Hestan KDW24YW Installation manual

INDOOR CLEANING

Dishwasher

KDW

Installation Manual

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY, OR DEATH.

Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of this or any other appliance.

Installation and service must be performed by a qualiﬁed installer or service agency.

DO NOT REPAIR, REPLACE OR REMOVE ANY PART OF THE APPLIANCE UNLESS SPECIFICALLY RECOMMENDED IN THE MANUAL. IMPROPER INSTALLATION, SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THIS MANUAL FOR GUIDANCE. ALL OTHER SERVICING SHOULD BE DONE BY A QUALIFIED TECHNICIAN.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE INSTALLING OR USING YOUR APPLIANCE TO REDUCE THE RISK OF FIRE, BURN HAZARD, OR OTHER INJURY. KEEP THIS MANUAL FOR FUTURE REFERENCE.

SAFETY DEFINITIONS

DANGER. THIS INDICATES INFORMATION AND WARNINGS WHICH, IF NOT OBSERVED, MAY COMPROMISE PERSONAL SAFETY OR DAMAGE THE APPLIANCE.

DANGER OF ELECTROCUTION. THIS INDICATES INFORMATION AND

WARNINGS OF AN ELECTRICAL NATURE WHICH, IF NOT OBSERVED,

MAY COMPROMISE PERSONAL SAFETY OR DAMAGE THE APPLIANCE.

THIS HIGHLIGHTS GENERAL INFORMATION AND WARNINGS AND INDICATES THAT DAMAGE TO THE APPLIANCE OR PROPERTY MAY OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.

INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE. HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

TABLE OF CONTENTS

1 SAFETY PRECAUTIONS - BEFORE YOU BEGIN 2 MODEL NUMBERS 2 RATING LABEL 2 REGULATORY / CODE REQUIREMENTS 3 LOCATION AND INSTALLATION

MOUNTING THE OVERLAY DOOR PANEL

12 13 ATTACHING THE SIDE GASKETS

COMPLETING INSTALLATION AND TESTING

14 15 ELECTRICAL CONNECTIONS, SAFETY AND CAUTION

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

When properly cared for, your Hestan appliance will provide safe, reliable service for many years. When using this appliance, basic safety practices must be followed as outlined below.

IMPORTANT: Save these instructions for the local Utility Inspector’s use.

INSTALLER: Please leave these Installation Instructions with the owner.

OWNER: Please retain these Installation Instructions for future reference.

This appliance is NOT designed for installation in manufactured (mobile) homes or recreational park trailers. Do NOT install this appliance outdoors.

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing appliance. Before turning power ON, be sure all controls are in the OFF position. Failure to do so can result in death or electrical shock.

ELECTRICAL GROUNDING

• This appliance must be grounded. Grounding reduces the risk of electric shock in the event of a short circuit. Read the ELECTRICAL CONNECTIONS section of this manual for complete instructions.

• DO NOT ground to a gas pipe.

• DO NOT use an extension cord with this appliance.

• DO NOT have a fuse in the NEUTRAL or GROUNDING circuit. A fuse in the NEUTRAL or GROUNDING circuit could result in an electrical shock.

MODEL NUMBERS

DISHWASHER MODELS

Model No. Description Circuit Breaker Req’d

KDW24 24” Dishwasher, Stainless Door 15 Amp

KDW24-OV 24” Dishwasher, Overlay Door 15 Amp

KDW24-XX

NOTE: -XX indicates color model.

-BK for Stealth - Black

-YW for Sol - Yellow

-PP for Lush - Purple

-GG for Paciﬁc Fog - Graphite Gray

24” Dishwasher, Color Door 15 Amp

-WH for Froth - White

-OR for Citra - Orange

-BU for Prince - Blue

-RD for Matador - Red

-BG for Tin Roof - Burgundy

-GR for Grove - Green

-TQ for Bora Bora - Turquoise

RATING LABEL

The rating label contains important information about your Hestan appliance such as the model and serial number and electrical rating.

The rating label is located on the right side of the door edge.

If service is necessary, contact Hestan Customer Care with the model and serial number information shown on the label.

RATING LABEL

TYPICAL RATING LABEL

REGULATORY / CODE REQUIREMENTS

Installation of this dishwashing appliance must be made in accordance with local codes. In the absence of local codes, this unit should be installed in accordance with the National Electrical

Code and local codes.

This appliance must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Code

CSA C22.1

ANSI/NFPA 70

, or Canadian Electrical code

LOCATION AND INSTALLATION

UNPACKING AND PLACEMENT

Remove the outer carton and packing materials Do not remove the plastic ﬁlm covering the stainless-steel surfaces. This ﬁlm protects the ﬁnish from scratches until the appliance is installed in its ﬁnal position.

