Heitronic 30390, 30391, 30392, 30393 Installation and operating instructions

GB Installation and operating instructions

Heitronic

®

LED built in spotlight/floor spotlight
Art. no. 30390,30391,30392,30393

Many thanks for deciding to buy our lights.
Our LED light is made out of sturdy, high value materials and will provide you with quality lighting. The
light is suitable for installation on normal flammable surface. The light is suitable for use outdoors, for

lighting walkways in gardens or along pathways in gardens or parks. Load 5 kN.

Please read through the installation and operation instructions carefully and keep these in a
safe place for later reference.

We do not accept any liability for damage to persons or property caused by not following the
instructions, or improper use or for changes made to the product.

Packaging contents:

 1 pc built-in spotlight with connection line
 Installation and operating instructions

Technical Data:

Article Connection Model Luminant

30390 12V AC/DC

30391 12V AC/DC

30392 12V AC/DC

30393 12V AC/DC

round Ø 45 mm, ww
hole Ø 38 mm
angular 45x45 mm, ww
hole Ø 38 mm
round Ø 20 mm, ww
hole Ø 13 mm
angular 20 x 20 mm,ww
hole Ø 13 mm

1 spotlight each 1W
cannot be exchanged
1 spotlight with 1W
cannot be exchanged
1 spotlight with 0.2W
cannot be exchanged
1 spotlight with 0.2W
cannot be exchanged

LED­.

1 III, IP 67

1 III, IP 67

1 III, IP 67

1 III, IP 67

Protection
classes.

Safety and warning notice:

 Do not look directly into the LED beam- especially for longer periods of time - without

protecting your eyes. A LED beam should not be directed into other people's eyes.

 Make sure that the light has not been damaged during transportation before you put it into

service. Do not operate the light if the cable or the electrical parts are damaged

 Never make your own repairs to faulty parts. Repairs must be done by trained specialists.
 Keep the packaging material well away from children and household pets. Danger of

suffocation!

 Be careful. The packaging contains small parts which can be swallowed by small children.
 The entire product must not be changed or modified. Changes made to the light lead to

annulment of the guarantee (warranty).

 The secondary cable may not be extended.

Care and maintenance:

 You must make sure that the power supply has been disconnected before cleaning.
 Use a dry or a slightly moist cloth for cleaning.
 Never use chemicals, combustible cleaners or abrasives. These can damage the surfaces

and/or the insulation of the light.

Disposal:

 Used electronic devices must be brought back to public collection points and must not be

disposed of as household waste.

H. Vollmer GmbH
Allmendring 29
D-75203 Königsbach-Stein

Installation instructions Art. No. 30390- 30393 Page 1 of 2 Status 09.2013

Installation:

Heitronic

®

 Make sure that the connection value of your building installation for power supply to the light

corresponds with the data on the rating plate of this light.

 The light is suitable for installation on normal flammable upper surfaces. The light must not be

covered with thermally insulating covers or other materials under any circumstances
whatsoever.

 Unpack the individual parts and check for completeness
 Place the LED driver in its intended position. Sufficient ventilation at the place of installation is

necessary because of the self-generated heat from the LED driver. The ambient temperature
and the housing temperature of the LED driver have to be observed (see rating plate). The
LED driver can cause a slight buzzing sound during operations. Make sure that you do not
LED driver in a position where they do not act as resonance chambers to increase noise
pollution.

 Make sure that the base is suitable to support the weight of the light permanently and reliably.
 Do not bend the cable, make sure that the cable and the plug are free from strain and

rotational forces. Protect all the cables and insulations from possible damage.

 Mark the position of the built-in spotlight and cut out the necessary openings for the built-in

spotlight.

 Make sure you have a stable and reliable fastening.
 Make sure that the unused holes of the 6 X distributor are tightly closed.
 Connect the built-in spotlight to the LED driver.
 The connection of the LED driver is made to the power mains after the installation work.
 The rating plate must not be removed.

30390 30391 30392 30393

H. Vollmer GmbH
Allmendring 29
D-75203 Königsbach-Stein

Installation instructions Art. No. 30390- 30393 Page 2 of 2 Status 09.2013