Henny Penny 581 User Manual

Henny Penny Model 581

SECTION 7. PARTS INFORMATION

7-1. INTRODUCTION This section lists the replaceable parts of the Henny Penny

Model 581 fryer.

7-2. GENUINE PARTS

part of lesser quality or substitute design may result in damage
to the unit or personal injury.

7-3. WHEN ORDERING PARTS

parts list, write down the following information:

Item Number 2
Part Number 16738
Description High Limit

From the data plate, list the following information:

Product Number 01100
Serial Number 0001
Voltage 208

7-4. PRICES

Your distributor has a price parts list and will be glad to inform

you of the cost of your parts order.

7-5. DELIVERY

Commonly replaced items are stocked by your distributor and
will be sent out when your order is received. Other parts will
be ordered, by your distributor, from Henny Penny
Corporation. Normally, these will be sent to your distributor
within three working days.

7-6. WARRANTY

for 90 days against manufacturing defects and workmanship.
If damage occurs during shipping, notify the carrier at once so
that a claim may be properly filed. Refer to warranty in the
front of this manual for other rights and limitations.

7-7. RECOMMENDED

SPARE PARTS FOR
DISTRIBUTORS
variations are marked. Distributors should order parts based
upon common voltages and equipment sold in their territory.

206 7-1

Use only genuine Henny Penny parts in your fryer. Using a

Once the parts that you want to order have been found in the

Example:

Example:

All replacement parts (except lamps and fuses) are warranted

Recommended replacement parts, stocked by your distributor,

are indicated with √ in the parts lists. Please use care when

ordering recommended parts, because all voltages and

Henny Penny Model 581

FIGURE UNITS
& ITEM PART PER
NO. NUMBER DESCRIPTION ASSY

1 35726 COVER, Rear Shroud Stud Assembly. .............................. 1

2 36190 CARRIAGE TRACK STUD ASSEMBLY, L.H. ............. 1

3 NS02-005 NUT, (#6-32 Hex Keps). ................................................... *

4 35057 SLIDE, Shroud (Inner) ....................................................... 2

5 35248 SLIDE, Shroud (Outer) ...................................................... 2

6 36839 SLIDE. ............................................................................... 2

7 62085 WELDMENT, Shroud ...................................................... 1

11 37233 PIN, Stop ............................................................................ 2

15 EF02-003 WIRE TIE .......................................................................... *

16 EF02-037 CLAMP .............................................................................. 1

17 37143 DEFLECTOR, Steam ........................................................ 1

18 SC01-034 SCREW, Machine (#8-32 x 3/8) ........................................ 1

19 SC04-003 SCREW, THD Cutting, (#8-32 x 3/8 P PHD TYPE F) ..... 2

20 35053 PANEL, Left Side .............................................................. 1

21 35166 PANEL, Control Weldment (Computron 7000 controls).. 1

22 31299 STUD ASSEMBLY COVER, Control Panel (C7000)....... 1

23 31271 HINGE SPRING (Computron 7000 controls) .................... 2

√ 24 14455 KIT, 581 – C7000 to C8000 – 60 hz................................... 1

√ 24 14456 KIT, 581 – C7000 to C8000 – 50 hz................................... 1

√ 24 66250RB ASSY – C8000 – Panel Only..................................... 1

25 36391 DECAL – C7000................................................................. 1

25 24849 DECAL – C8000................................................................. 1

√ 26 30261 SWITCH, Power (Computron 7000 controls) ................... 1

√ 26 29898 SWITCH. Power (Computron 8000 controls) .................... 1

√ 27 16624 LIGHT, Indicator ................................................................ 1

√ 27 54085 LIGHT, Indicator – Green - CE.......................................... 1

28 Use 14455 or 14456............................................................ 1

29 35881 CONDENSATION PAN ASSEMBLY ............................. 1

30 35069 FRAME .............................................................................. 1

31 36420 DECAL, Fill Instructions ................................................... 1

32 37246 CASTER, w/Brake ............................................................. 2

