Hewlett-Packard 2133 User Manual

HP 2133 Mini-Note PC
Maintenance and Service Guide
© Copyright 2008 Hewlett-Packard Development Company, L.P.
Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Microsoft, Windows, and Windows Vista are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
First Edition: April 2008
Document Part Number: 465236-001
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of Information Technology Equipment (IEC 60950).
iii
iv Safety warning notice
Table of contents
1 Product description
2 External component identification
Top components ...................................................................................................................... 4
Display .................................................................................................................... 4
Keys ........................................................................................................................ 5
TouchPad ................................................................................................................. 6
Front components ..................................................................................................................... 7
Right-side components .............................................................................................................. 8
Left-side components ................................................................................................................. 9
Bottom components ................................................................................................................ 10
3 Illustrated parts catalog
Serial number location ............................................................................................................ 11
Computer major components ................................................................................................... 12
Bracket Kit ............................................................................................................................. 16
Plastics/Cable Kit .................................................................................................................. 17
Miscellaneous parts ................................................................................................................ 17
Sequential part number listing .................................................................................................. 18
4 Removal and replacement procedures
Preliminary replacement requirements ....................................................................................... 21
Tools required ......................................................................................................... 21
Service considerations ............................................................................................. 21
Plastic parts ............................................................................................. 21
Cables and connectors ............................................................................. 22
Drive handling ......................................................................................... 22
Grounding guidelines .............................................................................................. 23
Electrostatic discharge damage .................................................................. 23
Packaging and transporting guidelines ........................................ 24
Workstation guidelines .............................................................. 24
Equipment guidelines ................................................................. 25
Unknown user password .......................................................................................... 26
v
Component replacement procedures ........................................................................................ 27
5 Computer Setup
Starting Computer Setup ......................................................................................................... 53
Using Computer Setup ............................................................................................................ 54
Computer Setup menus ........................................................................................................... 55
Serial number ......................................................................................................... 27
Computer feet ......................................................................................................... 28
Battery ................................................................................................................... 29
Keyboard ............................................................................................................... 30
Memory module ...................................................................................................... 32
Mass storage device ................................................................................................ 33
Top cover ............................................................................................................... 35
Audio board ........................................................................................................... 37
Bluetooth module .................................................................................................... 39
System board ......................................................................................................... 41
WLAN module ........................................................................................................ 45
RTC battery ............................................................................................................ 47
Fan/heat sink ......................................................................................................... 49
Display assembly .................................................................................................... 51
Navigating and selecting in Computer Setup .............................................................. 54
Restoring factory settings in Computer Setup ............................................................... 54
File menu ............................................................................................................... 55
Security menu ......................................................................................................... 55
System Configuration menu ...................................................................................... 56
6 Specifications
Computer specifications .......................................................................................................... 57
8.9-inch, WXGA display specifications ..................................................................................... 58
Hard drive specifications ........................................................................................................ 59
System DMA specifications ...................................................................................................... 60
System interrupt specifications ................................................................................................. 61
System I/O address specifications ............................................................................................ 62
System memory map specifications .......................................................................................... 64
7 Screw listing
Phillips PM2.0×3.0 screw ....................................................................................................... 65
Torx8 T8M2.0×6.0 screw ....................................................................................................... 66
Torx8 T8M2.5×5.0 screw ....................................................................................................... 69
Torx8 T8M2.5×10.0 screw ..................................................................................................... 71
Torx8 T8M2.0×4.0 screw ....................................................................................................... 72
8 Backup and recovery—Windows Vista
vi
Overview .............................................................................................................................. 73
Creating recovery discs .......................................................................................................... 73
Backing up your information .................................................................................................... 74
Backup tips ............................................................................................................ 74
Backing up individual files or folders ......................................................................... 75
Backing up the entire hard drive ............................................................................... 75
Scheduling an automatic backup .............................................................................. 75
Creating system restore points .................................................................................. 76
Performing a recovery ............................................................................................................ 76
Recovering individual files ........................................................................................ 77
Restoring the computer to a previous state .................................................................. 77
Recovering information using f8 recovery tools ........................................................... 78
Recovering information using Windows Recovery Environment (WinRE) .......... 78
Recovering information using Recovery Manager ......................................... 79
Recovering information using a Windows Vista operating system DVD (purchased
separately) ............................................................................................................. 79
9 Backup and recovery—Windows XP
Backing up your information .................................................................................................... 81
When to backup ..................................................................................................... 81
Backup suggestions ................................................................................................. 81
Backing up individual files or folders ......................................................................... 82
Backing up all files and folders ................................................................................. 82
Creating recovery points .......................................................................................... 83
Scheduling backups ................................................................................................ 83
Performing a recovery ............................................................................................................ 84
Initiating a recovery in Windows .............................................................................. 84
10 Connector pin assignments
Audio-out (headphone) ........................................................................................................... 85
Audio-in (microphone) ............................................................................................................ 85
External monitor ..................................................................................................................... 86
RJ-45 (network) ...................................................................................................................... 87
Universal Serial Bus ................................................................................................................ 87
11 Power cord set requirements
Requirements for all countries and regions ................................................................................. 88
Requirements for specific countries and regions ......................................................................... 89
12 Recycling
Battery .................................................................................................................................. 90
Display ................................................................................................................................. 90
vii
Index ................................................................................................................................. 96
viii
1

Product description

Category Description
Product Name
Processors
Chipset
Southbridge: VIA 8237s
Graphics
Panels
Memory
Supports up to 2 GB of system RAM
PC2-5300, 667-MHz, DDR2
Supports the following configurations:
HP 2133 Mini-Note PC
VIA Technology C7-M Ultra-Low Voltage (ULV) processors
VIA C7-M ULV 1.6-GHz processor, 800-MHz front-side bus (FSB), 8-W thermal design power (TDP)
VIA C7-M ULV 1.2-GHz processor, 800-MHz FSB, 5-W TDP
VIA C7-M ULV 1.0-GHz processor, 400-MHz FSB, 3.5-W TDP
Northbridge: VIA CN896
VIA Universal Memory Architecture (UMA) graphics subsystem
All display assemblies include 2 microphones, 2 speakers, and 2 WLAN antenna transceivers and cables
8.9-inch WXGA (1280 × 768) with camera
8.9-inch WXGA (1280 × 768) without camera
One customer-accessible/upgradable memory module slot
2048-MB total system memory (2048 × 1)
1024-MB total system memory (1024 × 1)
512-MB total system memory (512 × 1)
Mass storage device
Supports the following SATA hard drives:
Supports 9.5-mm (2.5-inch) SATA 4-GB flash storage drive
Optical drive
Supports 9.5-mm (2.5-inch) serial ATA (SATA) hard drives
160-GB, 7200-rpm
160-GB, 5400-rpm
120-GB, 7200-rpm
120-GB, 5400-rpm
Supports external USB optical drive only
1
Category Description
Diskette drive
Audio
Stereo speakers (2)
Intergrated stereo microphones (2)
Webcam
Modem
Ethernet
S3/S4/S5 wake on LAN: DC - no
S3/S4/S5 wake on LAN: AC - yes
Wireless Integrated WLAN options by way of wireless module:
2 WLAN antennae built into display assembly
Support for no-WLAN option
Support for the following WLAN formats:
Supports external USB diskette drive only
HD audio - AD1984
Optional integrated VGA webcam
Supports external USB modem only
Broadcom 5788 10/100/1000 LAN
Broadcom 4311AG 802.11a/b/g WLAN module
Broadcom BCM4312 802.11b/g WLAN module
Integrated personal area network (PAN) options by way of Bluetooth® module:
Support for no-WPAN option
Broadcom Bluetooth 2.0+EDR
External media card
SD/MMC Card Reader supporting Secure Digital (SD) Memory Card and MultiMediaCard (MMC)
Ports
Audio-out (stereo headphone)
RJ-45 (Ethernet, includes link and activity lights)
USB (non-powered)
USB (powered)
VGA (Dsub 15-pin) supporting 1920 × 1440 external resolution at 75-GHz (hot plug/unplug with auto-detect)
2-pin AC power
Keyboard/ pointing devices
Windows Vista® Start button
TouchPad, with 2 TouchPad buttons and vertical scrolling (taps enabled as default)
Power requirements
One ExpressCard/54 slot
Audio-in (stereo microphone)
25.4-cm (10.0-inch) keyboard with embedded numeric keypad
65-W AC adapter with localized cable plug support (3-wire plug, supports 2-pin DC connector)
6-cell, 55-Wh Li-ion battery
2Chapter 1 Product description
Category Description
3-cell, 28-Wh Li-ion battery
Security
HP 3D DriveGuard
Operating system
Windows Vista® Basic 32 with Office 2007 Ready
Windows Vista Business 32 with Office 2007 Ready
Windows® XP Professional
Windows XP Home (People's Republic of China only)
Novell SuSE SLED 10
DR DVD Windows Vista Home Basic
OS DVD Windows Vista Business
DR DVD/OS DVD Windows XP Pro
Novell SuSE SLED 10
Serviceability End-user replaceable parts:
AC adapter
Battery (system)
Supports Kensington security lock
Preinstalled:
Restore media:
Hard drive
Memory module
3
2

External component identification

Top components

Display

Item Component Function
(1)
(2)
(3)
(4)
Speakers (2) Produce sound.
Wireless antennae (2) Send and receive signals from one or more wireless
Internal microphones (2) Record sound.
Webcam (select models only)
4Chapter 2 External component identification
devices.
NOTE: The antennae are not visible from the outside of
the computer.
NOTE: If there is a microphone icon next to each
microphone opening, your computer has internal microphones.
Records and plays back webcam video.
Includes streaming video options and special effects
for adding frames, filters, and emoticons to snapshots and video.