The unit is heavy and should be handled with care. Use proper safety equipment, such as gloves and 2 persons to move the appliance into position to avoid injury and to avoid damage to the ﬂoor or the appliance itself.

NOTICE

Do not lift or carry the appliance by the door or handle. This could damage the door hinges.

DO NOT USE A HAND TRUCK OR DOLLY ON THE FRONT OR REAR OF THE DISHWASHER. HANDLE AND MOVE FROM THE SIDES ONLY.

PREPARATION

Before moving the dishwasher, protect any ﬁnished ﬂooring and secure the door closed to prevent damage. DO NOT lift the dishwasher by the door handle.

Make sure that power can be provided to the location selected.

TOOLS

The following tools are needed for the installation of the dishwasher:

• Tape measure and straight edge or ruler

• Pencil

• Philips screw driver

• Level

• Plumbing pliers

• Hand or saber saw

• 13mm open-end or adjustable wrench

• File

• Drill and drill bit

• Safety gloves and goggles

STEPS FOR INSTALLATION

The following pages provide the necessary information for proper installation of the dishwasher

and are arranged as follows:

• Technical data.

• Installation cutout dimensions, required clearances and mounting instructions.

• Electrical requirements and connections.

• Leak inspection and testing.

LOCATION AND INSTALLATION

(continued)

INSTALLATION KIT SUPPLIED WITH DISHWASHER

The kit supplied with the dishwasher comprises:

(KDW24-OV model also contains B, C, D, and E)

• 1 steel adhesive steam guard (A)

•

• 1 template for door panel (B)

• 2 hooks for door panel (C)

• 8 screws for securing the door panel hooks (D)

• 2 screws for securing the door (E)

• 4 screws for ﬁxing the dishwasher to the adjacent walls (F)

• 2 upper ﬁxing screws (G)

• 2 screw caps (H)

PRODUCT / CUT-OUT DIMENSIONS

Product Dimensions:

Cut-out Dimensions:

D (height) E (width)

33-7/8” height

86.1 cm

23-11/16” wide

60.2 cm

F (depth)

22-5/8” min depth

57.5 cm

LOCATION AND INSTALLATION

CAUTION

(continued)

DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON THE SHARP EDGES OF THE APPLIANCE.

Remove the polystyrene rack blocks. Position the appliance in the chosen installation position. The sides and rear of the appliance can lie against kitchen units or walls. If the dishwasher is installed next to a heat source, separate it panel in order to prevent overheating and malfunctions.

BUILDING-IN A DISHWASHER BELOW A COOKTOP IS ABSOLUTELY FORBIDDEN. A DISHWASHER CAN BE BUILT-IN UNDERNEATH A CONVENTIONAL HOB PROVIDED THERE IS NO BREAK IN THE KITCHEN WORKTOP, AND THE DISHWASHER AND HOB ARE INSTALLED AND SECURED CORRECTLY, SO THAT NO HAZARDS ARE GENERATED.

MAKE SURE THE DISHWASHER HAS BEEN CORRECTLY INSTALLED AND GROUNDED BY A QUALIFIED FITTER. THIS SAFETY REQUIREMENT MUST BE MET. IN CASE OF DOUBT, CALL IN A QUALIFIED FITTER. THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS OR PROPERTY RESULTING FROM THE FAILURE TO GROUND THE APPLIANCE OR FROM A DEFECTIVE GROUND CONNECTION .

BEFORE PROCEEDING WITH INSTALLATION, DISCONNECT THE MAINS POWER SUPPLY FROM THE WORK AREA.

with a heat insulating

LEVELING

Level the appliance using the adjustable feet on the bottom. Use an open-ended wrench or socket to rotate the feet until the dishwasher is perfectly level. The rear foot can be adjusted with a 8 mm wrench or socket. Use a level to be certain the dishwasher is perfectly level. Leveling is vital for assuring correct dishwasher operation .

Make sure to leave a gap of at least 7/64” (3mm) between the top of the dishwasher and the bottom surface of the countertop.

LOCATION AND INSTALLATION

ELECTRICAL AND WATER CONNECTIONS

(continued)

Install the dishwasher to allow ease of access to the electrical and water connections

through the adjacent cabinetry. These connections must never be behind the dishwasher.

The inlet and drain hoses can be pointed in all directions but make sure that they are not bent, crushed or too tight. Tighten the ring nut after pointing the hoses in the required direction.

The illustration below indicates the distances to maintain between the dishwasher and

the various connections.

FIRE HAZARD! DO NOT COVER OR CRUSH THE CORD PLUG.

