Hestan KRCR30OV, KRBL36BU, KRPR36TQ, KRWL24OV, KWCL24TQ Installation Manual

INDOOR PRESERVATION

Refrigerators, Freezers and Wine Storage

KRP / KRB / KRC / KFC / KWC / KRW

Installation Manual

EN

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY, OR DEATH.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.

Installation and service must be performed by a qualified installer or service agency.

DO NOT REPAIR, REPLACE OR REMOVE ANY PART OF THE APPLIANCE UNLESS
SPECIFICALLY RECOMMENDED IN THE MANUAL. IMPROPER INSTALLATION,
SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER
TO THIS MANUAL FOR GUIDANCE. ALL OTHER SERVICING SHOULD BE DONE BY A
QUALIFIED TECHNICIAN.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY
BEFORE INSTALLING OR USING YOUR APPLIANCE TO REDUCE
THE RISK OF FIRE, BURN HAZARD, OR OTHER INJURY. KEEP
THIS MANUAL FOR FUTURE REFERENCE.

SAFETY DEFINITIONS

DANGER. THIS INDICATES INFORMATION AND WARNINGS WHICH,
IF NOT OBSERVED, MAY COMPROMISE PERSONAL SAFETY OR DAMAGE
THE APPLIANCE.

DANGER OF ELECTROCUTION. THIS INDICATES INFORMATION AND

WARNINGS OF AN ELECTRICAL NATURE WHICH, IF NOT OBSERVED,

MAY COMPROMISE PERSONAL SAFETY OR DAMAGE THE APPLIANCE.

THIS HIGHLIGHTS GENERAL INFORMATION AND WARNINGS AND
INDICATES THAT DAMAGE TO THE APPLIANCE OR PROPERTY MAY
OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.

INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE.
HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

©2018 Hestan Commercial Corporation

TABLE OF CONTENTS

1 SAFETY PRECAUTIONS - BEFORE YOU BEGIN
2 MODEL NUMBERS
3

RATING LABEL
3 REGULATORY / CODE REQUIREMENTS
4 IMPORTANT CHILD SAFETY

LOCATION AND INSTALLATION

4
29 REQUIRED VENTILATION

TESTING AND INITIAL START-UP

30

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

When properly cared for, your Hestan appliance will provide safe, reliable service for many
years. When using this appliance, basic safety practices must be followed as outlined below.

IMPORTANT: Save these instructions for the local Utility Inspector’s use.

EN

INSTALLER: Please leave these Installation Instructions with the owner.

OWNER: Please retain these Installation Instructions for future reference.

This appliance is NOT designed for installation in manufactured (mobile) homes or
recreational park trailers. Do NOT install this appliance outdoors.

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing appliance. Failure to do
so can result in death or electrical shock.

ELECTRICAL GROUNDING

• This appliance must be grounded. Grounding reduces the risk of electric shock in the
event of a short circuit. Read the ELECTRICAL and WATER CONNECTIONS sections
of this manual for complete instructions.

• DO NOT ground to a gas pipe.

• DO NOT use an extension cord with this appliance.

• DO NOT have a fuse in the NEUTRAL or GROUNDING circuit. A fuse in the NEUTRAL
or GROUNDING circuit could result in an electrical shock.

©2018 Hestan Commercial Corporation

1

MODEL NUMBERS

REFRIGERATION MODELS

EN

Model No.