Keys

Item Component Function
Captures single frame or burst webcam snapshots.
Connects to e-mail photos and video.
Item Component Function
(1)
(2)
(3)
(4)
(5)
(6)
esc key Displays system information when pressed in combination
with the fn key.
fn key Executes frequently used system functions when pressed in
combination with a function key or the esc key.
Windows logo key Displays the Windows Start menu.
Windows applications key Displays a shortcut menu for items beneath the pointer.
Embedded numeric keypad keys Can be used like the keys on an external numeric keypad.
Function keys Execute frequently used system functions when pressed in
combination with the fn key.
Top components 5

TouchPad

Item Component Function
(1)
(2)
(3)
(4)
(5)
*This table describes factory settings. To view or change pointing device preferences, select Start > Control Panel > Hardware and Sound > Mouse.
TouchPad on/off button Enables/disables the TouchPad.
Left TouchPad button* Functions like the left button on an external mouse.
TouchPad* Moves the pointer and selects or activates items on the
screen.
TouchPad scroll zone Scrolls up or down.
Right TouchPad button* Functions like the right button on an external mouse.
6Chapter 2 External component identification

Front components

Item Component Function
(1)
(2)
(3)
(4)
Power light Blue: The computer is on.
Blinking: The computer is in the Sleep state.
Off: The computer is off or in Hibernation.
Power switch
Drive light Blinking: The hard drive is being accessed.
Wireless light
When the computer is off, slide the switch to turn on
the computer.
When the computer is on, slide the switch briefly to
initiate Hibernation.
When the computer is in the Sleep state, slide the
switch briefly to exit Sleep.
When the computer is in Hibernation, slide the switch
briefly to exit Hibernation.
If the computer has stopped responding and Windows® shutdown procedures are ineffective, slide and hold the power switch for at least 5 seconds to turn off the computer.
To learn more about your power settings, select Start >
Control Panel > System and Maintenance > Power Options.
Blue: An integrated wireless device, such as a wireless
local area network (WLAN) device, the HP Broadband Wireless Module, and/or a Bluetooth® device, is on.
(5)
Amber: All wireless devices are off.
NOTE: The wireless light turns amber when the computer
turns on, but all wireless devices are off.
Wireless switch Turns the wireless feature on or off, but does not create a
wireless connection.
NOTE: To establish a wireless connection, a wireless
network must already be set up.
Front components 7

Right-side components

Item Component Function
(1)
(2)
(3)
(4)
(5)
(6)
(7)
ExpressCard slot Supports optional ExpressCards 54.
SD Card Reader Supports the following optional digital card formats:
Secure Digital (SD) Memory Card
MultiMediaCard (MMC)
USB port Connects an optional USB device.
RJ-45 (network) jack Connects a network cable.
Battery light
Power connector Connects an AC adapter.
Security cable slot Attaches an optional security cable to the computer.
Amber: A battery is charging.
Blue: A battery is close to full charge capacity.
Blinking amber: A battery that is the only available
power source has reached a low battery level.
If the computer is plugged into an external power
source, the light turns off when all batteries in the computer are fully charged. If the computer is not plugged into an external power source, the light stays off until the battery reaches a low battery level.
NOTE: The security cable is designed to act as a
deterrent, but it may not prevent the computer from being mishandled or stolen.
8Chapter 2 External component identification

Left-side components

Item Component Function
(1)
(2)
(3)
(4)
(5)
External monitor port Connects an external VGA monitor or projector.
Vent Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Powered USB port Provides power to a USB device, such as an optional
external MultiBay or an optional external optical drive, if used with a powered USB cable.
Audio-in (microphone) jack Connects an optional computer headset microphone,
stereo array microphone, or monaural microphone.
Audio-out (headphone) jack Produces sound when connected to optional powered
stereo speakers, headphones, ear buds, a headset, or television audio.
Left-side components 9

Bottom components

Item Component Function
(1)
(2)
(3)
(4)
Battery release latches (2) Release the battery from the battery bay.
Battery bay Holds the battery.
Service tag Provides the product brand and series name, serial number
(s/n), and product number (p/n) of your computer. Have this information available when you contact technical support.
Vents (3) Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
10 Chapter 2 External component identification
3

Illustrated parts catalog

Serial number location

When ordering parts or requesting information, provide the computer serial number and model number located on the bottom of the computer.
Serial number location 11

Computer major components

Item Description Spare part
(1) 8.9-inch, WXGA display assemblies (include 2 microphones, 2 speakers, and 2 WLAN antenna transceivers and
cables)
For use only with computer models equipped with camera module
12 Chapter 3 Illustrated parts catalog
number
483384-001
Item Description Spare part
number
For use only with computer models not equipped camera module 482278-001
(2) Keyboards
For use in France 482280-051
For use in French Canada 482280-121
For use in Germany 482280-041
For use in Italy 482280-061
For use in Japan 482280-291
For use in Latin America 482280-161
For use in Portugal 482280-131
For use in South Korea 482280-AD1
For use in Spain 482280-071
For use in Taiwan 482280-AB1
For use in Thailand 482280-281
For use in the United Kingdom 482280-031
For use in the United States 482280-001
(3) Memory modules (PC2-5300, 667-MHz, DDR2)
For use in Brazil 482280-201
2048-MB 417506-001
1024-MB 414046-001
512-MB 414045-001
(4) Mass storage devices
160-GB, 5400-rpm 482269-001
120-GB, 7200-rpm 482268-001
120-GB, 5400-rpm 482267-001
(5) Top cover (includes power on switch board and cable, TouchPad board and cable, and
(6) Audio board
(7) Fan/heat sink (includes replacement thermal material)
(8a)
Hard drives (include bracket and SATA connector)
160-GB, 7200-rpm 482271-001
4-GB solid-state drive (includes bracket and SATA connector)
wireless on/off switch board and cable)
Bracket Kit (see Bracket Kit on page 16 for more Bracket Kit spare part number information)
Audio/USB connector bracket
482272-001
482265-001
482274-001
482279-001
482266-001
Computer major components 13
Item Description Spare part
number
(8b)
(8c)
(9a)
(9b)
(9c)
(10) Broadcom Bluetooth modules (do not include Bluetooth module cable)
For use only in Japan and Asia Pacific countries and regions 450066-001
(11) System boards (include ExpressCard assembly, fan/heat sink, processor, RTC battery, and replacement thermal
Equipped with 1.2-GHz processor 482276-001
Equipped with 1.0-GHz processor 482275-001
ExpressCard assembly bracket
USB/RJ-45 connector bracket
Plastics/Cable Kit (see Plastics/Cable Kit on page 17 for more Plastics/Cable Kit spare part number information)
ExpressCard slot bezel
SD Card slot bezel
Bluetooth module cable
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth module cable is
included in the Plastics/Cable Kit, spare part number 483381-001. See Plastics/Cable Kit spare part number information.
For use in all countries and regions except Japan and Asia Pacific countries and regions 398393-002
material)
Equipped with 1.6-GHz processor 482277-001
Plastics/Cable Kit on page 17 for more
483381-001
(12) RTC battery
(13) WLAN modules
Broadcom 4311AG 802.11a/b/g WLAN modules:
For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands,
and the United States
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia,
Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic,
East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji,
Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania,
Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco,
Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands,
New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal,
the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea,
Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga,
449137-001
441075-001
441075-002
14 Chapter 3 Illustrated parts catalog
Item Description Spare part
number
Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
For use in Japan
Broadcom BCM4312 802.11b/g WLAN modules:
For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands,
and the United States
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
441075-291
459263-001
459263-002
(14) Base enclosure (includes 4 rubber feet)
(15) Batteries
3-cell, 28-Wh Li-ion battery 482262-001
Rubber Kit (not illustrated, contains 4 computer feet)
6-cell, 55-Wh Li-ion battery 482263-001
482264-001
483382-001
Computer major components 15

Bracket Kit

Item Description Spare part number
(1)
(2)
(3)
Bracket Kit:
ExpressCard assembly bracket
USB/RJ-45 connector bracket
Audio/USB connector bracket
482266-001
16 Chapter 3 Illustrated parts catalog

Plastics/Cable Kit

Item Description Spare part number
Plastics/Cable Kit:
ExpressCard slot bezel
(1)
SD Card slot bezel
(2)
Bluetooth module cable
(3)

