TM
®
Dual Brite™
Motion Sensing
Coach Light
Models SL-4180/84 - A
Features
• Light comes on when motion is detected.
• Automatically turns light off.
• Dusk Accent lighting.
• Photocell keeps the light off during daylight hours.
This package includes:
Mounting screws
and wire
connectors
OPERATION
Mode: On-Time Works: Day Night
Test 5 Sec x x
Auto 1, 5 or 10 Min x
Manual To Dawn* x
Accent 3,6 Hr, to Dawn x
* resets to Auto Mode at dawn.
For TEST
Set the ON-TIME switch
on the bottom of the cover
plate to TEST.
For AUTO
Set ON-TIME switch to 1,
5 or 10 minutes.
For MANUAL OVERRIDE
Flip the light switch off for
one second then back on.
Manual override works
when the ON-TIME switch
is in any position.
TEST 1 5 10 MIN
TEST 1 5 10 MIN
1 Second OFF
then...
Grand
Manor
Candelabra
or
Tail Assembly
(Lantern & Coach)
Requirements
• The Light Control requires 120 volts AC.
• If you want to use Manual Override, the
control must be wired through a switch.
• Some codes require installation by a
qualified electrician.
Manual override only works
at night because daylight
returns the sensor to AUTO.
Mode Switching Summary
TEST
Turn
light
AUTO
switch
off for 10
Questions? Call 1-800-858-8501
8:00 AM to 4:45 PM Eastern Time,
weekdays.
Lo sentimos, pero no podemos contestar
preguntas en español por teléfono.
© Heath Company Printed in Hong Kong 595-5578
seconds
then
MANUAL OVERRIDE
back on*
* Wait one minute for sensor to warm up.
Dusk Accent Mode
Light comes on half bright for selected time
after dusk (Off, 3 hr., 6 hr., until dawn). If
motion is sensed, the light turns on full bright
for the ON-TIME (1, 5 or 10 minutes) then
returns to dim mode.
... back on.
ON-TIME
Switch at
1, 5 or 10
minutes
Flip light
switch
off for 1
second
then on
INSTALLATION
❒ Turn power off at circuit breaker.
1. Remove
two nuts.
2. Remove
Mounting Plate.
BLACK
WHITE
One Motion Light
OPTIONAL WIRING:
3. Set sensitivity range
SENS
MIN
MAX
4. Screw in mounting
on fixture back.
Junction
Box
plate to junction box.
Horizontal Junction Boxes Only:
Ground
Fixture
Screw
Notch
Junction
Box
Screws
Screw
Fixture
Screw
Remove ground screw and 2 fixture screws
from the mounting plate. Flip plate over and
rotate 90°. Re-insert ground screw. Insert the
2 fixture screws in the holes near the junction
box screws holes. Route wires through notch
in adaptor plate.
1. Connect Bare wire
to ground screw
BLACK
WHITE
Two Motion Lights
BLACK
WHITE
Wiring to Motion Light &
Standard Fixture
BLACK
RED to
BLACK
(Standard)
When wiring to additional standard
fixture only: Strip the motion sensor's
red wire and connect to the standard
light's black wire. Connect all white wires
together. Total fixture ratings must not
exceed 400W (3.3 A.).
Slide the fixture onto
the mounting screws
and tighten nuts.
2. White to white
❒ Caulk fixture and mounting surface
with silicone weather sealant.
❒ Install three 60W bulbs in candelabra
style lights.
3. Black to black
Adding Decorative Tail
2. Screw
in extension bar.
1. Remove
decorative nut
from bottom of
fixture.
3. Add tail
piece and
trim.
4. Screw
decorative
nut back on.
TESTING
❒
Turn on the circuit breaker and light
switch. There is a one minute warm-up
before the sensor will detect motion properly.
❒ Switch the on-time to TEST position
and Dual Brite™ switch to the off position.
TEST 1 5 10 MIN
Avoid aiming the control at:
• Pools of water or objects that change
temperature rapidly, such as heating
vents and air conditioners. These heat
sources could cause false triggering.
• Areas where pets or traffic may trigger
the control.
• Nearby large, light-colored objects reflecting daylight may trigger the shut-off
feature. Do not point other lights at the
sensor.