KRPR36 Bottom Mount Refrigerator, Top Compressor, Pro, Right Hinged, 36"
KRPL36 Bottom Mount Refrigerator, Top Compressor, Pro, Left Hinged, 36"
KRPR36-XX Bottom Mount Refrigerator, Top Compressor, Pro, Color, Right Hinged, 36"

KRPL36-XX Bottom Mount Refrigerator, Top Compressor, Pro, Color, Left Hinged, 36"
KRBR36 Bottom Mount Refrigerator, Bottom Compressor, Right Hinged, 36"
KRBL36 Bottom Mount Refrigerator, Bottom Compressor, Left Hinged, 36"
KRBR36-OV Bottom Mount Refrigerator, Bottom Compressor, Overlay, Right Hinged, 36"
KRBL36-OV Bottom Mount Refrigerator, Bottom Compressor, Overlay, Left Hinged, 36"
KRBR36-XX Bottom Mount Refrigerator, Bottom Compressor, Color, Right Hinged, 36"
KRBL36-XX Bottom Mount Refrigerator, Bottom Compressor, Color, Left Hinged, 36"
KRCR24 Refrigerator Column, Right Hinged, 24"
KRCL24 Refrigerator Column, Left Hinged, 24"
KRCR24-OV Refrigerator Column, Overlay, Right Hinged, 24"
KRCL24-OV Refrigerator Column, Overlay, Left Hinged, 24"
KRCR24-XX Refrigerator Column, Color, Right Hinged, 24"
KRCL24-XX Refrigerator Column, Color, Left Hinged, 24"
KRCR30 Refrigerator Column, Right Hinged, 30"
KRCL30 Refrigerator Column, Left Hinged, 30"
KRCR30-OV Refrigerator Column, Overlay, Right Hinged, 30"
KRCL30-OV Refrigerator Column, Overlay, Left Hinged, 30"
KRCR30-XX Refrigerator Column, Color, Right Hinged, 30"
KRCL30-XX Refrigerator Column, Color, Left Hinged, 30"

Description

FREEZER MODELS

Model No.

KFCR24 Freezer Column, Right Hinged, 24"
KFCL24 Freezer Column, Left Hinged, 24"
KFCR24-OV Freezer Column, Overlay, Right Hinged, 24"
KFCL24-OV Freezer Column, Overlay, Left Hinged, 24"
KFCR24-XX Freezer Column, Color, Right Hinged, 24"
KFCL24-XX Freezer Column, Color, Left Hinged, 24"

KFCR30 Freezer Column, Right Hinged, 30"
KFCL30 Freezer Column, Left Hinged, 30"
KFCR30-OV Freezer Column, Overlay, Right Hinged, 30"
KFCL30-OV Freezer Column, Overlay, Left Hinged, 30"
KFCR30-XX Freezer Column, Color, Right Hinged, 30"
KFCL30-XX Freezer Column, Color, Left Hinged, 30"

Description

©2018 Hestan Commercial Corporation

2

MODEL NUMBERS

WINE MODELS

(continued)

Model No. Description

KWCR24 Wine Column, Right Hinged, 24"
KWCL24 Wine Column, Left Hinged, 24"
KWCR24-OV Wine Column, Overlay, Right Hinged, 24"
KWCL24-OV Wine Column, Overlay, Left Hinged, 24"
KWCR24-XX Wine Column, Color, Right Hinged, 24"
KWCL24-XX Wine Column, Color, Left Hinged, 24"

KRWR24 Refrigerator with Wine, Right Hinged, 24"
KRWL24 Refrigerator with Wine, Left Hinged, 24"
KRWR24-OV Refrigerator with Wine, Overlay, Right Hinged, 24"
KRWL24-OV Refrigerator with Wine, Overlay, Left Hinged, 24"
KRWR24-XX Refrigerator with Wine, Color, Right Hinged, 24"
KRWL24-XX Refrigerator with Wine, Color, Left Hinged, 24"

NOTE: -XX indicates color model.

-BK for Stealth - Black

-YW for Sol - Yellow

-PP for Lush - Purple

-GG for Pacific Fog - Graphite Gray

-WH for Froth - White

-OR for Citra - Orange

-BU for Prince - Blue

EN

-RD for Matador - Red

-BG for Tin Roof - Burgundy

-GR for Grove - Green

-TQ for Bora Bora - Turquoise

RATING LABEL

The rating label contains important information about your
Hestan appliance such as the model and serial number and
electrical rating.