Miscellaneous parts

Description Spare part number
65-W HP Smart AC adapter
Power cords:
For use in Australia
For use in Brazil 246959-201
For use in Denmark 246959-081
For use in Europe, the Middle East, and Africa 246959-021
For use in Israel 246959-BB1
For use in Italy 246959-061
483381-001
463958-001
246959-011
For use in Japan 246959-291
For use in South Korea 246959-AD1
For use in Switzerland 246959-AG1
For use in the United Kingdom 246959-031
Plastics/Cable Kit 17
Description Spare part number
For use the United States 246959-001
Screw Kit
Phillips PM2.0×3.0 screw
Torx8 T8M2.5×10.0 screw
Torx8 T8M2.5×5.0 screw
Torx8 T8M2.0×6.0 screw
Torx8 T8M2.0×4.0 screw

Sequential part number listing

Spare part number
246959-001 Power cord for use in the United States
246959-011 Power cord for use in Australia and New Zealand
246959-021 Power cord for use in Europe, the Middle East, and Africa
246959-031 Power cord for use in the United Kingdom
246959-061 Power cord for use in Italy
246959-081 Power cord for use in Denmark
Description
483383-001
246959-201 Power cord for use in Brazil
246959-291 Power cord for use in Japan
246959-AD1 Power cord for use in South Korea
246959-AG1 Power cord for use in Switzerland
246959-BB1 Power cord for use in Israel
398393-002 Bluetooth module for use in all countries and regions except Japan and Asia Pacific countries and regions
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth module
cable is included in the Plastics/Cable Kit, spare part number 483381-001. See
on page 17 for more Plastics/Cable Kit spare part number information.
414045-001 512-MB memory module (PC2-5300, 667-MHz, DDR2)
414046-001 1024-MB memory module (PC2-5300, 667-MHz, DDR2)
417506-001 2048-MB memory module (PC2-5300, 667-MHz, DDR2)
441075-001 Broadcom 4311AG 802.11a/b/g WLAN module for use in Canada, the Cayman Islands, Guam, Puerto Rico,
the U.S. Virgin Islands, and the United States
441075-002 Broadcom 4311AG 802.11a/b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola,
Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France,
Plastics/Cable Kit
18 Chapter 3 Illustrated parts catalog
Spare part number
441075-291 Broadcom 4311AG 802.11a/b/g WLAN module for use in Japan
449137-001 RTC battery
450066-001 Bluetooth module for use only in Japan and Asia Pacific countries and regions
459263-001 Broadcom BCM4312 802.11b/g WLAN module for use in Canada, the Cayman Islands, Guam, Puerto Rico,
Description
French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth module
cable is included in the Plastics/Cable Kit, spare part number 483381-001. See
on page 17 for more Plastics/Cable Kit spare part number information.
the U.S. Virgin Islands, and the United States
Plastics/Cable Kit
459263-002 Broadcom BCM4312 802.11b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola,
463958-001 65-W HP Smart AC adapter
482262-001 3-cell, 28-Wh Li-ion battery
482263-001 6-cell, 55-Wh Li-ion battery
482264-001 Base enclosure (includes 4 rubber feet)
Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
482265-001 Top cover (includes power on switch board and cable, TouchPad board and cable, and wireless on/off switch
board and cable)
482266-001 Bracket Kit (see Bracket Kit on page 16 for more Bracket Kit spare part number information)
482267-001 120-GB, 5400-rpm hard drive (includes bracket and SATA connector)
Sequential part number listing 19
Spare part number
482238-001 120-GB, 7200-rpm hard drive (includes bracket and SATA connector)
482269-001 160-GB, 5400-rpm hard drive (includes bracket and SATA connector)
482271-001 160-GB, 7200-rpm hard drive (includes bracket and SATA connector)
482272-001 4-GB solid-state drive (includes bracket and SATA connector)
482274-001 Audio board
482275-001 System board equipped with 1.0-GHz processor (includes ExpressCard assembly, fan/heat sink, processor, RTC
482276-001 System board equipped with 1.2-GHz processor (includes ExpressCard assembly, fan/heat sink, processor, RTC
482277-001 System board equipped with 1.6-GHz processor (includes ExpressCard assembly, fan/heat sink, processor, RTC
482278-001 8.9-inch, WXGA display assembly for use only with computer models not equipped camera module (includes 2
482279-001 Fan/heat sink (includes replacement thermal material)
482280-001 Keyboard for use in the United States
482280-031 Keyboard for use in the United Kingdom
Description
battery, and replacement thermal material)
battery, and replacement thermal material)
battery, and replacement thermal material)
microphones, 2 speakers, and 2 WLAN antenna transceivers and cables)
482280-041 Keyboard for use in Germany
482280-051 Keyboard for use in France
482280-061 Keyboard for use in Italy
482280-071 Keyboard for use in Spain
482280-121 Keyboard for use in French Canada
482280-131 Keyboard for use in Portugal
482280-161 Keyboard for use in Latin America
482280-201 Keyboard for use in Brazil
482280-281 Keyboard for use in Thailand
482280-291 Keyboard for use in Japan
482280-AB1 Keyboard for use in Taiwan
482280-AD1 Keyboard for use in South Korea
483381-001 Plastics/Cable Kit (see Plastics/Cable Kit on page 17 for more Plastics/Cable Kit spare part number
information)
483382-001 Rubber Kit (contains 4 computer feet)
483383-001 Screw Kit
483384-001 8.9-inch, WXGA display assembly for use only with computer models not equipped camera module (includes 2
microphones, 2 speakers, and 2 WLAN antenna transceivers and cables)
20 Chapter 3 Illustrated parts catalog
4

Removal and replacement procedures

Preliminary replacement requirements

Tools required

You will need the following tools to complete the removal and replacement procedures:
Flat-bladed screwdriver
Magnetic screwdriver
Phillips P0 and P1 screwdrivers
Torx8 T8 screwdriver

Service considerations

The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Preliminary replacement requirements 21
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and be sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective packaging and label the package “FRAGILE.”
22 Chapter 4 Removal and replacement procedures

Grounding guidelines

Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal cycle. Or the device may function normally for a while, then degrade in the internal layers, reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you area ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described in this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event 10% 40% 55%
Walking across carpet 35,000 V 15,000 V 7,500 V
Walking across vinyl floor 12,000 V 5,000 V 3,000 V
Motions of bench worker 6,000 V 800 V 400 V
Removing DIPS from plastic tube 2,000 V 700 V 400 V
Removing DIPS from vinyl tray 11,500 V 4,000 V 2,000 V
Removing DIPS from Styrofoam 14,500 V 5,000 V 3,500 V
Removing bubble pack from PCB 26,500 V 20,000 V 7,000 V
Packing PCBs in foam-lined box 21,000 V 11,000 V 5,000 V
Preliminary replacement requirements 23
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
Place items on a grounded surface before removing items from their containers.
Always be properly grounded when touching a component or assembly.
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized
equipment used for moving materials is wired to ground and that proper materials are selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
Cover the workstation with approved static-shielding material.
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these
items only at static-free workstations.
Avoid contact with pins, leads, or circuitry.
Turn off power and input signals before inserting or removing connectors or test equipment.
24 Chapter 4 Removal and replacement procedures
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can
be used at standing workstations and are compatible with most types of shoes or boots. On conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance between the operator and ground. To be effective, the conductive strips must be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
Antistatic tape
Antistatic smocks, aprons, and sleeve protectors
Conductive bins and other assembly or soldering aids
Nonconductive foam
Conductive tabletop workstations with ground cords of one megohm resistance
Static-dissipative tables or floor mats with hard ties to the ground
Field service kits
Static awareness labels
Material-handling packages
Nonconductive plastic bags, tubes, or boxes
Metal tote boxes
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material Use Voltage protection level
Antistatic plastic Bags 1,500 V
Carbon-loaded plastic Floor mats 7,500 V
Metallized laminate Floor mats 5,000 V
Preliminary replacement requirements 25

Unknown user password

If the computer you are servicing has an unknown user password, follow these steps to clear the password:
NOTE: These steps also clear CMOS.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the real-time clock (RTC) battery (see
5.
Wait approximately 5 minutes.
6.
Replace the RTC battery and reassemble the computer.
7.
Connect AC power to the computer. Do not reinsert any batteries at this time.
8.
Turn on the computer.
9.
All passwords and all CMOS settings have been cleared.
Battery on page 29).
RTC battery on page 47).
26 Chapter 4 Removal and replacement procedures

Component replacement procedures

This chapter provides removal and replacement procedures.
There are as many as 31 screws, in 5 different sizes, that must be removed or replaced when servicing the computer. Make special note of each screw size and location during removal and replacement.