33 35181 COVER, Drain Rod Access. .............................................. 1

34 SC02-034 SCREW, (#8-AB or A x 1") .............................................. 2

35 35703 LATCH, Drain Rod ........................................................... 1

36 35705 LATCH RETAINER, Drain Rod ....................................... 1

37 35919 BLOCK, Latch Mounting. ................................................. 1

38 SC01-034 SCREW, Machine (#8-32 x 3/8”) ...................................... 2

39 36185 LATCH, Filter .................................................................... 1

√ Recommended Parts
* As Required

7-2 206

Henny Penny Model 581

FIGURE UNITS
& ITEM PART PER
NO. NUMBER DESCRIPTION ASSY

40 35855 LATCH PLATE, Drain Rod .............................................. 1

41 35899 LATCH PLATE SPACER ................................................. 1

42 17612 INSERT, Leg Casting ........................................................ 2

43 EF02-072 BUSHING, Split (3/4) ....................................................... 1

44 35107 BRACKET, Drain Rod Weldment ................................... 1

45 35154 CASTER ....................................................................... 2

46 NS03-017 NUT, (#U Type Clip) ......................................................... 1

47 35179 COVER, Access Cover (Before 12-01-05)......................... 1

47 36337 COVER, Access Cover (12-01-05 & after)........................ 1

48 SC02-023 SCREW, (#8-B x 3/8" PH THD SS)................................... 5

49 35416 WELDMENT, Contactor Bracket ..................................... 1

50 NS02-002 NUT, (1/4-20 Hex Keps) ................................................... 6

51 35677 CLAMP, Power Cord ......................................................... 1

52 SC04-011 SCREW, (#8-32 x 1/2" Slot Hex HD SS) .......................... 4

53 NS01-015 NUT – ¼-20 HEX (SN: GG015JJ & BELOW).................. 2

54 35924 BUSHING PLATE (SN: GG015JJ & BELOW) ................ 1

55 36075 SPRING, Magnet Plate (SN: GG015JJ & BELOW).......... 1

56 LW01-012 LOCKWASHER, (#10 Split Ring SS) .............................. 2

57 SC01-055 SCREW, (#10-32 x 3/4" Hex HD SS) ............................... 2

58 35923 PLATE/STUD ASSY (SN: GG015JJ & BELOW) ............ 1

59 35455 PLATE, Magnet Mounting ................................................ 1

60 WA01-002 WASHER, (1/4 Type B-Series R) ..................................... 2

61 SC04-006 SCREW, (1/4-20 x 1/2" Hex HD C) .................................. 2

62 35515 ANGLE MOUNT ............................................................... 2

63 NS02-010 NUT, (5/16-18 Hex Keps SS) ............................................ 8

64 SC01-057 SCREW, (1/4-20 x 1/2 Hex HD) ....................................... 4

65 SC01-042 SCREW, (3/8-16 x 1"Hex HD) .......................................... 2

66 SC01-104 SCREW, (1/4-20 x 1 1/2" Hex HD) .................................. 2

67 LW01-001 LOCKWASHER, (3/8 Split Ring) ..................................... 4

68 35484 LOCKPLATE, Hookarm ................................................... 2

69 35299 GUARD, Splash ................................................................. 1

70 36191 CARRIAGE TRACK STUD ASSEMBLY, R.H. ............. 1

71 35490 STOP, Carriage .................................................................. 2

72 NS01-024 NUT, (3/8-16 Hex SS) ....................................................... *

73 NS01-011 NUT, (#10-32 Hex) ............................................................ *

74 35954 PLATE, Support Pulley ...................................................... 6

75 18609 RETAINER, Str. Back ....................................................... 1

76 35047 BACK, Shroud ................................................................... 1

77 35962 BRACKET, Wheel Assembly ............................................ 2

78 36165 BRACE, Carriage Track..................................................... 2

79 35244 SPACER, Top Frame Brace ............................................... 2

*As Required

407 7-3

Henny Penny Model 581

FIGURE UNITS
& ITEM PART PER
NO. NUMBER DESCRIPTION ASSY.