The rating label is located on the inside wall of the refrigerator.

HESTAN COMMERCIAL CORP.
ANAHEIM, CA - USA

ozFridge Gas Fill Charge

7

Quantité de Gaz Réfrigerateur

Freezer Gas Fill Charge
Quantité de Gaz Congélateur

Total Absorbed Current
Courant Absorbée Totale

Voltage
Tension

Frequency
Frequence

Refrigerant Gas Type
Type de Gaz Rèfrigerant

Made in Italy

TYPICAL RATING LABEL

MODEL

KRP36

0

CODE

A

1

FI24RC-RO

SER.NO./N° SERIE

V

115

XXXXXXXXXXX

Hz

60

R134a

3186660

ETL LISTED
CONFORMS TO
ANSI/UL STD 250
CERTIFIED TO CAN/CSA
STD C22.2 NO.63

REGULATORY / CODE REQUIREMENTS

Installation of this appliance must be made in accordance with local codes. In the

absence of local codes, this unit should be installed in accordance with the National Electrical
Code and local codes.

This appliance must be electrically grounded in accordance with local codes or in the absence
of local codes with the National Electrical Code

CSA C22.1

.

ANSI/NFPA 70

, or Canadian Electrical code

©2018 Hestan Commercial Corporation

3

IMPORTANT CHILD SAFETY

EN

DANGER: Risk of child entrapment. Before you throw away your old
refrigerator or freezer:

• Take off the doors

• Leave the shelves in place so that children may not easily climb
inside.

LOCATION AND INSTALLATION

PREPARATION

Before moving the refrigerator, protect any finished flooring to prevent damage.
Make sure that power can be provided to the location selected.

PACKAGED DIMENSIONS AND WEIGHTS

24” Models

30” Models

36” Models

w: 650 mm (25 5/8”) h: 2260 mm (89”) d: 800 mm (31 1/2”)
230 kg (507 lb)

w: 800 mm (31 1/2”) h: 2260 mm (89”) d: 800 mm (31 1/2”)
275 kg (606 lb)

w: 950 mm (37 3/8”) h: 2260 mm (89”) d: 800 mm (31 1/2”)
295 kg (650 lb)

ELECTRICAL AND WATER SUPPLY

Electrical requirement:

Potable water supply pressure:

Water supply tube:

PROVIDED INSTALLATION ACCESSORIES

Customized panel mounting kit (included with -OV models only)
Anti-tip kit
Lateral/side connecting kit
4 mm (1/8”) allen wrench

110V 60Hz 15a

From 7.3 TO 73 PSI

3/4” female attachment

TOOLS

The following tools are needed for the installation of the dishwasher:

• Phillips screw driver

• Drill and drill bits

• 3/4” open-end or adjustable wrench

• 1/2” wrench or socket

STEPS FOR INSTALLATION

The following pages provide the necessary information for proper installation of the refrigerator

and are arranged as follows:

• Technical data.

• Installation cutout dimensions, required clearances and mounting instructions.

• Electrical requirements and connections.

• Initial power-up and testing.

©2018 Hestan Commercial Corporation

4

LOCATION AND INSTALLATION

(continued)

INSTALLATION CUT-OUT FEATURES - KRP MODELS

A Area to be left clear for the anti-tip brackets

Cut-out Height
2134 mm (84”)

Cut-out Width
900 mm (35 1/2”)

Door Swing Clearance

1470 mm (57 7/8”)

140 (5 ½”) 140 (5 ½”)

A A

100 (4”)

900 (35 ½”)

100 (4”)

Door Opening Angle
105°

Width

899 mm (35 3/8”)

Height

2120 mm (83 1/2”) + 25 mm (1”)

Depth with door
635 mm (25”)

)

1016 (40”)

1470 (57 7⁄8”

105°

EN

230 (9”)

min 2134 (84”)