Serial number

Report the computer serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the computer.
Component replacement procedures 27

Computer feet

The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare part number 483382-001. There are 4 rubber feet that are installed on the base enclosure in the locations illustrated below. The rubber feet are attached to the base enclosure by tethers.
28 Chapter 4 Removal and replacement procedures

Battery

Description Spare part number
6-cell, 55-Wh Li-ion battery 482262-001
3-cell, 28-Wh Li-ion battery 482263-001
Before disassembling the computer, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Remove the battery:
Turn the computer upside down on a flat surface, with the battery bay toward you.
1.
2. Slide the battery release latches (1) to release the battery.
3. Remove the battery (2) from the computer.
Install the battery by inserting it into the battery bay until you hear a click.
Component replacement procedures 29

Keyboard

Keyboards for use in the following countries or regions:
Country or region: Spare part number Country or region: Spare part number
Brazil 482280-201 Portugal 482280-131
France 482280-051 South Korea 482280-AD1
French Canada 482280-121 Spain 482280-071
Germany 482280-041 Taiwan 482280-AB1
Italy 482280-061 Thailand 482280-281
Japan 482280-291 The United Kingdom 482280-031
Latin America 482280-161 The United States 482280-001
Before removing the keyboard, follow these steps:
1.
2.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Battery on page 29).
Remove the keyboard:
Remove the three Phillips PM2.0×3.0 screws that secure the keyboard to the computer.
1.
Turn the computer display-side up, with the front toward you.
2.
Open the computer as far as possible.
3.
30 Chapter 4 Removal and replacement procedures
4. Lift the rear edge of the keyboard (1) until it rests at an angle, and then slide it back (2) until it rests
on the display assembly.
5. Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and
disconnect the keyboard cable (2) from the system board.
Remove the keyboard.
6.
Reverse this procedure to install the keyboard.
Component replacement procedures 31

Memory module

Description Spare part number
2048-MB (PC2-5300, 667-MHz, DDR2) 417506-001
1024-MB (PC2-5300, 667-MHz, DDR2) 414046-001
512-MB (PC2-5300, 667-MHz, DDR2) 414045-001
Before removing the memory module, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the keyboard (see
5.
Battery on page 29).
Keyboard on page 30).
Remove the memory module:
1. Spread the retaining tabs (1) on each side of the memory module slot to release the memory module.
(The edge of the module opposite the slot rises away from the computer.)
2. Remove the memory module (2) by pulling the module away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect installation into the
memory module slot.
Reverse this procedure to install a memory module.
32 Chapter 4 Removal and replacement procedures

Mass storage device

NOTE: All hard drive and solid-state drive spare part kits include a bracket and SATA adapter.
Description Spare part number
SATA hard drives:
160-GB, 7200-rpm hard drive
160-GB, 5400-rpm hard drive 482269-001
120-GB, 7200-rpm hard drive 482268-001
120-GB, 5400-rpm hard drive 482267-001
4-GB SATA flash module drive 482272-001
482271-001
Before removing the hard drive or solid-state drive, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the keyboard (see
5.
Battery on page 29).
Keyboard on page 30).
Remove the hard drive or solid-state drive:
1. Disconnect the drive cable (1) from the connector on the system board (2).
2. Remove the Torx8 T8M2.5×5.0 screw (1) and the two Torx8 T8M2.0×6.0 screws (2) that secure
the drive to the computer.
3. Grasp the Mylar tab (3) on the drive and slide the drive (4) to the left to release it from the drive
bay.
Component replacement procedures 33
4. Remove the drive (5) from the drive bay.
Reverse this procedure to install the hard drive or solid-state drive.
34 Chapter 4 Removal and replacement procedures

Top cover

Description Spare part number
Top cover 482265-001
Before removing the top cover, follow these steps:
1.
2.
3.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the keyboard (see
5.
Remove the hard drive or solid-state drive (see
6.
Battery on page 29).
Keyboard on page 30).
Mass storage device on page 33).
Remove the top cover:
Turn the computer upside down, with the front toward you.
1.
2. Use a thin, flat tool to release the four rubber feet (1).
CAUTION: The rubber feet are attached to the base enclosure by tethers. Exercise caution when
releasing the rubber feet to prevent damaging the feet.
3. Remove the three Torx8 T8M2.5×10.0 screws (2) and the Torx8 T8M2.0×4.0 screw (3) that secure
the top cover to the base enclosure.
Turn the computer right-side up, with the front toward you.
4.
Open the computer as far as possible.
5.
6. Remove the Torx8 T8M2.5×10.0 screw (1) that secures the top cover to the base enclosure.
Component replacement procedures 35
7. Lift the rear edge of the top cover (2) and swing it up and forward until it rests upside down in front
of the computer.
8. Disconnect the power switch board cable (1) from the system board.
9. Release the ZIF connector (2) to which the TouchPad cable is connected and disconnect the TouchPad
cable (3) from the system board.
10. Disconnect the wireless on/off switch board cable (4) from the system board.
Remove the top cover.
11.
Reverse this procedure to install the top cover.
36 Chapter 4 Removal and replacement procedures

Audio board

Description Spare part number
Audio board 482274-001
Before removing the audio board, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Keyboard (see
a.
Hard drive or solid-state drive (see
b.
Top cover (see
c.
Battery on page 29).
Keyboard on page 30)
Mass storage device on page 33)
Top cover on page 35)
Remove the audio board:
Remove the Torx8 T8M2.0×6.0 screw that secures the audio board to the computer.
1.
2. Lift the audio board (1) to disconnect the audio board connector (2) from the system board.
Component replacement procedures 37
3. Disconnect the audio board cables (3) from the audio board.
Remove the audio board.
4.
Reverse this procedure to install the audio board.
38 Chapter 4 Removal and replacement procedures

Bluetooth module

NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth
module cable is included in the Plastics/Cable Kit, spare part number 483381-001. See
Kit on page 17 for more Plastics/Cable Kit spare part number information.
Description Spare part number
For use in all countries and regions except Japan and Asia Pacific countries and regions 398393-002
For use only Japan and Asia Pacific countries and regions 450066-001
Before removing the Bluetooth module, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Plastics/Cable
Remove the battery (see
4.
Remove the following components:
5.
Keyboard (see
a.
Hard drive or solid-state drive (see
b.
Top cover (see
c.
Audio board (see
d.
Battery on page 29).
Keyboard on page 30)
Mass storage device on page 33)
Top cover on page 35)
Audio board on page 37)
Remove the Bluetooth module:
1. Detach the Bluetooth module (1) from the system board.
NOTE: The Bluetooth module is attached to the system board by double-sided tape.
Component replacement procedures 39
2. Disconnect the Bluetooth module cable (2) from the Bluetooth module.
Remove the Bluetooth module.
3.
Reverse this procedure to install the Bluetooth module.
40 Chapter 4 Removal and replacement procedures

System board

NOTE: All system board spare part kits include an ExpressCard assembly, fan/heat sink, processor,
RTC battery, and replacement thermal material).
Description Spare part number
Equipped with 1.6-GHz processor 482277-001
Equipped with 1.2-GHz processor 482276-001
Equipped with 1.0-GHz processor 482275-001
Before removing the system board, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Keyboard (see
a.
Hard drive (see
b.
Top cover (see
c.
Audio board (see
d.
Battery on page 29).
Keyboard on page 30)
Mass storage device on page 33)
Top cover on page 35)
Audio board on page 37)
When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board:
Memory module (see
WLAN module (see
Memory module on page 32)
WLAN module on page 45)
Component replacement procedures 41
Remove the system board:
Disconnect the following cables from the system board:
1.
(1) Display panel cable
(2) Microphone cable
(3) Camera module cable (only on computer models equipped with webcam)
Remove the wireless antenna cables from the clips built onto the system board.
2.
3. Remove the seven Torx8 T8M2.0×6.0 screws (1) that secure the system board and the three system
board brackets to the base enclosure.
42 Chapter 4 Removal and replacement procedures
Remove the following brackets:
4.
(2) Audio/USB connector bracket
(3) ExpressCard assembly bracket
(4) USB/RJ-45 connector bracket
NOTE: The audio/USB connector bracket, ExpressCard assembly bracket, and USB/RJ-45
connector bracket are included in the Bracket Kit, spare part number 482266-001.
5. Flex the right side of the base enclosure (1) until the USB connector and RJ-45 jack (2) are clear of
the base enclosure.
6. Lift the right side of the system board (3), and then swing it up and to the left until it rests upside
down on the left side of the computer.
Component replacement procedures 43
Disconnect the WLAN antenna cables from the terminals on the WLAN module.
7.
NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The
white WLAN antenna cable is connected to the WLAN module “Aux” terminal.
Remove the system board.
8.
Reverse the preceding procedure to install the system board.
44 Chapter 4 Removal and replacement procedures

