Heath Zenith 598-1282-02 User Manual
LED Lighted
Push Button with
Keyfinder Light
Push Button
Keyfinder Lens
• The push button is set from the factory
for use with mechanical chimes, but
can be used with either mechanical or
electronic chimes.
• Follow these instructions to install your
push button and set it to work with your
particular chime.
IMPORTANT: Push button must be
installed with keyfinder light facing
downward.
© 2007 HeathCo LLC 598-1282-02
Installation
IMPORTANT: DO NOT install additional diode(s) to push button. Additional
diode(s) will cause chime to malfunction.
1. Using a small screwdriver, push in tab
on bottom of push button to remove
back (see Figure 1).
2. Insert wires through hole in center of
push button back. Attach back to wall
with screws provided (see Figure 2).
Figure 1 - Remove Push Button Back
Figure 2 - Attach Back to Wall
2 598-1282-02
3. Attach the two wires from your chime
and transformer to the screw terminals
on the back of your push button (see
Figure 3). Press push button to test
function.
4. If your chime functions correctly and
plays the entire tune, skip to step 9. If
your chime does not function correctly,
proceed with step 5.
Figure 3 - Attach Chime Wires to
Push Button (Back of Push Button Shown)
3598-1282-02
FRONT
TRANS
REAR
DO NOT OIL
Determine Chime Type
5. Locate your chime and remove the
cover. If you see tone bars and plungers
you have a mechanical chime (see
Figure 4). If not, you have an electronic
chime.
6. If you have a mechanical chime, go to
Troubleshooting section, page 7. If
the
you have an electronic chime proceed
to step 7 on page 5.
CAUTION: Do NOT connect push
button to mechanical chime if push
button jumper is set for electronic
chime use. Doing so may result in
permanent damage to your chime.
Plunger
Figure 4 - Inside Typical Mechanical Chime
4 598-1282-02
Tone Bar
7. If you have an electronic chime, move
the jumper on the back of your push
button from the two bottom pins to the
two top pins (see Figure 5). Press push
button to test again.
8.
If your chime still does not operate
correctly, see Troubleshooting, page 7.
Jumper On Two
Bottom Pins
for Mechanical
Chime
Figure 5 - Determining Correct Jumper
Position (Back of Push Button)
Jumper On
Two Top Pins
for Electronic
Chime
5598-1282-02
9.
Once your push button and chime are
wired and functioning correctly, insert
top of push button into top of back and
snap bottom of push button into place
(see Figure 6). Note: The push button
must be mounted with the keyfinder
lens facing downward.
Figure 6 - Attach Push Button onto Back
Troubleshooting
If bell or chime does not operate:
• For Electronic Chimes: If tune does
not play completely, reverse wires
connected to the push button.
• Disconnect wires from button and touch
together. If bell or chime operates,
replace with new button.
• Check transformer, bell, or chime.
6 598-1282-02
Technical Service
Please call 1-800-858-8501 (English
speaking only) for assistance before
returning product to store.
If you experience a problem, follow this
guide. You may also want to visit our
Web site at: www.hzsupport.com. If the
problem persists, call* for assistance at 1-
800-858-8501, 7:30 AM to 4:30 PM CST
(M-F). You may also write* to:
HeathCo LLC
P.O. Box 90004,
Bowling Green, KY 42102-9004
ATTN: Technical Service
* If contacting Technical Service, please
have the following information available:
Model Number, Date of Purchase, and
Place of Purchase.
No Service Parts Available for this
Product
Lifetime Finish Warranty
(Selected Models Only)
Full Lifetime Finish (plate only) warranty
to the original user (“User”) of Lifetime
Finish (“Product”) against premises
upon which the Product was originally
installed. This warranty DOES NOT
COVER: (I) scratches or abrasions, (II)
abused or misused Products, or (III) Products used in commercial applications.
HeathCo LLC reserves the right to discontinue
and to change specifications at any time without notice without incurring any obligation to
incorporate new features in previously sold
products.
7598-1282-02
ONE YEAR LIMITED WARRANTY
This is a “Limited Warranty” which gives you specific
legal rights. You may also have other rights which
vary from state to state or province to province.
For a period of one year from the date of purchase,
any malfunction caused by factory defective
parts or workmanship will be corrected at no
charge to you.
Not Covered - Repair service, adjustment and
calibration due to misuse, abuse or negligence,
light bulbs, batteries, and other expendable items
are not covered by this warranty. Unauthorized
service or modification of the product or of any
furnished component will void this warranty
in its entirety. This warranty does not include
reimbursement for inconvenience, installation,
setup time, loss of use, unauthorized service,
or return shipping charges.
This warranty covers only HeathCo LLC assembled products and is not extended to other
equipment and components that a customer
uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING ANY WARRANTY,
REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS
ARE FIT FOR ANY PARTICULAR PURPOSE
OR USE, AND SPECIFICALLY IN LIEU OF
ALL SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE
SOLE REMEDY OF THE CUSTOMER AND
THERE SHALL BE NO LIABILITY ON THE PART
OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT LIMITED
TO ANY LOSS OF BUSINESS OR PROFITS,
WHETHER OR NOT FORESEEABLE. Some
states or provinces do not allow the exclusion or
limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply
to you. Please keep your dated sales receipt, it
is required for all warranty requests.
8 598-1282-02
Loading...