2120 (83 ½”) +25 (1”)

613 (24 1⁄8”)+25 (1”)

635 (25”)

560 (22”)
693 (27 ¼”)

5⁄8”)

8 (3⁄8”)

195 (7

1296 (50”)

8 (3⁄8”)

)

3/8”

516 (20

97 (3 7/8”)

635 (25”)

560 (22”)

75 (3”)

Flush

10 (3⁄8”)58 (2 ¼”)

899 (35 3/8”)

IMPORTANT

min 50 (2”)

min 10 (3⁄8”)

©2018 Hestan Commercial Corporation

5

LOCATION AND INSTALLATION

(continued)

INSTALLATION CUT-OUT FEATURES - KRB MODELS

EN

A

Area to be left clear for the anti-tip brackets

Cut-out Height
2134 mm (84”)

Cut-out Width

900 mm (35 1/2”)

Door Swing Clearance

1470 mm (57 7/8”)

140 (5 ½”) 140 (5 ½”)

100 (4”)

A A

½”)

900 (35

100 (4”)

Door Opening Angle
105°

Width
899 mm (35 3/8”)

Height

2120 mm (83 1/2”) + 25 mm (1”)

Depth with door (without panel)
610 mm (

FI36: 1470 (57 7⁄8”)

24” )

160 (6 3⁄8”)

992 (39”)

105°

min 2134 (84”)

2120 (83 ½”) +25 (1”)

610 (24”)

560 (22”)

20 ( )¾”

10 (3⁄8”)

560 (22”)

610 (24”)

899 (35 3⁄8”)

1293 (50 7⁄8” )

721 (28 3⁄8”) +25 (1”)

©2018 Hestan Commercial Corporation

6

500 (19 )¾”

474 (18 5⁄8” )

25 (1”)

+ 25 (1”)

) +

)

¾”

1⁄8”

248 (9

231 (9

LOCATION AND INSTALLATION

(continued)

INSTALLATION CUT-OUT FEATURES - KRP MODELS

24” AND 30” COLUMN REFRIGERATORS AND FREEZERS

24” WINE COLUMN AND 24” REFRIGERATOR WITH WINE

EN

A Area to be left clear for the anti-tip brackets

Cut-out Height
2134 mm (84”)

Cut-out Width
30”: 750 mm (29 5/8”)

24”: 600 mm (23 3/4”)

Door Swing Clearance

30” : 1325 mm (52 1/8”)
24” : 1175 mm (46 1/4”)

140 (5 ½”) 140 (5 ½”)

100 (4”)

A A

30”: 750 (29 5⁄8”)

100 (4”)

30”: 1325 (52 1/8”)

24”: 1175 (46 1/4”)

Door Opening Angle
105°

Width

30”: 749 mm (29 1/2”)
24”: 599 mm (23 5/8”)

Height

2120 mm (83 1/2”) + 25 mm (1”)

Depth with door (without panel)

615 mm (

24 1/4”)

30”: 53 (2 1⁄8”)
24”: 27 (1 1⁄16”)

105°

min 2134 (84”)

2120 (83 ½”) +25 (1”)

24”: 600 (23 ¾”)

560 (22 1/4”)

615 (24” 1/4)

615 (24 1/4”)

560 (22 1/4”)

10 (3⁄8”)

30”: 761 (30”)
24”: 609 (24”)

1808 (71 )¼”

505 (19 ¾”)

25 (1”)

+ 25 (1”)

)

) +

¼”

1⁄8”

233 (9

231 (9

©2018 Hestan Commercial Corporation

7

LOCATION AND INSTALLATION

PREPARING THE INSTALLATION

(continued)

EN

Transport to installation site

and unpacking

Since this is a large and heavy appliance, before transporting the ap­pliance, check the access to the location where it will be installed
(door size, maneuvering space in stairwells, etc.).