WLAN module

Description Spare part number
Broadcom 4311AG 802.11a/b/g WLAN modules:
For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands,
and the United States
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
For use in Japan
441075-001
441075-002
441075-291
Broadcom BCM4312 802.11b/g WLAN modules:
For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands,
and the United States
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
459263-001
459263-002
Component replacement procedures 45
Before removing the WLAN module, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Keyboard (see
a.
Hard drive or solid-state drive (see
b.
Top cover (see
c.
Audio board (see
d.
System board (see
e.
Remove the WLAN module:
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module
authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact technical support through Help and Support.
Turn the system board upside down, with the front toward you.
1.
2. Remove the Torx8 T8M2.5×5.0 screw (1) that secures the WLAN module to the system board. (The
edge of the module opposite the slot rises away from the computer.)
3. Remove the WLAN module (2) by pulling the module away from the slot at an angle.
Battery on page 29).
Keyboard on page 30)
Mass storage device on page 33)
Top cover on page 35)
Audio board on page 37)
System board on page 41)
NOTE: WLAN modules are designed with a notch (3) to prevent incorrect installation.
Reverse this procedure to install the WLAN module.
46 Chapter 4 Removal and replacement procedures

RTC battery

NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords
and CMOS settings to be cleared.
Description Spare part number
RTC battery 449137-001
Before removing the RTC battery, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Keyboard (see
a.
Hard drive or solid-state drive (see
b.
Top cover (see
c.
Audio board (see
d.
System board (see
e.
Battery on page 29).
Keyboard on page 30)
Mass storage device on page 33)
Top cover on page 35)
Audio board on page 37)
System board on page 41)
Remove the RTC battery:
Turn the system board upside down, with the front toward you.
1.
2. Disconnect the RTC battery cable (1) from the system board.
Component replacement procedures 47
3. Detach the RTC battery (2) from the system board.
NOTE: The RTC battery is attached to the system board with double-sided tape.
Remove the RTC battery.
4.
Reverse this procedure to install the RTC battery.
48 Chapter 4 Removal and replacement procedures

Fan/heat sink

Description Spare part number
Fan/heat sink 482279-001
Before removing the fan/heat sink, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Keyboard (see
a.
Hard drive or solid-state drive (see
b.
Top cover (see
c.
Audio board (see
d.
System board (see
e.
Battery on page 29).
Keyboard on page 30)
Mass storage device on page 33)
Top cover on page 35)
Audio board on page 37)
System board on page 41)
Remove the fan/heat sink:
Following the 1, 2, 3, 4, 5 sequence stamped into the fan/heat sink, remove the five Torx8
1.
T8M2.0×6.0 screws (1) that secure the fan/heat sink to the system board
Component replacement procedures 49
2. Remove the fan/heat sink (2).
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink and
system board components. Thermal grease is used on the video chip (1) and the surface of the fan/ heat sink (1) that contacts the video chip. Thermal tape is used on the processor (2) and the surface of the fan/heat sink (2) that contacts the processor. Replacement thermal material is included with all fan/heat sink and system board spare part kits.
Reverse this procedure to install the fan/heat sink.
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left side of
the computer.
The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to turn on automatically when high temperature conditions exist. These conditions are affected by high external temperatures, system power consumption, power management/battery conservation
50 Chapter 4 Removal and replacement procedures
configurations, battery fast charging, and software requirements. Exhaust air is displaced through the ventilation grill located on the left side of the computer.

Display assembly

NOTE: All display assembly spare part kits include 2 microphones, 2 speakers, and 2 WLAN antenna
transceivers and cables.
Description Spare part number
8.9-inch, WXGA display assembly for use only with computer models equipped with camera module 483384-001
8.9-inch, WXGA display assembly for use only with computer models not equipped with camera module
482278-001
Before removing the display assembly, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
1.
computer on, and then shut it down through the operating system.
Disconnect all external devices connected to the computer.
2.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
3.
then unplugging the AC adapter from the computer.
Remove the battery (see
4.
Remove the following components:
5.
Keyboard (see
a.
Hard drive or solid-state drive (see
b.
Top cover (see
c.
Audio board (see
d.
System board (see
e.
Battery on page 29).
Keyboard on page 30)
Mass storage device on page 33)
Top cover on page 35)
Audio board on page 37)
System board on page 41)
Disconnect the wireless antenna cables from the WLAN module (see
6.
WLAN module on page 45).
Remove the display assembly:
1. Remove the wireless antenna cables (1) from the clips and routing channels built into the base
enclosure.
CAUTION: The display assembly will be unsupported when the following screws are removed. To
prevent damage to the display assembly, support it before removing the screws.
2. Remove the four Torx8 T8M2.5×10.0 screws (2) and the two Torx8 T8M2.5×5.0 screws (3) that
secure the display assembly to the computer.
Component replacement procedures 51
3. Lift the display assembly (4) straight up and remove it.
Reverse this procedure to reassemble and install the display assembly.
52 Chapter 4 Removal and replacement procedures
5

Computer Setup

Starting Computer Setup

Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load.
NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your
computer.
NOTE: Pointing devices are not supported in Computer Setup. You must use the keyboard to navigate
and make selections.
NOTE: An external keyboard connected by USB can be used with Computer Setup only if USB legacy
support is enabled.
To start Computer Setup:
Turn on or restart the computer.
1.
Before your operating system opens and while the "F10 = ROM Based Setup" message is displayed
2.
in the lower-left corner of the screen, press f10.
Starting Computer Setup 53

Using Computer Setup

Navigating and selecting in Computer Setup

The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and System Configuration menus.
Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the
1.
"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.
Because Computer Setup is not operating system based, it does not support the TouchPad. Navigation and selection are by keystroke:
To choose a menu or a menu item, use the arrow keys.
To select an item, press enter.
To close open dialog boxes and return to the main Computer Setup screen, press esc.
To view navigation information, press f1.
To change the language, press f2.
2. Select the File, Security, or System Configuration menu.
To exit Computer Setup, choose one of the following methods:
3.
To exit Computer Setup without saving your preferences, use the arrow keys to select File > Ignore changes and exit. Then follow the instructions on the screen.
To save your preferences and exit Computer Setup, use the arrow keys to select File > Save changes and exit. Then follow the instructions on the screen.
Your preferences go into effect when the computer restarts.

Restoring factory settings in Computer Setup

To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the
1.
"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.
2. Use the arrow keys to select File > Restore defaults, and then press enter.
When the confirmation dialog box opens, press f10.
3.
4. To save your preferences and exit Computer Setup, use the arrow keys to select File > Save
changes and exit. Then follow the instructions on the screen.
Your preferences go into effect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the factory
settings.
54 Chapter 5 Computer Setup

Computer Setup menus

The menu tables in this section provide an overview of Computer Setup options.
NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your
computer.

File menu

Select To do this
System information
Restore defaults Replace the configuration settings in Computer Setup with the original factory
Ignore changes and exit Cancel any changes entered during the current session. Then exit and restart the
Save changes and exit Save any changes entered during the current session. Then exit and restart the

Security menu

NOTE: Some of the menu items listed in this section may not be supported by your computer.
Select To do this
Administrator password Enter, change, or delete a setup password.
Change administrator password Enter, change, or delete an Administrator password.
Password check
View identification information for the computer and the batteries in the system.
View specification information for the processor, cache and memory size,
system ROM, video revision, and keyboard controller version.
settings. (Password settings and security settings are not changed when you restore the factory settings.)
computer.
computer. Your changes go into effect when the computer restarts.
Enable/disable Always to always check for a password.
Enable Setup to set the password.
Password Options
DriveLock Passwords
Notebook hard drive password status Enable/disable hard drive password status visibility.
Enable/disable stringent security.
Enable/disable password requirement on computer restart.
Enable/disable DriveLock on any computer hard drive.
Change a DriveLock user password or master password.
NOTE: DriveLock settings are accessible only when you enter Computer Setup by
turning on (not restarting) the computer.
Computer Setup menus 55

System Configuration menu

NOTE: Some of the listed System Configuration options may not be supported by your computer.
Select To do this
Boot Options
Device Configurations
Set an f9 and f10 delay when starting up.
Set the Express Boot Popup delay in seconds.
Enable/disable internal network adapter boot and set the boot mode (PXE).
Enable/disable MultiBoot, which sets a boot order that can include most boot
devices in the system.
Set the boot order.
1st boot device: USB devices
2nd boot device: Notebook hard drive
3rd boot device: Notebook Ethernet
Swap the functions of the fn key and left ctrl key.
Enable/disable USB legacy support. When enabled, USB legacy support
allows the following:
Use of a USB keyboard in Computer Setup even when your operating
system is not running.
Startup from bootable USB devices, including a hard drive, diskette drive,
or optical drive connected by a USB port to the computer.
Enable/disable fan always on while connected to an AC outlet.
Enable/disable SATA Native Mode.
Built-In Device Options
Enable/disable embedded WLAN Device Radio.
Enable/disable embedded Bluetooth.
Enable/disable Wake on LAN.
Enable/disable Network Interface Controller (LAN)
NOTE: Always set the fan to 40% PWM while this item is enabled.
Enable/disable integrated camera.
Enable/disable Wake on LAN.
Enable/disable the ExpressCard slot.
56 Chapter 5 Computer Setup
6

Specifications

Computer specifications

Metric U.S.
Dimensions
Depth
Width 25.50 cm 10.04 in
Height (front to back) 2.67 to 3.30 cm 1.05 to 1.30 in
Weight
Equipped with a 3-cell battery, 120-GB hard drive, 1-GB memory, WLAN module, and 2 wireless antennae
Equipped with a 3-cell battery, 4-GB solid-state drive, 1-GB memory, WLAN module, and 2 wireless antennae
Input power
Operating voltage
Operating current 3.5 A
Temperature
Operating
Nonoperating -20°C to 60°C -4°F to 140°F
Relative humidity (noncondensing)
Operating
Nonoperating 5% to 95%
16.51 cm 6.50 in
1.27 kg 2.80 lbs
1.19 kg 2.63 lbs
18.5 V dc @ 3.5 A – 65 W
0°C to 35°C 32°F to 95°F
10% to 90%
Maximum altitude (unpressurized)
Operating
Nonoperating -15 m to 12,192 m -50 ft to 40,000 ft
Shock
Operating
Nonoperating 200 g, 2 ms, half-sine
Random vibration
Operating
-15 m to 3,048 m -50 ft to 10,000 ft
125 g, 2 ms, half-sine
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate
Computer specifications 57
Metric U.S.
Nonoperating 1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.