80 35091 TOP FRAME BRACE..................................................... 1

81 SC01-160 SCREW, (1/4-20 x 1 1/4" Hex HD) ................................ 4

82 SC01-132 SCREW, (1/4-20 x 5/8" Soc. HD CAP SS ...................... 8

83 35725 ADAPTER HOSE EXHAUST ........................................ 1

√ 29524** KEYSWITCH ASSEMBLY (before Oct. 5, 2001)......... 1

√ 28980** RELAY, 12 Volt (before Oct. 5, 2001) ........................... 1

√ ME90-007** RELAY, 240 Volt (before Oct. 5, 2001) ......................... 1

√ 31900** SWITCH BOARD (before Oct. 5, 2001)......................... 1

36421** INSULATOR-SWITCH BOARD (before Oct. 5, 2001). 1

36404** WIRE BASKET............................................................... 8

36374** BASKET HANDLE......................................................... 2

38907** BASKET HANDLE - K-MART ..................................... 2

44782** LID - WIRE BASKET..................................................... 1

√ 26974** SPEAKER ASSY. (C8000 Controls) .............................. 1

EF02-120** CONDUIT CLAMP – 1.25” – 2 HOLE (power cord)............. 1

√ Recommended Parts
* As Required
** Not Shown

7-4 206

Henny Penny Model 581

1005 7-5

Y

1

Henny Penny Model 581

FIGURE UNITS
& ITEM PART PER
NO. NUMBER DESCRIPTION ASSY

1 SC01-083 SCREW, (#10-32 x 1/2 PH FHD) *
2 35101 SUPPORT, Element - Long 5
3 35100 SUPPORT, Element - Short 5
4 SCO1-074 SCREW, (#10-32 x 1/2 PH THD S) *
5 35435 BRACKET, Hi Limit Probe 3
6 35462 BRACKET, Hi Limit Probe 3

√ 7 35234 HEAT ELEMENT ASSEMBLY, 8.5 KW 208V 2
√ 35598 HEAT ELEMENT, 8.5 KW 240V 2
√ 48367 HEAT ELEMENT, 230 V(Int’l Only) 2
√ 36290 HEAT ELEMENT, 220 V(Int’l Only) 2

8 16855 SEAL, O-Ring 4
9 WAO1-005 WASHER, (5/8 Dia. Type A - Series N) 8
10 NSO1-017 NUT, (5/8-18 B Hex) 4
11 Not Avail. WELDMENT, Pot & Countertop 1
12 35797 WELDMENT, Insul. Box Upr. Middle 2
13 WA02-001 WASHER, Insulation 1-1/2 x.015 *
14 SC03-005 SCREW, (#8-AB x .50 PH PHD) *
15 35519 INSULATION, Side Panel 2
16 NS02-007 NUT, (#8-32 C Hex Keps) 4
17 35326 INSULATION, Upper Front 1
18 35531 WELDMENT, Insulation Box (Front) 1
19 SCO1-053 SCREW, (#8-32 x 1/2 PH RHDS) 1
20 35328 INSULATION, Front Cutout 3.19 x 7.00 1
21 35327 INSULATION, Front Cutout 6.5 x 7.00 1
22 35334 INSULATION, Middle 1
23 35529 WELDMENT, Insulation Box, (Middle) 1
24 35333 INSULATION, Bottom Back 1
25 35528 WELDMENT, Insulation Box, (Bottom) 1
26 35081 BOX, Insulation, Bottom 1
27 35332 INSULATION, Bottom Sides 2
28 35329 INSULATION, Upper Rear 1
29 35530 WELDMENT, Insulation Box, (Rear) 1

√ Recommended Parts

206 7-7

Y

\

\

i

Henny Penny Model 581

FIGURE UNITS
& ITEM PART PER
NO. NUMBER DESCRIPTION ASSY.