The appliance is attached to the base of the packaging (pallet) through
four bolts which can be removed using a 17 mm (3/4”) wrench.
It is recommended to use a manual transporting device to move the
appliance to the installation site, and only at this point to remove the
base of the packaging.

The appliance should always be transported in a vertical position.
If this is not possible, transport the appliance laying on its rear side.

Once at the installation site, the appliance, which is equipped with four
wheels, can be taken off the pallet and positioned in the installation
area.

Operate as follows:

1

Take off the four bolts

means of a 17 mm (3/4”) wrench.

Remove the xing brackets

securing the appliance to the pallet by

3

and

4

.

To remove the front xing bracket

the rear wheel adjusting bolt 2 by means of a 13 mm (1/2”) wrench.

From the back of the unit and by means of a suitable, high duty hand

truck, remove the appliance and place it on the oor.

Be very careful to avoid any damage to oors. Delicate oors should be
protected with plywood, hard cardboard or similar material panels.

The appliance is very heavy.
Take maximum care during handling to
avoid injury.

The appliance should always be transported

in a vertical position.

Avoid at all costs leaning it on its front side.

, unscrew for one or two turns

3

2

1

3

4

1

©2018 Hestan Commercial Corporation

8

LOCATION AND INSTALLATION

(continued)

CUT-OUT DIMENSIONS AND INSTALLATION METHODS - FLUSH

Models

KRB36 Models

30” Columns

24” Columns and Wine

36”: 900 (35 ½”)
30”: 750 (29 5⁄8”)

24”: 600 (23 ¾”)

Cut-out

750 (29 5/8”)

600 (23 3/4”)

Panel Width

897 (35 1/4”)900 (35 1/2”)

747 (29 3/8”)

597 (23 1/2”)

A

6,5 (¼”)

A Lateral/side connection kit (included accessory)

AKRLJK

(for KRB, KRC, KFC, KWC and KRW Models)

AKRLJKP (for KRP Models)

EN

B

Central connection kit, required when joining 2 units)

(not included - must be ordered as a separate accessory)

A A

B

AKRCJK (for KRB, KRC, KFC, KWC and KRW Models)
AKRCJKP (for KRP Models)

CUT-OUT DIMENSIONS AND INSTALLATION METHODS - NON-FLUSH

Cut-outModels

MAXMIN

KRB36 Models

30” Columns

24” Columns and Wine

900 (35 1/2”)

750 (29 5/8”)

600 (23 3/4”)

914 (36”

762 (30”)

610 (24”)

)

36: 914 (36”)
30: 762 (30”)

24: 610 (24”)

A

A A

6,5 (¼”

)

)

10 (3/8”

A Lateral/side connection kit

©2018 Hestan Commercial Corporation

9

LOCATION AND INSTALLATION

ELECTRICAL AND WATER CONNECTION

E

EN

W

E

W

E

W

The appliances are delivered from the factory for operation at 110V­120V AC - 60Hz (US and Canada).
They are provided with a suitable supply cable and plug to be con­nected to an appropriate 15A socket (US and Canada) provided
with an effective grounding.
A circuit breaker should also be installed and should be easily ac­cessible so that it can be easily switched off before performing any
installation or maintenance.
To connect to the water supply system (for appliances equipped with
ice makers) a 1/4” waterline with accessible shut-off valve must be
supplied.

The appliance is provided with a water adapter elbow which is suit­able for high water pressure and complies the Food Regulations.
The water lter cartridge , which is provided with the appliance
should be installed according to the accompanying instructions. Use
only the new adapter which is supplied with the appliance. The so­lenoid connection on the appliance is 3/4” diameter but is metric
threaded. A standard garden hose threaded connector such as a
braided stainless hose found at typical hardware stores will strip or
damage the solenoid threads. Use only the supplied 1/4” quick con­nect elbow adapter for connecting a 1/4” copper or polyethylene
source water line to the appliance.