8.9-inch, WXGA display specifications

Metric U.S.
Dimensions
Height
Width 19.5 cm 7.68 in
Diagonal 22.7 cm 8.94 in
Number of colors
Contrast ratio
Brightness
Pixel resolution
Pitch
Format 1280 × 768
Configuration RGB vertical stripe
Backlight
Character display
Total power consumption
Viewing angle
11.7 cm 4.61 in
Up to 16.8 million
250:1 (typical)
200 nits (typical)
0.279 × 0.279 mm
Edge lit
80 × 25
4.0 W
+/-40 horizontal, +20/–40° vertical (typical)
58 Chapter 6 Specifications

Hard drive specifications

160-GB* 120-GB*
Dimensions
Height
Width 70 mm 70 mm
Weight 101 g 101 g
Interface type
Transfer rate
Security
Seek times (typical read, including setting)
Single track
Average 13 ms 13 ms
Maximum 24 ms 24 ms
Logical blocks
Disc rotational speed
Operating temperature
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive specifications may differ slightly.
NOTE: Certain restrictions and exclusions apply. Contact technical support for details.
9.5 mm 9.5 mm
SATA SATA
100 MB/sec 100 MB/sec
ATA security ATA security
3 ms 3 ms
312,560,640 234,420,480
7200 and 5400 rpm 7200 and 5400 rpm
5°C to 55°C (41°F to 131°F)
Hard drive specifications 59

System DMA specifications

Hardware DMA System function
DMA0 Not applicable
DMA1* Not applicable
DMA2* Not applicable
DMA3 Not applicable
DMA4 Direct memory access controller
DMA5* Available for ExpressCard
DMA6 Not assigned
DMA7 Not assigned
*ExpressCard controller can use DMA 1, 2, or 5.
60 Chapter 6 Specifications

System interrupt specifications

Hardware IRQ System function
IRQ0 System timer
IRQ1 Standard 101-/102-Key or Microsoft® Natural Keyboard
IRQ2 Cascaded
IRQ3 Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD
IRQ4 COM1
IRQ5* Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax
Modem with SmartCP
IRQ6 Diskette drive
IRQ7* Parallel port
IRQ8 System CMOS/real-time clock
IRQ9* Microsoft ACPI-compliant system
IRQ10* Intel USB UHCI controller—24C2
Intel 82852/82855 GM/GME Graphic Controller
Realtek RTL8139 Family PCI Fast Ethernet Controller
IRQ11 Intel USB EHCI controller—24CD
Intel USB UHCI controller—24C4
Intel USB UHCI controller—24C7
Intel Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
IRQ12 Synaptics PS/2 TouchPad
IRQ13 Numeric data processor
IRQ14 Primary IDE channel
IRQ15 Secondary IDE channel
*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
NOTE: ExpressCards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial
port may assert IRQ3 or IRQ4.
System interrupt specifications 61

System I/O address specifications

I/O address (hex) System function (shipping configuration)
000 - 00F DMA controller no. 1
010 - 01F Unused
020 - 021 Interrupt controller no. 1
022 - 024 Opti chipset configuration registers
025 - 03F Unused
02E - 02F 87334 “Super I/O” configuration for CPU
040 - 05F Counter/timer registers
044 - 05F Unused
060 Keyboard controller
061 Port B
062 - 063 Unused
064 Keyboard controller
065 - 06F Unused
070 - 071 NMI enable/RTC
072 - 07F Unused
080 - 08F DMA page registers
090 - 091 Unused
092 Port A
093 - 09F Unused
0A0 - 0A1 Interrupt controller no. 2
I/O Address (hex) System Function (shipping configuration)
0A2 - 0BF Unused
0C0 - 0DF DMA controller no. 2
0E0 - 0EF Unused
0F0 - 0F1 Coprocessor busy clear/reset
0F2 - 0FF Unused
100 - 16F Unused
170 - 177 Secondary fixed disk controller
178 - 1EF Unused
1F0 - 1F7 Primary fixed disk controller
1F8 - 200 Unused
201 JoyStick (decoded in ESS1688)
202 - 21F Unused
62 Chapter 6 Specifications
I/O address (hex) System function (shipping configuration)
220 - 22F Entertainment audio
230 - 26D Unused
26E - 26 Unused
278 - 27F Unused
280 - 2AB Unused
2A0 - 2A7 Unused
2A8 - 2E7 Unused
2E8 - 2EF Reserved serial port
2F0 - 2F7 Unused
2F8 - 2FF Infrared port
300 - 31F Unused
320 - 36F Unused
370 - 377 Secondary diskette drive controller
378 - 37F Parallel port (LPT1/default)
380 - 387 Unused
388 - 38B FM synthesizer—OPL3
38C - 3AF Unused
3B0 - 3BB VGA
3BC - 3BF Reserved (parallel port/no EPP support)
3C0 - 3DF VGA
3E0 - 3E1 ExpressCard controller in CPU
3E2 - 3E3 Unused
3E8 - 3EF Internal modem
3F0 - 3F7 “A” diskette controller
3F8 - 3FF Serial port (COM1/default)
CF8 - CFB PCI configuration index register (PCIDIVO-1)
CFC - CFF PCI configuration data register (PCIDIVO-1)
System I/O address specifications 63

System memory map specifications

Size Memory address System function
640 KB 00000000-0009FFFF Base memory
128 KB 000A0000-000BFFFF Video memory
48 KB 000C0000-000CBFFF Video BIOS
160 KB 000C8000-000E7FFF Unused
64 KB 000E8000-000FFFFF System BIOS
15 MB 00100000-00FFFFFF Extended memory
58 MB 04800000-07FFFFFF Super extended memory
58 MB 04800000-07FFFFFF Unused
2 MB 08000000-080FFFFF Video memory (direct access)
4 GB 08200000-FFFEFFFF Unused
64 KB FFFF0000-FFFFFFFF System BIOS
64 Chapter 6 Specifications
7

Screw listing

This section provides specification and reference information for the screws and screw locks used in the computer. All screws listed in this section are available in the Screw Kit, spare part number 483383-001.

Phillips PM2.0×3.0 screw

Color Quantity Length Thread Head diameter
Silver 3 3.0 mm 2.0 mm 4.5 mm
Where used: 3 screws that secure the keyboard to the computer
Phillips PM2.0×3.0 screw 65

Torx8 T8M2.0×6.0 screw

Color Quantity Length Thread Head diameter
Silver 15 6.0 mm 2.0 mm 4.5 mm
Where used: 2 screws that secure the mass storage device to the computer
66 Chapter 7 Screw listing
Where used: One screw that secures the audio board to the system board
Where used:
(1) Three screws that secure the audio/USB connector bracket to the system board
(2) Two screws that secure the ExpressCard assembly bracket to the system board
(3) Two screws that secure the USB/RJ-45 connector bracket to the system board
Torx8 T8M2.0×6.0 screw 67
Where used: 5 screws that secure the fan/heat sink to the system board
68 Chapter 7 Screw listing

Torx8 T8M2.5×5.0 screw

Color Quantity Length Thread Head diameter
Black 4 5.0 mm 2.5 mm 5.0 mm
Where used: One screw that secures the mass storage device to the computer
Torx8 T8M2.5×5.0 screw 69
Where used: One screw that secures the WLAN module to the system board
Where used: 2 screws that secure the display assembly to the base enclosure
70 Chapter 7 Screw listing

Torx8 T8M2.5×10.0 screw

Color Quantity Length Thread Head diameter
Silver 8 10.0 mm 2.5 mm 5.0 mm
Where used: 3 screws that secure the top cover to the computer
Where used: One screw that secures the top cover to the computer
Torx8 T8M2.5×10.0 screw 71
Where used: 4 screws that secure the display assembly to the base enclosure

Torx8 T8M2.0×4.0 screw

Color Quantity Length Thread Head diameter
Silver 1 4.0 mm 2.0 mm 4.5 mm
Where used: One screw that secures the top cover to the computer
72 Chapter 7 Screw listing
8

Backup and recovery—Windows Vista

Overview

To protect your information, the computer provides tools to back up individual files and folders or your entire hard drive. In case of system instability or failure, you can use the backup files to restore the contents of your computer.
When creating backups, HP recommends the following sequence:
Create a set of recovery discs of the entire hard drive as soon as possible after you set up your
1.
computer.
Schedule periodic backups to record changes made to your computer.
2.
In addition to manual backup-and-recovery tools, you can use Windows® System Recovery to automatically back up and restore your information. This feature automatically backs up changes made to your computer daily and also at important milestones, such as when you add a program or driver. Use this tool to restore the computer to a previous state without losing personal files or e-mails. You can also manually set restore points and change restore settings.

