+12 VDC 0.80 Amp 9.6
+24 VDC 0.80 Amp 19.2
0-5 VDC

Reference

+10 to +12 VDC 0.70 Amp* 8.40

+23 to +24 VDC 0.70 Amp* 16.80

+10 to +12 VDC 0.70 Amp* 8.40

+16.5 to 24 VDC 0.30 Amp* 7.2

+10 to +12 VDC 0.50 Amp* 6.0

+12 to 24 VDC

External

CURRENT
(Amp)

0.005 Amp

(Sink)

2.00 Amp** 24.00

POWER
(W)

0.025

OPERATING
TEMPERTURE

32° - 122°F

(0° - 50° C)

CABLE LENGTH

Inputs = 500 ft (150 m)

Outputs = 500 ft (150 m)

Hi-O CAN Bus Total Length 100 ft (30 m) -

22 AWG ● 0.65mm ● 0.33mm

Maximum between drops 30 ft (10 m)

22 AWG ● 0.65mm ● 0.33mm2

Door Module

EDM-M

InstallatIon GuIde

82342-901, Rev C.1

December 2012

UL REF
NUMBER

MEDMAxNN

2

x = K for Black

G for Grey

®

Door Module

Hi-O Group Select Jumper

EDM-M

Wiring

Short = Group 1, Open = Group 2

( )

Outside Door Inside Door

Optional
Supervised Inputs

1-6K

1-6K

1-6K

N/O

N/C

Relay Jumpers

P9

P5

P8

P6

P4

P7

10 P3 14 P1 1

-+

-+-+-+

REX

BATT AC

SENSE

Door

Mon

6 P10 1

NO

*

COM

AUX

NC

NO

DS

NC

COM

* Internal Optical Tamper Disable Jumper

82342-901 C.1

CAN V+
GND
CAN H
CAN L

HI-O CANbus

1-6K
N/O

CAUTION: Some magnetic locks exhibit both high inrush current when activated and a high instantaneous break

voltage when de-energized due to magnetic eld collapse. It is recommended you use of a snubber circuit
across the controlling relay terminals to protect the controlling relay contacts. Go to support.hidglobal.
com, see Solution 891 - How do I wire a High In-Rush Current locking device to VertX/EDGE EVO.
Not evaluated by UL.

Note: Connect the Door Monitor to avoid a Door Forced Alarm.

Internal Optical Tamper

To disable the internal optical tamper sensor, attach a jumper wire from P3 pin 1 to P3 pin 2.

Note: If desiring an external tamper, wire an unsupervised Normally Closed contact to the Optical Tamper pins.

Relay Jumpers

AUX Wet

CAN V+

3 1

3 13 1 3 1

AUX Wet

+12VDC

AUX Dry

P9

P5

DS Wet

CAN V+

DS Wet

+12VDC

3 13 1

DS Dry

P6

P4

INSTALLATION GUIDE

2

JUMPER =

P8

P7

©2009 - 2012 HID Global Corporation. All rights reserved.

82342-901 C.1

Door Interface Board Groups 1 and 2

Group 1

Following are the inputs when the unit is congured for Group 1.

Input Port Pin

AC - P3 Pin3

AC + P3 Pin 4

BATT - P3 Pin 5

BATT + P3 Pin 6

REX - P3 Pin 7

REX + P3 Pin 8

Door Mon - P3 Pin 9

Door Mon + P3 Pin 10

Group 2

Following are the inputs when the unit is congured for Group 2.

Input Port Pin

Input 4 - P3 Pin3

Input 4 + P3 Pin 4

Input 3 - P3 Pin 5

Input 3 + P3 Pin 6

Input 2 - P3 Pin 7

Input 2 + P3 Pin 8

Input 1 - P3 Pin 9

Input 1 + P3 Pin 10

Door Module

EDM-M

©2009 - 2012 HID Global Corporation. All rights reserved.

INSTALLATION GUIDE

3

Regulatory

UL

Connect only to a Listed Access Control / Burglary power-limited power supply, or Listed Access Control / Burglary PoE (Power-over-Ethernet) adapter.

All National and local Electrical codes apply. Install in accordance with NFPA70 (NEC), Local Codes, and authorities having jurisdiction.

Indoor use only.

EDGE EVO Modules are UL Listed for installation within a protected area.

Mount onto UL Listed Single-Gang electrical box.

All panic and alarm hardware and equipment shall be UL Listed.

All cabling and wire shall be UL Listed or Recognized and suitable for the application.

All splices and connections shall be mechanically secure and bonded electrically.

For operation, testing and maintenance, refer to the Hi-O Network Controller & Reader (82000-922) and Hi-O Networked Controller Installation Guides (82000-920).

CAUTION: Any changes or modifcations to this devise not explicitly approved by the manufacturer could void your authority to operate this equipment.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.

Canada Radio Certification

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes
: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

CE MARKING

HID Global hereby declares that these proximity readers are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

The controller portion is in compliance with the essential requirements and other relevant provision of Directive 2004/108/EC.

JAPAN MIC

この装置は認証済みです。

TAIWAN NCC

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得
影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功
率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

According to «Administrative Regulations on Low Power Radio Waves Radiated Devices» without permission granted by the NCC, any company, enterprise, or user is not allowed
to change frequency, enhance transmitting power or alter original characteristic as well as performance to an approved low power radio-frequency devices. The low power radio­frequency devices shall not inuence aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is achieved.
The said legal communications means radio communications is operated in compliance with the Telecommunications Act.

The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices.

ACCESS experience.

© 2009 - 2012 HID Global Corporation. All rights reserved.

Check reader label for current regulatory approvals.

hidglobal.com

82342-901 Rev C.1

Patent Pending

HID Global

North America

15370 Barranca Parkway
Irvine, CA 92618
USA
Phone: [phone]
Fax: [phone]

Asia Pacific

19/F 625 King’s Road
NorthPoint, Island East
Hong Kong
Phone: [phone]
Fax: [phone]

support.hidglobal.com

HID GLOBAL, HID, the HID logo, EDGE EVO and Hi-O are the trademarks or registered
trademarks of HID Global Corporation, or its licensors, in the U.S. and other countries.

Europe, Middle East & Africa

Phoenix Road
Haverhill, Suolk CB9 7AE
England
Phone: [phone]
Fax: [phone]