C A = 47” / 1200mm B = 59” / 1500mm C = 63” / 1600mm D = min. 16” / 400mm

A through hole with a diameter of at least 5/32” (8mm) is required to pass the hoses and power cord. Make sure there are no rough edges that could damage the power cord or hoses. If the dishwasher is installed in a metal unit protect the edge of the through hole for the hoses and power cord with a gasket. Do not use extension cords when making the electrical connection as these do not guarantee safety.

ATTENTION! INSTALLING THE DISHWASHER IN A NARROW SPACE MAY BEND OR CRUSH THE POWER CORD. TAKE GREAT CARE IN ORDER TO REDUCE THE POSSIBILITY OF DAMAGING THE POWER CORD WHEN INSTALLING OR REMOVING THE APPLIANCE.

LOCATION AND INSTALLATION

CONNECTING THE WATER SUPPLY

PREVENTING THE RISK OF CLOGGING OR DAMAGE:

IF THE PLUMBING IS NEW OR HAS NOT BEEN USED FOR A LONG TIME TIME, BEFORE CONNECTING TO THE WATER SUPPLY CHECK THAT THE WATER IS CLEAR AND FREE OF IMPURITIES, TO PREVENT DAMAGE TO THE APPLIANCE. THE DISHWASHER MUST ALWAYS BE CONNECTED TO THE THE WATER SYSTEM WITH NEW HOSES. OLD OR USED HOSES MUST

NEVER BE RE-USED.

(continued)

CONNECTING TO A WATER TAP

Connect the inlet hose to a threaded 3/4” cold water tap tting the supplied lter.

Firmly secure the hose by tightening the relative ring nut with your hands;

nish by tightening another 1/4 turn using a pair of plumbing pliers.

The dishwasher can be ﬁ lled with water at a temperature of less than 140°F 60°C.

If the appliance is ﬁ lled with hot water, washing times will be reduced by about 20 minutes, but efﬁ ciency will be slightly impaired. Make the connection to the domestic hot water tap using the same methods described for connecting the appliance to the cold water tap.

• Recommended temperature: 49°C (120°F), max. 60°C (140°F).

• Recommended water pressure: 0.5 - 9 bar (7 -130 PSI).

If the pressure is too high, use a pressure reducer.

A rubber hose connected to a sink spray may burst if installed on the

same pipes feeding the dishwasher. If your sink is ﬁ tted with this accessory, remove the hose and plug the hole.

LOCATION AND INSTALLATION

(continued)

CONNECTING TO A WATER TAP

Do not cut the inlet hose. If the hose is cut, the dishwasher will not work, water will leak and you may be injured. The cable harness and electrical components must not come into contact with the hydraulic system and the water inlet and drain hoses.

When connecting the dishwasher drain hose to the sink make sure that the hose is not bent in order to prevent cracks or breakages that could damage it.

If the hose is too long, wind it up neatly and place it behind the appliance.

(continued)

CONNECTING TO A “T” UNION FOR DRAINAGE

MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED.

Connect the dishwasher drain hose to the “T” union of the drain using a

1-1/2 to 2” (38 to 50 mm) screw clamp* if necessary, cut the end of the

dishwasher drain hose (DO NOT cut the corrugated section).

* Available from any plumbing store

LOCATION AND INSTALLATION

(continued)

CONNECTING TO A WASTE DISPOSAL UNIT WITH AN AIR GAP

MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 15-3/4” (400 mm) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED.

Remove the cover of the waste disposal unit (A) .

Connect the dishwasher drain hose (B ) to the air gap (C)

clamp (D ) ; if necessary, cut the

end of the dishwasher drain hose (E ) (do not cut the

using the wide spring

corrugated section). If the drain hose has been cut, use a 38 to 50 mm (1-1/2 to 2”) screw clamp*.

To connect the air gap (ref. C ) to the waste disposal unit inlet (F)

use a rubber union* (G ) with spring or screw clamps*

* Available from any plumbing store

CONNECTING TO THE AIR GAP WITHOUT A WASTE DISPOSAL UNIT

MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 15-3/4” (400 mm) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED

Connect the dishwasher drain hose (ref. B ) to the air gap (C )

1. clamp (D) ; if necessary, cut the

end of the dishwasher drain hose (E ) (do not cut the corrugated section). If the drain hose has been cut, use a 38 to 50 mm (1-1/2 to 2”) screw clamp*.

To connect the air gap (ref. C ) to the waste disposal unit inlet (F )

use a rubber union* (G ) with spring or screw clamps*

* Available from any plumbing store

using the wide spring

+ 25 hidden pages

Hestan KDW24YW Installation manual

Specifications and Main Features

Frequently Asked Questions

User Manual