Heath Zenith 595-5551-10 User Manual
Wireless Chime
This package includes (Style of push button and chime may vary from illustration):
• Wireless chime
• Wireless push button w/battery
• Hardware pack
You'll need to buy 2 “C” alkaline batteries for the chime. In typical use,
alkaline batteries will last up to one year.
1. Install alkaline type A23 12 volt push button
battery. Remove back of case by pushing in tab
on bottom with a small screwdriver. Make sure
battery is oriented properly (see page 3).
Case Style “A”
2.Open c hime ca s e .
Press in catch on bottom of chime and lift the
case open.
3. Install 2 alkaline “C”
batteries. Make sure
batteries are oriented
properly.
12345678
4. Test range. Temporarily position chime and
push button where you want them mounted.
Press push button to verify chime and push
button work properly. If chime does not sound,
see Troubleshooting.
5. Mount push button and chime.
Use either screws or double sided tape to mount
push button.
Case Style “B”
© 2007 HeathCo LLC 595-5551-10
To mount with screws, remove back of case by
pushing in tab on bottom with a small screwdriver.
Keyhole
1 9/16"
Holes
for Wall
Mounting
Case Style “A” Back
Attach back of case to door jamb or wall. Snap
front of push button on.
When attaching push button using double sided
tape, make sure the surface of the door jamb or
wall is clean.
Case Style “A”: Chime can be mounted by using
2 holes in the back of case, or by using 1 screw
with keyhole.
Case Style “B”: Chime can be mounted by using 1
screw with keyhole (see illustration on page 1).
Case Style “A”: Snap front of chime case on.
Start with top edge of case aligned with the top
of back plate.
Case Style “B”: Snap battery access door firmly
in place before mounting (See illustration on
page 1).
Code and Tune Settings
Note: Most installations will not require you to change any jumpers on
your chime and push button.
The push button and chime communicate by using a code that can be changed
by removing and/or adding jumpers on both the push button and chime. The
code is factory set; however, there are 128 selectable codes that allow you to
expand your system and prevent outside interference. Other wireless products
may cause interference and the system may not function properly. Follow the
instructions below for setting a new code.
1. Open the cases and locate the jumpers on both the push button and chime
(See illustration on page 3).
2. The push button and chime both have eight different jumper locations. The
jumper positions 1 through 7 are used for setting the code.
3. To change the code, add and/or remove jumpers as needed. It is recommended to only change one jumper at a time and then check to see if system
is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly
the same for both the push button and chime for this system to function.
Code Settings
-2-
595-5551-10
Your wireless chime has different selectable tunes: Ding (one note), Ding-Dong
Tune Settings
(two note), or Westminster (eight note) (Available on selected chimes). The
factory setting is for the Ding-Dong tune (or Westminster, when available). This
tune can be changed by following the instructions below.
• Ding (one note tune)
Push Button: Add a jumper to location 8.
• Ding-Dong (two note tune)
Push Button: Remove jumper from location 8.
Chime: Remove jumper from location 8.
• Westminster (Eight note tune) (Available on selected chimes)
Push Button: Remove jumper from location 8.
Chime: Add a jumper to location 8.
Note: All models have both front and back door tune capabilities. We recommend
the back door use the Ding tune and the front door use the Ding-Dong tune
(or Westminster tune, available on selected chimes). Models that include two
push buttons will come factory set for front and back doors. Decals on the rear
of the push button will indicate its setting.
Push Button Battery Replacement
Inside Chime
Install an alkaline type A23 12 Volt battery. The
positive terminal should be positioned as shown.
595-5551-10
1 2 3 4 5 6 7 8
Tune Setting
(Not used on
all models)
1 2 3 4 5 6 7 8
Inside Push
Button
-3-
* Code Settings 1-7
Must Match Both
Push Button and
Chime
Tune Setting
Note: Some models might require the use of tweezers to remove and replace the jumpers.
Chime does not sound:
Troubleshooting
• Make sure push button and chime codes are the same (See pages 2 and 3).
• Check orientation of push button battery (See page 3).
• Check charge of push button and chime batteries, replace if necessary.
Batteries seem OK, but the chime does not work when installed:
• Do not mount chime or push button on metal or near metal studs. This
reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to
move chime or push button off metal surface.
• Concrete floors may reduce range. Move chime away from floor.
• Try locating chime closer to push button.
The range of the wireless chime can vary with location, temperature and battery condition.
Please call 1-800-858-8501 (English speaking only) for assistance
If you experience a problem, follow this guide. You may also want to visit our
Web site at: www.hzsupport.com. If the problem persists, call* for assistance
at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:
HeathCo LLC
P.O. Box 90004, Bowling Green, KY 42102-9004
ATTN: Technical Service
* If contacting Technical Service, please have the following information available:
Model Number, Date of Purchase, and Place of Purchase.
before returning product to store.
No Service Parts Available for this Product
Regulatory Information
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry
Canada. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The user is cautioned that changes or modifications not expressly approved by
the party responsible for regulatory compliance could void the user’s authority
to operate the equipment.
Technical Service
-4-
595-5551-10
This is a “Limited Warranty” which gives you specific legal rights. You
ONE YEAR LIMITED WARRANTY
may also have other rights which vary from state to state or province
to province.
For a period of one year from the date of purchase, any malfunction
caused by factory defective parts or workmanship will be corrected at no
charge to you. To obtain a refund or a replacement, return the product to
the place of purchase.
Not Covered - Repair service, adjustment and calibration due to misuse,
abuse or negligence, and expendable items are not covered by this warranty.
Unauthorized service or modification of the product or of any furnished
component will void this warranty in its entirety. This warranty does not
include reimbursement for inconvenience, installation, setup time, loss of
use, or unauthorized service.
This warranty covers only HeathCo LLC assembled products and is not
extended to other equipment and components that a customer uses in
conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY,
REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR
THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE
OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE
CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART
OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY
LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion
may not apply to you. Please keep your dated sales receipt, it is required
for all warranty requests.
HeathCo LLC reserves the right to discontinue and to change specifications
at any time without notice without incurring any obligation to incorporate new
features in previously sold products.
595-5551-10
-5-
Loading...