Creating recovery discs

After setting up the computer, create a set of recovery discs for the initial backup of the entire hard drive.
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
The recovery discs are used to start up (boot) the computer and recover the operating system and software to factory settings in case of system failure.
Note the following tips for creating recovery discs:
Connect the computer to AC power during the process.
Use any of the following types of discs (purchased separately): CD-R, CD-RW, DVD+R, DVD+R DL,
DVD-R, DVD-R DL, or DVD±RW. The discs you use will depend on the type of optical drive installed in your computer.
NOTE: DVDs and DVDs with double-layer (DL) support store more information than CDs and will
reduce the number of recovery discs required.
Number each disc before inserting it into the optical drive of the computer.
Overview 73
To create a set of recovery discs:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Click Back up computer.
Follow the on-screen instructions.
3.
NOTE: Windows includes the User Account Control feature to improve the security of your
computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.

Backing up your information

After you create the recovery discs for the initial backup of the entire hard drive, you should schedule automatic backups of your files. You should also back up your files before you modify the hardware or software.
Several types of backup are available in the Backup and Restore Center:
Individual files or folders
Restore points
Entire hard drive

Backup tips

Connect the computer to AC power during the backup process.
Store personal files in the Documents folder and back them up regularly.
Back up templates that are stored in their associated programs.
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of
your settings. The screen shot can be a time-saver if you have to reset your preferences.
To create a screen shot:
Display the screen you want to save.
1.
Copy the screen image.
2.
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3. Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
Save the document.
4.
74 Chapter 8 Backup and recovery—Windows Vista

Backing up individual files or folders

You can manually back up files or folders to the following locations:
Network drive
Optional external hard drive
Optical discs (CDs or DVDs)
NOTE: This process will take several minutes, depending on the size of the files and the speed of the
computer.
To manually back up individual files or folders:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Click Back up files. You will be prompted to select a destination for the backup files.
Follow the on-screen instructions.
3.
NOTE: Windows includes the User Account Control feature to improve the security of your
computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.

Backing up the entire hard drive

When you perform a backup of the entire hard drive, you are saving the full factory image, including the Windows operating system, software programs, all personal files and folders, and configuration settings.
You can back up a copy of the entire hard drive to either of the following locations:
Optional external hard drive
Optical discs (CDs or DVDs)
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
To back up your hard drive:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Click Back up computer. You will be prompted to select a destination for the backup files.
Follow the on-screen instructions.
3.
NOTE: Windows includes the User Account Control feature to improve the security of your computer.
You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.

Scheduling an automatic backup

You can schedule automatic backups for the entire system, for recovery points, or for specific files and folders. Backups can be scheduled at specific intervals (daily, weekly, or monthly).
Backing up your information 75
To schedule an automatic backup:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Click Change settings.
The Backup Status and Configuration Window opens.
3. Click Change backup settings. You will be prompted to select a destination for the backup files.
Follow the on-screen instructions.
4.
NOTE: Windows includes the User Account Control feature to improve the security of your
computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.

Creating system restore points

In addition to the manual backup-and-recovery tools, you can use Windows System Recovery to automatically back up and restore your information. This feature automatically creates restore points just before a significant change is made to your system, such as the installation of a program or driver. You can also set manual restore points.
NOTE: The first system restore point is a snapshot of the entire image that is automatically created the
first time you perform a backup. Subsequent recovery points make copies of changes made after that time.
HP recommends that you create manual restore points at the following times:
Before you add or extensively modify software or hardware
Periodically, whenever the system is performing optimally
NOTE: Recovering to an earlier restore point does not delete data files or e-mails created since that
restore point.
To create a system restore point:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. On the left side of the screen, click Create a restore point or change settings.
3. Click Create. You will be prompted to name this restore point.
Follow the on-screen instructions.
4.
NOTE: Windows includes the User Account Control feature to improve the security of your computer.
You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.

Performing a recovery

In case of hard drive failure or system instability, the computer provides tools to recover your files.
You can recover your information using the following methods:
76 Chapter 8 Backup and recovery—Windows Vista
NOTE: Have your backup files available. Some of these methods will prompt you for your backup files
stored on recovery discs or on a drive.
Recovering individual files that you have previously backed up using Backup and Restore Center
Restoring the computer to a previous state by using system restore points
Recovering individual files that you have previously backed up or the entire hard drive using f8
recovery tools:
NOTE: You can use these methods only if the Windows recovery partition has not been deleted.
Windows Recovery Environment (WinRE)
Recovery Manager
Recovering the entire hard drive using f11
NOTE: You can use this method only if the Windows recovery partition has not been deleted.
Recovering information using an operating system DVD (purchased separately)

Recovering individual files

To recover individual files using the Backup and Restore Center, follow these steps:
If possible, back up all personal files.
1.
2. Select Start > All Programs > Maintenance > Backup and Restore Center.
3. Click Restore files. You will be prompted to select the location of the backup files.
Follow the on-screen instructions.
4.
NOTE: Windows includes the User Account Control feature to improve the security of your
computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.

Restoring the computer to a previous state

Your computer automatically creates restore points daily (depending on your computer activity) and when you make a major change to the computer, such as adding software or a new driver. If you decide to reverse changes made to the computer, you can revert back to a previous restore point.
To access a restore point:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Click Restore my computer to an earlier time. A calendar is displayed to help you find dates
associated with your restore points.
Select the restore point to revert to.
3.
NOTE: If you do not use your computer every day, some days may not have restore points.
Performing a recovery 77

Recovering information using f8 recovery tools

You can recover individual files or the entire hard drive using the recovery discs that you previously created or an optional external hard drive where you have backed up your information.
The following tools will help you recover your information:
Windows Recovery Environment (WinRE)
Recovery Manager
NOTE: You can use these recovery methods only if the Windows recovery partition has not been
deleted.
Recovering information using Windows Recovery Environment (WinRE)
Windows Recovery Environment (WinRE) can perform a recovery from either an optional external hard drive where you have backed up your information or from recovery discs that you previously created.
CAUTION: Using Windows Recovery Environment (WinRE) will completely erase hard drive contents
and reformat the hard drive. All files you have created and any software installed on the computer will be permanently removed. When reformatting is complete, the recovery process will restore the operating system, as well as the drivers, software, and utilities from the backup used for recovery.
To initiate recovery using WinRE, follow these steps:
NOTE: This process will take several minutes.
If possible, back up all personal files.
1.
Restart the computer, and then press f8 before the Windows operating system loads.
2.
3. Select Repair your computer.
NOTE: The “Repair your computer” option is displayed only if the Windows recovery partition has
not been deleted. If the option is not displayed, see
operating system DVD (purchased separately) on page 79.
Follow the on-screen instructions.
4.
5. Click Next.
6. Select your user name, type your password (if applicable), and then click OK.
If you are using recovery discs, insert the last disc of the recovery disc backup set.
7.
NOTE: Inserting the last disc of the backup set confirms the presence of a valid backup. If you
insert any other disc, the backup will not be recognized.
– or –
If you are using an optional external hard drive, connect it to the computer.
8. Click Windows Complete PC Restore.
Recovering information using a Windows Vista
Follow the on-screen instructions.
9.
78 Chapter 8 Backup and recovery—Windows Vista
Recovering information using Recovery Manager
If other methods do not work, you can recover your hard drive (in its factory state) as a last resort:
CAUTION: Using Recovery Manager will completely erase hard drive contents and reformat the hard
drive. All files you have created and any software installed on the computer will be permanently removed. Recovery Manager reinstalls the operating system and HP programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled.
If possible, back up all personal files.
1.
Restart the computer, and then press f8 before the Windows operating system loads.
2.
3. Select Repair your computer.
NOTE: The “Repair your computer” option is displayed only if the Windows recovery partition has
not been deleted. If the option is not displayed, see
operating system DVD (purchased separately) on page 79.
Follow the on-screen instructions.
4.
5. Click Next.
6. Select your user name, type your password (if applicable), and then click OK.
7. Click HP Recovery Manager.
Recovering information using a Windows Vista
Follow the on-screen instructions.
8.