(continued)

Electrical cord length: 2000 mm (78 3/4”)
Water connection line length: 2500 mm (98 3/8”)

Do not use extension cords and/or multiple adapters for the power

E

W

supply connection.

The built-in Hestan lter cannot make it safe
to drink any water which is not suitable for
human consumption.

The appliance should be connected only to
a drinkable water supply system.

Electrical and water supply behind the unit

All other Models

KRP Models

Do not use extension cords or adapters.
Once the appliance is fully installed, con­nected to the water supply (if applicable) and
operational, in the event that the water sup­ply must be turned off,(touch the button
control panel to switch it off) before the main

on

water is shut off to prevent the appliance from
entering a ‘NO WATER IN’ alarm state.

©2018 Hestan Commercial Corporation

10

W

E

E

W

LOCATION AND INSTALLATION

(continued)

ELECTRICAL AND WATER CONNECTION

KRP MODELS

Back of appliance

Front of appliance

1

2

Operate as follows:

Unwind the electric cable and connect it directly to the wall socket.

Make sure the appliance is in the Stand-by condition and that all lights

are off; if not, press the Unit button to switch it off.

Connect the water line to the threaded connection at the base of the

1

unit.

Fit the other end of the hose to the water tap, use the gaskets provided

in the Owner’s Kit.

2

(continued)

EN

Water connectionElectrical connection

ALL OTHER MODELS

Electrical connection
Water connection

Firmly tighten with ngers - a tool/wrench should not be needed to
make a proper seal. Turn on the water and ensure all connections are
not leaking prior to pushing the unit into the opening.

Back of appliance

Operate as follows:

Unwind the electric cable and connect it directly to the wall socket.

Make sure the appliance is in the Stand-by condition and that all

lights are off; if not, press the Unit button

to switch it off.

Push the 1/4” source waterline fully into the elbow connector then

thread the elbow adapter to the solenoid at the back of the appli­ance.

Firmly tighted with ngers - a tool or wrench should not be needed
to make a proper seal. Turn on the water and ensure all connections
are not leaking prior to pushing the unit into the niche.

©2018 Hestan Commercial Corporation

11

LOCATION AND INSTALLATION

LEVELING THE REFRIGERATOR

EN

Adjust the appliance level by means of the front leveling feet
and the rear adjustable wheels.

Operate as follows:

After removing the bottom plinth or grill (it is kept in position by

magnets), adjust the height of the leveling feet 1 by means of a 17
mm (3/4”) open-end or adjustable wrench.

(continued)

2

2

1

1

Then adjust the height of the rear wheels by turning the front

adjusting bolts 2 clockwise or counter-clockwise as required.

Reinstall the bottom plinth or grill.

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT
OVERLAY MODELS (-OV)

1

2

Decorative door and bottom-drawer panels layout:

The dimensions of the panels are indicated in the table and draw­ings on pages 18-19.

Nevertheless, according to the requirements for aligning with other
kitchen structures, the door panel can be higher than the upper
edge of the refrigerator door, and the drawer panel can be lower
than the edge of the drawer.

The panels must be mounted using special braces which attach
to adjustable devices provided on the door and drawer and with
brackets that anchor and adjust the panel’s vertical direction.

Braces, brackets and xing screws are provided with the appliance
and must be applied to the panel as indicated.

3

©2018 Hestan Commercial Corporation

12

Operate as follows:

To prepare the panels to be mounted on the appliance, follow
these steps, working on the back of the panel.

Door Panel

Trace, a line dividing the panel width in half.

Starting from the bottom edge of the panel, mark the positioning

of the brackets.

Following the corresponding table, mark the external and then

the internal hole.

2

3

1

LOCATION AND INSTALLATION

(continued)

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT
OVERLAY MODELS (-OV)

(continued)

EN

4

5

6

Position the brackets on each set of marks to make sure they are

aligned 4, then drill holes through the panel (pay close attention to
the panel’s thickness)

Screw the brackets in place

5

6

7

Drawer Panel

When preparing the Drawer Panel, follow the same instructions as

per the door panel, but make sure measurements are taken starting
from the top edge. 7The support bracket faces the opposite way

(note images 4 and 8).

