Heath Zenith 598-1109-05 User Manual
Wireless Mechanical
1 2 3 4 5 6 7
ON
1 2 3 4 5 6
7
ON
Battery Operated
Chime
This package includes (Style of push button and chime may vary from illustration):
• Wireless chime
• Wireless push button w/battery
• Hardware pack
This chime requires 4 “C” alkaline batteries (not included). In typical use,
alkaline batteries will last up to 2 1/2 years.
WARNING: To prevent possible SERIOUS
INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify
Figure 1
Figure 2
doctor.
1. Install alkaline type A23 12 volt push button
battery (included). Remove back of case by
pushing in tab on bottom with a small screwdriver. See diagram inside push button for correct
battery orientation.
2. Remove chime cover.
Pull firmly as shown in
Figure 2.
3. Install 4 alkaline “C” batteries in chime.
Make
sure batteries are oriented properly as shown in
Figure 3.
4. Test range.
Temporarily position chime and
push button where you want them mounted.
Press push button to verify chime and push
button work properly. If chime does not sound,
see Troubleshooting.
Figure 3
© 2007 HeathCo LLC 598-1109-05
5. Mount push button. Use either screws or double sided
1 2 3 4 5 6 7
ON
tape to mount push button.
To mount with screws, remove back of case by push
ing in tab on bottom with a small screwdriver (see
Figure 1).
Attach back of case to door jamb or wall (see Figure
4). Snap front of push button on.
When attaching push button using double sided tape,
make sure the surface of the door jamb or wall is
clean.
6. Mount chime. There are three different ways to
mount the chime depending upon the model of chime
Figure 4
purchased. Determine which model you purchased
below. Mount the chime according to the instructions
for your chime.
Basic Chime with Separate Chime with Attached
Chime Decorative Cover Decorative Cover
Style of push button and chime may vary from illustration.
-
-2-
598-1109-05
Basic Chime:
1 2 3 4 5 6 7
ON
1 2 3 4 5 6 7
ON
1. Remove batteries from chime.
2. Place chime against wall and verify the chime is level.
3. Use chime holes as a template (see Figure 5). Drill 7/32" diameter pilot hole
for 2 wall anchors (provided) and insert anchors.
4. Insert 2 screws (provided) through holes in back of chime.
5. Using arrow inside chime unit as a guide, mount chime with arrow pointing
up (see Figure 5). Do not tighten completely.
6. Verify chime is level and tighten screws securely.
7. Replace batteries (see Figure 3). Snap cover onto chime base.
Holes
for Wall
Mount
Chime Unit
with Arrow
Pointing Up
Mounting
Figure 5
Chime with Separate Decorative Cover:
1. Slide cover pin onto rear of chime as shown in Figure 6. Pin must be assembled to base prior to mounting base to wall (pin may be pre-assembled).
2. Follow directions under “Basic Chime” to mount chime base to wall.
3. Hang cover on cover pin.
Top of Chime
598-1109-05
Cover Pin
Installed on
Chime Back
Cover Pin
Back of Chime
Figure 6
-3-
Chime with Attached Decorative
Cover:
1. Mount hanger to chime (hanger
may be pre-assembled):
• Place hanger over predrilled
holes (either in top or bottom
Hanger
Predrilled
Hanger
Holes
panel).
• Connect hanger to chime using
#4 Screws
2 #4 screws (provided).
2. Determine where chime is to be
mounted.
3. Drill 1/4" diameter pilot hole for
wall anchor (provided) and insert
Figure 7
anchor.
4. Screw #8 screw (provided) into anchor. Leave 1/16" gap between screw head
and wall.
5. Place hanger over screw to mount chime.
-4-
598-1109-05
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Tune Settings
Your wireless chime has different selectable tunes: Dong (one note) and DingDong (two note). The factory setting is for the Ding-Dong tune. This tune can
be changed by following the instructions below.
• Dong (one note tune)
Inside Push Button: Add jumper to location 8.
• Ding-Dong (two note tune)
Inside Push Button: Remove jumper from location 8.
Note: All Heath®/Zenith models have both front and back door tune capabili-
ties. We recommend the back door use the Dong tune and the front door use
the Ding-Dong tune. Models that include two push buttons will come factory
set for front and back doors. Decals on the rear of the push button will indicate
its setting.