6 ft.
Maximum Maximum
Range Coverage Angle
OFF 3 6 DUSK TO
HOUR
30 ft.
DAWN
150°
The detector is less sensitive to motion
directly towards it.
Motion
Motion
Sensor
Least Sensitive Most Sensitive
❒ Walk through the coverage area noting
where you are when the lights turn on.
Rotate the sensor head (maximum 0f
45°left or right) to change the coverage
area.
90°
Maximum Sensor
Rotatation
45°
240°
45°
Maximum Aiming
Range
❒ Set the amount of TIME you want the
light to stay on after motion is detected.
TEST 1 5 10 MIN
OFF 3 6 DUSK TO
HOUR
DAWN
❒ Set the amount of time after dusk you
want the lights on accent level.
SPECIFICATIONS
Range . . . . . . . . . . . Up to 30 feet (varies during
daylight hours).
Sensing Angle . . . . . Up to 150°, 240° aimable
Electrical Load. . . . . (3) 60 W. candelabra,
400W (3.3 A.) total
Power Requirements 120 VAC, 60 Hz
Operating Modes. . . TEST, AUTO and
MANUAL OVERRIDE
Time Delay . . . . . . . 1 , 5, 10 minutes
Accent timer . . . . . . Off, 3, 6 Hrs, to dawn
Sensitivity . . . . . . . . Adjustable
The Heath Company reserves the right to discontinue
products and to change specifications at any time
without incurring any obligation to incorporate new
features in products previously sold.
TROUBLESHOOTING GUIDE
If you experience a problem, follow this guide. If the problem persists, call the
assistance at 1-800-858-8501 8:00 AM and 4:45 PM EST weekdays.
Lo sentimos, pero no podemos contestar preguntas en español por teléfono.
SYMPTOM
Light will not
come on.
Light comes
on in daylight.
Light comes
on for no
apparent
reason.
POSSIBLE CAUSE
1. Light switch is turned off.
2. Bulb is loose or burned out.
3. Fuse is blown or circuit
breaker is turned off.
4. Daylight turn-off is in effect
(recheck after dark).
5. Incorrect circuit wiring, if
this is a new installation.
6. Re-aim the sensor to cover
desired area.
1. Light Control may be installed in a relatively dark
location.
2. Light Control is in Test.
(Set
control switch to an ONTIME position.)
1. Light Control may be sensing small animals or automobile traffic
2. Sensitivity is set too high.
(re-aim sensor).
SYMPTOM
Light stays on
continuously.
Light flashes
on and off.
POSSIBLE CAUSE
1. The sensor is pointed at
nearby objects that cause
heat to trigger the sensor.
(Aim the sensor away from
nearby objects.)
2. The sensor is pointed
toward a heat source like
an air vent, dryer vent, or
brightly-painted heatreflective surface.
(Re-aim
sensor.)
1. Heat being reflected from
other objects may be
affecting the sensor.
(Re-
aim sensor.)
2. Light Control is in the Test
mode and warming up.
(Flashing is normal under
these conditions).
(Reduce sensitivity.)
YOUR HEATH ZENITH FIVE YEAR LIMITED WARRANTY
This is a “Limited Warranty” as defined in the U.S. Consumer Product Warranty and Federal Trade
Commission Improvement Act. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
For a period of five years from the date of purchase, any malfunction caused by factory defective
parts or workmanship will be corrected at no charge to you. Light bulbs are not covered. To obtain
a refund or a replacement, return the product to the place of purchase.
Not Covered — Repair service, adjustment and calibration due to misuse, abuse or negligence,
light bulbs and other expendable items are not covered by this warranty. Unauthorized service or
modification of the product or of any furnished component will void this warranty in its entirety. This
warranty does not include reimbursement for inconvenience, installation, set-up time, loss of use,
or unauthorized service.
This warranty covers only Heath Zenith assembled products and is not extended to other equipment
and components that a customer uses in conjunction with our products.
SUCH REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND
THERE SHALL BE NO LIABILITY ON THE PART OF HEATH FOR ANY SPECIAL, INDIRECT,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY
LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Loading...