8

8

©2018 Hestan Commercial Corporation

13

LOCATION AND INSTALLATION

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT
OVERLAY MODELS (-OV)

PANEL DIMENSIONS

KRB36-OV

(continued)

(continued)

Hinge Left

A

B

C

D

E

F / G

897 (35 ¼”) 897 (35 ¼”)

355.5 (14”)

261 (10 ¼”)

418 (16 ½”)

386 (15 ¼”)

354.5 (14”) 354.5 (14”)

HOLE POSITIONS

Hinge Right

261 (10 ¼”)

355.5 (14”)

386 (15 ¼”)

418 (16 ½”)

A

B C

13 (½”)

¾”)

1285 (50 5⁄8”)

1163 (45

507.5 (20”)

¼”)

660 (26”)

157 (6

1⁄8”)

100 (4”)

382 (15

34 (1

3/8”)

D E

D E

3⁄8)”

34 (1

½”)

13 (

F G

¾”)max 635 (25”)

min 1390 (54

©2018 Hestan Commercial Corporation

14

LOCATION AND INSTALLATION

(continued)

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT
OVERLAY MODELS (-OV)

(continued)

PANEL / FRAME DIMENSIONS

KRWR24-OV MODELS

EN

Hinge Left

A

D

E

F / G

H

I

897 (35 ¼”) 897 (35 ¼”)

418 (16 ½”)

386 (15 ¼”)

354.5 (14”) 354.5 (14”)

412 (16 ¼”)

380 (15”)

HOLE POSITIONS

Hinge Right

386 (15 ¼”)

418 (16 ½”)

380 (15”)

412 (16 ¼”)

<200 (7 7⁄8”)

6,5 (

¼”)

A

6,5 (¼”)

135 (5 3⁄8”)

1075 (42 3⁄8” )

24”: 327 (12

7⁄8” )

135 (5

115 (4

3⁄8”)

½”)

1286 (50 5⁄8”)

1152,5 (45 3⁄8”)

507,5 (20”)

5⁄8”)

7⁄8”)

650,5 (25

148,5 (5

1⁄8”)

100 (4”)

382 (15

3⁄8)”

34 (1

H I

D E

34 (1

3⁄8)”

13 (

½”)

F G

min 1390 (54 ¾”)

max 635 (25”)

©2018 Hestan Commercial Corporation

15

LOCATION AND INSTALLATION

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT
OVERLAY MODELS (-OV)

EN

PANEL DIMENSIONS

(continued)

(continued)

30” -OV Column Models

Hinge Left

A

C

B

747 (29 3⁄8)”

343 (13 ½”)

343 (13 ½”)

HOLE POSITIONS

Hinge Right

747 (29 3⁄8)”

343 (13 ½”)

343 (13 ½”)

24”-OV Column Models

Hinge Left

597 (23 ½”) 597 (23 ½”)

276,5 (10 7⁄8)”

268 (10 ½”)

Hinge Right

268 (10 ½”)

276,5 (10 7⁄8)”

1

A

B C

13 (½”)

1271,5 (50”)

1797 (70 ¾”)

¼”)

165 (6 ½”)

690,5 (27

34 (1 3⁄8” 34 (1 3⁄8)”

112 (4 3⁄8”)

1⁄8”)

min 1933 (76

©2018 Hestan Commercial Corporation

16

LOCATION AND INSTALLATION

(continued)

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT
OVERLAY MODELS (-OV)

(continued)

FRAME DIMENSIONS

KWCR/L24-OV MODELS

Hinge Left

Hinge Right

EN

A

B

C

597 (23 ½”) 597 (23 ½”)

276,5 (10 7⁄8)”