Recovering information using a Windows Vista operating system DVD (purchased separately)

You can purchase a Windows Vista® operating system DVD to reboot the computer and repair the operating system. During the restore process, you will be prompted for your entire drive backup files. Make sure your most recent entire drive backup (stored on recovery discs or on an external drive) is easily accessible. To order a Windows Vista operating system DVD, go to your country or region, and follow the on-screen instructions.
CAUTION: Using a Windows Vista operating system DVD will completely erase hard drive contents
and reformat the hard drive. All files you have created and any software installed on the computer will be permanently removed. When reformatting is complete, the recovery process will help you restore the operating system, as well as drivers, software, and utilities.
To initiate recovery using a Windows Vista operating system DVD, follow these steps:
NOTE: This process will take several minutes.
If possible, back up all personal files.
1.
Restart the computer, and then insert the Windows Vista operating system DVD into your drive before
2.
the Windows operating system loads.
When prompted, press any keyboard key.
3.
http://www.hp.com/support, select
Follow the on-screen instructions.
4.
5. Click Next.
Performing a recovery 79
6. Select Repair your computer.
Follow the on-screen instructions.
7.
Remove the Windows Vista operating system DVD.
8.
If you are using recovery discs, insert the last disc of the recovery disc backup set.
9.
NOTE: Inserting the last disc of the backup set confirms the presence of a valid backup. If you
insert any other disc, the backup will not be recognized.
If you are using an optional external hard drive, connect it to the computer.
– or –
10. Click Windows Complete PC Restore.
Follow the on-screen instructions.
11.
80 Chapter 8 Backup and recovery—Windows Vista
9

Backup and recovery—Windows XP

Backing up your information

NOTE: You can recover only the files that you have previously backed up. HP recommends that you use
the Windows backup utility to create a hard drive backup as soon as you set up your computer.
With the Windows backup utility, you can perform the following tasks:
Backing up your information regularly to protect your important system files
Creating system recovery points that allow you to reverse undesirable changes to your computer by
restoring the computer to an earlier state
Scheduling backups at specific intervals or events
NOTE: The Windows backup utility backs up only data files. The operating system, drivers, and
programs are located on the operating system disc and System Recovery disc that are included with the computer.

When to backup

On a regularly scheduled basis
NOTE: Set reminders to back up your information periodically.
Before the computer is repaired or restored
Before you add or modify hardware or software

Backup suggestions

Connect the computer to external power before performing backup and recovery procedures.
Create system recovery points.
Store personal files in the My Documents folder and back up these folders periodically.
Back up templates stored in their associated programs.
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of
your settings. The screen shot can be a time saver if you have to reset your preferences.
Backing up your information 81
To copy the screen and paste it into a word-processing document:
Display the screen you want to save.
1.
Copy the screen image:
2.
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3. Open a word-processing document, click Edit > Paste.
The screen image is added to the document.
Save the document.
4.

Backing up individual files or folders

You can back up individual files or folders to an optional external hard drive or to a network drive.
NOTE: This process will take several minutes, depending on the file size and the speed of the computer.
To back up individual files or folders:
1. Select Start > All Programs > Accessories > System Tools > Backup.
The Backup or Restore Wizard page opens.
2. Click Next.
3. Click Backup files and settings, and then click Next.
Follow the on-screen instructions.
4.

Backing up all files and folders

When you back up all files and folders, you are saving all personal files and folders, all system files, and configuration settings at one time.
NOTE: When you back up all files and folders, this does not include the operating system or programs.
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
NOTE: A copy of the backup files can be stored on an optional external hard drive or on a network
drive.
To back up all files and folders:
1. Select Start > All Programs > Accessories > System Tools > Backup.
The Backup or Restore Wizard page opens.
2. Click Next.
3. Click Backup files and settings, and then click Next.
4. Click All information on this computer, and then click Next.
Follow the on-screen instructions.
5.
82 Chapter 9 Backup and recovery—Windows XP

Creating recovery points

When you back up system modifications since your last backup, you are creating system recovery points. This allows you to save a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you want to reverse subsequent changes made to your system.
NOTE: The first system recovery point, a snapshot of the entire image, is automatically created the first
time you perform a backup. Subsequent recovery points make copies of changes made after that time.
HP recommends that you create recovery points at the following times:
Before you add or extensively modify software or hardware
Periodically, whenever the system is performing optimally
NOTE: Recovering to an earlier recovery point does not affect data files or e-mails created since that
recovery point.
To create a system recovery point:
1. Select Start > All Programs > Accessories > System Tools > System Restore.
The System Restore window opens.
2. Click Create a new restore point, and then click Next.
Type a short description of the restore point. This will be used as the name of the restore point.
3.
4. Click Create.
Follow the on-screen instructions.
5.

Scheduling backups

You can schedule backups for the entire system, for recovery points, or for specific files and folders. Backups can be scheduled at specific intervals (daily, weekly, or monthly) or at specific events, such as at system restart or when you log on.
To schedule backups:
1. Select Start > All Programs > Accessories > System Tools > Schedule Tasks.
The Schedule Tasks window opens.
2. Double-click Add Scheduled Task, and then click Next.
3. Select Backup in the Application list, and then click Next.
Type a name for the backup, select when you want the backup to be performed, and then click
4.
Next.
5. Enter your user name, password, and password again to confirm. Click Next, and then click
Finish.
Backing up your information 83

Performing a recovery

The Windows backup utility helps you recover important files that you have previously backed up in case of system failure.
NOTE: To recover the operating system and programs, use the operating system disc and System
Restore disc that are included with the computer.

Initiating a recovery in Windows

To initiate a recovery in Windows, follow these steps:
If possible, back up all personal files.
1.
2. Select Start > All Programs > Accessories > System Tools > Backup.
The Backup or Restore Wizard page opens.
3. Click Restore files and settings, and the click Next.
Follow the on-screen instructions.
4.
84 Chapter 9 Backup and recovery—Windows XP
10

Connector pin assignments

Audio-out (headphone)

Pin Signal
1 Audio out, left channel
2 Audio out, right channel
3Ground

Audio-in (microphone)

Pin Signal
1 Audio signal in
2 Audio signal in
3Ground
Audio-out (headphone) 85

External monitor

Pin Signal
1 Red analog
2 Green analog
3 Blue analog
4 Not connected
5 Ground
6 Ground analog
7 Ground analog
8 Ground analog
9 +5 VDC
10 Ground
11 Monitor detect
12 DDC 2B data
13 Horizontal sync
14 Vertical sync
15 DDC 2B clock
86 Chapter 10 Connector pin assignments

RJ-45 (network)

Pin Signal
1 Transmit +
2 Transmit -
3 Receive +
4 Unused
5 Unused
6 Receive -
7 Unused
8 Unused

Universal Serial Bus

Pin Signal
1 +5 VDC
2 Data -
3 Data +
4Ground
RJ-45 (network) 87
11

Power cord set requirements

The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or region where the computer is used.

Requirements for all countries and regions

The requirements listed below are applicable to all countries and regions:
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
All power cord sets must be approved by an acceptable accredited agency responsible for evaluation
in the country or region where the power cord set will be used.
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating
of 125 or 250 V AC, as required by the power system of each country or region.
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard
Sheet C13 connector for mating with the appliance inlet on the back of the computer.
88 Chapter 11 Power cord set requirements

Requirements for specific countries and regions

Country/region Accredited agency Applicable note number
Australia EANSW 1
Austria OVE 1
Belgium CEBC 1
Canada CSA 2
Denmark DEMKO 1
Finland FIMKO 1
France UTE 1
Germany VDE 1
Italy IMQ 1
Japan METI 3
Korea EK 4
The Netherlands KEMA 1
Norway NEMKO 1
The People's Republic of China CCC 5
Sweden SEMKO 1
Switzerland SEV 1
Taiwan BSMI 4
The United Kingdom BSI 1
The United States UL 2
The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
1.
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding
2.
type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
3.
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and
4.
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and
5.
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
Requirements for specific countries and regions 89
12

Recycling

Battery

When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for computer battery disposal.

Display

WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this appendix can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight. Careful handling must be exercised when removing these components. When you remove these components, handle them carefully.
NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly
that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities, or see the Electronic Industries Alliance (EIA) Web site at
This section provides disassembly instructions for the display assembly. The display assembly must be disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE: The procedures provided in this appendix are general disassembly instructions. Specific details,
such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from one computer model to another.
http://www.eiae.org.
90 Chapter 12 Recycling
Perform the following steps to disassemble the display assembly:
1. Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.
2. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the
display bezel until the bezel disengages from the display assembly.
3. Remove the display bezel (3).
Display 91
4. Disconnect all display panel cables (1) from the display inverter and remove the inverter (2).
5. Remove all screws (1) that secure the display panel assembly to the display enclosure.
6. Remove the display panel assembly (2) from the display enclosure.
Turn the display panel assembly upside down.
7.
Remove all screws that secure the display panel frame to the display panel.
8.
9. Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display
panel frame.
92 Chapter 12 Recycling
Loading...