1 35026 ARM, Lid Support 2

√ 2 35207 CABLE 2

3 NS01-025 NUT, HEX 5/16-18 SS 10
4 LW0l-010 WASHER, 3/8 Split Ring SS 10
5 35092 CARRIAGE 1
6 SC01-069 SCREW, 3/8-16 x 1-1/2 Hex HD S2P 8
7 36839 SLIDE 2
8 SC01-042 SCREW, 3/8-16 x 1 Hex C 2
9 36625 WELD ASSEMBLY, C/W Carriage 1
10 36627 COUNTERWEIGHT BAR 7
11 36626 SPACER, C/W Frame 2
12 37362 WHEEL, Carriage 4
13 37363 SPACER, Carriage Wheel 4
14 37364 SPINDLE 4
15 SC01-009 SCREW, 1/4-20 x 1/2 P THD 1
16 35438 MAGNET, Ceramic (Small) 1
17 SC01-081 SCREW, 3/8-24 x 3/4 Hex HD SS 4
18 NS02-002 NUT, 1/4-20 Hex Keps 1

√ Recommended Parts

206 7-9

Henny Penny Model 581

7-10 407

Henny Penny Model 581

FIGURE UNITS
& ITEM PART PER
NO. NUMBER DESCRIPTION ASSY

1 35792 LID INSTRUCTION LABEL ........................................ 1

2 35675 FILLER, Lid ................................................................... 2

3 35243 COVER, Lid, Main ......................................................... 1

4 35413 PLATE, Trip ................................................................... 1

√ 5 52627 Pressure Pad Assembly ................................................... 2

5 49864 Pressure Pad (use 52627) ............................................. 2

6 49852 Bushing (not shown) .................................................... 2

7 SC01-204 Screw 1/4-20 x 1.00 Sock Butt Hd .............................. 2

8 37171 SHIM, Lid (.030) ............................................................ 1

9 49962 PLATE, Shim Assembly (L.H.) ..................................... 1

10 49890 PLATE, Cam Guide (L.H.) ............................................. 1

11 35359 SLIDE, (6") ..................................................................... 2

12 16121 RING, (Tru-Arc) Latch Pin ............................................ 1

13 WA01-020 WASHER, Lid Stop ........................................................ 1

14 51531 CAST, Lid Stop .............................................................. 1

16 SC01-074 SCREW, #10-32 x 1/2 PH THD SS ............................... 8

17 35223 WASHER, Special .......................................................... 1

18 35227 ROLLER, Linkage Shaft ................................................ 2

19 35339 GUIDE, Handle Side ...................................................... 2

20 SC01-062 SCREW, #6-32 x 3/8 PH FH .......................................... 4

22 SC01-041 SCREW, 5/16-18 x 1.00 Hex HD C ............................... 2

23 36285 WELDMENT, Handle Tap Plate .................................... 1

√ 25 34526 GASKET, LID - SN: AC0712021 & below ................... 1

√ 25 66620 GASKET, LID - SN: AC0712022 & above ................... 1

26 35945 PIN, Lid Support ............................................................. 1

27 35032 PIN, Lid Support ............................................................. 1

28 RR01-010 RING, Ret. 3/4 Shaft SS ................................................. 2

29 36312 WASHER, Lid Hinge ..................................................... 2

30 51697 PIN, Lid Hinge ................................................................ 1

31 49895 PLATE, Cam Guide (R.H.) ............................................ 1

32 49963 PLATE Shim Assembly (R.H.) ...................................... 1

33 SC01-146 SCREW, 1/4-20 x 3/4 Hex HD SS ................................. 2

34 52477 LIFT, Lid ........................................................................ 1

√ 35 35465 CAM SLIDE FILLER .................................................... 2

36 52497 LATCH ASSEMBLY, Coated ....................................... 1

37 72377 ASSY – REBUILT LID ................................................. 1

38 52498 LATCH SPRING (not shown) ....................................... 1

39 SC01-214 SCREW, Latch, 10-32 x 1 PH THD SS (not shown) ..... 2

40 LW02-006 LOCKWASHER, Latch (not shown) ............................. 2

41 52728 SHIM, Lid Lift (not shown) ............................................ 1

√ Recommended Parts

307 7-11

Henny Penny Model 581

FIGURE UNITS
& ITEM PART PER
NO. NUMBER DESCRIPTION ASSY.