Tune Setting
Push Button Set
for One Note Tune
(Dong)
Figure 8 - Inside Push Button
Push Button Set
for Two Note Tune
(Ding-Dong)
598-1109-05
Note: Some models might require
the use of tweezers to remove
and replace the jumpers.
-5-
A. Low Battery Indicator: When the push button designated for the “Ding-Dong”
Troubleshooting
tone is pressed, only a “Dong” note will play when battery power is low in
chime unit.
B. Chime does not sound:
• Make sure push button and chime codes are the same (see Figure 9).
• Check orientation of push button and chime batteries (See diagram inside
push button and chime for correct battery orientation.)
• Check charge of push button and chime batteries, replace if necessary.
C. Chime sounds when not intended (false triggers): Chime is receiving
interference from another wireless device; change the code setting (see
Code Setting below).
D. Batteries seem OK, but the chime does not work when installed:
• Do not mount chime or push button on metal or near metal studs. This
reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims
to move chime or push button off metal surface.
• Concrete floors may reduce range. Move chime away from floor.
• Try locating chime closer to push button.
E. Code Setting:
It is recommended to only change one code position at a time and then check
to see if system is functioning properly.
1. Open the cases and locate the jumpers on the push button and the switches
on the chime (see Figure 9).
2. The push button has eight different jumper locations and the chime has seven
switches. Jumper positions 1 through 7 on the push button and the switches
on the chime are used for setting the code.
3. To change the code, either:
• Add a jumper to the push button and set the matching chime switch to
“ON” or...
• Remove a jumper on the push button and set the matching chime switch
to “OFF” or...
• Move a jumper in the push button from one location to another. Turn “OFF”
the chime switch matching the first location and turn “ON” the chime switch
matching the new location of the jumper.
Note: Code positions 1 through 7 must be exactly the same for both the
push button and chime for this system to function.
Note: Unit will come factory set with jumpers in locations 5, 6, and 7 on the
push button and switch locations 5, 6, and 7 in the “ON” position on the chime
(see Figure 9).
The range of the wireless chime can vary with location, temperature, and
battery condition.
-6-
598-1109-05
1
2
3
4
5
6
7
8
* Co de Se ttings 1-7
1 2 3 4 5 6 7
ON
Must Match Both Push
Button and Chime
Positions 5, 6, and 7
598-1109-05
Push Button
Jumpers on
Chime Switches
5, 6, and 7 in “ON”
Figure 9 - Inside Push Button and Chime
Note: Some models might require
the use of tweezers to remove
and replace the jumpers.
-7-
Position
Please call 1-800-858-8501 (English speaking only) for assistance
If you experience a problem, follow this guide. You may also want to visit our
Web site at: www.hzsupport.com. If the problem persists, call* for assistance
at 1-800-858-8501 (English speaking only), 7:30 AM to 4:30 PM CST (M-F).
You may also write* to:
HeathCo LLC
P.O. Box 90004, Bowling Green, KY 42102-9004
ATTN: Technical Service
* If contacting Technical Service, please have the following information available:
Model Number, Date of Purchase, and Place of Purchase.
before returning product to store.
No Service Parts Available for this Product
Regulatory Information
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry
Canada. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The user is cautioned that changes or modifications not expressly approved by
the party responsible for regulatory compliance could void the user’s authority
to operate the equipment.
Technical Service
-8-
598-1109-05
This is a “Limited Warranty” which gives you specific legal rights. You
ONE YEAR LIMITED WARRANTY
may also have other rights which vary from state to state or province
to province.
For a period of one year from the date of purchase, any malfunction
caused by factory defective parts or workmanship will be corrected at
no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse,
abuse or negligence, light bulbs, batteries, and other expendable items are
not covered by this warranty. Unauthorized service or modification of the
product or of any furnished component will void this warranty in its entirety.
This warranty does not include reimbursement for inconvenience, installation,
setup time, loss of use, unauthorized service, or return shipping charges.
This warranty covers only HeathCo LLC assembled products and is not
extended to other equipment and components that a customer uses in
conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE
PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND
SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE
CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART
OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY
LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion
may not apply to you. Please keep your dated sales receipt, it is required
for all warranty requests.
HeathCo LLC reserves the right to discontinue and to change specifications
at any time without notice without incurring any obligation to incorporate new
features in previously sold products.
598-1109-05
-9-
Loading...