268 (10 ½”)

HOLE POSITIONS

min 200

7⁄8”)

(7

268 (10 ½”)

276,5 (10 7⁄8)”

½”)

¼”)

165 (6

690,5 (27

1

A

B C

13 (½”)

34 (1 3⁄8” 34 (1 3⁄8)”

3⁄8”)

112 (4

1572 (62”)

24: 327 (12 7⁄8” )

135 (5

1271,5 (50”)

1797 (70 ¾”)

3⁄8” )135 (5 3⁄8” )

©2018 Hestan Commercial Corporation

1⁄8”)

min 1933 (76

17

LOCATION AND INSTALLATION

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT
OVERLAY MODELS (-OV)

EN

PANEL DIMENSIONS - KRBR/L36-OV AND KRWR/L24-OV MODELS

Panels can have thickness ranging between 18 mm (3/4”) and 28 mm (1-1/8“).
Door panels can have a maximum weight 23 kg (51 lbs) and drawer panels may be a maximum
weight of 11kg (25 lbs).
Exceeding these weights could void your warranty for any service issues which can be
attributed to overweight panels.

The hinge mechanism on Hestan refrigerators is considered to be `Zero-clearance`. The door
and drawer widths specied below assume the minimum niche width is being used and a 3.5mm
(1/8”) reveal is desired around the panels. Adjust your panel dimensions accordingly to your own
design criteria considering your niche width and your reveal. Minimum reveal / gap should not be
less than 1.5mm (1/16”).

(continued)

(continued)

Models

KRBR/L36-OV

KRWR/L24-OV

2121 (83 ½") + 25 (1")

Door/Drawer Width

A

897 (35 1/4”)

Door Cutout Width

B

N/A

327 (12 7/8”)597 (23 1/2”)

1390 (54 ¾”)

3 (1⁄8”)

min 200 (7 7⁄8”)

135

(5 3⁄8”)

115 (4 ½” )

135

(5 3⁄8”)

1075 (42 3⁄8”)

Example:

84” cut-out height
36” cut-out width
4” toe kick height
1/8” gap desired all around

©2018 Hestan Commercial Corporation

18

max 635 (25”)

min 540 (21 ¼”)

A B

Door panel:

Width: 35-3/4”
Height: 54-3/4”

Drawer panel:

Width: 35-3/4”
Height: 84”-1/8”-54-3/4”-1/8”-4”=25”
If you want a 6” toe kick height then your bottom drawer
panel height would be 23”

LOCATION AND INSTALLATION

(continued)

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT
OVERLAY MODELS (-OV)

(continued)

PANEL DIMENSIONS - 24” AND 30” COLUMN REFRIGERATORS AND FREEZERS

AND KWCR/L24-OV MODELS

Panels with width ranging between 18 mm (3/4 in) and 28 mm (1 1/8 in).

Door panels with weight max of 34 kg (75 lb)

Exceeding these weights could void your warranty for any service issues which can be attributed

to overweight panels.

The hinge mechanism on Hestan refrigerators is considered to be `Zero-clearance`. The door

and drawer widths specied below assume the minimum niche width is being used and a

3.5mm (1/8”) reveal is desired around the panels. Adjust your panel dimensions accordingly

to your own design criteria considering your niche width and your reveal. Minimum reveal

or gap should not be less than 1.5mm (1/16”).

EN

Models

30” Columns

24” Columns

KWCR/L24-OV

Door/Drawer Width

A

747 (29 3/8”)

597 (23 1/2”)

597 (23 1/2”) 327 (12 7/8”)

Door Cutout Width

N/A

N/A

7⁄8”)

B

min 200(7 7⁄8”)

135

(5 3⁄8”)

135

(5 3⁄8”)

1572 (62”)

2121 (83 ½") + 25 (1")

max 2028 (79

min 1933 (76 1⁄8”)

A B

©2018 Hestan Commercial Corporation

19