1 35686 TUBE, DW to Exhaust Stack SS ...................................... 1

2 MS01-297 HOSE CLAMP, SS - .500 – 1.062 DID............................ 4

3 35693 TUBE, Exhaust Connect ................................................... 1

4 35696 WELDMENT, Steam Exhaust Box Lid............................ 1

5 SC02-014 SCREW, #8 AB x 3/8 P THD SS .................................... 4

6 35687 WELDMENT, Steam Exhaust Box .................................. 1

7 35694 TUBE, Condensate............................................................ 1

8 70312 ASSEMBLY, Restrictor Weld.......................................... 1

9 MS01-315 HOSE CLAMP, ½ x 1-3/4 SS........................................... 2

10 NS01-011 NUT, (#10-32 Hex)........................................................... 1

11 36851 BRACKET, Hose.............................................................. 1

12 21877 TUBING, Steam Exhaust .................................................. 4

7-12 206

Henny Penny Model 581

FIGURE UNITS
& ITEM PART PER
NO. NUMBER DESCRIPTION ASSY

√ 1 16910 PRESSURE GAUGE...................................................................... 1

√ 2 59742 RELIEF VALVE ASSY ................................................................. 1

3 FP01-127 ELBOW, Street, ½ x ½, 90 Degree................................................. 1

4 FP01-063 REDUCER, ½ NPT M to ¼ NPT F ................................................ 1

5 FP01-011 PIPE TEE, ½ NPT 304 SS.............................................................. 2

6 FP01-028 NIPPLE, Close ½ NPT ................................................................... 2

7 17407 CONNECTOR, ½ Male Elbow....................................................... 3

8 16817 FITTING, Sleeve Teflon................................................................. *

9 16809 NUT FITTING................................................................................ *

10 56307 CAP, Dead Weight ......................................................................... 1

11 16902 SEAL “O” RING ............................................................................ 1

12 16904 DEAD WEIGHT – 9#..................................................................... 1

13 16906 ORIFICE, 9 PSI .............................................................................. 1

14 16852 BODY, Valve.................................................................................. 1

15 35686 TUBE, DW to Exhaust Stack.......................................................... 1

16 35817 PIPE NIPPLE, ½ x 2 ¼ SS ............................................................. 1

17 16804 UMBRELLA GROMMET ............................................................. 1

18 35200 UMBRELLA GRAMMET ............................................................. 1

19 35474 PIPE NIPPLE, ½ x 2....................................................................... 1

20 FP01-066 COUPLING, ½ NPT SS ................................................................. 1

21 16807 FITTING CONNECTOR, Male...................................................... 1

22 35147 TUBE, Steam Exhaust - Up ............................................................ 1

23 18721 VALVE, Solenoid........................................................................... 1

24 16808 FITTING SLEEVE, Steel ............................................................... 1

√ Recommended Parts

206 7-13

Henny Penny Model 581

FIGURE UNITS

& ITEM PART PER
NO. NUMBER DESCRIPTION ASSY

1 19683 BRACKET, Mercury Contactor 1

√ 2 29942 CONTACTOR, Mercury 208/240 VAC 1
√ 2** 65075 E/M HEAT CONTACTOR-CE-240V (UK) 1
√ 2** 65074 E/M HEAT CONTACTOR-CE-230V 1

3 SC04-003 SCREW, #8-32 x 3/8 P PHD 2
4 35416 WELDMENT, Contactor Bracket 1
5 NS02-005 NUT, #6-32 Hex Keps *
6 35107 BRACKET, Drain Rod Weldment 1

√ 7 EF02-006 FUSE HOLDER 2
√ 8 EF02-007 FUSE, 15 Amp 2

9 SCO1-010 SCREW #6-32 x 1/2 PH PHD 4

√ 10 MS01-197 RECEPTACLE, NEMA 5-15 1

10 56063 CORD ASSY, - CE 1
10 14721 KIT, 580 Receptacle Non-CE to CE 1
11 16102 SPINDLE KNOB, Red 1
12 17216 BRACKET, Hi-Limit Probe 1

√ 13 16738 TEMP. CONTROL, Hi-Limit - 450F 1

14 SC04-004 SCREW, #8-32 x 3/8 P PHD 2

√ 15 18227 MICROSWITCH 1

16 35132 DRAIN ROD HANDLE 1
17 55139 LEVER – DRAIN VALVE 1
18 PN01-012 CLEVIS PIN, 1/4 x 1 SS 1
19 PN0l-002 COTTER PIN, 3/32 x 3/4 S 1
20 35521 SPLASH GUARD ASSEMBLY 1
21 55137 DRAIN VALVE & COUPLING ASSEMBLY. 1
22 17255 COTTER PIN, 9/64 x 1 ¼ 2
23 19405 CONTACTOR 208/240 VAC 1

√ 24 55167 PROBE, Temperature (Not Shown) 1

25 56065 ADAPTOR, CORD ASSY. – 580 to PF-180 1
(used in conjunction with 56063 with units of
SN: AG005II and below) (Not Shown)
26 54010 Cord & Plug Assembly (Not Shown) 1
35192 Plug – 120/208 – 4P, 5W, 60 Amp 1
35476 Cord Assembly 1
27 19923 TRANSFORMER, 480V (Not Shown) 1

Additional Parts for the European Community Units

√ 51057 FILTER, ASSEMBLY-EMC (Not Shown) 1

48369 SWITCH, COVER- Plastic (Not Shown) 1

Recommended Parts
**Not Shown

7-14 407

.

Henny Penny Model 581

407 7-15

Henny Penny Model 581

FIGURE UNITS
& ITEM PART PER
NO. NUMBER DESCRIPTION ASSY

.

3-7 SOLENOID VALVE ASSEMBLY
1 17121 VALVE, SOLENOID 120V, 60 Hz 1
1 18721 VALVE, SOLENOID 208-240V, 60 Hz 1
1 18724 VALVE, SOLENOID 208-240V, 50 Hz 1
√ 2* 17120 KIT, SOLENOID VALVE REPAIR 1
3 17101 CLIP, RETAINER 1
4 17109 RETAINER, SPRING 1
5 17110 SPRING, CORE 1
6 17111 CORE, DISC ASSEMBLY 1
7 17112 GASKET, BONNET 1
8 17114 SEAT, TEFLON 1
9 17115 GUIDE, DISC SPRING 1
10 17116 SPRING, DISC 1
11 17117 RING, SPRING RETAINER 1
12 17122 SEAT, O-RING SEAL 1

√ 13 17102 PLATE, SOLENOID NAME 1
√ 14 17103 COVER, COIL HOUSING 1
√ 15 17104 WASHER, COIL 2
√ 16 17105 YOKE, COIL 1
√ 17 17106 COIL, 120V, 60 Hz 1
√ 17 18706 COIL, 208-240V, 60 Hz 1
√ 17 18726 COIL, 208-240V, 50 Hz 1
√ 18 17123 HOUSING, COIL 1
√ 19 17108 BONNET, SOLENOID 1
√ 20 17113 BODY, SOLENOID VALVE 1
√ 21 17118 ADAPTER, PIPE 1
√ 22 SC01-132 SCREW, ADAPTER 2

√

recommended parts

* not shown

7-16 206

NOTE: ASSEMBLE CORE DISC ASSEMBLY
SMOOTH AND ROUNDED EDGE OF BLADE

TOWARD DISC SPRING GUIDE (ITEM 9).

E SEAT IN ANY WAY

WITH